International Journal of Chemical, Environmental & Biological Sciences (IJCEBS) Volume 1, Issue 2 (2013) ISSN 2320 –4087 (Online)

Biosorption of Lead (Pb2+) by using

Chlorella vulgaris
Wai Lynn Aung1, Dr. Nway Nay Hlaing2, and Dr. Kyaw Nyein Aye3

implicated in food, cosmetic, aquaculture and pharmaceutical

Abstract—Algae are interested for carbon fixation from green industries [1].
house gas for waste water treatments and it has the high potential for Heavy metals are among the major concerns in wastewater
production of biodiesel. The adsorption of heavy metals onto the treatment. Heavy metals are often derived from heavy industry,
surface of the algae is alternative technique for current wastewater
such as electroplating and battery factories. The treatment of
treatment systems. Thus, this study was conducted to determine the
biosorption characteristic of algae with lead. In this study, the this type of wastewater involves high cost techniques such as ion
cultivation of algae Chlorella vulgaris in closed pond with different exchange, evaporation, precipitation, membrane separation etc.
amount of carbonated water (25, 50, 75, 100, 200 and 300 ml of soda However, these common techniques are too expensive to treat
per 1 L of culture) was studied along the biosorbent collection and low levels of heavy metal in waste water. Therefore a low cost
found that the additional carbonated water shortens the accelerated biosorption process using algae as an adsorbent has lately been
growth phase of the algae cultivation by 24 hours. Algae biomass were
introduced as an alternative [2].
harvested with ferric chloride coagulation and dried at 60°C for 1 day.
Acid treatment of the biosorbent was also conducted with 0.2 M Another issue from burning of fossil fuels is the
H 2 SO 4 (1 L of acid per 1 g of algae biomass). The size of the selected ever-increasing carbon dioxide (CO 2 ) emission, whose trend
algae biosorbent is less than 75 µm. In biosorption, optimum pH of the will continue with the fast pace of modern industry development
adsorption (6, 5, 4, 3) and kinetic experiment for optimum adsorption if a feasible energy source replacement could not be found.
time (5, 15, 30, 90, 180, and 360 mins) were investigated. The Algae, which can assimilate CO 2 photoautotrophically or
resulting samples were analyzed with Atomic Absorption
Spectrophotometer (AAS). The optimum pH for the biosorption is 6
mixtrophically, is a perfect candidate for CO 2 sequestration and
with 99.4% removal efficiency. The kinetic of the biosorption of Pb2+ greenhouse gas reduction. The concept of using wastewater as a
by Chlorella vulgaris followed the pseudo-second order model. The medium and source of nutrients for algae production has the
values of parameters k 2 , q e and correlation coefficient R2 were benefit of serving both environmental and energy-related needs.
0.186×10-3, 250 mg/g and 0.997 respectively. The initial Pb Compared to the conventional wastewater treatment process,
concentration also varied 51.79, 103.59, 207.19, 310.78 and 414.38 which introduces activated sludge, a biological floc, to degrade
mg/L for determination of the adsorption isotherm of heavy metal on
algae. The biosorption isotherm of lead on C. vulgaris follows
organic carbonaceous matter to CO 2 , algae can assimilate
Langmuir isotherm model. organic pollutants into cellular constituents such as lipid and
carbohydrate, thus achieving pollutant reduction in a more
Keywords—algae cultivation, biosorption, chlorella vulgaris, environment-friendly way [3].
heavy metal, lead removal. Metal pollution is one of the most important environmental
problems today. Three kinds of metals are of concern, including
I. INTRODUCTION toxic metals (such as Hg, Cr, Pb, Zn, Cu, Ni, Cd, As, Co, Sn
etc.), precious metals (such as Pd, Pt, Ag, Au, Ru etc.) and
M ICROALGAE, which means including prokaryotic
photosynthetic microorganisms such as cyanobacteria,
are organisms that play a key role in aquatic ecosystems. It is
radionuclide (such as U, Th, Ra, Am, etc.) Metals can be
distinguished from other toxic pollutants, since are
estimated that around 40% of global photosynthesis is non-biodegradable and can accumulate in the living tissues, thus
performed by microalgae. Microalgae form the basis of most of becoming concentrated throughout the food chain [4]. This
trophic aquatic chain. The use of microalgae in biotechnology work is to study the removal efficiency of lead from water by the
has been increased in recent years, these organisms being algae Chlorella vulgaris. The most common sources of lead are
lead-based paint, contaminated soil, household dust, drinking
water, lead-glazed pottery and the effluents of industrial
1
Wai Lynn Aung, is student of Yangon Technological University, Yangon, wastewaters.
Myanmar (phone: 0951224743; e-mail: wailynnaung@gmail.com).
2 Using algae for wastewater treatment offers some interesting
Dr. Nway Nay Hlaing, is associate professor of Department of Chemical
Engineering, Yangon Technological University, Yangon, Myanmar (e-mail: advantages over conventional wastewater treatment.
nway.nay5@gmail.com). Advantages of algae wastewater treatment are:
3
Dr. Kyaw Nyein Aye, is visiting professor of Department of Chemical
• Cost effective
Engineering, Yangon Technological University, Yangon, Myanmar. He is also
visiting professor of Department of Chemical Engineering, Mandalay • Low energy requirement
Technological University, Mandalay, Myanmar (e-mail: kyawnyeinaye • Reductions in sludge formation
@gmail.com).

408
 International Journal of Chemical, Environmental & Biological Sciences (IJCEBS) Volume 1, Issue 2 (2013) ISSN 2320 –4087 (Online)

• Green house gas emission reduction E. Kinetic Experiment

• Production of useful algal biomass [5]. Kinetic studies provide information relating to time required
Biosorption is a physiochemical process that occurs for the establishment of sorption equilibrium. They also give
naturally in certain biomass which allows it to passively information about the reactant species that govern the rate of the
concentrate and bind contaminants onto its cellular structure. reaction and up to what order. Various models can describe the
Though using biomass in environmental cleanup has been in transient behavior of a batch adsorption process. Most of these
practice for a while, scientists and engineers are hoping this have been reported as pseudo-first-order and some as
phenomenon will provide an economical alternative for pseudo-second- order kinetic processes.
removing toxic heavy metals from industrial wastewater and Kinetic experiments were performed in continuously stirred
aid in environmental remediation. beakers containing 500 ml metal solutions at initial
concentrations 207.2 mg/L and 0.5 g of biosorbent at room
II. EXPERIMENTAL METHODS temperature (around 30°C). Samples of 50 ml solution were
withdrawn at scheduled time intervals and analyzed for residual
A. Cultivation of Algae Pb concentration by the Atomic Absorption Spectroscopy
Chlorella vulgaris in lag phase used in the experiments was (AAS).
inoculated in Cornway Medium. It was cultivated outdoors in
growth media containing ammonium sulfate NH 4 SO 4 (0.16 g/l), F. Biosorption Isotherm
Urea CO(NH 2 ) 2 (0.016 g/l), T-super P 2 O 5 (0.016 g/l) made up To determine the adsorption isotherm, the initial
in tap water. The pH was maintained near 5.5 with aeration. concentration of the metal solution must be varied at a constant
The first inoculation was done in 3 flat bottomed flasks (1 L). contact time. For equilibrium studies, the concentrations of Pb
Then it was transferred to two 5 L plastic bottles. When the solutions will be varied from 51.79 to 414.38 mg/L and
desired density of algae was reached, the algae from 2 bottles biosorbent dosage was 2 g/L. The pH will adjust to 6.0 using
were cultivated in the 40 L glass tank. The algae were cultured H 2 SO 4 or NaOH hourly throughout the experiment. The
for 1 week per batch. The cells were harvested by coagulation mixtures will be agitated on a magnetic stirrer for 6 hr at
with ferric chloride and filtration. constant temperature and then set still 12 hr. Then the
B. Effect of Carbonated water concentration on Cultivation biosorbent will be filtered through an acid-cleaned filter paper.
During cultivation of algae, CO 2 is needed for the III. RESULTS AND DISCUSSIONS
photosynthesis process of the algae. The effect of the
carbonated water (soda) concentration cultivation of Chlorella For the effect of the carbonated water concentration on
vulgaris was also determined. The amount of the carbonated cultivation of Chlorella vulgaris, the resulting growth curves
water was varied from 0 to 300 ml. The other nutrients were are as shown in Fig. 1 and Fig. 2 according to the initial
same as above cultivation. The samples were taken out daily and concentration of the algae (0.95 and 1.25 × 109 cells
counted the cells numbers with Neubauer hemocytometer on the respectively).
microscope.
C. Preparation of Biosorbent
The harvested biomass was extensively washed two times
with water (1 L of de-ionized water per 1 g of biomass) to get rid
of medium remnants. Then it was dried in the oven (at 60°C)
overnight and pulverized. Acid pre-treatment was then done by
washing the sorbent with 0.2 M solution of H 2 SO 4 (1 L of acid
per 1 g of biomass for 90 minutes), washing twice again by
de-ionized water, filtering with filter paper and drying 24 hours
at constant temperature of 60°C. After drying, the algae biomass
was pulverized and separated the different sizes of algae by
sieves shaker.
D.Determination of Effect of pH on Lead Biosorption
Fig. 1 The Algae Growth Curves with and without High Carbonated
A series of experiments, with 207.2 mg/L (1 mmol/L) Pb Water
solutions, were conducted under different pH to investigate the
effect of pH on the adsorption. The pH was first adjusted to a According to the curves in Fig. 1, the cultures of without
designed value, from 3.0 to 6.0 with H 2 SO 4 or NaOH. Then it additional CO 2 and with 100 ml of additional CO 2 give similar
was measured hourly and maintained steady throughout the growth curve and the higher carbonated water concentrations on
experiment. The resulting solution was analyzed with Atomic cultivation give unfavourable growth curve because of the
Absorption Spectroscopy, AAS, at Universities’ Research inhibition effect on algae growth. The lag phase and accelerated
Centre, University of Yangon. growth phase is found in day 1 and 2. The exponential growth

409
 International Journal of Chemical, Environmental & Biological Sciences (IJCEBS) Volume 1, Issue 2 (2013) ISSN 2320 –4087 (Online)

phase is from day 2 to 7. In day 8, it shows the decelerated

growth phase and the stationary phase is day 9 to day 11 or 12.
Then, the death phase is found on day 13 onwards.
In Fig. 2, the lag phase of second batch cultivation is in day 1
and the accelerated growth phase is in day 2 to 3 and found that
the additional carbonated water shortens the accelerated growth
phase of the algae cultivation by 24 hours. The exponential
growth phase is from day 3 to 9 and the decelerated growth
phase was in day 10. The stationary phase is stable only in
culture without soda and it is from day 10 to 13 until the cells are
tend to decrease in death phase. According to the curves, when
lower carbonated water is used, it could help to get the highest
cells faster but no distinct stationary phase is appeared which
can be noted that no additional CO 2 is necessary for optimizing Fig. 3 Pb removal efficiencies by Chlorella vulgaris at different pH
the Chlorella vulgaris cultivation.
According to the analytical data, the optimum pH for the Pb
adsorption is at 6 with 99.4% removal efficiency. In Fig. 3, It is
found that the greater the pH the higher the removal efficiency
of adsorption.

Fig. The Algae Growth Curves with and without Low Carbonated
Water
TABLE I
SCREEN ANALYSIS OF ACID-TREATED ALGAE POWDER
Size Range Weight %
Fig. 4 Adsorption rate of Lead on biosorbent
>300 um 20.74
Biosorption rate is shown in Fig 4. According to the figure,
300 um – 212 um 13.57
the adsorption of lead on the algae biosorbent is fast in first 30
212 um – 150 um 12.44 mins and the rate is then slow as approching the equilibrium.
150 um – 100 um 10.87 A number of models have been developed to describe the
kinetics of heavy metal biosorption. The pseudo-second order
100 um – 75 um 10.16
kinetic model based on the sorption capacity of solid phase can
<75 um 32.21 be used in this case assuming that measured concentrations are
equal to cell surface concentrations. The pseudo-second order
Screen analysis of the acid-treated algae powder is shown in kinetic rate equation is expressed as:
Table I. In adsorption process, the smaller particle size (1)
adsorbent is attractive because it can give larger internal surface
area for good adsorption. So, the particle size of less than 75 µm Integrating for the boundary condition conditions q t = 0 at t =
of acid-treated algae powder was use as biosorbent. 0 and q t at time t, the form of linearization of pseudo-second
order model is obtained:
(2)

where k 2 is the second order biosorption rate constants (g/mg

min−1), q e and q t are the amounts of adsorbed metal ions on the
biosorbent at the equilibrium and at any time t, respectively. The

410
 International Journal of Chemical, Environmental & Biological Sciences (IJCEBS) Volume 1, Issue 2 (2013) ISSN 2320 –4087 (Online)

kinetic data was analyzed in term of the pseudo-second order.

Fig. 5 Plot of linearization of pseudo-second order model

The plots of t/q t versus t is shown in Fig. 5. The values of
parameters k 2 , q e and correlation coefficient R2 were
0.186×10-3, 250 mg/g and 0.997 respectively. So, it is suggested
that the sorption of Pb2+ onto Chlorella vulgaris followed the
pseudo-second order model very well.
Fig. 6 Isotherms of Lead Biosorption
The capacity of an adsorbent can be described by equilibrium
sorption isotherm, which is characterized by certain constants The biosorption isotherm of Pb2+ by C. vulgaris was
whose values express the surface properties and affinity of the compared with Langmuir and Freundlich isotherm models, as
adsorbent. The Langmuir isotherm is probably the most widely shown in Fig. 6. The plot of linearization of the two models are
applied adsorption isotherm. A basic assumption of this model shown in the Fig. 7 and Fig. 8.
is that adsorption takes place at specific homogeneous sites
within the adsorbent. It is based on the assumption that all the
adsorption sites have equal affinity for molecules of the
adsorbate and there is no transmigration of the adsorbate in the
plane of the surface. It is presented by the following equation:
(3)
where q m is the maximum metal uptake capacities (mg/g); q e
is the amounts of the metal ions adsorbed at equilibrium (mg/g);
C e is the equilibrium concentration of metal ions (mg/L); b is
the equilibrium constant. The linear form of the Langmuir
equation is:
(4)

The Freundlich isotherm is an empirical isotherm that can be

Fig. 7 Plot of Linearization of Langmuir Model
used for non-ideal adsorption, which is commonly presented as:
(5)
Where q is the amounts of the metal ions adsorbed, k and n
are empirical constants for each adsorbent-adsorbate pair at a
given temperature. The linear form of the Freundlich equation is
given as:
(6)

Fig. 8 Plot of Linearization of Freundlich Model

411
 International Journal of Chemical, Environmental & Biological Sciences (IJCEBS) Volume 1, Issue 2 (2013) ISSN 2320 –4087 (Online)

According to the R2 value, it can be said the biosorption

isotherm of lead on C. vulgaris is well described as Langmuir
isotherm model.

IV. CONCLUSION
This study indicated that green algae Chlorella vulgaris,
which could cultivate at low cost, can be possible to use as an
efficient biosorbent material for removal of Pb from
wastewater. In cultivation of algae, it is found that the additional
carbonated water shortens the accelerated growth phase of the
algae cultivation by 24 hours, the exponential growth phase was
reached in day 3 – 9 from starting point and cultivation time of 7
days is suitable for large scale cultivation. It was found that no
carbonated water was necessary to optimize the cultivation of
Chlorella vulgaris. The size less than 75 um of the prepared
biosorbent was used in biosorption. The optimum pH for
biosorption is at 6 with the removal efficiency of 99.4 %. The
pseudo-second order kinetic model is suitable for describing the
biosorption. The biosorption isotherm of lead on C. vulgaris is
well described as Langmuir isotherm model.

REFERENCES
[1] I. Moreno-Garrido. Microalgae immobilization: Current techniques and
uses Institute of Marine Sciences of Andalucı´a (CSIC), Campus Rı´o
San Pedro, s/n 11510, Puerto Real, Ca diz, Spain. 2004.
[2] R. Apiratikul, T.F. Marhaba, S. Wattanachira and P. Pavasant.
Biosorption of binary mixtures of heavy metals by green macro alga,
Caulerpa lentillifera. ongklanakarin J. Sci. Technol., 2004, 26(Suppl.
1) : 199-207.
[3] L. Wang & M. Min & Y. Li & P. Chen & Y. Chen & Y. Liu & Y. Wang
& R. Ruan, Cultivation of green algae chlorella sp. in different
wastewaters from municipal wastewater treatment plant, 9 November
2009.
[4] I. Melcakova, T. Ruzovic. Biosorption of zinc from aqueous solution
using algae and plant biomass. Institute of Environmental Engineering,
Faculty of Mining and Geology, Ostrava, Czech Republic. 2006.
[5] Oilgae, Oilgae Guide to Algae-based Wastewater Treatment. C3B,
Anugraha Apartments, 41 Nungambakkam High Road Chennai –
600034, Tamilnadu, India). 6 November 2003.

412