Technical Data Sheet

Approved 15360;15380;38602 1,2 15360 epoxy ^(ValidationDate) 1

Jotacote Universal N10

Product description
This is a two component polyamine cured pure epoxy coating. It is a high solids, high build, abrasion resistant
product. Available with curing agents for standard, and for quick drying (QD) properties. Specially designed as a
universal, all round, all year, new building coating where fast dry to handle is required. Can be used as primer,
mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly
prepared aluminium, carbon steel, galvanised steel, shop primed steel and stainless steel substrate. It can be
applied at sub zero surface temperatures.

Typical use
Marine:
Exterior and interior areas, including outside hulls, superstructures, decks, cargo holds and water ballast tanks.
This product has very high flexibility making it specially suitable for the temperature variation experienced in
crude oil, chemical and shuttle tankers. Approved for PSPC cross over testing with a wide range of shop primers.
Other

Approvals and certificates

Approved for PSPC for Water Ballast Tanks according to IMO Res. MSC 215(82)
Approved for PSPC for Crude Oil Tanks according to IMO Res. MSC 288(87)

When used as part of an approved scheme, this material has the following certification:
- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5
and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with
IMO 2010 FTP Code Ch. 8

Consult your Jotun representative for details.

Additional certificates and approvals may be available on request.

Colours
aluminium, Aluminium red toned, black, buff, grey, red

Product data
Property Test/Standard Description

Standard grade
Solids by volume ISO 3233 72 ± 2 %
Gloss level (GU 60 °) ISO 2813 matt (0-35)
Flash point ISO 3679 Method 1 30 °C
Density calculated 1.4 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 240 g/l
(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
VOC-EU IED (2010/75/EU) (theoretical) 261 g/l
VOC-China GB/T 23985-2009 (tested) 239 g/l
VOC-Korea Korea Clean Air Conservation Act (tested) 275 g/l
(Max. thinning ratio included)

Date of issue: 13 July 2021 Page: 1/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotacote Universal N10

QD grade

Solids by volume ISO 3233 72 ± 2 %

Flash point ISO 3679 Method 1 31 °C
Density calculated 1.4 kg/l
VOC-US/Hong Kong US EPA method 24 (tested) 239 g/l
(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
VOC-EU IED (2010/75/EU) (theoretical) 263 g/l
VOC-China GB/T 23985-2009 (tested) 210 g/l
VOC-Korea Korea Clean Air Conservation Act (tested) 250 g/l

The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.

Film thickness per coat

Typical recommended specification range

Standard grade

Dry film thickness 75 - 300 μm

Wet film thickness 105 - 415 μm
Theoretical spreading rate 9.6 - 2.4 m²/l

QD grade

Dry film thickness 75 - 300 μm

Wet film thickness 105 - 415 μm
Theoretical spreading rate 9.6 - 2.4 m²/l

Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.

Surface preparation summary table

Surface preparation

Substrate Minimum Recommended

Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1)

Stainless steel The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using non-metallic
or bonded fibre machine or hand abrasive media which is suitable to
abrasive pads to impart a scratch achieve a sharp and angular surface
pattern to the surface. profile.
Aluminium The surface shall be hand or machine Abrasive blast cleaning to achieve a
abraded with non-metallic abrasives surface profile using non-metallic
or bonded fibre machine or hand abrasive media which is suitable to
abrasive pads to impart a scratch achieve a sharp and angular surface
pattern to the surface. profile.

Date of issue: 13 July 2021 Page: 2/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotacote Universal N10

Galvanised steel The surface shall be clean, dry and Sweep blast-cleaning using non-
appear with a rough and dull profile. metallic abrasive leaving a clean,
rough and even pattern.
Shop primed steel Dry, clean and intact shop primer. Sweep blasted or alternatively blasted
to Sa 2 (ISO 8501-1) of at least 70 %
of the surface.
Coated surfaces Clean, dry and undamaged compatible Sa 2½ (ISO 8501-1)
coating

Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is
achieved with recommended surface preparation.

Application
Application methods
The product can be applied by

Spray: Use airless spray.

Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller: May be used for small areas. Not recommended for first primer coat. Care must be taken
to achieve the specified dry film thickness.

Product mixing ratio (by volume)

Jotacote Universal N10 Comp A 3 part(s)

Jotacote Universal N10 Comp B 1 part(s)

Jotacote Universal N10 Comp A 3 part(s)

Jotacote Universal N10 QD Comp B 1 part(s)

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray

Nozzle tip (inch/1000): 17-27

Pressure at nozzle (minimum): 150 bar/2100 psi

Date of issue: 13 July 2021 Page: 3/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotacote Universal N10

Drying and Curing time

Substrate temperature -10 °C -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C

Standard grade

Surface (touch) dry 26 h 14 h 10 h 6h 5h 2 h 1h

Walk-on-dry 72 h 34 h 24 h 14 h 10 h 5 h 2h
Dry to over coat, minimum 36 h 22 h 15 h 9h 7h 4 h 2h
Dried/cured for immersion 14 d 7d 4d 3d 2d 1 d 12 h
Dried/cured for service 21 d 14 d 10 d 7 d 3d

QD grade

Surface (touch) dry 17 h 10 h 7h 4h 3h 1h

Walk-on-dry 40 h 25 h 20 h 10 h 7.5 h 3h
Dry to over coat, minimum 26 h 17 h 10 h 7h 5h 2h
Dried/cured for immersion 12 d 6d 4d 3d 2d 1d
Dried/cured for service 21 d 14 d 10 d 7d

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.

Dried/cured for immersion: Minimum time before the coating can be permanently immersed in sea water.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life

Paint temperature 23 °C

Standard grade

Induction time 10 min

Pot life 1.5 h

QD grade

Induction time 10 min

Pot life 1h

Date of issue: 13 July 2021 Page: 4/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotacote Universal N10

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C

Immersed, sea water 60 °C 70 °C
Immersed, crude oil 80 °C 90 °C

Peak temperature duration max. 1 hour.

The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical
and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If
used as part of a system, ensure all coatings in the system have similar heat resistance.

Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.

Previous coat: inorganic zinc silicate shop primer, epoxy, zinc epoxy, zinc silicate
Subsequent coat: acrylic, alkyd, epoxy, polyurethane, polysiloxane, vinyl epoxy, epoxy mastic, vinyl epoxy

Packaging (typical)
Volume Size of containers
(litres) (litres)

Jotacote Universal N10 Comp A 15 20

Jotacote Universal N10 Comp B 5 5
Jotacote Universal N10 QD Comp B 5 5

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.

Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.

Shelf life at 23 °C
Jotacote Universal N10 Comp A 48 month(s)
Jotacote Universal N10 Comp B 48 month(s)
Jotacote Universal N10 QD Comp B 48 month(s)

In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.

Date of issue: 13 July 2021 Page: 5/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com
Technical Data Sheet
Jotacote Universal N10

Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do
not inhale spray mist. Avoid skin contact. Spillage on the skin should immediately be removed with suitable
cleanser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.

Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.

Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue: 13 July 2021 Page: 6/6

This Technical Data Sheet supersedes those previously issued.

The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com