WeldBend Catalog

Carbon Steel Weld Fitting & Weld Flange
Products for Piping Construction
SIXTY-THIRD
EDITION
Printed in U.S.A.
WELDBEND CORPORATION
6600 SOUTH HARLEM AVENUE, ARGO, IL 60501-1930
SALES General Office
TEL: 708/594-1700 TEL: 773/582-3500
FAX: 708/458-0106 FAX: 773/582-7621
www.weldbend.com
info@weldbend.com
orders@weldbend.com
quotes@weldbend.com
customer.service@weldbend.com
Table of Contents
PAGE
WELDBEND…TODAY..................................................................................................................................................................... 6
THE WELDBEND POLICY ............................................................................................................................................................ 21
ORDERING INFORMATION ........................................................................................................................................................ 22
TERMS AND CONDITIONS ........................................................................................................................................................ 23
FITTINGS ......................................................................................................................................................................................... 25
90° ELBOWS — Long Radius [Schedule: STD, XS, 40, 80, 160, XXS] ........................................................... 26
90° ELBOWS — Short Radius [Schedule: STD, XS, 40, 80, 160, XXS] .......................................................... 29
90° REDUCING ELBOWS — [Schedule: STD, XS, 40, 80] ................................................................................... 32
90° ELBOWS — 3R [Schedule: STD, XS, 40, 80] ................................................................................................... 36
45° ELBOWS — Long Radius [Schedule: STD, XS, 40, 80, 160, XXS] ........................................................... 38
45° ELBOWS — 3R [Schedule: STD, XS, 40, 80] ................................................................................................... 41
180° RETURN BENDS — Long Radius [Schedule: STD, XS, 40, 80, 160, XXS] .......................................... 43
180° RETURN BENDS — Short Radius [Schedule: STD, XS, 40, 80, 160, XXS] ......................................... 46
STRAIGHT TEES — [Schedule: STD, XS, 40, 80, 160, XXS] ................................................................................ 49
REDUCING TEES — [Schedule: STD, XS, 40, 80, 160, XXS] ............................................................................... 52
CONCENTRIC AND ECCENTRIC REDUCERS — [Schedule: STD, XS, 40, 80, 160, XXS] ............................ 62
CAPS — [Schedule: STD, XS, 40, 80, 160, XXS] .................................................................................................... 76
LAP JOINT STUB ENDS — [Schedule: STD, XS, 40, 80, 160, XXS]................................................................... 79
BOX QUANTITIES ........................................................................................................................................................... 82
FLANGES ......................................................................................................................................................................................... 84
CLASS 125 ....................................................................................................................................................................... 85
CLASS 150 ....................................................................................................................................................................... 86
CLASS 300 ....................................................................................................................................................................... 88
Class 600 ....................................................................................................................................................................... 90
Class 900 ....................................................................................................................................................................... 92
Class 1500 .................................................................................................................................................................... 94
Class 2500 .................................................................................................................................................................... 96
REDUCING SLIP-ON AND THREADED FLANGES — ALL CLASSES ............................................................... 98
CALCULATED FLANGE WEIGHTS ............................................................................................................................. 99
FLANGE PACKAGING ................................................................................................................................................. 105
TECHNICAL DATA INDEX ......................................................................................................................................................... 106
RING TYPE JOINT FACING DIMENSIONS ............................................................................................................................ 148
WEL0333-10.081610
Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

nd!
eldbe
Worl d of W
t h e
l co m e to
p i o n eered
We e ed
e a r s , we'v nd design
0y sa f
o r over 6 echnique apable o steel
F t uely c n
nced arbo ts.
adva ent uniq he finest c e produc
m t g
equip cing only weld flan
u d ,
prod ttings an r p ledge el
fi so u
weld e ss, it i er only a ou
lev
bu s i n liv y
a fa mily ion, to de hat keeps
As ss tt
n d o ur mi d produc
a n
vice a r,
of ser satisfied. p a ce sette
f
100% r i n d ustry irection o
ou ed
o f b eing r from th tion.
u c
Proud l not deto er satisfa
i l m
we w ete custo
l
comp ratio
n
r p o
Co
e l d bend
W

weldbend... today!
• Weldbend is the industry leader with over

60 years of performance-proven reputation.
• Over 330,000 sq. ft. of manufacturing

and warehousing facilities on 36 acre site.
• A prime source producer of fittings • Trained personnel to guarantee prompt

and flanges from 1/2" through 60" sizes. processing of your orders from office to
the shipping dock.
• Using “Hi-Tech” research to guarantee
precision accuracy in machining • A total commitment to deliver on-spec,
and manufacturing. on-time… every time!

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com weldbend... today!
• From start to finish, Weldbend

strives to be "The Standard” to
which weld fittings and weld
flanges are manufactured, stored,
organized, and shipped. Weldbend
manufactures stock for large
inventories and prompt and
precise shipments.

plant tour
Pictures talk. Sounds from the scores of machines producing the highest quality weld fittings and weld
flanges fills the air. The smell of the freshly painted material, the constant movement of forklifts carrying
finished products, and each employee's dedication, can be clearly observed as you walk through our
dynamic facilities.
Moving into our extensive warehouse, weld fittings and weld flanges are carefully arranged from floor to
ceiling ready to be processed for immediate shipment to fill order requirements.
We’re proud to share our company with you!
8" – 10" – 12" Elbow Press

To our knowledge, this is the only fully-automatic elbow machine in the world that makes either 8", 10",
or 12" elbows. The blank is fed into the machine at one end and is automatically pushed to be heated to
forging temperature. It is then pushed over the mandrel and, when finished, it is automatically dropped
into a re-sizing die while still at forging temperature.
It is then automatically re-sized for perfect circularity. The re-sizing press opens automatically and
a mechanical hand takes the red-hot forging from the die.
This huge machine requires only one operator, with additional help from a cutoff machine operator
to load the blanks. This is a sight to behold!
14" – 24" Elbow Press

This state-of-the-art elbow press rises above the factory floor, and produces hot-formed large elbows with
unsurpassed precision. Joining with the 8" – 12" press, it allows Weldbend to produce a large range of exceptional
fittings to satisfy the most stringent requirements.

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com plant tour
• Examples of some of the high-quality

weld fittings and weld flanges
Weldbend produces on its state-of-
the-art equipment.

hot-formed elbows
• Made only from USA pipe, the

elbows hot-formed at Weldbend
are done to the highest quality
standards in Weldbend's unique
state-of-the-art processes.
10

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com cold tee press
• From seamless pipe to

finished seamless tees,
Weldbend produces our
cold-formed tees to the
highest specifications.
• As with the Weldbend elbows,
all seamless tees formed at
Weldbend are made with only
the highest quality USA pipe.
11

fitting finishing machines
• Weldbend's production facility produces

weld fittings to the highest standards possible.
• From cutting, beveling and other finishing

processes, Weldbend manufactures its
weld fittings in accordance to the
applicable standards.
12

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com fitting finishing machines
• After forming our

cold tees, Weldbend
subjects each tee
to stringent testing,
assuring the tees
which leave our facility
meet the quality-control standards
of the world's largest companies.
• Aside from the machine finishing of our

cold-formed tees after being heat treated,
Weldbend subjects each seamless tee
to magnetic particle testing in accordance
with the applicable standard (ASTM A-234),
ensuring each tee is of the highest
quality possible.
13

flange machining — Small and large flanges
• Each weld flange is machined and finished

to the exacting standards of ASME B16.5
or B16.47.
• Weldbend only uses steel from the finest

sources possible and is tested for
compliance with the appropriate standards.
14

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com warehousing
• Weldbend's “On-Hand” inventory policy

is designed with the distributor in mind.
Weldbend maintains a large inventory so you
receive your shipments in a timely manner.
• Look to us as the single reliable source
for precision-manufactured weld fittings and
weld flanges, from a 1/2" elbow to a 60" flange.
Be assured that it will be in stock, and it's
only minutes away from our shipping dock.
Weldbend stocks all materials in an organized
manner, ready to ship when needed.
15

packed in cartons
• Weldbend packages all

fittings possible 1/2" – 12"
and flanges 1/2" – 2 1/2"
in reinforced cardboard
cartons for ease of storage
and easy identification.
• Weldbend stores inventory in this

manner in order to maintain a
vast inventory for fast shipments.
16

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com our customers tell us...
”The Carton Way is the Better Way “
• Easier stacking • Factory-fresh condition

• Faster inventory counting at customer's job site
• Simplified inventory control • Helps control contractor's
• Less storage space in warehouse pilferage problem
• Weldbend Corporation pioneered the packing of carbon steel weld fittings in cartons, and we
still deliver products (in sizes up to 12") in strong corrugated cartons at no extra cost.
The Better Way Will Always Be The Weldbend Way!

17

quality assurance
ISO Certificates
• Weldbend is PED Compliant. Weldbend maintains a strict quality control system ensuring it
continually meets the most current ISO Certifications.
• For full size viewing, download from www.weldbend.com.
18

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com quality assurance
• Every product manufactured by

Weldbend must be burst tested
and certified before it goes into
production for the first time.
19

quality assurance
• Weldbend uses carefully

calibrated tools to continually
check the tolerance of all
manufactured products.
• All dimensions are

checked both by
the operator and
our quality control
department to ensure
the highest quality
finished goods.
• It is only after all these steps, that the Weldbend name

is applied to each of our weld fitting and weld flange
products. This signifies that the fitting or flange
manufactured in our plant, has passed our quality
control inspection, and is deemed ready for shipment.
20

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com the weldbend policy
THE WELDBEND POLICY
Weldbend fittings and flanges will meet all applicable

ASTM and ASME specifications.
If any Weldbend product fails to meet these ASTM

and ASME specifications, Weldbend, in strict accordance
with the terms of its warranty, will pay all freight
charges and will either replace the product or refund
the purchase price.
All Weldbend fittings and flanges are covered by a blanket

One Million Dollars ($1,000,000.00) Products Liability Policy
issued by a major United States insurance company.
Weldbend’s Terms and Conditions of Sales, including

complete warranty terms, are set forth on page 23
of this catalog. Additional copies of Weldbend’s Terms
and Conditions of Sales are available upon request.
Weldbend’s current Terms and Conditions of Sales are

available for download at www.weldbend.com.
21

ordering information
We make it easy for you to order or inquire, just give us your needs:
REQUIRED FITTING INFORMATION

When ordering or inquiring about Weldbend Fittings,
please specify the following information:
1. Quantity (Box quantities may apply)

2. Nominal Pipe Size
3. Pressure / Temperature Class
4. Type of Fitting
5. Piping Code Reference
6. Material
7. Box Quantities (See page 82)
REQUIRED FLANGE INFORMATION

When ordering or inquiring about Weldbend Flanges,
please specify the following information:
1. Quantity (Box and Bundle quantities may apply)

2. Nominal Pipe Size
3. Pressure / Temperature Class
4. Type of Flange
5. Piping Code Reference
6. Bore (When applicable)
7. Box and Bundle Quantities (See page 105)
SPECIAL MODIFICATIONS
If special modifications are required, the additional information must be supplied:
1. Matching Pipe Specifications

a) Outside Diameter
b) Wall Thickness
c) Minimum Yield Strength of Material
2. Bore of Flange (When applicable)
3. Facing Dimensions
4. Length Through the Hub
5. Flange Thickness
6. Diameter at the Base of Hub
7. Outside Diameter of Hub
8. Bolting Dimensions
9. Flange Gasket Material
22

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com terms and conditions
Weldbend Fittings and Flanges are products of Weldbend Corporation ("Weldbend"), Weldbend has the authority to make modifications or additions to this warranty in
TERMS AND CONDITIONS

a domestic manufacturer of welding fittings and welding flanges located at 6600 any respect except pursuant to a written agreement signed by a duly authorized
South Harlem Avenue, Argo, Illinois 60501-1930 U.S.A. officer of Weldbend.
All Weldbend Products are sold only upon the following Terms and Conditions. The 7. LIMITATION OF LIABILITY: UNDER NO CIRCUMSTANCES, WHETHER ALLEGED AS A
most current version of these Terms and Conditions may be found at Weldbend’s RESULT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE, STRICT LIABILITY
on-line catalogue: https://www.weldbend.com/catalog.pdf. OR ANY OTHER LEGAL THEORY, WILL WELDBEND BE RESPONSIBLE TO CUSTOMER,
OR TO ANY THIRD PARTY, FOR ANY SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL,
1. ACCEPTANCE: Once Weldbend accepts Customer's purchase order, the Terms and
INCIDENTAL OR OTHER DAMAGES OF ANY KIND, INCLUDING BUT NOT LIMITED TO
Conditions set forth herein shall constitute the entire agreement and understanding
LOST PROFITS, LOSS OF USE OF PROPERTY, OR DAMAGES FOR PERSONAL INJURY,
between Weldbend and Customer relating to the Weldbend products and merge all
AND NO CLAIMS FOR ANY SUCH DAMAGES SHALL BE BROUGHT BY THE CUSTOMER.
prior discussions, understandings, agreements and documents between them. Any
In no event shall Weldbend be liable to Customer for any amount in excess of the
variation to Weldbend's Terms and Conditions and any additional or different terms
purchase price of the product for which a claim is made. Customer shall not back
or conditions on any order form or other document submitted by Customer are
charge, counterclaim, or set-off its claims against payments due on its orders.
expressly rejected in their entirety unless and until expressly accepted in writing
by a duly authorized officer of Weldbend. 8. RETURN OF PRODUCTS AND/OR TERMINATION OF ORDERS: Customer shall not
return any products shipped by Weldbend without receiving the prior written
2. PRICE: All orders will be invoiced at Weldbend's current price schedule prevailing
permission and/or consent of Weldbend. If Customer seeks to cancel any part of
at the time of shipment and are subject to change without notice. C.O.D. charges
an order prior to shipment, such requests shall be made to Weldbend in writing at
may be added to the price of the products in Weldbend's sole discretion. All sales,
once. Except with respect to products which fail to conform to Customer's order or
use, excise and other applicable taxes shall be charged to Customer and remitted by
to Weldbend's limited warranty, all products returned shall be charged 25% of the
Customer to Weldbend.
value of the invoice and, in addition, freight charges for the return shipment (plus
3. SHIPMENTS: All materials will be delivered loaded onto the carrier Ex Works reimbursement to Weldbend of any freight charges incurred by Weldbend for the
Weldbend's plant. Once loaded, all risks of loss of materials will be assumed by original shipment to Customer). Any orders shipped by Weldbend and refused by
Customer. The shipper, method of shipment, and routing will be determined by Customer will be handled as a return products shipment. Any fitting or flange once
Weldbend, absent special agreement between Weldbend and Customer. All welded into a pipe line is not subject to return.
shipping and delivery dates are approximate. Weldbend shall not be responsible
9. SPECIAL-ORDER PRODUCTS. Any order for specially manufactured products that
for switching, spotting, handling, storage, demurrage, or any other transportation or
Weldbend does not ordinarily stock, including but not limited to barred tees, may not
related service, nor for any charges incurred therefor. Customer shall be responsible
be cancelled once accepted by Weldbend, and no such products may be returned.
for filing and pursuing claims with carriers for loss or damage in transit. Railroad and
Barred tees are manufactured in accordance with the process described at https://
other transportation permits as and when required shall be obtained by Customer.
www.weldbend.com/barredteeprocedure.pdf.
Weldbend reserves the right to deliver in more than one lot and to invoice each
lot separately. 10. PATENT AND OTHER RIGHTS: The sale of the products and the publication of
any information or technical data relating thereto do not imply freedom from
4. TERMS OF PAYMENT: Subject to the approval of Weldbend's credit department,
infringement of patent, copyright, registered design, or other industrial property
terms of payment will be net cash thirty (30) days from the date of invoice and will
rights in respect of any particular combination or application of the products. Nor
be payable in Chicago, Illinois. Shipments, deliveries, and performance of work
does the sale entail any license of Weldbend’s trademark or trade name.
shall at times be subject to the approval of Weldbend's credit department. Failure
to receive timely payment of invoices concerning work completed, and/or work 11. TERMINATION: If Customer defaults in payment of any sum due Weldbend or
in progress, shall be sufficient reason to withhold or delay subsequent shipments commits any breach of any of these Terms and Conditions or any other contract with
of materials, and/or performance of labor or to terminate all orders as set forth in Weldbend or if Customer's financial condition becomes unsatisfactory to Weldbend,
Section 10. If pursuant to this provision or to Section 10 herein Weldbend were to then Weldbend may, without prejudice to any other rights which may have accrued
defer any shipment or services or cancel in whole or in part any order, Customer shall or which may accrue to it, terminate all orders with that Customer by notice in writing
be liable for and reimburse Weldbend for all damage, including any and all direct or may defer shipment until the situation is remedied to Weldbend's satisfaction.
and consequential damage, incurred by Weldbend by reason of such deferment
12. MANUFACTURE AND AVAILABILITY OF PRODUCTS: Without prior notice, Weldbend
or cancellation. Unpaid invoices in excess of thirty (30) days shall be subject to an
reserves the right to change manufacturing methods and availability of products
interest charge at the rate of 1% per month from the date past due (but in no event
and reserves the right to sublet or contract work out to any company of its choice.
higher than the rate permitted by applicable law). In the event of Customer's default
Any products resulting from such sublet or contract work will be deemed Weldbend
of any of the terms of the contract, including but not limited to customer's failure
products and will be die-stamped with the trademarked Weldbend name and/or
to pay invoices timely, customer agrees to pay Weldbend all costs and expenses
Weldbend logo, and the sales of such products are subject to these Terms
incurred as a result thereof, including but not limited to reasonable attorneys' fees,
and Conditions.
court costs and all costs of collection.
13. ASSIGNMENT: Customer may not assign any right or duty arising under any order,
5. DELAYS: Weldbend shall be not responsible for any action or inaction of any
in whole or in part, without Weldbend's prior written consent.
carrier, including delays in delivery, nor, under any circumstances, shall Weldbend
be liable for any delay in performance, or non-performance, due to acts of God, war, 14. NO WAIVER OF RIGHTS; PARTIAL INVALIDITY: Any waiver by either party of any
riots, terrorism, civil disturbances, acts of civil or military authorities, governmental breach of a provision of these Terms and Conditions shall not be construed as a
regulation, court orders, fires, strikes or other labor disputes, shortages of labor, waiver of any other provision or of any continuing or succeeding breach of such
materials, fuel or energy, or unavailability of transportation, equipment failure, failure provision. If any provision of the Terms and Conditions shall be deemed invalid,
of supplier, carrier or subcontractor to deliver on time, or due to any other cause or illegal, or unenforceable in any respect, the legality and enforceability of all other
causes beyond the control of Weldbend. provisions of the Terms and Conditions shall not be in any way impaired or
affected thereby.
6. LIMITED, EXCLUSIVE WARRANTY: Weldbend warrants to its ORIGINAL CUSTOMER
ONLY, for a period of one year from the date of shipment, that all Weldbend 15. INDEMNITY: Customer shall indemnify and hold harmless Weldbend from any
fittings and flanges meet all applicable ASTM specifications and that Weldbend loss, cost, damage, or expense (including but not limited to attorney fees) arising from
is the unencumbered owner of all products shipped pursuant to these terms and any breach of these Terms and Conditions by Customer or from any other cause or
conditions. This warranty does not apply to products which have been damaged circumstance other than that covered by Weldbend’s limited, exclusive warranty.
during shipment or by abuse, misuse, misapplication, alteration or improper
16. COMPLIANCE WITH LAW: Customer is solely responsible for compliance with all
installation, maintenance or repair and is conditioned upon Customer (a) advising
applicable federal, state and local laws, ordinances, regulations, rules and standards
Weldbend in writing, within 10 days or receipt of products, of its belief that said
relating to the installation, maintenance, and use of the products purchased
products do not conform to ASTM specifications and (b) providing Weldbend
from Weldbend.
a reasonable time to inspect said products and investigate Customer's claim. If
Weldbend determines, in its sole opinion, that the products fail to conform to 17. LAW: The Terms and Conditions and any agreed amendment thereto shall be
ASTM specifications, it will, at its sole option, either refund all payments made by governed in all respects by the internal laws of the State of Illinois, without reference
customer with respect to such non-conforming products or, alternatively, replace to conflicts-of-laws rules. Any disputes shall be resolved in the state or federal courts
such non-conforming products and pay any additional shipping charges incurred located in Cook County, Illinois.
as a result thereof. Customer agrees to dispose of or return the non-conforming
18. NOTICES: Notices shall be deemed given if delivered by first-class, postage
products in accordance with instructions provided by Weldbend. THE FOREGOING
prepaid U.S. mail, or by courier service, to the address of the party as stated in the
SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE CUSTOMER AND THE EXCLUSIVE
order or these Terms and Conditions.
LIABILITY OF WELDBEND. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. NO Note: Weldbend’s catalog is for the exclusive use of the Jobber or Distributor of
WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE, Welding Fittings and Flanges. Weldbend Corporation restricts its sales to Jobbers
OR NON-INFRINGEMENT SHALL APPLY. No employee, agent or representative of and/or Distributors only.
Note: This catalog is for the exclusive use of the Jobber or Distributor of Welding Fittings and Flanges.
The Weldbend Corporation of Chicago restricts its sales to Jobbers and/or Distributors only. 23

24

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com FITtings
FITTINGS
1/2" through 60"
• Schedule Standard (STD)

• Schedule Extra-Strong (XS)
• Schedule 40
• Schedule 80
• Schedule 160
• Schedule Double Extra-Strong (XXS)
FITTINGS
All Products Backed by the Weldbend Warranty

25

90° Elbows
LONG RADIUS Outside Inside Wall Center Pipe Approx.
Pipe Diameter Diameter Thickness to End
SCHEDULE STD Size Schedule
Number
Weight in
Pounds
O.D. I.D. T C
1/2 0.84 0.622 0.109 1.50 40 0.16
3/4 1.05 0.824 0.113 1.50 40 0.17
1 1.32 1.049 0.133 1.50 40 0.40
1 1/4 1.66 1.380 0.140 1.88 40 0.55
1 1/2 1.90 1.610 0.145 2.25 40 0.80
2 2.38 2.067 0.154 3.00 40 1.60
2 1/2 2.88 2.469 0.203 3.75 40 3.20
3 3.50 3.068 0.216 4.50 40 4.80
3 1/2 4.00 3.548 0.226 5.25 40 6.60
4 4.50 4.026 0.237 6.00 40 8.90
5 5.56 5.047 0.258 7.50 40 15.10
6 6.62 6.065 0.280 9.00 40 24.00
8 8.62 7.981 0.322 12.00 40 47.80
10 10.75 10.020 0.365 15.00 40 83.40
12 12.75 12.000 0.375 18.00 * 123.00
FITTINGS
14 14.00 13.250 0.375 21.00 30 155.00

NOTES 16 16.00 15.250 0.375 24.00 30 206.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 18 18.00 17.250 0.375 27.00 * 262.00
2. All dimensions are in inches. 20 20.00 19.250 0.375 30.00 20 324.00
3. For bevel detail see page 107.
4. For dimensional tolerances see page 108.
24 24.00 23.250 0.375 36.00 20 466.00
5. For sizes larger than 48" please call. 30 30.00 29.250 0.375 45.00 * 720.00
6. All weights are in pounds and approximated 36 36.00 35.250 0.375 54.00 * 1039.00
or estimated.
* This size and thickness does not correspond
42 42.00 41.250 0.375 63.00 * 1420.00
to any pipe schedule number. 48 48.00 47.250 0.375 72.00 * 2000.00

SCHEDULE XS Size Schedule
Number
Weight in
Pounds
O.D. I.D. T C
1/2 0.84 0.546 0.147 1.50 80 0.26
3/4 1.05 0.742 0.154 1.50 80 0.29
1 1.32 0.957 0.179 1.50 80 0.48
1 1/4 1.66 1.278 0.191 1.88 80 0.79
1 1/2 1.90 1.500 0.200 2.25 80 1.20
2 2.38 1.939 0.218 3.00 80 2.10
2 1/2 2.88 2.323 0.276 3.75 80 3.80
3 3.50 2.900 0.300 4.50 80 6.30
3 1/2 4.00 3.364 0.318 5.25 80 8.60
4 4.50 3.826 0.337 6.00 80 12.50
5 5.56 4.813 0.375 7.50 80 21.20
6 6.62 5.761 0.432 9.00 80 34.40
8 8.62 7.625 0.500 12.00 80 71.30
10 10.75 9.750 0.500 15.00 60 111.00
12 12.75 11.750 0.500 18.00 * 158.00
14 14.00 13.000 0.500 21.00 * 201.00
NOTES 16 16.00 15.000 0.500 24.00 40 270.00
24 24.00 23.000 0.500 36.00 * 604.00
5. For sizes larger than 48" please call. 30 30.00 29.000 0.500 45.00 20 997.00
6. All weights are in pounds and approximated 36 36.00 35.000 0.500 54.00 20 1380.00
or estimated.
42 42.00 41.000 0.500 63.00 * 1880.00
26

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 90° Elbows
Outside Inside Wall Center Pipe Approx. LONG RADIUS

Size Schedule
Number
Weight in
Pounds
SCHEDULE 40
O.D. I.D. T C
1/2 0.84 0.622 0.109 1.50 40 0.16
3/4 1.05 0.824 0.113 1.50 40 0.17
1 1.32 1.054 0.133 1.50 40 0.40
1 1/4 1.66 1.380 0.140 1.88 40 0.55
1 1/2 1.90 1.610 0.145 2.25 40 0.80
2 2.38 2.072 0.154 3.00 40 1.60
2 1/2 2.88 2.474 0.203 3.75 40 3.20
3 3.50 3.068 0.216 4.50 40 4.80
3 1/2 4.00 3.548 0.226 5.25 40 6.60
4 4.50 4.026 0.237 6.00 40 8.90
5 5.56 5.044 0.258 7.50 40 15.10
6 6.62 6.060 0.280 9.00 40 24.00
8 8.62 7.976 0.322 12.00 40 47.80
10 10.75 10.020 0.365 15.00 40 83.40
12 12.75 11.938 0.406 18.00 40 123.00
FITTINGS
14 14.00 13.124 0.438 21.00 40 155.00
16 16.00 15.000 0.500 24.00 40 206.00 NOTES
18 18.00 16.876 0.562 27.00 40 262.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
20 20.00 18.812 0.594 30.00 40 324.00 2. All dimensions are in inches.
24 24.00 22.624 0.688 36.00 40 466.00 4. For dimensional tolerances see page 108.
5. For sizes larger than 24" please call.
6. All weights are in pounds and approximated
or estimated.

Size Schedule
Number
Weight in
Pounds
SCHEDULE 80
O.D. I.D. T C
1/2 0.84 0.546 0.147 1.50 80 0.26
3/4 1.05 0.742 0.154 1.50 80 0.29
1 1.32 0.962 0.179 1.50 80 0.48
1 1/4 1.66 1.278 0.191 1.88 80 0.79
1 1/2 1.90 1.500 0.200 2.25 80 1.20
2 2.38 1.944 0.218 3.00 80 2.10
2 1/2 2.88 2.328 0.276 3.75 80 3.80
3 3.50 2.900 0.300 4.50 80 6.30
3 1/2 4.00 3.364 0.318 5.25 80 8.60
4 4.50 3.826 0.337 6.00 80 12.50
5 5.56 4.810 0.375 7.50 80 21.20
6 6.62 5.756 0.432 9.00 80 34.40
8 8.62 7.620 0.500 12.00 80 71.30
10 10.75 9.562 0.594 15.00 80 111.00
12 12.75 11.374 0.688 18.00 80 158.00
14 14.00 12.500 0.750 21.00 80 201.00
16 16.00 14.312 0.844 24.00 80 270.00 NOTES
or estimated.
27

90° Elbows
SCHEDULE 160 Size Schedule
Number
Weight in
Pounds
O.D. I.D. T C
1/2 0.84 0.464 0.188 1.50 160 0.60
3/4 1.05 0.612 0.219 1.50 160 0.60
1 1.32 0.820 0.250 1.50 160 0.60
1 1/4 1.66 1.160 0.250 1.88 160 1.00
1 1/2 1.90 1.338 0.281 2.25 160 1.80
2 2.38 1.692 0.344 3.00 160 3.20
2 1/2 2.88 2.130 0.375 3.75 160 6.00
3 3.50 2.624 0.438 4.50 160 10.00
4 4.50 3.438 0.531 6.00 160 22.00
5 5.56 4.310 0.625 7.50 160 33.00
6 6.62 5.182 0.719 9.00 160 62.00
8 8.62 6.808 0.906 12.00 160 122.00
10 10.75 8.500 1.125 15.00 160 270.00
12 12.75 10.126 1.312 18.00 160 460.00
FITTINGS
14 14.00 11.188 1.406 21.00 160 563.00

16 16.00 12.812 1.594 24.00 160 825.00
NOTES 18 18.00 14.438 1.781 27.00 160 1240.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 20 20.00 16.062 1.969 30.00 160 1510.00
2. All dimensions are in inches.
24 24.00 19.312 2.344 36.00 160 1760.00
or estimated.

SCHEDULE XXS Size Schedule
Number
Weight in
Pounds
O.D. I.D. T C
1/2 0.84 0.252 0.294 1.50 * 0.30
3/4 1.05 0.434 0.308 1.50 * 0.30
1 1.32 0.604 0.358 1.50 * 0.80
1 1/4 1.66 0.896 0.382 1.88 * 1.40
1 1/2 1.90 1.100 0.400 2.25 * 2.00
2 2.38 1.508 0.436 3.00 * 3.90
2 1/2 2.88 1.776 0.552 3.75 * 6.80
3 3.50 2.300 0.600 4.50 * 11.30
4 4.50 3.152 0.674 6.00 * 23.00
5 5.56 4.060 0.750 7.50 * 38.00
6 6.62 4.892 0.864 9.00 * 69.00
8 8.62 6.870 0.875 12.00 * 120.00
10 10.75 8.750 1.000 15.00 140 232.00
12 12.75 10.750 1.000 18.00 120 315.00
NOTES
1. Conforms to ASME B16.9 & ASTM A234 WPB.
or estimated.
to any pipe schedule number.
28

TEL: 708/594-1700
FAX: 708/458-0106
Outside Inside Wall Center Pipe Approx. SHORT RADIUS

Size Schedule
Number
Weight in
Pounds
SCHEDULE STD
O.D. I.D. T C
1 1.32 1.049 0.133 1.00 40 0.30
1 1/4 1.66 1.380 0.140 1.25 40 0.40
1 1/2 1.90 1.610 0.145 1.50 40 0.50
2 2.38 2.067 0.154 2.00 40 1.00
2 1/2 2.88 2.469 0.203 2.50 40 2.00
3 3.50 3.068 0.216 3.00 40 3.00
3 1/2 4.00 3.548 0.226 3.50 40 4.30
4 4.50 4.026 0.237 4.00 40 6.10
5 5.56 5.047 0.258 5.00 40 9.70
6 6.62 6.065 0.280 6.00 40 16.70
8 8.62 7.981 0.322 8.00 40 32.40
10 10.75 10.020 0.365 10.00 40 56.30
12 12.75 12.000 0.375 12.00 * 79.40
14 14.00 13.250 0.375 14.00 30 104.00
16 16.00 15.250 0.375 16.00 30 129.00
FITTINGS
18 18.00 17.250 0.375 18.00 * 163.00
20 20.00 19.250 0.375 20.00 20 210.00 NOTES
❖ 30 30.00 29.250 0.375 30.00 * 470.00 2. All dimensions are in inches.
❖ 36 36.00 35.250 0.375 36.00 * 692.00 4. For dimensional tolerances see page 108.
❖ 42 42.00 41.250 0.375 42.00 * 967.00 5. For sizes larger than 48" please call.
❖ 48 48.00 47.250 0.375 48.00 * 1340.00 or estimated.
❖ In accordance with B16.9. Special Fittings
paragraph 4.4.2.

Size Schedule
Number
Weight in
Pounds
SCHEDULE XS
O.D. I.D. T C
1 1.32 0.962 0.179 1.00 80 0.30
1 1/4 1.66 1.278 0.191 1.25 80 0.60
1 1/2 1.90 1.500 0.200 1.50 80 0.80
2 2.38 1.939 0.218 2.00 80 1.50
2 1/2 2.88 2.323 0.276 2.50 80 2.60
3 3.50 2.900 0.300 3.00 80 3.80
3 1/2 4.00 3.364 0.318 3.50 80 5.40
4 4.50 3.826 0.337 4.00 80 7.60
5 5.56 4.813 0.375 5.00 80 13.80
6 6.62 5.761 0.432 6.00 80 22.80
8 8.62 7.625 0.500 8.00 80 47.30
10 10.75 9.750 0.500 10.00 60 71.00
12 12.75 11.750 0.500 12.00 * 104.00
14 14.00 13.000 0.500 14.00 * 137.00
16 16.00 15.000 0.500 16.00 40 171.00
18 18.00 17.000 0.500 18.00 * 214.00
20 20.00 19.000 0.500 20.00 30 277.00 NOTES
24 24.00 23.000 0.500 24.00 * 390.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
❖ 30 30.00 29.000 0.500 30.00 20 632.70 2. All dimensions are in inches.
❖ 36 36.00 35.000 0.500 36.00 20 913.00 4. For dimensional tolerances see page 108.
❖ 42 42.00 41.000 0.500 42.00 * 1300.00 5. For sizes larger than 48" please call.
❖ 48 48.00 47.000 0.500 48.00 * 1675.00 or estimated.
paragraph 4.4.2. 29

90° Elbows
SHORT RADIUS Outside Inside Wall Center Pipe Approx.
Number
Weight in
Pounds
O.D. I.D. T C
1 1.32 1.054 0.133 1.00 40 0.30
1 1/4 1.66 1.380 0.140 1.25 40 0.40
1 1/2 1.90 1.610 0.145 1.50 40 0.50
2 2.38 2.072 0.154 2.00 40 1.00
2 1/2 2.88 2.474 0.203 2.50 40 2.00
3 3.50 3.068 0.216 3.00 40 3.00
3 1/2 4.00 3.548 0.226 3.50 40 4.30
4 4.50 4.026 0.237 4.00 40 6.10
5 5.56 5.044 0.258 5.00 40 9.70
6 6.62 6.060 0.280 6.00 40 16.70
8 8.62 7.976 0.322 8.00 40 32.40
10 10.75 10.020 0.365 10.00 40 56.30
12 12.75 11.938 0.406 12.00 40 80.00
14 14.00 13.124 0.438 14.00 40 105.00
16 16.00 15.000 0.500 16.00 40 130.00
FITTINGS
18 18.00 16.876 0.562 18.00 40 165.00

NOTES 20 20.00 18.812 0.594 20.00 40 215.00
or estimated.
SHORT RADIUS Outside Inside Wall Center Pipe Approx.

Number
Weight in
Pounds
O.D. I.D. T C
1 1.32 0.962 0.179 1.00 80 0.30
1 1/4 1.66 1.278 0.191 1.25 80 0.60
1 1/2 1.90 1.500 0.200 1.50 80 0.80
2 2.38 1.944 0.218 2.00 80 1.50
2 1/2 2.88 2.328 0.276 2.50 80 2.60
3 3.50 2.900 0.300 3.00 80 3.80
3 1/2 4.00 3.364 0.318 3.50 80 5.40
4 4.50 3.826 0.337 4.00 80 7.60
5 5.56 4.810 0.375 5.00 80 13.80
6 6.62 5.756 0.432 6.00 80 22.80
8 8.62 7.620 0.500 8.00 80 47.30
10 10.75 9.562 0.594 10.00 80 75.00
12 12.75 11.374 0.688 12.00 80 105.00
14 14.00 12.500 0.750 14.00 80 140.00
16 16.00 14.312 0.844 16.00 80 175.00
18 18.00 16.124 0.938 18.00 80 215.00
NOTES 20 20.00 17.938 1.031 20.00 80 280.00
or estimated.
30

TEL: 708/594-1700
FAX: 708/458-0106

Size Schedule
Number
Weight in
Pounds
SCHEDULE 160
O.D. I.D. T C
1 1.32 0.820 0.250 1.00 160 0.50
1 1/4 1.66 1.160 0.250 1.25 160 0.90
1 1/2 1.90 1.338 0.281 1.50 160 1.50
2 2.38 1.692 0.344 2.00 160 2.90
2 1/2 2.88 2.130 0.375 2.50 160 5.50
3 3.50 2.624 0.438 3.00 160 9.80
4 4.50 3.438 0.531 4.00 160 20.00
5 5.56 4.310 0.625 5.00 160 30.00
6 6.62 5.182 0.719 6.00 160 60.00
8 8.62 6.808 0.906 8.00 160 125.00
10 10.75 8.500 1.125 10.00 160 258.00
12 12.75 10.126 1.312 12.00 160 455.00
14 14.00 11.188 1.406 14.00 160 550.00
16 16.00 12.812 1.594 16.00 160 800.00
18 18.00 14.438 1.781 18.00 160 1025.00
FITTINGS
20 20.00 16.062 1.969 20.00 160 1295.00
24 24.00 19.312 2.344 24.00 160 1450.00 NOTES
or estimated.

Size Schedule
Number
Weight in
Pounds
SCHEDULE XXS
O.D. I.D. T C
1 1.32 0.604 0.358 1.00 * 0.65
1 1/4 1.66 0.896 0.382 1.25 * 1.30
1 1/2 1.90 1.100 0.400 1.50 * 1.70
2 2.38 1.508 0.436 2.00 * 3.20
2 1/2 2.88 1.776 0.552 2.50 * 6.10
3 3.50 2.300 0.600 3.00 * 11.00
4 4.50 3.152 0.674 4.00 * 22.00
5 5.56 4.060 0.750 5.00 * 35.00
6 6.62 4.892 0.864 6.00 * 60.00
8 8.62 6.870 0.875 8.00 * 123.00
10 10.75 8.750 1.000 10.00 140 225.00
12 12.75 10.750 1.000 12.00 120 365.00
NOTES
or estimated.
31

90° reducing Elbows
SCHEDULE STD NOTES
For reference only 2. All dimensions are in inches.
or estimated.
Large Diameter Small Diameter

Center Pipe Approx.
Pipe Outside Inside Wall Outside Inside Wall to End Schedule Weight in
Size Diameter Diameter Thickness Diameter Diameter Thickness Number Pounds
O.D. I.D. T O.D. I.D. T C
2 x 1 1/2 2.38 2.072 0.154 1.90 1.610 0.145 3.00 40 1.40
2 x 1 1/4 2.38 2.072 0.154 1.66 1.380 0.140 3.00 40 1.30
2x1 2.38 2.072 0.154 1.32 1.054 0.133 3.00 40 1.20
FITTINGS
2 1/2 x 2 2.88 2.474 0.203 2.38 2.072 0.154 3.75 40 2.80

2 1/2 x 1 1/2 2.88 2.474 0.203 1.90 1.610 0.145 3.75 40 2.60
2 1/2 x 1 1/4 2.88 2.474 0.203 1.66 1.380 0.140 3.75 40 2.50
3 x 2 1/2 3.50 3.068 0.216 2.88 2.474 0.203 4.50 40 4.20
3x2 3.50 3.068 0.216 2.38 2.072 0.154 4.50 40 3.60
3 x 1 1/2 3.50 3.068 0.216 1.90 1.610 0.145 4.50 40 3.30
3 1/2 x 3 4.00 3.548 0.226 3.50 3.068 0.216 5.25 40 6.00
3 1/2 x 2 1/2 4.00 3.548 0.226 2.88 2.474 0.203 5.25 40 5.50
3 1/2 x 2 4.00 3.548 0.226 2.38 2.072 0.154 5.25 40 4.50
4 x 3 1/2 4.50 4.026 0.237 4.00 3.548 0.226 6.00 40 8.40
4x3 4.50 4.026 0.237 3.50 3.068 0.216 6.00 40 7.70
4 x 2 1/2 4.50 4.026 0.237 2.88 2.474 0.203 6.00 40 6.80
4x2 4.50 4.026 0.237 2.38 2.072 0.154 6.00 40 6.00
5x4 5.56 5.044 0.258 4.50 4.026 0.237 7.50 40 13.40
5 x 3 1/2 5.56 5.044 0.258 4.00 3.548 0.226 7.50 40 12.60
5x3 5.56 5.044 0.258 3.50 3.068 0.216 7.50 40 11.80
5 x 2 1/2 5.56 5.044 0.258 2.88 2.474 0.203 7.50 40 10.70
6x5 6.62 6.060 0.280 5.56 5.044 0.258 9.00 40 21.00
6x4 6.62 6.060 0.280 4.50 4.026 0.237 9.00 40 18.90
6 x 3 1/2 6.62 6.060 0.280 4.00 3.548 0.226 9.00 40 17.80
6x3 6.62 6.060 0.280 3.50 3.068 0.216 9.00 40 16.80
8x6 8.62 7.976 0.322 6.62 6.060 0.280 12.00 40 39.70
8x5 8.62 7.976 0.322 5.56 5.044 0.258 12.00 40 36.20
8x4 8.62 7.976 0.322 4.50 4.026 0.237 12.00 40 33.10
10 x 8 10.75 10.020 0.365 8.62 7.976 0.322 15.00 40 73.00
10 x 6 10.75 10.020 0.365 6.62 6.060 0.280 15.00 40 63.20
10 x 5 10.75 10.020 0.365 5.56 5.044 0.258 15.00 40 58.50
12 x 10 12.75 12.000 0.375 10.75 10.020 0.365 18.00 * 113.00
12 x 8 12.75 12.000 0.375 8.62 7.976 0.322 18.00 * 98.40
12 x 6 12.75 12.000 0.375 6.62 6.060 0.280 18.00 * 86.50
32

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 90° reducing Elbows
NOTES SCHEDULE XS
2. All dimensions are in inches. For reference only
4. For dimensional tolerances see page 108 .
or estimated.

Center Pipe Approx.
2 x 1 1/2 2.38 1.944 0.218 1.90 1.500 0.200 3.00 80 1.90
2 x 1 1/4 2.38 1.944 0.218 1.66 1.278 0.191 3.00 80 1.80
2x1 2.38 1.944 0.218 1.32 0.962 0.179 3.00 80 1.70
2 1/2 x 2 2.88 2.328 0.276 2.38 1.944 0.218 3.75 80 3.40
FITTINGS
2 1/2 x 1 1/2 2.88 2.328 0.276 1.90 1.500 0.200 3.75 80 3.00
2 1/2 x 1 1/4 2.88 2.328 0.276 1.66 1.278 0.191 3.75 80 2.90
3 x 2 1/2 3.50 2.900 0.300 2.88 2.328 0.276 4.50 80 5.70
3x2 3.50 2.900 0.300 2.38 1.944 0.218 4.50 80 4.90
3 x 1 1/2 3.50 2.900 0.300 1.90 1.500 0.200 4.50 80 4.50
3 1/2 x 3 4.00 3.364 0.318 3.50 2.900 0.300 5.25 80 8.20
3 1/2 x 2 1/2 4.00 3.364 0.318 2.88 2.328 0.276 5.25 80 7.30
3 1/2 x 2 4.00 3.364 0.318 2.38 1.944 0.218 5.25 80 6.40
4 x 3 1/2 4.50 3.826 0.337 4.00 3.364 0.318 6.00 80 11.40
4x3 4.50 3.826 0.337 3.50 2.900 0.300 6.00 80 10.50
4 x 2 1/2 4.50 3.826 0.337 2.88 2.328 0.276 6.00 80 9.40
4x2 4.50 3.826 0.337 2.38 1.944 0.218 6.00 80 8.40
5x4 5.56 4.810 0.375 4.50 3.826 0.337 7.50 80 18.80
5 x 3 1/2 5.56 4.810 0.375 4.00 3.364 0.318 7.50 80 17.40
5x3 5.56 4.810 0.375 3.50 2.900 0.300 7.50 80 16.50
5 x 2 1/2 5.56 4.810 0.375 2.88 2.328 0.276 7.50 80 15.10
6x5 6.62 5.756 0.432 5.56 4.810 0.375 9.00 80 31.40
6x4 6.62 5.756 0.432 4.50 3.826 0.337 9.00 80 27.90
6 x 3 1/2 6.62 5.756 0.432 4.00 3.364 0.318 9.00 80 26.30
6x3 6.62 5.756 0.432 3.50 2.900 0.300 9.00 80 24.90
8x6 8.62 7.620 0.500 6.62 5.756 0.432 12.00 80 60.80
8x5 8.62 7.620 0.500 5.56 4.810 0.375 12.00 80 54.30
8x4 8.62 7.620 0.500 4.50 3.826 0.337 12.00 80 49.50
10 x 8 10.75 9.750 0.500 8.62 7.620 0.500 15.00 * 102.00
10 x 6 10.75 9.750 0.500 6.62 5.756 0.432 15.00 * 86.50
10 x 5 10.75 9.750 0.500 5.56 4.810 0.375 15.00 * 78.50
12 x 10 12.75 11.750 0.500 10.75 9.750 0.500 18.00 * 148.00
12 x 8 12.75 11.750 0.500 8.62 7.620 0.500 18.00 * 132.00
12 x 6 12.75 11.750 0.500 6.62 5.756 0.432 18.00 * 114.00
33

90° reducing Elbows
SCHEDULE 40 NOTES
For reference only 2. All dimensions are in inches.
or estimated.

Center Pipe Approx.
2 x 1 1/2 2.38 2.072 0.154 1.90 1.610 0.145 3.00 40 1.40
2 x 1 1/4 2.38 2.072 0.154 1.66 1.380 0.140 3.00 40 1.30
2x1 2.38 2.072 0.154 1.32 1.054 0.133 3.00 40 1.20
FITTINGS
2 1/2 x 2 2.88 2.474 0.203 2.38 2.072 0.154 3.75 40 2.80

2 1/2 x 1 1/2 2.88 2.474 0.203 1.90 1.610 0.145 3.75 40 2.60
2 1/2 x 1 1/4 2.88 2.474 0.203 1.66 1.380 0.140 3.75 40 2.50
3 x 2 1/2 3.50 3.068 0.216 2.88 2.474 0.203 4.50 40 4.20
3x2 3.50 3.068 0.216 2.38 2.072 0.154 4.50 40 3.60
3 x 1 1/2 3.50 3.068 0.216 1.90 1.610 0.145 4.50 40 3.30
3 1/2 x 3 4.00 3.548 0.226 3.50 3.068 0.216 5.25 40 6.00
3 1/2 x 2 1/2 4.00 3.548 0.226 2.88 2.474 0.203 5.25 40 5.50
3 1/2 x 2 4.00 3.548 0.226 2.38 2.072 0.154 5.25 40 4.50
4 x 3 1/2 4.50 4.026 0.237 4.00 3.548 0.226 6.00 40 8.40
4x3 4.50 4.026 0.237 3.50 3.068 0.216 6.00 40 7.70
4 x 2 1/2 4.50 4.026 0.237 2.88 2.474 0.203 6.00 40 6.80
4x2 4.50 4.026 0.237 2.38 2.072 0.154 6.00 40 6.00
5x4 5.56 5.044 0.258 4.50 4.026 0.237 7.50 40 13.40
5 x 3 1/2 5.56 5.044 0.258 4.00 3.548 0.226 7.50 40 12.60
5x3 5.56 5.044 0.258 3.50 3.068 0.216 7.50 40 11.80
5 x 2 1/2 5.56 5.044 0.258 2.88 2.474 0.203 7.50 40 10.70
6x5 6.62 6.060 0.280 5.56 5.044 0.258 9.00 40 21.00
6x4 6.62 6.060 0.280 4.50 4.026 0.237 9.00 40 18.90
6 x 3 1/2 6.62 6.060 0.280 4.00 3.548 0.226 9.00 40 17.80
6x3 6.62 6.060 0.280 3.50 3.068 0.216 9.00 40 16.80
8x6 8.62 7.976 0.322 6.62 6.060 0.280 12.00 40 39.70
8x5 8.62 7.976 0.322 5.56 5.044 0.258 12.00 40 36.20
8x4 8.62 7.976 0.322 4.50 4.026 0.237 12.00 40 33.10
10 x 8 10.75 10.020 0.365 8.62 7.976 0.322 15.00 40 73.00
10 x 6 10.75 10.020 0.365 6.62 6.060 0.280 15.00 40 63.20
10 x 5 10.75 10.020 0.365 5.56 5.044 0.258 15.00 40 58.50
12 x 10 12.75 11.938 0.406 10.75 10.020 0.365 18.00 40 115.00
12 x 8 12.75 11.938 0.406 8.62 7.976 0.322 18.00 40 100.00
12 x 6 12.75 11.938 0.406 6.62 6.060 0.280 18.00 40 90.00
34

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 90° reducing Elbows
NOTES SCHEDULE 80
2. All dimensions are in inches. For reference only
or estimated.

Center Pipe Approx.
2 x 1 1/2 2.38 1.944 0.218 1.90 1.500 0.200 3.00 80 1.90
2 x 1 1/4 2.38 1.944 0.218 1.66 1.278 0.191 3.00 80 1.80
2x1 2.38 1.944 0.218 1.32 0.962 0.179 3.00 80 1.70
2 1/2 x 2 2.88 2.328 0.276 2.38 1.944 0.218 3.75 80 3.40
FITTINGS
2 1/2 x 1 1/2 2.88 2.328 0.276 1.90 1.500 0.200 3.75 80 3.00
2 1/2 x 1 1/4 2.88 2.328 0.276 1.66 1.278 0.191 3.75 80 2.90
3 x 2 1/2 3.50 2.900 0.300 2.88 2.328 0.276 4.50 80 5.70
3x2 3.50 2.900 0.300 2.38 1.944 0.218 4.50 80 4.90
3 x 1 1/2 3.50 2.900 0.300 1.90 1.500 0.200 4.50 80 4.50
3 1/2 x 3 4.00 3.364 0.318 3.50 2.900 0.300 5.25 80 8.20
3 1/2 x 2 1/2 4.00 3.364 0.318 2.88 2.328 0.276 5.25 80 7.30
3 1/2 x 2 4.00 3.364 0.318 2.38 1.944 0.218 5.25 80 6.40
4 x 3 1/2 4.50 3.826 0.337 4.00 3.364 0.318 6.00 80 11.40
4x3 4.50 3.826 0.337 3.50 2.900 0.300 6.00 80 10.50
4 x 2 1/2 4.50 3.826 0.337 2.88 2.328 0.276 6.00 80 9.40
4x2 4.50 3.826 0.337 2.38 1.944 0.218 6.00 80 8.40
5x4 5.56 4.810 0.375 4.50 3.826 0.337 7.50 80 18.80
5 x 3 1/2 5.56 4.810 0.375 4.00 3.364 0.318 7.50 80 17.40
5x3 5.56 4.810 0.375 3.50 2.900 0.300 7.50 80 16.50
5 x 2 1/2 5.56 4.810 0.375 2.88 2.328 0.276 7.50 80 15.10
6x5 6.62 5.756 0.432 5.56 4.810 0.375 9.00 80 31.40
6x4 6.62 5.756 0.432 4.50 3.826 0.337 9.00 80 27.90
6 x 3 1/2 6.62 5.756 0.432 4.00 3.364 0.318 9.00 80 26.30
6x3 6.62 5.756 0.432 3.50 2.900 0.300 9.00 80 24.90
8x6 8.62 7.620 0.500 6.62 5.756 0.432 12.00 80 60.80
8x5 8.62 7.620 0.500 5.56 4.810 0.375 12.00 80 54.30
8x4 8.62 7.620 0.500 4.50 3.826 0.337 12.00 80 49.50
10 x 8 10.75 9.562 0.594 8.62 7.620 0.500 15.00 80 105.00
10 x 6 10.75 9.562 0.594 6.62 5.756 0.432 15.00 80 90.00
10 x 5 10.75 9.562 0.594 5.56 4.810 0.375 15.00 80 80.00
12 x 10 12.75 11.374 0.688 10.75 9.562 0.594 18.00 80 155.00
12 x 8 12.75 11.374 0.688 8.62 7.620 0.500 18.00 80 135.00
12 x 6 12.75 11.374 0.688 6.62 5.756 0.432 18.00 80 120.00
35

90° Elbows
3R Outside Inside Wall Center Pipe Approx.
Number
Weight in
Pounds
O.D. I.D. T C
3/4 1.05 0.824 0.113 2.25 40 0.30
1 1.32 1.054 0.133 3.00 40 0.80
1 1/4 1.66 1.380 0.140 3.75 40 1.10
1 1/2 1.90 1.610 0.145 4.50 40 1.60
2 2.38 2.072 0.154 6.00 40 3.20
2 1/2 2.88 2.474 0.203 7.50 40 6.40
3 3.50 3.068 0.216 9.00 40 9.60
3 1/2 4.00 3.548 0.226 10.50 40 15.00
4 4.50 4.026 0.237 12.00 40 17.80
5 5.56 5.044 0.258 15.00 40 30.00
6 6.62 6.060 0.280 18.00 40 48.00
8 8.62 7.976 0.322 24.00 40 95.00
10 10.75 10.020 0.365 30.00 40 167.00
12 12.75 12.000 0.375 36.00 * 250.00
14 14.00 13.250 0.375 42.00 30 310.00
FITTINGS
16 16.00 15.250 0.375 48.00 30 415.00

NOTES 18 18.00 17.250 0.375 54.00 * 530.00
or estimated.

Number
Weight in
Pounds
O.D. I.D. T C
3/4 1.05 0.742 0.154 2.25 80 0.30
1 1.32 0.962 0.179 3.00 80 1.58
1 1/4 1.66 1.278 0.191 3.75 80 2.40
1 1/2 1.90 1.500 0.200 4.50 80 4.20
2 2.38 1.944 0.218 6.00 80 7.60
2 1/2 2.88 2.328 0.276 7.50 80 12.60
3 3.50 2.900 0.300 9.00 80 17.20
3 1/2 4.00 3.364 0.318 10.50 80 22.00
4 4.50 3.826 0.337 12.00 80 25.00
5 5.56 4.810 0.375 15.00 80 45.00
6 6.62 5.756 0.432 18.00 80 70.00
8 8.62 7.620 0.500 24.00 80 145.00
10 10.75 9.750 0.500 30.00 60 225.00
12 12.75 11.750 0.500 36.00 * 320.00
14 14.00 13.000 0.500 42.00 * 405.00
16 16.00 15.000 0.500 48.00 40 540.00
NOTES 18 18.00 17.000 0.500 54.00 * 700.00
2. All dimensions are in inches. 24 24.00 23.000 0.500 72.00 * 1210.00
or estimated.
36

TEL: 708/594-1700
FAX: 708/458-0106
Outside Inside Wall Center Pipe Approx. 3R

Size Schedule
Number
Weight in
Pounds
SCHEDULE 40
O.D. I.D. T C
3/4 1.05 0.824 0.113 2.25 40 0.30
1 1.32 1.054 0.133 3.00 40 0.80
1 1/4 1.66 1.380 0.140 3.75 40 1.10
1 1/2 1.90 1.610 0.145 4.50 40 1.60
2 2.38 2.072 0.154 6.00 40 3.20
2 1/2 2.88 2.474 0.203 7.50 40 6.40
3 3.50 3.068 0.216 9.00 40 9.60
3 1/2 4.00 3.548 0.226 10.50 40 15.00
4 4.50 4.026 0.237 12.00 40 17.80
5 5.56 5.044 0.258 15.00 40 30.00
6 6.62 6.060 0.280 18.00 40 48.00
8 8.62 7.976 0.322 24.00 40 95.00
10 10.75 10.020 0.365 30.00 40 167.00
12 12.75 11.938 0.406 36.00 40 205.00
14 14.00 13.124 0.438 42.00 40 305.00
FITTINGS
16 16.00 15.000 0.500 48.00 40 540.00
18 18.00 16.876 0.562 54.00 40 740.00 NOTES
or estimated.

Size Schedule
Number
Weight in
Pounds
SCHEDULE 80
O.D. I.D. T C
3/4 1.05 0.742 0.154 2.25 80 0.30
1 1.32 0.962 0.179 3.00 80 1.58
1 1/4 1.66 1.278 0.191 3.75 80 2.40
1 1/2 1.90 1.500 0.200 4.50 80 4.20
2 2.38 1.944 0.218 6.00 80 7.60
2 1/2 2.88 2.328 0.276 7.50 80 12.60
3 3.50 2.900 0.300 9.00 80 17.20
3 1/2 4.00 3.364 0.318 10.50 80 22.00
4 4.50 3.826 0.337 12.00 80 25.00
5 5.56 4.810 0.375 15.00 80 45.00
6 6.62 5.756 0.432 18.00 80 70.00
8 8.62 7.620 0.500 24.00 80 145.00
10 10.75 9.562 0.594 30.00 80 200.00
12 12.75 11.374 0.688 36.00 80 320.00
14 14.00 12.500 0.750 42.00 80 600.00
16 16.00 14.312 0.844 48.00 80 810.00
18 18.00 16.124 0.938 54.00 80 1020.00 NOTES
or estimated.
37

45° Elbows
Number
Weight in
Pounds
O.D. I.D. T A
1/2 0.84 0.622 0.109 0.62 40 0.09
3/4 1.05 0.824 0.113 0.75 40 0.10
1 1.32 1.049 0.133 0.88 40 0.22
1 1/4 1.66 1.380 0.140 1.00 40 0.33
1 1/2 1.90 1.610 0.145 1.12 40 0.43
2 2.38 2.067 0.154 1.38 40 0.85
2 1/2 2.88 2.469 0.203 1.75 40 1.70
3 3.50 3.068 0.216 2.00 40 2.50
3 1/2 4.00 3.548 0.226 2.25 40 3.40
4 4.50 4.026 0.237 2.50 40 4.50
5 5.56 5.047 0.258 3.12 40 7.50
6 6.62 6.065 0.280 3.75 40 11.70
8 8.62 7.981 0.322 5.00 40 23.30
10 10.75 10.020 0.365 6.25 40 40.90
12 12.75 12.000 0.375 7.50 * 61.40
FITTINGS
14 14.00 13.250 0.375 8.75 30 78.10

NOTES 16 16.00 15.250 0.375 10.00 30 101.00
24 24.00 23.250 0.375 15.00 20 231.00
5. For sizes larger than 48" please call. 30 30.00 29.250 0.375 18.50 * 358.00
or estimated.
42 42.00 41.250 0.375 26.00 * 707.00

Number
Weight in
Pounds
O.D. I.D. T A
1/2 0.84 0.546 0.147 0.62 80 0.15
3/4 1.05 0.742 0.154 0.75 80 0.16
1 1.32 0.957 0.179 0.88 80 0.28
1 1/4 1.66 1.278 0.191 1.00 80 0.45
1 1/2 1.90 1.500 0.200 1.12 80 0.61
2 2.38 1.939 0.218 1.38 80 1.20
2 1/2 2.88 2.323 0.276 1.75 80 2.00
3 3.50 2.900 0.300 2.00 80 3.30
3 1/2 4.00 3.364 0.318 2.25 80 4.50
4 4.50 3.826 0.337 2.50 80 6.20
5 5.56 4.813 0.375 3.12 80 10.50
6 6.62 5.761 0.432 3.75 80 17.00
8 8.62 7.625 0.500 5.00 80 34.30
10 10.75 9.750 0.500 6.25 60 53.50
12 12.75 11.750 0.500 7.50 * 77.60
14 14.00 13.000 0.500 8.75 * 100.00
NOTES 16 16.00 15.000 0.500 10.00 40 134.00
24 24.00 23.000 0.500 15.00 * 302.00
5. For sizes larger than 48" please call. 30 30.00 29.000 0.500 18.50 20 475.10
6. All weights are in pounds and approximated 36 36.00 35.000 0.500 22.25 20 686.10
or estimated.
42 42.00 41.000 0.500 26.00 * 936.10
38

TEL: 708/594-1700
FAX: 708/458-0106

Size Schedule
Number
Weight in
Pounds
SCHEDULE 40
O.D. I.D. T A
1/2 0.84 0.622 0.109 0.62 40 0.09
3/4 1.05 0.824 0.113 0.75 40 0.10
1 1.32 1.054 0.133 0.88 40 0.22
1 1/4 1.66 1.380 0.140 1.00 40 0.33
1 1/2 1.90 1.610 0.145 1.12 40 0.43
2 2.38 2.072 0.154 1.38 40 0.85
2 1/2 2.88 2.474 0.203 1.75 40 1.70
3 3.50 3.068 0.216 2.00 40 2.50
3 1/2 4.00 3.548 0.226 2.25 40 3.40
4 4.50 4.026 0.237 2.50 40 4.50
5 5.56 5.044 0.258 3.12 40 7.50
6 6.62 6.060 0.280 3.75 40 11.70
8 8.62 7.976 0.322 5.00 40 23.30
10 10.75 10.020 0.365 6.25 40 40.90
12 12.75 11.938 0.406 7.50 40 65.00
FITTINGS
14 14.00 13.124 0.438 8.75 40 80.00
16 16.00 15.000 0.500 10.00 40 105.00 NOTES
or estimated.

Size Schedule
Number
Weight in
Pounds
SCHEDULE 80
O.D. I.D. T A
1/2 0.84 0.546 0.147 0.62 80 0.15
3/4 1.05 0.742 0.154 0.75 80 0.16
1 1.32 0.962 0.179 0.88 80 0.28
1 1/4 1.66 1.278 0.191 1.00 80 0.45
1 1/2 1.90 1.500 0.200 1.12 80 0.61
2 2.38 1.944 0.218 1.38 80 1.20
2 1/2 2.88 2.328 0.276 1.75 80 2.00
3 3.50 2.900 0.300 2.00 80 3.30
3 1/2 4.00 3.364 0.318 2.25 80 4.50
4 4.50 3.826 0.337 2.50 80 6.20
5 5.56 4.810 0.375 3.12 80 10.50
6 6.62 5.756 0.432 3.75 80 17.00
8 8.62 7.620 0.500 5.00 80 34.30
10 10.75 9.562 0.594 6.25 80 55.00
12 12.75 11.374 0.688 7.50 80 80.00
14 14.00 12.500 0.750 8.75 80 100.00
16 16.00 14.312 0.844 10.00 80 135.00 NOTES
or estimated.
39

45° Elbows
Number
Weight in
Pounds
O.D. I.D. T A
1/2 0.84 0.464 0.188 0.62 160 1.80
3/4 1.05 0.612 0.219 0.75 160 2.00
1 1.32 0.820 0.250 0.88 160 3.00
1 1/4 1.66 1.160 0.250 1.00 160 3.50
1 1/2 1.90 1.338 0.281 1.12 160 3.70
2 2.38 1.692 0.344 1.38 160 5.00
2 1/2 2.88 2.130 0.375 1.75 160 3.70
3 3.50 2.624 0.438 2.00 160 5.60
4 4.50 3.438 0.531 2.50 160 5.60
5 5.56 4.310 0.625 3.12 160 15.00
6 6.62 5.182 0.719 3.75 160 28.00
8 8.62 6.808 0.906 5.00 160 48.00
10 10.75 8.500 1.125 6.25 160 72.00
12 12.75 10.126 1.312 7.50 160 98.00
FITTINGS
14 14.00 11.188 1.406 8.75 160 130.00

16 16.00 12.812 1.594 10.00 160 180.00
NOTES 18 18.00 14.438 1.781 11.25 160 260.00
24 24.00 19.312 2.344 15.00 160 560.00
or estimated.

Number
Weight in
Pounds
O.D. I.D. T A
1/2 0.84 0.252 0.294 0.62 * 1.80
3/4 1.05 0.434 0.308 0.75 * 2.00
1 1.32 0.604 0.358 0.88 * 3.00
1 1/4 1.66 0.896 0.382 1.00 * 3.50
1 1/2 1.90 1.100 0.400 1.12 * 3.70
2 2.38 1.508 0.436 1.38 * 5.00
2 1/2 2.88 1.776 0.552 1.75 * 3.70
3 3.50 2.300 0.600 2.00 * 6.00
4 4.50 3.152 0.674 2.50 * 10.40
5 5.56 4.060 0.750 3.12 * 19.20
6 6.62 4.892 0.864 3.75 * 30.00
8 8.62 6.870 0.875 5.00 * 50.00
10 10.75 8.750 1.000 6.25 140 75.00
12 12.75 10.750 1.000 7.50 120 95.00
NOTES
or estimated.
40

TEL: 708/594-1700
FAX: 708/458-0106

Size Schedule
Number
Weight in
Pounds
SCHEDULE STD
O.D. I.D. T A
3/4 1.05 0.824 0.113 0.94 40 0.50
1 1.32 1.054 0.133 1.25 40 0.70
1 1/4 1.66 1.380 0.140 1.56 40 1.00
1 1/2 1.90 1.610 0.145 1.88 40 1.30
2 2.38 2.072 0.154 2.50 40 1.50
2 1/2 2.88 2.474 0.203 3.12 40 1.75
3 3.50 3.068 0.216 3.75 40 3.00
3 1/2 4.00 3.548 0.226 4.38 40 5.00
4 4.50 4.026 0.237 5.00 40 9.00
5 5.56 5.044 0.258 6.19 40 16.00
6 6.62 6.060 0.280 7.44 40 22.50
8 8.62 7.976 0.322 9.94 40 45.00
10 10.75 10.020 0.365 12.44 40 80.00
12 12.75 12.000 0.375 14.88 * 120.00
14 14.00 13.250 0.375 17.38 30 150.00
FITTINGS
16 16.00 15.250 0.375 19.88 30 193.00
18 18.00 17.250 0.375 22.38 * 248.00 NOTES
or estimated.

Size Schedule
Number
Weight in
Pounds
SCHEDULE XS
O.D. I.D. T A
3/4 1.05 0.742 0.154 0.94 80 0.16
1 1.32 0.962 0.179 1.25 80 0.28
1 1/4 1.66 1.278 0.191 1.56 80 0.45
1 1/2 1.90 1.500 0.200 1.88 80 0.61
2 2.38 1.944 0.218 2.50 80 1.20
2 1/2 2.88 2.328 0.276 3.12 80 2.00
3 3.50 2.900 0.300 3.75 80 3.30
3 1/2 4.00 3.364 0.318 4.38 80 4.50
4 4.50 3.826 0.337 5.00 80 6.20
5 5.56 4.810 0.375 6.19 80 10.50
6 6.62 5.756 0.432 7.44 80 17.00
8 8.62 7.620 0.500 9.94 80 34.30
10 10.75 9.750 0.500 12.44 60 53.50
12 12.75 11.750 0.500 14.88 * 77.60
14 14.00 13.000 0.500 17.38 * 100.00
16 16.00 15.000 0.500 19.88 40 134.00
18 18.00 17.000 0.500 22.38 * 170.00 NOTES
24 24.00 23.000 0.500 29.81 * 302.00 2. All dimensions are in inches.
or estimated.
41

45° Elbows
Number
Weight in
Pounds
O.D. I.D. T A
3/4 1.05 0.824 0.113 0.94 40 0.50
1 1.32 1.054 0.133 1.25 40 0.70
1 1/4 1.66 1.380 0.140 1.56 40 1.00
1 1/2 1.90 1.610 0.145 1.88 40 1.30
2 2.38 2.072 0.154 2.50 40 1.50
2 1/2 2.88 2.474 0.203 3.12 40 1.75
3 3.50 3.068 0.216 3.75 40 3.00
3 1/2 4.00 3.548 0.226 4.38 40 5.00
4 4.50 4.026 0.237 5.00 40 9.00
5 5.56 5.044 0.258 6.19 40 16.00
6 6.62 6.060 0.280 7.44 40 22.50
8 8.62 7.976 0.322 9.94 40 45.00
10 10.75 10.020 0.365 12.44 40 80.00
12 12.75 11.938 0.406 14.88 40 160.00
14 14.00 13.124 0.438 17.38 40 270.00
FITTINGS
16 16.00 15.000 0.500 19.88 40 360.00

NOTES 18 18.00 16.876 0.562 22.38 40 490.00
or estimated.

Number
Weight in
Pounds
O.D. I.D. T A
3/4 1.05 0.742 0.154 0.94 80 0.16
1 1.32 0.962 0.179 1.25 80 0.28
1 1/4 1.66 1.278 0.191 1.56 80 0.45
1 1/2 1.90 1.500 0.200 1.88 80 0.61
2 2.38 1.944 0.218 2.50 80 1.20
2 1/2 2.88 2.328 0.276 3.12 80 2.00
3 3.50 2.900 0.300 3.75 80 3.30
3 1/2 4.00 3.364 0.318 4.38 80 4.50
4 4.50 3.826 0.337 5.00 80 6.20
5 5.56 4.810 0.375 6.19 80 10.50
6 6.62 5.756 0.432 7.44 80 17.00
8 8.62 7.620 0.500 9.94 80 34.30
10 10.75 9.562 0.594 12.44 80 150.00
12 12.75 11.374 0.688 14.88 80 200.00
14 14.00 12.500 0.750 17.38 80 337.50
16 16.00 14.312 0.844 19.88 80 450.00
NOTES 18 18.00 16.124 0.938 22.38 80 612.50
or estimated.
42

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 180° Return bends
Outside Inside Wall Center Back Pipe Approx.

LONG RADIUS
Pipe Diameter Diameter Thickness to Center to Face
Size Schedule
Number
Weight in
Pounds
SCHEDULE STD
O.D. I.D. T V W
1/2 0.84 0.622 0.109 3.00 1.88 40 0.32
3/4 1.05 0.824 0.113 3.00 2.00 40 0.34
1 1.32 1.049 0.133 3.00 2.19 40 0.74
1 1/4 1.66 1.380 0.140 3.75 2.75 40 1.10
1 1/2 1.90 1.610 0.145 4.50 3.25 40 1.60
2 2.38 2.067 0.154 6.00 4.19 40 3.20
2 1/2 2.88 2.469 0.203 7.50 5.19 40 6.10
3 3.50 3.068 0.216 9.00 6.25 40 9.40
3 1/2 4.00 3.548 0.226 10.50 7.25 40 12.80
4 4.50 4.026 0.237 12.00 8.25 40 17.50
5 5.56 5.047 0.258 15.00 10.31 40 29.30
6 6.62 6.065 0.280 18.00 12.31 40 47.00
8 8.62 7.981 0.322 24.00 16.31 40 87.00
10 10.75 10.020 0.365 30.00 20.38 40 164.00
12 12.75 12.000 0.375 36.00 24.38 * 237.00
FITTINGS
14 14.00 13.250 0.375 42.00 28.00 30 311.00
16 16.00 15.250 0.375 48.00 32.00 30 408.00 NOTES
18 18.00 17.250 0.375 54.00 36.00 * 514.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
20 20.00 19.250 0.375 60.00 40.00 20 636.00 2. All dimensions are in inches.
24 24.00 23.250 0.375 72.00 48.00 20 908.00 3. For bevel detail see page 107.
or estimated.

LONG RADIUS
Size Schedule
Number
Weight in
Pounds
SCHEDULE XS
O.D. I.D. T V W
1/2 0.84 0.546 0.147 3.00 1.88 80 0.45
3/4 1.05 0.742 0.154 3.00 2.00 80 0.52
1 1.32 0.957 0.179 3.00 2.19 80 0.97
1 1/4 1.66 1.278 0.191 3.75 2.75 80 1.60
1 1/2 1.90 1.500 0.200 4.50 3.25 80 2.20
2 2.38 1.939 0.218 6.00 4.19 80 4.10
2 1/2 2.88 2.323 0.276 7.50 5.19 80 7.70
3 3.50 2.900 0.300 9.00 6.25 80 12.40
3 1/2 4.00 3.364 0.318 10.50 7.25 80 17.10
4 4.50 3.826 0.337 12.00 8.25 80 24.10
5 5.56 4.813 0.375 15.00 10.31 80 41.70
6 6.62 5.761 0.432 18.00 12.31 80 68.20
8 8.62 7.625 0.500 24.00 16.31 80 140.00
10 10.75 9.750 0.500 30.00 20.38 60 217.00
12 12.75 11.750 0.500 36.00 24.38 * 311.00
14 14.00 13.000 0.500 42.00 28.00 * 400.00
16 16.00 15.000 0.500 48.00 32.00 40 540.00 NOTES
24 24.00 23.000 0.500 72.00 48.00 * 1210.00 3. For bevel detail see page 107.
or estimated.
43

180° return bends
LONG RADIUS Outside Inside Wall Center Back Pipe Approx.
Number
Weight in
Pounds
O.D. I.D. T V W
1/2 0.84 0.622 0.109 3.00 1.88 40 0.32
3/4 1.05 0.824 0.113 3.00 2.00 40 0.34
1 1.32 1.054 0.133 3.00 2.19 40 0.74
1 1/4 1.66 1.380 0.140 3.75 2.75 40 1.10
1 1/2 1.90 1.610 0.145 4.50 3.25 40 1.60
2 2.38 2.072 0.154 6.00 4.19 40 3.20
2 1/2 2.88 2.474 0.203 7.50 5.19 40 6.10
3 3.50 3.068 0.216 9.00 6.25 40 9.40
3 1/2 4.00 3.548 0.226 10.50 7.25 40 12.80
4 4.50 4.026 0.237 12.00 8.25 40 17.50
5 5.56 5.044 0.258 15.00 10.31 40 29.30
6 6.62 6.060 0.280 18.00 12.31 40 47.00
8 8.62 7.976 0.322 24.00 16.31 40 87.00
10 10.75 10.020 0.365 30.00 20.38 40 164.00
12 12.75 11.938 0.406 36.00 24.38 40 240.00
FITTINGS
14 14.00 13.124 0.438 42.00 28.00 40 315.00

NOTES 16 16.00 15.000 0.500 48.00 32.00 40 410.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 18 18.00 16.876 0.562 54.00 36.00 40 520.00
2. All dimensions are in inches. 20 20.00 18.812 0.594 60.00 40.00 40 640.00
3. For bevel detail see page 107. 24 24.00 22.624 0.688 72.00 48.00 40 915.00
or estimated.
LONG RADIUS Outside Inside Wall Center Back Pipe Approx.

Number
Weight in
Pounds
O.D. I.D. T V W
1/2 0.84 0.546 0.147 3.00 1.88 80 0.45
3/4 1.05 0.742 0.154 3.00 2.00 80 0.52
1 1.32 0.962 0.179 3.00 2.19 80 0.97
1 1/4 1.66 1.278 0.191 3.75 2.75 80 1.60
1 1/2 1.90 1.500 0.200 4.50 3.25 80 2.20
2 2.38 1.944 0.218 6.00 4.19 80 4.10
2 1/2 2.88 2.328 0.276 7.50 5.19 80 7.70
3 3.50 2.900 0.300 9.00 6.25 80 12.40
3 1/2 4.00 3.364 0.318 10.50 7.25 80 17.10
4 4.50 3.826 0.337 12.00 8.25 80 24.10
5 5.56 4.810 0.375 15.00 10.31 80 41.70
6 6.62 5.756 0.432 18.00 12.31 80 68.20
8 8.62 7.620 0.500 24.00 16.31 80 140.00
10 10.75 9.562 0.594 30.00 20.38 80 220.00
12 12.75 11.374 0.688 36.00 24.38 80 315.00
14 14.00 12.500 0.750 42.00 28.00 80 410.00
NOTES 16 16.00 14.312 0.844 48.00 32.00 80 550.00
or estimated.
44

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 180° return bends

LONG RADIUS
Size Schedule
Number
Weight in
Pounds
SCHEDULE 160
O.D. I.D. T V W
1/2 0.84 0.464 0.188 3.00 1.88 160 0.40
3/4 1.05 0.612 0.219 3.00 2.00 160 0.43
1 1.32 0.820 0.250 3.00 2.19 160 0.93
1 1/4 1.66 1.160 0.250 3.75 2.75 160 1.38
1 1/2 1.90 1.338 0.281 4.50 3.25 160 2.00
2 2.38 1.692 0.344 6.00 4.19 160 4.00
2 1/2 2.88 2.130 0.375 7.50 5.19 160 7.63
3 3.50 2.624 0.438 9.00 6.25 160 11.75
4 4.50 3.438 0.531 12.00 8.25 160 21.88
5 5.56 4.310 0.625 15.00 10.31 160 36.63
6 6.62 5.182 0.719 18.00 12.31 160 58.75
8 8.62 6.808 0.906 24.00 16.31 160 108.75
10 10.75 8.500 1.125 30.00 20.38 160 205.00
12 12.75 10.126 1.312 36.00 24.38 160 296.25
14 14.00 11.188 1.406 42.00 28.00 160 388.75
FITTINGS
16 16.00 12.812 1.594 48.00 32.00 160 510.00
18 18.00 14.438 1.781 54.00 36.00 160 642.50 NOTES
20 20.00 16.062 1.969 60.00 40.00 160 795.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
or estimated.

LONG RADIUS
Size Schedule
Number
Weight in
Pounds
SCHEDULE XXS
O.D. I.D. T V W
1/2 0.84 0.252 0.294 3.00 1.88 * 0.44
3/4 1.05 0.434 0.308 3.00 2.00 * 0.47
1 1.32 0.604 0.358 3.00 2.19 * 1.02
1 1/4 1.66 0.896 0.382 3.75 2.75 * 1.51
1 1/2 1.90 1.100 0.400 4.50 3.25 * 2.20
2 2.38 1.508 0.436 6.00 4.19 * 4.40
2 1/2 2.88 1.776 0.552 7.50 5.19 * 8.39
3 3.50 2.300 0.600 9.00 6.25 * 12.93
4 4.50 3.152 0.674 12.00 8.25 * 24.06
5 5.56 4.060 0.750 15.00 10.31 * 40.29
6 6.62 4.892 0.864 18.00 12.31 * 64.63
8 8.62 6.870 0.875 24.00 16.31 * 119.63
10 10.75 8.750 1.000 30.00 20.38 140 225.50
12 12.75 10.750 1.000 36.00 24.38 120 325.88
NOTES
or estimated.
45

180° return bends
SHORT RADIUS Outside Inside Wall Center Back Pipe Approx.
Number
Weight in
Pounds
O.D. I.D. T V W
1 1.32 1.049 0.133 2.00 1.62 40 0.50
1 1/4 1.66 1.380 0.140 2.50 2.06 40 0.80
1 1/2 1.90 1.610 0.145 3.00 2.44 40 1.10
2 2.38 2.067 0.154 4.00 3.19 40 1.90
2 1/2 2.88 2.469 0.203 5.00 3.94 40 4.00
3 3.50 3.068 0.216 6.00 4.75 40 6.00
3 1/2 4.00 3.548 0.226 7.00 5.50 40 8.70
4 4.50 4.026 0.237 8.00 6.25 40 12.20
5 5.56 5.047 0.258 10.00 7.75 40 19.20
6 6.62 6.065 0.280 12.00 9.31 40 32.90
8 8.62 7.981 0.322 16.00 12.31 40 64.90
10 10.75 10.020 0.365 20.00 15.38 40 112.00
12 12.75 12.000 0.375 24.00 18.38 * 157.00
14 14.00 13.250 0.375 28.00 21.00 30 208.00
16 16.00 15.250 0.375 32.00 24.00 30 257.00
FITTINGS
18 18.00 17.250 0.375 36.00 27.00 * 325.00

NOTES 20 20.00 19.250 0.375 40.00 30.00 20 416.00
or estimated.

Number
Weight in
Pounds
O.D. I.D. T V W
1 1.32 0.962 0.179 2.00 1.62 80 0.70
1 1/4 1.66 1.278 0.191 2.50 2.06 80 1.00
1 1/2 1.90 1.500 0.200 3.00 2.44 80 1.50
2 2.38 1.939 0.218 4.00 3.19 80 2.90
2 1/2 2.88 2.323 0.276 5.00 3.94 80 5.20
3 3.50 2.900 0.300 6.00 4.75 80 8.20
3 1/2 4.00 3.364 0.318 7.00 5.50 80 11.70
4 4.50 3.826 0.337 8.00 6.25 80 16.40
5 5.56 4.813 0.375 10.00 7.75 80 27.70
6 6.62 5.761 0.432 12.00 9.31 80 45.70
8 8.62 7.625 0.500 16.00 12.31 80 96.30
10 10.75 9.750 0.500 20.00 15.38 60 143.00
12 12.75 11.750 0.500 24.00 18.38 * 212.00
14 14.00 13.000 0.500 28.00 21.00 * 271.00
16 16.00 15.000 0.500 32.00 24.00 40 339.00
18 18.00 17.000 0.500 36.00 27.00 * 425.00
NOTES 20 20.00 19.000 0.500 40.00 30.00 30 555.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 24 24.00 23.000 0.500 48.00 36.00 * 778.00
or estimated.
46

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com 180° return bends

SHORT RADIUS
Size Schedule
Number
Weight in
Pounds
SCHEDULE 40
O.D. I.D. T V W
1 1.32 1.054 0.133 2.00 1.62 40 0.50
1 1/4 1.66 1.380 0.140 2.50 2.06 40 0.80
1 1/2 1.90 1.610 0.145 3.00 2.44 40 1.10
2 2.38 2.072 0.154 4.00 3.19 40 1.90
2 1/2 2.88 2.474 0.203 5.00 3.94 40 4.00
3 3.50 3.068 0.216 6.00 4.75 40 6.00
3 1/2 4.00 3.548 0.226 7.00 5.50 40 8.70
4 4.50 4.026 0.237 8.00 6.25 40 12.20
5 5.56 5.044 0.258 10.00 7.75 40 19.20
6 6.62 6.060 0.280 12.00 9.31 40 32.90
8 8.62 7.976 0.322 16.00 12.31 40 64.90
10 10.75 10.020 0.365 20.00 15.38 40 112.00
12 12.75 11.938 0.406 24.00 18.38 40 165.00
14 14.00 13.124 0.438 28.00 21.00 40 215.00
16 16.00 15.000 0.500 32.00 24.00 40 265.00
FITTINGS
18 18.00 16.876 0.562 36.00 27.00 40 335.00
20 20.00 18.812 0.594 40.00 30.00 40 425.00 NOTES
or estimated.

SHORT RADIUS
Size Schedule
Number
Weight in
Pounds
SCHEDULE 80
O.D. I.D. T V W
1 1.32 0.962 0.179 2.00 1.62 80 0.70
1 1/4 1.66 1.278 0.191 2.50 2.06 80 1.00
1 1/2 1.90 1.500 0.200 3.00 2.44 80 1.50
2 2.38 1.944 0.218 4.00 3.19 80 2.90
2 1/2 2.88 2.328 0.276 5.00 3.94 80 5.20
3 3.50 2.900 0.300 6.00 4.75 80 8.20
3 1/2 4.00 3.364 0.318 7.00 5.50 80 11.70
4 4.50 3.826 0.337 8.00 6.25 80 16.40
5 5.56 4.810 0.375 10.00 7.75 80 27.70
6 6.62 5.756 0.432 12.00 9.31 80 45.70
8 8.62 7.620 0.500 16.00 12.31 80 96.30
10 10.75 9.562 0.594 20.00 15.38 80 160.00
12 12.75 11.374 0.688 24.00 18.38 80 225.00
14 14.00 12.500 0.750 28.00 21.00 80 280.00
16 16.00 14.312 0.844 32.00 24.00 80 350.00
18 18.00 16.124 0.938 36.00 27.00 80 435.00
20 20.00 17.938 1.031 40.00 30.00 80 570.00 NOTES
or estimated.
47

180° return bends
Number
Weight in
Pounds
O.D. I.D. T V W
1 1.32 0.820 0.250 2.00 1.62 160 0.85
1 1/4 1.66 1.160 0.250 2.50 2.06 160 1.21
1 1/2 1.90 1.338 0.281 3.00 2.44 160 1.82
2 2.38 1.692 0.344 4.00 3.19 160 3.51
2 1/2 2.88 2.130 0.375 5.00 3.94 160 6.29
3 3.50 2.624 0.438 6.00 4.75 160 9.92
4 4.50 3.438 0.531 8.00 6.25 160 19.84
5 5.56 4.310 0.625 10.00 7.75 160 33.52
6 6.62 5.182 0.719 12.00 9.31 160 55.30
8 8.62 6.808 0.906 16.00 12.31 160 116.52
10 10.75 8.500 1.125 20.00 15.38 160 173.03
12 12.75 10.126 1.312 24.00 18.38 160 256.52
14 14.00 11.188 1.406 28.00 21.00 160 327.91
16 16.00 12.812 1.594 32.00 24.00 160 410.19
18 18.00 14.438 1.781 36.00 27.00 160 514.25
FITTINGS
20 20.00 16.062 1.969 40.00 30.00 160 671.55

NOTES 24 24.00 19.312 2.344 48.00 36.00 160 941.38
or estimated.

Number
Weight in
Pounds
O.D. I.D. T V W
1 1.32 0.604 0.358 2.00 1.62 * 0.93
1 1/4 1.66 0.896 0.382 2.50 2.06 * 1.33
1 1/2 1.90 1.100 0.400 3.00 2.44 * 2.00
2 2.38 1.508 0.436 4.00 3.19 * 3.90
2 1/2 2.88 1.776 0.552 5.00 3.94 * 6.92
3 3.50 2.300 0.600 6.00 4.75 * 10.91
4 4.50 3.152 0.674 8.00 6.25 * 21.83
5 5.56 4.060 0.750 10.00 7.75 * 36.87
6 6.62 4.892 0.864 12.00 9.31 * 60.83
8 8.62 6.870 0.875 16.00 12.31 * 128.18
10 10.75 8.750 1.000 20.00 15.38 140 190.33
12 12.75 10.750 1.000 24.00 18.38 120 282.17
NOTES
or estimated.
48

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com straight tees
Outside Inside Wall Center Center Pipe Approx.

SCHEDULE STD
Pipe Diameter Diameter Thickness to Center to End Schedule Weight in
Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.622 0.109 1.00 1.00 40 0.35
3/4 1.05 0.824 0.113 1.12 1.12 40 0.50
1 1.32 1.049 0.133 1.50 1.50 40 0.75
1 1/4 1.66 1.380 0.140 1.88 1.88 40 1.30
1 1/2 1.90 1.610 0.145 2.25 2.25 40 1.90
2 2.38 2.067 0.154 2.50 2.50 40 3.20
2 1/2 2.88 2.469 0.203 3.00 3.00 40 5.80
3 3.50 3.068 0.216 3.38 3.38 40 7.20
3 1/2 4.00 3.548 0.226 3.75 3.75 40 9.50
4 4.50 4.026 0.237 4.12 4.12 40 12.70
5 5.56 5.047 0.258 4.88 4.88 40 20.80
6 6.62 6.065 0.280 5.62 5.62 40 33.10
8 8.62 7.981 0.322 7.00 7.00 40 56.50
10 10.75 10.020 0.365 8.50 8.50 40 90.90
12 12.75 12.000 0.375 10.00 10.00 * 136.00
FITTINGS
14 14.00 13.250 0.375 11.00 11.00 30 162.00
16 16.00 15.250 0.375 12.00 12.00 30 206.00 NOTES
24 24.00 23.250 0.375 17.00 17.00 20 508.00 3. For bevel detail see page 107.
30 30.00 29.250 0.375 22.00 22.00 * 835.00 5. For sizes larger than 48" please call.
36 36.00 35.250 0.375 26.50 26.50 * 1294.00 6. All weights are in pounds and approximated
42 42.00 41.250 0.375 30.00 28.00 * 1495.00 or estimated.
48 48.00 47.250 0.375 35.00 33.00 * 2300.00 to any pipe schedule number.

SCHEDULE XS
Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.546 0.147 1.00 1.00 80 0.37
3/4 1.05 0.742 0.154 1.12 1.12 80 0.58
1 1.32 0.957 0.179 1.50 1.50 80 0.87
1 1/4 1.66 1.278 0.191 1.88 1.88 80 1.60
1 1/2 1.90 1.500 0.200 2.25 2.25 80 2.30
2 2.38 1.939 0.218 2.50 2.50 80 3.90
2 1/2 2.88 2.323 0.276 3.00 3.00 80 6.50
3 3.50 2.900 0.300 3.38 3.38 80 9.00
3 1/2 4.00 3.364 0.318 3.75 3.75 80 12.20
4 4.50 3.826 0.337 4.12 4.12 80 16.20
5 5.56 4.813 0.375 4.88 4.88 80 26.60
6 6.62 5.761 0.432 5.62 5.62 80 41.80
8 8.62 7.625 0.500 7.00 7.00 80 76.20
10 10.75 9.750 0.500 8.50 8.50 60 115.00
12 12.75 11.750 0.500 10.00 10.00 * 169.00
14 14.00 13.000 0.500 11.00 11.00 * 237.00
16 16.00 15.000 0.500 12.00 12.00 40 284.00 NOTES
24 24.00 23.000 0.500 17.00 17.00 * 625.00 3. For bevel detail see page 107.
30 30.00 29.000 0.500 22.00 22.00 20 1065.00 5. For sizes larger than 48" please call.
36 36.00 35.000 0.500 26.50 26.50 20 1610.00 6. All weights are in pounds and approximated
42 42.00 41.000 0.500 30.00 28.00 * 1788.00 or estimated.
48 48.00 47.000 0.500 35.00 33.00 * 2300.00 to any pipe schedule number.
49

straight tees
Schedule 40 Outside Inside Wall Center Center Pipe Approx.
Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.622 0.109 1.00 1.00 40 0.35
3/4 1.05 0.824 0.113 1.12 1.12 40 0.50
1 1.32 1.054 0.133 1.50 1.50 40 0.75
1 1/4 1.66 1.380 0.140 1.88 1.88 40 1.30
1 1/2 1.90 1.610 0.145 2.25 2.25 40 1.90
2 2.38 2.072 0.154 2.50 2.50 40 3.20
2 1/2 2.88 2.474 0.203 3.00 3.00 40 5.80
3 3.50 3.068 0.216 3.38 3.38 40 7.20
3 1/2 4.00 3.548 0.226 3.75 3.75 40 8.50
4 4.50 4.026 0.237 4.12 4.12 40 9.50
5 5.56 5.044 0.258 4.88 4.88 40 12.70
6 6.62 6.060 0.280 5.62 5.62 40 20.80
8 8.62 7.976 0.322 7.00 7.00 40 33.10
10 10.75 10.020 0.365 8.50 8.50 40 56.50
12 12.75 11.938 0.406 10.00 10.00 40 90.90
FITTINGS
14 14.00 13.124 0.438 11.00 11.00 40 165.00

NOTES 16 16.00 15.000 0.500 12.00 12.00 40 210.00
or estimated.
SCHEDULE 80 Outside Inside Wall Center Center Pipe Approx.

Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.546 0.147 1.00 1.00 80 0.37
3/4 1.05 0.742 0.154 1.12 1.12 80 0.58
1 1.32 0.962 0.179 1.50 1.50 80 0.87
1 1/4 1.66 1.278 0.191 1.88 1.88 80 1.60
1 1/2 1.90 1.500 0.200 2.25 2.25 80 2.30
2 2.38 1.944 0.218 2.50 2.50 80 3.90
2 1/2 2.88 2.328 0.276 3.00 3.00 80 6.50
3 3.50 2.900 0.300 3.38 3.38 80 9.00
3 1/2 4.00 3.364 0.318 3.75 3.75 80 12.20
4 4.50 3.826 0.337 4.12 4.12 80 16.20
5 5.56 4.810 0.375 4.88 4.88 80 26.60
6 6.62 5.756 0.432 5.62 5.62 80 41.80
8 8.62 7.620 0.500 7.00 7.00 80 76.20
10 10.75 9.562 0.594 8.50 8.50 80 120.00
12 12.75 11.374 0.688 10.00 10.00 80 175.00
14 14.00 12.500 0.750 11.00 11.00 80 240.00
NOTES 16 16.00 14.312 0.844 12.00 12.00 80 290.00
or estimated.
50

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com straight tees

Schedule 160
Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.464 0.188 1.00 1.00 160 0.46
3/4 1.05 0.612 0.219 1.12 1.12 160 0.73
1 1.32 0.820 0.250 1.50 1.50 160 1.09
1 1/4 1.66 1.160 0.250 1.88 1.88 160 2.00
1 1/2 1.90 1.338 0.281 2.25 2.25 160 2.88
2 2.38 1.692 0.344 2.50 2.50 160 4.88
2 1/2 2.88 2.130 0.375 3.00 3.00 160 8.13
3 3.50 2.624 0.438 3.38 3.38 160 11.25
4 4.50 3.438 0.531 4.12 4.12 160 20.25
5 5.56 4.310 0.625 4.88 4.88 160 33.25
6 6.62 5.182 0.719 5.62 5.62 160 52.25
8 8.62 6.808 0.906 7.00 7.00 160 95.25
10 10.75 8.500 1.125 8.50 8.50 160 143.75
12 12.75 10.126 1.312 10.00 10.00 160 211.25
14 14.00 11.188 1.406 11.00 11.00 160 296.25
FITTINGS
16 16.00 12.812 1.594 12.00 12.00 160 355.00
18 18.00 14.438 1.781 13.50 13.50 160 441.25 NOTES
or estimated.

SCHEDULE XXS
Size Number Pounds
O.D. I.D. T R B
1/2 0.84 0.252 0.294 1.00 1.00 * 0.51
3/4 1.05 0.434 0.308 1.12 1.12 * 0.80
1 1.32 0.604 0.358 1.50 1.50 * 1.20
1 1/4 1.66 0.896 0.382 1.88 1.88 * 2.20
1 1/2 1.90 1.100 0.400 2.25 2.25 * 3.16
2 2.38 1.508 0.436 2.50 2.50 * 5.36
2 1/2 2.88 1.776 0.552 3.00 3.00 * 8.94
3 3.50 2.300 0.600 3.38 3.38 * 12.38
4 4.50 3.152 0.674 4.12 4.12 * 22.28
5 5.56 4.060 0.750 4.88 4.88 * 36.58
6 6.62 4.892 0.864 5.62 5.62 * 57.48
8 8.62 6.870 0.875 7.00 7.00 * 104.78
10 10.75 8.750 1.000 8.50 8.50 140 158.13
12 12.75 10.750 1.000 10.00 10.00 120 232.38
NOTES
or estimated.
51

reducing tees
SCHEDULE STD NOTES
or estimated.
paragraph 4.4.2.
DIMENSIONS OF RUN DIMENSIONS OF BRANCH

Pipe Outside Inside Wall Center Outside Inside Wall Center Pipe Approx.
Size Diameter Diameter Thickness to End Diameter Diameter Thickness to End Schedule Weight in
Number Pounds
O.D. I.D. T R O.D. I.D. T B
3/4 x 1/2 1.05 0.824 0.113 1.12 0.84 0.622 0.109 1.12 40 0.41
1 x 3/4 1.32 1.049 0.133 1.50 1.05 0.824 0.113 1.50 40 0.81
1 x 1/2 1.32 1.049 0.133 1.50 0.84 0.622 0.109 1.50 40 0.78
1 1/4 x 1 1.66 1.380 0.140 1.88 1.32 1.049 0.133 1.88 40 1.30
1 1/4 x 3/4 1.66 1.380 0.140 1.88 1.05 0.824 0.113 1.88 40 1.30
FITTINGS
1 1/4 x 1/2 1.66 1.380 0.140 1.88 0.84 0.622 0.109 1.88 40 1.30
1 1/2 x 1 1/4 1.90 1.610 0.145 2.25 1.66 1.380 0.140 2.25 40 2.00
1 1/2 x 1 1.90 1.610 0.145 2.25 1.32 1.049 0.133 2.25 40 1.90
1 1/2 x 3/4 1.90 1.610 0.145 2.25 1.05 0.824 0.113 2.25 40 1.80
1 1/2 x 1/2 1.90 1.610 0.145 2.25 0.84 0.622 0.109 2.25 40 1.80
2 x 1 1/2 2.38 2.067 0.154 2.50 1.90 1.610 0.145 2.38 40 3.10
2 x 1 1/4 2.38 2.067 0.154 2.50 1.66 1.380 0.140 2.25 40 3.00
2x1 2.38 2.067 0.154 2.50 1.32 1.049 0.133 2.00 40 2.80
2 x 3/4 2.38 2.067 0.154 2.50 1.05 0.824 0.113 1.75 40 2.50
2 1/2 x 2 2.88 2.469 0.203 3.00 2.38 2.067 0.154 2.75 40 5.40
2 1/2 x 1 1/2 2.88 2.469 0.203 3.00 1.90 1.610 0.145 2.62 40 5.10
2 1/2 x 1 1/4 2.88 2.469 0.203 3.00 1.66 1.380 0.140 2.50 40 4.80
2 1/2 x 1 2.88 2.469 0.203 3.00 1.32 1.049 0.133 2.25 40 4.60
3 x 2 1/2 3.50 3.068 0.216 3.38 2.88 2.469 0.203 3.25 40 7.20
3x2 3.50 3.068 0.216 3.38 2.38 2.067 0.154 3.00 40 7.00
3 x 1 1/2 3.50 3.068 0.216 3.38 1.90 1.610 0.145 2.88 40 6.80
3 x 1 1/4 3.50 3.068 0.216 3.38 1.66 1.380 0.140 2.75 40 6.60
❖3x1 3.50 3.068 0.216 3.38 1.32 1.049 0.133 2.62 40 6.50
3 1/2 x 3 4.00 3.548 0.226 3.75 3.50 3.068 0.216 3.62 40 9.80
3 1/2 x 2 1/2 4.00 3.548 0.226 3.75 2.88 2.474 0.203 3.50 40 9.40
3 1/2 x 2 4.00 3.548 0.226 3.75 2.38 2.072 0.154 3.25 40 9.20
3 1/2 x 1 1/2 4.00 3.548 0.226 3.75 1.90 1.610 0.145 3.12 40 8.90
4 x 3 1/2 4.50 4.026 0.237 4.12 4.00 3.548 0.226 4.00 40 11.90
4x3 4.50 4.026 0.237 4.12 3.50 3.068 0.216 3.88 40 11.60
4 x 2 1/2 4.50 4.026 0.237 4.12 2.88 2.469 0.203 3.75 40 11.40
4x2 4.50 4.026 0.237 4.12 2.38 2.067 0.154 3.50 40 11.20
4 x 1 1/2 4.50 4.026 0.237 4.12 1.90 1.610 0.145 3.38 40 11.20
5x4 5.56 5.047 0.258 4.88 4.50 4.026 0.237 4.62 40 20.50
5 x 3 1/2 5.56 5.047 0.258 4.88 4.00 3.548 0.226 4.50 40 20.00
5x3 5.56 5.047 0.258 4.88 3.50 3.068 0.216 4.38 40 19.40
5 x 2 1/2 5.56 5.047 0.258 4.88 2.88 2.469 0.203 4.25 40 19.00
5x2 5.56 5.047 0.258 4.88 2.38 2.067 0.154 4.12 40 18.80
6x5 6.62 6.065 0.280 5.62 5.56 5.047 0.258 5.38 40 32.00
6x4 6.62 6.065 0.280 5.62 4.50 4.026 0.237 5.12 40 30.50
6 x 3 1/2 6.62 6.065 0.280 5.62 4.00 3.548 0.226 5.00 40 30.00
6x3 6.62 6.065 0.280 5.62 3.50 3.068 0.216 4.88 40 30.00
6 x 2 1/2 6.62 6.065 0.280 5.62 2.88 2.469 0.203 4.75 40 29.70
❖6x2 6.62 6.065 0.280 5.62 2.38 2.067 0.154 4.75 40 29.00
8x6 8.62 7.981 0.322 7.00 6.62 6.065 0.280 6.62 40 56.50
52
8x5 8.62 7.981 0.322 7.00 5.56 5.047 0.258 6.38 40 54.00
8x4 8.62 7.981 0.322 7.00 4.50 4.026 0.237 6.12 40 53.20
TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com reducing tees

Number Pounds
8 x 3 1/2 8.62 7.981 0.322 7.00 4.00 3.548 0.226 6.00 40 53.00
❖8x3 8.62 7.981 0.322 7.00 3.50 3.068 0.216 6.00 40 52.00
10 x 8 10.75 10.020 0.365 8.50 8.62 7.981 0.322 8.00 40 86.50
10 x 6 10.75 10.020 0.365 8.50 6.62 6.060 0.280 7.62 40 85.90
10 x 5 10.75 10.020 0.365 8.50 5.56 5.047 0.258 7.50 40 82.50
10 x 4 10.75 10.020 0.365 8.50 4.50 4.026 0.237 7.25 40 82.00
❖ 10 x 3 10.75 10.020 0.365 8.50 3.50 3.068 0.216 7.25 40 79.00
12 x 10 12.75 12.000 0.375 10.00 10.75 10.020 0.365 9.50 * 123.00
12 x 8 12.75 12.000 0.375 10.00 8.62 7.981 0.322 9.00 * 120.00
12 x 6 12.75 12.000 0.375 10.00 6.62 6.060 0.280 8.62 * 118.00
12 x 5 12.75 12.000 0.375 10.00 5.56 5.047 0.258 8.50 * 117.00
❖ 12 x 4 12.75 12.000 0.375 10.00 4.50 4.026 0.237 8.50 * 112.00
14 x 12 14.00 13.250 0.375 11.00 12.75 12.000 0.375 10.62 * 151.00
14 x 10 14.00 13.250 0.375 11.00 10.75 10.020 0.365 10.12 * 148.00
FITTINGS
14 x 8 14.00 13.250 0.375 11.00 8.62 7.981 0.322 9.75 * 146.00
14 x 6 14.00 13.250 0.375 11.00 6.62 6.065 0.280 9.38 * 145.00
16 x 14 16.00 15.250 0.375 12.00 14.00 13.250 0.375 12.00 * 221.00
16 x 12 16.00 15.250 0.375 12.00 12.75 12.000 0.375 11.62 * 213.00
16 x 10 16.00 15.250 0.375 12.00 10.75 10.020 0.365 11.12 * 197.00
16 x 8 16.00 15.250 0.375 12.00 8.62 7.981 0.322 10.75 * 190.00
16 x 6 16.00 15.250 0.375 12.00 6.62 6.060 0.280 10.38 * 180.00
18 x 16 18.00 17.250 0.375 13.50 16.00 15.250 0.375 13.00 * 262.00
18 x 14 18.00 17.250 0.375 13.50 14.00 13.250 0.375 13.00 * 248.00
18 x 12 18.00 17.250 0.375 13.50 12.75 12.000 0.375 12.62 * 241.00
18 x 10 18.00 17.250 0.375 13.50 10.75 10.020 0.365 12.12 * 229.00
18 x 8 18.00 17.250 0.375 13.50 8.62 7.981 0.322 11.75 * 216.00
20 x 18 20.00 19.250 0.375 15.00 18.00 17.250 0.375 14.50 * 352.00
20 x 16 20.00 19.250 0.375 15.00 16.00 15.250 0.375 14.00 * 339.00
20 x 14 20.00 19.250 0.375 15.00 14.00 13.250 0.375 14.00 * 327.00
20 x 12 20.00 19.250 0.375 15.00 12.75 12.000 0.375 13.62 * 315.00
20 x 10 20.00 19.250 0.375 15.00 10.75 10.020 0.365 13.12 * 305.00
20 x 8 20.00 19.250 0.375 15.00 8.62 7.976 0.322 12.75 * 293.00
24 x 20 24.00 23.250 0.375 17.00 20.00 19.250 0.375 17.00 * 500.00
24 x 18 24.00 23.250 0.375 17.00 18.00 17.250 0.375 16.50 * 487.00
24 x 16 24.00 23.250 0.375 17.00 16.00 15.250 0.375 16.00 * 475.00
24 x 14 24.00 23.250 0.375 17.00 14.00 13.250 0.375 16.00 * 465.00
24 x 12 24.00 23.250 0.375 17.00 12.75 12.000 0.375 15.62 * 450.00
24 x 10 24.00 23.250 0.375 17.00 10.75 10.020 0.365 15.12 * 447.00
30 x 24 30.00 29.250 0.375 22.00 24.00 23.250 0.375 21.00 * 795.00
30 x 20 30.00 29.250 0.375 22.00 20.00 19.250 0.375 20.00 * 749.00
30 x 18 30.00 29.250 0.375 22.00 18.00 17.250 0.375 19.50 * 727.00
30 x 16 30.00 29.250 0.375 22.00 16.00 15.250 0.375 19.00 * 715.00
36 x 30 36.00 35.250 0.375 26.50 30.00 29.250 0.375 25.00 * 1207.00
36 x 24 36.00 35.250 0.375 26.50 24.00 23.250 0.375 24.00 * 1129.00
36 x 20 36.00 35.250 0.375 26.50 20.00 19.250 0.375 23.00 * 1072.00
36 x 18 36.00 35.250 0.375 26.50 18.00 17.250 0.375 22.50 * 1136.00
42 x 36 42.00 41.250 0.375 30.00 36.00 35.250 0.375 28.00 * 1415.00
42 x 30 42.00 41.250 0.375 30.00 30.00 29.250 0.375 28.00 * 1327.00
42 x 24 42.00 41.250 0.375 30.00 24.00 23.250 0.375 26.00 * 1248.00
42 x 20 42.00 41.250 0.375 30.00 20.00 19.250 0.375 26.00 * 1200.00
48 x 42 48.00 47.250 0.375 35.00 42.00 41.250 0.375 32.00 * 2207.00
48 x 36 48.00 47.250 0.375 35.00 36.00 35.250 0.375 31.00 * 2127.00
48 x 30 48.00 47.250 0.375 35.00 30.00 29.250 0.375 30.00 * 2048.00
48 x 24 48.00 47.250 0.375 35.00 24.00 23.250 0.375 29.00 * 1900.00
53

reducing tees
SCHEDULE XS NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
3/4 x 1/2 1.05 0.742 0.154 1.12 0.84 0.546 0.147 1.12 80 0.47
1 x 3/4 1.32 0.957 0.179 1.50 1.05 0.742 0.154 1.50 80 0.98
1 x 1/2 1.32 0.957 0.179 1.50 0.84 0.546 0.147 1.50 80 0.92
1 1/4 x 1 1.66 1.278 0.191 1.88 1.32 0.957 0.179 1.88 80 1.60
1 1/4 x 3/4 1.66 1.278 0.191 1.88 1.05 0.742 0.154 1.88 80 1.60
FITTINGS
1 1/4 x 1/2 1.66 1.278 0.191 1.88 0.84 0.546 0.147 1.88 80 1.60
1 1/2 x 1 1/4 1.90 1.500 0.200 2.25 1.66 1.278 0.191 2.25 80 2.40
1 1/2 x 1 1.90 1.500 0.200 2.25 1.32 0.957 0.179 2.25 80 2.30
1 1/2 x 3/4 1.90 1.500 0.200 2.25 1.05 0.742 0.154 2.25 80 2.20
1 1/2 x 1/2 1.90 1.500 0.200 2.25 0.84 0.546 0.147 2.25 80 2.20
2 x 1 1/2 2.38 1.944 0.218 2.50 1.90 1.500 0.200 2.38 80 3.80
2 x 1 1/4 2.38 1.944 0.218 2.50 1.66 1.278 0.191 2.25 80 3.70
2x1 2.38 1.944 0.218 2.50 1.32 0.957 0.179 2.00 80 3.50
2 x 3/4 2.38 1.944 0.218 2.50 1.05 0.742 0.154 1.75 80 3.50
2 1/2 x 2 2.88 2.323 0.276 3.00 2.38 1.944 0.218 2.75 80 6.30
2 1/2 x 1 1/2 2.88 2.323 0.276 3.00 1.90 1.500 0.200 2.62 80 6.20
2 1/2 x 1 1/4 2.88 2.323 0.276 3.00 1.66 1.278 0.191 2.50 80 6.00
2 1/2 x 1 2.88 2.323 0.276 3.00 1.32 0.957 0.179 2.25 80 5.80
3 x 2 1/2 3.50 2.900 0.300 3.38 2.88 2.323 0.276 3.25 80 8.80
3x2 3.50 2.900 0.300 3.38 2.38 1.939 0.218 3.00 80 8.60
3 x 1 1/2 3.50 2.900 0.300 3.38 1.90 1.500 0.200 2.88 80 8.10
3 x 1 1/4 3.50 2.900 0.300 3.38 1.66 1.278 0.191 2.75 80 8.00
❖3x1 3.50 2.900 0.300 3.38 1.32 0.957 0.179 2.62 80 7.80
3 1/2 x 3 4.00 3.364 0.318 3.75 3.50 2.900 0.300 3.62 80 12.60
3 1/2 x 2 1/2 4.00 3.364 0.318 3.75 2.88 2.323 0.276 3.50 80 12.10
3 1/2 x 2 4.00 3.364 0.318 3.75 2.38 1.939 0.218 3.25 80 11.70
3 1/2 x 1 1/2 4.00 3.364 0.318 3.75 1.90 1.500 0.200 3.12 80 11.60
4 x 3 1/2 4.50 3.826 0.337 4.12 4.00 3.364 0.318 4.00 80 15.70
4x3 4.50 3.826 0.337 4.12 3.50 2.900 0.300 3.88 80 15.40
4 x 2 1/2 4.50 3.826 0.337 4.12 2.88 2.323 0.276 3.75 80 15.10
4x2 4.50 3.826 0.337 4.12 2.38 1.939 0.218 3.50 80 15.10
4 x 1 1/2 4.50 3.826 0.337 4.12 1.90 1.500 0.200 3.38 80 15.00
5x4 5.56 4.813 0.375 4.88 4.50 3.826 0.337 4.62 80 25.40
5 x 3 1/2 5.56 4.813 0.375 4.88 4.00 3.364 0.318 4.50 80 24.80
5x3 5.56 4.813 0.375 4.88 3.50 2.900 0.300 4.38 80 24.20
5 x 2 1/2 5.56 4.813 0.375 4.88 2.88 2.323 0.276 4.25 80 23.90
5x2 5.56 4.813 0.375 4.88 2.38 1.939 0.218 4.12 80 23.60
6x5 6.62 5.761 0.432 5.62 5.56 4.813 0.375 5.38 80 39.50
6x4 6.62 5.761 0.432 5.62 4.50 3.826 0.337 5.12 80 39.30
6 x 3 1/2 6.62 5.761 0.432 5.62 4.00 3.364 0.318 5.00 80 38.80
6x3 6.62 5.761 0.432 5.62 3.50 2.900 0.300 4.88 80 38.60
6 x 2 1/2 6.62 5.761 0.432 5.62 2.88 2.323 0.276 4.75 80 38.20
❖6x2 6.62 5.761 0.432 5.62 2.38 1.939 0.218 4.75 80 37.40
8x6 8.62 7.625 0.500 7.00 6.62 5.761 0.432 6.62 80 70.20
8x5 8.62 7.625 0.500 7.00 5.56 4.813 0.375 6.38 80 69.40
54
8x4 8.62 7.625 0.500 7.00 4.50 3.826 0.337 6.12 80 69.20
TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
8 x 3 1/2 8.62 7.625 0.500 7.00 4.00 3.364 0.318 6.00 80 68.60
❖8x3 8.62 7.625 0.500 7.00 3.50 2.900 0.300 6.00 80 68.30
10 x 8 10.75 9.750 0.500 8.50 8.62 7.620 0.500 8.00 * 107.00
10 x 6 10.75 9.750 0.500 8.50 6.62 5.761 0.432 7.62 * 104.00
10 x 5 10.75 9.750 0.500 8.50 5.56 4.813 0.375 7.50 * 103.00
10 x 4 10.75 9.750 0.500 8.50 4.50 3.826 0.337 7.25 * 101.00
❖ 10 x 3 10.75 9.750 0.500 8.50 3.50 2.900 0.300 7.25 * 99.00
12 x 10 12.75 11.750 0.500 10.00 10.75 9.750 0.500 9.50 * 165.00
12 x 8 12.75 11.750 0.500 10.00 8.62 7.625 0.500 9.00 * 156.00
12 x 6 12.75 11.750 0.500 10.00 6.62 5.761 0.432 8.62 * 151.00
12 x 5 12.75 11.750 0.500 10.00 5.56 4.813 0.375 8.50 * 149.00
❖ 12 x 4 12.75 11.750 0.500 10.00 4.50 3.826 0.337 8.50 * 148.00
14 x 12 14.00 13.000 0.500 11.00 12.75 11.750 0.500 10.62 * 210.00
14 x 10 14.00 13.000 0.500 11.00 10.75 9.750 0.500 10.12 * 203.00
FITTINGS
14 x 8 14.00 13.000 0.500 11.00 8.62 7.625 0.500 9.75 * 200.00
14 x 6 14.00 13.000 0.500 11.00 6.62 5.761 0.432 9.38 * 196.00
16 x 14 16.00 15.000 0.500 12.00 14.00 13.000 0.500 12.00 * 268.00
16 x 12 16.00 15.000 0.500 12.00 12.75 11.750 0.500 11.62 * 261.00
16 x 10 16.00 15.000 0.500 12.00 10.75 9.750 0.500 11.12 * 250.00
16 x 8 16.00 15.000 0.500 12.00 8.62 7.625 0.500 10.75 * 240.00
16 x 6 16.00 15.000 0.500 12.00 6.62 5.761 0.432 10.38 * 235.00
18 x 16 18.00 17.000 0.500 13.50 16.00 15.000 0.500 13.00 * 348.00
18 x 14 18.00 17.000 0.500 13.50 14.00 13.000 0.500 13.00 * 335.00
18 x 12 18.00 17.000 0.500 13.50 12.75 11.750 0.500 12.62 * 328.00
18 x 10 18.00 17.000 0.500 13.50 10.75 9.750 0.500 12.12 * 308.00
18 x 8 18.00 17.000 0.500 13.50 8.62 7.625 0.500 11.75 * 300.00
20 x 18 20.00 19.000 0.500 15.00 18.00 17.000 0.500 14.50 * 445.00
20 x 16 20.00 19.000 0.500 15.00 16.00 15.000 0.500 14.00 * 427.00
20 x 14 20.00 19.000 0.500 15.00 14.00 13.000 0.500 14.00 * 412.00
20 x 12 20.00 19.000 0.500 15.00 12.75 11.750 0.500 13.62 * 397.00
20 x 10 20.00 19.000 0.500 15.00 10.75 9.750 0.500 13.12 * 384.00
20 x 8 20.00 19.000 0.500 15.00 8.62 7.625 0.500 12.75 * 375.00
24 x 20 24.00 23.000 0.500 17.00 20.00 19.000 0.500 17.00 * 610.00
24 x 18 24.00 23.000 0.500 17.00 18.00 17.000 0.500 16.50 * 588.00
24 x 16 24.00 23.000 0.500 17.00 16.00 15.000 0.500 16.00 * 578.00
24 x 14 24.00 23.000 0.500 17.00 14.00 13.000 0.500 16.00 * 565.00
24 x 12 24.00 23.000 0.500 17.00 12.75 11.750 0.500 15.62 * 558.00
24 x 10 24.00 23.000 0.500 17.00 10.75 9.750 0.500 15.12 * 550.00
30 x 24 30.00 29.000 0.500 22.00 24.00 23.000 0.500 21.00 * 994.00
30 x 20 30.00 29.000 0.500 22.00 20.00 19.000 0.500 20.00 * 945.00
30 x 18 30.00 29.000 0.500 22.00 18.00 17.000 0.500 19.50 * 920.00
30 x 16 30.00 29.000 0.500 22.00 16.00 15.000 0.500 19.00 * 900.00
36 x 30 36.00 35.000 0.500 26.50 30.00 29.000 0.500 25.00 * 1510.00
36 x 24 36.00 35.000 0.500 26.50 24.00 23.000 0.500 24.00 * 1415.00
36 x 20 36.00 35.000 0.500 26.50 20.00 19.000 0.500 23.00 * 1345.00
36 x 18 36.00 35.000 0.500 26.50 18.00 17.000 0.500 22.50 * 1321.00
42 x 36 42.00 41.000 0.500 30.00 36.00 35.000 0.500 28.00 * 1709.00
42 x 30 42.00 41.000 0.500 30.00 30.00 29.000 0.500 28.00 * 1629.00
42 x 24 42.00 41.000 0.500 30.00 24.00 23.000 0.500 26.00 * 1550.00
42 x 20 42.00 41.000 0.500 30.00 20.00 19.000 0.500 26.00 * 1500.00
48 x 42 48.00 47.000 0.500 35.00 42.00 41.000 0.500 32.00 * 2207.00
48 x 36 48.00 47.000 0.500 35.00 36.00 35.000 0.500 31.00 * 2127.00
48 x 30 48.00 47.000 0.500 35.00 30.00 29.000 0.500 30.00 * 2048.00
48 x 24 48.00 47.000 0.500 35.00 24.00 23.000 0.500 29.00 * 1980.00
55

reducing tees
SCHEDULE 40 NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FOR DIMENSION SPECIFICATIONS

1/2" THROUGH 10" REFER TO SCHEDULE STD
12 x 10 12.75 11.938 0.406 10.00 10.75 10.020 0.365 9.50 40 153.75
12 x 8 12.75 11.938 0.406 10.00 8.62 7.976 0.322 9.00 40 150.00
FITTINGS
12 x 6 12.75 11.938 0.406 10.00 6.62 6.060 0.280 8.62 40 147.50

12 x 5 12.75 11.938 0.406 10.00 5.56 5.044 0.258 8.50 40 146.25
❖ 12 x 4 12.75 11.938 0.406 10.00 4.50 4.026 0.237 8.50 40 140.00
14 x 12 14.00 13.124 0.438 11.00 12.75 11.938 0.406 10.62 40 188.75
14 x 10 14.00 13.124 0.438 11.00 10.75 10.020 0.365 10.12 40 185.00
14 x 8 14.00 13.124 0.438 11.00 8.62 7.976 0.322 9.75 40 182.50
14 x 6 14.00 13.124 0.438 11.00 6.62 6.060 0.280 9.38 40 181.25
16 x 14 16.00 15.000 0.500 12.00 14.00 13.124 0.438 12.00 40 276.25
16 x 12 16.00 15.000 0.500 12.00 12.75 11.938 0.406 11.62 40 266.25
16 x 10 16.00 15.000 0.500 12.00 10.75 10.020 0.365 11.12 40 246.25
16 x 8 16.00 15.000 0.500 12.00 8.62 7.976 0.322 10.75 40 237.50
16 x 6 16.00 15.000 0.500 12.00 6.62 6.060 0.280 10.38 40 225.00
18 x 16 18.00 16.876 0.562 13.50 16.00 15.000 0.500 13.00 40 327.50
18 x 14 18.00 16.876 0.562 13.50 14.00 13.124 0.438 13.00 40 310.00
18 x 12 18.00 16.876 0.562 13.50 12.75 11.938 0.406 12.62 40 301.25
18 x 10 18.00 16.876 0.562 13.50 10.75 10.020 0.365 12.12 40 286.25
18 x 8 18.00 16.876 0.562 13.50 8.62 7.976 0.322 11.75 40 270.00
20 x 18 20.00 18.812 0.594 15.00 18.00 16.876 0.562 14.50 40 440.00
20 x 16 20.00 18.812 0.594 15.00 16.00 15.000 0.500 14.00 40 423.75
20 x 14 20.00 18.812 0.594 15.00 14.00 13.124 0.438 14.00 40 408.75
20 x 12 20.00 18.812 0.594 15.00 12.75 11.938 0.406 13.62 40 393.75
20 x 10 20.00 18.812 0.594 15.00 10.75 10.020 0.365 13.12 40 381.25
20 x 8 20.00 18.812 0.594 15.00 8.62 7.976 0.322 12.75 40 366.25
24 x 20 24.00 22.624 0.688 17.00 20.00 18.812 0.594 17.00 40 625.00
24 x 18 24.00 22.624 0.688 17.00 18.00 16.876 0.562 16.50 40 608.75
24 x 16 24.00 22.624 0.688 17.00 16.00 15.000 0.500 16.00 40 593.75
24 x 14 24.00 22.624 0.688 17.00 14.00 13.124 0.438 16.00 40 581.25
24 x 12 24.00 22.624 0.688 17.00 12.75 11.938 0.406 15.62 40 562.50
24 x 10 24.00 22.624 0.688 17.00 10.75 10.020 0.365 15.12 40 558.75
56

TEL: 708/594-1700
FAX: 708/458-0106
NOTES SCHEDULE 80
or estimated.
❖ In accordance with B16.9-2007. Special Fittings
paragraph 4.4.2.

Number Pounds

1/2" THROUGH 8" REFER TO SCHEDULE XS
10 x 8 10.75 9.562 0.594 8.50 8.62 7.620 0.500 8.00 80 151.38
10 x 6 10.75 9.562 0.594 8.50 6.62 5.756 0.432 7.62 80 150.33
FITTINGS
10 x 5 10.75 9.562 0.594 8.50 5.56 4.810 0.375 7.50 80 144.38
10 x 4 10.75 9.562 0.594 8.50 4.50 3.826 0.337 7.25 80 143.50
❖ 10 x 3 10.75 9.562 0.594 8.50 3.50 2.900 0.300 7.25 80 142.00
12 x 10 12.75 11.374 0.688 10.00 10.75 9.562 0.594 9.50 80 215.25
12 x 8 12.75 11.374 0.688 10.00 8.62 7.620 0.500 9.00 80 210.00
12 x 6 12.75 11.374 0.688 10.00 6.62 5.756 0.432 8.62 80 206.50
12 x 5 12.75 11.374 0.688 10.00 5.56 4.810 0.375 8.50 80 204.75
❖ 12 x 4 12.75 11.374 0.688 10.00 4.50 3.826 0.337 8.50 80 196.00
14 x 12 14.00 12.500 0.750 11.00 12.75 11.374 0.688 10.62 80 264.25
14 x 10 14.00 12.500 0.750 11.00 10.75 9.562 0.594 10.12 80 259.00
14 x 8 14.00 12.500 0.750 11.00 8.62 7.620 0.500 9.75 80 255.50
14 x 6 14.00 12.500 0.750 11.00 6.62 5.756 0.432 9.38 80 253.75
16 x 14 16.00 14.312 0.844 12.00 14.00 12.500 0.750 12.00 80 386.75
16 x 12 16.00 14.312 0.844 12.00 12.75 11.374 0.688 11.62 80 372.75
16 x 10 16.00 14.312 0.844 12.00 10.75 9.562 0.594 11.12 80 344.75
16 x 8 16.00 14.312 0.844 12.00 8.62 7.620 0.500 10.75 80 332.50
16 x 6 16.00 14.312 0.844 12.00 6.62 5.756 0.432 10.38 80 315.00
18 x 16 18.00 16.124 0.938 13.50 16.00 14.312 0.844 13.00 80 458.50
18 x 14 18.00 16.124 0.938 13.50 14.00 12.500 0.750 13.00 80 434.00
18 x 12 18.00 16.124 0.938 13.50 12.75 11.374 0.688 12.62 80 421.75
18 x 10 18.00 16.124 0.938 13.50 10.75 9.562 0.594 12.12 80 400.75
18 x 8 18.00 16.124 0.938 13.50 8.62 7.620 0.500 11.75 80 378.00
20 x 18 20.00 17.938 1.031 15.00 18.00 16.124 0.938 14.50 80 616.00
20 x 16 20.00 17.938 1.031 15.00 16.00 14.312 0.844 14.00 80 593.25
20 x 14 20.00 17.938 1.031 15.00 14.00 12.500 0.750 14.00 80 572.25
20 x 12 20.00 17.938 1.031 15.00 12.75 11.374 0.688 13.62 80 551.25
20 x 10 20.00 17.938 1.031 15.00 10.75 9.562 0.594 13.12 80 533.75
20 x 8 20.00 17.938 1.031 15.00 8.62 7.620 0.500 12.75 80 512.75
24 x 20 24.00 21.562 1.219 17.00 20.00 17.938 1.031 17.00 80 875.00
24 x 18 24.00 21.562 1.219 17.00 18.00 16.124 0.938 16.50 80 852.25
24 x 16 24.00 21.562 1.219 17.00 16.00 14.312 0.844 16.00 80 831.25
24 x 14 24.00 21.562 1.219 17.00 14.00 12.500 0.750 16.00 80 813.75
24 x 12 24.00 21.562 1.219 17.00 12.75 11.374 0.688 15.62 80 787.50
24 x 10 24.00 21.562 1.219 17.00 10.75 9.562 0.594 15.12 80 782.25
57

reducing tees
SCHEDULE 160 NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
3/4 x 1/2 1.05 0.612 0.219 1.12 0.84 0.464 0.188 1.12 160 0.66
1 x 3/4 1.32 0.820 0.250 1.50 1.05 0.612 0.219 1.50 160 1.37
1 x 1/2 1.32 0.820 0.250 1.50 0.84 0.464 0.188 1.50 160 1.29
1 1/4 x 1 1.66 1.160 0.250 1.88 1.32 0.820 0.250 1.88 160 2.24
FITTINGS
1 1/4 x 3/4 1.66 1.160 0.250 1.88 1.05 0.612 0.219 1.88 160 2.24
1 1/4 x 1/2 1.66 1.160 0.250 1.88 0.84 0.464 0.188 1.88 160 2.24
1 1/2 x 1 1/4 1.90 1.338 0.281 2.25 1.66 1.160 0.250 2.25 160 3.36
1 1/2 x 1 1.90 1.338 0.281 2.25 1.32 0.820 0.250 2.25 160 3.22
1 1/2 x 3/4 1.90 1.338 0.281 2.25 1.05 0.612 0.219 2.25 160 3.08
1 1/2 x 1/2 1.90 1.338 0.281 2.25 0.84 0.464 0.188 2.25 160 3.08
2 x 1 1/2 2.38 1.692 0.344 2.50 1.90 1.338 0.281 2.38 160 5.32
2 x 1 1/4 2.38 1.692 0.344 2.50 1.66 1.160 0.250 2.25 160 5.18
2x1 2.38 1.692 0.344 2.50 1.32 0.820 0.250 2.00 160 4.90
2 x 3/4 2.38 1.692 0.344 2.50 1.05 0.612 0.219 1.75 160 4.90
2 1/2 x 2 2.88 2.130 0.375 3.00 2.38 1.692 0.344 2.75 160 8.82
2 1/2 x 1 1/2 2.88 2.130 0.375 3.00 1.90 1.338 0.281 2.62 160 8.68
2 1/2 x 1 1/4 2.88 2.130 0.375 3.00 1.66 1.160 0.250 2.50 160 8.40
2 1/2 x 1 2.88 2.130 0.375 3.00 1.32 0.820 0.250 2.25 160 8.12
3 x 2 1/2 3.50 2.624 0.438 3.38 2.88 2.130 0.375 3.25 160 12.32
3x2 3.50 2.624 0.438 3.38 2.38 1.692 0.344 3.00 160 12.04
3 x 1 1/2 3.50 2.624 0.438 3.38 1.90 1.338 0.281 2.88 160 11.34
3 x 1 1/4 3.50 2.624 0.438 3.38 1.66 1.160 0.250 2.75 160 11.20
❖3x1 3.50 2.624 0.438 3.38 1.32 0.820 0.250 2.62 160 11.20
4x3 4.50 3.438 0.531 4.12 3.50 2.624 0.438 3.88 160 21.56
4 x 2 1/2 4.50 3.438 0.531 4.12 2.88 2.130 0.375 3.75 160 21.14
4x2 4.50 3.438 0.531 4.12 2.38 1.692 0.344 3.50 160 21.14
4 x 1 1/2 4.50 3.438 0.531 4.12 1.90 1.338 0.281 3.38 160 21.00
5x4 5.56 4.310 0.625 4.88 4.50 3.438 0.531 4.62 160 35.56
5x3 5.56 4.310 0.625 4.88 3.50 2.624 0.438 4.38 160 33.88
5 x 2 1/2 5.56 4.310 0.625 4.88 2.88 2.130 0.375 4.25 160 33.46
5x2 5.56 4.310 0.625 4.88 2.38 1.692 0.344 4.12 160 33.04
6x5 6.62 5.182 0.719 5.62 5.56 4.310 0.625 5.38 160 55.30
6x4 6.62 5.182 0.719 5.62 4.50 3.438 0.531 5.12 160 55.02
6x3 6.62 5.182 0.719 5.62 3.50 2.624 0.438 4.88 160 54.04
6 x 2 1/2 6.62 5.182 0.719 5.62 2.88 2.130 0.375 4.75 160 53.48
❖6x2 6.62 5.182 0.719 5.62 2.38 1.692 0.344 4.75 160 52.36
58

TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
8x6 8.62 6.808 0.906 7.00 6.62 5.182 0.719 6.62 160 98.28
8x5 8.62 6.808 0.906 7.00 5.56 4.310 0.625 6.38 160 97.16
8x4 8.62 6.808 0.906 7.00 4.50 3.438 0.531 6.12 160 96.88
❖8x3 8.62 6.808 0.906 7.00 3.50 2.624 0.438 6.00 160 95.62
10 x 8 10.75 8.500 1.125 8.50 8.62 6.808 0.906 8.00 160 149.80
10 x 6 10.75 8.500 1.125 8.50 6.62 5.182 0.719 7.62 160 145.60
10 x 5 10.75 8.500 1.125 8.50 5.56 4.310 0.625 7.50 160 144.20
10 x 4 10.75 8.500 1.125 8.50 4.50 3.438 0.531 7.25 160 141.40
❖ 10 x 3 10.75 8.500 1.125 8.50 3.50 2.624 0.438 7.25 160 140.00
12 x 10 12.75 10.126 1.312 10.00 10.75 8.500 1.125 9.50 160 231.00
12 x 8 12.75 10.126 1.312 10.00 8.62 6.808 0.906 9.00 160 218.40
12 x 6 12.75 10.126 1.312 10.00 6.62 5.182 0.719 8.62 160 211.40
12 x 5 12.75 10.126 1.312 10.00 5.56 4.310 0.625 8.50 160 208.60
❖ 12 x 4 12.75 10.126 1.312 10.00 4.50 3.438 0.531 8.50 160 207.20
FITTINGS
14 x 12 14.00 11.188 1.406 11.00 12.75 10.126 1.312 10.62 160 294.00
14 x 10 14.00 11.188 1.406 11.00 10.75 8.500 1.125 10.12 160 284.20
14 x 8 14.00 11.188 1.406 11.00 8.62 6.808 0.906 9.75 160 280.00
14 x 6 14.00 11.188 1.406 11.00 6.62 5.182 0.719 9.38 160 274.40
16 x 14 16.00 12.812 1.594 12.00 14.00 11.188 1.406 12.00 160 375.20
16 x 12 16.00 12.812 1.594 12.00 12.75 10.126 1.312 11.62 160 365.40
16 x 10 16.00 12.812 1.594 12.00 10.75 8.500 1.125 11.12 160 350.00
16 x 8 16.00 12.812 1.594 12.00 8.62 6.808 0.906 10.75 160 336.00
16 x 6 16.00 12.812 1.594 12.00 6.62 5.182 0.719 10.38 160 329.00
18 x 16 18.00 14.438 1.781 13.50 16.00 12.812 1.594 13.00 160 487.20
18 x 14 18.00 14.438 1.781 13.50 14.00 11.188 1.406 13.00 160 469.00
18 x 12 18.00 14.438 1.781 13.50 12.75 10.126 1.312 12.62 160 459.20
18 x 10 18.00 14.438 1.781 13.50 10.75 8.500 1.125 12.12 160 431.20
18 x 8 18.00 14.438 1.781 13.50 8.62 6.808 0.906 11.75 160 420.00
20 x 18 20.00 16.062 1.969 15.00 18.00 14.438 1.781 14.50 160 623.00
20 x 16 20.00 16.062 1.969 15.00 16.00 12.812 1.594 14.00 160 597.80
20 x 14 20.00 16.062 1.969 15.00 14.00 11.188 1.406 14.00 160 576.80
20 x 12 20.00 16.062 1.969 15.00 12.75 10.126 1.312 13.62 160 555.80
20 x 10 20.00 16.062 1.969 15.00 10.75 8.500 1.125 13.12 160 537.60
20 x 8 20.00 16.062 1.969 15.00 8.62 6.808 0.906 12.75 160 525.00
24 x 20 24.00 19.312 2.344 17.00 20.00 16.062 1.969 17.00 160 854.00
24 x 18 24.00 19.312 2.344 17.00 18.00 14.438 1.781 16.50 160 823.20
24 x 16 24.00 19.312 2.344 17.00 16.00 12.812 1.594 16.00 160 809.20
24 x 14 24.00 19.312 2.344 17.00 14.00 11.188 1.406 16.00 160 791.00
24 x 12 24.00 19.312 2.344 17.00 12.75 10.126 1.312 15.62 160 781.20
24 x 10 24.00 19.312 2.344 17.00 10.75 8.500 1.125 15.12 160 770.00
59

reducing tees
SCHEDULE XXS NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
3/4 x 1/2 1.05 0.434 0.308 1.12 0.84 0.252 0.294 1.12 * 0.74
1 x 3/4 1.32 0.604 0.358 1.50 1.05 0.434 0.308 1.50 * 1.54
1 x 1/2 1.32 0.604 0.358 1.50 0.84 0.252 0.294 1.50 * 1.45
1 1/4 x 1 1.66 0.896 0.382 1.88 1.32 0.604 0.358 1.88 * 2.52
FITTINGS
1 1/4 x 3/4 1.66 0.896 0.382 1.88 1.05 0.434 0.308 1.88 * 2.52
1 1/4 x 1/2 1.66 0.896 0.382 1.88 0.84 0.252 0.294 1.88 * 2.52
1 1/2 x 1 1/4 1.90 1.100 0.400 2.25 1.66 0.896 0.382 2.25 * 3.78
1 1/2 x 1 1.90 1.100 0.400 2.25 1.32 0.604 0.358 2.25 * 3.62
1 1/2 x 3/4 1.90 1.100 0.400 2.25 1.05 0.434 0.308 2.25 * 3.47
1 1/2 x 1/2 1.90 1.100 0.400 2.25 0.84 0.252 0.294 2.25 * 3.47
2 x 1 1/2 2.38 1.508 0.436 2.50 1.90 1.100 0.400 2.38 * 5.99
2 x 1 1/4 2.38 1.508 0.436 2.50 1.66 0.896 0.382 2.25 * 5.83
2x1 2.38 1.508 0.436 2.50 1.32 0.604 0.358 2.00 * 5.51
2 x 3/4 2.38 1.508 0.436 2.50 1.05 0.434 0.308 1.75 * 5.51
2 1/2 x 2 2.88 1.776 0.552 3.00 2.38 1.508 0.436 2.75 * 9.92
2 1/2 x 1 1/2 2.88 1.776 0.552 3.00 1.90 1.100 0.400 2.62 * 9.77
2 1/2 x 1 1/4 2.88 1.776 0.552 3.00 1.66 0.896 0.382 2.50 * 9.45
2 1/2 x 1 2.88 1.776 0.552 3.00 1.32 0.604 0.358 2.25 * 9.14
3 x 2 1/2 3.50 2.300 0.600 3.38 2.88 1.776 0.552 3.25 * 13.86
3x2 3.50 2.300 0.600 3.38 2.38 1.508 0.436 3.00 * 13.55
3 x 1 1/2 3.50 2.300 0.600 3.38 1.90 1.100 0.400 2.88 * 12.76
3 x 1 1/4 3.50 2.300 0.600 3.38 1.66 0.896 0.382 2.75 * 12.60
❖3x1 3.50 2.300 0.600 3.38 1.32 0.604 0.358 2.62 * 12.60
4x3 4.50 3.152 0.674 4.12 3.50 2.300 0.600 3.88 * 24.26
4 x 2 1/2 4.50 3.152 0.674 4.12 2.88 1.776 0.552 3.75 * 23.78
4x2 4.50 3.152 0.674 4.12 2.38 1.508 0.436 3.50 * 23.78
4 x 1 1/2 4.50 3.152 0.674 4.12 1.90 1.100 0.400 3.38 * 23.63
5x4 5.56 4.060 0.750 4.88 4.50 3.152 0.674 4.62 * 40.01
5x3 5.56 4.060 0.750 4.88 3.50 2.300 0.600 4.38 * 38.12
5 x 2 1/2 5.56 4.060 0.750 4.88 2.88 1.776 0.552 4.25 * 37.64
5x2 5.56 4.060 0.750 4.88 2.38 1.508 0.436 4.12 * 37.17
60

TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
6x5 6.62 4.892 0.864 5.62 5.56 4.060 0.750 5.38 * 62.21
6x4 6.62 4.892 0.864 5.62 4.50 3.152 0.674 5.12 * 61.90
6x3 6.62 4.892 0.864 5.62 3.50 2.300 0.600 4.88 * 60.80
6 x 2 1/2 6.62 4.892 0.864 5.62 2.88 1.776 0.552 4.75 * 60.17
❖6x2 6.62 4.892 0.864 5.62 2.38 1.508 0.436 4.75 * 58.91
8x6 8.62 6.870 0.875 7.00 6.62 4.892 0.864 6.62 * 110.57
8x5 8.62 6.870 0.875 7.00 5.56 4.060 0.750 6.38 * 109.31
8x4 8.62 6.870 0.875 7.00 4.50 3.152 0.674 6.12 * 108.99
❖8x3 8.62 6.870 0.875 7.00 3.50 2.300 0.600 6.00 * 107.57
10 x 8 10.75 8.750 1.000 8.50 8.62 6.870 0.875 8.00 * 168.53
10 x 6 10.75 8.750 1.000 8.50 6.62 4.892 0.864 7.62 * 163.80
10 x 5 10.75 8.750 1.000 8.50 5.56 4.060 0.750 7.50 * 162.23
10 x 4 10.75 8.750 1.000 8.50 4.50 3.152 0.674 7.25 * 159.08
❖ 10 x 3 10.75 8.750 1.000 8.50 3.50 2.300 0.600 7.25 * 158.00
FITTINGS
12 x 10 12.75 10.750 1.000 10.00 10.75 8.750 1.000 9.50 * 259.88
12 x 8 12.75 10.750 1.000 10.00 8.62 6.870 0.875 9.00 * 245.70
12 x 6 12.75 10.750 1.000 10.00 6.62 4.892 0.864 8.62 * 237.83
12 x 5 12.75 10.750 1.000 10.00 5.56 4.060 0.750 8.50 * 234.68
❖ 12 x 4 12.75 10.750 1.000 10.00 4.50 3.152 0.674 8.50 * 233.10
61

concentric and eccentric reducers
SCHEDULE STD NOTES
or estimated.
paragraph 4.4.2.

Pipe Outside Inside Wall Outside Inside Wall Length Pipe Approx.
Size Diameter Diameter Thickness Diameter Diameter Thickness Schedule Weight in
Number Pounds
O.D. I.D. T O.D. I.D. T L
FITTINGS
3/4 x 1/2 1.05 0.824 0.113 0.84 0.622 0.109 1.50 40 0.21
1 x 3/4 1.32 1.054 0.133 1.05 0.824 0.113 2.00 40 0.36
1 x 1/2 1.32 1.054 0.133 0.84 0.622 0.109 2.00 40 0.36
1 1/4 x 1 1.66 1.380 0.140 1.32 1.054 0.133 2.00 40 0.48
1 1/4 x 3/4 1.66 1.380 0.140 1.05 0.824 0.113 2.00 40 0.42
1 1/4 x 1/2 1.66 1.380 0.140 0.84 0.622 0.109 2.00 40 0.42
1 1/2 x 1 1/4 1.90 1.610 0.145 1.66 1.380 0.140 2.50 40 0.65
1 1/2 x 1 1.90 1.610 0.145 1.32 1.054 0.133 2.50 40 0.57
1 1/2 x 3/4 1.90 1.610 0.145 1.05 0.824 0.113 2.50 40 0.56
1 1/2 x 1/2 1.90 1.610 0.145 0.84 0.622 0.109 2.50 40 0.56
2 x 1 1/2 2.38 2.072 0.154 1.90 1.610 0.145 3.00 40 0.94
2 x 1 1/4 2.38 2.072 0.154 1.66 1.380 0.140 3.00 40 0.88
2x1 2.38 2.072 0.154 1.32 1.054 0.133 3.00 40 0.81
2 x 3/4 2.38 2.072 0.154 1.05 0.824 0.113 3.00 40 0.74
2 1/2 x 2 2.88 2.474 0.203 2.38 2.072 0.154 3.50 40 1.60
2 1/2 x 1 1/2 2.88 2.474 0.203 1.90 1.610 0.145 3.50 40 1.50
2 1/2 x 1 1/4 2.88 2.474 0.203 1.66 1.380 0.140 3.50 40 1.40
2 1/2 x 1 2.88 2.474 0.203 1.32 1.054 0.133 3.50 40 1.30
3 x 2 1/2 3.50 3.068 0.216 2.88 2.474 0.203 3.50 40 2.20
3x2 3.50 3.068 0.216 2.38 2.072 0.154 3.50 40 2.00
3 x 1 1/2 3.50 3.068 0.216 1.90 1.610 0.145 3.50 40 1.90
3 x 1 1/4 3.50 3.068 0.216 1.66 1.380 0.140 3.50 40 1.80
❖3x1 3.50 3.068 0.216 1.32 1.054 0.133 3.50 40 1.70
3 1/2 x 3 4.00 3.548 0.226 3.50 3.068 0.216 4.00 40 2.80
3 1/2 x 2 1/2 4.00 3.548 0.226 2.88 2.474 0.203 4.00 40 2.70
3 1/2 x 2 4.00 3.548 0.226 2.38 2.072 0.154 4.00 40 2.60
3 1/2 x 1 1/2 4.00 3.548 0.226 1.90 1.610 0.145 4.00 40 2.60
3 1/2 x 1 1/4 4.00 3.548 0.226 1.66 1.380 0.140 4.00 40 2.50
4 x 3 1/2 4.50 4.026 0.237 4.00 3.548 0.226 4.00 40 3.50
4x3 4.50 4.026 0.237 3.50 3.068 0.216 4.00 40 3.30
4 x 2 1/2 4.50 4.026 0.237 2.88 2.474 0.203 4.00 40 3.20
4x2 4.50 4.026 0.237 2.38 2.072 0.154 4.00 40 3.10
62 4 x 1 1/2 4.50 4.026 0.237 1.90 1.610 0.145 4.00 40 3.00
TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com concentric and eccentric reducers

Number Pounds
❖ 4 x 1 1/4 4.50 4.026 0.237 1.66 1.380 0.140 4.00 40 3.00
❖ 4x1 4.50 4.026 0.237 1.32 1.054 0.133 4.00 40 2.80
5x4 5.56 5.044 0.258 4.50 4.026 0.237 5.00 40 5.50
5 x 3 1/2 5.56 5.044 0.258 4.00 3.548 0.226 5.00 40 5.30
5x3 5.56 5.044 0.258 3.50 3.068 0.216 5.00 40 5.10
5 x 2 1/2 5.56 5.044 0.258 2.88 2.474 0.203 5.00 40 4.80
5x2 5.56 5.044 0.258 2.38 2.072 0.154 5.00 40 4.70
6x5 6.62 6.060 0.280 5.56 5.044 0.258 5.50 40 7.60
6x4 6.62 6.060 0.280 4.50 4.026 0.237 5.50 40 7.40
6 x 3 1/2 6.62 6.060 0.280 4.00 3.548 0.226 5.50 40 7.10
6x3 6.62 6.060 0.280 3.50 3.068 0.216 5.50 40 6.90
6 x 2 1/2 6.62 6.060 0.280 2.88 2.474 0.203 5.50 40 6.60
FITTINGS
❖ 6x2 6.62 6.060 0.280 2.38 2.072 0.154 5.50 40 6.50
8x6 8.62 7.976 0.322 6.62 6.060 0.280 6.00 40 12.30
8x5 8.62 7.976 0.322 5.56 5.044 0.258 6.00 40 11.50
8x4 8.62 7.976 0.322 4.50 4.026 0.237 6.00 40 10.80
8 x 3 1/2 8.62 7.976 0.322 4.00 3.548 0.226 6.00 40 10.60
❖ 8x3 8.62 7.976 0.322 3.50 3.068 0.216 6.00 40 9.80
10 x 8 10.75 10.020 0.365 8.62 7.976 0.322 7.00 40 22.10
10 x 6 10.75 10.020 0.365 6.62 6.060 0.280 7.00 40 20.70
10 x 5 10.75 10.020 0.365 5.56 5.044 0.258 7.00 40 19.50
10 x 4 10.75 10.020 0.365 4.50 4.026 0.237 7.00 40 18.40
12 x 10 12.75 12.000 0.375 10.75 10.020 0.365 8.00 * 32.40
12 x 8 12.75 12.000 0.375 8.62 7.976 0.322 8.00 * 30.50
12 x 6 12.75 12.000 0.375 6.62 6.060 0.280 8.00 * 29.50
12 x 5 12.75 12.000 0.375 5.56 5.044 0.258 8.00 * 27.80
❖ 12 x 4 12.75 12.000 0.375 4.50 4.026 0.237 8.00 * 26.20
14 x 12 14.00 13.250 0.375 12.75 12.000 0.375 13.00 * 63.10
14 x 10 14.00 13.250 0.375 10.75 10.020 0.365 13.00 * 61.40
14 x 8 14.00 13.250 0.375 8.62 7.976 0.322 13.00 * 60.00
14 x 6 14.00 13.250 0.375 6.62 6.060 0.280 13.00 * 59.20
16 x 14 16.00 15.250 0.375 14.00 13.250 0.375 14.00 * 75.40
16 x 12 16.00 15.250 0.375 12.75 12.000 0.375 14.00 * 72.70
16 x 10 16.00 15.250 0.375 10.75 10.020 0.365 14.00 * 71.10
16 x 8 16.00 15.250 0.375 8.62 7.976 0.322 14.00 * 69.40
❖ 16 x 6 16.00 15.250 0.375 6.62 6.060 0.280 14.00 * 67.40
18 x 16 18.00 17.250 0.375 16.00 15.250 0.375 15.00 * 87.30
18 x 14 18.00 17.250 0.375 14.00 13.250 0.375 15.00 * 86.00
18 x 12 18.00 17.250 0.375 12.75 12.000 0.375 15.00 * 84.80
18 x 10 18.00 17.250 0.375 10.75 10.020 0.365 15.00 * 83.70
❖ 18 x 8 18.00 17.250 0.375 8.62 7.976 0.322 15.00 * 81.75
20 x 18 20.00 19.250 0.375 18.00 17.250 0.375 20.00 * 123.00
20 x 16 20.00 19.250 0.375 16.00 15.250 0.375 20.00 * 121.00
20 x 14 20.00 19.250 0.375 14.00 13.250 0.375 20.00 * 119.00 63

SCHEDULE STD NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
20 x 12 20.00 19.250 0.375 12.75 12.000 0.375 20.00 * 118.00

❖ 20 x 10 20.00 19.250 0.375 10.75 10.020 0.365 20.00 * 117.00
24 x 20 24.00 23.250 0.375 20.00 19.250 0.375 20.00 * 156.00
24 x 18 24.00 23.250 0.375 18.00 17.250 0.375 20.00 * 153.00
24 x 16 24.00 23.250 0.375 16.00 15.250 0.375 20.00 * 150.00
❖ 24 x 14 24.00 23.250 0.375 14.00 13.250 0.375 20.00 * 147.00
❖ 24 x 12 24.00 23.250 0.375 12.75 12.000 0.375 20.00 * 144.00
❖ 24 x 10 24.00 23.250 0.375 10.75 10.020 0.365 20.00 * 141.00
30 x 24 30.00 29.250 0.375 24.00 23.250 0.375 24.00 * 315.00
30 x 20 30.00 29.250 0.375 20.00 19.250 0.375 24.00 * 315.00
❖ 30 x 18 30.00 29.250 0.375 18.00 17.250 0.375 24.00 * 315.00
36 x 30 36.00 35.250 0.375 30.00 29.250 0.375 24.00 * 379.00
36 x 24 36.00 35.250 0.375 24.00 23.250 0.375 24.00 * 379.00
❖ 36 x 20 36.00 35.250 0.375 20.00 19.250 0.375 24.00 * 379.00
42 x 36 42.00 41.250 0.375 36.00 35.250 0.375 24.00 * 443.00
42 x 30 42.00 41.250 0.375 30.00 29.250 0.375 24.00 * 443.00
❖ 42 x 24 42.00 41.250 0.375 24.00 23.250 0.375 24.00 * 443.00
48 x 42 48.00 47.250 0.375 42.00 41.250 0.375 28.00 * 525.00
❖ 48 x 36 48.00 47.250 0.375 36.00 35.250 0.375 28.00 * 525.00
❖ 48 x 30 48.00 47.250 0.375 30.00 29.250 0.375 28.00 * 525.00
❖ 48 x 24 48.00 47.250 0.375 24.00 23.250 0.375 28.00 * 525.00
64

TEL: 708/594-1700
FAX: 708/458-0106
NOTES SCHEDULE XS
or estimated.
paragraph 4.4.2.

Number Pounds
3/4 x 1/2 1.05 0.742 0.154 0.84 0.546 0.147 1.50 80 0.25
FITTINGS
1 x 3/4 1.32 0.962 0.179 1.05 0.742 0.154 2.00 80 0.43
1 x 1/2 1.32 0.962 0.179 0.84 0.546 0.147 2.00 80 0.42
1 1/4 x 1 1.66 1.278 0.191 1.32 0.962 0.179 2.00 80 0.57
1 1/4 x 3/4 1.66 1.278 0.191 1.05 0.742 0.154 2.00 80 0.53
1 1/4 x 1/2 1.66 1.278 0.191 0.84 0.546 0.147 2.00 80 0.50
1 1/2 x 1 1/4 1.90 1.500 0.200 1.66 1.278 0.191 2.50 80 0.78
1 1/2 x 1 1.90 1.500 0.200 1.32 0.962 0.179 2.50 80 0.72
1 1/2 x 3/4 1.90 1.500 0.200 1.05 0.742 0.154 2.50 80 0.65
1 1/2 x 1/2 1.90 1.500 0.200 0.84 0.546 0.147 2.50 80 0.65
2 x 1 1/2 2.38 1.944 0.218 1.90 1.500 0.200 3.00 80 1.20
2 x 1 1/4 2.38 1.944 0.218 1.66 1.278 0.191 3.00 80 1.10
2x1 2.38 1.944 0.218 1.32 0.962 0.179 3.00 80 1.00
2 x 3/4 2.38 1.944 0.218 1.05 0.742 0.154 3.00 80 0.94
2 1/2 x 2 2.88 2.328 0.276 2.38 1.944 0.218 3.50 80 2.10
2 1/2 x 1 1/2 2.88 2.328 0.276 1.90 1.500 0.200 3.50 80 1.90
2 1/2 x 1 1/4 2.88 2.328 0.276 1.66 1.278 0.191 3.50 80 1.70
2 1/2 x 1 2.88 2.328 0.276 1.32 0.962 0.179 3.50 80 1.50
3 x 2 1/2 3.50 2.900 0.300 2.88 2.328 0.276 3.50 80 2.80
3x2 3.50 2.900 0.300 2.38 1.944 0.218 3.50 80 2.60
3 x 1 1/2 3.50 2.900 0.300 1.90 1.500 0.200 3.50 80 2.40
3 x 1 1/4 3.50 2.900 0.300 1.66 1.278 0.191 3.50 80 2.30
❖3x1 3.50 2.900 0.300 1.32 0.962 0.179 3.50 80 2.20
3 1/2 x 3 4.00 3.364 0.318 3.50 2.900 0.300 4.00 80 3.70
3 1/2 x 2 1/2 4.00 3.364 0.318 2.88 2.328 0.276 4.00 80 3.50
3 1/2 x 2 4.00 3.364 0.318 2.38 1.944 0.218 4.00 80 3.30
3 1/2 x 1 1/2 4.00 3.364 0.318 1.90 1.500 0.200 4.00 80 3.20
3 1/2 x 1 1/4 4.00 3.364 0.318 1.66 1.278 0.191 4.00 80 3.20
4 x 3 1/2 4.50 3.826 0.337 4.00 3.364 0.318 4.00 80 4.90
4x3 4.50 3.826 0.337 3.50 2.900 0.300 4.00 80 4.70
4 x 2 1/2 4.50 3.826 0.337 2.88 2.328 0.276 4.00 80 4.60
4x2 4.50 3.826 0.337 2.38 1.944 0.218 4.00 80 4.30
4 x 1 1/2 4.50 3.826 0.337 1.90 1.500 0.200 4.00 80 4.20 65

SCHEDULE XS NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
❖ 4 x 1 1/4 4.50 3.826 0.337 1.66 1.278 0.191 4.00 80 4.10

❖ 4x1 4.50 3.826 0.337 1.32 0.962 0.179 4.00 80 4.00
5x4 5.56 4.810 0.375 4.50 3.826 0.337 5.00 80 7.50
5 x 3 1/2 5.56 4.810 0.375 4.00 3.364 0.318 5.00 80 6.90
5x3 5.56 4.810 0.375 3.50 2.900 0.300 5.00 80 6.30
5 x 2 1/2 5.56 4.810 0.375 2.88 2.328 0.276 5.00 80 6.10
5x2 5.56 4.810 0.375 2.38 1.944 0.218 5.00 80 6.00
6x5 6.62 5.756 0.432 5.56 4.810 0.375 5.50 80 11.50
6x4 6.62 5.756 0.432 4.50 3.826 0.337 5.50 80 10.70
6 x 3 1/2 6.62 5.756 0.432 4.00 3.364 0.318 5.50 80 10.00
6x3 6.62 5.756 0.432 3.50 2.900 0.300 5.50 80 9.70
6 x 2 1/2 6.62 5.756 0.432 2.88 2.328 0.276 5.50 80 9.10
❖ 6x2 6.62 5.756 0.432 2.38 1.944 0.218 5.50 80 8.60
8x6 8.62 7.620 0.500 6.62 5.756 0.432 6.00 80 18.80
8x5 8.62 7.620 0.500 5.56 4.810 0.375 6.00 80 17.60
8x4 8.62 7.620 0.500 4.50 3.826 0.337 6.00 80 17.00
8 x 3 1/2 8.62 7.620 0.500 4.00 3.364 0.318 6.00 80 15.90
❖ 8x3 8.62 7.620 0.500 3.50 2.900 0.300 6.00 80 15.00
10 x 8 10.75 9.750 0.500 8.62 7.620 0.500 7.00 * 29.40
10 x 6 10.75 9.750 0.500 6.62 5.756 0.432 7.00 * 28.30
10 x 5 10.75 9.750 0.500 5.56 4.810 0.375 7.00 * 26.90
10 x 4 10.75 9.750 0.500 4.50 3.826 0.337 7.00 * 24.20
12 x 10 12.75 11.750 0.500 10.75 9.750 0.500 8.00 * 41.50
12 x 8 12.75 11.750 0.500 8.62 7.620 0.500 8.00 * 38.60
12 x 6 12.75 11.750 0.500 6.62 5.756 0.432 8.00 * 37.40
12 x 5 12.75 11.750 0.500 5.56 4.810 0.375 8.00 * 36.30
❖ 12 x 4 12.75 11.750 0.500 4.50 3.826 0.337 8.00 * 34.70
14 x 12 14.00 13.000 0.500 12.75 11.750 0.500 13.00 * 81.00
14 x 10 14.00 13.000 0.500 10.75 9.750 0.500 13.00 * 76.70
14 x 8 14.00 13.000 0.500 8.62 7.620 0.500 13.00 * 74.60
14 x 6 14.00 13.000 0.500 6.62 5.756 0.432 13.00 * 72.30
16 x 14 16.00 15.000 0.500 14.00 13.000 0.500 14.00 * 98.00
66

TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
16 x 12 16.00 15.000 0.500 12.75 11.750 0.500 14.00 * 95.80
16 x 10 16.00 15.000 0.500 10.75 9.750 0.500 14.00 * 93.30
16 x 8 16.00 15.000 0.500 8.62 7.620 0.500 14.00 * 91.10
❖ 16 x 6 16.00 15.000 0.500 6.62 5.756 0.432 14.00 * 89.80
18 x 16 18.00 17.000 0.500 16.00 15.000 0.500 15.00 * 118.00
18 x 14 18.00 17.000 0.500 14.00 13.000 0.500 15.00 * 117.00
18 x 12 18.00 17.000 0.500 12.75 11.750 0.500 15.00 * 115.00
18 x 10 18.00 17.000 0.500 10.75 9.750 0.500 15.00 * 113.00
❖ 18 x 8 18.00 17.000 0.500 8.62 7.620 0.500 15.00 * 100.00
20 x 18 20.00 19.000 0.500 18.00 17.000 0.500 20.00 * 162.00
20 x 16 20.00 19.000 0.500 16.00 15.000 0.500 20.00 * 159.00
20 x 14 20.00 19.000 0.500 14.00 13.000 0.500 20.00 * 157.00
FITTINGS
20 x 12 20.00 19.000 0.500 12.75 11.750 0.500 20.00 * 155.00
❖ 20 x 10 20.00 19.000 0.500 10.75 9.750 0.500 20.00 * 152.00
24 x 20 24.00 23.000 0.500 20.00 19.000 0.500 20.00 * 201.00
24 x 18 24.00 23.000 0.500 18.00 17.000 0.500 20.00 * 197.00
24 x 16 24.00 23.000 0.500 16.00 15.000 0.500 20.00 * 194.00
❖ 24 x 14 24.00 23.000 0.500 14.00 13.000 0.500 20.00 * 190.00
❖ 24 x 12 24.00 23.000 0.500 12.75 11.750 0.500 20.00 * 188.00
❖ 24 x 10 24.00 23.000 0.500 10.75 9.750 0.500 20.00 * 186.00
30 x 24 30.00 29.000 0.500 24.00 23.000 0.500 24.00 * 315.00
30 x 20 30.00 29.000 0.500 20.00 19.000 0.500 24.00 * 315.00
❖ 30 x 18 30.00 29.000 0.500 18.00 17.000 0.500 24.00 * 315.00
36 x 30 36.00 35.000 0.500 30.00 29.000 0.500 24.00 * 379.00
36 x 24 36.00 35.000 0.500 24.00 23.000 0.500 24.00 * 379.00
❖ 36 x 20 36.00 35.000 0.500 20.00 19.000 0.500 24.00 * 379.00
42 x 36 42.00 41.000 0.500 36.00 35.000 0.500 24.00 * 443.00
42 x 30 42.00 41.000 0.500 30.00 29.000 0.500 24.00 * 443.00
❖ 42 x 24 42.00 41.000 0.500 24.00 23.000 0.500 24.00 * 443.00
48 x 42 48.00 47.000 0.500 42.00 41.000 0.500 28.00 * 525.00
❖ 48 x 36 48.00 47.000 0.500 36.00 35.000 0.500 28.00 * 525.00
❖ 48 x 30 48.00 47.000 0.500 30.00 29.000 0.500 28.00 * 525.00
❖ 48 x 24 48.00 47.000 0.500 24.00 23.000 0.500 28.00 * 525.00
67

SCHEDULE 40 NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS

12 x 10 12.75 11.938 0.406 10.75 10.020 0.365 8.00 40 35.80
12 x 8 12.75 11.938 0.406 8.62 7.976 0.322 8.00 40 35.80
12 x 6 12.75 11.938 0.406 6.62 6.060 0.280 8.00 40 35.80
12 x 5 12.75 11.938 0.406 5.56 5.044 0.258 8.00 40 35.80
❖ 12 x 4 12.75 11.938 0.406 4.50 4.026 0.237 8.00 40 35.80
14 x 12 14.00 13.124 0.438 12.75 11.938 0.406 13.00 40 68.60
14 x 10 14.00 13.124 0.438 10.75 10.020 0.365 13.00 40 68.60
14 x 8 14.00 13.124 0.438 8.62 7.976 0.322 13.00 40 68.60
14 x 6 14.00 13.124 0.438 6.62 6.060 0.280 13.00 40 68.60
16 x 14 16.00 15.000 0.500 14.00 13.124 0.438 14.00 40 96.50
16 x 12 16.00 15.000 0.500 12.75 11.938 0.406 14.00 40 96.50
16 x 10 16.00 15.000 0.500 10.75 10.020 0.365 14.00 40 96.50
16 x 8 16.00 15.000 0.500 8.62 7.976 0.322 14.00 40 96.50
❖ 16 x 6 16.00 15.000 0.500 6.62 6.060 0.280 14.00 40 96.50
18 x 16 18.00 16.876 0.562 16.00 15.000 0.500 15.00 40 131.00
18 x 14 18.00 16.876 0.562 14.00 13.124 0.438 15.00 40 131.00
18 x 12 18.00 16.876 0.562 12.75 11.938 0.406 15.00 40 131.00
18 x 10 18.00 16.876 0.562 10.75 10.020 0.365 15.00 40 131.00
❖ 18 x 8 18.00 16.876 0.562 8.62 7.976 0.322 15.00 40 131.00
20 x 18 20.00 18.812 0.594 18.00 16.876 0.562 20.00 40 205.00
20 x 16 20.00 18.812 0.594 16.00 15.000 0.500 20.00 40 205.00
20 x 14 20.00 18.812 0.594 14.00 13.124 0.438 20.00 40 205.00
20 x 12 20.00 18.812 0.594 12.75 11.938 0.406 20.00 40 205.00
❖ 20 x 10 20.00 18.812 0.594 10.75 10.020 0.365 20.00 40 205.00
❖ 20 x 8 20.00 18.812 0.594 8.62 7.976 0.322 20.00 40 205.00
24 x 20 24.00 22.624 0.688 20.00 18.812 0.594 20.00 40 285.00
24 x 18 24.00 22.624 0.688 18.00 16.876 0.562 20.00 40 285.00
24 x 16 24.00 22.624 0.688 16.00 15.000 0.500 20.00 40 285.00
❖ 24 x 14 24.00 22.624 0.688 14.00 13.124 0.438 20.00 40 285.00
❖ 24 x 12 24.00 22.624 0.688 12.75 11.938 0.406 20.00 40 285.00
68 ❖ 24 x 10 24.00 22.624 0.688 10.75 10.020 0.365 20.00 40 285.00

TEL: 708/594-1700
FAX: 708/458-0106
NOTES SCHEDULE 80
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
10 x 8 10.75 9.562 0.594 8.62 7.620 0.500 7.00 80 37.50
10 x 6 10.75 9.562 0.594 6.62 5.756 0.432 7.00 80 37.50
10 x 5 10.75 9.562 0.594 5.56 4.810 0.375 7.00 80 37.50
10 x 4 10.75 9.562 0.594 4.50 3.826 0.337 7.00 80 37.50
12 x 10 12.75 11.374 0.688 10.75 9.562 0.594 8.00 80 59.00
12 x 8 12.75 11.374 0.688 8.62 7.620 0.500 8.00 80 59.00
12 x 6 12.75 11.374 0.688 6.62 5.756 0.432 8.00 80 59.00
12 x 5 12.75 11.374 0.688 5.56 4.810 0.375 8.00 80 59.00
❖ 12 x 4 12.75 11.374 0.688 4.50 3.826 0.337 8.00 80 59.00
14 x 12 14.00 12.500 0.750 12.75 11.374 0.688 13.00 80 115.00
14 x 10 14.00 12.500 0.750 10.75 9.562 0.594 13.00 80 115.00
14 x 8 14.00 12.500 0.750 8.62 7.620 0.500 13.00 80 115.00
14 x 6 14.00 12.500 0.750 6.62 5.756 0.432 13.00 80 115.00
16 x 14 16.00 14.312 0.844 14.00 12.500 0.750 14.00 80 159.00
16 x 12 16.00 14.312 0.844 12.75 11.374 0.688 14.00 80 159.00
16 x 10 16.00 14.312 0.844 10.75 9.562 0.594 14.00 80 159.00
16 x 8 16.00 14.312 0.844 8.62 7.620 0.500 14.00 80 159.00
❖ 16 x 6 16.00 14.312 0.844 6.62 5.756 0.432 14.00 80 159.00
18 x 16 18.00 16.124 0.938 16.00 14.312 0.844 15.00 80 213.00
18 x 14 18.00 16.124 0.938 14.00 12.500 0.750 15.00 80 213.00
18 x 12 18.00 16.124 0.938 12.75 11.374 0.688 15.00 80 213.00
18 x 10 18.00 16.124 0.938 10.75 9.562 0.594 15.00 80 213.00
❖ 18 x 8 18.00 16.124 0.938 8.62 7.620 0.500 15.00 80 213.00
69

SCHEDULE 80 NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
20 x 18 20.00 17.938 1.031 18.00 16.124 0.938 20.00 80 348.00

20 x 16 20.00 17.938 1.031 16.00 14.312 0.844 20.00 80 348.00
20 x 14 20.00 17.938 1.031 14.00 12.500 0.750 20.00 80 348.00
20 x 12 20.00 17.938 1.031 12.75 11.374 0.688 20.00 80 348.00
❖ 20 x 10 20.00 17.938 1.031 10.75 9.562 0.594 20.00 80 348.00
❖ 20 x 8 20.00 17.938 1.031 8.62 7.620 0.500 20.00 80 348.00
24 x 20 24.00 21.562 1.219 20.00 17.938 1.031 20.00 80 494.00
24 x 18 24.00 21.562 1.219 18.00 16.124 0.938 20.00 80 494.00
24 x 16 24.00 21.562 1.219 16.00 14.312 0.844 20.00 80 494.00
❖ 24 x 14 24.00 21.562 1.219 14.00 12.500 0.750 20.00 80 494.00
❖ 24 x 12 24.00 21.562 1.219 12.75 11.374 0.688 20.00 80 494.00
❖ 24 x 10 24.00 21.562 1.219 10.75 9.562 0.594 20.00 80 494.00
70

TEL: 708/594-1700
FAX: 708/458-0106
NOTES Schedule 160
or estimated.
paragraph 4.4.2.

Number Pounds
3/4 x 1/2 1.05 0.612 0.219 0.84 0.464 0.188 1.50 160 0.37
FITTINGS
1 x 3/4 1.32 0.820 0.250 1.05 0.612 0.219 2.00 160 0.45
1 x 1/2 1.32 0.820 0.250 0.84 0.464 0.188 2.00 160 0.45
1 1/4 x 1 1.66 1.160 0.250 1.32 0.820 0.250 2.00 160 0.70
1 1/4 x 3/4 1.66 1.160 0.250 1.05 0.612 0.219 2.00 160 0.70
1 1/4 x 1/2 1.66 1.160 0.250 0.84 0.464 0.188 2.00 160 0.70
1 1/2 x 1 1/4 1.90 1.338 0.281 1.66 1.160 0.250 2.50 160 0.90
1 1/2 x 1 1.90 1.338 0.281 1.32 0.820 0.250 2.50 160 0.90
1 1/2 x 3/4 1.90 1.338 0.281 1.05 0.612 0.219 2.50 160 0.90
1 1/2 x 1/2 1.90 1.338 0.281 0.84 0.464 0.188 2.50 160 0.90
2 x 1 1/2 2.38 1.692 0.344 1.90 1.338 0.281 3.00 160 1.85
2 x 1 1/4 2.38 1.692 0.344 1.66 1.160 0.250 3.00 160 1.85
2x1 2.38 1.692 0.344 1.32 0.820 0.250 3.00 160 1.85
2 x 3/4 2.38 1.692 0.344 1.05 0.612 0.219 3.00 160 1.50
2 1/2 x 2 2.88 2.130 0.375 2.38 1.692 0.344 3.50 160 3.00
2 1/2 x 1 1/2 2.88 2.130 0.375 1.90 1.338 0.281 3.50 160 3.00
2 1/2 x 1 1/4 2.88 2.130 0.375 1.66 1.160 0.250 3.50 160 2.80
2 1/2 x 1 2.88 2.130 0.375 1.32 0.820 0.250 3.50 160 2.80
3 x 2 1/2 3.50 2.624 0.438 2.88 2.130 0.375 3.50 160 4.00
3x2 3.50 2.624 0.438 2.38 1.692 0.344 3.50 160 4.00
3 x 1 1/2 3.50 2.624 0.438 1.90 1.338 0.281 3.50 160 4.00
3 x 1 1/4 3.50 2.624 0.438 1.66 1.160 0.250 3.50 160 3.50
❖ 3x1 3.50 2.624 0.438 1.32 0.820 0.250 3.50 160 3.50
4x3 4.50 3.438 0.531 3.50 2.624 0.438 4.00 160 6.00
4 x 2 1/2 4.50 3.438 0.531 2.88 2.130 0.375 4.00 160 6.00
4x2 4.50 3.438 0.531 2.38 1.692 0.344 4.00 160 5.00
4 x 1 1/2 4.50 3.438 0.531 1.90 1.338 0.281 4.00 160 5.00
❖ 4 x 1 1/4 4.50 3.438 0.531 1.66 1.160 0.250 4.00 160 5.00
❖ 4x1 4.50 3.438 0.531 1.32 0.820 0.250 4.00 160 5.00
71

Schedule 160 NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
5x4 5.56 4.310 0.625 4.50 3.438 0.531 5.00 160 14.00
5x3 5.56 4.310 0.625 3.50 2.624 0.438 5.00 160 14.00
5 x 2 1/2 5.56 4.310 0.625 2.88 2.130 0.375 5.00 160 14.00
5x2 5.56 4.310 0.625 2.38 1.692 0.344 5.00 160 14.00
6x5 6.62 5.182 0.719 5.56 4.310 0.625 5.50 160 18.00
6x4 6.62 5.182 0.719 4.50 3.438 0.531 5.50 160 18.00
6x3 6.62 5.182 0.719 3.50 2.624 0.438 5.50 160 15.50
6 x 2 1/2 6.62 5.182 0.719 2.88 2.130 0.375 5.50 160 15.50
❖ 6x2 6.62 5.182 0.719 2.38 1.692 0.344 5.50 160 15.00
8x6 8.62 6.808 0.906 6.62 5.182 0.719 6.00 160 31.50
8x5 8.62 6.808 0.906 5.56 4.310 0.625 6.00 160 28.00
8x4 8.62 6.808 0.906 4.50 3.438 0.531 6.00 160 28.00
❖ 8x3 8.62 6.808 0.906 3.50 2.624 0.438 6.00 160 30.00
10 x 8 10.75 8.500 1.125 8.62 6.808 0.906 7.00 160 58.00
10 x 6 10.75 8.500 1.125 6.62 5.182 0.719 7.00 160 58.00
10 x 5 10.75 8.500 1.125 5.56 4.310 0.625 7.00 160 54.00
10 x 4 10.75 8.500 1.125 4.50 3.438 0.531 7.00 160 52.00
12 x 10 12.75 10.126 1.312 10.75 8.500 1.125 8.00 160 95.00
12 x 8 12.75 10.126 1.312 8.62 6.808 0.906 8.00 160 85.00
12 x 6 12.75 10.126 1.312 6.62 5.182 0.719 8.00 160 80.00
12 x 5 12.75 10.126 1.312 5.56 4.310 0.625 8.00 160 80.00
❖ 12 x 4 12.75 10.126 1.312 4.50 3.438 0.531 8.00 160 80.00
14 x 12 14.00 11.188 1.406 12.75 10.126 1.312 13.00 160 115.00
14 x 10 14.00 11.188 1.406 10.75 8.500 1.125 13.00 160 115.00
14 x 8 14.00 11.188 1.406 8.62 6.808 0.906 13.00 160 159.00
14 x 6 14.00 11.188 1.406 6.62 5.182 0.719 13.00 160 159.00
16 x 14 16.00 12.812 1.594 14.00 11.188 1.406 14.00 160 159.00
16 x 12 16.00 12.812 1.594 12.75 10.126 1.312 14.00 160 159.00
16 x 10 16.00 12.812 1.594 10.75 8.500 1.125 14.00 160 159.00
16 x 8 16.00 12.812 1.594 8.62 6.808 0.906 14.00 160 213.00
❖ 16 x 6 16.00 12.812 1.594 6.62 5.182 0.719 14.00 160 213.00
72

TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
18 x 16 18.00 14.438 1.781 16.00 12.812 1.594 15.00 160 213.00
18 x 14 18.00 14.438 1.781 14.00 11.188 1.406 15.00 160 213.00
18 x 12 18.00 14.438 1.781 12.75 10.126 1.312 15.00 160 213.00
18 x 10 18.00 14.438 1.781 10.75 8.500 1.125 15.00 160 348.00
❖ 18 x 8 18.00 14.438 1.781 8.62 6.808 0.906 15.00 160 327.00
20 x 18 20.00 16.062 1.969 18.00 14.438 1.781 20.00 160 348.00
20 x 16 20.00 16.062 1.969 16.00 12.812 1.594 20.00 160 348.00
20 x 14 20.00 16.062 1.969 14.00 11.188 1.406 20.00 160 494.00
20 x 12 20.00 16.062 1.969 12.75 10.126 1.312 20.00 160 494.00
❖ 20 x 10 20.00 16.062 1.969 10.75 8.500 1.125 20.00 160 494.00
24 x 20 24.00 19.312 2.344 20.00 16.062 1.969 20.00 160 494.00
24 x 18 24.00 19.312 2.344 18.00 14.438 1.781 20.00 160 535.00
FITTINGS
24 x 16 24.00 19.312 2.344 16.00 12.812 1.594 20.00 160 535.00
❖ 24 x 14 24.00 19.312 2.344 14.00 11.188 1.406 20.00 160 535.00
❖ 24 x 12 24.00 19.312 2.344 12.75 10.126 1.312 20.00 160 535.00
❖ 24 x 10 24.00 19.312 2.344 10.75 8.500 1.125 20.00 160 535.00
73

Schedule XXS NOTES
or estimated.
paragraph 4.4.2.

Number Pounds
FITTINGS
3/4 x 1/2 1.05 0.434 0.308 0.84 0.252 0.294 1.50 * 0.39
1 x 3/4 1.32 0.604 0.358 1.05 0.434 0.308 2.00 * 0.50
1 x 1/2 1.32 0.604 0.358 0.84 0.252 0.294 2.00 * 0.50
1 1/4 x 1 1.66 0.896 0.382 1.32 0.604 0.358 2.00 * 0.75
1 1/4 x 3/4 1.66 0.896 0.382 1.05 0.434 0.308 2.00 * 0.75
1 1/4 x 1/2 1.66 0.896 0.382 0.84 0.252 0.294 2.00 * 0.75
1 1/2 x 1 1/4 1.90 1.100 0.400 1.66 0.896 0.382 2.50 * 1.00
1 1/2 x 1 1.90 1.100 0.400 1.32 0.604 0.358 2.50 * 1.00
1 1/2 x 3/4 1.90 1.100 0.400 1.05 0.434 0.308 2.50 * 1.00
1 1/2 x 1/2 1.90 1.100 0.400 0.84 0.252 0.294 2.50 * 1.00
2 x 1 1/2 2.38 1.508 0.436 1.90 1.100 0.400 3.00 * 2.00
2 x 1 1/4 2.38 1.508 0.436 1.66 0.896 0.382 3.00 * 2.00
2x1 2.38 1.508 0.436 1.32 0.604 0.358 3.00 * 2.00
2 x 3/4 2.38 1.508 0.436 1.05 0.434 0.308 3.00 * 1.75
2 1/2 x 2 2.88 1.776 0.552 2.38 1.508 0.436 3.50 * 4.00
2 1/2 x 1 1/2 2.88 1.776 0.552 1.90 1.100 0.400 3.50 * 4.00
2 1/2 x 1 1/4 2.88 1.776 0.552 1.66 0.896 0.382 3.50 * 3.50
2 1/2 x 1 2.88 1.776 0.552 1.32 0.604 0.358 3.50 * 3.50
3 x 2 1/2 3.50 2.300 0.600 2.88 1.776 0.552 3.50 * 5.00
3x2 3.50 2.300 0.600 2.38 1.508 0.436 3.50 * 5.00
3 x 1 1/2 3.50 2.300 0.600 1.90 1.100 0.400 3.50 * 5.00
3 x 1 1/4 3.50 2.300 0.600 1.66 0.896 0.382 3.50 * 4.50
❖3x1 3.50 2.300 0.600 1.32 0.604 0.358 3.50 * 4.50
4x3 4.50 3.152 0.674 3.50 2.300 0.600 4.00 * 8.00
4 x 2 1/2 4.50 3.152 0.674 2.88 1.776 0.552 4.00 * 8.00
4x2 4.50 3.152 0.674 2.38 1.508 0.436 4.00 * 7.50
4 x 1 1/2 4.50 3.152 0.674 1.90 1.100 0.400 4.00 * 7.50
❖ 4 x 1 1/4 4.50 3.152 0.674 1.66 0.896 0.382 4.00 * 7.50
❖4x1 4.50 3.152 0.674 1.32 0.604 0.358 4.00 * 7.00
74

TEL: 708/594-1700
FAX: 708/458-0106

Number Pounds
5x4 5.56 4.060 0.750 4.50 3.152 0.674 5.00 * 16.00
5x3 5.56 4.060 0.750 3.50 2.300 0.600 5.00 * 16.00
5 x 2 1/2 5.56 4.060 0.750 2.88 1.776 0.552 5.00 * 16.00
5x2 5.56 4.060 0.750 2.38 1.508 0.436 5.00 * 16.00
6x5 6.62 4.892 0.864 5.56 4.060 0.750 5.50 * 23.00
6x4 6.62 4.892 0.864 4.50 3.152 0.674 5.50 * 23.00
6x3 6.62 4.892 0.864 3.50 2.300 0.600 5.50 * 20.00
6 x 2 1/2 6.62 4.892 0.864 2.88 1.776 0.552 5.50 * 20.00
❖6x2 6.62 4.892 0.864 2.38 1.508 0.436 5.50 * 19.00
8x6 8.62 6.870 0.875 6.62 4.892 0.864 6.00 * 36.00
8x5 8.62 6.870 0.875 5.56 4.060 0.750 6.00 * 33.00
8x4 8.62 6.870 0.875 4.50 3.152 0.674 6.00 * 33.00
FITTINGS
❖8x3 8.62 6.870 0.875 3.50 2.300 0.600 6.00 * 33.00
10 x 8 10.75 8.750 1.000 8.62 6.870 0.875 7.00 * 48.00
10 x 6 10.75 8.750 1.000 6.62 4.892 0.864 7.00 * 58.00
10 x 5 10.75 8.750 1.000 5.56 4.060 0.750 7.00 * 54.00
10 x 4 10.75 8.750 1.000 4.50 3.152 0.674 7.00 * 52.00
12 x 10 12.75 10.750 1.000 10.75 8.750 1.000 8.00 * 95.00
12 x 8 12.75 10.750 1.000 8.62 6.870 0.875 8.00 * 85.00
12 x 6 12.75 10.750 1.000 6.62 4.892 0.864 8.00 * 80.00
12 x 5 12.75 10.750 1.000 5.56 4.060 0.750 8.00 * 80.00
❖ 12 x 4 12.75 10.750 1.000 4.50 3.152 0.674 8.00 * 80.00
75

CAPS
SCHEDULE STD Outside Inside Wall Height Pipe Approx.
Pipe Diameter Diameter Thickness Schedule Weight in
Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.622 0.109 1.00 40 0.08
3/4 1.05 0.824 0.113 1.00 40 0.14
1 1.32 1.049 0.133 1.50 40 0.21
1 1/4 1.66 1.380 0.140 1.50 40 0.33
1 1/2 1.90 1.610 0.145 1.50 40 0.54
2 2.38 2.067 0.154 1.50 40 0.80
2 1/2 2.88 2.469 0.203 1.50 40 1.00
3 3.50 3.068 0.216 2.00 40 1.70
3 1/2 4.00 3.548 0.226 2.50 40 2.30
4 4.50 4.026 0.237 2.50 40 2.80
5 5.56 5.047 0.258 3.00 40 4.60
6 6.62 6.065 0.280 3.50 40 6.90
8 8.62 7.981 0.322 4.00 40 11.80
10 10.75 10.020 0.365 5.00 40 20.80
12 12.75 12.000 0.375 6.00 * 30.30
FITTINGS
14 14.00 13.250 0.375 6.50 30 36.50

NOTES 16 16.00 15.250 0.375 7.00 30 43.50
3. For bevel detail see page 107. 20 20.00 19.250 0.375 9.00 20 75.70
4. For dimensional tolerances see page 108. 24 24.00 23.250 0.375 10.50 20 101.00
or estimated.
7. The shape of the cap is 2:1 ellipsoidal and 36 36.00 35.250 0.375 10.50 * 175.00
conforms to the shape requirements given 42 42.00 41.250 0.375 12.00 * 229.00
in the ASME Boiler and Pressure Vessel Code.
* This size and thickness does not correspond 48 48.00 47.250 0.375 13.50 * 350.00
SCHEDULE XS Outside Inside Wall Height Pipe Approx.

Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.546 0.147 1.00 80 0.10
3/4 1.05 0.742 0.154 1.00 80 0.16
1 1.32 0.957 0.179 1.50 80 0.28
1 1/4 1.66 1.278 0.191 1.50 80 0.48
1 1/2 1.90 1.500 0.200 1.50 80 0.67
2 2.38 1.939 0.218 1.50 80 0.92
2 1/2 2.88 2.323 0.276 1.50 80 1.30
3 3.50 2.900 0.300 2.00 80 2.10
3 1/2 4.00 3.364 0.318 2.50 80 3.00
4 4.50 3.826 0.337 2.50 80 3.50
5 5.56 4.813 0.375 3.00 80 5.80
6 6.62 5.761 0.432 3.50 80 9.30
8 8.62 7.625 0.500 4.00 80 16.00
10 10.75 9.750 0.500 5.00 60 26.00
12 12.75 11.750 0.500 6.00 * 38.00
14 14.00 13.000 0.500 6.50 * 47.00
NOTES 16 16.00 15.000 0.500 7.00 40 57.00
4. For dimensional tolerances see page 108. 24 24.00 23.000 0.500 10.50 * 145.00
30 30.00 29.000 0.500 10.50 20 634.00
or estimated. 36 36.00 35.000 0.500 10.50 20 913.00
7. The shape of the cap is 2:1 ellipsoidal and
conforms to the shape requirements given
42 42.00 41.000 0.500 12.00 * 1300.00
in the ASME Boiler and Pressure Vessel Code. 48 48.00 47.000 0.500 13.50 * 1675.00
76 to any pipe schedule number.

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com CAPS
Outside Inside Wall Height Pipe Approx. Schedule 40

Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.622 0.109 1.00 40 0.08
3/4 1.05 0.824 0.113 1.00 40 0.14
1 1.32 1.054 0.133 1.50 40 0.21
1 1/4 1.66 1.380 0.140 1.50 40 0.33
1 1/2 1.90 1.610 0.145 1.50 40 0.54
2 2.38 2.072 0.154 1.50 40 0.80
2 1/2 2.88 2.474 0.203 1.50 40 1.00
3 3.50 3.068 0.216 2.00 40 1.70
3 1/2 4.00 3.548 0.226 2.50 40 2.30
4 4.50 4.026 0.237 2.50 40 2.80
5 5.56 5.044 0.258 3.00 40 4.60
6 6.62 6.060 0.280 3.50 40 6.90
8 8.62 7.976 0.322 4.00 40 11.80
10 10.75 10.020 0.365 5.00 40 20.80
12 12.75 11.938 0.406 6.00 40 30.30
FITTINGS
14 14.00 13.124 0.438 6.50 40 36.50
16 16.00 15.000 0.500 7.00 40 43.50 NOTES
20 20.00 18.812 0.594 10.00 40 75.70 3. For bevel detail see page 107.
or estimated.
Outside Inside Wall Height Pipe Approx. SCHEDULE 80

Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.546 0.147 1.00 80 0.10
3/4 1.05 0.742 0.154 1.00 80 0.16
1 1.32 0.962 0.179 1.50 80 0.28
1 1/4 1.66 1.278 0.191 1.50 80 0.48
1 1/2 1.90 1.500 0.200 1.50 80 0.67
2 2.38 1.944 0.218 1.50 80 0.92
2 1/2 2.88 2.328 0.276 1.50 80 1.30
3 3.50 2.900 0.300 2.00 80 2.10
3 1/2 4.00 3.364 0.318 2.50 80 3.00
4 4.50 3.826 0.337 2.50 80 3.50
5 5.56 4.810 0.375 3.00 80 5.80
6 6.62 5.756 0.432 3.50 80 9.30
8 8.62 7.620 0.500 4.00 80 16.00
10 10.75 9.562 0.594 6.00 80 26.00
12 12.75 11.374 0.688 7.00 80 38.00
14 14.00 12.500 0.750 7.50 80 47.00
16 16.00 14.312 0.844 8.00 80 57.00 NOTES
or estimated.
77

caps
SCHEDULE 160 Outside Inside Wall Height Pipe Approx.
Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.464 0.188 1.00 160 0.30
3/4 1.05 0.612 0.219 1.00 160 0.30
1 1.32 0.820 0.250 1.50 160 0.40
1 1/4 1.66 1.160 0.250 1.50 160 0.50
1 1/2 1.90 1.338 0.281 1.50 160 0.60
2 2.38 1.692 0.344 1.75 160 1.30
2 1/2 2.88 2.130 0.375 2.00 160 1.80
3 3.50 2.624 0.438 2.50 160 2.90
4 4.50 3.438 0.531 3.00 160 5.90
5 5.56 4.310 0.625 3.50 160 10.00
6 6.62 5.182 0.719 4.00 160 15.00
8 8.62 6.808 0.906 5.00 160 31.00
10 10.75 8.500 1.125 6.00 160 57.00
12 12.75 10.126 1.312 7.00 160 95.00
14 14.00 11.188 1.406 7.50 160 200.00
FITTINGS
16 16.00 12.812 1.594 8.00 160 297.00

NOTES 18 18.00 14.438 1.781 9.00 160 360.00
or estimated.
SCHEDULE XXS Outside Inside Wall Height Pipe Approx.

Size Number Pounds
O.D. I.D. T H
1/2 0.84 0.252 0.294 1.00 * 0.50
3/4 1.05 0.434 0.308 1.00 * 0.75
1 1.32 0.604 0.358 1.50 * 1.00
1 1/4 1.66 0.896 0.382 1.50 * 1.50
1 1/2 1.90 1.100 0.400 1.50 * 2.50
2 2.38 1.508 0.436 1.75 * 3.00
2 1/2 2.88 1.776 0.552 2.00 * 4.00
3 3.50 2.300 0.600 2.50 * 6.00
4 4.50 3.152 0.674 3.00 * 9.00
5 5.56 4.060 0.750 3.50 * 13.50
6 6.62 4.892 0.864 4.00 * 18.00
8 8.62 6.870 0.875 5.00 * 26.00
10 10.75 8.750 1.000 6.00 140 46.00
12 12.75 10.750 1.000 7.00 120 68.00
NOTES
or estimated.
78

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com lap joint stub ends
Outside Outside Wall and Lap Lap Fillet Overall Pipe Approx.
Schedule STD
Pipe Diameter Diameter Thickness Diameter Radius Length Schedule Weight in
Size (Max.) (Min.) Number Pounds
T K N J
1/2 0.896 0.809 0.109 1.38 0.12 3.00 40 0.30
3/4 1.106 1.019 0.113 1.69 0.12 3.00 40 0.40
1 1.376 1.284 0.133 2.00 0.12 4.00 40 0.75
1 1/4 1.716 1.629 0.140 2.50 0.19 4.00 40 1.10
1 1/2 1.965 1.869 0.145 2.88 0.25 4.00 40 1.25
2 2.456 2.344 0.154 3.62 0.31 6.00 40 2.25
2 1/2 2.966 2.844 0.203 4.12 0.31 6.00 40 3.50
3 3.596 3.469 0.216 5.00 0.38 6.00 40 4.75
3 1/2 4.096 3.969 0.226 5.50 0.38 6.00 40 6.00
4 4.593 4.469 0.237 6.19 0.44 6.00 40 7.25
5 5.683 5.532 0.258 7.31 0.44 8.00 40 12.00
6 6.743 6.594 0.280 8.50 0.50 8.00 40 16.00
8 8.743 8.594 0.322 10.62 0.50 8.00 40 23.00
10 10.913 10.719 0.365 12.75 0.50 10.00 40 36.00
12 12.913 12.719 0.375 15.00 0.50 10.00 * 47.00
FITTINGS
14 14.170 13.969 0.375 16.25 0.50 12.00 30 35.40
16 16.180 15.969 0.375 18.50 0.50 12.00 30 44.80 NOTES
18 18.190 17.969 0.375 21.00 0.50 12.00 * 57.20 1. Conforms to ASME B16.9 & ASTM A234 WPB.
20 20.240 19.969 0.375 23.00 0.50 12.00 20 71.00 2. All dimensions are in inches.
24 24.240 23.969 0.375 27.25 0.50 12.00 20 102.00 3. For bevel detail see page 107.
or estimated.
SCHEDULE XS
T K N J
1/2 0.896 0.809 0.147 1.38 0.12 3.00 80 0.38
3/4 1.106 1.019 0.154 1.69 0.12 3.00 80 0.51
1 1.376 1.284 0.179 2.00 0.12 4.00 80 1.00
1 1/4 1.716 1.629 0.191 2.50 0.19 4.00 80 1.25
1 1/2 1.965 1.869 0.200 2.88 0.25 4.00 80 1.75
2 2.456 2.344 0.218 3.62 0.31 6.00 80 3.00
2 1/2 2.966 2.844 0.276 4.12 0.31 6.00 80 4.50
3 3.596 3.469 0.300 5.00 0.38 6.00 80 6.50
3 1/2 4.096 3.969 0.318 5.50 0.38 6.00 80 7.75
4 4.593 4.469 0.337 6.19 0.44 6.00 80 9.50
5 5.683 5.532 0.375 7.31 0.44 8.00 80 17.00
6 6.743 6.594 0.432 8.50 0.50 8.00 80 23.00
8 8.743 8.594 0.500 10.62 0.50 8.00 80 32.00
10 10.913 10.719 0.500 12.75 0.50 10.00 60 53.00
12 12.913 12.719 0.500 15.00 0.50 10.00 * 62.00
14 14.170 13.969 0.500 16.25 0.50 12.00 * 89.00
16 16.180 15.969 0.500 18.50 0.50 12.00 40 96.00 NOTES
18 18.190 17.969 0.500 21.00 0.50 12.00 * 112.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
24 24.240 23.969 0.500 27.25 0.50 12.00 * 151.00 3. For bevel detail see page 107.
or estimated.
79

lap joint stub ends
SCHEDULE 40 Outside Outside Wall and Lap Lap Fillet Overall Pipe Approx.
T K N J
1/2 0.896 0.809 0.109 1.38 0.12 3.00 40 0.30
3/4 1.106 1.019 0.113 1.69 0.12 3.00 40 0.40
1 1.376 1.284 0.133 2.00 0.12 4.00 40 0.75
1 1/4 1.716 1.629 0.140 2.50 0.19 4.00 40 1.10
1 1/2 1.965 1.869 0.145 2.88 0.25 4.00 40 1.25
2 2.456 2.344 0.154 3.62 0.31 6.00 40 2.25
2 1/2 2.966 2.844 0.203 4.12 0.31 6.00 40 3.50
3 3.596 3.469 0.216 5.00 0.38 6.00 40 4.75
3 1/2 4.096 3.969 0.226 5.50 0.38 6.00 40 6.00
4 4.593 4.469 0.237 6.19 0.44 6.00 40 7.25
5 5.683 5.532 0.258 7.31 0.44 8.00 40 12.00
6 6.743 6.594 0.280 8.50 0.50 8.00 40 16.00
8 8.743 8.594 0.322 10.62 0.50 8.00 40 23.00
10 10.913 10.719 0.365 12.75 0.50 10.00 40 36.00
12 12.913 12.719 0.406 15.00 0.50 10.00 40 52.00
FITTINGS
14 14.170 13.969 0.438 16.25 0.50 12.00 40 73.00

NOTES 16 16.180 15.969 0.500 18.50 0.50 12.00 40 97.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 18 18.190 17.969 0.562 21.00 0.50 12.00 40 126.00
2. All dimensions are in inches. 20 20.240 19.969 0.594 23.00 0.50 12.00 40 147.00
3. For bevel detail see page 107. 24 24.240 23.969 0.688 27.25 0.50 12.00 40 205.00
or estimated.
SCHEDULE 80 Outside Outside Wall and Lap Lap Fillet Overall Pipe Approx.
T K N J
1/2 0.896 0.809 0.147 1.38 0.12 3.00 80 0.38
3/4 1.106 1.019 0.154 1.69 0.12 3.00 80 0.51
1 1.376 1.284 0.179 2.00 0.12 4.00 80 1.00
1 1/4 1.716 1.629 0.191 2.50 0.19 4.00 80 1.25
1 1/2 1.965 1.869 0.200 2.88 0.25 4.00 80 1.75
2 2.456 2.344 0.218 3.62 0.31 6.00 80 3.00
2 1/2 2.966 2.844 0.276 4.12 0.31 6.00 80 4.50
3 3.596 3.469 0.300 5.00 0.38 6.00 80 6.50
3 1/2 4.096 3.969 0.318 5.50 0.38 6.00 80 7.75
4 4.593 4.469 0.337 6.19 0.44 6.00 80 9.50
5 5.683 5.532 0.375 7.31 0.44 8.00 80 17.00
6 6.743 6.594 0.432 8.50 0.50 8.00 80 23.00
8 8.743 8.594 0.500 10.62 0.50 8.00 80 32.00
10 10.913 10.719 0.594 12.75 0.50 10.00 80 63.00
12 12.913 12.719 0.688 15.00 0.50 10.00 80 87.00
14 14.170 13.969 0.750 16.25 0.50 12.00 80 123.00
NOTES 16 16.180 15.969 0.844 18.50 0.50 12.00 80 161.00
1. Conforms to ASME B16.9 & ASTM A234 WPB. 18 18.190 17.969 0.938 21.00 0.50 12.00 80 205.00
2. All dimensions are in inches. 20 20.240 19.969 1.031 23.00 0.50 12.00 80 251.00
3. For bevel detail see page 107. 24 24.240 23.969 1.219 27.25 0.50 12.00 80 359.00
or estimated.
80

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com lap joint stub ends
Schedule 160
T K N J
1/2 0.896 0.809 0.188 1.38 0.12 3.00 160 0.75
3/4 1.106 1.019 0.219 1.69 0.12 3.00 160 0.95
1 1.376 1.284 0.250 2.00 0.12 4.00 160 1.13
1 1/4 1.716 1.629 0.250 2.50 0.19 4.00 160 1.51
1 1/2 1.965 1.869 0.281 2.88 0.25 4.00 160 2.02
2 2.456 2.344 0.344 3.62 0.31 6.00 160 4.51
2 1/2 2.966 2.844 0.375 4.12 0.31 6.00 160 6.02
3 3.596 3.469 0.438 5.00 0.38 6.00 160 8.80
4 4.593 4.469 0.531 6.19 0.44 6.00 160 14.10
5 5.683 5.532 0.625 7.31 0.44 8.00 160 26.40
6 6.743 6.594 0.719 8.50 0.50 8.00 160 36.40
8 8.743 8.594 0.906 10.62 0.50 8.00 160 60.00
10 10.913 10.719 1.125 12.75 0.50 10.00 160 113.00
12 12.913 12.719 1.312 15.00 0.50 10.00 160 160.00
14 14.170 13.969 1.406 16.25 0.50 12.00 160 190.00
FITTINGS
16 16.180 15.969 1.594 18.50 0.50 12.00 160 245.00
18 18.190 17.969 1.781 21.00 0.50 12.00 160 309.00 NOTES
20 20.240 19.969 1.969 23.00 0.50 12.00 160 379.00 1. Conforms to ASME B16.9 & ASTM A234 WPB.
or estimated.
SCHEDULE XXS
T K N J
1/2 0.896 0.809 0.294 1.38 0.12 3.00 * 1.75
3/4 1.106 1.019 0.308 1.69 0.12 3.00 * 2.50
1 1.376 1.284 0.358 2.00 0.12 4.00 * 4.00
1 1/4 1.716 1.629 0.382 2.50 0.19 4.00 * 6.25
1 1/2 1.965 1.869 0.400 2.88 0.25 4.00 * 6.50
2 2.456 2.344 0.436 3.62 0.31 6.00 * 9.00
2 1/2 2.966 2.844 0.552 4.12 0.31 6.00 * 14.00
3 3.596 3.469 0.600 5.00 0.38 6.00 * 18.50
4 4.593 4.469 0.674 6.19 0.44 6.00 * 27.50
5 5.683 5.532 0.750 7.31 0.44 8.00 * 39.00
6 6.743 6.594 0.864 8.50 0.50 8.00 * 54.00
8 8.743 8.594 0.875 10.62 0.50 8.00 * 73.00
10 10.913 10.719 1.000 12.75 0.50 10.00 140 116.00
12 12.913 12.719 1.000 15.00 0.50 10.00 120 167.00
NOTES
or estimated.
81

Box quantities
Box Quantities Short Radius 90° Elbows Long Radius 90° Elbows Straight Tees Caps
Size / Wall STD XS STD XS STD XS STD XS
1/2" — — 6-bag 6-bag 6-bag 6-bag — —
3/4" — — 4-bag 4-bag 6-bag 6-bag 6-bag 6-bag
1" — — 4-bag 4-bag 6-bag 6-bag 6-bag 6-bag
1 1/4" — — 12 4-bag 6-bag 6-bag 6-bag 6-bag
1 1/2" — — 12 4-bag 6-bag 6-bag 6-bag 6-bag
2" — — 12 12 — — 12 12
2 1/2" — — 12 12 12 — 12 12
3" — — 12 12 6 — 12 12
3 1/2" — — 8 8 — — — —
4" — — 12 12 6 — 12 12
5" — — 6 6 — — 6 6
6" — — 4 4 4 — 6 6
FITTINGS
8" — — 1 1 — — 4 4
10" — — 1 1 — — 2 2
12" — — 1 1 — — 2 2
Box Quantities Reducing Tees Concentric Reducers Eccentric Reducers
Size / Wall STD XS STD XS STD XS
3/4 x 1/2" 6-bag 6-bag — — — —
1 x 1/2" 6-bag 6-bag — — — —
1 x 3/4" 6-bag 6-bag — — — —
1 1/4 x 1/2" 6-bag 6-bag — — — —
1 1/4 x 1" 6-bag 6-bag — — — —
1 1/2 x 1/2" 6-bag 6-bag — — — —
1 1/2 x 3/4" 6-bag 6-bag — — — —
1 1/2 x 1" 6-bag 6-bag — — — —
1 1/2 x 1 1/4" 6-bag 6-bag — — — —
2 x 1" — — 12 12 12 —
2 x 1 1/4" — — 12 12 12 —
2 x 1 1/2" — — 12 12 12 —
2 1/2 x 1 1/4" — — 12 12 12 —
2 1/2 x 1 1/2" — — 12 12 12 —
2 1/2 x 2" — — 12 12 12 —
3 x 1 1/2" — — 12 12 12 —
3 x 2" — — 12 12 12 —
3 x 2 1/2" — — 12 12 12 —
4 x 2" 6 — 12 12 12 —
4 x 2 1/2" 6 — 12 12 12 —
4 x 3" 6 — 12 12 12 —
5 x 2 1/2" — — 6 6 6 —
5 x 3" 6 6 6 —
5 x 4" 6 6 6 —
6 x 3" 6 6 6 —
6 x 4" 6 6 6 —
6 x 5" 6 6 6 —
82

Flanges
FLANGES
1/2" through 60"
• Class 125
• Class 150
• Class 300
• Class 600
• Class 900
• Class 1500
• Class 2500
For Ring Type Joint Facing Dimension information see page 148-153.
FLANGES
All Products Backed by the Weldbend Warranty
84

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com Class 125 steel pipe flanges▼
Formula for determining bolt lengths (P) see page 159.
Common Dimensions Length Through Hub Bore Diameter Approx. Weight Pounds Drilling Template
of
Outside Thickness Diameter Diameter
Pipe Weld Weld
at Base Slip-On Slip-On Hub at of Bolt Number Diameter Diameter
Size Diameter Neck Neck Bevel Weld Neck Slip-On of Bolt of Bolt
of Hub Circle of Bolts
Holes Holes
O.D. C W Y1 Y2 B1 B2 K M
30 38.75 2.13 32.75 5.13 3.50 To be specified by 30.19 30.00 340.00 305.00 36.00 28 1 3/8 1 1/4
36 46.00 2.38 39.25 5.38 3.75 purchaser. 36.19 36.00 495.00 450.00 42.75 32 1 5/8 1 1/2
42 53.00 2.63 46.00 5.63 4.00 42.19 42.00 710.00 650.00 49.50 36 1 5/8 1 1/2
48 59.50 2.75 52.25 5.75 4.13 48.19 48.00 870.00 800.00 56.00 44 1 5/8 1 1/2
54 66.25 3.00 58.75 6.00 4.34 54.19 54.00 1100.00 1025.00 62.75 44 2 1 3/4
60 73.00 3.13 65.25 6.13 4.50 60.19 60.00 1350.00 1250.00 69.25 52 2 1 3/4
NOTES
1. Standard flange facings on page 146. 5. All weights are in pounds and approximated or estimated. Class 125 flanges are wide in face and used for connections to cast steel
2. All dimensions are in inches. ▼T here is no standard for Class 125 as it is applicable valves or equipment containing flanged ends made to Cast Iron Standard
3. For dimensional tolerances see page 144. to Cast Iron Standard ASME B16.1. These flanges correspond dimensions. Carbon steel bolting is intended and alloy studs should be
4. All flanges conform to ASTM A105/ASME SA105. to ASME B16.1 in diameter, thickness, and drilling. avoided. Class 125 flanges are identical with Class E AWWA.
FLANGES
85

Class 150 steel pipe flanges
For Ring Type Joint Facing Dimension information see page 148.
Bolting Pattern and Bolt Lengths

Drilling Length of Bolts
Outside Diameter Stud Bolts Machine Bolts
Pipe Diameter Diameter Number Diameter Stud Bolts
Size of Raised Face Ring Joint Raised Face
Bolt Circle of of of 0.06 in. 0.06 in.
Bolt Holes Bolt Holes Bolts
O.D. M P P P
ASME B16.5
1/2 3.50 2.38 5/8 4 1/2 2.25 * 2.00
3/4 3.88 2.75 5/8 4 1/2 2.50 * 2.00
1 4.25 3.12 5/8 4 1/2 2.50 3.00 2.25
1 1/4 4.62 3.50 5/8 4 1/2 2.75 3.25 2.25
1 1/2 5.00 3.88 5/8 4 1/2 2.75 3.25 2.50
2 6.00 4.75 3/4 4 5/8 3.25 3.75 2.75
2 1/2 7.00 5.50 3/4 4 5/8 3.50 4.00 3.00
3 7.50 6.00 3/4 4 5/8 3.50 4.00 3.00
3 1/2 8.50 7.00 3/4 8 5/8 3.50 4.00 3.00
4 9.00 7.50 3/4 8 5/8 3.50 4.00 3.00
5 10.00 8.50 7/8 8 3/4 3.75 4.25 3.25
6 11.00 9.50 7/8 8 3/4 4.00 4.50 3.25
8 13.50 11.75 7/8 8 3/4 4.25 4.75 3.50
FLANGES
10 16.00 14.25 1 12 7/8 4.50 5.00 4.00

12 19.00 17.00 1 12 7/8 4.75 5.25 4.00
14 21.00 18.75 1 1/8 12 1 5.25 5.75 4.50
16 23.50 21.25 1 1/8 16 1 5.25 5.75 4.50
18 25.00 22.75 1 1/4 16 1 1/8 5.75 6.25 5.00
20 27.50 25.00 1 1/4 20 1 1/8 6.25 6.75 5.50
24 32.00 29.50 1 3/8 20 1 1/4 6.75 7.25 6.00
ASME B16.47 Series A
30 38.75 36.00 1 3/8 28 1 1/4
36 46.00 42.75 1 5/8 32 1 1/2 Formula for determining
bolt lengths (P)
42 53.00 49.50 1 5/8 36 1 1/2 see page 159.
48 59.50 56.00 1 5/8 44 1 1/2
ASME B16.47 Series B
30 34.94 33.31 7/8 44 3/4
36 41.62 39.75 1 44 7/8 Formula for determining
bolt lengths (P)
42 48.25 46.12 1 1/8 48 1 see page 159.
48 54.81 52.56 1 1/4 44 1 1/8
NOTES
1. Standard flange facings on page 146. 5. All flanges conform to ASTM A105/ASME SA105. * This size and thickness does not correspond
2. All dimensions are in inches. 6. All flanges 1/2"-24" conform to ASME B16.5. to any pipe schedule number.
3. Calculated flange weights on page 99. All flanges 30" and larger conform to ASME B16.47.
86 4. For dimensional tolerances see page 144.

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com Class 150 steel pipe flanges
Length Through Hub Bore

Outside Thickness Thickness Diameter Diameter
Threaded, Thread Slip-on Weld Depth
Diameter of of of Lap Lap Joint
Pipe of Slip-on Lap Weld Length & Socket Neck & of
of Flange Lap Joint Weld Joint Radius
Size Hub* & Socket Joint Neck (Min.) Weld Socket Socket
Flange (Min.) (Min.) Neck (Min.)
Weld (Min.) Weld
O.D. C C W K Y2 Y3 Y1 T B2 B3 B1 ▲ J D
ASME B16.5
1/2 3.50 0.38 0.44 1.19 0.84 0.56 0.62 1.81 0.62 0.88 0.90 0.62 0.12 0.38
3/4 3.88 0.44 0.50 1.50 1.05 0.56 0.62 2.00 0.62 1.09 1.11 0.82 0.12 0.44
1 4.25 0.50 0.56 1.94 1.32 0.62 0.69 2.12 0.69 1.36 1.38 1.05 0.12 0.50
1 1/4 4.62 0.56 0.62 2.31 1.66 0.75 0.81 2.19 0.81 1.70 1.72 1.38 0.19 0.56
1 1/2 5.00 0.62 0.69 2.56 1.90 0.81 0.88 2.38 0.88 1.95 1.97 1.61 0.25 0.62
2 6.00 0.69 0.75 3.06 2.38 0.94 1.00 2.44 1.00 2.44 2.46 2.07 0.31 0.69
2 1/2 7.00 0.81 0.88 3.56 2.88 1.06 1.12 2.69 1.12 2.94 2.97 2.47 0.31 0.75
3 7.50 0.88 0.94 4.25 3.50 1.12 1.19 2.69 1.19 3.57 3.60 3.07 0.38 0.81
3 1/2 8.50 0.88 0.94 4.81 4.00 1.19 1.25 2.75 1.25 4.07 4.10 3.55 0.38
4 9.00 0.88 0.94 5.31 4.50 1.25 1.31 2.94 1.31 4.57 4.60 4.03 0.44
5 10.00 0.88 0.94 6.44 5.56 1.38 1.44 3.44 1.44 5.66 5.69 5.05 0.44
6 11.00 0.94 1.00 7.56 6.63 1.50 1.56 3.44 1.56 6.72 6.75 6.07 0.50
8 13.50 1.06 1.12 9.69 8.63 1.69 1.75 3.94 1.75 8.72 8.75 7.98 0.50
10 16.00 1.12 1.19 12.00 10.75 1.88 1.94 3.94 1.94 10.88 10.92 10.02 0.50
FLANGES
12 19.00 1.19 1.25 14.38 12.75 2.12 2.19 4.44 2.19 12.88 12.92 12.00 0.50
14 21.00 1.31 1.38 15.75 14.00 2.19 3.12 4.94 2.25 14.14 14.18 13.25 0.50
16 23.50 1.38 1.44 18.00 16.00 2.44 3.44 4.94 2.50 16.16 16.19 15.25 0.50
18 25.00 1.50 1.56 19.88 18.00 2.62 3.81 5.44 2.69 18.18 18.20 17.25 0.50
20 27.50 1.62 1.69 22.00 20.00 2.81 4.06 5.62 2.88 20.20 20.25 19.25 0.50
24 32.00 1.81 1.88 26.12 24.00 3.19 4.38 5.94 3.25 24.25 24.25 23.25 0.50
WN BLD ASME B16.47 Series A
30 38.75 2.88 2.88 30.75 30.00 5.32
36 46.00 3.50 3.50 36.75 36.00 6.13
42 53.00 3.75 3.75 43.00 42.00 6.69
48 59.50 4.19 4.19 49.12 48.00 7.50
WN BLD ASME B16.47 Series B
30 34.94 1.69 1.94 31.00 30.06 3.88
36 41.62 2.00 2.25 37.19 36.06 4.57
42 48.25 2.25 2.65 43.38 42.12 5.19
48 54.81 2.50 3.00 49.50 48.12 5.82
NOTES
1. Standard flange facings on page 146. 6. Thread standards on page 156. * A taper shall not exceed 7 degrees on threaded, slip-on and lapped flanges.
2. All dimensions are in inches. 7. Blind flanges may be produced with or without hubs. ▲ Dimensions listed for socket weld and weld neck flanges are for Standard
3. Calculated flange weights on page 99. 8. All flanges conform to ASTM A105/ASME SA105. bore unless specified by purchaser.
4. For dimensional tolerances see page 144. 9. All flanges 1/2"-24" conform to ASME B16.5.
5. Weld end preparations on page 154. All flanges 30" and larger conform to ASME B16.47.
87

class 300 steel pipe flanges

Outside Diameter Stud Bolts Machine Bolts
Pipe Diameter Diameter Number Diameter Stud Bolts
Size of Raised Face Ring Joint Raised Face
Bolt Circle of of of 0.06 in. 0.06 in.
O.D. M P P P
ASME B16.5
1/2 3.75 2.62 5/8 4 1/2 2.50 3.00 2.25
3/4 4.62 3.25 3/4 4 5/8 3.00 3.50 2.50
1 4.88 3.50 3/4 4 5/8 3.00 3.50 2.50
1 1/4 5.25 3.88 3/4 4 5/8 3.25 3.75 2.75
1 1/2 6.12 4.50 7/8 4 3/4 3.50 4.00 3.00
2 6.50 5.00 3/4 8 5/8 3.50 4.00 3.00
2 1/2 7.50 5.88 7/8 8 3/4 4.00 4.50 3.25
3 8.25 6.62 7/8 8 3/4 4.25 4.75 3.50
3 1/2 9.00 7.25 7/8 8 3/4 4.25 5.00 3.75
4 10.00 7.88 7/8 8 3/4 4.50 5.00 3.75
5 11.00 9.25 7/8 8 3/4 4.75 5.25 4.25
6 12.50 10.62 7/8 12 3/4 4.75 5.50 4.25
8 15.00 13.00 1 12 7/8 5.50 6.00 4.75
FLANGES
10 17.50 15.25 1 1/8 16 1 6.25 6.75 5.50

12 20.50 17.75 1 1/4 16 1 1/8 6.75 7.25 5.75
14 23.00 20.25 1 1/4 20 1 1/8 7.00 7.50 6.25
16 25.50 22.50 1 3/8 20 1 1/4 7.50 8.00 6.50
18 28.00 24.75 1 3/8 24 1 1/4 7.75 8.25 6.75
20 30.50 27.00 1 3/8 24 1 1/4 8.00 8.75 7.25
24 36.00 32.00 1 5/8 24 1 1/2 9.00 10.00 8.00
30 43.00 39.25 1 7/8 28 1 3/4
36 50.00 46.00 2 1/8 32 2 Formula for determining
bolt lengths (P)
42 50.75 47.50 1 3/4 32 1 5/8 see page 159.
48 57.75 54.00 2 32 1 7/8
30 39.00 36.25 1 1/2 36 1 3/8
bolt lengths (P)
42 52.50 49.00 1 7/8 36 1 3/4 see page 159.
48 59.50 55.75 2 40 1 7/8
NOTES
1. Standard flange facings on page 146. 5. All flanges conform to ASTM A105/ASME SA105.
2. All dimensions are in inches. 6. All flanges 1/2"-24" conform to ASME B16.5.

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com class 300 steel pipe flanges
Length Through Hub Bore Min.

Outside Thickness Thickness Diameter Diameter
Threaded, Thread Slip-on Weld Lap Counter Depth
Diameter of of of Lap
Pipe of Slip-on Lap Weld Length & Socket Neck & Joint Bore of
of Flange Lap Joint Weld Joint
Size Flange Hub* & Socket Joint Neck (Min.) Weld Socket Radius Threaded Socket
(Min.) (Min.) Neck (Min.)
Weld (Min.) Weld Flange
O.D. C C W K Y2 Y3 Y1 T B2 B3 B1 ▲ J Z D
ASME B16.5
1/2 3.75 0.50 0.56 1.50 0.84 0.81 0.88 2.00 0.62 0.88 0.90 0.62 0.12 0.93 0.38
3/4 4.62 0.56 0.62 1.88 1.05 0.94 1.00 2.19 0.62 1.09 1.11 0.82 0.12 1.14 0.44
1 4.88 0.62 0.69 2.12 1.32 1.00 1.06 2.38 0.69 1.36 1.38 1.05 0.12 1.41 0.50
1 1/4 5.25 0.69 0.75 2.50 1.66 1.00 1.06 2.50 0.81 1.70 1.72 1.38 0.19 1.75 0.56
1 1/2 6.12 0.75 0.81 2.75 1.90 1.13 1.19 2.63 0.88 1.95 1.97 1.61 0.25 1.98 0.62
2 6.50 0.81 0.88 3.31 2.38 1.25 1.31 2.69 1.12 2.44 2.46 2.07 0.31 2.50 0.69
2 1/2 7.50 0.94 1.00 3.94 2.88 1.44 1.50 2.94 1.25 2.94 2.97 2.47 0.31 3.00 0.75
3 8.25 1.06 1.12 4.62 3.50 1.63 1.69 3.06 1.25 3.57 3.60 3.07 0.38 3.63 0.81
3 1/2 9.00 1.12 1.19 5.25 4.00 1.69 1.75 3.13 1.44 4.07 4.10 3.55 0.38 4.13
4 10.00 1.19 1.25 5.75 4.50 1.82 1.88 3.32 1.44 4.57 4.60 4.03 0.44 4.63
5 11.00 1.31 1.38 7.00 5.56 1.94 2.00 3.82 1.69 5.66 5.69 5.05 0.44 5.69
6 12.50 1.38 1.44 8.12 6.63 2.00 2.06 3.82 1.81 6.72 6.75 6.07 0.50 6.75
8 15.00 1.56 1.62 10.25 8.63 2.38 2.44 4.32 2.00 8.72 8.75 7.98 0.50 8.75
10 17.50 1.81 1.88 12.62 10.75 2.56 3.75 4.56 2.19 10.88 10.92 10.02 0.50 10.88
FLANGES
12 20.50 1.94 2.00 14.75 12.75 2.82 4.00 5.06 2.38 12.88 12.92 12.00 0.50 12.94
14 23.00 2.06 2.12 16.75 14.00 2.94 4.38 5.56 2.50 14.14 14.18 13.25 0.50 14.19
16 25.50 2.19 2.25 19.00 16.00 3.19 4.75 5.69 2.69 16.16 16.19 15.25 0.50 16.19
18 28.00 2.31 2.38 21.00 18.00 3.44 5.12 6.19 2.75 18.18 18.20 17.25 0.50 18.19
20 30.50 2.44 2.50 23.12 20.00 3.69 5.50 6.32 2.88 20.20 20.25 19.25 0.50 20.19
24 36.00 2.69 2.75 27.62 24.00 4.13 6.00 6.56 3.25 24.25 24.25 23.25 0.50 24.19
30 43.00 3.57 3.69 32.56 30.00 8.19
36 50.00 4.07 4.32 39.00 36.00 9.44
42 50.75 4.63 4.63 43.25 42.00 7.82
48 57.75 5.19 5.19 49.38 48.00 8.75
30 39.00 3.63 3.63 32.00 30.25 6.16
36 46.12 4.00 4.00 38.00 36.25 7.06
42 52.50 4.63 4.63 44.00 42.31 8.00
48 59.50 5.00 5.25 50.31 48.31 8.75
NOTES
2. All dimensions are in inches. 7. Blind flanges may be produced with or without hubs. ▲ Dimensions listed for socket weld and weld neck flanges are for Standard
89


Outside Diameter
Pipe Diameter Diameter Number Diameter Raised Face Male & Female /
Size of 0.25 in. Tongue & Groove Ring Joint
Bolt Circle of of of
O.D. M P P P
ASME B16.5
1/2 3.75 2.62 5/8 4 1/2 3.00 2.75 3.00
3/4 4.62 3.25 3/4 4 5/8 3.50 3.25 3.50
1 4.88 3.50 3/4 4 5/8 3.50 3.25 3.50
1 1/4 5.25 3.88 3/4 4 5/8 3.75 3.50 3.75
1 1/2 6.12 4.50 7/8 4 3/4 4.25 4.00 4.25
2 6.50 5.00 3/4 8 5/8 4.25 4.00 4.25
2 1/2 7.50 5.88 7/8 8 3/4 4.75 4.50 4.75
3 8.25 6.62 7/8 8 3/4 5.00 4.75 5.00
3 1/2 9.00 7.25 1 8 7/8 5.50 5.25 5.50
4 10.75 8.50 1 8 7/8 5.75 5.50 5.75
5 13.00 10.50 1 1/8 8 1 6.50 6.25 6.50
6 14.00 11.50 1 1/8 12 1 6.75 6.50 6.75
8 16.50 13.75 1 1/4 12 1 1/8 7.50 7.25 7.75
FLANGES
10 20.00 17.00 1 3/8 16 1 1/4 8.50 8.25 8.50

12 22.00 19.25 1 3/8 20 1 1/4 8.75 8.50 8.75
14 23.75 20.75 1 1/2 20 1 3/8 9.25 9.00 9.25
16 27.00 23.75 1 5/8 20 1 1/2 10.00 9.75 10.00
18 29.25 25.75 1 3/4 20 1 5/8 10.75 10.50 10.75
20 32.00 28.50 1 3/4 24 1 5/8 11.25 11.00 11.50
24 37.00 33.00 2 24 1 7/8 13.00 12.75 13.25
30 44.50 40.25 2 1/8 28 2
bolt lengths (P)
42 55.25 50.50 2 5/8 28 2 1/2 see page 159.
48 62.75 57.50 2 7/8 32 2 3/4
30 40.25 36.50 2 28 1 7/8
bolt lengths (P)
42 see page 159.
48
NOTES

TEL: 708/594-1700
FAX: 708/458-0106

Outside Thickness Diameter Diameter Threaded, Thread Slip-on Weld Lapped Counter Depth
Diameter of of Lap
Pipe of Slip-on Lap Weld Length & Socket Neck & Flange Bore of
of Flange Weld Joint
Size Hub* & Socket Joint Neck (Min.) Weld Socket Radius Threaded Socket
Flange (Min.) Neck (Min.)
O.D. C W K Y2 Y3 Y1 T B2 B3 B1 ▲ J Z D
ASME B16.5
1/2 3.75 0.56 1.50 0.84 0.88 0.88 2.06 0.62 0.88 0.90 .55 0.12 0.93 0.38
3/4 4.62 0.62 1.88 1.05 1.00 1.00 2.25 0.62 1.09 1.11 .74 0.12 1.14 0.44
1 4.88 0.69 2.12 1.32 1.06 1.06 2.44 0.69 1.36 1.38 .96 0.12 1.41 0.50
1 1/4 5.25 0.81 2.50 1.66 1.12 1.12 2.62 0.81 1.70 1.72 1.28 0.19 1.75 0.56
1 1/2 6.12 0.88 2.75 1.90 1.25 1.25 2.75 0.88 1.95 1.97 1.50 0.25 1.99 0.62
2 6.50 1.00 3.31 2.38 1.44 1.44 2.88 1.12 2.44 2.46 1.94 0.31 2.50 0.69
2 1/2 7.50 1.12 3.94 2.88 1.62 1.62 3.12 1.25 2.94 2.97 2.32 0.31 3.00 0.75
3 8.25 1.25 4.62 3.50 1.81 1.81 3.25 1.38 3.57 3.60 2.90 0.38 3.63 0.81
3 1/2 9.00 1.38 5.25 4.00 1.94 1.94 3.38 1.56 4.07 4.10 3.36 0.38 4.13
4 10.75 1.50 6.00 4.50 2.12 2.12 4.00 1.62 4.57 4.60 3.83 0.44 4.63
5 13.00 1.75 7.44 5.56 2.38 2.38 4.50 1.88 5.66 5.69 4.81 0.44 5.69
6 14.00 1.88 8.75 6.63 2.62 2.62 4.62 2.00 6.72 6.75 5.76 0.50 6.75
8 16.50 2.19 10.75 8.63 3.00 3.00 5.25 2.25 8.72 8.75 7.63 0.50 8.75
10 20.00 2.50 13.50 10.75 3.38 4.38 6.00 2.56 10.88 10.92 9.75 0.50 10.88
FLANGES
12 22.00 2.62 15.75 12.75 3.62 4.62 6.12 2.75 12.88 12.92 11.75 0.50 12.94
14 23.75 2.75 17.00 14.00 3.69 5.00 6.50 2.88 14.14 14.18 13.00 0.50 14.19
16 27.00 3.00 19.50 16.00 4.19 5.50 7.00 3.06 16.16 16.19 15.00 0.50 16.19
18 29.25 3.25 21.50 18.00 4.62 6.00 7.25 3.12 18.18 18.20 17.00 0.50 18.19
20 32.00 3.50 24.00 20.00 5.00 6.50 7.50 3.25 20.20 20.25 19.00 0.50 20.19
24 37.00 4.00 28.25 24.00 5.50 7.25 8.00 3.62 24.25 24.25 23.00 0.50 24.19
30 44.50 4.50 5.50 33.94 30.00 9.75
36 51.75 4.88 6.38 40.62 36.00 11.12
42 55.25 6.62 6.75 44.38 42.00 11.00
48 62.75 7.44 7.69 50.75 48.00 12.44
30 40.25 4.94 5.00 31.75 30.00 8.06
36 47.75 5.75 5.94 38.12 36.00 9.56
42
48
NOTES
2. All dimensions are in inches. 7. Blind flanges may be produced with or without hubs. ▲ Dimensions listed for socket weld and weld neck flanges are for Extra-Strong
91


Outside Diameter
O.D. M P P P
ASME B16.5
1/2 4.75 3.25 7/8 4 3/4 4.25 4.00 4.25
3/4 5.12 3.50 7/8 4 3/4 4.50 4.25 4.50
1 5.88 4.00 1 4 7/8 5.00 4.75 5.00
1 1/4 6.25 4.38 1 4 7/8 5.00 4.75 5.00
1 1/2 7.00 4.88 1 1/8 4 1 5.50 5.25 5.50
2 8.50 6.50 1 8 7/8 5.75 5.50 5.75
2 1/2 9.62 7.50 1 1/8 8 1 6.25 6.00 6.25
3 9.50 7.50 1 8 7/8 5.75 5.50 5.75
4 11.50 9.25 1 1/4 8 1 1/8 6.75 6.50 6.75
5 13.75 11.00 1 3/8 8 1 1/4 7.50 7.25 7.50
6 15.00 12.50 1 1/4 12 1 1/8 7.50 7.25 7.75
8 18.50 15.50 1 1/2 12 1 3/8 8.75 8.50 8.75
10 21.50 18.50 1 1/2 16 1 3/8 9.25 9.00 9.25
FLANGES
12 24.00 21.00 1 1/2 20 1 3/8 10.00 9.75 10.00

14 25.25 22.00 1 5/8 20 1 1/2 10.75 10.50 11.00
16 27.75 24.25 1 3/4 20 1 5/8 11.25 11.00 11.50
18 31.00 27.00 2 20 1 7/8 12.75 12.50 13.25
20 33.75 29.50 2 1/8 20 2 13.75 13.50 14.25
24 41.00 35.50 2 5/8 20 2 1/2 17.25 17.00 18.00
30 48.50 42.75 3 1/8 20 3
bolt lengths (P)
42 61.50 54.75 3 5/8 24 3 1/2 see page 159.
48 70.25 62.50 4 1/8 24 4
30 46.50 40.75 3 1/8 20 3
36 53.00 47.25 3 1/8 24 3 Formula for determining
bolt lengths (P)
42 see page 159.
48
NOTES
92

TEL: 708/594-1700
FAX: 708/458-0106

Outside Thickness Diameter Diameter Threaded, Thread Slip-on Weld Lap Counter Depth
Diameter of of Lap
Pipe of Slip-on Lap Weld Length & Socket Neck & Joint Bore of
of Flange Weld Joint
Size Hub* & Socket Joint Neck (Min.) Weld Socket Radius Threaded Socket
Flange (Min.) Neck (Min.)
O.D. C W K Y2 Y3 Y1 T B2 B3 B1 J Z D
ASME B16.5
1/2 4.75 0.88 1.50 0.84 1.25 1.25 2.38 0.88 0.88 0.90 0.12 0.93 0.38
3/4 5.12 1.00 1.75 1.05 1.38 1.38 2.75 1.00 1.09 1.11 0.12 1.14 0.44
1 5.88 1.12 2.06 1.32 1.62 1.62 2.88 1.12 1.36 1.38 0.12 1.41 0.50
1 1/4 6.25 1.12 2.50 1.66 1.62 1.62 2.88 1.19 1.70 1.72 0.19 1.75 0.56
1 1/2 7.00 1.25 2.75 1.90 1.75 1.75 3.25 1.25 1.95 1.97 0.25 1.99 0.62
2 8.50 1.50 4.12 2.38 2.25 2.25 4.00 1.50 2.44 2.46 0.31 2.50 0.69
To be specified by the purchaser.

2 1/2 9.62 1.62 4.88 2.88 2.50 2.50 4.12 1.88 2.94 2.97 0.31 3.00 0.75
3 9.50 1.50 5.00 3.50 2.12 2.12 4.00 1.62 3.57 3.60 0.38 3.63
4 11.50 1.75 6.25 4.50 2.75 2.75 4.50 1.88 4.57 4.60 0.44 4.63
5 13.75 2.00 7.50 5.56 3.12 3.12 5.00 2.12 5.66 5.69 0.44 5.69
6 15.00 2.19 9.25 6.63 3.38 3.38 5.50 2.25 6.72 6.75 0.50 6.75
8 18.50 2.50 11.75 8.63 4.00 4.50 6.38 2.50 8.72 8.75 0.50 8.75
10 21.50 2.75 14.50 10.75 4.25 5.00 7.25 2.81 10.88 10.92 0.50 10.88
12 24.00 3.12 16.50 12.75 4.62 5.62 7.88 3.00 12.88 12.92 0.50 12.94
FLANGES
14 25.25 3.38 17.75 14.00 5.12 6.12 8.38 3.25 14.14 14.18 0.50 14.19
16 27.75 3.50 20.00 16.00 5.25 6.50 8.50 3.38 16.16 16.19 0.50 16.19
18 31.00 4.00 22.25 18.00 6.00 7.50 9.00 3.50 18.18 18.20 0.50 18.19
20 33.75 4.25 24.50 20.00 6.25 8.25 9.75 3.62 20.20 20.25 0.50 20.19
24 41.00 5.50 29.50 24.00 8.00 10.50 11.50 4.00 24.25 24.25 0.50 24.19
30 48.50 5.88 7.18 35.00 30.00 12.25
36 57.50 6.75 8.44 41.88 36.00 14.25
42 61.50 8.12 9.12 46.31 42.00 14.62
48 70.25 9.19 10.38 52.88 48.00 16.50
30 46.50 6.12 6.93 33.50 30.00 11.38
36 53.00 6.81 7.94 40.00 36.00 12.81
42
48
NOTES
1. Standard flange facings on page 146. 7. Blind flanges may be produced with or without hubs.
2. All dimensions are in inches. 8. All flanges conform to ASTM A105/ASME SA105.
3. Calculated flange weights on page 102. 9. All flanges 1/2"-24" conform to ASME B16.5.
4. For dimensional tolerances see page 144. All flanges 30" and larger conform to ASME B16.47.
5. Weld end preparations on page 154. * A taper shall not exceed 7 degrees on threaded, slip-on, and lapped flanges.
6. Thread standards on page 156.
93


Outside Diameter
O.D. M P P P
ASME B16.5
1/2 4.75 3.25 7/8 4 3/4 4.25 4.00 4.25
3/4 5.12 3.50 7/8 4 3/4 4.50 4.25 4.50
1 5.88 4.00 1 4 7/8 5.00 4.75 5.00
1 1/4 6.25 4.38 1 4 7/8 5.00 4.75 5.00
1 1/2 7.00 4.88 1 1/8 4 1 5.50 5.25 5.50
2 8.50 6.50 1 8 7/8 5.75 5.50 5.75
2 1/2 9.62 7.50 1 1/8 8 1 6.25 6.00 6.25
3 10.50 8.00 1 1/4 8 1 1/8 7.00 6.75 7.00
4 12.25 9.50 1 3/8 8 1 1/4 7.75 7.50 7.75
5 14.75 11.50 1 5/8 8 1 1/2 9.75 9.50 9.75
6 15.50 12.50 1 1/2 12 1 3/8 10.25 10.00 10.50
8 19.00 15.50 1 3/4 12 1 5/8 11.50 11.25 11.75
10 23.00 19.00 2 12 1 7/8 13.25 13.00 13.50
FLANGES
12 26.50 22.50 2 1/8 16 2 14.75 14.50 15.25

14 29.50 25.00 2 3/8 16 2 1/4 16.00 15.75 16.75
16 32.50 27.75 2 5/8 16 2 1/2 17.50 17.25 18.50
18 36.00 30.50 2 7/8 16 2 3/4 19.50 19.25 20.75
20 38.75 32.75 3 1/8 16 3 21.25 21.00 22.25
24 46.00 39.00 3 5/8 16 3 1/2 24.25 24.00 25.50
NOTES
1. Standard flange facings on page 146.
3. Calculated flange weights on page 103.
5. All flanges conform to ASTM A105/ASME SA105.
6. All flanges 1/2"-24" conform to ASME B16.5.
94

TEL: 708/594-1700
FAX: 708/458-0106

Outside Thickness Diameter Diameter
Threaded, Thread Slip-on Weld Counter Depth
Diameter of of Lap Joint
Pipe of Slip-on Lap Weld Length & Socket Lap Joint Neck & Bore of
of Flange Weld Radius Threaded
Size Hub* & Socket Joint Neck (Min.) Weld (Min.) Socket Socket
Flange (Min.) Neck
O.D. C W K Y2 Y3 Y1 T B2 B3 B1 J Z D
ASME B16.5
1/2 4.75 0.88 1.50 0.84 1.25 1.25 2.38 0.88 0.88 0.90 0.12 0.93 0.38
3/4 5.12 1.00 1.75 1.05 1.38 1.38 2.75 1.00 1.09 1.11 0.12 1.14 0.44
1 5.88 1.12 2.06 1.32 1.62 1.62 2.88 1.12 1.36 1.38 0.12 1.41 0.50
1 1/4 6.25 1.12 2.50 1.66 1.62 1.62 2.88 1.19 1.70 1.72 0.19 1.75 0.56
1 1/2 7.00 1.25 2.75 1.90 1.75 1.75 3.25 1.25 1.95 1.97 0.25 1.99 0.62
2 8.50 1.50 4.12 2.38 2.25 2.25 4.00 1.50 2.44 2.46 0.31 2.50 0.69

2 1/2 9.62 1.62 4.88 2.88 2.50 2.50 4.12 1.88 2.94 2.97 0.31 3.00 0.75
3 10.50 1.88 5.25 3.50 2.88 4.62 3.60 0.38
4 12.25 2.12 6.38 4.50 3.56 4.88 4.60 0.44
5 14.75 2.88 7.75 5.56 4.12 6.12 5.69 0.44
6 15.50 3.25 9.00 6.63 4.69 6.75 6.75 0.50
8 19.00 3.62 11.50 8.63 5.62 8.38 8.75 0.50
10 23.00 4.25 14.50 10.75 7.00 10.00 10.92 0.50
12 26.50 4.88 17.75 12.75 8.62 11.12 12.92 0.50
FLANGES
14 29.50 5.25 19.50 14.00 9.50 11.75 14.18 0.50
16 32.50 5.75 21.75 16.00 10.25 12.25 16.19 0.50
18 36.00 6.38 23.50 18.00 10.88 12.88 18.20 0.50
20 38.75 7.00 25.25 20.00 11.50 14.00 20.25 0.50
24 46.00 8.00 30.00 24.00 13.00 16.00 24.25 0.50
NOTES
4. For dimensional tolerances see page 144. * A taper shall not exceed 7 degrees on threaded, slip-on and lapped flanges.
5. Weld end preparations on page 154.
95


Outside Diameter
O.D. M P P P
ASME B16.5
1/2 5.25 3.50 7/8 4 3/4 4.75 4.50 4.75
3/4 5.50 3.75 7/8 4 3/4 5.00 4.75 5.00
1 6.25 4.25 1 4 7/8 5.50 5.25 5.50
1 1/4 7.25 5.12 1 1/8 4 1 6.00 5.75 6.00
1 1/2 8.00 5.75 1 1/4 4 1 1/8 6.75 6.50 6.75
2 9.25 6.75 1 1/8 8 1 7.00 6.75 7.00
2 1/2 10.50 7.75 1 1/4 8 1 1/8 7.75 7.50 8.00
3 12.00 9.00 1 3/8 8 1 1/4 8.75 8.50 9.00
4 14.00 10.75 1 5/8 8 1 1/2 10.00 9.75 10.25
5 16.50 12.75 1 7/8 8 1 3/4 11.75 11.50 12.25
6 19.00 14.50 2 1/8 8 2 13.50 13.25 14.00
8 21.75 17.25 2 1/8 12 2 15.00 14.75 15.50
10 26.50 21.25 2 5/8 12 2 1/2 19.25 19.00 20.00
FLANGES
12 30.00 24.38 2 7/8 12 2 3/4 21.25 21.00 22.00

NOTES
1. Standard flange facings on page 146.
3. Calculated flange weights on page 104.
5. All flanges conform to ASTM A105/ASME SA105.
6. All flanges 1/2"-12" conform to ASME B16.5.
96

TEL: 708/594-1700
FAX: 708/458-0106

Outside Thickness Diameter
Diameter Thread Counter
Diameter of of Lap Joint
Pipe of Lap Weld Length Lap Joint Weld Bore
of Flange Weld Threaded Radius
Size Hub* Joint Neck (Min.) (Min.) Neck Threaded
Flange (Min.) Neck Flange
O.D. C W K Y2 Y3 Y1 T B3 B1 J Z
ASME B16.5
1/2 5.25 1.19 1.69 0.84 1.56 1.56 2.88 1.12 0.90 0.12 0.93
3/4 5.50 1.25 2.00 1.05 1.69 1.69 3.12 1.25 1.11 0.12 1.14
1 6.25 1.38 2.25 1.32 1.88 1.88 3.50 1.38 1.38 0.12 1.41

1 1/4 7.25 1.50 2.88 1.66 2.06 2.06 3.75 1.50 1.72 0.19 1.75
1 1/2 8.00 1.75 3.12 1.90 2.38 2.38 4.38 1.75 1.97 0.25 1.99
2 9.25 2.00 3.75 2.38 2.75 2.75 5.00 2.00 2.46 0.31 2.50
2 1/2 10.50 2.25 4.50 2.88 3.12 3.12 5.62 2.25 2.97 0.31 3.00
3 12.00 2.62 5.25 3.50 3.62 6.62 3.60 0.38
4 14.00 3.00 6.50 4.50 4.25 7.50 4.60 0.44
5 16.50 3.62 8.00 5.56 5.12 9.00 5.69 0.44
6 19.00 4.25 9.25 6.63 6.00 10.75 6.75 0.50
8 21.75 5.00 12.00 8.63 7.00 12.50 8.75 0.50
10 26.50 6.50 14.75 10.75 9.00 16.50 10.92 0.50
12 30.00 7.25 17.38 12.75 10.00 18.25 12.92 0.50
FLANGES
NOTES
4. For dimensional tolerances see page 144. * A taper shall not exceed 7 degrees on threaded, slip-on and lapped flanges.
5. Weld end preparations on page 154.
97

reducing Slip-on AND threaded flanges — ALL Classes
Note:
Pipe Smallest Size of Reducing Outlet
Size Requiring Hub Flanges
1. The hub dimensions shall be at least as large as
1 1/2
those of the standard flanges of the size to which
1 1/4 1/2 the reduction is being made, except flanges reducing
FLANGES
1 1/2 1/2 to a size smaller than those Groups I, II and III may
Group I
2 1 be made from blind flanges.
2 1/2 1 1/4
3 1 1/4 2. Class 150 flanges do not have a counter bore.
3 1/2 1 1/2 Class 300 and higher pressure flanges will have depth
4 1 1/2 of counter bore (q) of 0.25 in. for NPS 2 and smaller
5 1 1/2 tapping and 0.38 in. for NPS 2 1/2" and larger. The
Group II diameter (Q) of counter bore is the same as that
6 2 1/2
given in the tables of threaded flanges for the
8 3 corresponding tapping.
10 3 1/2
12 3 1/2 3. Minimum length of effective threads shall be at least
14 3 1/2 equal to dimension (T) of the corresponding pressure
16 4 class threaded flange as shown in tables, but do not
Group III necessarily extend to the face of the flange. For thread
18 4
20 4 of threaded flanges, see page 158.
24 4
98

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com calculated flange weights
CLASS 150
Outside
Pipe Diameter Threaded Weld Neck Blind Lap Joint
Size & Slip-on
O.D.
ASME B16.5
1/2 3.50 2.00 2.00 2.00 1.00
3/4 3.88 2.00 2.00 2.00 2.00
1 4.25 2.00 3.00 2.00 2.00
1 1/4 4.62 3.00 3.00 3.00 3.00
1 1/2 5.00 3.00 4.00 4.00 3.00
2 6.00 5.00 6.00 5.00 5.00
2 1/2 7.00 8.00 10.00 7.00 8.00
3 7.50 9.00 11.50 9.00 9.00
3 1/2 8.50 12.00 12.00 13.00 11.00
4 9.00 13.00 16.50 17.00 13.00
5 10.00 15.00 21.00 20.00 15.00
6 11.00 19.00 26.00 27.00 19.00
8 13.50 30.00 42.00 47.00 30.00
10 16.00 43.00 54.00 70.00 43.00
12 19.00 64.00 88.00 123.00 64.00
14 21.00 90.00 114.00 140.00 105.00
16 23.50 106.00 140.00 180.00 140.00
18 25.00 130.00 165.00 220.00 160.00
20 27.50 165.00 197.00 285.00 195.00
24 32.00 220.00 268.00 430.00 275.00
FLANGES
30 38.75 — 400.00 982.00 —
36 46.00 — 640.00 1676.00 —
42 53.00 — 890.00 2381.00 —
48 59.50 — 1185.00 3348.00 —
30 34.94 — 150.00 543.00 —
36 41.62 — 240.00 890.00 —
42 48.25 — 345.00 1393.00 —
48 54.81 — 480.00 2045.00 —
NOTES
2. All weights are in pounds and approximated or estimated.
99

calculated flange weights
CLASS 300
Outside
Size & Slip-on
O.D.
ASME B16.5
1/2 3.75 3.00 2.00 2.00 2.00
3/4 4.62 3.00 3.00 3.00 3.00
1 4.88 3.00 4.00 4.00 3.00
1 1/4 5.25 4.50 5.00 6.00 4.50
1 1/2 6.12 6.50 7.00 7.00 6.50
2 6.50 7.00 9.00 8.00 7.00
2 1/2 7.50 10.00 12.00 12.00 10.00
3 8.25 14.00 18.00 16.00 14.00
3 1/2 9.00 17.00 20.00 21.00 17.00
4 10.00 24.00 26.50 28.00 24.00
5 11.00 31.00 36.00 37.00 28.00
6 12.50 39.00 45.00 50.00 39.00
8 15.00 58.00 69.00 81.00 58.00
10 17.50 81.00 100.00 124.00 91.00
12 20.50 115.00 142.00 185.00 140.00
14 23.00 165.00 206.00 250.00 190.00
16 25.50 220.00 250.00 315.00 234.00
18 28.00 280.00 320.00 415.00 305.00
20 30.50 325.00 400.00 515.00 375.00
24 36.00 490.00 580.00 800.00 550.00
FLANGES
30 43.00 — 870.00 1543.00 —

36 50.00 — 1275.00 2436.00 —
42 50.75 — 950.00 2688.00 —
48 57.75 — 1380.00 3896.00 —
30 39.00 — 550.00 1249.00 —
36 46.12 — 840.00 1921.00 —
42 52.50 — 1135.00 2876.00 —
48 59.50 — 1575.00 4183.00 —
NOTES
100

TEL: 708/594-1700
FAX: 708/458-0106
CLASS 600
Outside
Size & Slip-on
O.D.
ASME B16.5
1/2 3.75 2.00 3.00 3.00 2.00
3/4 4.62 3.00 4.00 4.00 3.00
1 4.88 4.00 4.00 4.00 4.00
1 1/4 5.25 5.00 6.00 6.00 5.00
1 1/2 6.12 7.00 8.00 8.00 7.00
2 6.50 9.00 12.00 10.00 9.00
2 1/2 7.50 13.00 18.00 15.00 12.00
3 8.25 16.00 23.00 20.00 15.00
3 1/2 9.00 21.00 26.00 29.00 20.00
4 10.75 37.00 42.00 41.00 36.00
5 13.00 63.00 68.00 68.00 63.00
6 14.00 80.00 81.00 86.00 78.00
8 16.50 115.00 120.00 140.00 112.00
10 20.00 177.00 190.00 231.00 195.00
12 22.00 215.00 226.00 295.00 240.00
14 23.75 259.00 347.00 378.00 290.00
16 27.00 366.00 481.00 527.00 400.00
18 29.25 476.00 555.00 665.00 469.00
20 32.00 612.00 690.00 855.00 604.00
24 37.00 876.00 977.00 1250.00 866.00
FLANGES
30 44.50 — 1210.00 2423.00 —
36 51.75 — 1705.00 3802.00 —
42 55.25 — 2030.00 4585.00 —
48 62.75 — 2855.00 6737.00 —
30 40.25 — 810.00 1802.00 —
36 47.75 — 1340.00 3013.00 —
NOTES
101

CLASS 900
Outside
Size & Slip-on
O.D.
ASME B16.5
1/2 4.75 6.00 7.00 4.00 6.00
3/4 5.12 6.00 7.00 6.00 6.00
1 5.88 7.50 8.50 9.00 7.50
1 1/4 6.25 10.00 10.00 10.00 10.00
1 1/2 7.00 14.00 14.00 14.00 14.00
2 8.50 22.00 24.00 25.00 21.00
2 1/2 9.62 31.00 31.00 32.00 25.00
3 9.50 36.00 36.00 35.00 29.00
4 11.50 53.00 53.00 54.00 51.00
5 13.75 83.00 86.00 87.00 81.00
6 15.00 110.00 110.00 115.00 105.00
8 18.50 172.00 187.00 200.00 190.00
10 21.50 245.00 268.00 290.00 277.00
12 24.00 326.00 372.00 415.00 371.00
14 25.25 400.00 562.00 520.00 415.00
16 27.75 459.00 685.00 619.00 488.00
18 31.00 647.00 924.00 880.00 670.00
20 33.75 792.00 1164.00 1107.00 868.00
24 41.00 1480.00 2107.00 2099.00 1659.00
30 48.50 — 2120.00 3758.00 —
FLANGES
36 57.50 — 3395.00 6209.00 —

42 61.50 — 3960.00 7675.00 —
48 70.25 — 4980.00 11398.00 —
30 46.50 — 1820.00 3334.00 —
36 53.00 — 2520.00 4963.00 —
NOTES
102

TEL: 708/594-1700
FAX: 708/458-0106
CLASS 1500
Outside
Size & Slip-on
O.D.
ASME B16.5
1/2 4.75 6.00 7.00 4.00 6.00
3/4 5.12 6.00 7.00 6.00 6.00
1 5.88 8.00 9.00 9.00 8.00
1 1/4 6.25 10.00 10.00 10.00 10.00
1 1/2 7.00 14.00 14.00 14.00 14.00
2 8.50 25.00 25.00 25.00 25.00
2 1/2 9.62 36.00 36.00 35.00 35.00
3 10.50 48.00 48.00 48.00 47.00
4 12.25 73.00 73.00 73.00 75.00
5 14.75 132.00 132.00 140.00 140.00
6 15.50 165.00 165.00 160.00 170.00
8 19.00 260.00 275.00 302.00 286.00
10 23.00 436.00 455.00 510.00 485.00
12 26.50 667.00 690.00 775.00 749.00
14 29.50 940.00 940.00 975.00 890.00
16 32.50 1250.00 1250.00 1300.00 1250.00
18 36.00 1625.00 1625.00 1750.00 1475.00
20 38.75 2050.00 2050.00 2225.00 1775.00
24 46.00 2825.00 3325.00 3625.00 2825.00
NOTES
FLANGES
103

CLASS 2500
Outside
Size & Slip-on
O.D.
ASME B16.5
1/2 5.25 7.00 8.00 7.00 7.00
3/4 5.50 9.00 9.00 10.00 8.00
1 6.25 12.00 13.00 12.00 12.00
1 1/4 7.25 18.00 20.00 18.00 17.00
1 1/2 8.00 25.00 28.00 25.00 24.00
2 9.25 38.00 42.00 39.00 37.00
2 1/2 10.50 55.00 52.00 56.00 53.00
3 12.00 83.00 94.00 86.00 80.00
4 14.00 127.00 146.00 133.00 122.00
5 16.50 210.00 244.00 223.00 204.00
6 19.00 323.00 378.00 345.00 314.00
8 21.75 485.00 576.00 533.00 471.00
10 26.50 925.00 1068.00 1025.00 897.00
12 30.00 1300.00 1608.00 1464.00 1262.00
NOTES
FLANGES
104

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com flange packaging
BOX QUANTITIES
SLIP-ON, THREADED, LAP JOINT, SOCKET WELD (STD & XS), BLINDS
Box
Quantities Class 150 Class 300 Class 600 Class 900 Class 1500 Class 2500
Nominal (Raised & Flat Face) (Raised & Flat Face) (Raised & Flat Face) (Raised & Flat Face) (Raised & Flat Face) (Raised & Flat Face)
Pipe Size
1/2" 12 6 6 — — —
3/4" 12 6 6 — — —
1" 12 6 6 — — —
1 1/4" 12 6 6 — — —
1 1/2" 12 6 6 — — —
BOX QUANTITIES
WELD-NECK (STD & XS)
Box
Pipe Size
1/2" 12 6 6 — — —
3/4" 12 6 6 — — —
1" 12 6 6 — — —
1 1/4" 12 6 6 — — —
1 1/2" 12 6 6 — — —
BUNDLE QUANTITIES
SLIP-ON, THREADED, LAP JOINT, SOCKET WELD (STD & XS)
Bundle
Pipe Size
2" 20 16 — — — —
2 1/2" 18 14 — — — —
FLANGES
3" 17 12 — — — —
3 1/2" 15 — — — — —
4" 15 11 — — — —
5" 14 11 — — — —
6" 13 10 — — — —
8" 12 8 — — — —
10" 11 — — — — —
12" 9 — — — — —
BUNDLE QUANTITIES
WELD-NECK (STD & XS)
Bundle
Pipe Size
2" 9 8 — — — —
2 1/2" 8 8 — — — —
3" 8 8 — — — —
3 1/2" 8 8 — — — —
4" 8 7 — — — —
5" 7 6 — — — —
6" 7 6 — — — —
8" 6 5 — — — —
10" 6 — — — — —
105
12" — — — — — —
TECHNICAL DATA INDEX
PAGE
Bevel Detail-Welding Fittings .................................................................................................................................... 107

Buttweld Fittings Tolerances .................................................................................................................................. 108
Buttweld Fittings Pressure-Temperature Ratings B31.1 [Schedule: STD, XS, 40, 80, 160, XXS]..... 109
Buttweld Fittings Pressure Ratings WPB B31.8 [Schedule: STD, XS, 40, 80, 160, XXS] ................ 114
Buttweld Fittings Pressure Ratings WPHY-52 B31.8 [Schedule: STD, XS, 40, 80, 160, XXS]....... 119
Buttweld Fittings Pressure Ratings WPHY-65 B31.8 [Schedule: STD, XS, 40, 80, 160, XXS]....... 124
Flow Resistance For Fittings ...................................................................................................................................... 129
Flexibility and Stress Intensification Factors .............................................................................................. 131
Thermal Expansion For Carbon Steel Pipe ......................................................................................................... 132
Dimensions of Welding Ends [Schedule: STD, XS, 40, 80, 160, XXS] ......................................................... 133
Dimensions of Steel Pipe ................................................................................................................................................. 138
Dimensional Tolerances For Flanges .................................................................................................................. 144
Gasket Surface Finishes .................................................................................................................................................. 145
Standard Flange Facings .............................................................................................................................................. 146
Ring Type Joint Facing Dimensions [Class: 150, 300, 600, 900, 1500, 2500] ........................................... 148
Weld End preparations .................................................................................................................................................... 154
Thread Standard Practices ......................................................................................................................................... 156
Thread Standards .............................................................................................................................................................. 158
Method For Calculating Bolt Lengths ............................................................................................................... 159
Pressure-Temperature Ratings For Flanges ................................................................................................... 161
Useful Formulas .................................................................................................................................................................. 162
Conversion Chart ............................................................................................................................................................... 165
Metric System Conversions .......................................................................................................................................... 166
Material Test Report Identification ...................................................................................................................... 168
Torque Required to Produce Indicated Bolt Stress .................................................................................. 170
Bolt Torque Procedure ................................................................................................................................................... 172
Material Safety Data ........................................................................................................................................................ 175
106

TEL: 708/894-1700
FAX: 708/458-0106
www.weldbend.com bevel Detail — welding fittings
PLAIN BEVEL
Figure 1
37 ½° ± 2 ½°
Note
(1)
0.88" max.
D
Note 0.06" ± 0.03"

(1) (Root face)
COMPOUND BEVEL
Figure 2
Note
(1) 10° ± 2 ½°
Rad.
0.88"
D
37 ½° ± 2 ½°
0.75"
Note 0.06" ± 0.03"

(1) (Root face)
TECHNICAL DATA
Wall Thickness (T) End Preparation

Less than x [2] Cut square or slightly chamfer, at manufacturer's option (not illustrated).
x to 0.88, inclusive Plain bevel as in Figure 1 above.
More than 0.88 Compound bevel as in Figure 2 above.
Note:
1. See ASME B16.9 for transition contours.
2. x = 0.19" for carbon steel or ferritic alloy steel and 0.12" for austenitic alloy steel. 107

buttweld fittings tolerances
90° Reducers
3R 90° and and Lap
and
Weldbend Fittings 45° Joint Caps 180° Return Bends Stub Ends
3R 45° Elbows Stub
Elbows and Tees Ends
Outside
Outside Inside Center Center Overall Overall Center Back Thickness Radius
Pipe Diameter Diameter to End to End Length Length to Center to Face Alignment Diameter of Lap of Lap
of Ends of Lap
Size
O.D. I.D. C, A C, A, B, R L, J H V W K T N
+0.06, + 0, + 0, + 0.06,
1/2 to 2 1/2 0.03 0.09 0.06 0.06 0.12 0.25 0.25 0.03
– 0.03 – 0.03 – 0.03 –0
+ 0, + 0, + 0.06,
3 to 3 1/2 0.06 0.06 0.09 0.06 0.06 0.12 0.25 0.25 0.03
– 0.03 – 0.06 –0
+ 0, + 0, + 0.06,
4 0.06 0.06 0.09 0.06 0.06 0.12 0.25 0.25 0.03
– 0.03 – 0.06 –0
+0.09, + 0, + 0, + 0.06,
5 to 8 0.06 0.09 0.06 0.06 0.25 0.25 0.25 0.03
– 0.06 – 0.03 – 0.06 –0
+0.16, + 0, + 0, + 0.12,
10 to 18 0.12 0.12 0.09 0.09 0.25 0.38 0.25 0.06
– 0.12 – 0.06 – 0.06 –0
+0.25, + 0, + 0, + 0.12,
20 to 24 0.19 0.12 0.09 0.09 0.25 0.38 0.25 0.06
– 0.19 – 0.06 – 0.06 –0
+0.25,
26 to 30 0.19 0.25 0.12 0.19 0.38
– 0.19
+0.25,
30 to 48 0.19 0.38 0.19 0.19 0.38
– 0.19
NOTES
2. Tolerances are equal plus and minus unless indicated.
3. The inside diameter and nominal wall thickness at ends
are to be specified by purchaser.
4. Please refer to ASME B16.9 for further information
regarding tolerances.
5. Minimum wall thickness of 87.5% applies.
6. The out-of-round is the sum of the absolute values of
the plus and minus tolerances.
Pipe Off Off

Size Angle Plane
½–4 0.03 0.06
5–8 0.06 0.12
10 – 12 0.09 0.19
14 – 16 0.09 0.25
TECHNICAL DATA
18 – 24 0.12 0.38
26 – 30 0.19 0.38
32 – 42 0.19 0.50
44 – 48 0.19 0.75
108

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com buttweld fittings pressure-temperature ratings
Based on Code For Pressure Piping B31.1
SCHEDULE STD
For reference only
Wall Thickness
Pipe Working Pressure – Lbs per Square Inch at the Fahrenheit Temperature Indicated**
Inches*
Size
T -20° to 650° 700° 750° 800°***
1/2 0.109 4989 4551 3793 3151
3/4 0.113 4065 3709 3091 2568
1 0.133 3800 3467 2889 2400
1 1/4 0.140 3124 2850 2375 1973
1 1/2 0.145 2806 2560 2134 1773
2 0.154 2360 2153 1794 1491
2 1/2 0.203 2583 2357 1964 1632
3 0.216 2240 2043 1703 1415
3 1/2 0.226 2041 1862 1551 1289
4 0.237 1895 1729 1441 1197
5 0.258 1659 1514 1261 1048
6 0.280 1506 1374 1145 951
8 0.322 1324 1208 1007 836
10 0.365 1201 1095 913 758
12 0.375 1035 945 787 654
14 0.375 941 858 715 594
16 0.375 820 748 624 518
18 0.375 727 664 553 459
20 0.375 653 596 497 413
24 0.375 543 495 413 343
30 0.375 433 395 329 273
36 0.375 360 328 274 227
42 0.375 308 281 234 195
48 0.375 269 246 205 170
Please review B31.1 for formula information.
NOTES
2. All values listed in table above to be considered as a guide only.
Please refer to B31.1 for formula and other factors that could
effect the determination of pressure ratings.
* Nominal wall thickness; they correspond respectively to the
thickness of Schedule STANDARD WALL GRADE B steel pipe.
TECHNICAL DATA
** Ratings apply in accordance with Sections 1 and 5 of the Code

for Pressure Pipe. The values shown are based upon a corrosion
allowance of 0 inches.
*** Upon prolonged exposure to temperatures about 775° the
carbide phase of carbon steel may be converted to graphite.
For other applications refer to appropriate section of B31 Code
for Pressure Piping.
109

buttweld fittings pressure-temperature ratings
SCHEDULE XS
For reference only
Wall Thickness
Inches*
Size
T -20° to 650° 700° 750° 800°***
1/2 0.147 6942 6333 5278 4385
3/4 0.154 5709 5209 4341 3606
1 0.179 5258 4797 3998 3321
1 1/4 0.191 4373 3989 3324 2762
1 1/2 0.200 3969 3620 3017 2506
2 0.218 3422 3121 2601 2161
2 1/2 0.276 3591 3276 2730 2268
3 0.300 3178 2900 2416 2007
3 1/2 0.318 2932 2675 2229 1852
4 0.337 2751 2509 2091 1737
5 0.375 2459 2243 1870 1553
6 0.432 2374 2166 1805 1499
8 0.500 2097 1913 1594 1324
10 0.500 1664 1518 1265 1051
12 0.500 1394 1271 1059 880
14 0.500 1265 1154 962 799
16 0.500 1102 1005 838 696
18 0.500 976 891 742 617
20 0.500 876 799 666 553
24 0.500 727 664 553 459
30 0.500 579 529 441 366
36 0.500 482 439 366 304
42 0.500 412 376 313 260
48 0.500 360 328 274 227
NOTES
thickness of Schedule EXTRA-STRONG WALL GRADE B steel pipe.
TECHNICAL DATA

110

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE 40
For reference only
Wall Thickness
Inches*
Size
T -20° to 650° 700° 750° 800°***
12 0.406 1124 1025 854 710
14 0.438 1103 1007 839 697
16 0.500 1102 1005 838 696
18 0.562 1101 1004 837 695
20 0.594 1046 954 795 661
24 0.688 1008 920 767 637

SCHEDULE 80
For reference only
Wall Thickness
Inches*
Size
T -20° to 650° 700° 750° 800°***
10 0.594 1993 1819 1515 1259
12 0.688 1944 1774 1478 1228
14 0.750 1930 1760 1467 1219
16 0.844 1899 1732 1443 1199
18 0.938 1875 1710 1425 1184
20 1.031 1853 1691 1409 1171
24 1.219 1825 1665 1387 1153
NOTES
TECHNICAL DATA

thickness of SCHEDULE 40 and SCHEDULE 80 WALL GRADE B steel pipe.
111

buttweld fittings pressure-temperature ratings
SCHEDULE 160
For reference only
Wall Thickness
Inches*
Size
T -20° to 650° 700° 750° 800°***
1/2 0.188 9104 8306 6921 5750
3/4 0.219 8428 7688 6407 5323
1 0.250 7609 6941 5785 4806
1 1/4 0.250 5879 5363 4469 3713
1 1/2 0.281 5762 5257 4381 3639
2 0.344 5631 5137 4281 3556
2 1/2 0.375 5017 4577 3814 3169
3 0.438 4794 4373 3645 3028
4 0.531 4495 4101 3417 2839
5 0.625 4260 3887 3239 2691
6 0.719 4103 3743 3119 2591
8 0.906 3960 3612 3010 2501
10 1.125 3944 3598 2998 2491
12 1.312 3872 3532 2944 2445
14 1.406 3771 3440 2867 2382
16 1.594 3738 3410 2842 2361
18 1.781 3711 3385 2821 2344
20 1.969 3691 3367 2806 2331
24 2.344 3659 3338 2782 2311
NOTES
thickness of SCHEDULE 160 WALL GRADE B steel pipe.
TECHNICAL DATA
112

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE XXS
For reference only
Wall Thickness
Inches*
Size
T -20° to 650° 700° 750° 800°***
1/2 0.294 14276 13024 10853 9017
3/4 0.308 12110 11047 9206 7648
1 0.358 11223 10239 8532 7088
1 1/4 0.382 9384 8561 7134 5927
1 1/2 0.400 8515 7768 6473 5378
2 0.436 7320 6678 5565 4623
2 1/2 0.552 7692 7018 5848 4858
3 0.600 6785 6190 5158 4286
4 0.674 5843 5331 4442 3691
5 0.750 5203 4747 3955 3286
6 0.864 5016 4576 3814 3168
8 0.875 3813 3478 2899 2408
10 1.000 3471 3167 2639 2192
12 1.000 2890 2636 2197 1825
NOTES
thickness of SCHEDULE Double Extra-Strong WALL GRADE B steel pipe.
TECHNICAL DATA
113

buttweld fittings pressure ratings
Based on the Code for Pressure Piping B31.8
SCHEDULE STD
For reference only
Nominal Wall 35,000 psi Yield Strength

Thickness
Outside Inches
Pipe Basic Design Factor
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.109 3633 4542 5450 6540
3/4 1.050 0.113 3013 3767 4520 5424
1 1.315 0.133 2832 3540 4248 5097
1 1/4 1.660 0.140 2361 2952 3542 4251
1 1/2 1.900 0.145 2137 2671 3205 3846
2 2.375 0.154 1816 2269 2723 3268
2 1/2 2.875 0.203 1977 2471 2966 3559
3 3.500 0.216 1728 2160 2592 3110
3 1/2 4.000 0.226 1582 1978 2373 2848
4 4.500 0.237 1475 1843 2212 2654
5 5.563 0.258 1299 1623 1948 2337
6 6.625 0.280 1183 1479 1775 2130
8 8.625 0.322 1045 1307 1568 1882
10 10.750 0.365 951 1188 1426 1711
12 12.750 0.375 824 1029 1235 1482
14 14.000 0.375 750 938 1125 1350
16 16.000 0.375 656 820 984 1181
18 18.000 0.375 583 729 875 1050
20 20.000 0.375 525 656 788 945
24 24.000 0.375 438 547 656 788
30 30.000 0.375 350 438 525 630
36 36.000 0.375 292 365 438 525
42 42.000 0.375 250 313 375 450
48 48.000 0.375 219 273 328 394
NOTES
TECHNICAL DATA

3. A joint sufficiency factor of 1.00 is assumed.
4. Ratings are for a temperature of 250°F or less.
114 WPB
TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com buttweld fittings pressure ratings
SCHEDULE XS
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.147 4900 6125 7350 8820
3/4 1.050 0.154 4107 5133 6160 7392
1 1.315 0.179 3811 4764 5717 6861
1 1/4 1.660 0.191 3222 4027 4833 5799
1 1/2 1.900 0.200 2947 3684 4421 5305
2 2.375 0.218 2570 3213 3855 4626
2 1/2 2.875 0.276 2688 3360 4032 4838
3 3.500 0.300 2400 3000 3600 4320
3 1/2 4.000 0.318 2226 2783 3339 4007
4 4.500 0.337 2097 2621 3145 3774
5 5.563 0.375 1887 2359 2831 3397
6 6.625 0.432 1826 2282 2739 3286
8 8.625 0.500 1623 2029 2435 2922
10 10.750 0.500 1302 1628 1953 2344
12 12.750 0.500 1098 1373 1647 1976
14 14.000 0.500 1000 1250 1500 1800
16 16.000 0.500 875 1094 1313 1575
18 18.000 0.500 778 972 1167 1400
20 20.000 0.500 700 875 1050 1260
24 24.000 0.500 583 729 875 1050
30 30.000 0.500 467 583 700 840
36 36.000 0.500 389 486 583 700
42 42.000 0.500 333 417 500 600
48 48.000 0.500 292 365 438 525
NOTES
TECHNICAL DATA

WPB
115
SCHEDULE 40
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
12 12.750 0.406 892 1115 1337 1605
14 14.000 0.438 876 1095 1314 1577
16 16.000 0.500 875 1094 1313 1575
18 18.000 0.562 874 1093 1311 1574
20 20.000 0.594 832 1040 1247 1497
24 24.000 0.688 803 1003 1204 1445
36 36.000 0.750 583 729 875 1050

SCHEDULE 80
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
10 10.750 0.594 1547 1934 2321 2785
12 12.750 0.688 1511 1889 2266 2720
14 14.000 0.750 1500 1875 2250 2700
16 16.000 0.844 1477 1846 2216 2659
18 18.000 0.938 1459 1824 2189 2626
20 20.000 1.031 1443 1804 2165 2598
24 24.000 1.219 1422 1778 2133 2560
TECHNICAL DATA

NOTES
WPB
116

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE 160
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.188 6267 7833 9400 11280
3/4 1.050 0.219 5840 7300 8760 10512
1 1.315 0.250 5323 6654 7985 9582
1 1/4 1.660 0.250 4217 5271 6325 7590
1 1/2 1.900 0.281 4141 5176 6212 7454
2 2.375 0.344 4056 5069 6083 7300
2 1/2 2.875 0.375 3652 4565 5478 6574
3 3.500 0.438 3504 4380 5256 6307
4 4.500 0.531 3304 4130 4956 5947
5 5.563 0.625 3146 3932 4719 5662
6 6.625 0.719 3039 3798 4558 5470
8 8.625 0.906 2941 3677 4412 5294
10 10.750 1.125 2930 3663 4395 5274
12 12.750 1.312 2881 3602 4322 5186
14 14.000 1.406 2812 3515 4218 5062
16 16.000 1.594 2790 3487 4184 5021
18 18.000 1.781 2770 3463 4156 4987
20 20.000 1.969 2757 3446 4135 4962
24 24.000 2.344 2735 3418 4102 4922
NOTES
TECHNICAL DATA
WPB
117
SCHEDULE XXS
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.294 9800 12250 14700 17640
3/4 1.050 0.308 8213 10267 12320 14784
1 1.315 0.358 7623 9529 11434 13721
1 1/4 1.660 0.382 6443 8054 9665 11598
1 1/2 1.900 0.400 5895 7368 8842 10611
2 2.375 0.436 5140 6425 7710 9252
2 1/2 2.875 0.552 5376 6720 8064 9677
3 3.500 0.600 4800 6000 7200 8640
4 4.500 0.674 4194 5242 6291 7549
5 5.563 0.750 3775 4719 5662 6795
6 6.625 0.864 3652 4565 5477 6573
8 8.625 0.875 2841 3551 4261 5113
10 10.750 1.000 2605 3256 3907 4688
12 12.750 1.000 2196 2745 3294 3953
NOTES
TECHNICAL DATA
118 WPB
TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE STD WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.109 5398 6748 8097 9717
3/4 1.050 0.113 4477 5596 6715 8059
1 1.315 0.133 4207 5259 6311 7573
1 1/4 1.660 0.140 3508 4386 5263 6315
1 1/2 1.900 0.145 3175 3968 4762 5715
2 2.375 0.154 2697 3372 4046 4855
2 1/2 2.875 0.203 2937 3672 4406 5287
3 3.500 0.216 2567 3209 3851 4621
3 1/2 4.000 0.226 2350 2938 3526 4231
4 4.500 0.237 2191 2739 3286 3944
5 5.563 0.258 1929 2412 2894 3473
6 6.625 0.280 1758 2198 2637 3165
8 8.625 0.322 1553 1941 2330 2796
10 10.750 0.365 1412 1766 2119 2542
12 12.750 0.375 1224 1529 1835 2202
14 14.000 0.375 1114 1393 1671 2006
16 16.000 0.375 975 1219 1463 1755
18 18.000 0.375 867 1083 1300 1560
20 20.000 0.375 780 975 1170 1404
24 24.000 0.375 650 813 975 1170
30 30.000 0.375 520 650 780 936
36 36.000 0.375 433 542 650 780
42 42.000 0.375 371 464 557 669
48 48.000 0.375 325 406 488 585
NOTES
TECHNICAL DATA

WPHY-52 Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

119
SCHEDULE XS WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.147 7280 9100 10920 13104
3/4 1.050 0.154 6101 7627 9152 10982
1 1.315 0.179 5663 7078 8494 10193
1 1/4 1.660 0.191 4787 5983 7180 8616
1 1/2 1.900 0.200 4379 5474 6568 7882
2 2.375 0.218 3818 4773 5728 6873
2 1/2 2.875 0.276 3994 4992 5990 7188
3 3.500 0.300 3566 4457 5349 6418
3 1/2 4.000 0.318 3307 4134 4961 5953
4 4.500 0.337 3115 3894 4673 5608
5 5.563 0.375 2804 3505 4206 5048
6 6.625 0.432 2713 3391 4069 4883
8 8.625 0.500 2412 3014 3617 4341
10 10.750 0.500 1935 2419 2902 3483
12 12.750 0.500 1631 2039 2447 2936
14 14.000 0.500 1486 1857 2229 2674
16 16.000 0.500 1300 1625 1950 2340
18 18.000 0.500 1156 1444 1733 2080
20 20.000 0.500 1040 1300 1560 1872
24 24.000 0.500 867 1083 1300 1560
30 30.000 0.500 693 867 1040 1248
36 36.000 0.500 578 722 867 1040
42 42.000 0.500 495 619 743 891
48 48.000 0.500 433 542 650 780
NOTES
TECHNICAL DATA

120 WPHY-52 Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE 40 WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
12 12.750 0.406 1325 1656 1987 2384
14 14.000 0.438 1301 1627 1952 2343
16 16.000 0.500 1300 1625 1950 2340
18 18.000 0.562 1299 1624 1948 2338
20 20.000 0.594 1236 1544 1853 2224
24 24.000 0.688 1193 1491 1789 2147
36 36.000 0.750 867 1083 1300 1560

SCHEDULE 80 WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
10 10.750 0.594 2299 2873 3448 4138
12 12.750 0.688 2245 2806 3367 4041
14 14.000 0.750 2229 2786 3343 4011
16 16.000 0.844 2194 2743 3292 3950
18 18.000 0.938 2168 2710 3252 3902
20 20.000 1.031 2144 2681 3217 3860
24 24.000 1.219 2113 2641 3169 3803
TECHNICAL DATA

NOTES
WPHY-52
121

SCHEDULE 160 WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.188 9310 11638 13966 16759
3/4 1.050 0.219 8677 10846 13015 15618
1 1.315 0.250 7909 9886 11863 14236
1 1/4 1.660 0.250 6265 7831 9398 11277
1 1/2 1.900 0.281 6152 7691 9229 11074
2 2.375 0.344 6025 7532 9038 10846
2 1/2 2.875 0.375 5426 6783 8139 9767
3 3.500 0.438 5206 6507 7809 9371
4 4.500 0.531 4909 6136 7363 8836
5 5.563 0.625 4674 5842 7011 8413
6 6.625 0.719 4515 5643 6772 8127
8 8.625 0.906 4370 5462 6555 7866
10 10.750 1.125 4353 5442 6530 7836
12 12.750 1.312 4281 5351 6421 7705
14 14.000 1.406 4178 5222 6267 7520
16 16.000 1.594 4144 5181 6217 7460
18 18.000 1.781 4116 5145 6174 7409
20 20.000 1.969 4096 5119 6143 7372
24 24.000 2.344 4063 5079 6094 7313
NOTES
TECHNICAL DATA

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE XXS WPHY-52
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.294 14560 18200 21840 26208
3/4 1.050 0.308 12203 15253 18304 21965
1 1.315 0.358 11325 14157 16988 20386
1 1/4 1.660 0.382 9573 11966 14360 17231
1 1/2 1.900 0.400 8758 10947 13137 15764
2 2.375 0.436 7637 9546 11455 13746
2 1/2 2.875 0.552 7987 9984 11981 14377
3 3.500 0.600 7131 8914 10697 12837
4 4.500 0.674 6231 7788 9346 11215
5 5.563 0.750 5608 7011 8413 10095
6 6.625 0.864 5425 6782 8138 9765
8 8.625 0.875 4220 5275 6330 7597
10 10.750 1.000 3870 4837 5805 6966
12 12.750 1.000 3263 4078 4894 5873
NOTES
TECHNICAL DATA

123
SCHEDULE STD WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.109 6748 8435 10121 12146
3/4 1.050 0.113 5596 6995 8394 10073
1 1.315 0.133 5259 6574 7889 9467
1 1/4 1.660 0.140 4386 5482 6578 7894
1 1/2 1.900 0.145 3968 4961 5953 7143
2 2.375 0.154 3372 4215 5058 6069
2 1/2 2.875 0.203 3672 4590 5507 6609
3 3.500 0.216 3209 4011 4814 5776
3 1/2 4.000 0.226 2938 3673 4407 5288
4 4.500 0.237 2739 3423 4108 4930
5 5.563 0.258 2412 3015 3617 4341
6 6.625 0.280 2198 2747 3297 3956
8 8.625 0.322 1941 2427 2912 3494
10 10.750 0.365 1766 2207 2648 3178
12 12.750 0.375 1529 1912 2294 2753
14 14.000 0.375 1393 1741 2089 2507
16 16.000 0.375 1219 1523 1828 2194
18 18.000 0.375 1083 1354 1625 1950
20 20.000 0.375 975 1219 1463 1755
24 24.000 0.375 813 1016 1219 1463
30 30.000 0.375 650 813 975 1170
36 36.000 0.375 542 677 813 975
42 42.000 0.375 464 580 696 836
48 48.000 0.375 406 508 609 731
NOTES
TECHNICAL DATA


TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE XS WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.147 9100 11375 13650 16380
3/4 1.050 0.154 7627 9533 11440 13728
1 1.315 0.179 7078 8848 10617 12741
1 1/4 1.660 0.191 5983 7479 8975 10770
1 1/2 1.900 0.200 5474 6842 8211 9853
2 2.375 0.218 4773 5966 7160 8591
2 1/2 2.875 0.276 4992 6240 7488 8986
3 3.500 0.300 4457 5571 6686 8023
3 1/2 4.000 0.318 4134 5168 6201 7441
4 4.500 0.337 3894 4868 5841 7010
5 5.563 0.375 3505 4382 5258 6310
6 6.625 0.432 3391 4238 5086 6103
8 8.625 0.500 3014 3768 4522 5426
10 10.750 0.500 2419 3023 3628 4353
12 12.750 0.500 2039 2549 3059 3671
14 14.000 0.500 1857 2321 2786 3343
16 16.000 0.500 1625 2031 2438 2925
18 18.000 0.500 1444 1806 2167 2600
20 20.000 0.500 1300 1625 1950 2340
24 24.000 0.500 1083 1354 1625 1950
30 30.000 0.500 867 1083 1300 1560
36 36.000 0.500 722 903 1083 1300
42 42.000 0.500 619 774 929 1114
48 48.000 0.500 542 677 813 975
NOTES
TECHNICAL DATA


125
SCHEDULE 40 WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
12 12.750 0.406 1656 2070 2484 2981
14 14.000 0.438 1627 2034 2440 2928
16 16.000 0.500 1625 2031 2438 2925
18 18.000 0.562 1624 2029 2435 2922
20 20.000 0.594 1544 1931 2317 2780
24 24.000 0.688 1491 1863 2236 2683
36 36.000 0.750 1083 1354 1625 1950

SCHEDULE 80 WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
10 10.750 0.594 2873 3592 4310 5172
12 12.750 0.688 2806 3507 4209 5051
14 14.000 0.750 2786 3482 4179 5014
16 16.000 0.844 2743 3429 4115 4937
18 18.000 0.938 2710 3387 4065 4878
20 20.000 1.031 2681 3351 4021 4825
24 24.000 1.219 2641 3301 3962 4754
TECHNICAL DATA

NOTES
WPHY-65
126

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE 160 WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.188 11638 14548 17457 20949
3/4 1.050 0.219 10846 13557 16269 19522
1 1.315 0.250 9886 12357 14829 17795
1 1/4 1.660 0.250 7831 9789 11747 14096
1 1/2 1.900 0.281 7691 9613 11536 13843
2 2.375 0.344 7532 9415 11298 13557
2 1/2 2.875 0.375 6783 8478 10174 12209
3 3.500 0.438 6507 8134 9761 11713
4 4.500 0.531 6136 7670 9204 11045
5 5.563 0.625 5842 7303 8763 10516
6 6.625 0.719 5643 7054 8465 10158
8 8.625 0.906 5462 6828 8193 9832
10 10.750 1.125 5442 6802 8163 9795
12 12.750 1.312 5351 6689 8026 9632
14 14.000 1.406 5222 6528 7833 9400
16 16.000 1.594 5181 6476 7771 9325
18 18.000 1.781 5145 6431 7718 9261
20 20.000 1.969 5119 6399 7679 9215
24 24.000 2.344 5079 6348 7618 9142
NOTES
TECHNICAL DATA

127
SCHEDULE XXS WPHY-65
For reference only

Thickness
Outside Inches
Diameter
Size
O.D. T 0.40 0.50 0.60 0.72
1/2 0.840 0.294 18200 22750 27300 32760
3/4 1.050 0.308 15253 19067 22880 27456
1 1.315 0.358 14157 17696 21235 25482
1 1/4 1.660 0.382 11966 14958 17949 21539
1 1/2 1.900 0.400 10947 13684 16421 19705
2 2.375 0.436 9546 11933 14319 17183
2 1/2 2.875 0.552 9984 12480 14976 17971
3 3.500 0.600 8914 11143 13371 16046
4 4.500 0.674 7788 9736 11683 14019
5 5.563 0.750 7011 8763 10516 12619
6 6.625 0.864 6782 8477 10172 12207
8 8.625 0.875 5275 6594 7913 9496
10 10.750 1.000 4837 6047 7256 8707
12 12.750 1.000 4078 5098 6118 7341
NOTES
TECHNICAL DATA

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com Flow resistance for fittings
Equivalent length of weldbend elbows and tees
Nominal Pipe Size Long Radius Short Radius Welding Tee

1 1.1 1.4 3.9
1 1/4 1.4 1.8 5.2
1 1/2 1.6 2.1 6.0
2 2.1 2.8 7.8
2 1/2 2.6 3.3 9.3
3 3.1 4.1 11.0
4 4.0 5.4 15.0
5 5.1 6.7 19.0
6 6.1 8.1 23.0
8 8.0 11.0 30.0
10 10.0 12.0 38.0
12 12.0 16.0 45.0
14 13.0 18.0 49.0
16 15.0 20.0 56.0
18 17.0 23.0 63.0
20 19.0 25.0 71.0
24 23.0 30.0 85.0
30 30.0 36.0 140.0
36 38.0 42.0 170.0
42 45.0 50.0 200.0
48 52.0 58.0 240.0
TECHNICAL DATA
The information given in the chart above illustrates the resistance of fittings to the flow of liquids.
This resistance is given in the equivalent of the straight pipe, and should be assumed as approximate information.
Allowances have been made up for the curvature of elbows, so that the resistance values should be added to the total
center-to-end dimensions of the piping configuration.
As an example: Using 6" pipe: Resistance of Pipe: (6.6 + 6.4 + 6.6) = 19.6
+ Resistance of Elbow: = 6.1
Resistance of Tee: = 23.0
= 48.7
Therefore, the total resistance of the entire assembly to the flow of liquid would be equal to the resistance of 48.7 Linear feet
of 6" straight pipe. 129

Flow resistance for fittings
There are a number of general formulas for determination of steady flow

pressure drop available. One preferred by many is expressed as follows:
Δp = .00219ƒpv²L
d
Where: Δp = Pressure drop (psi)

ƒ = Friction factor (dimensionless)
þ = Density (lb/ft³)
v = Velocity of flow (ft/sec)
L = Equivalent length of straight pipe (ft)
d = Inside diameter of pipe (in)
In order to determine the friction factor, f, for use with this formula, it is necessary to first calculate
the appropriate Reynolds number, R, and then to select it from the graph below.
The formula for calculating R is:
R = 124dvþ
µ
Where: R = Reynolds number (dimensionless)

µ = Absolute viscosity (centipoise)
Values for þ and µ for different liquids and gases are available in various engineering handbooks.
As an example, if water at 70ºF is flowing through the 6" assembly of the previous page at an average
velocity of 20 ft/sec. the pressure drop due to flow friction (only) may be calculated as follows:
For water µ = 470 (T + 30) -1.35 = 0.94 and þ = 62.37lb/ft3
R = 124(6.06)(20)(62.37) = 997000 ≈ 10⁶

0.94
then ƒ = .015 (From graph below)
and Δp = .00129(.015)(62.37)(20)2(48.43) = 3.86 ≈ 4

6.06
Therefore, the approximate pressure drop from flange to flange, due only to flow friction, is 4 psi.
Calculation of total pressure drop would have to also take into account any change in elevation.
STREAMLINE CRITICAL ZONE TURBULENT FLOW

FLOW
.07
.06
ƒ = 64 / R
.05
.04
TECHNICAL DATA
ƒ .03
½" IPS
.02
1" IPS
2 ½" IPS
6" IPS
.01 14" TO 24"

103 2 3 4 5 6 8 104 2 3 4 5 6 8 105 2 3 4 5 6 8 106 2 3 4 5 6 107
R E Y NOL D S NUMBE R - R
130

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com Flexibility and stress intensification factors
Stress Intensification
Factor [Notes 2, 3]
Flexibility Flexibility
Description Factor Out-plane In-plane Characteristic Sketch
k io ii h
T
Welding elbow T R1
1.65 0.75 0.9 r2
or pipe bend
h h 2/3 h 2/3 r 2
[Notes 1, 2] 2 R1= bend
radius
Welding tee with T

rx ≥ 0.05 Db
TTcc < 1.5 T
1
0.9
h2/3
3/4 io + 1/4 ( ) rx
1+ r
2
T
r2 Tc r2
[Notes 1, 2, 3] rx
Welding tee with T

rx ≥ 1/8 Db 0.9 T
1 3/4 io + 1/4 4.4 r Tc r2
Tc ≥ 1.5 T h2/3 2
[Notes 1, 2, 3] rx
Stress
Flexibility Intensification
Description Factor Factor
k i
Butt welded joint, reducer, or weld neck flange 1 1.0
Double-welded slip-on flange 1 1.2
Lap joint flange (with ASME B16.9 lap joint stub) 1 1.6
Threaded pipe joint, or threaded flange 1 2.3
1.00
1 END FLANGED C1 = h1/6
0.75
CORR
FACTOR 0.50
C1 2 ENDS FLANGED C1 = h1/3
0.375
TECHNICAL DATA
0.25
0.0 0.03 0.04 0.06 0.10 0.15 0.2 0.3 0.4 0.6 0.8 1.0 1.5 2.0
NOTES
1. The flexibility factor, k, applies to bending in any plane. The flexibility factor k, and stress intensification factor, i, shall not be less than unity.
2. T = Nominal wall thickness of elbows. R1 = Bend radius of elbows.
T = Nominal wall thickness of matching pipe of tees. rx = See definition in appropriate section of B31.
Tc = Crotch thickness of tees. Db = Outside diameter of branch.
r2 = Mean radius of matching pipe.
3. When radius and thickness limits are not met for this component, use h = T/r2.
4. Where flanges are attached to one or both ends, the values of k and i shall be corrected by the factors C1 from graph above.
131

thermal expansion for carbon steel pipe
Total linear thermal expansion from 70° F to the Temperature
Temperature Expansion Temperature Expansion

°F Inches / 100 ft. °F Inches / 100 ft.
-325 -2.37 575 4.35
-300 -2.24 600 4.60
-275 -2.11 625 4.86
-250 -1.98 650 5.11
-225 -1.85 675 5.37
-200 -1.71 700 5.63
-175 -1.30 725 5.90
-150 -1.45 750 6.16
-125 -1.30 775 6.43
-100 -1.15 800 6.70
-75 -1.00 825 6.97
-50 -0.84 850 7.25
-25 -0.68 875 7.53
0 -0.49 900 7.81
25 -0.32 925 8.08
50 -0.14 950 8.35
70 0.00 975 8.62
100 0.23 1000 8.89
125 0.42 1075 9.75
150 0.61 1050 9.46
200 0.99 1075 9.75
225 1.21 1100 10.04
250 1.40 1125 10.31
275 1.61 1150 10.57
300 1.82 1175 10.83
325 2.04 1200 11.10
350 2.26 1225 11.38
375 2.48 1250 11.66
400 2.70 1275 11.94
425 2.93 1300 12.22
450 3.16 1325 12.50
475 3.39 1350 12.78
TECHNICAL DATA
500 3.62 1375 13.06

525 3.86 1400 13.34
550 4.11
132

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com dimensions of welding ends
SCHEDULE STD
For reference only
Wall Thickness Outside Diameter Inside Diameter Wall Thickness

Pipe Size
Designation
O.D. I.D. T
1/2 STD 0.840 0.622 0.109
3/4 STD 1.050 0.824 0.113
1 STD 1.315 1.049 0.133
1 1/4 STD 1.660 1.380 0.140
1 1/2 STD 1.900 1.610 0.145
2 STD 2.375 2.067 0.154
2 1/2 STD 2.875 2.469 0.203
3 STD 3.500 3.068 0.216
3 1/2 STD 4.000 3.548 0.226
4 STD 4.500 4.026 0.237
5 STD 5.563 5.047 0.258
6 STD 6.625 6.065 0.280
8 STD 8.625 7.981 0.322
10 STD 10.750 10.020 0.365
12 STD 12.750 12.000 0.375
14 STD 14.000 13.250 0.375
16 STD 16.000 15.250 0.375
18 STD 18.000 17.250 0.375
20 STD 20.000 19.250 0.375
24 STD 24.000 23.250 0.375
30 STD 30.000 29.250 0.375
36 STD 36.000 35.250 0.375
42 STD 42.000 41.250 0.375
48 STD 48.000 47.250 0.375
NOTES
2. Designations per ASME B36.10.
STD = Schedule Standard Wall Thickness
3. Conforms to ASME B36.10.
TECHNICAL DATA
133

dimensions of welding ends
SCHEDULE XS
For reference only

Pipe Size
Designation
O.D. I.D. T
1/2 XS 0.840 0.546 0.147
3/4 XS 1.050 0.742 0.154
1 XS 1.315 0.957 0.179
1 1/4 XS 1.660 1.278 0.191
1 1/2 XS 1.900 1.500 0.200
2 XS 2.375 1.939 0.218
2 1/2 XS 2.875 2.323 0.276
3 XS 3.500 2.900 0.300
3 1/2 XS 4.000 3.364 0.318
4 XS 4.500 3.826 0.337
5 XS 5.563 4.813 0.375
6 XS 6.625 5.761 0.432
8 XS 8.625 7.625 0.500
10 XS 10.750 9.750 0.500
12 XS 12.750 11.750 0.500
14 XS 14.000 13.000 0.500
16 XS 16.000 15.000 0.500
18 XS 18.000 17.000 0.500
20 XS 20.000 19.000 0.500
24 XS 24.000 23.000 0.500
30 XS 30.000 29.000 0.500
36 XS 36.000 35.000 0.500
42 XS 42.000 41.000 0.500
48 XS 48.000 47.000 0.500
NOTES
XS = Schedule Extra-Strong Wall Thickness
TECHNICAL DATA
134

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE 40
For reference only

Pipe Size
Designation
O.D. I.D. T
12 40 12.750 11.938 0.406
14 40 14.000 13.124 0.438
16 40 16.000 15.000 0.500
18 40 18.000 16.876 0.562
20 40 20.000 18.812 0.594
24 40 24.000 22.624 0.688
36 40 36.000 34.500 0.750
SCHEDULE 80
For reference only

Pipe Size
Designation
O.D. I.D. T
14 80 14.000 12.500 0.750
16 80 16.000 14.312 0.844
18 80 18.000 16.124 0.938
20 80 20.000 17.938 1.031
24 80 24.000 21.562 1.219
NOTES
40 = Schedule 40 Wall Thickness
TECHNICAL DATA
135

dimensions of welding ends
SCHEDULE 160
For reference only

Pipe Size
Designation
O.D. I.D. T
1/2 160 0.840 0.464 0.188
3/4 160 1.050 0.612 0.219
1 160 1.315 0.815 0.250
1 1/4 160 1.660 1.160 0.250
1 1/2 160 1.900 1.338 0.281
2 160 2.375 1.687 0.344
2 1/2 160 2.875 2.125 0.375
3 160 3.500 2.624 0.438
4 160 4.500 3.438 0.531
5 160 5.563 4.313 0.625
6 160 6.625 5.187 0.719
8 160 8.625 6.813 0.906
10 160 10.750 8.500 1.125
12 160 12.750 10.126 1.312
14 160 14.000 11.188 1.406
16 160 16.000 12.812 1.594
18 160 18.000 14.438 1.781
20 160 20.000 16.062 1.969
24 160 24.00 19.314 2.343
NOTES
TECHNICAL DATA
136

TEL: 708/594-1700
FAX: 708/458-0106
SCHEDULE xxs
For reference only

Pipe Size
Designation
O.D. I.D. T
1/2 XXS 0.840 0.252 0.294
3/4 XXS 1.050 0.434 0.308
1 XXS 1.315 0.599 0.358
1 1/4 XXS 1.660 0.896 0.382
1 1/2 XXS 1.900 1.100 0.400
2 XXS 2.375 1.503 0.436
2 1/2 XXS 2.875 1.771 0.552
3 XXS 3.500 2.300 0.600
4 XXS 4.500 3.152 0.674
5 XXS 5.563 4.063 0.750
6 XXS 6.625 4.897 0.864
8 XXS 8.625 6.875 0.875
10 XXS 10.750 8.750 1.000
12 XXS 12.750 10.750 1.000
NOTES
XXS = Schedule Double Extra-Strong Wall Thickness
TECHNICAL DATA
137

dimensions of steel pipe
Outside Wall Inside Sq. Ft. Sq. Ft.

Designation Weight of
Pipe Diameter Thickness Diameter Weight Per Outside Inside
Water per
Size Foot Surface Surface
Foot of Pipe
O.D. SCH T I.D. per Ft. per Ft.
5 0.065 0.710 0.54 0.172 0.220 0.186
10 0.083 0.674 0.67 0.155 0.220 0.176
30 0.095 0.650 0.76 0.144 0.220 0.170
1/2 0.840 STD (40) 0.109 0.622 0.85 0.132 0.220 0.163
XS (80) 0.147 0.546 1.09 0.101 0.220 0.143
160 0.188 0.464 1.31 0.073 0.220 0.121
XXS 0.294 0.252 1.72 0.022 0.220 0.066
5 0.065 0.920 0.69 0.288 0.275 0.241

10 0.083 0.884 0.86 0.266 0.275 0.231
30 0.095 0.860 0.97 0.252 0.275 0.225
3/4 1.050 STD (40) 0.113 0.824 1.13 0.231 0.275 0.216
XS (80) 0.154 0.742 1.48 0.187 0.275 0.194
160 0.219 0.612 1.95 0.127 0.275 0.160
XXS 0.308 0.434 2.44 0.064 0.275 0.114
5 0.065 1.185 0.87 0.478 0.344 0.310

10 0.109 1.097 1.41 0.409 0.344 0.287
30 0.114 1.087 1.46 0.402 0.344 0.285
1 1.315 STD (40) 0.133 1.049 1.68 0.374 0.344 0.275
XS (80) 0.179 0.957 2.17 0.312 0.344 0.251
160 0.250 0.815 2.85 0.226 0.344 0.213
XXS 0.358 0.599 3.66 0.122 0.344 0.157
5 0.065 1.530 1.11 0.796 0.435 0.401

10 0.109 1.442 1.81 0.707 0.435 0.378
30 0.117 1.426 1.93 0.692 0.435 0.373
1 1/4 1.660 STD (40) 0.140 1.380 2.27 0.648 0.435 0.361
XS (80) 0.191 1.278 3.00 0.556 0.435 0.335
160 0.250 1.160 3.77 0.458 0.435 0.304
XXS 0.382 0.896 5.22 0.273 0.435 0.235
TECHNICAL DATA
5 0.065 1.770 1.28 1.066 0.497 0.463

10 0.109 1.682 2.09 0.963 0.497 0.440
30 0.125 1.650 2.37 0.926 0.497 0.432
1 1/2 1.900 STD (40) 0.145 1.610 2.72 0.882 0.497 0.421
XS (80) 0.200 1.500 3.63 0.766 0.497 0.393
160 0.281 1.338 4.86 0.609 0.497 0.350
XXS 0.400 1.100 6.41 0.412 0.497 0.288
138

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com dimensions of steel pipe

Water per
Foot of Pipe
5 0.065 2.245 1.61 1.715 0.622 0.588
10 0.109 2.157 2.64 1.583 0.622 0.565
30 0.125 2.125 3.01 1.536 0.622 0.556
2 2.375 STD (40) 0.154 2.067 3.66 1.454 0.622 0.541
XS (80) 0.218 1.939 5.03 1.279 0.622 0.508
160 0.344 1.687 7.47 0.968 0.622 0.442
XXS 0.436 1.503 9.04 0.769 0.622 0.393
5 0.083 2.709 2.48 2.497 0.753 0.709

10 0.120 2.635 3.53 2.362 0.753 0.690
30 0.188 2.499 5.40 2.125 0.753 0.654
2 1/2 2.875 STD (40) 0.203 2.469 5.80 2.074 0.753 0.646
XS (80) 0.276 2.323 7.67 1.836 0.753 0.608
160 0.375 2.125 10.02 1.536 0.753 0.556
XXS 0.552 1.771 13.71 1.067 0.753 0.464
5 0.083 3.334 3.03 3.782 0.916 0.873

10 0.120 3.260 4.34 3.616 0.916 0.853
30 0.188 3.124 6.66 3.320 0.916 0.818
3 3.500 STD (40) 0.216 3.068 7.58 3.202 0.916 0.803
XS (80) 0.300 2.900 10.26 2.861 0.916 0.759
160 0.438 2.624 14.34 2.343 0.916 0.687
XXS 0.600 2.300 18.60 1.800 0.916 0.602
5 0.083 3.834 3.48 5.001 1.047 1.004

10 0.120 3.760 4.98 4.810 1.047 0.984
3 1/2 4.000 30 0.188 3.624 7.66 4.468 1.047 0.949
STD (40) 0.226 3.548 9.12 4.283 1.047 0.929
XS (80) 0.318 3.364 12.52 3.850 1.047 0.881
5 0.083 4.334 3.92 6.391 1.178 1.135

TECHNICAL DATA
10 0.120 4.260 5.62 6.174 1.178 1.115

30 0.188 4.124 8.67 5.786 1.178 1.080
STD (40) 0.237 4.026 10.80 5.515 1.178 1.054
4 4.500
XS (80) 0.337 3.826 15.00 4.980 1.178 1.002
120 0.438 3.624 19.02 4.468 1.178 0.949
160 0.531 3.438 22.53 4.022 1.178 0.900
XXS 0.674 3.152 27.57 3.380 1.178 0.825
139


Water per
Foot of Pipe
5 0.109 5.345 6.36 9.720 1.456 1.399
10 0.134 5.295 7.78 9.539 1.456 1.386
STD (40) 0.258 5.047 14.63 8.667 1.456 1.321
5 5.563 XS (80) 0.375 4.813 20.80 7.882 1.456 1.260
120 0.500 4.563 27.06 7.084 1.456 1.195
160 0.625 4.313 32.99 6.329 1.456 1.129
XXS 0.750 4.063 38.59 5.617 1.456 1.064
5 0.109 6.407 7.59 13.967 1.734 1.677

10 0.134 6.357 9.30 13.749 1.734 1.664
STD (40) 0.280 6.065 18.99 12.515 1.734 1.588
6 6.625 XS (80) 0.432 5.761 28.60 11.292 1.734 1.508
120 0.562 5.501 36.43 10.296 1.734 1.440
160 0.719 5.187 45.39 9.154 1.734 1.358
XXS 0.864 4.897 53.21 8.159 1.734 1.282
5 0.109 8.407 9.92 24.047 2.258 2.201

10 0.148 8.329 13.41 23.603 2.258 2.181
20 0.250 8.125 22.38 22.461 2.258 2.127
30 0.277 8.071 24.72 22.163 2.258 2.113
STD (40) 0.322 7.981 28.58 21.672 2.258 2.089
60 0.406 7.813 35.67 20.769 2.258 2.045
8 8.625
XS (80) 0.500 7.625 43.43 19.781 2.258 1.996
100 0.594 7.437 51.00 18.818 2.258 1.947
120 0.719 7.187 60.77 17.574 2.258 1.882
140 0.812 7.001 67.82 16.676 2.258 1.833
XXS 0.875 6.875 72.49 16.081 2.258 1.800
160 0.906 6.813 74.76 15.793 2.258 1.784
5 0.134 10.482 15.21 37.382 2.814 2.744

10 0.165 10.420 18.67 36.941 2.814 2.728
TECHNICAL DATA
20 0.250 10.250 28.06 35.746 2.814 2.683

30 0.307 10.136 34.27 34.955 2.814 2.654
STD (40) 0.365 10.020 40.52 34.160 2.814 2.623
10 10.750 XS (60) 0.500 9.750 54.79 32.344 2.814 2.553
80 0.594 9.562 64.49 31.108 2.814 2.503
100 0.719 9.312 77.10 29.503 2.814 2.438
120 0.844 9.062 89.38 27.940 2.814 2.372
XXS (140) 1.000 8.750 104.23 26.049 2.814 2.291
160 1.125 8.500 115.75 24.582 2.814 2.225
140

TEL: 708/594-1700
FAX: 708/458-0106

Water per
Foot of Pipe
5 0.156 12.438 21.00 52.636 3.338 3.256
10 0.180 12.390 24.19 52.230 3.338 3.244
20 0.250 12.250 33.41 51.056 3.338 3.207
30 0.330 12.090 43.81 49.731 3.338 3.165
STD 0.375 12.000 49.61 48.994 3.338 3.142
40 0.406 11.938 53.47 48.489 3.338 3.125
12 12.750 XS 0.500 11.750 65.48 46.974 3.338 3.076
60 0.562 11.626 73.22 45.987 3.338 3.044
80 0.688 11.374 88.71 44.015 3.338 2.978
100 0.844 11.062 107.42 41.634 3.338 2.896
XXS (120) 1.000 10.750 125.61 39.318 3.338 2.814
140 1.125 10.500 139.81 37.511 3.338 2.749
160 1.312 10.126 160.42 34.886 3.338 2.651
5 0.156 13.688 23.09 63.747 3.665 3.584

10 0.250 13.500 36.75 62.008 3.665 3.534
20 0.312 13.376 45.65 60.874 3.665 3.502
STD (30) 0.375 13.250 54.62 59.732 3.665 3.469
40 0.438 13.124 63.50 58.602 3.665 3.436
XS 0.500 13.000 72.16 57.500 3.665 3.403
14 14.000
60 0.594 12.812 85.13 55.849 3.665 3.354
80 0.750 12.500 106.23 53.162 3.665 3.272
100 0.938 12.124 130.98 50.012 3.665 3.174
120 1.094 11.812 150.93 47.471 3.665 3.092
140 1.250 11.500 170.37 44.996 3.665 3.011
160 1.406 11.188 189.29 42.588 3.665 2.929
5 0.165 15.670 27.93 83.544 4.189 4.102

10 0.250 15.500 42.09 81.741 4.189 4.058
20 0.312 15.376 52.32 80.439 4.189 4.025
STD (30) 0.375 15.250 62.64 79.126 4.189 3.992
XS (40) 0.500 15.000 82.85 76.553 4.189 3.927
TECHNICAL DATA
16 16.000 60 0.656 14.688 107.60 73.401 4.189 3.845

80 0.844 14.312 136.74 69.691 4.189 3.747
100 1.031 13.938 164.98 66.097 4.189 3.649
120 1.219 13.562 192.61 62.579 4.189 3.551
140 1.438 13.124 223.85 58.602 4.189 3.436
160 1.594 12.812 245.48 55.849 4.189 3.354
141


Water per
Foot of Pipe
5 0.165 17.670 31.46 106.231 4.712 4.626
10 0.250 17.500 47.44 104.197 4.712 4.581
20 0.312 17.376 58.99 102.725 4.712 4.549
STD 0.375 17.250 70.65 101.241 4.712 4.516
30 0.438 17.124 82.23 99.767 4.712 4.483
XS 0.500 17.000 93.54 98.328 4.712 4.451
18 18.000 40 0.562 16.876 104.76 96.899 4.712 4.418
60 0.750 16.500 138.30 92.629 4.712 4.320
80 0.938 16.124 171.08 88.455 4.712 4.221
100 1.156 15.688 208.15 83.736 4.712 4.107
120 1.375 15.250 244.37 79.126 4.712 3.992
140 1.562 14.876 274.48 75.292 4.712 3.895
160 1.781 14.438 308.79 70.924 4.712 3.780
5 0.188 19.624 39.82 131.025 5.236 5.138

10 0.250 19.500 52.78 129.374 5.236 5.105
STD (20) 0.375 19.250 78.67 126.078 5.236 5.040
XS (30) 0.500 19.000 104.23 122.825 5.236 4.974
40 0.594 18.812 123.23 120.406 5.236 4.925
20 20.000 60 0.812 18.376 166.56 114.889 5.236 4.811
80 1.031 17.938 209.06 109.478 5.236 4.696
100 1.281 17.438 256.34 103.460 5.236 4.565
120 1.500 17.000 296.65 98.328 5.236 4.451
140 1.750 16.500 341.41 92.629 5.236 4.320
160 1.969 16.062 379.53 87.776 5.236 4.205
5 0.218 23.564 55.42 188.919 6.283 6.169

10 0.250 23.500 63.47 187.894 6.283 6.152
STD (20) 0.375 23.250 94.71 183.918 6.283 6.087
XS 0.500 23.000 125.61 179.984 6.283 6.021
30 0.562 22.876 140.81 178.049 6.283 5.989
40 0.688 22.624 171.45 174.147 6.283 5.923
TECHNICAL DATA
24 24.000
60 0.969 22.062 238.57 165.603 6.283 5.776
80 1.219 21.562 296.86 158.182 6.283 5.645
100 1.531 20.938 367.74 149.159 6.283 5.482
120 1.812 20.376 429.79 141.259 6.283 5.334
140 2.062 19.876 483.57 134.411 6.283 5.204
160 2.344 19.312 542.67 126.892 6.283 5.056
142

TEL: 708/594-1700
FAX: 708/458-0106

Water per
Foot of Pipe
5 0.250 29.500 79.51 296.089 7.854 7.723
10 0.312 29.376 99.02 293.605 7.854 7.691
30 30.000 STD 0.375 29.250 118.76 291.092 7.854 7.658
XS (20) 0.500 29.000 157.68 286.137 7.854 7.592
30 0.625 28.750 196.26 281.225 7.854 7.527
10 0.312 35.376 119.03 425.790 9.425 9.261

STD 0.375 35.250 142.81 422.763 9.425 9.228
36 36.000 XS (20) 0.500 35.000 189.75 416.787 9.425 9.163
30 0.625 34.750 236.35 410.854 9.425 9.098
40 0.750 34.500 282.62 404.964 9.425 9.032
STD 0.375 41.250 166.86 578.930 10.996 10.799

42 42.000
XS 0.500 41.000 221.82 571.934 10.996 10.734
STD 0.375 47.250 190.92 759.595 12.566 12.370

48 48.000
XS 0.500 47.000 253.89 751.578 12.566 12.305
TECHNICAL DATA
143

dimensional tolerances for flanges
For weldbend forged steel pipe flanges
Listed below are the dimensional tolerances to which Weldbend flanges

are manufactured. These tolerances are a part of ASME B16.5 except where
noted otherwise. The limits given are maximum.
Slip-on, Threaded, Blind and Lap Joint Welding Neck **

When O.D. is When O.D. is
± .06" * ± .06"
Outside 24" or Less Outside 24" or Less
Diameter When O.D. is Diameter When O.D. is
± .12" * ± .12"
Over 24" Over 24"
10" and Smaller
To Standard ± .03"
Threaded
Gauge Limits* Inside 12" through 18"
Inside Diameter ± .06"
Diameter 10" and Smaller 20" through 48"
Slip-on and + .03" , – 0" * + .12" , – .06"
Lap Joint 12" and Larger Diameter NPS < 10" ± .03"
+ .06", – 0" * of Contact Face NPS > 12" ± .06"
NPS < 5" + .09" , – .03 " * Bolt Circle
Outside ± .06"
Diameter
Diameter
of Hub NPS > 6" + .16" , – .03" * Hole Spacing ± .03"
Drilling 2 1/2" and Smaller
Diameter NPS < 10" ± .03" Bolt Circle ± .03"
of Contact Face NPS > 12" ± .06" Concentricity 3" and Larger
± .06"
Diameter NPS < 10" + .03" , – 0" NPS < 18" + .12" , – 0"
of Counterbore Thickness
(Threaded) NPS > 20" + .19" , – 0"
NPS > 12" + .06" , – 0"
NPS < 4" ± .06"
Bolt Circle Length 5" < NPS < 10" + .06" , – .12"
± .06"
Diameter Thru
Hub 12" < NPS < 24" + .12" , – .18"
Hole Spacing ± .03" NPS > 26" + .12" , –.18"
Drilling
2 1/2" and Smaller NOTES
± .03" 1. All dimensions are in inches.
Bolt Circle * This Tolerance not covered in ASME B16.5.
Concentricity 3" and Larger ** For bevel detail see page 107.
± .06" *** This Tolerance applies to flat face flanges, sizes 1/2" through 24", and sizes 3"
and larger flanges with raised face and other machined facings.
TECHNICAL DATA
NPS < 18" + .12" , – 0"

Thickness
NPS > 20" + .19" , – 0"
10" and Smaller
NPS < 10"
Length ± .06" * , – 0" *
Refer to Section 7 of ASME B16.5 for complimwntary information.
Thru Hub 12" through 48"
NPS > 12"
± .12" *
144

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com gasket surface finishes
Flanges, welding necks, and other products designed for bolted connection,
when furnished with raised face (or flat faced) may have any type of gasket
surface finished that is required. The common finishes are described in
the following paragraphs and it should be noted particularly that, unless
otherwise specified by the purchaser, the STOCK FINISH will be furnished.
Stock Finish (Weldbend Standard finish)
From 125 micro inches to 250 micro inches average roughness shall be furnished. The
cutting tool employed should have an approximate 0.06 inches or larger radius.
Smooth Finish
This finish, which can be produced by several shapes of tools, shows no definite tool
markings apparent to the naked eye. In the past this finish was sometimes known as
“Smooth Plane”. This term, however, should be avoided because of a tendency to
confuse it with “flat faced” which, of course, applies to the flange facing and not
to the gasket surface finish.
Cold Water Finish
Producing by using a wide tool at high speeds, this finish is equivalent to that of
a ground surface. It is mirror-like in appearance and surfaces finished in this manner
are usually expected to be used without gaskets.
Spiral Serrated
This too, is a continuous spiral groove, but it differs from the stock finish in that the groove
is generated with a 90° included angle “V” tool. This groove is 1/64" deep and the feed is
1/32" for all sizes.
Concentric Serrated
TECHNICAL DATA
As the name suggests this surface finish is made up of concentric grooves. A 90° included
angle “V” tool is used and the grooves are 1/64" deep and 1/32" apart.
145

standard flange facings
1/4"
FLAT FACE 1/4" RAISED FACE
Optional Class 400 – 2500
(All Classes)
1/16"
1/16" RAISED FACE
Class 150 & 300
TECHNICAL DATA
146

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com standard flange facings
Facing dimensions (Other than Ring Joints)
Below are B16.5 facing dimensions for Classes 150,

300, 600, 900, 1500 and 2500* through 24 inches.
Above 24" is in accord with ASME B16.47.
Outside Maximum Radial Maximum Depth
Height Projection of and Projection of
Diameter
Pipe Pipe Imperfections Which Imperfections Which
Size Raised Face Size Are No Deeper Than Are Deeper Than
Raised Face
Raised Face, Class 150 the Bottom of the the Bottom of the
Class 400 - 2500
& 300 Serrations, in. Serrations, in.
1/2 1.38 0.06 0.25 1/2 0.12 0.06
3/4 1.69 0.06 0.25 3/4 0.12 0.06
1 2.00 0.06 0.25 1 0.12 0.06
1 1/4 2.50 0.06 0.25 1 1/4 0.12 0.06
1 1/2 2.88 0.06 0.25 1 1/2 0.12 0.06
2 3.62 0.06 0.25 2 0.12 0.06
2 1/2 4.12 0.06 0.25 2 1/2 0.12 0.06
3 5.00 0.06 0.25 3 0.18 0.06
3 1/2 5.50 0.06 0.25 3 1/2 0.25 0.12
4 6.19 0.06 0.25 4 0.25 0.12
5 7.31 0.06 0.25 5 0.25 0.12
6 8.50 0.06 0.25 6 0.25 0.12
8 10.62 0.06 0.25 8 0.31 0.18
10 12.75 0.06 0.25 10 0.31 0.18
12 15.00 0.06 0.25 12 0.31 0.18
14 16.25 0.06 0.25 14 0.31 0.18
16 18.50 0.06 0.25 16 0.38 0.18
18 21.00 0.06 0.25 18 0.50 0.25
20 23.00 0.06 0.25 20 0.50 0.25
24 27.25 0.06 0.25 24 0.50 0.25
NOTES
2. Finishes for raised face portion of the flange can be found on page 145.
3. Flange finishing is also in accordance with MSS-SP6.
4. For facing tolerances, see page 144.
TECHNICAL DATA
* ASME B16.5 only covers 2500 flanges up thru 12".
147

ring type joint fACING DIMENSIONS
CLASS 150
Nominal Groove Dimensions

Groove
Outside Number Pitch Radius at Diameter of
Pipe Depth Width
Diameter Diameter Bottom Gasket
Size
O.D. P E F R K
1 4.25 R15 1.875 0.250 0.344 0.03 2.50
1 1/4 4.62 R17 2.250 0.250 0.344 0.03 2.88
1 1/2 5.00 R19 2.562 0.250 0.344 0.03 3.25
2 6.00 R22 3.250 0.250 0.344 0.03 4.00
2 1/2 7.00 R25 4.000 0.250 0.344 0.03 4.75
3 7.50 R29 4.500 0.250 0.344 0.03 5.25
3 1/2 8.50 R33 5.188 0.250 0.344 0.03 6.06
4 9.00 R36 5.875 0.250 0.344 0.03 6.75
5 10.00 R40 6.750 0.250 0.344 0.03 7.62
6 11.00 R43 7.625 0.250 0.344 0.03 8.62
8 13.50 R48 9.750 0.250 0.344 0.03 10.75
10 16.00 R52 12.000 0.250 0.344 0.03 13.00
12 19.00 R56 15.000 0.250 0.344 0.03 16.00
14 21.00 R59 15.625 0.250 0.344 0.03 16.75
16 23.50 R64 17.875 0.250 0.344 0.03 19.00
18 25.00 R68 20.375 0.250 0.344 0.03 21.50
20 27.50 R72 22.000 0.250 0.344 0.03 23.50
24 32.00 R76 26.500 0.250 0.344 0.03 28.00
NOTES
2. Height of raised portion is equal to the depth of grove
TECHNICAL DATA
dimension E, but is not subjected to the tolerances for E.

Former full-face contour may be used.
3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
P (pitch diameter) ± 0.005
R (radius at bottom)
R < 0.06 + 0.03, - 0.0;
R > 0.06 ± 0.03
23° (angle) = ½°
148

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com ring type joint fACING DIMENSIONS
CLASS 300

Groove
Pipe Depth Width
Size
O.D. P E F R K
1/2 3.75 R11 1.344 0.219 0.281 0.03 2.00
3/4 4.62 R13 1.688 0.250 0.344 0.03 2.50
1 4.88 R16 2.000 0.250 0.344 0.03 2.75
1 1/4 5.25 R18 2.375 0.250 0.344 0.03 3.12
1 1/2 6.12 R20 2.688 0.250 0.344 0.03 3.56
2 6.50 R23 3.250 0.312 0.469 0.03 4.25
2 1/2 7.50 R26 4.000 0.312 0.469 0.03 5.00
3 8.25 R31 4.875 0.312 0.469 0.03 5.75
3 1/2 9.00 R34 5.188 0.312 0.469 0.03 6.25
4 10.00 R37 5.875 0.312 0.469 0.03 6.88
5 11.00 R41 7.125 0.312 0.469 0.03 8.25
6 12.50 R45 8.312 0.312 0.469 0.03 9.50
8 15.00 R49 10.625 0.312 0.469 0.03 11.88
10 17.50 R53 12.750 0.312 0.469 0.03 14.00
12 20.50 R57 15.000 0.312 0.469 0.03 16.25
14 23.00 R61 16.500 0.312 0.469 0.03 18.00
16 25.50 R65 18.500 0.312 0.469 0.03 20.00
18 28.00 R69 21.000 0.312 0.469 0.03 22.62
20 30.50 R73 23.000 0.375 0.531 0.06 25.00
24 36.00 R77 27.250 0.438 0.656 0.06 29.50
NOTES
TECHNICAL DATA
1. All dimensions are in inches. 4. For ring joints with lapped flanges in Class 300 and 600,
2. Height of raised portion is equal to the depth of grove ring and groove number R30 are used instead of R31.
3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
R < 0.06 + 0.03, - 0.0;
R > 0.06 ± 0.03
23° (angle) = ½°
149

CLASS 600

Groove
Pipe Depth Width
Size
O.D. P E F R K
1/2 3.75 R11 1.344 0.219 0.281 0.03 2.00
3/4 4.62 R13 1.688 0.250 0.344 0.03 2.50
1 4.88 R16 2.000 0.250 0.344 0.03 2.75
1 1/4 5.25 R18 2.375 0.250 0.344 0.03 3.12
1 1/2 6.12 R20 2.688 0.250 0.344 0.03 3.56
2 6.50 R23 3.250 0.312 0.469 0.03 4.25
2 1/2 7.50 R26 4.000 0.312 0.469 0.03 5.00
3 8.25 R31 4.875 0.312 0.469 0.03 5.75
3 1/2 9.00 R34 5.188 0.312 0.469 0.03 6.25
4 10.75 R37 5.875 0.312 0.469 0.03 6.88
5 13.00 R41 7.125 0.312 0.469 0.03 8.25
6 14.00 R45 8.312 0.312 0.469 0.03 9.50
8 16.50 R49 10.625 0.312 0.469 0.03 11.88
10 20.00 R53 12.750 0.312 0.469 0.03 14.00
12 22.00 R57 15.000 0.312 0.469 0.03 16.25
14 23.75 R61 16.500 0.312 0.469 0.03 18.00
16 27.00 R65 18.500 0.312 0.469 0.03 20.00
18 29.25 R69 21.000 0.312 0.469 0.03 22.62
20 32.00 R73 23.000 0.375 0.531 0.06 25.00
24 37.00 R77 27.250 0.438 0.656 0.06 29.50
TECHNICAL DATA
NOTES
1. All dimensions are in inches. 4. For ring joints with lapped flanges in Class 300 and 600,
2. Height of raised portion is equal to the depth of grove ring and groove number R30 are used instead of R31.
3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
R < 0.06 + 0.03, - 0.0;
R > 0.06 ± 0.03
23° (angle) = ½°
150

TEL: 708/594-1700
FAX: 708/458-0106
CLASS 900

Groove
Pipe Depth Width
Size
O.D. P E F R K
1/2 4.75 R12 1.562 0.250 0.344 0.03 2.38
3/4 5.12 R14 1.750 0.250 0.344 0.03 2.62
1 5.88 R16 2.000 0.250 0.344 0.03 2.81
1 1/4 6.25 R18 2.375 0.250 0.344 0.03 3.19
1 1/2 7.00 R20 2.688 0.250 0.344 0.03 3.62
2 8.50 R24 3.750 0.312 0.469 0.03 4.88
2 1/2 9.62 R27 4.250 0.312 0.469 0.03 5.38
3 9.50 R31 4.875 0.312 0.469 0.03 6.12
4 11.50 R37 5.875 0.312 0.469 0.03 7.12
5 13.75 R41 7.125 0.312 0.469 0.03 8.50
6 15.00 R45 8.312 0.312 0.469 0.03 9.50
8 18.50 R49 10.625 0.312 0.469 0.03 12.12
10 21.50 R53 12.750 0.312 0.469 0.03 14.25
12 24.00 R57 15.000 0.312 0.469 0.03 16.50
14 25.25 R62 16.500 0.438 0.656 0.06 18.38
16 27.75 R66 18.500 0.438 0.656 0.06 20.62
18 31.00 R70 21.000 0.500 0.781 0.06 23.38
20 33.75 R74 23.000 0.500 0.781 0.06 25.50
24 41.00 R78 27.250 0.625 1.062 0.09 30.38
NOTES
TECHNICAL DATA

3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
R < 0.06 + 0.03, - 0.0;
R > 0.06 ± 0.03
23° (angle) = ½°
4. Use Class 1500 in sizes NPS ½ to NPS 2 ½ for Class 900.
151

CLASS 1500

Groove
Pipe Depth Width
Size
O.D. P E F R K
1/2 4.75 R12 1.562 0.250 0.344 0.03 2.38
3/4 5.12 R14 1.750 0.250 0.344 0.03 2.62
1 5.88 R16 2.000 0.250 0.344 0.03 2.81
1 1/4 6.25 R18 2.375 0.250 0.344 0.03 3.19
1 1/2 7.00 R20 2.688 0.250 0.344 0.03 3.62
2 8.50 R24 3.750 0.312 0.469 0.03 4.88
2 1/2 9.62 R27 4.250 0.312 0.469 0.03 5.38
3 10.50 R35 5.375 0.312 0.469 0.03 6.62
4 12.25 R39 6.375 0.312 0.469 0.03 7.62
5 14.75 R44 7.625 0.312 0.469 0.03 9.00
6 15.50 R46 8.312 0.375 0.531 0.06 9.75
8 19.00 R50 10.625 0.438 0.656 0.06 12.50
10 23.00 R54 12.750 0.438 0.656 0.06 14.62
12 26.50 R58 15.000 0.562 0.906 0.06 17.25
14 29.50 R63 16.500 0.625 1.062 0.09 19.25
16 32.50 R67 18.500 0.688 1.188 0.09 21.50
18 36.00 R71 21.000 0.688 1.188 0.09 24.12
20 38.75 R75 23.000 0.688 1.312 0.09 26.50
24 46.00 R79 27.250 0.812 1.438 0.09 31.25
NOTES
TECHNICAL DATA

3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
R < 0.06 + 0.03, - 0.0;
R > 0.06 ± 0.03
23° (angle) = ½°
152

TEL: 708/594-1700
FAX: 708/458-0106
CLASS 2500

Groove
Pipe Depth Width
Size
O.D. P E F R K
1/2 5.25 R13 1.688 0.250 0.344 0.03 2.56
3/4 5.50 R16 2.000 0.250 0.344 0.03 2.88
1 6.25 R18 2.375 0.250 0.344 0.03 3.25
1 1/4 7.25 R21 2.844 0.312 0.469 0.03 4.00
1 1/2 8.00 R23 3.250 0.312 0.469 0.03 4.50
2 9.25 R26 4.000 0.312 0.469 0.03 5.25
2 1/2 10.50 R28 4.375 0.375 0.531 0.06 5.88
3 12.00 R32 5.000 0.375 0.531 0.06 6.62
4 14.00 R38 6.188 0.438 0.656 0.06 8.00
5 16.50 R42 7.500 0.500 0.781 0.06 9.50
6 19.00 R47 9.000 0.500 0.781 0.06 11.00
8 21.75 R51 11.000 0.562 0.906 0.06 13.38
10 26.50 R55 13.500 0.688 1.188 0.09 16.75
12 30.00 R60 16.000 0.688 1.312 0.09 19.50
NOTES
3. Tolerances:
E (depth) + 0.016, - 0.0
F (width) ± 0.008
TECHNICAL DATA
R < 0.06 + 0.03, - 0.0;

R > 0.06 ± 0.03
23° (angle) = ½°
153

weld end preparations
Bevel for weldneck flanges
Bevel for Wall Thicknesses (T) Bevel for Wall Thicknesses (T)
from 0.19 in. to 0.88 in. Inclusive Greater Than 0.88 in.
¼"
¼" min.
min.
1:3 max. slope
1:3 max. slope
37 ½° 10° ± 2 ½°
± 2 ½°
45° max. 0.12 min. radius 45° max.
37 ½° ± 2 ½°
T
T ¾"
0.06" ± 0.03"
O.D. O.D. 0.06" ± 0.03"
X X
I.D. I.D.
O.D. = Outside Diameter of pipe

I.D. = Inside Diameter of pipe
T = Wall thickness of pipe
X = diameter of hub
NOTES
2. When the thickness of the hub at the bevel is greater than that of the pipe
to which the flange is joined and the additional thickness is provided on the
outside diameter, a taper weld having a slope not exceeding 1 to 3 may be
employed or, alternatively, the greater outside diameter may be tapered at the
same maximum slope or less, from a point on the welding bevel equal to the
outside diameter of the mating pipe. Similarly, when the greater thickness is
provided on the inside of the flange, it shall be taper-bored from the welding
end at the slope not exceeding 1 to 3. When flanges covered by this Standard
are intended for services with light wall, higher strength pipe, the thickness of
the hub at the bevel may be greater than that of the pipe to which the flange is
TECHNICAL DATA
joined. Under these conditions, a single taper hub may be provided, and the
outside diameter of the hub at the base (dimension X) may also be modified.
The additional thickness may be provided on either inside or outside or partially
on each side, but the total additional thickness shall not exceed one-half times
the nominal wall thickness of intended mating pipe. See page 155.
3. The hub transition from the outside diameter to the X diameter shall fall within the
maximum and minimum envelope outlined by the 1:3 max. slope and the
dashed line.
4. For welding end dimensions, refer to ASME B16.25.
154

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com weld end preparations
joining buttwelding fittings to pipe
of equal or lesser wall thickness
T1 T2
3/32" MAX.
T1
T2
1/2 T1 MAX.
T1
T2
1/2 T1 MAX.
NOTES
1. Buttwelding fittings can be joined to pipe of lesser wall thickness with proper end
preparation and joint design.
2. Above diagrams and recommendations that follow apply to components with ends
originally prepared as standard 37 ½º or 30º degree bevels and where the wall thickness
of the thicker end to be joined does not exceed 1 ½ times the thinner (pipe) end.
3. T he nominal thickness T1 (pipe) and T2 (fitting) shall comply with the design requirements
of the applicable section of the ASME B31 Code For Pressure Piping.
4. Where the total nominal offset (T2-T1) does not exceed 3/32" and full penetration and
bonding is obtained during welding, no special treatment is required [see (A)].
5. When the internal offset exceeds 3/32", taper cut in accordance with (B) ...or taper
weld in accordance with (C).
TECHNICAL DATA
6. When joining ends with materials of unequal minimum specified yield strengths
(or unequal allowable stress), the deposited weld metal shall have mechanical properties
at least equal to those of the higher strength (pipe) end.
7. For treatments of ends with unequal external diameters and/or where T2 is thicker than
1 1/2 times T1, refer to the applicable section of the ASME Code, e., B31.4 or B31.8 or B16.9.
155

thread standard practices
American Standard
Taper Pipe Threads
NPT Basic Dimensions
Hand-Tight Engagement Effective Thread-External Length

Pitch L1 Plane to L2 Plane
Outside Diameter at External Thread
Threads Pitch of Length2 Length4
Pipe Diameter Beginning (L1–L2)
Per Inch Thread
Size of Pipe of External Diameter3 Diameter3
Thread Inch Threads Inch Threads Inch Thread
O.D. n P E0 L1 L1 E1 L2 L2 E2 L1–L2 L1–L2

1/16 0.313 27.0 0.03704 0.27118 0.160 4.32 0.28118 0.2611 7.05 0.28750 0.1011 2.73
1/8 0.405 27.0 0.03704 0.36351 0.162 4.36 0.37360 0.2639 7.12 0.38000 0.1024 2.76
1/4 0.540 18.0 0.05556 0.47739 0.228 4.10 0.49163 0.4018 7.23 0.50250 0.1740 3.13
3/8 0.675 18.0 0.05556 0.61201 0.240 4.32 0.62701 0.4078 7.34 0.63750 0.1678 3.02
1/2 0.840 14.0 0.07143 0.75843 0.320 4.48 0.77843 0.5337 7.47 0.79179 0.2137 2.99
3/4 1.050 14.0 0.07143 0.96768 0.339 4.75 0.98887 0.5457 7.64 1.00179 0.2067 2.89
1 1.315 11.5 0.08696 1.21363 0.400 4.60 1.23863 0.6828 7.85 1.25630 0.2828 3.25
1 1/4 1.660 11.5 0.08686 1.55713 0.420 4.83 1.58338 0.7068 8.13 1.60130 0.2868 3.30
1 1/2 1.900 11.5 0.08686 1.79609 0.420 4.83 1.82234 0.7235 8.32 1.84130 0.3035 3.49
2 2.375 11.5 0.08686 2.26902 0.436 5.01 2.29627 0.7565 8.70 2.31630 0.3205 3.69
2 1/2 2.875 8.0 0.12500 2.71953 0.682 5.46 2.76216 1.1375 9.10 2.79062 0.4555 3.64
3 3.500 8.0 0.12500 3.34062 0.766 6.13 3.38850 1.2000 9.60 3.41562 0.4340 3.47
3 1/2 4.000 8.0 0.12500 3.83750 0.821 6.57 3.88881 1.2500 10.00 3.91562 0.4290 3.43
4 4.500 8.0 0.12500 4.33438 0.844 6.75 4.38712 1.3000 10.40 4.41562 0.4560 3.65
5 5.563 8.0 0.12500 5.39073 0.937 7.50 5.44929 1.4063 11.25 5.47862 0.4693 3.75
6 6.625 8.0 0.12500 6.44609 0.958 7.66 6.50597 1.5125 12.10 6.54062 0.5545 4.44
8 8.625 8.0 0.12500 8.43359 1.063 8.50 8.50003 1.7125 13.70 8.54062 0.6495 5.20
10 10.750 8.0 0.12500 10.54531 1.210 9.68 10.62094 1.9250 15.40 10.66562 0.7150 5.72
TECHNICAL DATA
12 12.750 8.0 0.12500 12.53281 1.360 10.88 12.61781 2.1250 17.00 12.66562 0.7650 6.12
14 14.000 8.0 0.12500 13.77500 1.562 12.50 13.87262 2.2500 18.00 13.91562 0.6880 5.50
16 16.000 8.0 0.12500 15.76250 1.812 14.50 15.87575 2.4500 19.60 15.91562 0.6380 5.10
18 18.000 8.0 0.12500 17.75000 2.000 16.00 17.8750 2.6500 21.20 17.91562 0.6500 5.20
20 20.000 8.0 0.12500 19.73750 2.125 17.00 19.87031 2.8500 22.80 19.91562 0.7250 5.80
24 24.000 8.0 0.12500 23.71250 2.375 19.00 23.86094 3.2500 26.00 23.91562 0.8750 7.00
156

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com thread standard practices
INSERT PLUG GAUGE

UNTIL NOTCH IS FLUSH
PLUG GAUGE
WITH FIRST THREAD,
STANDARD TOLERANCE
IS ± ONE THREAD
Wrench Makeup
Length for Internal Thread 7 Vanish Nominal
Overall8 Complete Basic Minor
Thread Length Height of Increase in Diameter
Length (L3) External Threads
External Thread Diameter at Small End Pipe
Diameter Thread Thread of Pipe Size
Inch Thread Inch Thread Length Diameter (0.0625/n)
L3 L3 E3 V V L4 L5 E5 h K0
0.1111 3 0.26424 0.1285 3.47 0.3896 0.1870 0.28287 0.02963 0.00231 0.2416 1/16
0.1111 3 0.35656 0.1285 3.47 0.3924 0.1898 0.37537 0.02963 0.00231 0.3339 1/8
0.1667 3 0.46697 0.1928 3.47 0.5946 0.2907 0.49556 0.04444 0.00347 0.4329 1/4
0.1667 3 0.60160 0.1928 3.47 0.6006 0.2967 0.63056 0.04444 0.00347 0.5676 3/8
0.2143 3 0.74504 0.2478 3.47 0.7815 0.3909 0.78286 0.05714 0.00446 0.7013 1/2
0.2143 3 0.95429 0.2478 3.47 0.7935 0.4029 0.99286 0.05714 0.00446 0.9105 3/4
0.2609 3 1.19733 0.3017 3.47 0.9845 0.5089 1.24543 0.06957 0.00543 1.1441 1
0.2609 3 1.54083 0.3017 3.47 1.0085 0.5329 1.59043 0.06957 0.00543 1.4876 1 1/4
0.2609 3 1.77978 0.3017 3.47 1.0252 0.5496 1.83043 0.06957 0.00543 1.7265 1 1/2
0.2609 3 2.25272 0.3017 3.47 1.0582 0.5826 2.30543 0.06957 0.00543 2.1995 2
0.2500 2 2.70391 0.4337 3.47 1.5712 0.8875 2.77500 0.10000 0.00781 2.6195 2 1/2
0.2500 2 3.32500 0.4337 3.47 1.6337 0.9500 3.40000 0.10000 0.00781 3.2406 3
0.2500 2 3.82188 0.4337 3.47 1.6837 1.0000 3.90000 0.10000 0.00781 3.7375 3 1/2
0.2500 2 4.31875 0.4337 3.47 1.7337 1.0500 4.40000 0.10000 0.00781 4.2344 4
0.2500 2 5.37511 0.4337 3.47 1.8400 1.1563 5.46300 0.10000 0.00781 5.2907 5
0.2500 2 6.43047 0.4337 3.47 1.9462 1.2625 6.52500 0.10000 0.00781 6.3461 6
0.2500 2 8.41797 0.4337 3.47 2.1462 1.4625 8.52500 0.10000 0.00781 8.3336 8
0.2500 2 10.52969 0.4337 3.47 2.3587 1.6750 10.65000 0.10000 0.00781 10.4453 10
TECHNICAL DATA
0.2500 2 12.51719 0.4337 3.47 2.5587 1.8750 12.65000 0.10000 0.00781 12.4328 12
0.2500 2 13.75938 0.4337 3.47 2.6837 2.0000 13.90000 0.10000 0.00781 13.6750 14
0.2500 2 15.74688 0.4337 3.47 2.8837 2.2000 15.90000 0.10000 0.00781 15.6625 16
0.2500 2 17.73438 0.4337 3.47 3.0837 2.4000 17.90000 0.10000 0.00781 17.6500 18
0.2500 2 19.72188 0.4337 3.47 3.2837 2.6000 19.90000 0.10000 0.00781 19.6375 20
0.2500 2 23.69688 0.4337 3.47 3.6837 3.0000 23.90000 0.10000 0.00781 23.6125 24
157

thread standards
CLASS 150 STANDARD WITH 1/16" RAISED FACE CLASS 300 – 2500 STANDARD WITH 1/16" RAISED FACE
Thread Length (Inches)

Pipe Size
150 300 600 900 1500 2500
1/2 0.62 0.62 0.62 0.88 0.88 1.12
3/4 0.62 0.62 0.62 1.00 1.00 1.25
1 0.69 0.69 0.69 1.12 1.12 1.38
1 1/4 0.81 0.81 0.81 1.19 1.19 1.50
1 1/2 0.88 0.88 0.88 1.25 1.25 1.75
2 1.00 1.12 1.12 1.50 1.50 2.00
2 1/2 1.12 1.25 1.25 1.88 1.88 2.25
3 1.19 1.25 1.38 1.62
3 1/2 1.25 1.44 1.56
4 1.31 1.44 1.62 1.88
5 1.44 1.69 1.88 2.12
6 1.56 1.81 2.00 2.25
8 1.75 2.00 2.25 2.50
10 1.94 2.19 2.56 2.81
12 2.19 2.38 2.75 3.00
14 2.25 2.50 2.88 3.25
16 2.50 2.69 3.06 3.38
18 2.69 2.75 3.12 3.50
20 2.88 2.88 3.25 3.62
24 3.25 3.25 3.62 4.00
30
36
42
48
NOTES
2. Weldbend flanges are tapped with American
TECHNICAL DATA
National Standard taper pipe threads. These threads

have longer thread lengths in proportion to the flange
thickness of elevated temperatures.
3. The gauging notch of the plug gauge should come flush
with a manufacturing tolerance + one turn.
158

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com method for calculating bolt lengths
The following formulas were used in establishing length for flanges on pages 85 - 97.
They are given for convenience in determining lengths not given in the tables.
LCSB (See Note 1) = A + n
LCMB (See Note 1) = B + n
Where:
A = 2(C + t +d) + G + F - a, (i.e. stud-bolt length LSSB = Specified stud-bolt length (effective thread
exclusive of negative tolerance n). length, excluding end points) which is LCSB
rounded off to the next larger 0.25 in.
B = 2(C + t) + d + G + F + p - a, (i.e. machine bolt increment; see Figure 1.
length exclusive of negative length tolerance n).
a = Zero, except where the small female face is
C = Minimum flange thickness. on the end of pipe, a = 0.19 in.
F = Total height of facings or depth of ring-joint d = Heavy nut thickness (equals nominal bolt
groove for both flanges, see "F" Values on diameter, see ASME B18.2.2).
page 160.
n = Negative tolerance on bolt length.
G = 0.12 in. (3.2 mm) gasket thickness for
raised face, M & F and T & G flanges; p = Allowance for height of point of machine bolt
also approximate distance between (= 1.5 times thread pitch).
ring-joint flanges.
t = Plus tolerance for flange thickness.
LCMB = Calculated machine bolt length as measured
from underside of head to end of point.
LSMB = Specified machine bolt length (from

under head to end, including end point)
which is LCMB rounded off to the next larger
0.25 in. increment; see Figure 2.
NOTES
1. For lapped joints calculate stud-bolt and machine bolt lengths as follows:
L = (A + pipe thickness for each lap) + n

For ring-joint CSB
groove facing L = (B + pipe thickness for each lap) + n
CMB
TECHNICAL DATA
For other L = A - F + (Table C-1 thickness) + n

than ring-joint CSB
groove facing L = B - F + (Table C-1 thickness) + n
CMB
2. The equations used on this page are for calculated bolt

lengths established to assure full thread engagement of heavy
hexagon nuts when worst case tolerances occur on all relevant
dimensions of the flanged joint.
159

method for calculating bolt lengths
“F” VALUES
Total Height of Facings or

Depth of Ring-Joint Groove for Both Flanges “F”
Flanged
Joint
Type of Flange Facing
Class
M&F
0.06 in. 0.25 in. Ring Joint
T&G
0.12 in. 0.50 in. 0.25 in. 2 x groove depth
150 & 300
400 to 1500
“n” VALUES
Length Negative Tolerance on Bolt Lengths “n”
Stud Bolt A
or 0.06 in., for lengths up to 12 in. incl.
[A+(pipe thickness for each lap)] 0.12 in., for lengths over 12 in. to 18 in. incl.
or 0.25 in., for lengths over 18 in. incl.
[A-F+(Table C-1 thickness)]
Machine Bolt B
or For “n” values
[B+(pipe thickness for each lap)] use negative length tolerances
or per ASME B18.2.1
[B-F+(Table C-1 thickness)]
Table C-1: THICKNESS FOR LAPPED JOINTS
Lap Combination Class 150 Thru 2500 Flanges
For Lapped to 0.06 in. Raised Face, male face on flange One Lap and 0.06 in.
For Lapped to Lapped Both Laps
For Lapped to 0.25 in. Male Face on Flange One Lap and 0.25 in.
For Lapped to Female Face on Flange One Lap not less than 0.25 in.
TECHNICAL DATA
For Male in Lap to Female in Lap 2 x pipe wall with Lap for Male not less than 0.25 in.
160

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com pressure-temperature ratings for flanges
Weldbend manufactures flanges for Class 125, 150, 300, 600, 900, 1500 and 2500.
Note that the table specifically rates carbon steel products within the temperatures listed.
Pressure – Temperature Ratings for Group 1.1 Materials
Nominal
Forgings Castings Plates
Designation
C–Si 1A 105 (1) A 216 Gr. WCB (1) 3A 515 Gr. 70 (1)
C–Mn–Si A 350 Gr. LF2 (1) A 516 Gr. 70 (1), (2)
C–Mn–Si–V A 350 Gr. LF6 Cl. 1 (4) A 537 CI. 1 (3)
3 1/2 NI A 350 Gr. LF 3
Rating (Carbon Steel)
Temperature Working Pressure in psig by Classes

in °F
125 150 300 600 900 1500 2500
-20 to 100 * 285 740 1480 2220 3705 6170
200 * 260 680 1360 2035 3395 5655
300 * 230 655 1310 1965 3270 5450
400 * 200 635 1265 1900 3170 5280
500 * 170 605 1205 1810 3015 5025
600 * 140 570 1135 1705 2840 4730
650 * 125 550 1100 1650 2745 4575
700 * 110 530 1060 1590 2655 4425
750 * 95 505 1015 1520 2535 4230
800 * 80 410 825 1235 2055 3430
850 * 65 320 640 955 1595 2655
900 * 50 230 460 690 1150 1915
950 * 35 135 275 410 685 1145
1000 * 20 85 170 255 430 715
*There is no standard for Class 125 as it is applicable to Cast Iron Standard ASME B16.1. Class 125 flanges are wide in
face and used for connections to cast steel valves or equipment containing flanged ends made to Cast Iron Standard
dimensions. Carbon steel bolting is intended and alloy studs should be avoided. Class 125 flanges are identical with
Class E AWWA.
TECHNICAL DATA
NOTES
1. Upon prolonged exposure to temperatures above 800°F,
the carbide phase of steel may be converted to graphite.
Permissible, but not recommended for prolonged use
above 800°F.
2. Not to be used over 850°F
161

useful formulas
MULTIPLY BY TO OBTAIN MULTIPLY BY TO OBTAIN
Atmospheres (Std.) Feet / minute 0.5080 cm. / sec.

760 mm. of Mercury @ 32º F 14.696 lbs. / sq. in. Feet / minute 0.01667 ft. / sec.
Atmospheres 76.0 cm. of Mercury Feet / minute 0.01829 km. / hr.
Atmospheres 29.13 in. of Mercury Feet / minute 0.3048 m. / min.
Atmospheres 33.905 ft. of water Feet / minute 0.01136 mi. / hr.
Atmospheres 1.0325 kgs. / sq. cm.
Atmospheres 14.70 lbs. / sq. in. Fluid Ounces (fl. oz.) 1.805 cu. in.
Fluid Ounces 0.02957 L
British Thermal Units (BTU) 0.2520 kgs. - cal.
British Thermal Units 778.3 ft. - lbs. Fluid Ounces / square inch 0.0625 lbs. / sq. in.
British Thermal Units 0.0003931 hph. Fluid Ounces / square inch 1.73 in. of water
BTU / minute 12.969 ft. - lbs. / sec. Foot / pounds 0.001286 BTU
BTU / minute 0.02358 HP
Gallons (gal.) 3785 cu. cm.
BTU / minute 0.01758 kW
Gallons 0.1337 cu. ft.
BTU / minute 17.5784 W
Gallons 231 cu. in.
Calorie (cal.) 0.003966 BTU Gallons 128 fl. oz.
Gallons 3.785 L
Centimeter (cm.) 0.3937 in.
Gallons of water 8.35 lbs. / water @ 60º F
Centimeter 0.03280 ft.
Centimeter 0.01 m.
Horsepower (HP) 42.41 BTU / min.
Centimeter 10 mm.
Horsepower 33,000 ft. - lbs. / min.
Horsepower 550 ft. - lbs. / sec.
Centimeters of Mercury 0.01315 Atmospheres
Horsepower 0.7457 kW 1060 W
Centimeters of Mercury 0.4461 ft. of water
Horsepower 745.7 W
Centimeters of Mercury 136.0 kgs. / sq. m.
Centimeters of Mercury 27.85 lbs. / sq. ft.
Boiler Horsepower (BHP) 33,520 BTU / hr.
Centimeters of Mercury 0.1934 lbs. / sq. in.
Boiler Horsepower 9,803 kW - hr.
Cubic feet (cu. ft.) 2.832 x 104 cu. cm. Horsepower - hours (hph) 2544 BTU
Cubic feet 1728 cu. in. Horsepower - hours 0.7457 kW - hr.
Cubic feet 0.02832 cu. m.
Cubic feet 0.03737 cu. yd. Inches (in.) 2,540 cm.
Cubic feet 7.48052 gal. Inches 25.4 mm.
Inches 0.0254 m.
Cubic feet / minute 472.0 cu. cm. / sec. Inches 0.0833 ft.
Cubic feet / minute 0.1247 gal. / sec.
Inches of Mercury 0.03342 Atmospheres
Cubic foot of water 62.4 lbs. @ 60º F Inches of Mercury 1.133 ft. of water
Inches of Mercury 13.57 in. of water
TECHNICAL DATA
Feet (ft.) 30.48 cm. Inches of Mercury 70.73 lbs. / sq. ft.
Feet 12 in. Inches of Mercury 0.4912 lbs. / sq. in.
Feet 0.3048 m.
Feet 0.33 yd. Inches of water 0.002458 Atmospheres
Inches of water 0.07355 in. of Mercury
Feet of water 0.02950 Atmospheres Inches of water 0.5781 oz. / sq. in.
Feet of water 0.8226 in. of Mercury Inches of water 5.202 lbs. / sq. ft.
Feet of water 0.03048 kgs. / sq. cm. Inches of water 0.03613 lbs. / sq. in.
Feet of water 62.43 lbs. / sq. ft.
Feet of water 0.4355 lbs. / sq. in.
162

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com useful formulas
MULTIPLY BY TO OBTAIN MULTIPLY BY TO OBTAIN
Kilowatts (kW) 56.87 BTU / min. Therm 100,000 BTU

Kilowatts 1.341 HP
Kilowatts 1000 W Ton of Refrigeration 12,000 BTU / hr.
Kilowatt - hours 3.415 BTU Tons (long) 2240 lbs.
Liters (L) 0.2642 gal. Tons (short) 2000 lbs.

Liters 2.113 pt. (liq.)
Liters 1.057 qt. (liq.) Watts (W) 3.412 BTU
Watts 0.05692 BTU / min.
Meters (m.) 1.805 cu. in. Watts 44.26 ft. - lbs. / min.
Meters 3.281 ft. Watts 0.7376 ft. - lbs. / sec.
Meters 39.37 in. Watts 0.001341 HP
Meters 1000 mm. Watts 0.001 kW
Meters 1.094 yd.
Watts - hours 3.415 BTU / hr.
Pints (pt.) 0.4732 L Watts - hours 2655 ft. - lbs.
Watts - hours 0.001341 hph.
Pounds (avoir) 16 oz. Watts - hours 0.001 kW - hr.
Pounds of water 0.01602 cu. ft. 746 W = 1HP

Pounds of water 27.68 cu. in.
Pounds of water 0.1198 gal. Additional Unit Abbreviations:
kilograms = kgs.
Pounds / square foot 0.01602 ft. of water quarts = qt.
Pounds / square foot 0.006945 lbs. / sq. in. miles = mi.
millimeters = mm.
Pounds / square inch 0.06804 Atmospheres yards = yd.
Pounds / square inch 2.307 ft. of water minute = min.
Pounds / square inch 2.036 in. of Mercury cubic = cu.
Pounds / square inch 27.68 in. of water kilometers = km.
absolute = abs.
Temp. (ºC) + 273 1 abs. temp. (ºC) hours = hr.
Temp. (ºC) + 273 1.8 temp. (ºF)
Temp. (ºC) + 273 1 abs. temp. (ºF)
Temp. (ºC) + 273 5/9 temp. (ºC)
Calculation of Transition Slope

TECHNICAL DATA
163

useful formulas
Where:
A = Area; A1 = Surface area of solids;
V = Volume; C = Circumference
Rectangle Ellipse
A=WxL A = 3.142 x A x B
C = 6.283 x A2 + B2
2
Parallelogram
A=HxL Rectangular Solid
A1 = 2[W x L + L x H + H x W]
V=WxLxH
Trapezoid L1
L1 + L2
A=Hx 2 Cone S
L2 A1 = 3.142 x R x S + 3.142 x R x R
V = 1.047 x R x R x H
Triangle
WxH
A= 2
Cylinder
A1 = 6.283 x R x H + 6.283 x R x R
V = 3.142 x R x R x H
Circle
A = 3.142 x R x R
C = 3.142 x D Elliptical Tanks
D A2 + B2
R= A1 = 6.283 x
2 2 x H + 6.283 x A x B
D=2xR V = 3.142 x A x B x H
Sector of Circle
3.142 x R x R x a Sphere
A=
TECHNICAL DATA
360 A1 = 12.56 x R x R
L = .01745 x R x R x a V = 4.188 x R x R x R
a= L
.01745 x R
For above containers:

Capacity in gallons = V / 231 when V is cubic inches
Capacity in gallons = 7.48 x V when V is cubic feet.
164

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com conversion chart
Equivalent Pressure Equivalent Pressure

Inches Per Square Inch Inches Per Square Inch
Water Mercury Pounds Ounces Water Mercury Pounds Ounces
0.10 0.007 0.0036 0.058 8.00 0.588 0.2890 4.620

0.20 0.015 0.0072 0.115 9.00 0.662 0.3250 5.200
0.30 0.022 0.0108 4.173 10.00 0.735 0.3610 5.770
0.40 0.029 0.0145 0.231 11.00 0.809 0.3970 6.340
0.50 0.037 0.0181 0.289 12.00 0.883 0.4330 6.920
0.60 0.044 0.0217 0.346 13.00 0.956 0.4690 7.500
0.70 0.051 0.0253 0.404 13.60 1.000 0.4910 7.860
0.80 0.059 0.0289 0.462 13.90 1.022 0.5000 8.000
0.90 0.066 0.3250 0.520 14.00 1.030 0.5050 8.080
1.00 0.074 0.0360 0.577 15.00 1.103 0.5420 8.700
1.36 0.100 0.0490 0.785 16.00 1.177 0.5780 9.200
1.74 0.128 0.0670 1.000 17.00 1.250 0.6140 9.800
2.00 0.147 0.0720 1.150 18.00 1.324 0.6500 10.400
2.77 0.203 0.1000 1.600 19.00 1.397 0.6860 10.900
3.00 0.221 0.1090 1.730 20.00 1.471 0.7220 11.500
4.00 0.294 0.1440 2.310 25.00 1.839 0.9030 14.400
5.00 0.368 0.1810 2.890 27.20 2.000 0.9750 15.700
6.00 0.441 0.2170 3.460 27.70 2.037 1.0000 16.000
7.00 0.515 0.2530 4.040
Compression Ratio
or
Pressure Ratio
ABSOLUTE DISCHARGE PRESSURE

= PRESSURE RATIO
ABSOLUTE SUCTION PRESSURE
TECHNICAL DATA
GAUGE PRESSURE + 14.75 LBS = ABSOLUTE PRESSURE
165

metric system conversions
MEASUREMENT EQUIVALENTS — LENGTH
Inches to Millimeters Millimeters to Inches

1 in. = 25.4 mm. 1 mm. = 0.0393700787 in.
Inches Millimeters Millimeters Inches
0.50 12.700 0.50 0.0200
1.00 25.400 1.00 0.0393
1.50 38.100 1.50 0.0591
2.00 50.800 2.00 0.0787
2.50 63.500 2.50 0.0984
3.00 76.200 3.00 0.1181
3.50 88.900 3.50 0.1378
4.00 101.600 4.00 0.1575
4.50 114.300 4.50 0.1772
5.00 127.000 5.00 0.1970
5.50 139.700 5.50 0.2165
6.00 152.400 6.00 0.2362
6.50 165.100 6.50 0.2559
7.00 177.800 7.00 0.2760
7.50 190.500 7.50 0.2953
8.00 203.200 8.00 0.3150
8.50 215.900 8.50 0.3347
9.00 228.600 9.00 0.3543
9.50 241.300 9.50 0.3740
10.00 254.000 10.00 0.3937
10.50 266.700 20.00 0.7874
11.00 279.400 30.00 1.1811
11.50 292.100 40.00 1.5748
12.00 304.800 50.00 1.9685
Feet to Meters Meters to Feet

1 ft. = 0.3048 m. 1 m. = 3.2808398895 ft.
Feet Meters Meters Feet
1 0.3048 1 3.2808
2 0.6096 2 6.5617
3 0.9144 3 9.8425
4 1.2192 4 13.1234
5 1.5240 5 16.4042
6 1.8288 6 19.6850
7 2.1336 7 22.9659
8 2.4384 8 26.2467
9 2.7432 9 29.5276
10 3.0480 10 32.8084
11 3.3528 11 36.0892
12 3.6576 12 39.3701
13 3.9624 13 42.6509
TECHNICAL DATA
14 4.2672 14 45.9318
15 4.5720 15 49.2126
20 6.0960 20 65.6168
30 9.1440 30 98.4252
40 12.1920 40 131.2336
50 15.2400 50 164.0420
60 18.2880 60 196.8504
70 21.3360 70 229.6588
80 24.3840 80 262.4672
90 27.4320 90 295.2756
100 30.4800 100 328.0840
166

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com metric system conversions
KELVIN SCALE TEMPERATURE
Another temperature scale used with the metric system

is called the Kelvin scale. It was named after Lord Kelvin,
a great British physicist.
As shown below, the starting or zero point on the Kelvin

scale is absolute zero. Absolute zero is the lowest theoretical
temperature that a gas can reach.
Notice that the difference between the freezing and the

boiling temperatures of water is 100 Celsius units and also
100 Kelvin units. The only difference between the two scales
is that the Kelvin scale has a “head start” of 273.15 units.
You can change a Celsius reading (c) to a Kelvin reading (k)

as follows:
k = c + 273.15 72ºC = ? ºK
k = 72 + 273.15
k = 345.15
72ºC = 345.15ºK
You can change a Kelvin reading to a

Celsius reading as follows:
c = k – 273.15 250ºK = ? ºC
c = 250 – 273.15
c = –23.15
250ºK = –23.15ºC
By laying the edge of a ruler or paper

perpendicular to the scales shown here,
you can estimate equivalent temperatures
on all three scales.
TECHNICAL DATA
167

Material Test Report Identification
FITTINGS
Manufacturer Heat Codes*

of Product
Size Material
Specification
Wall Thickness
Description of designations:
WPB - ASTM A234 WPB
STD - Standard Weight
USA - NOTE: If Weldbend marks their fittings "Made in USA", it is your assurance
that both the starting material and the complete production is of USA origin.
*All heat codes follow the material specification marking.
Weldbend weld fittings are permanently identified by die marking to designate:

As seen in illustrated example:
1. Manufacturer [ ] The identification on each Weldbend weld fitting is

your assurance that the fitting has successfully passed
2. Size [12] inspection and quality control, and that the accurate
TECHNICAL DATA
record of chemical and physical properties of the steel

3. Wall Thickness [STD] from which the fitting was made is fully traceable.
4. Material Specification [WPB]

5. Heat Codes [442815]
168

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com Material Test Report Identification
FLANGES
Manufacturer
Production
of Product
Code (Optional)
Heat Codes*
Size
Material
Specification
Class Bore Dimensional
(If applicable) Specification
Description of designations:
150 - Class 150 (Weld Neck and Socket Weld Only)
USA - NOTE: If Weldbend marks their fittings "Made in USA", it is your assurance
that both the starting material and the complete production is of USA origin.
*All heat codes follow the material specification marking.
Weldbend flanges are permanently identified by die marking to designate:

As seen in illustrated example:
1. Manufacturer [ ] The identification on each Weldbend weld flange is
your assurance that the flange has successfully passed
2. Size [5] inspection and quality control, and that the accurate
TECHNICAL DATA
record of chemical and physical properties of the steel

3. Class [150] from which the flange was made is fully traceable.
4. Bore (If applicable) [XSB]
5. Dimensional Specification [B16.5]
6. Material Specification [A105/SA105]
7. Heat Codes [MOF]
8. Production Code (Optional) [J02]
169

TORQUE REQUIRED TO PRODUCE INDICATED BOLT STRESS
TORQUE REQUIRED TO PRODUCE INDICATED BOLT STRESS
BOLT Bolt Diameters

STRESS MEASURED IN
(PSI) 1/4 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 1
Ft. - Lbs. 0.1 0.3 0.4 0.7 1 1.5 2 3 5 8
1,000
In. - Lbs. 2 3 5 8 12 18 24 40 64 98
Ft. - Lbs. 0.3 0.5 0.8 1.3 2 3 4 7 11 16
2,000
In. - Lbs. 3 6 10 16 24 36 48 80 128 196
Ft. - Lbs. 0.4 0.8 1 2 3 4.5 6 10 16 25
3,000
In. - Lbs. 5 10 14 24 36 54 72 120 192 294
Ft. - Lbs. 0.5 1 2 3 4 6 8 13 21 32
4,000
In. - Lbs. 6 13 19 32 48 72 96 160 256 392
Ft. - Lbs. 0.7 1 2 3 5 8 10 17 27 41
5,000
In. - Lbs. 8 16 24 40 60 90 120 200 320 490
Ft. - Lbs. 0.8 2 2 4 6 9 12 20 32 49
6,000
In. - Lbs. 5 10 14 24 36 54 144 240 384 588
Ft. - Lbs. 1 2 3 5 7 11 14 23 37 57
7,000
In. - Lbs. 11 22 34 56 84 126 168 280 448 686
Ft. - Lbs. 1 2 3 5 8 12 16 27 65 65
8,000
In. - Lbs. 13 26 38 64 96 144 192 320 784 784
Ft. - Lbs. 1 2 4 6 9 14 18 30 48 74
9,000
In. - Lbs. 14 29 43 72 108 162 216 360 576 —
Ft. - Lbs. 1 3 4 7 10 15 20 33 53 82
10,000
In. - Lbs. 16 32 48 80 120 180 240 400 640 —
Ft. - Lbs. 3 5 8 13 20 30 40 67 107 163
20,000
In. - Lbs. 32 64 96 160 240 360 480 800 — —
Ft. - Lbs. 4 8 12 20 30 45 60 100 160 245
TECHNICAL DATA
30,000
In. - Lbs. 48 98 144 240 360 540 720 — — —
Ft. - Lbs. 5 11 16 27 40 60 80 133 213 327
40,000
In. - Lbs. 64 128 192 320 480 720 — — — —
Ft. - Lbs. 7 13 20 33 50 75 100 167 267 408
50,000
In. - Lbs. 80 160 240 400 600 — — — — —
Ft. - Lbs. 8 16 24 40 60 90 120 200 320 490
60,000
In. - Lbs. 96 192 288 480 720 — — — — —
170

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com TORQUE REQUIRED TO PRODUCE INDICATED BOLT STRESS
Bolt Diameters
1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/4 2 1/2 2 3/4 3
12 17 23 27 37 50 57 73 107 147 197 257
142 200 272 320 800 600 800 — — — — —
24 33 45 53 133 100 133 146 213 293 394 515
285 400 544 640 — — — — — — — —
35 50 68 80 110 150 200 220 320 440 592 772
426 600 — — — — — — — — — —
47 57 91 107 147 200 257 293 427 587 789 1029
568 800 — — — — — — — — — —
59 83 113 133 183 250 333 366 533 733 987 1287
710 — — — — — — — — — — —
71 100 136 160 220 300 400 440 640 880 1184 1544
— — — — — — — — — — — —
83 117 159 187 257 350 467 513 747 1027 1381 1801
— — — — — — — — — — — —
95 133 181 213 293 400 533 587 853 1173 1579 2059
— — — — — — — — — — — —
107 150 204 330 330 450 600 660 690 1320 1776 2316
— — — — — — — — — — — —
118 167 227 267 367 500 667 733 1067 1467 1973 2513
— — — — — — — — — — — —
237 333 453 533 733 1000 1333 1467 2133 2933 3947 5147
— — — — — — — — — — — —
355 500 680 800 1100 1500 2000 2200 3200 4400 5920 7720
TECHNICAL DATA
— — — — — — — — — — — —
473 667 907 1067 1467 2000 2667 2933 4267 5867 7893 10293
— — — — — — — — — — — —
592 833 1133 1333 1833 2500 3333 3667 5333 7333 9867 12867
— — — — — — — — — — — —
710 1000 1360 1600 2200 3000 4000 4400 6400 8800 11840 15430
— — — — — — — — — — — —
171

BOLT TORQUE PROCEDURE
PROCEDURE FOR APPLICATION OF BOLT TORQUE ON FLANGED JOINTS
STEP 1. Align component parts and clamp STEP 5. Apply torque in 20% (1/5) steps of
together with hold down. required final torque, loading all bolts
at each step before proceeding to
STEP 2. Lubricate stud (or bolt) threads next step.
in area of nut or forged ring
engagement, also lubricate face STEP 6. Tighten bolts in sequential order
of nuts (or bolt head) using a 0°-180°, 90°-270°, 45°-225° and 135°-315°
suitable lubricant. at each step until final torque is reached
(see attached sketches).
STEP 3. Install all bolts and nuts finger tight.
STEP 7. Continue to tighten bolts now using
STEP 4. Number bolts so that torquing rotational order until all bolts
requirements can be followed. are stable at final torque level. Two
complete times around is usually
required (see attached sketches).
TECHNICAL DATA
172

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com BOLT TORQUE PROCEDURE
Refer to Bolt Torque Procedure on page 172 before proceeding.
TECHNICAL DATA
173

BOLT TORQUE PROCEDURE
Refer to Bolt Torque Procedure on page 172 before proceeding.
TECHNICAL DATA
174

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com material safety data
1. PRODUCT IDENTIFICATION:
Manufacturer's Name: Weldbend Corporation
Address: 6600 South Harlem Avenue
Argo, Illinois 60501-1930
Telephone Number: (708) 594-1700
Emergency Number: (800) 424-9300 CHEMTREC
Chemical Name & Synonyms: Weld Fittings & Flanges
Chemical Family: Carbon Steel Grade WPB
Formula: Not Applicable
2. PRODUCT DESCRIPTION & HAZARDOUS INGREDIENTS / IDENTITY INFORMATION:

ALLOYING ELEMENTS CAS NO.
Iron (Fe) 7439-89-6
Manganese (Ma)* 7439-96-5
Carbon (C)* 7440-44-0
Aluminum (Al) 7429-90-5
Chromium (Cr) 7440-47-3
Copper (Cu) 7440-50-8
Molybdenum (Mo) 7439-98-7
Nickel (Ni) 7440-02-0
Phosphorus (P)* 7723-14-0
Silicon (Si)* 7440-21-3
Sulfur (S)* 7704-34-9
Boron (B) 7440-42-8
Bismuth (Bi) 7440-69-9
Tellurium (Te) 13494-80-9
Lead (Pb) 7439-92-1
Vanadium (V) 7440-62-2
Titanium (Ti) 7440-32-6
Zinc Coating (Zn) 1314-13-2
Zinc (Zn) 7440-66-6
Cobalt (Co) 7440-48-4
Tungsten (W) 7440-33-7
Tin (Sn) 7440-31-5
*Basic Chemistry carbon steel ASTM requirement
3. Physical Data:
• Melting Point °F (°C): Greater than 2800 (1540)
• Vapor Pressure: Not Applicable
• Vapor Density (Air = 1):
TECHNICAL DATA
Not Applicable
• Solubility in Water: Negligible
• Specific Gravity (H2O = 1): Greater than 7
• % Volatile by Volume (%): Not Applicable
• Evaporation Rate: Not Applicable
175

material safety data
4. Fire And Explosion Hazard Data:
• Flash Point F (C): Not applicable.
• Extinguishing Media: Use methods applicable to surrounding area.
• Flammable Limits: Not applicable.
• Unusual Fire and Explosion Hazards: None.
• S pecial Fire Fighting Procedures: Use self-contained breathing apparatus for protection against degradation
products and fire fighting technique or agent(s) applicable to surrounding materials.
5. Health Hazard Data:

Applicable Statutory or Recommended Occupational Exposure Limits: No Threshold Limit Value (TLV)
or Permissible Exposure Limit (PEL) exists for steel. See chart for listing of individual constituents.
EXPOSURE LIMITS
Material Or Component: OSHA PEL (mg/m3) ACGIH TLV (mg/m3)
Base Metal
Iron (Fe) 10 (Fe2O3 Fume) 5.0 (Fe2O3 Fume)
Alloying Elements
Aluminum (Al) None Listed 5.0 as welding fume
Carbon (C)* None Listed None Listed
Chromium (Cr) 1.0 as chrome 0.5 as chrome
Cobalt (Co) 0.1 as cobalt and fume 0.05 as fume
Columbium (Niobium) 5.0 as dust 10.0 as dust
Copper (Cu) 0.2 as copper; 1.0 as dust 0.2 as fume; 1.0 as dust
Lead (Pb) 0.05 as fume and dust 0.15 as dust and fume
Manganese (Mn)* 5 as manganese 5 as dust; 1 as fume
Molybdenum (Mo) 15 as insoluble compounds 10 as insoluble compounds
Nickel (Ni) 1.0 as Nickel 1.0 as Nickel
Phosphorous (P)* 0.1 as Phosphorus 0.1 as Phosphorus
Silicon (Si)* None Listed 10 total dust
Sulfur (S)* 13 sulfur dioxide 5 sulfur dioxide
Tungsten (W) None Listed 5 insoluble compounds
Vanadium (V) 0.5 dust; 0.1 fume 0.05 dust and fume
Zinc (Zn) coating 5.0 as fume 5.0 as fume
Boron (B) 15.0 as Oxide 10.0 as Oxide
Bismuth (Bi) None Listed None Listed
Tellurium (Te) 0.10 as Compound 0.10 as Compound
Titanium (Ti) 15.0 Dioxide 10.0 Dioxide
Zinc (Zn) 10.0 as Dust 5.0 Oxide; 5 fume
Tin (Sn) None Listed 10.0 as Tin Oxide
*Basic Chemistry carbon steel ASTM requirement

TECHNICAL DATA
Note: T he above listing is a summary of elements used in alloying steel. Various grades of steel will contain
different combinations of these elements. Trace elements may also be present in minute amounts.
*Carbon Steel: The light coating applied to our products does not contain toxic materials such as mercury,
arsenic or lead.
176

TEL: 708/594-1700
FAX: 708/458-0106
www.weldbend.com material safety data
6. Effects Of Overexposure:
Acute: Dust or fume may cause irritation to the eyes, nose, or throat; may leave metallic taste in
mouth; result in metal fume fever; or produce flu-like symptoms.
Chronic:
Aluminum: May initiate fibrotic changes to lung tissue.

Bismuth: No chronic debilitating symptoms indicated from metal.
Boron: No chronic debilitating symptoms indicated.
Chromium: Skin ulceration, irritative dermatitis, allergic reaction, ulceration of the mucous
membranes, perforation of the nasal septum, bronchial carcinoma,
adenocarcinoma, mutagen (?) listed in the National Toxicology Program (NTP).
Annual Report on Carcinogens and found to be a potential carcinogen in the
International Agency for Research on Cancer (IARC) Monographs.
Copper: No chronic debilitating symptoms indicated.
Iron: Siderosis.
Lead: Anemia, urinary dysfunction, metallic taste in mouth, weakness, constipation,
nausea, nervous disorder.
*Manganese: Bronchitis, pneumonitis, lack of coordination.
Molybdenum: Morphological changes in the liver, kidneys, and spleen, anemia, diarrhea,
bone deformity and growth retardation.
Nickel: Inflammation of respiratory tract, pneumoconiosis. Skin sensitizer. Certain
nickel compounds can cause cancer. Listed in NTP Annual Report on
Carcinogens and found to be a potential carcinogen in IARC Monographs.
*Phosphorous: Necrosis of the mandible.
*Sulfur (as sulfur dioxide): Edema of the lungs.
Tellurium: Garlic odor of breath and perspiration, metallic taste in mouth, dryness of the
mouth, inhibition of sweat function, anorexia, nausea.
Titanium: No chronic debilitating symptoms indicated.
Vanadium: Emphysema, pneumonia.
Zinc: Chromosomal anomalies in leukocytes reported. Arthritis, lameness and
inflammation of the gastrointestinal tract reported from animal studies.
Tin: Inorganic tin dust/fumes can cause benign pneumoconiosis of the lungs.
*Carbon Steel
7. Emergency And First Aid Procedures:

In the event of acute exposure, remove to fresh air, administer oxygen, and seek a physician’s assistance.
TECHNICAL DATA
177

material safety data
8. Reactivity Data:
Stability: Considered stable.
Incompatibility: Not incompatible with materials.
Hazardous Polymerization: Not applicable.
Hazardous Decomposition Products: Not applicable.
Conditions to avoid: May liberate metal fumes, metal oxides, or other oxides if exposed to elevated temperatures.
9. Spill Or Leak Procedures:

Steps To Be Take In Case Material is Released or Spilled: Not applicable.
Waste Disposal Method: This material may be reclaimed for reuse.
10. Special Protection Information:

If operations are such that atmospheric levels of contaminants exceed prescribed limits, provide local
exhaust ventilation and/or adequate respiratory protection. Consult your regional codes or code of Federal
Regulations, Title 29, Part 1910.252, Welding, Cutting and Brazing, 1910.134, Respiratory Protection, and 1910
- Subpart Z. Toxic and Hazardous Substances. Personal protective equipment, such as gloves for handling,
goggles and dust filter masks for grinding, proper respirators for welding, etc. should be provided and worn.
Please note that all carbon steel forgings that we manufacture present no health hazard in their natural
state during use, transportation or storage. However, operations such as burning, welding or grinding may
generate concentrations of dust particles or fumes of the alloying elements that may present hazards. For the
information to be effective, it must be passed along to all safety and health personnel in your firm, as well as
to all personnel who handle or use the products and/or are involved with the implementation or control of
operations involving the products.
Disclaimer
Weldbend Corporation believes that the product described in the MSDS would be considered an “article” within the
meaning of Section 1910.1200. This MSDS is intended to be used solely for the purpose of satisfying informational
requests. It is not intended to preempt, replace or expand the terms contained in Weldbend Corporation Conditions
of Sale. Compliance with all the applicable federal, state and local laws and regulations remains the responsibility of
the user, and the user has the responsibility to provide a safe working place, to examine all aspects of its operation,
and to determine if or where precautions, in addition to those described herein, are required.
TECHNICAL DATA
178

“The Industry Standard for
Welding Fittings & Flanges”
Weldbend restricts its sales to Jobbers and/or Distributors only.

Before an order from a new customer is accepted, proof of that
customer’s status as a Jobber and/or Distributor is required.
ALL WELDBEND SALES ARE MADE SOLELY IN ACCORDANCE WITH
WELDBEND’S STANDARD TERMS AND CONDITIONS OF SALES
WHICH ARE SET FORTH HEREIN. Weldbend provides this catalog
for the convenience of its customers in ordering Weldbend
products. Weldbend is not responsible for any printing errors in
the data contained herein, and verification of all specifications
are the sole responsibility of the customers.
We acknowledge the Technical Abilities and Assistance of Mr. Leslie F. Wasdell, C. Eng., M. I. Mech. E.
We acknowledge the Technical Abilities and Assistance of Mr. A.J. DelBuono, P.E.
We acknowledge and appreciate the cooperation of the American Society of Mechanical

Engineers, The American Society of Testing Materials, and the American National Society
Institute for providing a portion of the technical data displayed in this catalog. For further
technical information, the promulgating standard society may be contacted.

TEL: 708/594-1700 TEL: 773/582-3500
FAX: 708/458-0106 FAX: 773/582-7621
www.weldbend.com

Notes
180

TEL: 708/894-1700
FAX: 708/468-0106
www.weldbend.com Notes
181

Notes
182

TEL: 708/894-1700
FAX: 708/468-0106
www.weldbend.com NOTES
183

NOTES
184

TEL: 708/894-1700
FAX: 708/468-0106
www.weldbend.com NOTES
185

TEL: 708/594-1700 TEL: 773/582-3500
FAX: 708/458-0106 FAX: 773/582-7621
www.weldbend.com

WeldBend Catalog

Uploaded by

Copyright:

Available Formats

WeldBend Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WeldBend Catalog

Uploaded by

Copyright:

Available Formats

Carbon Steel Weld Fitting & Weld Flange

Products for Piping Construction

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Weldbend is the industry leader with over

• Over 330,000 sq. ft. of manufacturing

• A prime source producer of fittings • Trained personnel to guarantee prompt

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• From start to finish, Weldbend

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

8" – 10" – 12" Elbow Press

14" – 24" Elbow Press

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Examples of some of the high-quality

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Made only from USA pipe, the

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• From seamless pipe to

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Weldbend's production facility produces

• From cutting, beveling and other finishing

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• After forming our

• Aside from the machine finishing of our

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Each weld flange is machined and finished

• Weldbend only uses steel from the finest

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Weldbend's “On-Hand” inventory policy

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Weldbend packages all

• Weldbend stores inventory in this

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

”The Carton Way is the Better Way “

• Easier stacking • Factory-fresh condition

The Better Way Will Always Be The Weldbend Way!

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• For full size viewing, download from www.weldbend.com.

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Every product manufactured by

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

• Weldbend uses carefully

• All dimensions are

• It is only after all these steps, that the Weldbend name

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

THE WELDBEND POLICY

Weldbend fittings and flanges will meet all applicable

If any Weldbend product fails to meet these ASTM

All Weldbend fittings and flanges are covered by a blanket

Weldbend’s Terms and Conditions of Sales, including

Weldbend’s current Terms and Conditions of Sales are

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

REQUIRED FITTING INFORMATION

1. Quantity (Box quantities may apply)

REQUIRED FLANGE INFORMATION

1. Quantity (Box and Bundle quantities may apply)

1. Matching Pipe Specifications

Copyright © 2010 by Weldbend Corporation. All Rights Reserved.

TERMS AND CONDITIONS

Copyright © 2016 by Weldbend Corporation. All Rights Reserved.