Basic Components of Road Structure and Method of Construction

Basic Components of Road Structure and Method of Construction
Contents [hide]
 1 Basic Components of Road Structure | Flexible Pavements | Road Pavement Layers |

Method of Road Construction
o 1.1 What are the Components of Road structure?
o 1.2 1. Sub Grade:
 1.2.1 Construction:
 1.2.2 Function of Sub grade:
 1.2.3 Material:
 1.2.4 OTHER POSTS:
 1.2.4.1 Method Statement for Asphalt Paving Works | Asphalt
Concrete
 1.2.4.2 Asphalt Concrete Receiving, Placement and Testing
Inspection | Wearing and Binder Course
 1.2.4.3 Characteristics and Size of Aggregates Used in Construction
o 1.3 2. Sub Base:
 1.3.2 Functions of sub base:
 1.3.3 Material:
o 1.4 3. Road Base:
 1.4.2 Functions of Road Base:
 1.4.3 Material:
o 1.5 4. Surface course
 1.5.2 Functions of Surfacing of Road:
 1.5.3 Material:
o 1.6 Others Components of Road Structure:
o 1.7 Carriage Way:
o 1.8 Formation Width:
o 1.9 Kerb:
o 1.10 Medians:
o 1.11 Camber:
o 1.12 Right of Way:
o 1.13 Road Margin:
 1.13.1 Shoulders:
 1.13.2 Bus Bays:
 1.13.3 Parking Lines:
 1.13.4 Sidewalks or Footpath:
 1.13.5 Service Road:
 1.13.6 Cycle Track:
 1.13.7 Guard Rails:
 1.13.8 Drive Way:
 1.13.9 Frontage Roads:
o 1.14 Conclusion:
In this Article today we will talk about the Basic Components of road | Road Structure |
Components of Flexible Pavements | Road Pavement Layers | Road Construction
Layers | Method of Road Construction
Basic Components of road, Road Structure, Components of Flexible Pavements, Road Pavement
Layers
What are the Components of Road structure?
In this article will study about components of the roads and the structure of the roads and its
composition after reading this article you will understand a lot about components of the road
structures. We will try to make it as simple it can be.
1. Sub Grade:
Subgrade is the foundation of the road, thus its the lowest and most important component of
road structure. components of Flexible Pavements
Construction:
 If natural surface is above the formation level then the surface is cut down to proposed sub
grade surface
 If natural surface is below the formation level then the sub grade will be above the ground
level Road Pavement Layers
 It should be constructed at least 60 cm (2ft) high from highest flood level of the area
Function of Sub grade:
 Bears all the load thus acts as a foundation of road

 Transfer load through grain to grain contact
Material:
Material of sub grade should be strong enough to bear the loads, easily accessible and
available in the vicinity and cheap.
2. Sub Base:
Consists of:
1. Upper Base Course

2. Sub or Lower Base Course
Construction:
 Constructed above the sub grade

 Not needed if the sub grade is of very high strength
 In case of flexible pavement upper and lower base courses are separated having different
materials
 In case of rigid pavement only upper base course is provided
 Thickness varies from 7.5 (3in) to 15cm (6in)
Functions of sub base:
 Prevent rise of water or capillary action
Material:
 Should be better than the material of Sub Grade

 The Upper Base Course is made up of sand, gravel, and stone
 The Lower Base Course is made up of cheaply available material i-e rock and stone
fragments Method of Road Construction
3. Road Base:
Due to quality of material used in the road base it is divided into
1. Upper Road Base

2. Lower Road Base
Construction:
 Constructed above the Sub Base
Functions of Road Base:
 To avoid the distortion of wearing course due to its sufficient density

 Supports the wearing course
Material:
 In case of Upper Road Base the material is of high quality as the load intensity is high
 In case of Lower Road Base the material is of high quality as the load intensity decreases
Method of Road Construction
4. Surface course
Surface course is the layer directly in contact with traffic loads and generally contains
superior quality materials. They are usually constructed with dense graded asphalt
concrete(AC). The functions and requirements of this layer are:
 It provides characteristics such as friction, smoothness, drainage, etc. Also it will prevent the
entrance of excessive quantities of surface water into the underlying base, sub-base and
sub-grade,
 It must be tough to resist the distortion under traffic and provide a smooth and skid-
resistant riding surface,
 It must be water proof to protect the entire base and sub-grade from the weakening effect
of water.
Construction:
Constructed usually in two layers
 Binder Course
 Wearing Course (It is the layer which is in direct contact with the tyres of the vehicle)
Functions of Surfacing of Road:
 Prevent penetration of water in to the pavement

 Binder Course binds the Wearing Course with the Road Base
 Wearing Course provide a smooth riding
 Saves the lower layers from abrasion and weathering effects of the moving vehicles
Material:
 Made up of bituminous material

 For Flexible Pavement asphalt concrete is used
 For Rigid Pavements Reinforced Cement Concrete (RCC) is used
Others Components of Road Structure:
There are few component of road structure which are going to be discuss below which are as
follows:
 CARRIAGEWAY
 FORMATION WIDTH
 KERB
 ROAD MARGIN
 MEDIANS
 CAMBER
 RIGHT OF WAY
Carriage Way:
Carriageway is the width of the road on which traffic moves without any restriction.it
generally consist of traffic lines and the width of carriageway depend on the lines of traffic.
Traffic lines are those lines on which traffic can move freely without any restriction. Each
country has its own rules for the width of carriageway for insistence how long should it be in
some country for single line road its 2.44m in some its more than that for two line its 3.75m
in some more then that.
Formation Width:
The formation width of road is the sum of carriageway, shoulders and separators (if there is
any).
Kerb:
Kerb is the boundary line formed from stone or concrete block which separate the
carriageway form footpath. There are different types of kerb with different types of height.
There are four type of kerb which are low or mountable Krebs, semi-barrier kerb, barrier
kerb, and submerged kerb. Iow kerbs are used for traffic to remain in line and also separate
the shoulder from the road so the driver can enter the shoulder area with little difficulty its
height is 10cm (4inch). A semi barrier kerb has height of 15cm (6inches). Barrier kerbs has a
height of 20cm (8 inch). They are provided where pedestrian traffic is in considerable
amount. Submerged kerb are used in rural roads the basically provide stability to the road
pavement.
Medians:
Medians are provided to isolate traffic. Their main area purpose is to restrict the collision of
traffic that are moving in opposite direction of one another.
Camber:
Camber or cross slope is provided in the middle of road or carriageway for the drainage of
rain water form road surface. The main purpose of camber is to prevent water from entering
to the subgrade of the road, the road quickly dries which prevent the traffic from slipping off
the road which decrease the accident rate. The height of camber depends upon the material of
road and the intensity of rain fall in the region. The value of the camber varies from 1 to 25 or
1 to 50.
Right of Way:
Right of way is the total land require for the construction of road. Which include carriages
way, foot path, and future extension. The right of way depends upon the importance of the
road for the future extension.
Road Margin:
The part of road except carriageway are usually called road margin, it includes different parts
or element of road which are given below
 Shoulders
 Bus bays
 Parking lines
 Sidewalks or footpaths
 Service roads
 Cycle track
 Guard rails
 Drive way
 Frontage roads
Shoulders:
Shoulders is a part of formation width except carriage way. Provided alongside the
carriageway it’s basically a road for an emergency use for ambiance in rush hour or to stop a
vehicle for repairing propose, and it can be used for the extension of road in future. The width
of the shoulders is kept in between 2.5 m to 4.6 m.
Bus Bays:
Bus bays or bus stops are stationed on the side of road where the bus can stop safely to pick
up passengers or drop off without disturbing the traffic flow they are provided at least 75m
(250 feet) away from intersection of road.
Parking Lines:
In urban roads they usually provided parking on the road side and parallel parking is
preferred because it does not disturb the traffic flow. Its width is 3m(10feet).
Sidewalks or Footpath:
Sidewalks and footpath is a same word When there is heavy amount of traffic and pedestrian
flow a special paved area is provided for the pedestrian to walk safely on it without any
accident.
Service Road:
Service roads are provided parallel to the main road and also connect to main highway,
expressway. They are separated from the main road and are connected to highway at selected
points. They are provided to not disturb the traffic flow.
Cycle Track:
Cycle track are provided in those areas where the cycle traffic volume is high than width of
the cycle track is kept between 2 to 3 m or in other words (6 to10 feet).
Guard Rails:
Guard rails are usually provided on the shoulder of the road. If the fill is more than 3m (10
feet) they are provided. Their main is purpose to restrict them from falling of the road and to
prevent them from serious accident. Guard rails are made of different types and in different
shapes they are either made of steel, concrete or stone. They are painted white or yellow for
better visibility.
Drive Way:
Drive way join the highway with commercial organizations or buildings such as gas station,
filling station, gasoline station, petrol station etc.
Frontage Roads:
Frontage Roads is constructed to give acquire properties along an essential highway. It may
be run parallel to the highway & segregated by separators.
Conclusion:
Full article on Basic Components of road | Road Structure | Components of Flexible

Pavements | Road Pavement Layers | Road Construction Layers | Method of Road
Construction. Thank you for the full reading of this article in “The Civil Engineering”
platform in English. If you find this post helpful, then help others by sharing it on social
media. If you have any question regarding article please tell me in comments.

Basic Components of Road Structure and Method of Construction

Uploaded by

Copyright:

Available Formats

Basic Components of Road Structure and Method of Construction

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basic Components of Road Structure and Method of Construction

Uploaded by

Copyright:

Available Formats

Basic Components of Road Structure and Method of Construction

 1 Basic Components of Road Structure | Flexible Pavements | Road Pavement Layers |

What are the Components of Road structure?

Function of Sub grade:

 Bears all the load thus acts as a foundation of road

1. Upper Base Course

 Constructed above the sub grade

Functions of sub base:

 Prevent rise of water or capillary action

 Should be better than the material of Sub Grade

Due to quality of material used in the road base it is divided into

1. Upper Road Base

 Constructed above the Sub Base

Functions of Road Base:

 To avoid the distortion of wearing course due to its sufficient density

Constructed usually in two layers

Functions of Surfacing of Road:

 Prevent penetration of water in to the pavement

 Made up of bituminous material

Full article on Basic Components of road | Road Structure | Components of Flexible

You might also like