Omniswitch Aos Release 6 Transceivers Guide: 060568-10 Rev. A November 2018

060568-10 Rev.
A
November 2018
OmniSwitch AOS Release 6

Transceivers Guide
6.7.2.R05
www.al-enterprise.com
OmniSwitch AOS Release 6 Transceivers Guide November 2018 i

This user guide contains transceiver specifications and compatibility information for the
OmniSwitch 6350/6450 switches. The information described in this guide is subject to change
without notice.
Attention: Use of any transceivers other than those part numbers listed in the Compatibility Matri-
ces is prohibited. Failure to comply with these matrices is not guaranteed for proper performance
and may result in voiding the warranty for the affected platforms.
The Alcatel-Lucent name and logo are trademarks of Nokia used under license by ALE. To view other
trademarks used by affiliated companies of ALE Holding, visit: www.al-enterprise.com/en/legal/trade-
marks-copyright. All other trademarks are the property of their respective owners. The information
presented is subject to change without notice. Neither ALE Holding nor any of its affiliates assumes any
responsibility for inaccuracies contained herein.
26801 West Agoura Road

Calabasas, CA 91301
Service & Support Contact Information

North America: 800-995-2696
Latin America: 877-919-9526
EMEA : +800 00200100 (Toll Free) or +1(650)385-2193
Asia Pacific: +65 6240 8484
Web: businessportal2.alcatel-lucent.com
Email: ebg_global_supportcenter@al-enterprise.com
OmniSwitch AOS Release 6 Transceivers Guide November 2018 ii

Contents
About This Guide .......................................................................................................... iv

Supported Platforms .......................................................................................................... iv
Who Should Read this Manual? ......................................................................................... v
When Should I Read this Manual? ..................................................................................... v
What is Not in this Manual? ............................................................................................... v
How is the Information Organized? ................................................................................... v
Documentation Roadmap .................................................................................................. vi
Related Documentation .................................................................................................... vii
Product Documentation ...................................................................................................viii
Technical Support ...........................................................................................................viii
Chapter 1 Small Form-Factor Pluggables (SFPs) ................................................................... 1-1

In This Chapter ................................................................................................................1-1
SFP MSA Specification ..................................................................................................1-2
SFP Transceiver Installation and Removal .....................................................................1-3
Gigabit Ethernet Transceivers .........................................................................................1-5
100 Mbit Ethernet Transceivers ....................................................................................1-11
Dual-Speed Ethernet Transceivers ................................................................................1-14
10-Gigabit SFP+ Transceivers ......................................................................................1-16
Chapter 2 Transceiver Compatibility Matrix ......................................................................... 1-21

OmniSwitch 6350 ..........................................................................................................1-22
OmniSwitch 6450 ..........................................................................................................1-24
OmniSwitch AOS Release 6 Transceivers Guide November 2018 iii

About This Guide
This OmniSwitch Transceivers Guide provides specifications and compatibility information on the
supported transceivers for the OmniSwitch 6350 and OmniSwitch 6450.
Supported Platforms
The information in this guide applies to the following products:
• OmniSwitch 6350
• OmniSwitch 6450
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page iv

About This Guide Who Should Read this Manual?
Who Should Read this Manual?

The audience for this user guide is network administrators and IT support personnel who need to provide
network connectivity using transceivers on an OmniSwitch.
When Should I Read this Manual?

Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are
ready to provide connectivity using the supported transceivers. You should have already stepped through
the first login procedures and read the brief software overviews in the appropriate OmniSwitch AOS
Release 6 Hardware Guide.
This guide includes information about the supported OmniSwitch transceivers.
• Transceiver specifications
• Transceiver compatibility information
What is Not in this Manual?

Procedures for switch management methods, such as CLI, web-based (WebView or OmniVista) or SNMP,
are outside the scope of this guide.
For information on WebView and SNMP switch management methods consult the OmniSwitch AOS
Release 6 Switch Management Guide. Information on using WebView and OmniVista can be found in the
context-sensitive on-line help available with those network management applications.
This guide is designed to provide transceiver specification and compatibility information only and is not
intended as a reference for any CLI commands or configuration information. Refer to the Documentation
Roadmap for a list of available user guides.
How is the Information Organized?

Chapters in this guide are broken down by transceiver type. Additional sub-sections are provided for the
various types of transceivers.
Specification Information. Each transceiver has an associated table providing individual specifications
for all supported transceivers.
Compatibility Information. A compatibility chart is provided for each transceiver specifying which
modules or switch the transceiver is supported on.
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page v

About This Guide Documentation Roadmap
Documentation Roadmap
The OmniSwitch user documentation suite was designed to supply you with information at several critical
junctures of the configuration process. The following section outlines a roadmap of the manuals that will
help you at each stage of the configuration process. Under each stage, we point you to the manual or
manuals that will be most helpful to you.
Stage 1: Using the Switch for the First Time

Pertinent Documentation: Hardware Users Guide
Release Notes
The Hardware Users Guide provides the basic information you need to unpack and identify the compo-
nents of your shipment. It provides information on unpacking the switch, unlocking access control, setting
the switch’s IP address, and setting up a password. It also includes overview information on fundamental
aspects of the switch, such as hardware LEDs, the software directory structure, CLI conventions, and web-
based management.
At this time you should also familiarize yourself with the Release Notes that accompanied your switch.
This document includes important information on feature limitations that are not included in other user
guides.
Stage 2: Gaining Familiarity with Basic Switch Functions

Pertinent Documentation: Hardware Users Guides
Switch Management Guide
OmniSwitch Transceivers Guide
Once you have your switch up and running, you will want to begin investigating basic aspects of its hard-
ware and software. Information about switch hardware is provided in the Hardware Guide. This guide
provide specifications, illustrations, and descriptions of all hardware components, such as chassis, power
supplies, Chassis Management Modules (CMMs), Network Interface (NI) modules, and cooling fans. It
also includes steps for common procedures, such as removing and installing switch components.
The Switch Management Guide is the primary users guide for the basic software features on a single
switch. This guide contains information on the switch directory structure, basic file and directory utilities,
switch access security, SNMP, and web-based management. It is recommended that you read this guide
before connecting your switch to the network.
Stage 3: Integrating the Switch Into a Network

Pertinent Documentation: Network Configuration Guide
When you are ready to connect your switch to the network, you will need to learn how the OmniSwitch
implements fundamental software features, such as 802.1Q, VLANs, Spanning Tree, and network routing
protocols. The Network Configuration Guide contains overview information, procedures, and examples on
how standard networking technologies are configured in the OmniSwitch.
Anytime
The OmniSwitch CLI Reference Guide contains comprehensive information on all CLI commands
supported by the switch. This guide includes syntax, default, usage, example, related CLI command, and
CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can
be consulted anytime during the configuration process to find detailed and specific information on each
CLI command.
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page vi

About This Guide Related Documentation
Related Documentation
The following are the titles and descriptions of all the related the OmniSwitch user manuals:
• OmniSwitch 6350 Hardware Users Guide
• Detailed technical specifications and procedures for the chassis and components. Also includes
comprehensive information on assembling and managing stacked configurations.
• OmniSwitch 6450 Hardware Users Guide
Detailed technical specifications and procedures for the chassis and components. Also includes
comprehensive information on assembling and managing stacked configurations.
• OmniSwitch AOS Release 6 CLI Reference Guide
Complete reference to all CLI commands supported on the OmniSwitch Series switches. Includes
syntax definitions, default values, examples, usage guidelines and CLI-to-MIB variable mappings.
• OmniSwitch AOS Release 6 Switch Management Guide
Includes procedures for readying an individual switch for integration into a network. Topics include
the software directory architecture, image rollback protections, authenticated switch access, managing
switch files, system configuration, using SNMP, and using web management software (WebView).
• OmniSwitch AOS Release 6 Network Configuration Guide
Includes network configuration procedures and descriptive information on all the major software
features and protocols included in the base software package. Chapters cover Layer 2 information
(Ethernet and VLAN configuration), Layer 3 information (routing protocols, such as RIP), security
options (authenticated VLANs), Quality of Service (QoS), and link aggregation.
• OmniSwitch AOS Release 6 Transceivers Guide
Includes transceiver specifications and product compatibility information.

• Technical Tips, Field Notices
Includes information published by Alcatel-Lucent’s Customer Support group.

• Release Notes
Includes critical open Problem Reports, feature exceptions, and other important information on the
features supported in the current release and any limitations to their support.
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page vii

About This Guide Product Documentation
Product Documentation
All products are shipped with a Product Documentation Card that provides details for downloading docu-
mentation for all OmniSwitch and other Alcatel-Lucent data enterprise products. All user guides for the
OmniSwitch Series are included on the Alcatel-Lucent public website. This website also includes user
guides for other Alcatel-Lucent Enterprise products. The latest user guides can be found on our website at:
businessportal2.alcatel-lucent.com
Technical Support
An Alcatel-Lucent Enterprise service agreement brings your company the assurance of 7x24 no-excuses
technical support. You will also receive regular software updates to maintain and maximize your Alcatel-
Lucent product’s features and functionality and on-site hardware replacement through our global network
of highly qualified service delivery partners. Additionally, with 24-hour-a-day access to Alcatel-Lucent’s
Service and Support web page, you’ll be able to view and update any case (open or closed) that you have
reported to Alcatel-Lucent’s technical support, open a new case or access helpful release notes, technical
bulletins, and manuals.
For more information on Alcatel-Lucent-Lucent Enterprise Service Programs:

Web: businessportal2.alcatel-lucent.com
Email: ebg_global_supportcenter@al-enterprise.com.
Phone:
North America: 800-995-2696
Latin America: 877-919-9526
EMEA: +800 00200100 (Toll Free) or +1(650) 385-2193
Asia Pacific: +65 6240 8484
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page viii

1 Small Form-Factor
Pluggables (SFPs)
OmniSwitch switches use both copper-based and fiber-based optical Small Form Factor Pluggable (SFP)
transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applica-
tions. Copper-based and fiber-based optical SFPs can be mixed on the same module.
In This Chapter
This chapter describes the technical specifications for all the OmniSwitch supported SFP transceivers. For
additional details about OmniSwitch modules, see the appropriate OmniSwitch Hardware Guide.
Transceiver specifications in this chapter include:
• SFP MSA Specifications. See “SFP MSA Specification” on page 1-2
• SFP Transceiver Installation. See “SFP Transceiver Installation and Removal” on page 1-3
• Gigabit Ethernet Transceivers. See “Gigabit Ethernet Transceivers” on page 1-5.
• 100 Mbit Ethernet Transceivers. See “100 Mbit Ethernet Transceivers” on page 1-11.
• Dual-Speed Ethernet Transceivers. See “Dual-Speed Ethernet Transceivers” on page 1-14.
• 10-Gigabit SFP+ Transceivers. See “10-Gigabit SFP+ Transceivers” on page 1-16
For information on installing and managing OmniSwitch hardware, see the appropriate Hardware Users
Guide.
For information on OmniSwitch SFP compatibility, see “Transceiver Compatibility Matrix” on page 2-22.
OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-1

Small Form-Factor Pluggables (SFPs) SFP MSA Specification
SFP MSA Specification

The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common
interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP
housing cage. The connector provides the interface for the hot pluggable SFP module. Each SFP module
contains a serial interface to provide identification information that describes the SFP capabilities, stand
interfaces, manufacturer and other information.
For information on installing SFPs, refer to the documentation included with the transceiver.
This diagram is a representation

only; the physical appearance of the
actual module may vary slightly.
Small Form Factor Pluggable (SFP)

Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal
SFP Transceiver Installation and Removal

Follow the instructions below for the appropriate SFP type.
ESD Caution: Before handling the module, you must discharge all static electricity on your person to
avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches
your skin. Attach the other end of the strap to the chassis. If your chassis provides a grounding lug, this
can be used. Refer to your Hardware Users Guide for details.
If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the
chassis. If your chassis provides a grounding lug, this can be used. Refer to your Hardware Users Guide
for details.
Dust Exposure: To reduce the risk of dust exposure and physical damage, be sure to replace the protec-
tive rubber cover (provided) when the SFP is not in use.
Eye Safety: SFP transceivers are international Class 1 laser products and are eye-safe devices when oper-
ated within the limits of manufacturers’ specifications. Operating SFP transceivers in a manner inconsis-
tent with intended usage and specification may result in hazardous radiation exposure.
Note: After removing a transceiver, wait for a minimum of 5 seconds before re-inserting any transceiver
into the same port. This allows sufficient time for software to detect the removal of the transceiver. Never
force the transceiver in or out of the transceiver slot.
To remove, you must first open the SFP’s hinged face to approximately ninety
degrees. Then, grasp the hinged face and carefully pull the SFP straight out of
Interface Slot the slot.
When inserting a SFP, be sure that the hinged face is closed. Slide the SFP
straight into the slot until the module clicks firmly into place.
SFP Module
SFP - Hinged

Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal
To install, align the transceiver with the transceiver slot on the

NI module, as shown. Be sure that the bail wire delatch is in the
up, or closed position. Slide the transceiver straight into the slot
until the module clicks firmly into place.
To remove, you must first pull down on the bail

wire delatch. Grip the wire delatch while it is in this
open position and carefully pull the transceiver
straight out of the slot. SFP Transceiver
Transceiver Slot
Bail Wire Delatch
(Shown in open “removal” posi-
tion; when inserting, bail Network Interface (NI)

delatch must be closed.) Module
SFP - Bail Wire
To install, align the transceiver with the Network Interface (NI) Module
transceiver slot on the NI module, as
shown. Carefully slide the transceiver
back until it clicks into place; this is an
indication that the connectors are firmly SFP Transceiver
seated.
To remove, use the ejector tool (provided

with each switch chassis) to push the trans-
ceiver’s ejector button. The ejector button is
located just below the transceiver port; refer
to the diagram for more information. The
transceiver will disengage from the connec-
Transceiver Slot
tors and eject slightly. Once disengaged, use
the clip end of the ejector tool to carefully
pull the transceiver straight out and away Ejector
from the NI module.
Dust Cover
SFP - Ejector Button

Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers
Gigabit Ethernet Transceivers

SFP-GIG-SX
Gigabit SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, SFP MSA
Connections Supported 1000Base-SX
Fiber Type MMF
Wavelength 850 nm
Optical Power Output -9.5 to -4 dBm
Receiver Sensitivity -17 dBm
Transmission Distance ~275 m on 62.5/125µm
~550 m on 50/125µm
Operating Temperature 0 ºC to 70 ºC
Digital Diagnostic Monitoring Supported (Alcatel-Lucent branded transceivers only)
SFP-GIG-LX
Connector types LC
Standards supported 802.3z, SFP MSA
Connections supported 1000Base-LX
Fiber Type SMF
Wavelength 1310 nm
Optical Power Output -9.5 to -3 dBm
Transmission Distance 10 km
Operating Temperature -40 ºC to 85 ºC / 0 ºC to 70 ºC
Digital Diagnostic Monitoring Supported (Alcatel-Lucent branded transceivers only)
SFP-GIG-LH40
Connector Type LC
Connections Supported 1000Base-LH40
Fiber Type SMF

SFP-GIG-LH40
Wavelength 1310 nm
Optical Power Output -2 to +3 dBm
Reciever Sensitivity -22 dBm
Transmission Distance ~40 km
Digital Diagnostic Monitoring Supported
SFP-GIG-LH70
Connector Type LC
Connections Supported 1000Base-LH70
Fiber Type SMF
Wavelength 1550 nm
Optical Power Output 0 to +5 dBm
SFP-GIG-EXTND
Connector Type LC
Standards Supported 802.3, SFP MSA
Connections Supported -
Fiber Type MMF
Wavelength 1310 nm
Saturation Power Output 0 dBm

SFP-GIG-T
Gigabit SFP Copper Transceiver.
Connector Type RJ-45
Connections supported 10/100/1000Base-T
Cable Type CAT5, CAT5e, CAT6
Transmission Distance 100 m
Digital Diagnostic Monitoring Not Supported
SFP-GIG-BX-D
Bi-Directional SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3ah, SFP MSA
Connections Supported 1000Base-BX10
Fiber Type SMF
Wavelength Transmit: 1490 mm
Receive: 1310 nm
Average Power Output -9 to -3 dBm
Receiver Sensitivity -19.5 dBm
Notes Designed for use with SFP-GIG-BX-U
SFP-GIG-BX-U
Connector Type LC
Fiber Type SMF
Wavelength Transmit: 1310 nm
Receive: 1490 nm

SFP-GIG-BX-U
Notes Designed for use with SFP-GIG-BX-D
SFP-GIG-BX-D20
Connector Type LC
Fiber Type SMF
Receive: 1310 nm
Operating Temperature -5ºC to 70ºC
Notes Designed for use with SFP-GIG-BX-U20
SFP-GIG-BX-U20
Connector Type LC
Fiber Type SMF
Receive: 1490 nm
Notes Designed for use with SFP-GIG-BX-D20

SFP-GIG-BX-D40
Connector Type LC
Fiber Type SMF
Receive: 1310 nm
Average Power Output -2 to +3 dBm
Notes Designed for use with SFP-GIG-BX-U40
SFP-GIG-BX-U40
Connector Type LC
Fiber Type SMF
Receive: 1490 nm
Average Power Output -2 to +3 dBm
Notes Designed for use with SFP-GIG-BX-D20
SFP-GIG-CWD
Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber
over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications.
Connector Type LC

SFP-GIG-CWD
Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber
over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications.
Connections Supported 1000Base-LX
Fiber Type SMF
Wavelength 1470, 1490, 1510, 1530, 1550, 1570, 1590, 1610
Optical Power Output -2 to +3 dBm
Transmission Distances ~62 km
Operating Temperature -5 ºC to 70 ºC

Small Form-Factor Pluggables (SFPs) 100 Mbit Ethernet Transceivers
100 Mbit Ethernet Transceivers

SFP-100-BX20LT
Connector Type SC
Standards Supported 802.3ah, SFP MSA, ITU-T G.983
Connections Supported 100Base-BX
Fiber Type SMF
Receive: 1310 nm
Notes Designed for use with SFP-100-BX20NU
SFP-100-BX20NU
Connector Type SC
Fiber Type SMF
Receive: 1550 nm
Notes Designed for use with SFP-100-BX20LT

SFP-100-BXLC-D
Connector Type LC
Fiber Type SMF
Receive: 1310 nm
Notes Designed for use with SFP-100-BXLC-U
SFP-100-BXLC-U
Connector Type LC
Fiber Type SMF
Receive: 1550 nm
Notes Designed for use with SFP-100-BXLC-D
SFP-100-LC-MM
SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3u, SFP MSA
Connections supported 100Base-FX

SFP-100-LC-MM
Fiber Type MMF
Wavelength 1310 nm
Optical Power Output -19 to -14 dBm on 62.5/125µm
-22 to -14 dBm on 50/125µm
Transmission Distance ~2 km on 62.5/125µm
~2 km on 50/125µm
SFP-100-LC-SM15
Connector Type LC
Connections Supported 100Base-FX
Fiber Type SMF
Wavelength (nm) 1310 nm
Optical Power Output -15 to -8 dBm
SFP-100-LC-SM40
Connector Type LC
Connections Supported 100Base-FX
Fiber Type SMF
Wavelength 1310 nm
Optical Power Output -15 to -8 dBm
Transmission Distances ~40 km

Small Form-Factor Pluggables (SFPs) Dual-Speed Ethernet Transceivers
Dual-Speed Ethernet Transceivers

SFP-DUAL-BX-D
Dual-Speed Bi-Directional SFP Optical Transceiver.
Connector Type LC
Connections Supported 1000BASE-BX10-D
Fiber Type SMF
Receive: 1310 nm
Transmission Distance ~ 10 km
SFP-DUAL-BX-U
Dual-Speed Bi-Directional SFP Optical Transceiver.
Connector Type LC
Connections Supported 1000BASE-BX10-U
Fiber Type SMF
Receive: 1550 nm
Transmission Distances ~ 10 km
SFP-DUAL-SM10
Dual-Speed SFP Optical Transceiver.
Connector Type LC
Standards Supported 802.3z, 802.3ah, SFP MSA
Connections Supported 100Base-LX, 1000Base-LX
Fiber Type SMF

Small Form-Factor Pluggables (SFPs) Dual-Speed Ethernet Transceivers
SFP-DUAL-SM10
Dual-Speed SFP Optical Transceiver.
Wavelength 1310 nm
Average Power Output 100Base-LX: -15 to -8 dBm
1000Base-LX: -9.5 to -3 dBm
Receiver Sensitivity 100Base-LX: -28
1000Base-LX: -22
Transmission Distances 10 km
Operating Temperature 0ºC to 70ºC
Notes: Transceiver may take between 10 and 20 seconds to initialize when first
inserted.

Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers
10-Gigabit SFP+ Transceivers
SFP-10G-SR
10-Gigabit SFP+ Optical Transceiver.
Connector Type LC
Standards Supported 802.3 Clause 52
Connections supported 10GBase-SR
Fiber Type MMF
Wavelength 850 nm
Optical Power Output -7.3 to -1.3 dBm
Transmission Distance ~ 300 m
Operating Temperature 0 ºC to 70ºC
SFP-10G-LR
Connector Type LC
Standards Supported 802.3 Clause 52
Connections supported 10GBase-LR
Fiber Type SMF
Wavelength 1310 nm
Optical Power Output -8.2 to 0.5 dBm
SFP-10G-ER
Connector Type LC
Standards Supported 802.3ae
Connections supported 10GBase-E
Fiber Type SMF

SFP-10G-ER
Wavelength 1550 nm
Optical Power Output -4.7 to 4.0 dBm
SFP-10G-ZR
Connector Type LC
Connections supported 10GBase-ZR
Fiber Type SMF
Wavelength 1550 nm
Optical Power Output 0 to 5.0 dBm
Operating Temperature -5 ºC to 70 ºC

SFP-10G-LRM
Connector Type LC
Standards Supported 802.3aq
Connections supported 10GBase-LRM
Fiber Type MMF
Wavelength 1310 nm
Optical Power Output -6.5 to .5 dBm
Transmission Distance ~ 220 m
SFP-10G-GIG-SR
Connector Type LC
Standards Supported 802.3-2005
Connections supported 10GBase-SR/SW, 1000Base-SX
Fiber Type MMF
Wavelength 850 nm
Optical Power Output -5 to -1 @ 10G
-9.5 to -1dBm @ 1G
Receiver Sensitivity -11.1 dBm @ 10G
-17 dBm @ 1G
Transmission Distance OM1: ~33m @ 10G, ~275m @ 1G
OM2: ~82m @ 10G, ~550m @ 1G
OM3: ~300m @ 10G, ~550m @ 1G
Maximum Power Consumption <1.0 Watt

SFP-10G-T
10-Gigabit SFP+ Copper Transceiver.
Connector Type RJ-45
Standards Supported 802.3az
Connections supported 10GBaseT
Cable Type CAT6a/7
Transmission Distance 30 m
SFP-10G-C
Connector Type Direct Attached
Cable Length 60cm, 1m, 3m, 7m
Wire Gauge 24AWG
Bend Radius 1.25 in.
OS6450S-CBL-60, OS6450S-C60-S
Cable Length 60cm
Wire Gauge 24AWG
OS6450S-CBL-1M, OS6450S-C1M-S
Cable Length 1m
Wire Gauge 24AWG

OS6450S-CBL-1M, OS6450S-C1M-S
OS6450-CBL-3M
Cable Length 3m
Wire Gauge 24AWG
OS6450-CBL-7M
Cable Length 7m
Wire Gauge 24AWG
OS6350-CBL-60CM
Cable Length 60cm
Wire Gauge 24AWG

OS6350-CBL-1M
Cable Length 1m
Wire Gauge 24AWG
OS6350-CBL-3M
Cable Length 3m
Wire Gauge 24AWG
OS6350-CBL-7M
Cable Length 7m
Wire Gauge 24AWG

Transceiver Compatibility Matrix 10-Gigabit SFP+ Transceivers
2 Transceiver Compatibility
Matrix

Transceiver Compatibility Matrix OmniSwitch 6350
OmniSwitch 6350
The following table shows the supported transceivers and the minimum release required for support on the
OmniSwitch 6350:
SFP OS6350
SFP-GIG-SX 6.7.1
SFP-GIG-LX 6.7.1
SFP-GIG-LH40 6.7.1
SFP-GIG-LH70 6.7.1
SFP-GIG-EXTND 6.7.1
SFP-GIG-T1 6.7.1
SFP-GIG-BX-D Not supported
SFP-GIG-BX-U Not supported
SFP-GIG-BX-D20 Not supported
SFP-GIG-BX-U20 Not supported
SFP-GIG-BX-D40 Not supported
SFP-GIG-BX-U40 Not supported
SFP-GIG-CWD Not supported
SFP-100-BX20LT Not supported
SFP-100-BX20NU Not supported
SFP-100-BXLC-D Not supported
SFP-100-BXLC-U Not supported
SFP-100-LC-MM Not supported
SFP-100-LC-SM15 Not supported
SFP-100-LC-SM40 Not supported
SFP-DUAL-BX-D Not supported
SFP-DUAL-BX-U Not supported
SFP-DUAL-SM10 Not supported
SFP-10G-SR Not supported
SFP-10G-LR Not supported
SFP-10G-ER Not supported
SFP-10G-ZR Not supported
SFP-10G-LRM Not supported
SFP-10G-T Not supported
SFP-10G-C 6.7.1
OS6350-CBL-60CM 6.7.1.R04
OS6350-CBL-1M 6.7.1.R04

SFP OS6350
OS6350-CBL-3M 6.7.1.R04
OS6350-CBL-7M 6.7.1.R04
SFP-10G-GIG-SR Not supported
1
Supports 1G only.

OmniSwitch 6450
The following table shows the supported transceiver configurations and the minimum release required for
support on the OmniSwitch 6450:
SFP OS6450 OS6450-M/X OS6450-P10S/

U24S
SFP-GIG-SX 6.6.3 6.6.5 6.6.5
SFP-GIG-LX 6.6.3 6.6.5 6.6.5
SFP-GIG-LH40 6.6.3 6.6.5 6.6.5
SFP-GIG-LH70 6.6.3 6.6.5 6.6.5
SFP-GIG-EXTND 6.6.4 6.6.5 6.6.5
SFP-GIG-T1 6.6.3 6.6.5 6.6.5
SFP-GIG-BX-D 6.6.3 6.6.5 6.6.5
SFP-GIG-BX-U 6.6.3 6.6.5 6.6.5
SFP-GIG-BX-D20 6.6.4 6.6.5 6.6.5
SFP-GIG-BX-U20 6.6.4 6.6.5 6.6.5
SFP-GIG-BX-D40 6.6.4 6.6.5 6.6.5
SFP-GIG-BX-U40 6.6.4 6.6.5 6.6.5
SFP-GIG-CWD 6.6.3 6.6.5 6.6.5
SFP-100-BX20LT2 6.6.3 6.6.5 6.6.5
2
SFP-100-BX20NU 6.6.3 6.6.5 6.6.5
2
SFP-100-BXLC-D 6.6.3 6.6.5 6.6.5
2
SFP-100-BXLC-U 6.6.3 6.6.5 6.6.5
2
SFP-100-LC-MM 6.6.3 6.6.5 6.6.5
SFP-100-LC-SM152 6.6.3 6.6.5 6.6.5
2
SFP-100-LC-SM40 6.6.3 6.6.5 6.6.5
SFP-DUAL-BX-D 6.6.3 6.6.5 6.6.5
SFP-DUAL-BX-U 6.6.3 6.6.5 6.6.5
SFP-DUAL-SM10 6.6.4 6.6.5 6.6.5
SFP-10G-SR 6.6.3 6.6.5 6.6.5
SFP-10G-LR 6.6.3 6.6.5 6.6.5
SFP-10G-ER 6.6.3 6.6.5 6.6.5
SFP-10G-ZR 6.7.2.R05 6.7.2.R05 6.7.2.R05
SFP-10G-LRM 6.6.3 6.6.5 6.6.5
3
SFP-10G-GIG-SR 6.6.4 6.6.5 6.6.5
SFP-10G-T 6.7.1.R04 6.7.1.R04 6.7.1.R04
SFP-10G-C 6.6.3 6.6.5 6.6.5

SFP OS6450 OS6450-M/X OS6450-P10S/

U24S
OS6450S-CBL-60, 6.6.3 6.6.5 6.6.5
OS6450S-C60-S
OS6450S-CBL-1M, 6.6.3 6.6.5 6.6.5
OS6450S-C1M-S
OS6450-CBL-3M 6.6.3 6.6.5 6.6.5
OS6450-CBL-7M 6.6.3 6.6.5 6.6.5
1.
6450-U24(S) supports 10/100/1000 mbps on user ports only (1-22), SFP+ ports support 1G only. Not
supported on combo ports.
2
Supported on 6450-U24(S) user ports and combo ports. Not supported on 1G/10G uplink ports or
expansion modules.
3
Supports 1G/10G speeds on 10G SFP+ ports only. Transceiver not supported on 1G SFP ports.

Omniswitch Aos Release 6 Transceivers Guide: 060568-10 Rev. A November 2018

Uploaded by

Copyright:

Available Formats

Omniswitch Aos Release 6 Transceivers Guide: 060568-10 Rev. A November 2018

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omniswitch Aos Release 6 Transceivers Guide: 060568-10 Rev. A November 2018

Uploaded by

Copyright:

Available Formats

060568-10 Rev.

OmniSwitch AOS Release 6

OmniSwitch AOS Release 6 Transceivers Guide November 2018 i

26801 West Agoura Road

Service & Support Contact Information

OmniSwitch AOS Release 6 Transceivers Guide November 2018 ii

About This Guide .......................................................................................................... iv

Chapter 1 Small Form-Factor Pluggables (SFPs) ................................................................... 1-1

Chapter 2 Transceiver Compatibility Matrix ......................................................................... 1-21

OmniSwitch AOS Release 6 Transceivers Guide November 2018 iii

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page iv

Who Should Read this Manual?

When Should I Read this Manual?

• Transceiver compatibility information

What is Not in this Manual?

How is the Information Organized?

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page v

Stage 1: Using the Switch for the First Time

Stage 2: Gaining Familiarity with Basic Switch Functions

Stage 3: Integrating the Switch Into a Network

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page vi

Includes transceiver specifications and product compatibility information.

Includes information published by Alcatel-Lucent’s Customer Support group.

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page vii

For more information on Alcatel-Lucent-Lucent Enterprise Service Programs:

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page viii

• Gigabit Ethernet Transceivers. See “Gigabit Ethernet Transceivers” on page 1-5.

• Dual-Speed Ethernet Transceivers. See “Dual-Speed Ethernet Transceivers” on page 1-14.

• 10-Gigabit SFP+ Transceivers. See “10-Gigabit SFP+ Transceivers” on page 1-16

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-1

SFP MSA Specification

This diagram is a representation

Small Form Factor Pluggable (SFP)

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-2

SFP Transceiver Installation and Removal

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-3

To install, align the transceiver with the transceiver slot on the

To remove, you must first pull down on the bail

(Shown in open “removal” posi-

tion; when inserting, bail Network Interface (NI)

SFP - Bail Wire

To remove, use the ejector tool (provided

SFP - Ejector Button

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-4

Gigabit Ethernet Transceivers

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-5

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-6

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-7

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-8

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-9

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-10

100 Mbit Ethernet Transceivers

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-11

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-12

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-13

Dual-Speed Ethernet Transceivers

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-14

OmniSwitch AOS Release 6 Transceivers Guide November 2018 page 1-15

10-Gigabit SFP+ Transceivers