3GPP TR 36.942

3GPP TR 36.942 V10.3.
0 (2012-06)
Technical Report
3rd Generation Partnership Project;

Technical Specification Group Radio Access Network;
Evolved Universal Terrestrial Radio Access (E-UTRA);
Radio Frequency (RF) system scenarios
(Release 10)
The present document has been developed within the 3rd Generation Partnership Project (3GPP TM) and may be further elaborated for the purposes of 3GPP.
The present document has not been subject to any approval process by the 3GPP Organizational Partners and shall not be implemented.
This Specification is provided for future development work within 3GPP only. The Organizational Partners accept no liability for any use of this Specification.
Specifications and reports for implementation of the 3GPP TM system should be obtained via the 3GPP Organizational Partners' Publications Offices.
Release 100T 2 3GPP TR 36.942 V10.3.0 (2012-06)
Keywords
LTE, Radio
3GPP
Postal address
3GPP support office address

650 Route des Lucioles - Sophia Antipolis
Valbonne - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Internet
http://www.3gpp.org
Copyright Notification
No part may be reproduced except as authorized by written permission.

The copyright and the foregoing restriction extend to reproduction in all media.
© 2012, 3GPP Organizational Partners (ARIB, ATIS, CCSA, ETSI, TTA, TTC).
All rights reserved.
UMTS™ is a Trade Mark of ETSI registered for the benefit of its members
3GPP™ is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners
LTE™ is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners
GSM® and the GSM logo are registered and owned by the GSM Association
3GPP
Release 100T 3 3GPP TR 36.942 V10.3.0 (2012-06)
Contents
Foreword ......................................................................................................................................................6
1 Scope ..................................................................................................................................................7
2 References ..........................................................................................................................................7
3 Definitions, symbols and abbreviations ...............................................................................................8
3.1 Definitions ...................................................................................................................................................8
3.2 Symbols .......................................................................................................................................................8
3.3 Abbreviations...............................................................................................................................................8
4 General assumptions ...........................................................................................................................9
4.1 Interference scenarios................................................................................................................................. 10
4.2 Antenna Models ......................................................................................................................................... 10
4.2.1 BS antennas .......................................................................................................................................... 10
4.2.1.1 BS antenna radiation pattern ............................................................................................................ 10
4.2.1.2 BS antenna heights and antenna gains for macro cells ...................................................................... 11
4.2.2 UE antenna ........................................................................................................................................... 11
4.2.3 MIMO antenna Characteristics .............................................................................................................. 11
4.3 Cell definitions........................................................................................................................................... 11
4.4 Cell layouts ................................................................................................................................................ 12
4.4.1 Single operator cell layouts ................................................................................................................... 12
4.4.1.1 Macro cellular deployment .............................................................................................................. 12
4.4.2 Multi operator / Multi layer cell layouts ................................................................................................ 12
4.4.2.1 Uncoordinated macro cellular deployment ....................................................................................... 12
4.4.2.2 Coordinated macro cellular deployment ........................................................................................... 13
4.5 Propagation conditions and channel models ................................................................................................ 14
4.5.1 Received signal..................................................................................................................................... 14
4.5.2 Macro cell propagation model – Urban Area ......................................................................................... 14
4.5.3 Macro cell propagation model – Rural Area .......................................................................................... 15
4.6 Base-station model ..................................................................................................................................... 15
4.7 UE model................................................................................................................................................... 17
4.8 RRM models .............................................................................................................................................. 18
4.8.1 Measurement models ............................................................................................................................ 18
4.8.2 Modelling of the functions .................................................................................................................... 18
4.9 Link level simulation assumptions .............................................................................................................. 18
4.10 System simulation assumptions .................................................................................................................. 18
4.10.1 System loading ..................................................................................................................................... 18
5 Methodology description................................................................................................................... 18
5.1 Methodology for co-existence simulations .................................................................................................. 18
5.1.1 Simulation assumptions for co-existence simulations............................................................................. 18
5.1.1.1 Scheduler ........................................................................................................................................ 18
5.1.1.2 Simulated services ........................................................................................................................... 19
5.1.1.3 ACIR value and granularity ............................................................................................................. 19
5.1.1.4.1 Uplink Asymmetrical Bandwidths ACIR (Aggressor with larger bandwidth)............................... 19
5.1.1.4.2 Uplink Asymmetrical Bandwidths ACIR (Aggressor with smaller bandwidth) ............................ 22
5.1.1.4 Frequency re-use and interference mitigation schemes for E-UTRA ................................................. 22
5.1.1.5 CQI estimation ................................................................................................................................ 23
5.1.1.6 Power control modelling for E-UTRA and 3.84 Mcps TDD UTRA .................................................. 23
5.1.1.7 SIR target requirements for simulated services ................................................................................. 23
5.1.1.8 Number of required snapshots.......................................................................................................... 23
5.1.1.9 Simulation output ............................................................................................................................ 23
5.1.2 Simulation description .......................................................................................................................... 24
5.1.2.1 Downlink E-UTRA interferer UTRA victim .................................................................................... 24
5.1.2.2 Downlink E-UTRA interferer E-UTRA victim ................................................................................. 24
5.1.2.3 Uplink E-UTRA interferer UTRA victim ......................................................................................... 25
5.1.2.4 Uplink E-UTRA interferer E-UTRA victim ..................................................................................... 25
3GPP
Release 100T 4 3GPP TR 36.942 V10.3.0 (2012-06)
6 System scenarios ............................................................................................................................... 26

6.1 Co-existence scenarios ............................................................................................................................... 26
7 Results .............................................................................................................................................. 26
7.1 Radio reception and transmission ............................................................................................................... 26
7.1.1 FDD coexistence simulation results....................................................................................................... 26
7.1.1.1 ACIR downlink 5MHz E-UTRA interferer – UTRA victim .............................................................. 26
7.1.1.2 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA victim ............................................ 27
7.1.1.3 ACIR uplink 5MHz E-UTRA interferer – UTRA victim .................................................................. 29
7.1.1.4 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA victim ................................................ 31
7.1.2 TDD coexistence simulation results ...................................................................................................... 34
7.1.2.1 ACIR downlink 5MHz E-UTRA interferer – UTRA 3.84 Mcps TDD victim .................................... 34
7.1.2.2 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim ................................... 36
7.1.2.3 ACIR downlink 1.6 MHz E-UTRA interferer – UTRA 1.28 Mcps TDD victim ................................ 38
7.1.2.4 ACIR uplink 5MHz E-UTRA interferer – UTRA 3.84 Mcps TDD victim......................................... 41
7.1.2.5 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim........................................ 43
7.1.2.6 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim (LCR frame structure
based) ............................................................................................................................................. 45
7.1.2.7 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim (LCR frame
structure based) ............................................................................................................................... 46
7.1.3 Additional coexistence simulation results .............................................................................................. 48
7.1.3.1 ACIR downlink E-UTRA interferer – GSM victim .......................................................................... 48
7.1.3.2 ACIR uplink E-UTRA interferer – GSM victim ............................................................................... 50
7.1.3.3 Asymmetric coexistence 20 MHz and 5 MHz E-UTRA .................................................................... 51
7.1.3.4 Impact of cell range and simulation frequency on ACIR................................................................... 53
7.1.3.5 Uplink Asymmetric coexistence TDD E-UTRA to TDD E-UTRA ................................................... 54
7.1.4 Base station blocking simulation results ................................................................................................ 56
7.2 RRM.......................................................................................................................................................... 58
8 Rationales for co-existence requirements........................................................................................... 58
8.1 BS and UE ACLR ...................................................................................................................................... 58
8.1.1 Requirements for E-UTRA – UTRA co-existence ................................................................................. 58
8.1.2 Requirements for E-UTRA – E-UTRA co-existence .............................................................................. 59
9 Deployment aspects .......................................................................................................................... 59
9.1 UE power distribution ................................................................................................................................ 59
9.1.1 Simulation results ................................................................................................................................. 60
10 Multi-carrier BS requirements ........................................................................................................... 62
10.1 Unwanted emission requirements for multi-carrier BS ................................................................................ 62
10.1.1 General................................................................................................................................................. 62
10.1.2 Multi-carrier BS of different E-UTRA channel bandwidths ................................................................... 63
10.1.3 Multi-carrier BS of E-UTRA and UTRA ............................................................................................... 63
10.2 Receiver requirements for multi-carrier BS ................................................................................................. 64
10.2.1 General................................................................................................................................................. 64
10.2.2 Test principles for a multi-carrier BS of equal or different E-UTRA channel bandwidths ....................... 65
11 Rationale for unwanted emission specifications ................................................................................. 65
11.1 Out of band Emissions ............................................................................................................................... 65
11.1.1 Operating band unwanted emission requirements for E-UTRA BS (spectrum emission mask) ................ 65
11.1.2 ACLR requirements for E-UTRA BS .................................................................................................... 67
11.2 Spurious emissions..................................................................................................................................... 69
11.2.1 BS Spurious emissions.......................................................................................................................... 69
11.2.2 General spurious emissions requirements for E-UTRA BS .................................................................... 69
11.2.3 Specification of BS Spurious emissions outside the operating band........................................................ 70
11.2.4 Additional spurious emissions requirements .......................................................................................... 70
12 LTE-Advanced co-existence ............................................................................................................. 71
12.1 Methodology and simulation assumptions for co-existence simulations ....................................................... 71
12.1.1 Simulation scenarios ............................................................................................................................. 71
12.1.2 Number of UEs per sub-frame.............................................................................................................. 71
12.1.3 ACIR model ........................................................................................................................................ 72
12.1.3.1 Uplink ACIR model ........................................................................................................................ 72
12.1.3.2 Downlink ACIR model .................................................................................................................... 75
3GPP
Release 100T 5 3GPP TR 36.942 V10.3.0 (2012-06)
12.1.4 Uplink power control ........................................................................................................................... 76

12.2 Results ....................................................................................................................................................... 77
12.2.1 Radio reception and transmission .......................................................................................................... 77
12.2.1.1 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 10 MHz E-UTRA victim ......................... 77
12.2.1.2 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 10 MHz E-UTRA victim ............................. 79
12.2.1.3 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 40 MHz Advanced E-UTRA victim ........ 83
12.2.1.4 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 40 MHz Advanced E-UTRA victim ............. 85
12.2.1.5 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 5 MHz UTRA victim .............................. 89
12.2.1.6 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 5 MHz UTRA victim ................................... 90
12.2.1.5 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 1.6 MHz UTRA victim ........................... 92
12.2.1.6 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 1.6 MHz UTRA victim ................................ 93
Annex A (informative): Link Level Performance Model ................................................................. 96

A.1 Description ................................................................................................................................................ 96
A.2 Modelling of Link Adaptation .................................................................................................................... 98
A.3 UTRA 3.84 Mcps TDD HSDPA Link Level Performance........................................................................... 99
A.4 Link Level Performance for E-UTRA TDD (LCR TDD frame structure based) ......................................... 101
Annex B (informative): Smart Antenna Model for UTRA 1.28 Mcps TDD.................................. 103
B.1 Description .............................................................................................................................................. 103
Annex C (informative): Simulation assumptions for LTE-A coexistence...................................... 107

Annex D (informative): Change history ......................................................................................... 109
3GPP
Release 100T 6 3GPP TR 36.942 V10.3.0 (2012-06)
Foreword
This Technical Report has been produced by the 3rd Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates,
etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
3GPP
Release 100T 7 3GPP TR 36.942 V10.3.0 (2012-06)
1 Scope
During the E-UTRA standards development, the physical layer parameters will be decided using system scenarios,
together with implementation issues, reflecting the environments that E-UTRA will be designed to operate in.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TR 25.896, “Feasibility Study for Enhanced Uplink for UTRA FDD”
[2] 3GPP TR 25.816, “UMTS 900 MHz Work Item Technical Report”
[3] 3GPP TR 25.942, “Radio Frequency (RF) system scenarios”
[4] 3GPP TR 25.814, “Physical Layer Aspects for Evolved UTRA”
[5] 3GPP TR 30.03, “Selection procedures for the choice of radio transmission technologies of the
UMTS”
[6] R4-051146, “Some operators’ requirements for prioritization of performance requirements work in
RAN WG4”, RAN4#37
[7] 3GPP TR 25.951, “FDD Base Station (BS) classification”
[8] 3GPP TR 25.895, ”Analysis of higher chip rates for UTRA TDD evolution.”
[9] R4-070235, “Analysis of co-existence simulation results”, RAN4#42
[10] R4-070084, “Coexistence Simulation Results for 5MHz E-UTRA -> UTRA FDD Uplink with
Revised Simulation Assumptions”, RAN4#42
[11] R4-070034, “Additional simulation results on 5 MHz LTE to WCDMA FDD UL co-existence
studies”, RAN4#42
[12] R4-070262, “Simulation results on 5 MHz LTE to WCDMA FDD UL co-existence studies with
revised simulation assumptions”, RAN4#42
[13] R4-070263, “Proposal on LTE ACLR requirements for UE”, RAN4#42
[14] R4-061288, “Downlink LTE 900 (Rural Macro) with Downlink GSM900 (Rural Macro) Co-
existence Simulation Results”, RAN4#41
[15] R4-070391, “LTE 900 - GSM 900 Downlink Coexistence”, RAN4#42bis
[16] R4-061304, “LTE 900 - GSM 900 Uplink Simulation Results”, RAN4#41
[17] R4-070390, “LTE 900 - GSM 900 Uplink Simulation Results”, RAN4#42bis
[18] R4-070392 “LTE-LTE Coexistence with asymmetrical bandwidth”, RAN4#42bis
[19] 3GPP TS 36.104, ”Base Station (BS) radio transmission and reception”
3GPP
Release 100T 8 3GPP TR 36.942 V10.3.0 (2012-06)
[20] 3GPP TS 25.104, ”Base Station (BS) radio transmission and reception (FDD)”
[21] 3GPP TS 36.141, ”Base Station (BS) conformance testing”
[22] Recommendation ITU-R SM.329-10, “Unwanted emissions in the spurious domain”
[23] “International Telecommunications Union Radio Regulations”, Edition 2004, Volume 1 – Articles,
ITU, December 2004.
[24] “Adjacent Band Compatibility between UMTS and Other Services in the 2 GHz Band”, ERC
Report 65, Menton, May 1999, revised in Helsinki, November 1999.
[25] “Title 47 of the Code of Federal Regulations (CFR)”, Federal Communications Commission.
[26] R4-070337, "Impact of second adjacent channel ACLR/ACS on ACIR" (Nokia Siemens
Networks).
[27] R4-070430, "UE ACS and BS ACLRs" (Fujitsu ).
[28] R4-070264, "Proposal on LTE ACLR requirements for Node B" (NTT DoCoMo).
[29] Recommendation ITU-R M.1580-1, “Generic unwanted emission characteristics of base stations
using the terrestrial radio interfaces of IMT-2000”.
[30] Report ITU-R M.2039, “Characteristics of terrestrial IMT-2000 systems for frequency
sharing/interference analyses”.
[31] ETSI EN 301 908-3 V2.2.1 (2003-10), “Electromagnetic compatibility and Radio spectrum
Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-
Generation cellular networks; Part 3: Harmonized EN for IMT-2000, CDMA Direct Spread
(UTRA FDD) (BS) covering essential requirements of article 3.2 of the R&TTE Directive”.
3 Definitions, symbols and abbreviations
3.1 Definitions
3.2 Symbols
3.3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ACIR Adjacent Channel Interference Ratio

ACLR Adjacent Channel Leakage power Ratio
ACS Adjacent Channel Selectivity
AMC Adaptive Modulation and Coding
AWGN Additive White Gaussian Noise
BS Base Station
CDF Cumulative Distribution Function
DL Downlink
FDD Frequency Division Duplex
3GPP
Release 100T 9 3GPP TR 36.942 V10.3.0 (2012-06)
MC Monte-Carlo
MCL Minimum Coupling Loss
MCS Modulation and Coding Scheme
PC Power Control
PSD Power Spectral Density
RX Receiver
TDD Time Division Duplex
TX Transmitter
UE User Equipment
UL Uplink
4 General assumptions
The present document discusses system scenarios for E-UTRA operation primarily with respect to the radio
transmission and reception including the RRM aspects. To develop the E-UTRA standard, all the relevant scenarios
need to be considered for the various aspects of operation and the most critical cases identified. The process may then
be iterated to arrive at final parameters that meet both service and implementation requirements.
The E-UTRA system is intended to be operated in the same frequency bands specified for UTRA. In order to limit the
number of frequency bands to be simulated in the various simulation scenarios a mapping of frequency bands to two
simulation frequencies (900 MHz and 2000 MHz) is applied. When using the macro cell propagation model of
TR25.942 [3], the frequency contributes to the path loss by 21*log10(f). The maximum path loss difference between the
lowest/highest frequencies per E-UTRA frequency band and corresponding simulation frequency is shown in tables 4.1
and 4.2.
Table 4.1: Simulation frequencies for FDD mode E-UTRA frequency bands
UL frequencies DL frequencies
Simulation Path loss difference (dB)
E-UTRA (MHz) (MHz)
frequency
Band lowest UL highest DL
lowest highest lowest highest (MHz)
frequency frequency
1 1920 1980 2110 2170 2000 0.37 0.74
2 1850 1910 1930 1990 2000 0.71 0.05
3 1710 1785 1805 1880 2000 1.43 0.56
4 1710 1755 2110 2155 2000 1.43 0.68
5 824 849 869 894 900 0.80 0.06
6 830 840 875 885 900 0.74 0.15
7 2500 2570 2620 2690 2000 2.04 2.70
8 880 915 925 960 900 0.20 0.59
9 1749.9 1784.9 1844.9 1879.9 2000 1.22 0.56
10 1710 1770 2110 2170 2000 1.43 0.74
11 1427.9 1452.9 1475.9 1500.9 2000 3.07 2.62
Table 4.2: Simulation frequencies for TDD mode E-UTRA frequency bands
UL/DL
Simulation
E-UTRA frequencies Path loss difference (dB)
(MHz) frequency
band
(MHz)
lowest highest lowest frequency highest frequency
33 1900 1920 2000 0.47 0.37
34 2010 2025 2000 0.05 0.11
35 1850 1910 2000 0.71 0.42
36 1930 1990 2000 0.32 0.05
37 1910 1930 2000 0.42 0.32
38 2570 2620 2000 2.29 2.46
It can be observed that the difference of path loss between simulation frequency and operating frequency (except bands
7, 11 and 38) is in the worst case less than 0.8 dB for the downlink and less the 1,5 dB for the uplink. Hence the
mapping of operating frequency to simulation frequency will provide valid results.
3GPP
Release 100T 10 3GPP TR 36.942 V10.3.0 (2012-06)
The validity of simulations performed at 2 GHz for the 2.6 GHz bands 7 and 38 was already analyzed in TR 25.810.
Considering the expected higher antenna gain in the 2.6 GHz band the difference in path loss is in the order of 1 dB
what is comparable to the other frequency bands.
4.1 Interference scenarios

This chapter should cover how the interference scenarios could occur e.g. BS-BS, UE-BS etc.
4.2 Antenna Models

This chapter contains the various antenna models for BS and UE
4.2.1 BS antennas
4.2.1.1 BS antenna radiation pattern

The BS antenna radiation pattern to be used for each sector in 3-sector cell sites is plotted in Figure 4.1. The pattern is
identical to those defined in [1], [2] and [4]:
  θ 2 
A (θ ) =− min 12   , Am  where − 180 ≤ θ ≤ 180 ,
  θ 3dB  
θ 3dB is the 3dB beam width which corresponds to 65 degrees, and Am = 20dB is the maximum attenuation
3GPP
Release 100T 11 3GPP TR 36.942 V10.3.0 (2012-06)
-5
-10
Gain - dB
-15
-20
-25
-180 -150 -120 -90 -60 -30 0 30 60 90 120 150 180
Horizontal Angle - Degrees
Figure 4.1: Antenna Pattern for 3-Sector Cells
4.2.1.2 BS antenna heights and antenna gains for macro cells

Antenna heights and gains for macro cells are given in table 4.3.
Table 4.3: Antenna height and gain for Macro Cells
Rural Area Urban Area

900 MHz 2000 MHz 900 MHz
BS antenna gain (dBi)
15 15 12
(including feeder loss)
BS antenna height (m) 45 30 30
4.2.2 UE antenna
For UE antennas, a omni-directional radiation pattern with antenna gain 0dBi is assumed [2], [3], [4].
4.2.3 MIMO antenna Characteristics

xxxx
4.3 Cell definitions

This chapter contain the cell properties e.g. cell range, cell type (omni, sector), MIMO cell definitions etc.
3GPP
Release 100T 12 3GPP TR 36.942 V10.3.0 (2012-06)
4.4 Cell layouts

This chapter contains different cell layouts in form of e.g. single operator, multi-operator and multi layer cell layouts
(e.g. macro-micro etc).
4.4.1 Single operator cell layouts
4.4.1.1 Macro cellular deployment

Base stations with 3 sectors per site are placed on a hexagonal grid with distance of 3*R, where R is the cell radius (see
Figure 4.2), with wrap around. The number of sites shall be equal to or higher than 19. [2] [4].
Figure 4.2: Single operator cell layout
4.4.2 Multi operator / Multi layer cell layouts
4.4.2.1 Uncoordinated macro cellular deployment

For uncoordinated network simulations, identical cell layouts for each network shall be applied, with worst case shift
between sites. Second network’s sites are located at the first network’s cell edge, as shown in Figure 4.3 [2].
3GPP
Release 100T 13 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 4.3: Multi operator cell layout - uncoordinated operation
4.4.2.2 Coordinated macro cellular deployment

For coordinated network simulations, co-location of sites is assumed; hence identical cell layouts for each network shall
be applied [2].
Figure 4.4: Multi operator cell layout - coordinated operation
3GPP
Release 100T 14 3GPP TR 36.942 V10.3.0 (2012-06)
4.5 Propagation conditions and channel models

This chapter contains the definition of channel models, propagation conditions for various environments e.g. urban,
suburban etc.
For each environment a propagation model is used to evaluate the propagation pathloss due to the distance. Propagation
models are adopted from [3] and [4] and presented in the following clauses.
4.5.1 Received signal

An important parameter to be defined is the minimum coupling loss (MCL). MCL is the parameter describing the
minimum loss in signal between BS and UE or UE and UE in the worst case and is defined as the minimum distance
loss including antenna gains measured between antenna connectors. MCL values are adopted from [3] and [7] as
follows:
Table 4.4: Minimum Coupling Losses
Environment Scenario MCL

Macro cell Urban Area BS ↔ UE 70 dB
Macro cell Rural Area BS ↔ UE 80 dB
With the above definition, the received power in downlink and uplink can be expressed as [3]:
RX_PWR = TX_PWR – Max (pathloss – G_TX – G_RX, MCL)
where:
RX_PWR is the received signal power
TX_PWR is the transmitted signal power
G_TX is the transmitter antenna gain
G_RX is the receiver antenna gain
4.5.2 Macro cell propagation model – Urban Area

Macro cell propagation model for urban area is applicable for scenarios in urban and suburban areas outside the high
rise core where the buildings are of nearly uniform height [3]:
L = 40 ⋅ (1 − 4 ⋅10 −3 ⋅ Dhb) ⋅ log10 (R) − 18 ⋅ log10 (Dhb) + 21 ⋅ log10 (f) + 80dB
where:
R is the base station-UE separation in kilometres
f is the carrier frequency in MHz
Dhb is the base station antenna height in metres, measured from the average rooftop level
Considering a carrier frequency of 900MHz and a base station antenna height of 15 metres above average rooftop level,
the propagation model is given by the following formula [4]:
L = 120,9 + 37,6log10 (R)

where:
Considering a carrier frequency of 2000MHz and a base station antenna height of 15 metres above average rooftop level,
the propagation model is given by the following formula:
3GPP
Release 100T 15 3GPP TR 36.942 V10.3.0 (2012-06)
L = 128,1 + 37,6log10 (R)
where:
After L is calculated, log-normally distributed shadowing (LogF) with standard deviation of 10dB should be added [2],
[3]. A Shadowing correlation factor of 0.5 for the shadowing between sites (regardless aggressing or victim system) and
of 1 between sectors of the same site shall be used The pathloss is given by the following formula:
Pathloss_macro = L + LogF
NOTE 1: L shall in no circumstances be less than free space loss. This model is valid for NLOS case only and
describes worse case propagation
NOTE 2: The pathloss model is valid for a range of Dhb from 0 to 50 metres.
NOTE 3: This model is designed mainly for distance from few hundred meters to kilometres. This model is not
very accurate for short distances.
NOTE 4: The mean building height is equal to the sum of mobile antenna height (1,5m) and Δh m = 10,5m [5].
NOTE 5: Some downlink simulations in this TR were performed without shadowing correlation, however it was
reported this has a negligible impact on the simulation results.
4.5.3 Macro cell propagation model – Rural Area

For rural area, the Hata model was used in the work item UMTS900[2], this model can be reused:
L (R)= 69.55 +26.16log 10 (f)–13.82log 10 (Hb)+[44.9-6.55log 10 (Hb)]log(R) – 4.78(Log 10 (f))2+18.33 log 10 (f) -40.94
where:
f is the carrier frequency in MHz
Hb is the base station antenna height above ground in metres
Considering a carrier frequency of 900MHz and a base station antenna height of 45 meters above ground the
propagation model is given by the following formula:
L = 95,5 + 34,1log10 (R)
where:
After L is calculated, log-normally distributed shadowing (LogF) with standard deviation of 10dB should be added [2],
[3]. A Shadowing correlation factor of 0.5 for the shadowing between sites (regardless aggressing or victim system) and
of 1 between sectors of the same site shall be used. The pathloss is given by the following formula:
Pathloss_macro = L + LogF
NOTE 1: L shall in no circumstances be less than free space loss. This model is valid for NLOS case only and
describes worse case propagation
NOTE 2: This model is designed mainly for distance from few hundred meters to kilometres. This model is not
very accurate for short distances.
4.6 Base-station model

This chapter covers the fundamental BS properties e.g. output power, dynamic range, noise floor etc.
3GPP
Release 100T 16 3GPP TR 36.942 V10.3.0 (2012-06)
Reference UTRA FDD base station parameters are given in Table 4.5.
Table 4.5: UTRA FDD reference base station parameters
Parameter Value Note

Maximum BS power 43dBm [2], [3]
Maximum power per DL traffic channel 30dBm [2], [3]
Minimum BS power per user 15dBm [2]
Total CCH power 33dBm [2]
Noise Figure 5dB [3]
Reference base station parameters for UTRA 1.28Mcps TDD are given in Table 4.5a.
Table 4.5a: Reference base station for UTRA 1.28Mcps TDD

Maximum BS power 34dBm
Maximum power per DL traffic channel 22dBm 34-10*log10(16)=22dBm
power control dynamic 30dB
Noise Figure 7dB
Noise power -106dBm
Reference sensitivity -110dBm
Target CIR for 12.2kbps voice -2.5 dB
Reference UTRA 3.84 Mcps TDD base station parameters are given in Table 4.5b.
Table 4.5b: Reference base station for UTRA 3.84Mcps TDD

Maximum BS Power 43 dBm
Max power per DL traffic channel Up to the maximum base station transmit
power may be assigned to each timeslot
and users may be multiplexed between
timeslots
Noise Figure 5 dB
Reference E-UTRA FDD and E-UTRA TDD base station parameters are given in Table 4.6.
Table 4.6: E-UTRA FDD and E-UTRA TDD reference base station parameters

Maximum BS power 43dBm for 1.25, 2.5 and 5MHz carrier [4]
46dBm for 10, 15 and 20MHz carrier
Maximum power per DL traffic channel 32dBm
Noise Figure 5dB [4]
Reference base station parameters for E-UTRA TDD (LCR TDD frame structure based) are given in Table 4.6a.
Table 4.6a: Reference base station for E-UTRA TDD (LCR TDD frame structure based)

Maximum BS power 43dBm for bandwidth ≤ 5MHz
46dBm for 10, 15 and 20MHz bandwidth
Maximum power per RB Maximum BS power/ Nr. of available 375kHz RB size*
RB’s
Noise Figure 6dB
Noise power Varies with system BW Noise power should be
calculated based on different
BW option.
NOTE: * When there is new decision in RAN1, new RB size for 1.6MHz should be reconsidered.
3GPP
Release 100T 17 3GPP TR 36.942 V10.3.0 (2012-06)
4.7 UE model
This chapter covers the fundamental UE properties e.g. output power, dynamic range, noise floor etc.
Reference UTRA FDD parameters are given in Table 4.7.
Table 4.7: UTRA FDD reference UE parameters

Maximum UE power 21dBm [2], [3]
Minimum UE power -50dBm [2]
Noise Figure* 9dB [3]
NOTE: * UTRA TDD UE will have a relatively lower Noise Figure since it does not have a duplexer. However,
for simulation alignment purpose, a Noise Figure of 9 dB will be used.
Reference UTRA 1.28 Mcps TDD parameters are given in Table 4.7a
Table 4.7a: Reference UE for UTRA 1.28 Mcps TDD

Maximum UE power 21dBm
Minimum UE power -49dBm
Noise Figure 9dB
Antenna model 0dBi
Noise power -104dBm
Reference sensitivity -108dBm
Target CIR -2.5 dB
Reference UTRA 3.84 Mcps TDD UE parameters are given in Table 4.7b.
Table 4.7b: UTRA 3.84 Mcps TDD reference UE parameters

Maximum UE power 24dBm [2], [3]
NOTE: * UTRA TDD UE will have a relatively lower Noise Figure since it does not have a duplexer. However,
for simulation alignment purpose, a Noise Figure of 9 dB will be used.
Reference E-UTRA FDD and E-UTRA TDD UE parameters are given in Table 4.8.
Table 4.8: E-UTRA FDD and E-UTRA TDD reference UE parameters

Maximum UE power 24dBm [6]
NOTE: * E-UTRA TDD UE will have a relatively lower Noise Figure since it does not have a duplexer.
However, for simulation alignment purpose, a Noise Figure of 9 dB will be used.
Reference E-UTRA TDD UE (LCR TDD frame structure based) parameters are given in Table 4.8a.
3GPP
Release 100T 18 3GPP TR 36.942 V10.3.0 (2012-06)
Table 4.8a: Reference UE for EUTRA TDD (LCR TDD frame structure based)

Maximum UE power 24dBm
Minimum UE power -30dBm
Noise Figure 9dB
Noise power Varies with the total RB’s allocated for a UE
4.8 RRM models

This chapter contains models that are necessary to study the RRM aspects e.g.
4.8.1 Measurement models

xxxx
4.8.2 Modelling of the functions

xxxx
4.9 Link level simulation assumptions

This chapter covers Layer 1 aspects and assumptions (e.g. number of HARQ retransmissions) etc.
4.10 System simulation assumptions

This chapter contains system simulation assumptions e.g. Eb/No values for different services, activity factor for voice,
power control steps, performance measures (system throughput, grade of service), confidence interval etc.
4.10.1 System loading

xxxx
5 Methodology description
This chapter describes the methods used for various study items e.g. deterministic analysis for BS-BS interference,
Monte-Carlo simulations and dynamic type of simulations for RRM.
5.1 Methodology for co-existence simulations

Simulations to investigate the mutual interference impact of E-UTRA, UTRA and GERAN are based on snapshots were
users are randomly placed in a predefined deployment scenario (Monte-Carlo approach). Assumptions or E-UTRA in
this chapter are based on the physical layer (OFDMA DL and SC-FDMA UL) as described in the E-UTRA study item
report [4]. It must be noted that actual E-UTRA physical layer specification of frequency resource block is different
regarding number of sub-carriers per resource block (12 instead of 25 specified in [4]) and regarding the size of a
resource block (180 kHz instead of 375 kHz in [4]). However, this has no impact on the results and conclusions of the
present document.
5.1.1 Simulation assumptions for co-existence simulations
5.1.1.1 Scheduler
For initial E-UTRA coexistence simulations Round Robin scheduler shall be used.
3GPP
Release 100T 19 3GPP TR 36.942 V10.3.0 (2012-06)
5.1.1.2 Simulated services

When using Round Robin scheduler, full buffer traffic shall be simulated. For E-UTRA downlink, one frequency
resource block for one user shall be used. The E-UTRA system shall be maximum loaded, i.e. 24 frequency resource
blocks in 10 MHz bandwidth and 12 frequency resource blocks in 5 MHz bandwidth respectively. For E-UTRA uplink,
the number of allocated frequency resource blocks for one user is 4 for 5 MHz bandwidth and 8 for 10 MHz bandwidth
respectively.
For the 5 MHz TDD UTRA victim using 3.84 Mcps TDD, Enhanced Uplink providing data service shall be used where
1 UE shall occupy 1 Resource Unit (code x timeslot). Here the number of UE per timeslot is set to 3 UEs/timeslot.
Other services, e.g. constant bit rate services are FFS.
5.1.1.3 ACIR value and granularity

For downlink a common ACIR for all frequency resource blocks to calculate inter-system shall be used. Frequency
resource block specific ACIR is FFS.
For uplink it is assumed that the ACIR is dominated by the UE ACLR. The ACLR model is described in table 5.1 and
table 5.2
Table 5.1: ACLR model for 5MHz E-UTRA interferer and UTRA victim, 4 RBs per UE
Location of aggressor Adjacent to victim channel at least 4 RBs away from channel
4RBs (bandwidth = 4*375 edge edge
kHz)
ACLR dBc/3.84MHz 30 + X 43+X
X serves as the step size for simulations, X = … -10, -5, 0, 5, 10… dB
Table 5.2: ACLR model for E-UTRA interferer and 10MHz E-UTRA victim
E-UTRA Number of Bandwidth ACLR dB/ B Aggressor

RBs per UE (B Aggressor ) Adjacent to edge of Non Adjacent to edge
victim RBs of victim RBs
5 MHz 4 4 RB (4 × 375 kHz) 30 + X (less than 4 43 + X (more than 4
RBs away) RBs away)
RBs away) RBs away)
RBs away) RBs away)
RBs away) RBs away)
X serves as the step size for simulations, X = … -10, -5, 0, 5, 10… dB
Note: This ACLR models are agreed for the purpose of co-existence simulations. ACLR/ACS requirements
need to be discussed separately.
5.1.1.4.1 Uplink Asymmetrical Bandwidths ACIR (Aggressor with larger bandwidth)

Since the uplink ACLR of the aggressor is measured in the aggressor’s bandwidth, for uplink asymmetrical bandwidth
coexistence, a victim UE with a smaller bandwidth than that of the aggressor will receive a fraction of the interference
power caused by the aggressor’s ACLR. For two victim UEs falling within the 1st ACLR of the aggressor, the victim
UE closer in frequency to the aggressor will experience higher interference than one that is further away in frequency.
The difference in interference depends on the power spectral density (PSD) within the aggressor’s 1st ACLR bandwidth.
For simplicity, it is assumed that the PSD is flat across the aggressor’s ACLR bandwidth. Hence, the ACLR can be
adjusted by the factor, F ACLR :
F ACLR = 10 × LOG 10 (B victim/B Aggressor )
Where, BAggressor and BVictim are the E-UTRA aggressor and victim bandwidths respectively.
3GPP
Release 100T 20 3GPP TR 36.942 V10.3.0 (2012-06)
30 + X 43 + X
UE1 UE2 UE3 Interfering UE
Victim UE
16 RB 16 RB 16 RB
ACLR
20 MHz E-UTRA 5 MHz E-UTRA
Figure 5.1: 20 MHz E-UTRA UE aggressor to 5 MHz E-UTRA UE victims
30 + X 43 + X
Interfering UE
UE1 UE2 UE3
Victim UE
16 RB 16 RB 16 RB
ACLR
In Table 5.2, the aggressor UE that is non adjacent to the victim UE, the victim UE will experience an interference due
to an ACLR of 43 + X – F ACLR . For the case where the aggressor UE is adjacent to the victim UEs, consider the
scenarios in Figure 5.1, 5.2 and 5.3, where a 20 MHz E-UTRA aggressor is adjacent to 3 victim UEs of 5 MHz, 10
MHz and 15 MHz E-UTRA systems respectively.
In Figure 5.1, all the UEs in the 5 MHz E-UTRA system will be affected by an ACLR of 30 + X - F ACLR . For the 10
MHz E-UTRA victims in Figure 5.2, two UEs will be affected by an ACLR of 30 + X - F ACLR whilst 1 UE will be
affected by a less severe ACLR of 43 + X- F ACLR . In the 15 MHz E-UTRA victim as shown in Figure 5.3, the UE next
to the band edge will be affected by an ACLR of 30 + X - F ACLR whilst the UE farthest from the band edge will be
affected by an ACLR of 43 + X - F ACLR . The victim UE of the 15 MHz E-UTRA occupying the centre RB (2nd from
band edge) is affected by 1/3 ACLR of 30 + X - F ACLR and 2/3 ACLR of 43 + X - F ACLR . This gives an ACLR of 34 +
X - F ACLR .
Using a similar approach for 15 MHz, 10 MHz and 5 MHz aggressor with a victim of smaller system bandwidth, the
ACLR affecting each of the 3 victim UEs can be determined. This is summarised in Table 5.2A. Here the value Y is
defined for victim UE, where ACLR = Y + X - F ACLR . UE1 is the UE adjacent to the aggressor, UE2 is located at the
centre and UE3 is furthest away from the aggressor.
3GPP
Release 100T 21 3GPP TR 36.942 V10.3.0 (2012-06)
30 + X 43 + X
Interfering UE
Victim UE
UE1 UE2 UE3
ACLR
16 RB 16 RB 16 RB
Table 5.2A: Value Y (ACLR = Y + X - F ACLR ) for larger aggressor bandwidth
Aggressor Victim: Value Y (dB): ACLR = (Y + X - F ACLR )

15 MHz 10 MHz 5 MHz 1.6 MHz
UE1 UE2 UE3 UE1 UE2 UE3 UE1 UE2 UE3 UE1 UE2 UE3
20 MHz 30 34 43 30 30 43 30 30 30 30 30 30
15 MHz 30 32 43 30 30 30 30 30 30
10 MHz 30 30 43 30 30 30
5 MHz 30 30 30
The victims in 10 MHz system under a 20 MHz aggressor experience slightly worse interference than the victims in 15
MHz system under a 20 MHz aggressor and therefore, we only need to consider the worst of the two cases. Hence,
from Table 5.2A, the total number of asymmetrical bandwidth coexistences can be reduced to 3 scenarios and they are
summarised in Table 5.2B. The performance of the other scenarios can be derived from these 3 base scenarios by
factoring in the FACLR factor in the ACLR.
Table 5.2B: Base scenarios (F ACLR = 0 dB)
Scenario System Bandwidth (MHz) Value Y (dB), ACLR = Y + X

Aggressor Victim UE1 UE2 UE3
1 15 10 30 32 43
2 20 10 30 30 43
3 20 5 30 30 30
An additional factor will be required to cater for the differences in UE transmit powers, which are dependent upon the
power control scheme used in Table 5.3. Given the power control scheme, a UE with higher bandwidth will transmit at
higher overall power (note: max UE transmit power remains the same). Thus, an aggressor with higher transmit power
than the aggressor in the base scenario needs to increase its ACLR. On the other hand, for an interference limited
environment, a victim with higher transmit power can overcome higher level of interference and hence demands a
relaxed ACLR from its aggressor. The differences in transmit powers are given in the power control factor, P ACLR and
it is dependent upon the CLx-ile of the aggressors and victims. P ACLR is given as:
P ACLR (dB) = (CLx-ile BaseAggressor - CLx-ile Aggressor ) + (CLx-ile Victim - CLx-ile BaseVictim )
Where, CLx-ile BaseAggressor and CLx-ile BaseVictim are the CLx-ile used by the aggressor and the victim respectively in the
base scenario in Table 5.2B. CLx-ile Aggressor and CLx-ile Victim are the CLx-ile of the aggressor and victim of interest
respectively. For example, using Power Control Set 1, for the scenario 10 MHz (aggressor) to 5 MHz (victim), CLx-
ile Aggressor = 112 and CLx-ile Victim = 115 dB. The base scenario used is Scenario 2 of Table 5.2B (20 MHz (aggressor) to
10 MHz (victim)). Hence, in this example, CLx-ile BaseAggressor = 109 dB and CLx-ile BaseVictim = 112 dB. Therefore,
PACLR = (109 – 112) + (115 – 112) = 0 dB.
The final ACLR as reference by the victim’s bandwidth is hence:
ACLR = Y + X – F ACLR + P ACLR
3GPP
Release 100T 22 3GPP TR 36.942 V10.3.0 (2012-06)
5.1.1.4.2 Uplink Asymmetrical Bandwidths ACIR (Aggressor with smaller bandwidth)

Consider the scenario in Figure 5.4, the interference experienced by UE1 is affected by 25% ACLR of 30 + X - F ACLR
and 75% ACLR of 43 + X - F ACLR . Since the victim bandwidth is larger than the aggressor, the interference
experienced by UE1 will caused by a mixture of ACLR 30 + X - F ACLR and ACLR 43 + X - F ACLR . For victim UE2 and
UE3, the interference is caused by ACLR 43 + X – F ALCR . The effective interference onto UE1 is dependent upon the
aggressor and victim bandwidths. If we take this level of interference and assumed that it is caused by an aggressor of
the same bandwidth (i.e. normalising the ACLR to the victim bandwidth) we have the normalised ACLR in Table 5.2C.
Interfering UE
Victim UE
ACLR
30 + X 43 + X 43 + X 43 + X
4 RB 4 RB 4 RB UE1 UE2
20 MHz E-UTRA
5 MHz E-UTRA
Figure 5.4: 5 MHz E-UTRA aggressor to 20 MHz E-UTRA victim
Table 5.2.C: Value Y (normalised ACLR = Y + X - FALCR) for victim UE1
Aggressor Victim: Value Y (dB): ACLR = (Y + X - F ACLR ) measured over B Victim

Bandwidth (MHz) 20 MHz 15 MHz 10 MHz 5 MHz
15 MHz 29.93 - - -
10 MHz 29.79 29.89 - -
5 MHz 29.39 29.59 29.79 -
1.6 MHz 28.02 28.48 28.99 29.56
The ACLR of the aggressor is likely to be larger than 43 + X dB after the 2nd ACLR and hence it is reasonable to
assume that the Y value of the normalised ACLR in Table 5.2C onto victim UE1 is close to 30 dB. This is similar to
the symmetrical bandwidth coexistence scenario where the first UE is affected by an ACLR of 30 + X dB. For victim
UE2 and UE3, the ACLR 43 + X is unrealistic. For scenario where the aggressor bandwidth is much smaller than the
victim bandwidth, the ACLR into UE2 and UE3 is going to be much larger than 43 + X. For example for 1.6 MHz E-
UTRA aggressor and 20 MHz E-UTRA victim, the interference into UE2 and UE3 is caused by the 13th ACLR (of 1.6
MHz aggressor) and above and this will likely be lower than the noise floor of the victim UE. Hence, the interference
experienced by UE2 and UE3 from an aggressor with a smaller bandwidth will not be worse than that from an aggressor
with a symmetrical bandwidth. Therefore, the ACLR value for coexistence between E-UTRA systems with
symmetrical bandwidth is sufficient for coexistence where the aggressor bandwidth is smaller than that of the victim.
5.1.1.4 Frequency re-use and interference mitigation schemes for E-UTRA

For initial simulations, 1/1 frequency re-use shall be used.
3GPP
Release 100T 23 3GPP TR 36.942 V10.3.0 (2012-06)
5.1.1.5 CQI estimation

It is assumed that the CQI including external system interference is available before the scheduling process. This
assumption is valid for the victim system only.
5.1.1.6 Power control modelling for E-UTRA and 3.84 Mcps TDD UTRA
No power control in downlink, fixed power per frequency resource block is assumed.
The following power control equation shall be used for the initial uplink (for E-UTRA and 3.84 Mcps TDD UTRA
employing Enhanced UL) coexistence simulations:
   CL 
γ
 
Pt = Pmax × min 1, max  Rmin ,   
   CLx −ile   
where P max is the maximum transmit power, R min is the minimum power reduction ratio to prevent UEs with good
channels to transmit at very low power level, CL is the path coupling loss defined as max{path loss-G_Tx-G_Rx,
MCL}, where path loss is propagation loss plus shadowfading, G_TX is the transmitter antenna gain in the direction of
the receiver, G_RX is the receiver antenna gain in the direction of the transmitter and CL x-ile is the x-percentile CL value.
With this power control equation, the x percent of UEs that have the highest coupling loss will transmit at P max . Finally,
0<γ<=1 is the balancing factor for UEs with bad channel and UEs with good channel:
The parameter sets for power control are specified in table 5.3.
Table 5.3: Power control algorithm parameter
Parameter Gamma CLx-ile

set 20 MHz 15 MHz 10 MHz 5 MHz
bandwidth bandwidth bandwidth bandwidth
Set 1 1 109 110 112 115
Set 2 0,8 TBD TBD 129 133
Further discussion and alignment concerning power control algorithms may be required after initial simulation results
and further inputs from RAN WG1 are available
5.1.1.7 SIR target requirements for simulated services

For E-UTRA, shifted and truncated Shannon bound curves as specified in Annex A.1 shall be used.
In the downlink, UTRA 3.84 Mcps TDD shall use HSDPA since most 3.84Mcps TDD deployments service data traffic.
A shifted and truncated Shannon bound curves described in Annex A.3 shall be used.
In the uplink, UTRA 3.84 Mcps TDD shall use Enhanced UL with data traffic. The shifted and truncated Shannon
bound curve used for E-UTRA uplink in Annex A.1 shall be used.
For E-UTRA TDD (LCR TDD frame structure based) shifted and truncated Shannon bound curves as specified in
Annex A.4 shall be used.
5.1.1.8 Number of required snapshots

The number of snapshots shall be chosen such to obtain sufficient statistical property of the results.
5.1.1.9 Simulation output

Simulation results for E-UTRA as victim shall be presented in terms of throughput reduction in percent relative to the
reference throughput without external interference vs. ACIR, separately for all UE and for the 5% throughput CDF UE.
All the generated statistics (e.g. bitrates) are instantaneous distributions on sub frame basis, not on a per-session basis.
I.e. the instantaneous bit rates need to be averaged in order to obtain the session average UE throughput.
3GPP
Release 100T 24 3GPP TR 36.942 V10.3.0 (2012-06)
Simulation results for UTRA FDD as victim shall be presented in terms of capacity reduction vs. ACIR. Capacity is
defined by the number of satisfied speech users.
Simulation results for UTRA 3,84 Mcps TDD as victim shall be presented in terms of throughput reduction in percent
relative to the reference throughput without external interference vs. ACIR
5.1.2 Simulation description

Uplink and Downlink are simulated independently. Degradation of victim system will be obtained by comparing
capacity/throughput simulation results of single operator scenario (without external interference) to the multi operator
case.
In the following sections the principle downlink simulation flows are described, taking the current simulation
assumptions into account.
For TDD simulations, both TDD networks (aggressor and victim) are synchronised together and have a common
downlink/uplink resource allocation.
5.1.2.1 Downlink E-UTRA interferer UTRA victim

1. Run UTRA snapshot simulator procedure [3]. E-UTRA BS TX power is set to the defined maximum TX power
(assumes all RB in use). All E-UTRA base stations are considered as a source of other system interference
(Iother). Iother = sum over all other system cells (interference power into UTRA bandwidth including ACIR)
2. Collect statistics.
The UTRA 3.84 Mcps TDD victim are synchronised and uses HSDPA service. The simulation procedure shall be the
same as that in Section 5.1.2.2 (Downlink E-UTRA interferer E-UTRA victim). Here, the CQI value in Step 2 (of
Section 5.1.2.2) shall be calculated based on per resource unit (timeslot × code) instead of per resource block.
5.1.2.2 Downlink E-UTRA interferer E-UTRA victim

For i=1:# of snapshots
1. Distribute terminals randomly throughout the system area such that to each cell within the HO margin of 3 dB
the same number K of users is allocated.
2. Calculate DL CQI for each UE. The CQI value per resource block is equal to C(RB)/I(RB), where:
• C(RB) = power of resource block * max (pathloss-G_Tx-G_Rx, MCL)
• I(RB) = sum over all other cells (power of resource block * max (pathloss-G_Tx-G_Rx, MCL)) + sum
over all other system cells (interference power into this resource block including ACIR) + N
• Note: in case of the 5 MHz and 10 MHz E-UTRA victim case, the BS ACLR (ACIR) is modelled as
flat, i.e. the same ACIR is used for all RB.
3. Perform PS operation for all cells:
• Loop over all cells
o Loop over all UE attached to the cell
 Select the next UE to be scheduled based on the scheduling metric (i.e. randomly for
Round Robin).
4. Calculate actual intra/inter system interference to get the actual C/I and bit rates for each UE.
• Use the actual C/I to throughput mapping (Annex A) to determine the obtained throughput for the UE.
• Note: the actual C/I value of a scheduled RB is equal to the CQI value calculated in step 2.
3GPP
Release 100T 25 3GPP TR 36.942 V10.3.0 (2012-06)
5.1.2.3 Uplink E-UTRA interferer UTRA victim

o Loop over all UEs attached to the cell
Round Robin)
 Pick 4 RB among the “not scheduled” ones and mark it as “scheduled”
   CL   
γ
 Set UE transmit power to Pt = Pmax × min   
1, max  R ,
min   
   CLx −ile   
3 Run UTRA snapshot simulator procedure [3]. All E-UTRA terminals are considered as a source of other system
interference (Iother). Iother = sum over all other system terminals (interference power into UTRA bandwidth
including ACIR).
4 Collect statistics.
For UTRA 3.84 Mcps TDD victim using Enhanced Uplink, the system TDD victim shall be synchronised and
simulation procedure shall be the same as that in Section 5.1.2.4 (Uplink E-UTRA interferer E-UTRA victim).
5.1.2.4 Uplink E-UTRA interferer E-UTRA victim

o Loop over all UE attached to the cell
Round Robin)
 Pick 8 RB among the “not scheduled” ones and mark it as “scheduled”
   CL 
γ
 
 Set UE transmit power to Pt = Pmax × min 
 1, max  Rmin ,   
   CLx −ile   
3. Calculate actual intra/inter system interference to get the actual C/(I+N) and bit rates for each UE.
• Use the actual C/(I+N) to throughput mapping as specified in Annex A to determine the obtained
throughput for the UE.
3GPP
Release 100T 26 3GPP TR 36.942 V10.3.0 (2012-06)
6 System scenarios
This chapter contains the system scenarios defined based upon the models described above designed for the interference
studies, RRM studies etc
6.1 Co-existence scenarios

Table 6.1 summarizes the proposed initial simulation scenarios. This list is tentative and represents the actual status of
the discussion. The list will be reviewed when the work on the simulation scenarios progresses. Uncoordinated
deployment is assumed for all these simulation scenarios.
Table 6.1; Summary of simulation scenarios
Aggressor Victim Simulation Environment Cell Priority

system system frequency Range
10 MHz E-UTRA 10 MHz E- 2000 MHz Urban Area 500 m high
UTRA
5 MHz E-UTRA 20 MHz E- 2000 MHz Urban Area 500 m lower
UTRA
5 MHz E-UTRA UTRA 2000 MHz Urban Area 500 m high
[1.25] MHz E- GERAN 900 MHz Rural Area 2000 m lower
UTRA
20 MHz E-UTRA UTRA 2000 MHz Urban Area 500 m lower
1.6 MHz E-UTRA UTRA 1.6MHz 2000 MHz Urban Area 500 m high
For high priority simulation scenarios, it was decided to simulate scenarios with the following priority:
- 5MHz E-UTRA – UTRA (victim), downlink
- 10MHz E-UTRA – 10MHz E-UTRA (victim), downlink
- 10MHz E-UTRA – 10MHz E-UTRA (victim), uplink
- 5MHz E-UTRA – UTRA (victim), uplink
- 1.6MHz E-UTRA –UTRA 1.6MHz (victim), downlink
- 1.6MHz E-UTRA –UTRA 1.6MHz (victim), uplink
7 Results
7.1 Radio reception and transmission

7.1.1 FDD coexistence simulation results
7.1.1.1 ACIR downlink 5MHz E-UTRA interferer – UTRA victim

Simulations are based on the following assumptions:
Aggressor system: 5 MHz E-UTRA
Victim system: UTRA FDD
Simulation frequency: 2000 MHz
Environment: Macro Cell, Urban Area, uncoordinated deployment
3GPP
Release 100T 27 3GPP TR 36.942 V10.3.0 (2012-06)
Cell Range 500 m
Simulation results are presented in table 7.1 and figure 7.1.
Table 7.1: UTRA FDD downlink capacity loss
ACIR Nokia Siemens Huawai Motorola Ericsson Lucent DoCoMo Qualcom average
(dB) (R4- (R4- (R4- (R4- (R4- (R4- (R4- m (R4- d
060375) 060379) 060448) 060461) 060592) 061134) 060967) 070036
25 7,5 % 11,30 % 4,78 % 17,5 % 8% 6,7 % 12,6 % 10,18 % 9,82 %
30 3,2 % 5,40 % 1,43 % 7% 3% 2,3 % 5,7 % 3,84 % 3,98 %
35 1,8 % 2,51 % 0,16 % 2,5 % 1,2 % 0,7 % 2,2 % 1,31 % 1,55 %
40 0,8 % 1,07 % 0,08 % 1% 0,5 % 0,1 % 0,7 % 0,39 % 0,58 %
45 0,5 % 0% 0,5 % 0,4 % 0,35 %
20,00
18,00
UTRA DL capacity loss (%)
16,00 Nokia (R4-060375)

Siemens (R4-060379)
14,00
Huaw ei (R4-060448)
12,00 Motorola (R4-060461)
10,00 Ericsson (R4-060592)
Lucent (R4-061134)
8,00
DoCoMo (R4-060967)
6,00 Qualcomm (R4-070036)
4,00 averaged
2,00
0,00
25 30 35 40 45
ACIR
Figure 7.1: UTRA FDD capacity loss
7.1.1.2 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA victim

Victim system: 10 MHz E-UTRA
Cell Range 500 m
Simulation results for average E-UTRA downlink throughput loss are presented in table 7.2 and figure 7.2. Simulation
results for 5% CDF throughput E-UTRA throughput loss are presented in table 7.3 and figure 7.3.
3GPP
Release 100T 28 3GPP TR 36.942 V10.3.0 (2012-06)
Table 7.2: Average E-UTRA downlink throughput loss
ACIR Siemens Huawai Motorola Ericsson DoCoMo Lucent Qualcomm averaged

(dB) (R4- (R4- (R4- (R4- (R4- (R4- (R4-
060748) 061003) 060462) 061071) 060967) 061134) 061342)
15 12,29 % 12,63 % 12,56 % 13,67 % 12,79 %
20 6,31 % 6,51 % 7% 6,66 % 6,6 % 7,32 % 6,50 % 6,73 %
25 3,1 % 3,17 % 3,5 % 3,28 % 3,2 % 3,65 % 3,10 % 3,32 %
30 1,51 % 1,34 % 1,5 % 1,49 % 1,4 % 1,68 % 1,40 % 1,49 %
35 0,67 % 0,46 % 0,5 % 0,62 % 0,6 % 0,7 % 0,50 % 0,59 %
40 0,30 % 0,11 % 0,25 % 0,24 % 0,2 % 0,25 % 0,20 % 0,23 %
45 0,11 % 0,1 % 0,08 % 0,07 % 0,09 %
50 0,03 % 0% 0,03 % 0% 0,02 %
16,00
average E-UTRA DL throughput loss (%)
14,00
12,00 Siemens (R4-060748)
Huaw ei (R4-061003)
10,00 Motorola (R4-060462)
Ericsson (R4-061071)
8,00
DoCoMo (R4-060967)
6,00 Lucent (R4-061134)

Qualcomm (R4-061342)
4,00 averaged
2,00
0,00
15 20 25 30 35 40 45 50
ACIR
Figure 7.2: average E-UTRA downlink throughput loss
Table 7.3: 5% CDF E-UTRA downlink throughput loss
ACIR Siemens Huawei Motorola Ericsson DoCoMo Lucent Qualcomm (5% CDF)
(dB) (R4- (R4- (R4- (R4- (R4- (R4- averaged
060749) 061003) 061071) 060967) 061134) 061342)
15 58,3 % 100 % 58,61 % 99,99 % 79,23 %
20 35,08 % 66,86 % 22,64 % 30,91 % 28,3 % 36,75 % 27,50 % 36,76 %
25 20,15 % 17,76 % 2,52 % 14,14 % 13,4 % 17,41 % 13,00 % 14,23 %
30 11,62 % 6,18 % 0,84 % 6,11 % 5,8 % 7,03 % 5,60 % 6,26 %
35 5,56 % 2,64 % 0,28 % 2,24 % 2,4 % 2,57 % 2,10 % 2,62 %
40 1,92 % 2,24 % 0,01 % 0,95 % 0,8 % 0,78 % 0,70 % 1,12 %
45 0,53 % 0,23 % 0,27 % 0,34 %
50 0,12 % 0,07 % 0% 0,06 %
3GPP
Release 100T 29 3GPP TR 36.942 V10.3.0 (2012-06)
100,00
5% CDF E-UTRA DL throughput loss (%
90,00
80,00
Siemens (R4-060749)
70,00 Huaw ei (R4-061003)
60,00 Motorola
50,00
DoCoMo (R4-060967)
40,00 Lucent (R4-061134)
30,00 Qualcomm (R4-061342)

(5% CDF) averaged
20,00
10,00
0,00
15 20 25 30 35 40 45 50
ACIR
Figure 7.3: 5% CDF E-UTRA downlink throughput loss
7.1.1.3 ACIR uplink 5MHz E-UTRA interferer – UTRA victim

Victim system: UTRA FDD
Cell Range 500 m
Simulation results are presented in table 7.3a and figure 7.3a for power control parameter set 1 and in table 7.3b and
figure 7.3b for E-UTRA power control parameter set 2 respectively. E-UTRA power control parameter sets are
specified in section 5.1.1.6.
Table 7.3a: UTRA FDD uplink capacity loss for E-UTRA power control set 1
ACIR NTT Motorola Ericsson Panasonic Siemens Qualcomm Alcatel- Nokia PC set 1
offset DoCoMo (R4- (R4- (R4- (R4- (R4- Lucent (R4- averaged
(dB) (R4- 061230) 061319) 061197) 061303) 070036) (R4- 070235)
061145) 070096)
-15
-10 100 % 100%
-5 75,80 % 100,00 % 78,90 % 100,00 82,00 % 87,34 %
%
0 39,50 % 20,30 % 42,90 % 17,50 % 35,29 % 49,00 % 45,30 % 29,00 % 34,85 %
5 12,60 % 5,90 % 13,60 % 6,60 % 12,37 % 14,20 % 14,40 % 13,00 % 11,58 %
10 3,3 % 2% 4,3 % 1,1 % 3,35 % 4,9 % 4,4 % 6,0 % 3,67 %
15 1,4 % 1,11 % 1,8 % 1,3 % 3,0 % 1,72 %
20 0,32 % 0,4 % 0,36 %
3GPP
Release 100T 30 3GPP TR 36.942 V10.3.0 (2012-06)
120,00
100,00 NTT DoCoMo (R4-061145)

UTRA UL capacity loss (%)
Motorola (R4-061230)
80,00 Ericsson (R4-061319)
Panasonic (R4-061197)
60,00 Siemens (R4-061303)
Alcatel-Lucent (R4-070096)
40,00
Nokia (R4-070235)
PC set 1 averaged
20,00
0,00
-15 -10 -5 0 5 10 15
ACIR offset
Figure 7.3a: UTRA FDD uplink capacity loss for E-UTRA power control set 1
Table 7.3b: UTRA FDD uplink capacity loss for E-UTRA power control set 2
ACIR NTT Motorola Ericsson Panasonic Siemens Qualcomm Alcatel- Nokia PC set 2
offset DoCoMo (R4- (R4- (R4- (R4- (R4- Lucent (R4- averaged
(dB) (R4- 061230) 061319 061197) 061303) 070036) (R4- 070235)
061145) 070096)
-15 100,00 % 89,10 % 57,00 % 82,03 %
-10 22,90 % 13,90 % 34,30 % 21,50 % 23,11 % 30,90 % 34,80 % 20,00 % 25,18 %
-5 7,50 % 4,40 % 10,90 % 5,20 % 7,46 % 9,80 % 8,80 % 8,00 % 7,76 %
0 2,40 % 1,10 % 3,40 % 1,92 % 2,34 % 3,30 % 3,00 % 4,00 % 2,68 %
5 0,80 % 0,40 % 1,10 % 0,72 % 0,86 % 1,20 % 0,90 % 1,00 % 0,87 %
10 0,3 % 0,3 % 0,21 % 0,27 % 0,2 % 0,3 % 0,26 %
15 0,1 % 0,09 % 0% 0,2 % 0,10%
20 0,04 % 0% 0,02 %
3GPP
Release 100T 31 3GPP TR 36.942 V10.3.0 (2012-06)
120,00
100,00 NTT DoCoMo (R4-061145)

UTRA UL capacity loss (%)
80,00 Ericsson (R4-061319
60,00 Siemens (R4-061303)
40,00
Nokia (R4-070235)
PC set 2 averaged
20,00
0,00
-15 -10 -5 0 5 10 15
ACIR offset
Figure 7.3b: UTRA FDD uplink capacity loss for E-UTRA power control set 2
7.1.1.4 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA victim

Cell Range 500 m
Simulation results for average E-UTRA uplink throughput loss are presented in table 7.3c and figure 7.3c for power
control parameter set 1 and in table 7.3d and figure 7.3d for E-UTRA power control parameter set 2 respectively.
Simulation results for 5% CDF throughput E-UTRA throughput loss are presented in table 7.3e and figure 7.3e for
power control parameter set 1 and in table 7.3f and figure 7.3f for E-UTRA power control parameter set 2 respectively.
E-UTRA power control parameter sets are specified in section 5.1.1.6.
Table 7.3c: Average E-UTRA uplink throughput loss for power control set 1
ACIR NTT Motorola Siemens Ericsson Panason Fujitsu Nokia Qualcom Alcatel- PC set 1
offset DoCoMo (R4- (R4- (R4- ic (R4- (R4- (R4- m (R4- Lucent averaged
(dB) (R4- 061231) 061349) 061319 061197) 061259) 061306) 061343) (R4-
061146) 070096)
-15 19,00 % 18,03 % 18,10 % 18,80 % 16,40 % 17,32 % 17,94 %
-10 10,20 % 9,40 % 9,9 % 9,60 % 11,26 % 10,10 % 9,60 % 10,30 % 9,55 % 9,99 %
-5 5,00 % 4,50 % 4,67 % 4,70 % 5,41 % 4,90 % 5,10 % 5,00 % 4,69 % 4,89 %
0 2,30 % 1,90 % 1,98 % 2,00 % 2,47 % 2,20 % 2,50 % 2,10 % 2,08 % 2,17 %
5 1,00 % 0,80 % 0,66 % 0,80 % 1,02 % 0,90 % 1,10 % 0,90 % 0,84 % 0,89 %
10 0,40 % 0,30 % 0,20 % 0,39 % 0,30 % 0,40 % 0,40 % 0,31 % 0,34 %
15 0,10 % 0,00 % 0,14 % 0,11 % 0,09 %
20 0,05 % 0,04 % 0,05 %
3GPP
Release 100T 32 3GPP TR 36.942 V10.3.0 (2012-06)
20,00
average E-UTRA UL throughput loss (%)
18,00
NTT DoCoMo (R4-061146)
16,00
14,00 Siemens (R4-061349)
12,00 Ericsson (R4-061319

10,00
Fujitsu (R4-061259)
8,00 Nokia (R4-061306)
6,00 Qualcomm (R4-061343)

4,00
PC set 1 averaged
2,00
0,00
-15 -10 -5 0 5 10 15 20
ACIR offset
Figure 7.3c: Average E-UTRA uplink throughput loss for power control set 1
Table 7.3d: Average E-UTRA uplink throughput loss for power control set 2
offset DoCoMo (R4- (R4- (R4- ic (R4- (R4- (R4- m (R4- Lucent averaged
(dB) (R4- 061231) 061349) 061319 061197) 061259) 061306) 061343) (R4-
061146) 070096)
-15 14,20 % 12,9 % 12,50 % 15,10 % 11,20 % 13,12 % 13,17 %
-10 7,10 % 6,40 % 6,62 % 6,10 % 7,09 % 7,60 % 6,00 % 7,00 % 6,68 % 6,73 %
-5 3,20 % 2,80 % 2,97 % 2,70 % 3,14 % 3,50 % 2,90 % 3,00 % 3,03 % 3,03 %
0 1,30 % 1,10 % 1,07 % 1,10 % 1,30 % 1,50 % 1,30 % 1,30 % 1,25 % 1,25 %
5 0,50 % 0,50 % 0,11 % 0,40 % 0,49 % 0,60 % 0,60 % 0,50 % 0,47 % 0,46 %
10 0,20 % 0,20 % 0,10 % 0,17 % 0,20 % 0,20 % 0,20 % 0,17 % 0,18 %
15 0,10 % 0,00 % 0,06 % 0,06 % 0,06 %
20 0,02 % 0,02 % 0,02 %
16,00
average E-UTRA UL throughput loss (%)
14,00
12,00 Motorola (R4-061231)

Siemens (R4-061349)
10,00 Ericsson (R4-061319
8,00
Fujitsu (R4-061259)
6,00 Nokia (R4-061306)

4,00 Alcatel-Lucent (R4-070096)
PC set 2 averaged
2,00
0,00
-15 -10 -5 0 5 10 15 20
ACIR offset
Figure 7.3d: Average E-UTRA uplink throughput loss for power control set 2
3GPP
Release 100T 33 3GPP TR 36.942 V10.3.0 (2012-06)
Table 7.3e: 5% CDF E-UTRA uplink throughput loss for power control set 1
offset DoCoMo (R4- (R4- (R4- ic (R4- (R4- (R4- m (R4- Lucent (5%
(dB) (R4- 061231) 061349) 061319 061197) 061259) 061306) 061343) (R4- CDF)
061146) 070096) averaged
-15 42,20 % 28,86 % 41,40 % 37,80 % 47,00 % 38,51 % 39,30 %
-10 17,50 % 15,80 % 10,32 % 17,90 % 29,95 % 17,60 % 21,00 % 17,00 % 15,25 % 18,04 %
-5 6,90 % 5,60 % 1,7 % 6,50 % 9,91 % 6,90 % 6,10 % 6,40 % 5,78 % 6,20 %
0 2,00 % 1,10 % 0,11 % 2,80 % 2,58 % 2,10 % 2,20 % 2,10 % 1,80 % 1,87 %
5 0,60 % 0,50 % 0,01 % 1,20 % 0,58 % 0,50 % 0,50 % 0,80 % 0,57 % 0,58 %
10 0,20 % 0,06 % 0,20 % 0.13 % 0,10 % 0,30 % 0,30 % 0,17 % 0,19 %
15 0,10 % 0,00 % 0,03 % 0,04 % 0,04 %
20 0,01 % 0,02 % 0,02 %
50,00
5% CDF E-UTRA UL throughput loss (%
45,00
40,00
35,00 Siemens (R4-061349)
30,00 Ericsson (R4-061319

25,00
Fujitsu (R4-061259)
20,00 Nokia (R4-061306)
15,00 Qualcomm (R4-061343)

10,00
PC set 1 (5% CDF) averaged
5,00
0,00
-15 -10 -5 0 5 10 15 20
ACIR offset
Figure 7.3e: 5% CDF E-UTRA uplink throughput loss for power control set 1
Table 7.3f: 5% CDF E-UTRA uplink throughput loss for power control set 2
offset DoCoMo (R4- (R4- (R4- ic (R4- (R4- (R4- m (R4- Lucent (5%
(dB) (R4- 061231) 061349) 061319 061197) 061259) 061306) 061343) (R4- CDF)
061146) 070096) averaged
-15 34,40 % 34,11 % 30,70 % 32,60 % 29,30 % 29,16 % 31,71 %
-10 15,30 % 11,80 % 17,19 % 13,10 % 18,52 % 14,30 % 13,40 % 15,10 % 12,09 % 14,53 %
-5 5,80 % 4,40 % 5,05 % 4,70 % 5,68 % 5,20 % 7,20 % 5,60 % 4,50 % 5,35 %
0 1,70 % 1,30 % 1,62 % 1,10 % 1,14 % 1,40 % 2,20 % 1,80 % 1,19 % 1,49 %
5 0,70 % 0,40 % 0,08 % 0,40 % 0,24 % 0,30 % 0,50 % 0,60 % 0,40 % 0,40 %
10 0,20 % 0,10 % 0,20 % 0,09 % 0,05 % 0,10 % 0,09 % 0,14 %
15 0,00 % 0,00 % 0,02 % 0,00 % 0,01 %
20 0,01 % 0,00 % 0,01 %
3GPP
Release 100T 34 3GPP TR 36.942 V10.3.0 (2012-06)
35,00
5% CDF E-UTRA UL throughput loss (%
30,00 NTT DoCoMo (R4-061146)

25,00 Siemens (R4-061349)
Ericsson (R4-061319
20,00 Panasonic (R4-061197)
Fujitsu (R4-061259)
15,00
Nokia (R4-061306)
10,00
PC set 2 (5% CDF) averaged
5,00
0,00
-15 -10 -5 0 5 10 15 20
ACIR offset
Figure 7.3f: 5% CDF E-UTRA uplink throughput loss for power control set 2
7.1.2 TDD coexistence simulation results
7.1.2.1 ACIR downlink 5MHz E-UTRA interferer – UTRA 3.84 Mcps TDD victim
Victim system: UTRA 3,84 Mcps TDD using HSDPA
Cell Range 500 m
Simulation results for average UTRA 3,84Mcps TDD downlink throughput loss are presented in table 7.4 and figure 7.4.
Simulation results for 5% CDF UTRA 3,84Mcps TDD downlink throughput loss are presented in table 7.5 and figure
7.5.
Table 7.4: average UTRA 3,84Mcps TDD downlink throughput loss
ACIR IP Wireless Ericsson

(dB) (R4- (R4-
060813) 061071)
15 12,56 %
20 6,66 %
25 5,2 % 3,28 %
30 2,8 % 1,49 %
35 1,3 % 0,62 %
40 0,7 % 0,24 %
45 0% 0,08 %
50 0,03 %
3GPP
Release 100T 35 3GPP TR 36.942 V10.3.0 (2012-06)
14
average UTRA TDD throughput loss (%)
12
10
8 IP Wireless (R4-060813)
6
0
15 20 25 30 35 40 45 50
ACIR
Figure 7.4: average UTRA 3,84Mcps TDD downlink throughput loss
Table 7.5: 5% CDF UTRA 3,84Mcps TDD downlink throughput loss

(dB) (R4- (R4-
060813) 061071)
15 58,61 %
20 30,91 %
25 20,3 % 14,14 %
30 10,8 % 6,11 %
35 5,4 % 2,24 %
40 2,6 % 0,95 %
45 0,85 % 0,23 %
50 0,07 %
3GPP
Release 100T 36 3GPP TR 36.942 V10.3.0 (2012-06)
70
5%CDF UTRA TDD throughput loss (%)
60
50
30
20
10
0
15 20 25 30 35 40 45 50
ACIR
Figure 7.5: 5% CDF UTRA 3,84Mcps TDD downlink throughput loss
7.1.2.2 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim
Cell Range 500 m
Simulation results for average E-UTRA TDD downlink throughput loss are presented in table 7.6 and figure 7.6.
Simulation results for 5% CDF E-UTRA TDD downlink throughput loss are presented in table 7.7 and figure 7.7.
Table 7.6: average E-UTRA TDD downlink throughput loss

(dB) (R4- (R4-
060813) 061071)
15 12,56 %
20 6,66 %
25 5,3 % 3,28 %
30 2,8 % 1,49 %
35 1,4 % 0,62 %
40 0,7 % 0,24 %
45 0,2 % 0,08 %
50 0,03 %
3GPP
Release 100T 37 3GPP TR 36.942 V10.3.0 (2012-06)
14
12
E-UTRA DL throughput loss (%
10
6
0
15 20 25 30 35 40 45 50
ACIR
Figure 7.6: average E-UTRA TDD downlink throughput loss
Table 7.7: 5% CDF E-UTRA TDD downlink throughput loss

(dB) (R4- (R4-
060813) 060880)
15 58,61 %
20 30,91 %
25 20,3 % 14,14 %
30 10,8 % 6,11 %
35 5,4 % 2,24 %
40 2,6 % 0,95 %
45 0,85 % 0,23 %
50 0,07 %
3GPP
Release 100T 38 3GPP TR 36.942 V10.3.0 (2012-06)
70
60
E-UTRA DL throughput loss (%
50
40
IP Wireless (R4-060813)
30
20
10
0
15 20 25 30 35 40 45 50
ACIR
Figure 7.7: 5% CDF E-UTRA TDD downlink throughput loss
7.1.2.3 ACIR downlink 1.6 MHz E-UTRA interferer – UTRA 1.28 Mcps TDD victim
Aggressor system: 1.6 MHz E-UTRA (LCR TDD frame structure based) using 4 RB, BS output power 35dBm
and 43dBm
Victim system: UTRA 1.28 Mcps TDD using smart antennas as specified in Annex B
Environment: Macro Cell, Urban Area, coordinated and uncoordinated deployment
Cell Range 500 m
Simulation results are presented in figure 7.8, figure 7.8a, figure 7.9 and figure 7.9a. Co-existence requirements derived
from these results require smart antennas at the UTRA 1.28 Mcps TDD system.
3GPP
Release 100T 39 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.8: Capacity loss of UTRA 1.28 Mcps TDD DL with 1.6MHz E-UTRA DL aggressor, 35dBm BS
output power, coordinated deployment
Figure 7.8a: Capacity loss of UTRA 1.28 Mcps TDD DL with 1.6MHz E-UTRA DL aggressor, 43dBm BS
output power, coordinated deployment
3GPP
Release 100T 40 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.9: Capacity loss of UTRA 1.28 Mcps TDD DL with 1.6MHz E-UTRA DL aggressor, 35dBm BS
output power, uncoordinated deployment
Figure 7.9a: Capacity loss of UTRA 1.28 Mcps TDD DL with 1.6MHz E-UTRA DL aggressor, 43dBm
BS output power, uncoordinated deployment
3GPP
Release 100T 41 3GPP TR 36.942 V10.3.0 (2012-06)
7.1.2.4 ACIR uplink 5MHz E-UTRA interferer – UTRA 3.84 Mcps TDD victim
Victim system: UTRA 3,84 Mcps TDD using Enhanced Uplink
Cell Range 500 m
Simulation results for UTRA 3,84Mcps TDD uplink throughput loss are presented in table 7.8 (Power Control
Parameter Set 1) and table 7.9 (Power Control Parameter Set 2). The results are also plotted in figure 7.10 (Average
Throughput Loss) and figure 7.11 (5% CDF Throughput Loss).
Editors Note: Results where presented at RAN4#41 but need to be verified. Blank tables and figure titles are included
here to keep consistent numbering.
Table 7.8: UTRA 3,84 Mcps TDD uplink throughput loss (average & 5% CDF) for Parameter Set 1
X (dB) ACIR = 30 + Throughput Loss (%) – Parameter Set 1 (Gamma=1, CLx-ile=115)

X (dB) IPWireless (R4-070037) Ericsson (R4-061340)
Average 5% CDF Average 5% CDF
-15 15 13.6 51.8 16.7 53.4
-10 20 7.3 20.8 8.6 21.4
-5 25 3.6 7.2 4.1 8.2
0 30 1.7 2.5 1.7 2.7
5 35 0.6 0.8 0.6 0.7
10 40 0.2 0 0.2 0
15 45 0 0 0 0
20 50 0 0 0 0
Table 7.9: UTRA 3,84 Mcps TDD uplink throughput loss (average & 5% CDF) for Parameter Set 2
X (dB) ACIR = 30 + Throughput Loss (%) - Parameter Set 2 (Gamma=0.8, CLx-ile=133)

-15 15 12.2 33.4 13 35.1
-10 20 5.7 13.8 6.4 15.5
-5 25 2.5 4.4 2.8 5.6
0 30 1.1 1.0 1.1 1.9
5 35 0.3 0.2 0.4 0.5
10 40 0 0 0.1 0.2
15 45 0 0 0 0
20 50 0 0 0 0
3GPP
Release 100T 42 3GPP TR 36.942 V10.3.0 (2012-06)
IPWireless (R4-070037) PC Set 1 Ericsson (R4-061340) PC Set 1

18
16
Average UTRA TDD Throughput Loss (%)
14
12
10
0
15 20 25 30 35 40 45 50
ACIR (ACLR=30+X) (dB)
Figure 7.10: average UTRA 3,84 Mcps TDD uplink throughput loss

60
5% CDF UTRA TDD Throughput Loss (%)
50
40
30
20
10
0
15 20 25 30 35 40 45 50
Figure 7.11: 5% CDF UTRA 3,84 Mcps TDD uplink throughput loss
3GPP
Release 100T 43 3GPP TR 36.942 V10.3.0 (2012-06)
7.1.2.5 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim
Cell Range 500 m
Simulation results for average E-UTRA TDD uplink throughput loss are presented in table 7.10 (Power Control
Parameter Set 1) and table 7.11 (Power Control Parameter Set 2). The results are also plotted in figure 7.12 (average
throughput loss) and figure 7.13 (5% CDF throughput loss).
Table 7.10: E-UTRA TDD uplink throughput loss (average & 5% CDF) – Parameter Set 1
X (dB) ACIR = 30 + Throughput Loss (%) - Parameter Set 1 (Gamma=1, CLx-ile=112)

-15 15 18.1 41.4
-10 20 12 20 9.6 17.9
-5 25 6.9 12 4.7 6.5
0 30 3.6 5.8 2.0 2.8
5 35 1.8 2.6 0.8 1.2
10 40 0.8 1.1 0.2 0.2
15 45 0.3 0.4 0.0 0.0
20 50 0.1 0.2 0.0 0.0
Table 7.11: E-UTRA TDD uplink throughput loss (average & 5% CDF) – Parameter Set 2
X (dB) ACIR = 30 + Throughput Loss (%) - Parameter Set 2 (Gamma=0.8, CLx-ile=129)

-15 15 12.5 30.7
-10 20 10.2 14 6.1 13.1
-5 25 5.6 7.8 2.7 4.7
0 30 2.7 3.9 1.1 1.1
5 35 1.4 2.1 0.4 0.4
10 40 0.7 1.1 0.1 0.2
15 45 0.3 0.6 0.0 0.0
20 50 0.2 0.2 0.0 0.0
3GPP
Release 100T 44 3GPP TR 36.942 V10.3.0 (2012-06)

20
18
Average E-UTRA TDD Throughput Loss (%)
16
14
12
10
0
15 20 25 30 35 40 45 50
Figure 7.12: average E-UTRA TDD uplink throughput loss
3GPP
Release 100T 45 3GPP TR 36.942 V10.3.0 (2012-06)

45
40
5% CDF E-UTRA TDD Throughput Loss (%)
35
30
25
20
15
10
0
15 20 25 30 35 40 45 50
Figure 7.13: 5% CDF E-UTRA TDD uplink throughput loss
7.1.2.6 ACIR uplink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim (LCR
frame structure based)
Aggressor system: 10 MHz E-UTRA (LCR TDD frame structure based)
Victim system: 10 MHz E-UTRA (LCR TDD frame structure based)
Cell Range 500 m
Link level performance is specified in Annex A.4. Simulation results for average E-UTRA uplink throughput loss are
presented in figure 7.14. Simulation results for 5% CDF E-UTRA uplink throughput loss are presented in figure 7.15.
3GPP
Release 100T 46 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.14: average E-UTRA TDD uplink throughput loss
Figure 7.15: 5% CDF E-UTRA TDD uplink throughput loss
7.1.2.7 ACIR downlink 10MHz E-UTRA interferer – 10MHz E-UTRA TDD victim (LCR
frame structure based)
Aggressor system: 10 MHz E-UTRA (LCR TDD frame structure based)
Victim system: 10 MHz E-UTRA (LCR TDD frame structure based)
3GPP
Release 100T 47 3GPP TR 36.942 V10.3.0 (2012-06)
Environment: Macro Cell, Urban Area
Cell Range 500 m
Link level performance is specified in Annex A.4. Simulation results for average E-UTRA downlink throughput loss
are presented in figure 7.16. Simulation results for 5% CDF E-UTRA downlink throughput loss are presented in figure
7.17.
Figure 7.16: average E-UTRA TDD downlink throughput loss, uncoordinated deployment
3GPP
Release 100T 48 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.17: 5% CDF E-UTRA TDD downlink throughput loss, coordinated and uncoordinated
deployment
7.1.3 Additional coexistence simulation results

In this section, additional co-existence simulation results are collected. Assumptions for these simulations may differ
from those described in section 5 of the present document.
7.1.3.1 ACIR downlink E-UTRA interferer – GSM victim

The key simulation parameters are summarized in table 7.12. The E-UTRA and system scenario parameters are as
described in section 5 of the present document for rural macro cell environment with un-coordinated base-station
deployment, and the GSM parameters are taken from [2] (Scenario_2: UMTS (macro)-GSM (macro) in rural area).
Different to the simulation assumptions in [2], no correction of LTE BS ACLR according to a spectrum mask was
applied and the interference was assumed “flat” across all GSM carriers. The GSM ACS was set such that the resulting
ACIR was dominated by the E-UTRA BS ACLR. For each ACIR value, E-UTRA base-stations transmit at maximum
power (in order to produce maximum adjacent channel interference) and GSM UE are continuously added until the
system is fully loaded. The success/failure status of a GSM UE is determined at a threshold of 0.5dB less than the
required SINR target [2]. Simulation results [14] are presented in figure 7.18
3GPP
Release 100T 49 3GPP TR 36.942 V10.3.0 (2012-06)
Table 7.12: Simulation parameters
Parameters E-UTRA GSM Notes

Uplink carrier frequency 900 MHz
band
Uplink System Bandwidth 1.25MHz 24 x 200kHz
Number of carriers 1 4 cells/12 frequencies
reuse, 2 carriers/sector
Environment Macro- Rural
Cell radius 1km cell range = 2 x radius
= 2km
Base-stations Un-coordinated distributed Offset located at the
edge of cell.
Transmission power max. of 43dBm Power controlled with UE
and max. of 43dBm
Network layout 36 cells (6x6), 108 sectors with wrap-around
80,00
70,00
60,00
GSM DL outage (%)
50,00
40,00 Siemens (R4-061288)
30,00
20,00
10,00
0,00
15 20 25 30 35 40 45 50
ACIR
Figure 7.19: GSM downlink outage
An analytical investigation of E-UTRA-GSM downlink coexistence is provided in [15]. In the [2] the aggressing UTRA
influence on GSM is modelled as constant ACIR over the whole GSM system bandwidth. The UTRA system load is
according to [2], i.e. 5% outage.
For an E-UTRA system the interference generated to the GSM system can be modelled in the same way. Thus for a 5
MHz E-UTRA system the interference to the adjacent channel can be considered to be constant over the whole 5 MHz
adjacent carrier. The other component of the ACIR in this case is the ACS of a GSM MS. In [2] this has been assumed
to be significantly larger than the ACLR of the UTRA system and thus the main contribution to the ACIR is the ACLR.
For coexistence with an E-UTRA aggressor and a UTRA victim the ACLR for EUTRA should be of the same order as
for UTRA. In [2] the ACLR for UTRA is assumed to be 50 dB.
Table 7.13: ACIR limit for 5% outage degradation in the GSM system for relevant system scenarios.
Numbers from [2]
Scenario 1 UMTS(macro) GSM(macro) Urban 500m cell radius, Uncoordinated 27-31 dB
Scenario 2 UMTS(macro) GSM(macro) Rural 5000m cell radius, Uncoordinated 26-29 dB
Scenario 5 UMTS(macro) GSM(micro) Urban, Uncoordinated 26-40 dB
3GPP
Release 100T 50 3GPP TR 36.942 V10.3.0 (2012-06)
The ACIR values obtained in [2] for which 5% outage degradation occurs are listed in Table 7.13.
The difference between a UTRA and E-UTRA system is that for coexistence studies the E-UTRA system is assumed to
use full power. However since the UTRA system has a reasonably high outage it will also use close to maximum power
and the difference between E-UTRA and UTRA should only be a few dB.
In summary: For E-UTRA requirements on ACLR for the eNodeB similar to the requirements on UTRA, i.e. around 50
dB, the performance degradation on a GSM system is less than 5% outage degradation. This is also confirmed by the
simulation results in figure 7.19. Thus the present coexistence scenario is not more constraining than the E-UTRA to E-
UTRA and E-UTRA to UTRA scenarios considered so far and need not be considered when setting E-UTRA
requirements.
In addition there are a number of factors that make the assumptions above slightly pessimistic:
• The interference in the neighboring channel has been assumed to be flat. In practical systems however it
falls off, which makes the GSM carriers distant from the E-UTRA carrier less interfered. This will
reduce the outage degradation.
• The E-UTRA system has been assumed to transmit at full power at all times. However this is rarely the
case in practical systems. Thus the interference is lower and the outage degradation less.
For E-UTRA systems with narrower bandwidth than 5 MHz, e.g. 1.6 MHz the power spectral density in the interfering
region is higher if we assume that the output power of an E-UTRA eNodeB is the same as for the 5 MHz system. The
increase is 5 dB which would increase the requirements in table 7.13 with 5 dB. The interference will affect fewer GSM
channels though since the fall off previously mentioned is steeper for a 1.6 MHz system.
7.1.3.2 ACIR uplink E-UTRA interferer – GSM victim

The key simulation parameters are summarized in table 7.14. The E-UTRA and system scenario parameters are as
described in section 5 of the present document for rural macro cell environment with un-coordinated base-station
deployment, and the GSM parameters are taken from [2] (Scenario_2: UMTS (macro)-GSM (macro) in rural area).
Simulations for two scenarios have been presented, (a) in [16] and (b) in [17]. Different to the simulation assumptions
in [2], no correction of LTE UE ACLR according to a spectrum mask was applied and the interference was assumed
“flat” across all GSM carriers. Consequently, the ACIR has been modelled as flat as well. The ACIR is here expressed
in dBc/1x375kHz (a) and dBc/4x375kHz (b) For each ACIR value, E-UTRA UEs are firstly added to the system until it
is fully loaded with 3 UEs/sector. Subsequently, GSM UEs are continuously added until the system is fully loaded. The
success/failure status of a GSM UE is determined at the threshold of 0.5dB less than the required SINR target [2].
Simulation results [16, 17] are presented in figure 7.19
3GPP
Release 100T 51 3GPP TR 36.942 V10.3.0 (2012-06)
Table 7.14: Simulation parameters
Parameters E-UTRA GSM Notes

Uplink carrier frequency 900 MHz
band
Uplink System Bandwidth (a) 1.25MHz (3 frequency (a) 24 x 200kHz
RBs with 1RB/UE = 3
UE/sector) (b) 12 x 200kHz
(b) 5MHz (12 frequency
RBs with 4RB/UE = 3
UE/sector)
Number of carriers 1 (a) 4 cells/12 frequencies
reuse, 2 carriers/sector
(b) 4 cells/12 frequencies

reuse, 1 carrier/sector
Environment Macro- Rural
Cell radius 1km cell range = 2 x radius
= 2km
Base-stations Un-coordinated distributed Offset located at the
edge of cell.
Transmission power max. of 24dBm, max. of 33dBm,
min. of -30dBm min. of 5dBm
Network layout 36 cells (6x6), 108 sectors with wrap-around
Power control PC set 1 as in section as in [2]
5.1.1.6
PLx −ile = 121dB
γ
=1
2
1,8
GSM Outage Increase (%)
1,6
1,4
Ericsson (R4-070390) 5 MHz
1,2
1 Siemens (R4-061304) 1.25 MHz
0,8
0,6
0,4
0,2
0
0 5 10 15 20 25 30 35 40 50
ACIR (dB)
Figure 7.19: GSM uplink outage
The results show that the outage increase in both cases (a) and (b)is negligible even for flat ACLR/ACS and very low
levels of ACIR.
7.1.3.3 Asymmetric coexistence 20 MHz and 5 MHz E-UTRA

3GPP
Release 100T 52 3GPP TR 36.942 V10.3.0 (2012-06)
Cell Range 500 m
Generalising from 5 MHz and 10MHz to the 20MHz bandwidth we make the following assumptions:
• 3 UEs per carrier for aggressor and victim
• The ACLR is expressed in dBc per bandwidth B occupied by the aggressing UE
• A 13dB ACLR improvement is assumed for frequency separations larger than B from the edge of the UE
occupied bandwidth.
The simulation results are given in Figure 7.20 and the numerical data are presented in Table 7.15.
20
20MHz->20MHz
18
20MHz->5MHz
16
loss in 5%-tile throughput [%]
14
12
10
0
10 20 30 40 50 60 70
ACIR [dB]
Figure 7.20: Loss in 5%-ile throughput versus ACIR [18]
Table 7.15: Numerical values [18]
ACIR (dB) loss in 5%-ile throughput (%)
20MHz -> 5MHz 20MHz -> 20MHz

15 67.1% 42.3%
20 33.1% 17.8%
25 12.8% 6.2%
30 4.4% 2.5%
35 1.3% 0.7%
40 0.3% 0.2%
45 0.1% 0.1%
We also note some effects when a 5 MHz E-UTRA system aggresses a 20 MHz E-UTRA system. Considering the case
where the victim network bandwidth is larger than the aggressing network bandwidth, the impact of the aggressing UEs
to the victim BS is lower than for the case of symmetric bandwidth, because the "shoulder" of the ACLR of the
immediately adjacent aggressing UE will cover a smaller bandwidth of the victim network. This case is therefore
uncritical.
3GPP
Release 100T 53 3GPP TR 36.942 V10.3.0 (2012-06)
7.1.3.4 Impact of cell range and simulation frequency on ACIR

The impact of cell range and simulation frequency is analysed by comparing downlink scenarios with simulation
frequency of 900MHz (1.25MHz system bandwidth) and 2GHz (10MHz system bandwidth) and cell ranges of 500m,
2000m and 5000m in urban and rural area environment.
For the 2GHz rural environment case 18dBi antenna gain and 45m antenna height were assumed. Propagation model for
the 2GHz rural environment case is according to section 4.5.3 modified for 2GHz and 45m antenna height with the
following formula:
L = 100,5 + 34,1log10 (R)
Where:
Figure 7.21 presents average system throughput loss in percent relative to the reference throughput without external
system interference. Figure 7.22 presents 5% CDF user throughput loss in percent relative to the reference throughput
without external system interference.
E-UTRA DL average system throughput loss vs ACIR
14
E-UTRA DL average system throughput loss [%]
12
10
0
15 20 25 30 35
ACIR [dB]
2GHz [10MHz], urban, 500m 900MHz [1.25MHz], urban, 500m 900MHz [1.25MHz], rural, 2000m
900MHz [1.25MHz], rural, 5000m 2GHz [10MHz], rural, 2000m 2GHz [10MHz], rural, 5000m
Figure 7.21: Average system throughput loss in downlink
3GPP
Release 100T 54 3GPP TR 36.942 V10.3.0 (2012-06)
5% CDF E-UTRA DL user throughput loss vs ACIR
60
5% CDF E-UTRA DL user throughput loss [%]
50
40
30
20
10
0
15 20 25 30 35
ACIR [dB]
2GHz [10MHz], urban, 500m 900MHz [1.25MHz], urban, 500m 900MHz [1.25MHz], rural, 2000m
900MHz [1.25MHz], rural, 5000m 2GHz [10MHz], rural, 2000m 2GHz [10MHz], rural, 5000m
Figure 7.22: 5% CDF user throughput loss in downlink
On the basis of the simulation results it can be assumed that the worst case scenario is 2GHz, urban environment, 500m
cell range.
7.1.3.5 Uplink Asymmetric coexistence TDD E-UTRA to TDD E-UTRA

Simulations are based on the base scenarios in Table 5.2B with following assumptions in Table 7.16:
Table 7.16: Simulation assumptions based on 3 base secnarios
Parameter Scenario 1 Scenario 2 Scenario 3

Aggressor’s Bandwidth 15 MHz 20 MHz 20 MHz
Victim’s Bandwidth 10 MHz 10 MHz 5 MHz
Frequency 2000 MHz
Environment Macro Cell, Urban Area, uncoordinated deployment
Cell range 500 m
FACLR 0 dB
Simulation results are presented in Table 7.17 and plotted in Figure 7.23 and 7.24 for the average throughput loss and
5% CDF throughput loss for Power Control Parameter Set 1. The symmetrical results of 10 MHz TDD E-UTRA to 10
MHz TDD E-UTRA are also plotted for reference.
3GPP
Release 100T 55 3GPP TR 36.942 V10.3.0 (2012-06)
Table 7.17: Simulation results for Power Control Set 1 (F ACLR = 0, P ACLR = 0)
ACIR (dB) Average Throughput Loss (%) 5% CDF Throughput Loss (%)
X 30 + X Scenario 1 Scenario 2 Scenario 3 Scenario 1 Scenario 2 Scenario 3
-15 15 26.0 31.5 47.9 64.3 73.5 89.1
-10 20 15.0 18.0 30.8 30.4 40.9 72.3
-5 25 6.9 10.1 18.2 11.0 16.0 38.5
0 30 3.3 4.9 9.1 4.1 5.8 13.3
5 35 1.4 2.3 4.6 1.0 1.7 5.5
10 40 0.2 1.2 2.4 0.7 0.5 1.7
15 45 0.0 0.5 0.6 0.4 0.2 0.3
20 50 0.0 0.0 0.0 0.0 0.0 0.0
10 MHz Sym (R4-061312) 10 MHz Sym (R4-061319) Scenario 1 Scenario 2 Scenario 3
50
45
Average E-UTRA TDD Throughput Loss (%)
40
35
30
25
20
15
10
0
10 15 20 25 30 35 40 45 50
ACLR = X + 30 (dB)
Figure 7.23: Average throughput loss (PC Set 1)
3GPP
Release 100T 56 3GPP TR 36.942 V10.3.0 (2012-06)
10 MHz Sym (R4-061312) 10 MHz Sym (R4-061319) Scenario 1 Scenario 2 Scenario 3
100
90
5% CDF E-UTRA TDD Throughput Loss (%)
80
70
60
50
40
30
20
10
0
10 15 20 25 30 35 40 45 50
ACLR = X + 30 (dB)
Figure 7.24: 5% CDF throughput loss (PC Set 1)
7.1.4 Base station blocking simulation results

Figure 7.25 and Figure 7.26 show the CDF curves of the total received power level in 10MHz bandwidth at the own
system base stations in other system operating frequency (blocking scenario) from all other system terminals, using
power control parameter set 1 and set 2, respectively. The signal from all own system terminals was decreased by 49dB
(assuming terminal noise floor of -30dBm/1MHz it is 49dBc/3MHz for a 24dBm terminal). The same simulator and
simulation assumptions were used as for coexistence studies in uplink for the E-UTRA system in 10MHz system
bandwidth.
3GPP
Release 100T 57 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.25: CDF of the total received power level at the own system base stations (10MHz) from all
other system terminals, PC set 1
3GPP
Release 100T 58 3GPP TR 36.942 V10.3.0 (2012-06)
Figure 7.26: CDF of the total received power level at the own system base stations (10MHz) from all
other system terminals, PC set 2
Total received power level was assumed here for simplicity, however it should be noted that this may be pessimistic as
the most relevant RX impairments are a nonlinear function of the blocker received power levels present at the receiver
input.
It is proposed the mean power of the interfering signal is equal to -43dBm which is a compromise between the 30dBm
Maximum Output Power terminals defined in TR 36.803 and the 24dBm assumption in TR 36.942 under worst case
MCL conditions.
7.2 RRM
8 Rationales for co-existence requirements
8.1 BS and UE ACLR

The metric for the degradation of a victim system by the presence of an interfering system on adjacent channel in the
present document is the capacity loss (for UTRA as victim) or throughput loss (for E-UTRA as victim) in dependence
of Adjacent Channel Interference Ratio (ACIR). ACIR is defined as
1
ACIR =
1 1
+
ACLR ACS
ACLR is the Adjacent Channel Leakage power Ratio of the interfering systems transmitter (specified as the ratio of the
mean power centred on the assigned channel frequency to the mean power centred on an adjacent channel frequency)
and ACS is the corresponding receiver requirement on Adjacent Channel Selectivity of the victim system receiver.
It is assumed that the capacity or throughput loss of the victim system shall not exceed 5%. It is also assumed that ACIR
is dominated by the UE ACLR.
8.1.1 Requirements for E-UTRA – UTRA co-existence

In this case UTRA sets some constraints as ACLR and ACS as E-UTRA would need to be deployed adjacent to both
UTRA and E-UTRA. The two scenarios are shown in figure 8.1
UTRA E-UTRA E-UTRA E-UTRA
UTRA deployed adjacent to E-UTRA by E-UTRA deployed adjacent to E-UTRA

either the same or different operator by either the same or different operators
Figure 8.1: E-UTRA deployment scenarios
BS ACLR can be obtained from downlink simulation results presented in section 7.1.1.1. For 5% UTRA capacity loss
an E-UTRA BS ACLR of at least 33dB is required. Assuming the legacy UTRA ACLR of 45dB for E-UTRA BS will
result in less than 3% UTRA capacity loss.
UE ACLR can be obtained from uplink simulation results presented in section 7.1.1.3. It must be noted that the
simulation assumptions represent a multiple worst case scenario which is unlikely to for real network deployments. The
simulation results for power control set 1 and set 2 represent therefore the upper and lower boundary for the required
3GPP
Release 100T 59 3GPP TR 36.942 V10.3.0 (2012-06)
ACIR. It was demonstrated in [9] that the more aggressive power control set 1 does not improve the throughput in some
scenarios. Moreover, additional improvements by more advanced schedulers demonstrated in [10], [11], [12], have not
been taken into account for the simulations. Considering in addition UE implementation constraints, a UE ACLR of
33dB represents a balanced approach of system performance and UE complexity which is discussed in [13].
8.1.2 Requirements for E-UTRA – E-UTRA co-existence

UE ACLR can be obtained from downlink simulation results presented in section 7.1.1.4. With an E-UTRA UE ACLR
of 30dB the mean and cell edge user throughput degradation is less than 3% for both power control set 1 and power
control set 2 and not taking into account the additional improvements by more advanced scheduler mentioned
previously.
9 Deployment aspects
E-UTRA provides a significant number of features which can be exploited to support operation in diverse frequency
bands. The purpose of this section is to provide informative description how these features can be augment in a practical
deployment
9.1 UE power distribution

Three scenarios have been considered, with the simulation assumptions listed in Table 9.1. Note for scenario 3, the
propagation model is adopted from TR25.814 [4], where the penetration loss is included in the propagation model.
Table 9.1: simulation assumptions
Simulation CF ISD MCL Propagation model BS antenna pattern and gain

Cases (GHz) (meters) (dB) (dB)
15dBi
750   θ 2 
urban macro- 128.1+37.6 log(R), A(θ ) = − min 12  , Am 
  θ 3dB 
1 2.0 70
cell size in R in kilometers 
36.942
θ 3dB = 65 degrees, A m = 20 dB
15dBi
1732   θ 2 
128.1+37.6 log(R), A(θ ) = − min 12  , Am 
  θ 3dB 
2 2.0 70
macro-cell size R in kilometers 
in 25.814
θ 3dB = 65 degrees, A m = 20 dB
130 L[dB ] = 7 + 56 log10 (d [m]) 6 dBi for micro cell case with omni-
antennas
3 2.0 micro-cell size 53 (Outdoor to indoor,
in 25.814 penetration included) A(θ ) = 1
As for LTE UL power control, each LTE UE’s power is adjusted according to the following power control scheme:
3GPP
Release 100T 60 3GPP TR 36.942 V10.3.0 (2012-06)
   CL 
γ
 
Pt = Pmax × min 1, max  Rmin ,   
   CLx −ile   
where P max = 24dBm, Rmin = -54dB if UE minimum power is -30dBm (or R min = -64dB if UE minimum power is -
40dBm), CL x-ile and γ are set according to Table 9.2:
Table 9.2: Power control algorithm parameter
Parameter set Gamma CLx-ile
10MHz bandwidth 5 MHz bandwidth
Set 1 1 112 115
Set 2 0.8 129 133
9.1.1 Simulation results

Fig. 9.1 shows the UE transmit power distribution for different scenarios when different PC parameters are used.
Several observations are made for the as follows:
• For each scenario, the CDF curves for Pmin = -30dBm and Pmin = -40dBm almost overlap with each other
except for the power region where UEs transmit around minimum power.
• Generally speaking, UE transmit power for case 2 is greater than that for case 1 for the power region where
UEs transmit at high power. This is because case 2 has larger cell size and results in higher UE power for UEs
located close to cell border. This is also confirmed in Table 9.3 that presents UE mean and 95% CDF power
for different scenarios.
• For case 3 where a micro cell size is simulated, UE transmit power is not always lower than that for case 1 or 2.
The reason is that the pathloss model as shown in Table 9.1 includes penetration loss. As a result, the pathloss
is not necessarily smaller than that in case 1 or 2, where no penetration loss is considered. Since the PC scheme
is based on UE pathloss, the resulting UE power is not necessarily lower either. However, as shown in Table
9.3, the UE mean and 95% CDF power is significantly lower than their counterparts in case 1 or 2.
3GPP
Release 100T 61 3GPP TR 36.942 V10.3.0 (2012-06)
PC set 2
1
case 1, Pmin=-30dBm
0.9
case 2, P =-30dBm
min
0.8 case 3, Pmin=-30dBm

case 2, P =-40dBm
min
0.6
case 3, Pmin=-40dBm
CDF
0.5
0.4
0.3
0.2
0.1
0
-40 -30 -20 -10 0 10 20 30
LTE UE transmit power (dBm)
Figure 9.1: LTE UE transmit power CDF (PC set 2)
PC set 1
1
case 1, Pmin=-30dBm
0.9
case 2, Pmin=-30dBm

case 2, Pmin=-40dBm
0.6
case 3, Pmin=-40dBm
CDF
0.5
0.4
0.3
0.2
0.1
0
-40 -30 -20 -10 0 10 20 30
LTE UE transmit power (dBm)
Figure 9.2: LTE UE transmit power CDF (PC set 1)
3GPP
Release 100T 62 3GPP TR 36.942 V10.3.0 (2012-06)
Fig. 9.2 shows the UE transmit power distribution for different scenarios when different PC parameters are used.
Similar observations as mentioned for Fig. 9.1 can be made except for the fact that UEs transmit at a lower power than
when PC set 1 is used, which is expected.
Table 9.3: UE mean and 95% CDF power for PC set 1 and set 2
UE minimum power = -30dBm UE minimum power = -40dBm

Power control
Simulation Cases UE mean power UE 95% CDF UE mean power UE 95% CDF
parameters
(dBm) power (dBm) (dBm) power (dBm)
PC set 1 10.4 17.3 10.4 17.3
1
PC set 2 -2.1 4.2 -2.1 4.2
PC set 1 12.6 20.3 12.6 20.3
2
PC set 2 0.9 6.5 1 6.6
PC set 1 7.5 13 7.5 13
3
PC set 2 -4.1 0.8 -4.1 0.8
10 Multi-carrier BS requirements
The purpose of this section is to provide guidance how to interpret transmitter and receiver requirements for multi-
carrier BS.
10.1 Unwanted emission requirements for multi-carrier BS

10.1.1 General
In section 6.6 of TS 36.104 [19], unwanted emission requirements for single carrier or multi-carrier BS are specified.
This multi-carrier BS corresponds to the multi-carrier BS of the same channel bandwidth for E-UTRA. The following
two pragmatic scenarios can be considered.
- multi-carrier BS of different E-UTRA channel bandwidths
- multi-carrier BS of E-UTRA and UTRA
Different LTE channel bandwidths have different operating band unwanted emissions requirement. Only 5 MHz and
higher channel bandwidths have the same requirement. E-UTRA and UTRA have different mask requirements. In
section 10.1.2 and 10.1.3, unwanted emission requirements for BS with different channel bandwidths and in case of E-
UTRA and UTRA with following limited scenarios are introduced as a guideline.
- multi-carrier BS of different E-UTRA channel bandwidths covering only 5 MHz and higher channel bandwidths
(less than 5 MHz is FFS)
As an example, we can assume an operation such as the channel bandwidth of 10 MHz for the 1st carrier and
that of 5 MHz for the adjacent carrier as shown in Figure 10.1.
E-UTRA E-UTRA
10MHz 5MHz
f
Figure 10.1: multi-carrier BS of different E-UTRA channel bandwidths
- multi-carrier BS of different E-UTRA and UTRA covering only 5 MHz and higher E-UTRA channel bandwidths
(less than 5 MHz is FFS)
As an example, we can assume an operation such as E-UTRA with channel bandwidth of 5 MHz for 1st carrier
and UTRA for adjacent carrier as shown in Figure 10.2.
3GPP
Release 100T 63 3GPP TR 36.942 V10.3.0 (2012-06)
E-UTRA UTRA
5MHz 5MHz
f
Figure 10.2: multi-carrier BS of E-UTRA and UTRA
- only multi-carrier BS with contiguous carriers are considered.
- the guidelines below assumes that the power spectral density of the multiple carriers is the same.
All other combinations of multiple carriers are ffs.
10.1.2 Multi-carrier BS of different E-UTRA channel bandwidths

Among the unwanted emissions, the transmitter spurious emissions requirements in [19] should be applied irrespective
of channel bandwidth. Therefore, ACLR and Operating band unwanted emissions requirements for such a scenario of
different channel bandwidths should be specified as follows:
For multi-carrier E-UTRA BS of different channel bandwidths (≥5 MHz), the channel bandwidth of the outer most
carrier in the operating band should be considered. That is, the corresponding requirements for the channel bandwidth
of the outer most carrier should be applied at either side of the operating band as shown in Figure 10.3.
From a co-existence point of view, this guideline means that multi-carrier BS should not cause larger interference to
adjacent systems than single carrier BS. From the specification’s complexity point of view, this concept seems
reasonable.
E-UTRA E-UTRA
10MHz 5MHz
ACLR2 ACLR1 ACLR1 ACLR2
f
for UTRA for UTRA for UTRA for UTRA
ACLR1 for E-UTRA ACLR1 ACLR2

ACLR2 for E-UTRA
for EUTRA for EUTRA
-f_offsetmax Operating band Operating band f_offsetmax

unwanted emissions unwanted emissions
Figure 10.3: Unwanted emissions requirements for multi-carrier BS of different E-UTRA channel
bandwidths
10.1.3 Multi-carrier BS of E-UTRA and UTRA

Among the unwanted emissions, the transmitter spurious emissions requirements in [19] should be applied for E-UTRA
at frequencies within the specified frequency ranges, which are
- more than 10 MHz below the lowest frequency of the BS transmitter operating band if E-UTRA is the lowest
carrier or
- more than 10 MHz above the highest frequency of the BS transmitter operating band if E-UTRA is the highest
carrier.
Exceptions are the requirement in Table 6.6.4.3-2 and 6.6.4.3-3 of [19] that apply also closer than 10 MHz from
operating band.
For UTRA, the transmitter spurious emissions requirements in [20] should be applied at frequencies within the specified
frequency ranges, which are
- more than 12.5MHz below the first carrier used if UTRA is the lowest carrier or
- more than 12.5 MHz above the last carrier frequency used if UTRA is the highest carrier.
Exceptions are the requirement in Clause 6.6.3.5 and 6.6.3.8 of [20] that apply also closer than 12.5 MHz from the
outermost carrier frequency used.
3GPP
Release 100T 64 3GPP TR 36.942 V10.3.0 (2012-06)
Furthermore, Spectrum emission mask (SEM) applies to a UTRA BS transmitting on single RF carrier [20]. Thus SEM
should not be applied to multi-carrier BS of different RATs. Therefore, ACLR and Operating band unwanted emissions
requirements for such a scenario with E-UTRA and UTRA should be specified as follows:
For multi-carrier BS of E-UTRA (channel bandwidth(s) ≥5 MHz) and UTRA, the RAT being used at the edge of the
operating band should be considered. That is, the corresponding requirements for the RAT being used on the outer
most carrier should be applied at either side of the operating band as shown in Figure 10.4.
From a co-existence point of view, this guideline means that multi-carrier BS should not cause larger interference to
adjacent systems than single carrier BS. From the specification’s complexity point of view, this concept seems
reasonable.
E-UTRA UTRA
5MHz 5MHz
ACLR2 ACLR1
f
ACLR1 ACLR2
for UTRA for UTRA
ACLR2 ACLR1
for EUTRA for EUTRA
Operating band
-f_offsetmax
unwanted emissions
Figure 10.4: Unwanted emissions requirements for multi-carrier BS of E-UTRA and UTRA
10.2 Receiver requirements for multi-carrier BS

10.2.1 General
In a multi-carrier receiver, it is possible to set the processing bandwidth (i.e. used receiver BW) wider than a single E-
UTRA channel bandwidth. Both TX and RX requirements in [19] are specified at the BS antenna connector. From this
perspective there is a fundamental difference between a multi-carrier transmitter and a multi-carrier receiver. At the
antenna connector, the “lowest carrier frequency used” and the “highest carrier frequency used” can be recognized
via the emitted spectrum on the TX path. Therefore the same test set-up can be used for a single-carrier and a multi-
carrier transmitter. However, on the RX path, as long as a test is performed with a single wanted carrier, it is impossible
to identify at the antenna connector the lowest and the highest carrier frequency where simultaneously a certain
performance is achieved. A multi-carrier receiver should therefore be tested with a multi-carrier wanted signal.
With a multi-carrier wanted signal, the same principles applied to multi-carrier TX testing can also be applied to RX
testing. The manufacturer declares which frequency range and multi-carrier bandwidths that are supported. The lowest
and the highest supported bandwidth are tested as specified in section 4.7 of TS 36.141[21]. A wanted signal is applied
at the lower edge of the tested multi-carrier bandwidth. Another wanted signal is applied at the upper edge of the tested
multi-carrier bandwidth. It is not deemed necessary to apply wanted signals between the outer carriers, because usually
the worst performance is obtained at the outer channels. In the Reference sensitivity measurement only the two wanted
signals are applied. In the ACS, blocking and intermodulation measurements interferers are applied at frequencies
outside the tested multi-carrier bandwidth, with spacing as defined for each requirement in relation to the closest wanted
signal respectively. Following the TX testing approach, no requirements are specified for interferers between the
wanted channels.
Current specification allows the desensitization of the wanted signals in the presence of an interfering signal e.g., in the
ACS test. It is FFS whether this desensitization should be consider further for multi-carrier case.
Regarding Dynamic range and In-channel selectivity, a similar approach as for the Reference sensitivity level can be
adopted, i.e. two simultaneous wanted signals, one at the lowest assigned channel frequency and one at the highest
assigned channel frequency are chosen, together with their corresponding in-channel interfering signals. That is to say,
that the currently specified single carrier requirements should be simultaneously fulfilled at the lowest and highest
assigned E-UTRA channel frequency.
3GPP
Release 100T 65 3GPP TR 36.942 V10.3.0 (2012-06)
10.2.2 Test principles for a multi-carrier BS of equal or different E-UTRA

channel bandwidths
The following principles are proposed for receiver requirements in case of multi-carrier BS. Only 5 MHz and higher
channel bandwidths are considered (less than 5 MHz is FFS):
• In a receiver that can receive multiple contiguous carrier over a declared multi-carrier bandwidth, two
wanted carriers are tested simultaneously, at both edges of the multi-carrier bandwidth.
• There are no requirements for interfering signals between the wanted carriers.
• Only the highest and the lowest supported multi-carrier bandwidth are tested.
• The same set of interfering signals is used as in the equivalent single-carrier test. E.g. in a blocking
test there is only one blocker at a time, even though two simultaneous wanted signals are used.
• The test is repeated for the lower and upper wanted signals, with the interfering signals below the
lower and above the higher wanted signal respectively. The properties of the interferer(s) are chosen
according to the requirements of the closest wanted signal.
• For the receiver tests the desensitization for the wanted signals should be the same as for the single
carrier case.
11 Rationale for unwanted emission specifications

Unwanted emissions are divided into “Out-of-band emission” and “Spurious emissions” in 3GPP RF specifications.
This notation is in line with ITU-R recommendations such as SM.329 [22] and the Radio Regulations [23]. ITU defines:
Out-of-band emission = Emission on a frequency or frequencies immediately outside the necessary bandwidth which
results from the modulation process, but excluding spurious emissions.
Spurious emission = Emission on a frequency, or frequencies, which are outside the necessary bandwidth and the level
of which may be reduced without affecting the corresponding transmission of information. Spurious emissions include
harmonic emissions, parasitic emissions, intermodulation products and frequency conversion products but exclude out-
of-band emissions.
Unwanted emissions = Consist of spurious emissions and out-of-band emissions.
Some requirements in [19] may only apply in certain regions either as optional requirements or set by local and regional
regulation as mandatory requirements. It is normally not stated in the 3GPP specifications under what exact
circumstances the requirements apply, since this is defined by local or regional regulation.
All requirements that may be applied differently in different regions are listed in [19] Clause 4.3.
11.1 Out of band Emissions

Out of band emissions are unwanted emissions immediately outside the channel bandwidth resulting from the
modulation process and non-linearity in the transmitter but excluding spurious emissions. This out of band emission
requirement is specified both in terms of operating band unwanted emissions and adjacent channel power ratio (ACLR)
for the transmitter. ACLR is specified mainly as a measure of the capability of the transmitter to guarantee the
interfering signal below an acceptable level to the adjacent system to allow-coexistence. ACLR is also a regulatory
requirement in certain countries. Operating band unwanted emissions is specified mainly as a measure of the capability
of the transmitter to comply with certain regional regulatory requirements.
11.1.1 Operating band unwanted emission requirements for E-UTRA BS

(spectrum emission mask)
E-UTRA should have a operating band unwanted emissions (spectrum emissions mask, SEM) requirements defined,
based on the following prerequisites.
- SEM should be defined with a reference bandwidth of 100 kHz..
- The SEM limit should also be set to allow some variations due to varying power allocation between resource
blocks.
3GPP
Release 100T 66 3GPP TR 36.942 V10.3.0 (2012-06)
- FCC requirements [25] which apply mainly in Region 2 should be defined separately as an absolute limit and
may need a smaller reference bandwidth in some cases.
- In UTRA, the spectrum emissions mask is not only defined in the OOB domain, but also across the spurious
domain inside the operating band. This can also be the case for the E-UTRA mask, as long as the limits in the
spurious domain are consistent with recommended spurious limits in SM.329 [22]. The “unified” in-band OOB
+ spurious emissions for E-UTRA can be named “unwanted emissions” which is the agreed terminology [25]
that encompasses both OOB and spurious emissions.
- The SEM limit should apply for both single and multi-carrier BS.
- FCC requirements as defined in [25] apply for bands 2, 4, 5, 10, 12, 13, 14, 17, 35 and 36 as additional limits.
The Operating band unwanted emission limits are defined as a “mask” that stretches from 10 MHz below the lowest
frequency of the BS transmitter operating band up to 10 MHz above the highest frequency of the BS transmitter
operating band, as shown in Figure 11.1. Parts of the mask will be in the out-of-band domain (within +/-2.5 times the
necessary bandwidth of the carrier) and parts will be in the spurious domain..
The unwanted emission limit in the part of the operating band that falls in the spurious domain must be consistent with
SM.329 [22]. Based on the Category B spurious emission limits in [22] a level of -25 dBm in 100 kHz (-15 dBm in
1 MHz) is selected as the lower bound for the unwanted emission limits. This is consistent with the level used for
UTRA as spurious emission limit inside the operating band. Further details on the spurious emission limits and their
interpretation for UTRA (and E-UTRA) are given in TR 25.942 [3], clause 14.2.
For E-UTRA Bands 2, 4, 5, 10, 12, 13, 14, 17, 35, 36, an additional Unwanted emission limit is derived from FCC Title
47 [25] Parts 22, 24 and 27. The requirement stated in [25] is interpreted as -13 dBm in a measurement bandwidth
defined as 1% of the "-26 dB modulation bandwidth". For the E-UTRA channel bandwidths, the following additional
requirements are defined:
- 1.4 MHz channel bandwidth: -14 dBm in 10 kHz, which assumes that the "-26 dB modulation bandwidth" is <
1.26 MHz.
- 3 MHz channel bandwidth: -13 dBm in 30 kHz, which assumes that the "-26 dB modulation bandwidth" is <
3.0 MHz.
4.75 MHz.
10 MHz.
15.8 MHz.
20 MHz.
The additional limit outside the first MHz adjacent to the channel bandwidth, for all channel bandwidths, is -
13dBm/100kHz for E-UTRA Bands 5, 12, 13, 14, 17, and -13dBm/1MHz for E-UTRA Bands 2, 4, 10, 35 and 36.
3GPP
Release 100T 67 3GPP TR 36.942 V10.3.0 (2012-06)
Limits in
Carrier spurious domain
must be
consistent with
SM.329 [4]
10 MHz 10 MHz
Operating Band (BS transmit)
OOB domain
Operating Band Unwanted emissions limit
Figure 11.1 Defined frequency range for Operating band unwanted emissions with an example RF
carrier and related mask shape.
The requirements shall apply whatever the type of transmitter considered (single carrier or multi-carrier). It applies for
all transmission modes foreseen by the manufacturer's specification.
Emissions shall not exceed the maximum level specified in [19] for [any] BS maximum output power, where:
- ∆f is the separation between the channel edge frequency and the nominal -3dB point of the measuring filter
closest to the carrier frequency.
- f_offset is the separation between the channel edge frequency and the centre of the measuring filter.
- f_offset max is the offset to the frequency 10 MHz outside the operating band edge.
- ∆f max is equal to f_offset max minus half of the bandwidth of the measuring filter.
Minimum BS requirements for Category A and Category B are specified in [19].
11.1.2 ACLR requirements for E-UTRA BS

If there is to be both an ACLR-type requirement with carrier-wide reference bandwidth and a mask (SEM) with much
narrower reference bandwidth, the ACLR limit should be somewhat stricter than the integrated SEM. In this way, the
ACLR can capture the “average” behaviour over a carrier, while the SEM can take into account the variations in the
spectrum emissions resulting from variations in power allocations.
Since it is important to assess sharing properties both with adjacent UTRA systems and with E-UTRA carriers the
ACLR is defined with different bandwidths:
- ACLR/UTRA in a 1st and 2nd adjacent channel with 5 MHz and/or 1.6 MHz reference bandwidth depending on
paired or unpaired spectrum.
- ACLR/E-UTRA (reference bandwidth equal to E-UTRA channel bandwidth) in a 1st and 2nd adjacent channel.
- For carriers with channel bandwidth larger than 5 MHz positioned close to or adjacent to the band edge, the 1st or
2nd adjacent channel that define the ACLR/E-UTRA may fall partly or fully outside the point 10 MHz from the
band edge. If it is fully outside, it should not be defined. If it is partly outside it can still be defined, but may not
be limiting compared to the unwanted emission limits defined by SEM and spurious emissions.
- ACLR should apply for both single and multi-carrier BS.
ACLR measured in other reference bandwidths (smaller or larger) than the E-UTRA carrier or 5 MHz are indirectly
defined by the mask.
3GPP
Release 100T 68 3GPP TR 36.942 V10.3.0 (2012-06)
ACLR is defined for two cases as shown in Figure 11.2, i.e. for 1st and 2nd adjacent E-UTRA carriers of the same
bandwidth and for 1st and 2nd adjacent UTRA carriers. Separate limits are defined for each channel bandwidth. The
requirements can be stated with two tables, one for adjacent E-UTRA and one for adjacent UTRA.
Carrier
ACLR limits
defined for
adjacent
LTE carriers
ALCR limits
defined for Carrier
adjacent
UTRA carriers
10 MHz 10 MHz
Spurious Spurious
emissions limit emissions limit
st nd
Figure 11.2 The two defined ACLR measures, one for 1 and 2 adjacent E-UTRA carriers and one
st nd
for 1 and 2 adjacent UTRA carrier.
Minimum BS requirements for Category A and Category B are specified in [19]. BS ACLR requirements are captured
for E-UTRA operating in paired spectrum and in unpaired spectrum. For Category A, either the limits in [19] or the
absolute limit of -13dBm/MHz (Note 2) apply, whatever is less stringent. For Category B, the numbers are based on the
co-existence simulations outlined in this TR 36.942. Either the limits in [19] or the absolute limit of -15dBm/MHz
apply, whatever is less stringent.
NOTE: Whether the absolute limit is applicable to other base station classes is ffs.
NOTE2 Since the limits -13 dBm and -15 dBm are regulatory requirements taken from Category A and B spurious
emissions respectively, the test requirement shall also be -13dBm and -15 dBm respectively, i.e. the test
tolerance shall be zero when deriving the test limit.
The ACLR2 for the UTRA is set to be the same as ACLR1. It was revealed in [26] and [27] that the second adjacent
channel interference contributes only little to overall ACIR because ACLR/ACS in the second adjacent channel is
significantly higher than the UTRA UE ACS1.
It was pointed out in [28] that an E-UTRA BSs must not cause larger interference (in terms of absolute power) to the
co-existing UTRA system than the one allowed in the current 3GPP requirements, irrespective of its channel bandwidth.
For the deployment in Japan, additional spurious emission requirement to protect co-existing (domestic) wireless
systems may be required for certain bands (i.e. E-UTRA Band 1, 6, 9, and 11) in order to limit the ACI in 10, 15, and
20 MHz Channel BW options.
The measurement filter for the transmitted E-UTRA carrier and the adjacent E-UTRA carrier is a rectangular filter with
a bandwidth equal to the transmission bandwidth configuration N RB ∙ 180 kHz. For ACLR/UTRA, the power of the
adjacent carrier is measured using an RRC filter with roll-off factor α =0.22.
Adjacent Channel Leakage power Ratio (ACLR) is the ratio of the filtered mean power centered on the assigned
channel frequency to the filtered mean power centred on an adjacent channel frequency.
The requirements shall apply whatever the type of transmitter considered (single carrier or multi-carrier). It applies for
all transmission modes foreseen by the manufacturer's specification.
3GPP
Release 100T 69 3GPP TR 36.942 V10.3.0 (2012-06)
11.2 Spurious emissions

11.2.1 BS Spurious emissions
Spurious emissions are defined in ITU-R Radio Regulations [23] and SM.329 [22].
The UTRA core requirements for spurious emissions are specified for the BS in TS 25.104 [20].
References for the spurious emissions requirements are summarised in Table 11.1 for the BS. The tables give references
to RAN4 core specs, to where the term is defined and to some relevant regulatory references. These regulatory
references have either defined the limit value in 3GPP or they have used it as a basis for studies or recommendations.
Table 11.1 Summary of regulatory references for BS spurious emissions limits.
Spurious emissions RAN4 Definition Some relevant regulatory references

requirement TS
25.104 [20]
General 6.6.3.1 ITU-R ITU-R M.1580 (Annex 1.4) [29]: Band I limits included.
SM.329 [22] ITU-R SM.329[22]: 1.4 Necessary bandwidth
4.1 Reference bandwidths
4.2 Category A limits
4.3 Category B limits
Annex 7. Reference BW (Cat. B)
ITU-R M.2039 [30]: Limits included by reference.
ETSI EN 301 908-3 [31]: Category B limits included.
Co-existence with other 6.6.3.2 to Developed ITU-R M.1580 (Annex 1.4) [29]: Band I limits included.
bands 6.6.3.7 and defined ITU-R. M.2039 [30]: Limits included by reference.
in 3GPP. ETSI EN 301 908-3 [31]: Limits to protect GSM900 and
GSM1800 in the same area included.
11.2.2 General spurious emissions requirements for E-UTRA BS

The definition of “Operating band unwanted emissions” for E-UTRA covers not only the OOB domain, but also the
spurious domain inside the operating band, including the 10 MHz of spectrum immediately above and below the
operating band. For that reason, there is no need to define spurious emission limits inside the operating band as shown
in Figure 11.3. The implication is that the rule that spurious emissions start at a point separated from the carrier centre
by 250% of the necessary bandwidth is not applied. Note however that since parts of the Operating band unwanted
emission limits will fall inside the spurious domain, they are bound by the same regulatory limits that define spurious
emissions. The operating band unwanted emission limits are further discussed in Clause 11.1.1.
Since the spurious emission limits defined here does not cover the frequency range of the spurious domain inside the
operating band, they should be named “Spurious emissions outside the operating band”, in order to distinguish them
from the definition of spurious emissions in the spurious domain in ITU-R SM.329 [22].
10 MHz 10 MHz
Spurious Operating band Unwanted Spurious

emissions limit emissions limit emissions limit
Figure 11.3 Defined frequency ranges for spurious emissions and operating band unwanted
emissions
Spurious emission limits as defined in ITU-R SM.329[22] are divided into several Categories, where Category A and B
are applied for 3GPP as regional requirements. The Category A and Category B spurious emission limits in Tables 11.2
and 11.3 are in line with ITU-R SM.329[22]. They would apply outside of the region where the limits for “Operating
3GPP
Release 100T 70 3GPP TR 36.942 V10.3.0 (2012-06)
band unwanted emissions” are defined (operating band plus 10 MHz on each side). Further details on the spurious
emission limits and their interpretation for UTRA (and E-UTRA) are given in TR 25.942 [3], clause 14.2.
11.2.3 Specification of BS Spurious emissions outside the operating band

The spurious emission limits (except the protection of PHS and Public Safety operations) apply in frequency ranges that
are more than 10 MHz below the lowest BS transmitter frequency of the operating band and more than 10 MHz above
the highest BS transmitter frequency of the operating band. The requirements shall apply whatever the type of
transmitter considered (single carrier or multi-carrier). It applies for all transmission modes foreseen by the
manufacturer's specification.
Table 11.2: BS Spurious emission limits outside the operating band, Category A
Band Maximum level Measurement Note

Bandwidth
9kHz - 150kHz 1 kHz Note 1
150kHz - 30MHz 10 kHz Note 1
-13 dBm
30MHz - 1GHz 100 kHz Note 1
1GHz - 12.75 GHz 1 MHz Note 2
NOTE 1: Bandwidth as in ITU-R SM.329 [22] , s4.1
NOTE 2: Bandwidth as in ITU-R SM.329 [22] , s4.1. Upper frequency as in ITU-R SM.329 [22] , s2.5
table 1
Table 11.3: BS Spurious emissions limits outside the operating band, Category B
Band Maximum Measurement Note

Level Bandwidth
9 kHz ↔ 150 kHz -36 dBm 1 kHz Note 1
150 kHz ↔ 30 MHz -36 dBm 10 kHz Note 1
30 MHz ↔ 1 GHz -36 dBm 100 kHz Note 1
1 GHz ↔ 12.75 GHz -30 dBm 1 MHz Note 2
NOTE 1: Bandwidth as in ITU-R SM.329 [22] , s4.1
NOTE 2: Bandwidth as in ITU-R SM.329 [22] , s4.1. Upper frequency as in ITU-R SM.329 [22] ,
s2.5 table 1
Minimum BS spurious emissions requirements are specified in [19] including Category A, Category B, protection of the
BS receiver of own or different BS, co-existence with other systems in the same geographical area, limits for BS in
geographic coverage area of PHS, limits for protection of public safety operations and co-location with other base
stations.
BS Spurious emissions limits for BS co-located with another BS in [19] do not apply for the 10 MHz frequency range
immediately outside the BS transmit frequency range of an operating band. This is also the case when the transmit
frequency range is adjacent to the Band for the co-location requirement. The current state-of-the-art technology does not
allow a single generic solution for co-location with other system on adjacent frequencies for 30dB BS-BS minimum
coupling loss. However, there are certain site-engineering solutions that can be used. These techniques are addressed in
TR 25.942 [3].
11.2.4 Additional spurious emissions requirements

These requirements may be applied for the protection of system operating in frequency ranges other than the E-UTRA
BS operating band. The limits may apply as an optional protection of such systems that are deployed in the same
geographical area as the E-UTRA BS, or they may be set by local or regional regulation as a mandatory requirement for
an E-UTRA operating band. It is in some cases not stated in [19] whether a requirement is mandatory or under what
exact circumstances that a limit applies, since this is set by local or regional regulation. An overview of regional
requirements is given in [19] Clause 4.3.
3GPP
Release 100T 71 3GPP TR 36.942 V10.3.0 (2012-06)
12 LTE-Advanced co-existence
12.1 Methodology and simulation assumptions for co-existence

simulations
This section describes the method of used for LTE-Advanced co-existence study to focus the modified methodology
and assumptions.
12.1.1 Simulation scenarios

Table 12.1 and Table 12.2 show the simulation scenario for LTE-Advanced coexistence and BS/UE model for LTE-A
coexistence evaluation respectively.
Table 12.1: Simulation scenarios for LTE-Advanced coexistence
Scenari Aggressor Victim Simulation Environme Cell

ISD Priority
o# system system frequency nt Range
DL: 40 MHz,
1 UL: 40 MHz 10 MHz LTE 2000 MHz Urban Area 750 m 500 m High
LTE-A
DL: 40 MHz, DL: 40 MHz,
2 UL: 40 MHz UL: 40 MHz 2000 MHz Urban Area 750 m 500 m High
LTE-A LTE-A
DL: 40 MHz,
5 MHz UTRA
3 UL: 40 MHz 2000 MHz Urban Area 750 m 500 m High
FDD
LTE-A
DL: 40 MHz,
1.6MHz UTRA
4 UL: 40 MHz 2000 MHz Urban Area 750 m 500 m High
TDD
LTE-A
Table 12.2 BS and UE model for LTE-A coexistence
Parameters Assumptions
Deployment scenario Macro cell, Urban area, Uncoordinated deployment
43 dBm for UTRA FDD,

34 dBm for UTRA TDD,
Total BS transmit power
46 dBm for 10 MHz LTE,
49 dBm for 40 MHz LTE-A
BS noise figure 5 dB
21 dBm for 5MHz UTRA,
UE Tx power 24dBm for 1.6MHz UTRA
23 dBm for 10 MHz LTE/ 40MHz LTE-A
UE noise figure 9 dB
12.1.2 Number of UEs per sub-frame

For downlink, the number of UEs per sub-frame would not affect the simulation results, because the total transmission
power for the system would be constant. The number of UEs per sub-frame for downlink is presented in Table 12.3.
Table 12.3 Number of UEs per sub-frame for downlink
System Number of UEs per Number of RBs per UE

subframe
LTE 1 UEs 50 RBs
LTE-Advanced 1 UEs 200 RBs
3GPP
Release 100T 72 3GPP TR 36.942 V10.3.0 (2012-06)
For uplink, the number of UEs per sub-frame might affect the simulation results, because the total transmission power
for the system would depend on the number of UEs per sub-frame. Since the number of resource blocks for one UE
would be typically 8~16 in the actual UL scheduler, it is proposed that the number of UEs per sub-frame is calculated as
follows:
(Number of UEs per sub-frame) = round down ((Total number of RBs for the system) / 16)
The number of UEs per sub-frame for uplink is presented in Table 12.4.
Table 12.4 Number of UEs per sub-frame for uplink
Number of UEs per

System Number of RBs per UE
subframe
LTE 3 UEs 16 RBs (Total: 48 RBs)
LTE-Advanced 12 UEs 16 RBs (Total: 192 RBs)
Note: The resource block size should be 180 kHz instead of 375 kHz.
12.1.3 ACIR model

The ACIR is defined as the ratio of the total power transmitted from an aggressor transmitter (BS or UE) to the total
interference power affecting a victim receiver, resulting from both transmitter and receiver imperfections. Thus, ACIR
= P aggressor – P victim (all in dB), where P aggressor is the transmit power of an aggressor and P victim is the interference power
at the victim receiver.
12.1.3.1 Uplink ACIR model

For uplink, it is assumed that the ACIR is dominated by the UE ACLR. As shown in Figure 12.1 and Table 12.5, the
bandwidth for each ACIR value was assumed to be the same as the transmission bandwidth of LTE-A UE. Outside
ACIR1/2 regions, ACIR3 was used for all the regions. Those models are modified model, in which the ACIR3 is
smaller than ACIR2 based on the actual spectrum shape.
Aggressor Unwanted emissions
ACIR1 ACIR3
ACIR2 ACIR3
frequency
Figure 12.1 Uplink ACIR models
Table 12.5 ACIR models for LTE-A coexistence

ACIR value (Ref. LTE model)
ACIR1 30 + X 30 + X
ACIR2 43 + X 43 + X
ACIR3 50 + X 43 + X
The bandwidth of victim UEs are same that of aggressor UEs in Scenario #1 and #2 (victim in LTE or LTE-Advanced).
ACIR value could be calculated from uplink ACIR model shown in table 12.6.
3GPP
Release 100T 73 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.6 ACIR value for Scenario#1 and #2

Frequency offset between aggressor
(16 RBs) and victim (16RBs)
ACIR value
0 RBs 30 + X
16 RBs 43 + X
≥32RBs 50 + X
For Scenario #3 (3.84 MHz UTRA victim), the bandwidth of victim UEs are larger than that of aggressor UEs (2.88
MHz = 180 kHz x 16 RBs). As shown in figure 12.2, 12.3 and 12.4, victim UE suffer from the interference composed
by two ACIR regions from an aggressor UE in asymmetrical bandwidths case. Based on the method described in
5.1.1.4.2, ACIR value from a UE could be calculated as shown in table 12.7.
Figure 12.2 Uplink ACIR models from aggressor UE1 for LTE-A vs. UTRA case
3GPP
Release 100T 74 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.7 ACIR value for Scenario#3

ACIR value
0 RBs 30 + X
16 RBs 43 + X
≥32RBs 49 + X
For Scenario #4 (1.28 MHz UTRA victim), the bandwidth of victim UEs are smaller than that of aggressor UEs (2.88
MHz = 180 kHz x 16 RBs). As shown in figure 12.5, 12.6 and 12.7, victim UE suffer from the interference one ACIR
region from an aggressor UE. Based on the method described in 5.1.1.4.2, ACIR value from a UE could be calculated
as shown in table 12.8.
3GPP
Release 100T 75 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.8 ACIR value for Scenario#4

ACIR value
0 RBs 33.5 + X
16 RBs 46.5+X
≥32RBs 53.5+X
12.1.3.2 Downlink ACIR model

For downlink a common ACIR obtained from the LTE-A BS ACLR and the victim UE ACS requirements can be used
for all frequency resource blocks independent of their position in the aggressor channel. The ACLR of the LTE-A BS is
much bigger than the ACS of the victim ACS and therefore has negligible impact on ACIR performance. In other words,
the BS ACLR can be assumed as infinite and ACIR is only a function of the victim UE ACS, which can be
mathematically described as ACIR = Average + X (in dB), where X is an offset relative to the “Average”. For
Scenarios 1 and 3, the “Average” is determined from the UE ACS requirements (ACS1, ACS2 and ACS3) according to
the respective specifications by the following relation (all parameters in dB):
1 1  5 5 30 
= *  0.1* ACS 1 + 0.1* ACS 2 + 0.1* ACS 3 
40  10 
0.1* Average
10 10 10
For Scenario 2, the “Average” is based on an assumption for the 40 MHz LTE-A ACS.
For Scenarios 4, the “Average” is determined from the UE ACS requirements (ACS1, ACS2 and ACS3) according to
the respective specifications by the following relation (all parameters in dB):
1 1  1.6 1.6 36.8 

= *  0.1* ACS 1 + 0.1* ACS 2 + 0.1* ACS 3 
10 0.1* Average
40  10 10 10 
As shown in figure 12.8, figure 12.9, figure 12.10 and table 12.9, the ACIR offset calculated from the victim UE
performance in TR25.101 for UTRA and TR36.101 for LTE of UE ACS.
Figure 12.8 Downlink ACIR model for Scenario #1
3GPP
Release 100T 76 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.9 ACS and ACIR value for LTE-A coexistence

Victim system
10 MHz LTE 40 MHz LTE-A 5 MHz UTRA 1.6 MHz UTRA
ACS1 [dB] 33.0 ― 33.0 33.0
ACS2 [dB] 34.3 ― 43.0 43.0
ACS3 [dB] 46.3 ― 55.0 55.0
ACIR [dB] 39 + X 30 + X 42 + X 46 + X
12.1.4 Uplink power control

For downlink, no power control scheme is applied and the transmission power per RB should be constant.
For LTE coexistence study, the fractional power control was used for the initial uplink coexistence simulations. It is
noted that the parameter CLx-ile in the table below is the same for both 40 MHz and 10 MHz systems because it is
assumed that each UE is assigned 16 RBs in either system.
Table 12.10 Power control algorithm parameter of LTE coexistence
3GPP
Release 100T 77 3GPP TR 36.942 V10.3.0 (2012-06)
CL x-ile
Parameter Set Gamma
40MHz 10MHz
Set 1 1 112- ∆ 112- ∆
Set 2 0.8 129- ∆ 129- ∆
Note: ∆ = 21log10 ( f c / 2.0) , adjustment parameter related to different carrier
frequency point. For fc=2GHz, ∆ =0dB.
In RAN1 TS36.213, The setting of the UE Transmit power PPUSCH for the physical uplink shared channel (PUSCH)
transmission in subframe i is defined by:
PPUSCH (i ) = min (PCMAX ,10 log10 ( M PUSCH (i )) + PO_PUSCH ( j ) + α ( j ) ⋅ PL + ∆ TF (i ) + f (i ) )
Note 1: ∆ TF (i ) = 0 dB, f (i ) = 0 dB, and PL in the above equation is equivalent to CL defined in TR 36.942
Section 5.1.1.6.
Note 2: PO_PUSCH ( j ) should be derived from CL x-ile so that the actual transmission power should be the same as
the one for PC Set 1/2. Following this principle, PO_PUSCH ( j ) can be obtained and included in the table
below, assuming each UE occupies 16RBs (as shown in Section 12.1.2):
Table 12.11 PO_PUSCH ( j ) value (in dBm)
P 0_PUSCH (j) [dBm]

Parameter Set Alpha
40 MHz (LTE-A) 10 MHz (LTE)
Set 1 1 -101 -101
Set 2 0.8 -92.2 -92.2
Note that when calculating PO_PUSCH ( j ) , it is assumed that PCMAX is equal to P PowerClass. In other words, no MPR, A-
MPR or power tolerances are considered for simplicity.
12.2 Results
12.2.1 Radio reception and transmission
12.2.1.1 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 10 MHz E-UTRA

victim
Aggressor system: 40 MHz Advanced E-UTRA
Cell Range 500 m
Simulation results for average E-UTRA downlink cell throughput loss are presented in table 12.12 and figure 12.11.
Simulation results for 5% CDF E-UTRA downlink user throughput loss are presented in table 12.13 and figure 12.12.
3GPP
Release 100T 78 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.12 average E-UTRA downlink throughput loss
NTT
ACIR Qual Hua Alcatel- CMC Sam Moto
LGE DOCO CATT CATR ZTE
offse ave comm wei Lucent C sung rola
(R4- MO (R4- (R4- (R4-
t rag (R4- (R4- (R4- (R4- (R4- (R4-
101144 (R4- 10117 10158 10170
X e 10214 10135 101114 10127 10184 10207
) 101350 3) 9) 0)
[dB] 7) 3) ) 8) 2) 6)
)
-25 17.6 15.3 20.2 17.3
-20 9.9 8.1 11.2 9.99 11.17 9.2 10.26 8.81 10.7
-15 5.1 3.8 5.8 4.94 5.8 5.79 4.4 5.38 4.79 5.3
-10 2.6 2.8 1.6 2.8 2.18 2.7 2.82 2.1 2.57 2.35 2.4 4.2
-5 1.1 1.3 0.6 1.2 0.85 1.1 1.22 0.8 1.14 1.06 1 1.8
0 0.4 0.56 0.2 0.5 0.29 0.4 0.53 0.4 0.46 0.44 0.4 0.7
5 0.2 0.24 0.1 0.2 0.1 0.2 0.19 0.1 0.17 0.17 0.1 0.25
10 0.1 0.09 0.1 0.032 0.1 0.09 0.05 0.06 0.1 0.07
15 0.0 0.0 0.01 0 0.02 0
20.0 average
Qualcomm
(R4-102147)
LGE
15.0 (R4-101144)
NTT DOCOMO
(R4-101350)
Huawei
Loss [%]
(R4-101353)
10.0 Alcatel-Lucent
(R4-101114)
CATT
(R4-101173)
CMCC
5.0 (R4-101278)
CATR
(R4-101589)
ZTE
(R4-101700)
0.0 Samsung
-20 -10 0 10 20 (R4-101842)
Motorola
Offset value X [dB] (R4-102076)
Figure 12.11 average E-UTRA downlink throughput loss
Table 12.13 5%-ile E-UTRA downlink throughput loss
Qual NTT
ACIR Hua Alcatel- CMC Sam Moto
com LGE DOCO CATT CATR ZTE
Offse ave wei Lucent C sung rola
m (R4- MO (R4- (R4- (R4-
t r (R4- (R4- (R4- (R4- (R4-
(R4- 101144 (R4- 10117 10158 10170
X age 10135 101114 10127 10184 10207
10214 ) 101350 3) 9) 0)
[dB] 3) ) 8) 2) 6)
7) )
-25 83.0 70.8 100.0 78.3
-20 47.8 37.3 47.1 100 52.29 40.4 44.74 21.68 39.1
-15 22.0 16.2 23.4 46.54 18.2 24.17 18.7 23.52 8.05 18.8
3GPP
Release 100T 79 3GPP TR 36.942 V10.3.0 (2012-06)
-10 8.9 11.5 6.2 10.6 11.65 7.7 10.7 8.2 10.93 2.69 7.9 10.3
-5 3.4 4.6 2.1 5.0 2.81 1.4 5.33 3.2 4.7 0.87 3.2 4.5
0 1.3 1.8 0.6 1.2 0.78 0.8 2.23 1.3 1.8 0.28 1.6 1.5
5 0.5 0.77 0.2 0.6 0.27 0.7 0.84 0.4 0.53 0.09 0 0.56
10 0.2 0.39 0.2 0.087 0.6 0.38 0.2 0.03 0 0.21
15 0.0 0 0.029 0.2 0.01 0
50.0 average
Qualcomm
(R4-102147)
40.0 LGE
(R4-101144)
NTT DOCOMO
(R4-101350)
30.0 Huawei
Loss [%]
(R4-101353)
Alcatel-Lucent
(R4-101114)
20.0 CATT
(R4-101173)
CMCC
(R4-101278)
10.0 CATR
(R4-101589)
ZTE
(R4-101700)
0.0 Samsung
(R4-101842)
-20 -10 0 10 20 Motorola
Figure 12.12 5%-ile E-UTRA downlink throughput loss
12.2.1.2 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 10 MHz E-UTRA victim
Cell Range 500 m
Simulation results for average E-UTRA uplink cell throughput loss are presented in table 12.14 and figure 12.13 for
TPC set 1 and table 12.15 and figure 12.14 for TPC set 2 respectively. Simulation results for 5% CDF E-UTRA uplink
user throughput loss are presented in table 12.16 and figure 12.15 for TPC set 1 and table 12.17 and figure 12.16 for
TPC set 2 respectively.
3GPP
Release 100T 80 3GPP TR 36.942 V10.3.0 (2012-06)
Table 12.14 average E-UTRA uplink throughput loss (TPC set 1)
Qual
NTT NOKI Hua Alcatel- CM Sam Moto
Offset com LGE CATT ZTE
ave DOCOM A wei Lucent CC sung rola
value m (R4- (R4- (R4-
rag O (R4- (R4- (R4- (R4- (R4- (R4-
X (R4- 10114 10117 10170
e (R4- 10138 102054 101114 101 10184 10207
[dB] 1013 4) 3) 0)
101341) 9) ) ) 278) 2) 6)
07)
-20 27.9 35.90 19.84
-15 22.5 34.7 25.6 21.73 21.8 18.7 11.09 23.6
-10 12.5 13.16 18.6 13.2 20.41 11.53 10.6 10.29 9 5.46 10.7 14.8
-5 5.7 5.71 8.8 6.1 10.33 5.29 4.7 4.65 3.8 2.27 4.4 6.3
0 2.4 2.60 3.8 2.6 4.7 2.11 2.3 1.98 1.6 0.81 1.7 2.4
5 0.9 1.18 1.5 1.0 1.97 0.75 0.9 0.77 0.5 0.27 0.6 0.95
10 0.4 0.50 0.6 0.4 0.78 0.25 0.4 0.3 0.2 0.09 0.2 0.28
15 0.1 0.2 0.0 0.08 0.1 0.1 0.1 0.03 0.1
20 0.0 0.04
30.0
average
Qualcomm
25.0 (R4-101307)
LGE
(R4-101144)
NTT DOCOMO
20.0 (R4-101341)
NOKIA
Loss [%]
(R4-101389)
15.0 Huaw ei
(R4-102054)
Alcatel-Lucent
(R4-101114)
10.0 CATT
(R4-101173)
CMCC
5.0 (R4-101278)
ZTE
(R4-101700)
Samsung
0.0 (R4-101842)
-20 -10 0 10 20 Motorola
Figure 12.13 average E-UTRA uplink throughput loss (TPC set 1)
Table 12.15 average E-UTRA uplink throughput loss (TPC set 2)
Qual
NTT NOKI Hua Alcatel- CM Sam Moto
Offset com LGE CATT ZTE
ave DOCOM A wei Lucent CC sung rola
value m (R4- (R4- (R4-
r O (R4- (R4- (R4- (R4- (R4- (R4-
X (R4- 10114 10178 10170
age (R4- 10138 102054 101114 101 10184 10207
[dB] 10130 4) 0) 0)
101341) 9) ) ) 278) 2) 6)
7)
-20 19.0 28.35 9.64
-15 15.3 22.6 17.5 15.35 15.7 12.4 5.25 18.2
-10 7.5 7.8 10.9 8.3 10.6 7.16 7.4 6.2 5.4 2.22 8.4 8.49
-5 3.2 3.34 4.7 3.6 4.72 2.90 3.2 2.62 2.2 0.79 3.5 3.34
0 1.2 1.31 1.9 1.4 1.95 1.05 1.3 1.04 0.8 0.26 1.4 1.23
5 0.5 0.61 0.7 0.5 0.76 0.35 0.5 0.39 0.4 0.08 0.5 0.42
10 0.2 0.29 0.3 0.2 0.28 0.11 0.2 0.14 0.2 0.03 0.2 0.13
3GPP
Release 100T 81 3GPP TR 36.942 V10.3.0 (2012-06)
15 0.1 0.1 0.0 0.04 0.1 0.06 0.1 0.01 0.1

20 0.0 0.02
30.0 average
Qualcomm
25.0 (R4-101307)
LGE
(R4-101144)
NTT DOCOMO
20.0 (R4-101341)
NOKIA
Loss [%]
(R4-101389)
15.0 Huawei
(R4-102054)
Alcatel-Lucent
(R4-101114)
10.0 CATT
(R4-101780)
CMCC
5.0 (R4-101278)
ZTE
(R4-101700)
Samsung
0.0
(R4-101842)
-20 -10 0 10 20 Motorola
Figure 12.14 average E-UTRA uplink throughput loss (TPC set 2)
Table 12.16 5%-ile E-UTRA uplink throughput loss (TPC set 1)
Qual
NTT Hua Alcatel CMC Samsu
com LGE CATT ZTE
Offset ave DOCOM wei -Lucent C ng Motorola
m (R4- (R4- (R4-
value rag O (R4- (R4- (R4- (R4- (R4-
(R4- 10114 101173 101700
X [dB] e (R4- 10205 101114 10127 101842 102076)
1013 4) ) )
101341) 4) ) 8) )
07)
-20 53.2 51.49 54.93
-15 39.4 90.2 42.4 25.83 36.7 34.2 17.51 29.1
-10 14.5 17.22 29.8 17.1 8.25 14.6 11.74 12.9 5.55 11.5 16.6
-5 5.6 6.42 11 6.5 2.32 7.9 5.17 4.6 1.76 4.2 5.8
0 1.9 2.24 4 2.9 0.57 2.6 1.99 1.5 0.56 1.8 1.3
5 0.7 1.09 1.5 1.3 0.19 0.6 0.64 0.5 0.18 0.6 0.62
10 0.2 0.56 0.3 0.4 0.06 0.1 0.14 0.2 0.06 0 0.14
15 0.0 0 0.0 0.02 0 0.06 0.2 0.02 0
20 0.0 0.02
3GPP
Release 100T 82 3GPP TR 36.942 V10.3.0 (2012-06)
50.0
average
Qualcomm
40.0 (R4-101307)
LGE
(R4-101144)
NTT DOCOMO
30.0 (R4-101341)
Loss [%]
Huawei
(R4-102054)
Alcatel-Lucent
20.0 (R4-101114)
CATT
(R4-101173)
CMCC
10.0
(R4-101278)
ZTE
(R4-101700)
0.0 Samsung
(R4-101842)
-20 -10 0 10 20 Motorola
Offset value X dB] (R4-102076)
Figure 12.15 5%-ile E-UTRA uplink throughput loss (TPC set 1)
Table 12.17 5%-ile E-UTRA uplink throughput loss (TPC set 2)
Qual
NTT Hua Alcatel- Moto
Offset com LGE CATT CMCC ZTE Sam
ave DOCOM wei Lucent rola
value m (R4- (R4- (R4- (R4- sung
rag O (R4- (R4- (R4-
X (R4- 10114 101780 101278 101700 (R4-
e (R4- 102054 101114 102076
[dB] 1013 4) ) ) ) 101842)
101341) ) ) )
07)
-20 32.2 41.14 23.27
-15 26.6 52.8 31.7 17.91 30.8 23.9 7.37 21.6
-10 11.6 15.7 20.7 13.0 6.41 14.6 10.13 9.5 2.33 8.8 14.39
-5 4.2 5.5 7.6 5.2 1.68 5.4 3.94 3.2 0.74 4 4.75
0 1.3 1.81 2.7 1.8 0.51 1.3 0.97 0.9 0.23 1.6 1.05
5 0.5 0.8 0.8 0.7 0.17 0.3 0.34 0.3 0.07 0.8 0.3
10 0.1 0.13 0.1 0.2 0.05 0 0.06 0.1 0.02 0.1 0.09
15 0.0 0 0 0.02 0 0.01 0.1 0.01 0
20 0.0 0
3GPP
Release 100T 83 3GPP TR 36.942 V10.3.0 (2012-06)
50.0
average
Qualcomm
40.0 (R4-101307)
LGE
(R4-101144)
NTT DOCOMO
30.0 (R4-101341)
Loss [%]
Huawei
(R4-102054)
Alcatel-Lucent
20.0 (R4-101114)
CATT
(R4-101780)
CMCC
10.0 (R4-101278)
ZTE
(R4-101700)
Samsung
0.0
(R4-101842)
-20 -10 0 10 20 Motorola
Figure 12.16 5%-ile E-UTRA uplink throughput loss (TPC set 2)
12.2.1.3 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 40 MHz Advanced E-

UTRA victim
Victim system: 40 MHz Advanced E-UTRA
Cell Range 500 m
Simulation results for average Advanced E-UTRA downlink cell throughput loss are presented in table 12.18 and figure
12.17. Simulation results for 5% CDF Advanced E-UTRA downlink user throughput loss are presented in table 12.19
and figure 12.18.
Table 12.18 average Advanced E-UTRA downlink throughput loss
Qual
NTT Hua Alcatel- Moto
ACIR com LGE CMCC CATR ZTE Sam
ave DOCOM wei Lucent rola
offset m (R4- (R4- (R4- (R4- sung
r O (R4- (R4- (R4-
X (R4- 10114 101279 101589 101701 (R4-
age (R4- 101354 101114 102077
[dB] 10144 5) ) ) ) 101843)
101350) ) ) )
6)
-20 20.8 21.9 14.61 25.81
-15 12.1 10.5 12.4 7.66 12.8 11.9 17.53 12.2
-10 6.4 6.4 5.2 6.5 3.62 6.6 6.1 6.18 10.93 6.1 5.92
-5 3.1 3.2 2.3 3.2 1.51 3.2 2.7 3.04 6.43 2.8 2.69
0 1.4 1.47 0.9 1.4 0.55 1.4 1.1 1.37 3.66 1.2 1.03
3GPP
Release 100T 84 3GPP TR 36.942 V10.3.0 (2012-06)
5 0.7 0.48 0.3 0.6 0.18 1.3 0.4 0.55 2.03 0.5 0.54
10 0.3 0.16 0.1 0.2 0.05 0.2 0.2 0.21 1.10 0.2 0.14
15 0.1 0 0.1 0.006 0.1 0 0.07 0.60 0.1
20 0.0 0.0
20.0 average
Qualcomm
(R4-101446)
LGE
15.0 (R4-101145)
NTT DOCOMO
(R4-101350)
Loss [%]
Huawei
(R4-101354)
10.0
Alcatel-Lucent
(R4-101114)
CMCC
(R4-101279)
5.0 CATR
(R4-101589)
ZTE
(R4-101701)
Samsung
0.0
(R4-101843)
-20 -10 0 10 20 Motorola
(R4-102077)
Offset value X [dB]
Figure 12.17 average Advanced E-UTRA downlink throughput loss
Table 12.19 5%-ile Advanced E-UTRA downlink throughput loss
NTT
Qualc Alcatel- Sam Moto
ACIR LGE DOCO CATR ZTE
omm Huawei Lucent CMCC sung rola
offse aver (R4- MO (R4- (R4-
(R4- (R4- (R4- (R4- (R4- (R4-
tX age 10114 (R4- 10158 10170
10144 101354) 101114 101279) 101843 102077
[dB] 5) 101350 9) 1)
6) ) ) )
)
-25 100.0 100.0 100.0
-20 93.7 100.0 100 81.15
-15 55.6 49.2 54.4 83.17 48.7 52.6 57.67 43.4
-10 25.8 27.9 23 28.8 26.3 21.2 25.7 26.82 30.11 21.9 26.71
-5 11.1 12.9 9.2 14.1 8.71 8.9 11.4 12.86 12.00 9.4 11.32
0 4.3 5.8 3.2 6.0 2.4 2.3 4.3 5.43 4.13 4.7 4.28
5 1.6 2.2 0.9 2.40 1.11 1.7 1.4 1.91 1.35 1.6 1.76
10 0.5 0.68 0.4 0.75 0.32 0.8 0.4 0.74 0.43 0 0.72
15 0.2 0.1 0.15 0.19 0.6 0.1 0.23 0.14 0
20 0.2 0.15
3GPP
Release 100T 85 3GPP TR 36.942 V10.3.0 (2012-06)
50.0
average
Qualcomm
40.0 (R4-101446)
LGE
(R4-101145)
NTT DOCOMO
30.0 (R4-101350)
Loss [%]
Huawei
(R4-101354)
Alcatel-Lucent
20.0 (R4-101114)
CMCC
(R4-101279)
10.0 CATR
(R4-101589)
ZTE
(R4-101701)
0.0 Samsung
(R4-101843)
-20 -10 0 10 20
Motorola
Figure 12.18 5%-ile Advanced E-UTRA downlink throughput loss
12.2.1.4 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 40 MHz Advanced E-

UTRA victim
Victim system: 40 MHz Advanced E-UTRA
Cell Range 500 m
Simulation results for average Advanced E-UTRA uplink cell throughput loss are presented in table 12.20 and figure
12.19 for TPC set 1 and table 12.21 and figure 12.20 for TPC set 2 respectively. Simulation results for 5% CDF
Advanced E-UTRA uplink user throughput loss are presented in table 12.22 and figure 12.21 for TPC set 1 and table
12.23 and figure 12.22 for TPC set 2 respectively.
Table 12.20 average Advanced E-UTRA uplink throughput loss (TPC set 1)
NTT
Offse Hua Alcatel- Sam Moto
Qual LGE DOCO NOKIA CATT CMCC ZTE
t wei Lucent sung rola
aver comm (R4- MO (R4- (R4- (R4- (R4-
value (R4- (R4- (R4- (R4-
age (R4- 1011 (R4- 101389 10117 101965 101701
X 10205 101114 10184 10207
101307) 45) 101341 ) 3) ) )
[dB] 4) ) 3) 7)
)
-20 25.7 34.53 27.4 15.2573
-15 18.0 31.2 19.1 20.60 17.7 13.5 6.8806 16.9
3GPP
Release 100T 86 3GPP TR 36.942 V10.3.0 (2012-06)
-10 9.7 8.78 16 9.1 16.48 10.72 8.1 10.29 5.8 2.9315 6.9 11.12
-5 4.2 3.64 7.2 3.8 7.72 4.78 3.3 4.65 2.3 1.1669 2.5 5.13
0 1.7 1.37 2.9 1.5 3.2 1.85 1.2 1.98 0.8 0.427 0.9 2.32
5 0.6 0.52 1.1 0.6 1.23 0.64 0.4 0.77 0.3 0.1448 0.3 0.94
10 0.2 0.19 0.4 0.2 0.45 0.21 0.1 0.3 0.1 0.047 0.1 0.35
15 0.0 0.1 0.0 0.07 0 0.1 0.015 0
20 0.0 0.04
30.0 average
Qualcomm
25.0 (R4-101307)
LGE
(R4-101145)
20.0 NTT DOCOMO
(R4-101341)
Loss [%]
NOKIA
(R4-101389)
15.0 Huawei
(R4-102054)
Alcatel-Lucent
10.0 (R4-101114)
CATT
(R4-101173)
CMCC
5.0
(R4-101965)
ZTE
(R4-101701)
0.0 Samsung
-20 -10 0 10 20 (R4-101843)
Motorola
Figure 12.19 average Advanced E-UTRA uplink throughput loss (TPC set 1)
Table 12.21 average Advanced E-UTRA uplink throughput loss (TPC set 2)
Offse NTT Hua Alcatel- Sam Moto

Qual NOKIA CMCC ZTE
t LGE DOCOM wei Lucent sung rola
aver comm (R4- (R4- (R4-
value (R4- O (R4- (R4- (R4- (R4-
age (R4- 101389 101965 101701
X 101145) (R4- 102054 101114 10184 102077
101307) ) ) )
[dB] 101341) ) ) 3) )
-20 19.3 26.97 18.5 12.51
-15 11.8 18.4 12.3 14.34 11.3 8.2 5.22 12.6
-10 5.8 7.8 8.2 5.3 7.43 6.54 4.6 3.2 1.99 5.2 7.91
-5 2.3 3.34 3.3 2.1 2.95 2.58 1.7 1.1 0.69 1.9 3.63
0 0.9 1.31 1.2 0.8 1.1 0.91 0.6 0.4 0.23 0.7 1.42
5 0.3 0.61 0.4 0.3 0.4 0.30 0.2 0.2 0.07 0.2 0.51
10 0.1 0.29 0.1 0.1 0.14 0.10 0.1 0 0.02 0.1 0.26
15 0.0 0 0 0.03 0 0 0.01 0
3GPP
Release 100T 87 3GPP TR 36.942 V10.3.0 (2012-06)
30.0
average
Qualcomm
25.0 (R4-101307)
LGE
(R4-101145)
20.0 NTT DOCOMO
(R4-101341)
Loss [%]
NOKIA
15.0 (R4-101389)
Huawei
(R4-102054)
10.0 Alcatel-Lucent
(R4-101114)
CMCC
(R4-101965)
5.0
ZTE
(R4-101701)
Samsung
0.0 (R4-101843)
-20 -10 0 10 20 Motorola
(R4-102077)
Offset value X [dB]
Figure 12.20 average Advanced E-UTRA uplink throughput loss (TPC set 2)
Table 12.22 5%-ile Advanced E-UTRA uplink throughput loss (TPC set 1)
Offset Qual NTT Hua Alcatel- Sam Moto

LGE CMCC CATT ZTE
value aver comm DOCOMO wei Lucent sung rola
(R4- (R4- (R4- (R4-
X age (R4- (R4- (R4- (R4- (R4- (R4-
101145) 101965) 101173) 101701)
[dB] 101307) 101341) 102054) 101114) 101843) 102077)
-20 49.4 45.39 43 59.7369
-15 25.2 54.1 26.4 21.29 22.5 16 19.6959 16.4
-10 8.8 7.42 20.8 8.2 6.42 6.3 5 11.74 6.3135 5.5 10.38
-5 3.0 2.4 6.5 2.4 1.75 1.9 1.7 5.17 2.0052 1.8 4.36
0 1.0 0.81 1.9 1.0 0.46 0.6 0.5 1.99 0.635 0.1 1.73
5 0.3 0.29 0.6 0.3 0.14 0.1 0.2 0.64 0.2009 0 0.42
10 0.1 0.12 0.2 0.0 0.05 0 0 0.14 0.0635 0 0.18
15 0.0 0.1 0 0.01 0 0 0.06 0.0201 0
20 0.0 0.02
3GPP
Release 100T 88 3GPP TR 36.942 V10.3.0 (2012-06)
50.0 average
Qualcomm
(R4-101307)
40.0 LGE
(R4-101145)
NTT DOCOMO
(R4-101341)
30.0
Loss [%]
Huawei
(R4-102054)
Alcatel-Lucent
20.0 (R4-101114)
CMCC
(R4-101965)
CATT
10.0 (R4-101173)
ZTE
(R4-101701)
0.0 Samsung
(R4-101843)
-20 -10 0 10 20
Motorola
Figure 12.21 5%-ile Advanced E-UTRA uplink throughput loss (TPC set 1)
Table 12.23 5%-ile Advanced E-UTRA uplink throughput loss (TPC set 2)
Offset Qual NTT Hua Alcatel- Sam Moto

LGE CMCC ZTE
value aver comm DOCOMO wei Lucent sung rola
(R4- (R4- (R4-
X age (R4- (R4- (R4- (R4- (R4- (R4-
101145) 101965) 101701)
[dB] 101307) 101341) 102054) 101114) 101843) 102077)
-20 30.7 38.89 28.5 24.8201
-15 16.3 33.3 19.3 16.04 13.5 11.2 9.4545 11.2
-10 6.2 6.69 12.5 8.0 5.79 4.4 4 3.1966 4 7.28
-5 2.2 1.93 4.2 2.8 1.40 1.6 1.3 1.0335 1.6 3.63
0 0.8 0.803 1.4 1.3 0.38 0.6 0.4 0.3291 0.8 1.21
5 0.2 0.183 0.4 0.2 0.12 0.2 0.1 0.1043 0 0.23
10 0.0 0.01 0.1 0.0 0.04 0.1 0 0.033 0 0.1
15 0.0 0 0 0.01 0 0 0.0104 0
3GPP
Release 100T 89 3GPP TR 36.942 V10.3.0 (2012-06)
50.0
average
Qualcomm
40.0 (R4-101307)
LGE
(R4-101145)
30.0 NTT DOCOMO

Loss [%]
(R4-101341)
Huawei
(R4-102054)
20.0
Alcatel-Lucent
(R4-101114)
CMCC
10.0 (R4-101965)
ZTE
(R4-101701)
0.0 Samsung
(R4-101843)
-20 -10 0 10 20
Motorola
Figure 12.22 5%-ile Advanced E-UTRA uplink throughput loss (TPC set 2)
12.2.1.5 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 5 MHz UTRA victim
Victim system: 5 MHz UTRA
Cell Range 500 m
Simulation results for 5 MHz UTRA downlink capacity loss are presented in table 12.24 and figure 12.23.
Table 12.24 average 5 MHz UTRA downlink capacity loss
Offset NTT
Huawei Alcatel-Lucent Qualcomm ZTE
value average DOCOMO
(R4-101355) (R4-101114) (R4-102147) (R4-102188)
X [dB] (R4-101350)
-20 24.1 35.7 11.59 25
-15 16.0 19.1 6.31 22.3 16.3265
-10 8.9 10.2 3.03 11.1 9.83 10.2041
-5 4.7 5.1 1.23 4.5 4.29 8.1633
0 2.0 1.9 0.38 2.1 1.72 4.0816
5 0.9 0.6 0.09 0.7 0.57 2.3168
3GPP
Release 100T 90 3GPP TR 36.942 V10.3.0 (2012-06)
10 0.5 0.6 0.006 0 0.19 1.5

15 0.0 0 0.004 0 0.063
50.0 average
NTT DOCOMO
(R4-101350)
40.0 Huawei
(R4-101355)
Alcatel-Lucent
(R4-101114)
30.0 Qualcomm
Loss [%]
(R4-102147)
ZTE
(R4-102188)
20.0
10.0
0.0
-20 -10 0 10 20
Offset value X [dB]
Figure 12.23 average 5 MHz UTRA downlink capacity loss
12.2.1.6 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 5 MHz UTRA victim
Victim system: 5 MHz UTRA
Cell Range 500 m
Simulation results for 5 MHz UTRA uplink capacity loss are presented in table 12.25 and figure 12.24 for Advanced E-
UTRA TPC set 1 and in table 12.26 and figure 12.25 for Advanced E-UTRA TPC set 2.
Table 12.25 average 5 MHz UTRA uplink capacity loss (TPC set 1)
Alcatel-
Offset NTT NOKIA ZTE
Qualcomm Huawei Lucent
value average DOCOMO (R4- (R4-
(R4-101307) (R4-102054) (R4-
X [dB] (R4-101341) 101389) 102188)
101114)
-20 100.0 100
-15 100.0 100.0 100 100
-10 93.1 100 100.0 100 83.42 100 75
3GPP
Release 100T 91 3GPP TR 36.942 V10.3.0 (2012-06)
-5 86.3 100 100.0 100 69.59 100 48.0969

0 53.5 69.6 70.0 50 41.69 72.1 17.7778
5 16.5 19.7 21.4 15.15 10.79 25.2 6.6667
10 5.6 6.2 6.4 6.06 4.78 6.5 3.3333
15 2.2 2.2 2.857142857 1.52 2.11 2.4 2.3684
50.0
average
Qualcomm
40.0
(R4-101307)
NTT DOCOMO
(R4-101341)
30.0
Loss [%]
NOKIA
(R4-101389)
20.0 Huawei
(R4-102054)
Alcatel-Lucent
10.0 (R4-101114)
ZTE
(R4-102188)
0.0
-20 -10 0 10 20
Offset value X [dB]
Figure 12.24 average 5 MHz UTRA uplink capacity loss (TPC set 1)
Table 12.26 average 5 MHz UTRA uplink capacity loss (TPC set 2)
Offset NTT NOKIA Huawei Alcatel- ZTE

Qualcomm
value average DOCOMO (R4- (R4- Lucent (R4-
(R4-101307)
X [dB] (R4-101341) 101389) 102054) (R4-101114) 102188)
-20 100.0 100
-15 83.6 100.0 50.87 100
-10 37.4 46.04 46.4 33.33 11.89 44.9 41.746
-5 15.4 14.05 14.3 10.61 10.19 16.6 26.6667
0 5.0 4.58 5.0 4.55 2.11 5.2 8.3333
5 2.1 1.66 2.1 1.52 2.11 1.7 3.3333
10 1.1 0.68 1.4 1.52 0.87 0.5 1.6384
15 1.0 0.714285714 1.52 0.87 0.2 1.6384
3GPP
Release 100T 92 3GPP TR 36.942 V10.3.0 (2012-06)
50.0
average
40.0 Qualcomm
(R4-101307)
NTT DOCOMO
30.0 (R4-101341)
Loss [%]
NOKIA
(R4-101389)
20.0
Huawei
(R4-102054)
Alcatel-Lucent
10.0 (R4-101114)
ZTE
(R4-102188)
0.0
-20 -10 0 10 20
Offset value X [dB]
Figure 12.25 average 5 MHz UTRA uplink capacity loss (TPC set 2)
12.2.1.5 ACIR Downlink 40 MHz Advanced E-UTRA interferer – 1.6 MHz UTRA victim
Victim system: 1.6 MHz UTRA
Cell Range 500 m
Simulation results for 1.6 MHz UTRA downlink capacity loss are presented in table 12.27 and figure 12.26.
Table 12.27 average 1.6 MHz UTRA downlink capacity loss
Offset value CMCC CATT Huawei ZTE Td-tech

X [dB] (R4-102996) (R4-102476) (R4-103090) (R4-103305) (R4-103078)
-20 100.0 99.40 100
-15 97.2 91.33 86.1 99.12 90.41
-10 78.9 26.34 28.5 74.56 29.56
-5 15.2 11.18 10.4 14.56 12.29
0 5.5 5.03 4.18 5.22 4.21
5 2 2.51 3.94 3.54 2.32
10 0.5 1.04 1.89 0.54 0.7
15 0 0 0.06 0
3GPP
Release 100T 93 3GPP TR 36.942 V10.3.0 (2012-06)
LTE-A to UTRA (Capacity loss)

average
100.0
90.0
CMCC(R4-102996)
80.0
70.0
CATT (R4-102476)
Loss [%]
60.0
50.0
Huawei(R4-103090)
40.0
30.0
ZTE(R4-103305)
20.0
10.0
Td-tech(R4-103078)
0.0
-20 -10 0 10 20
Offset value X [dB]
Figure 12.26 average 1.6 MHz UTRA downlink capacity loss
12.2.1.6 ACIR Uplink 40 MHz Advanced E-UTRA interferer – 1.6 MHz UTRA victim
Victim system: 1.6 MHz UTRA
Cell Range 500 m
Simulation results for 5 MHz UTRA uplink capacity loss are presented in table 12.28 and figure 12.27 for Advanced E-
UTRA TPC set 1 and in table 12.29 and figure 12.28 for Advanced E-UTRA TPC set 2.
Table 12.28 average 1.6 MHz UTRA uplink capacity loss (TPC set 1)
Offset value CMCC CATT Huawei ZTE

X [dB] (R4-102996) (R4-102913) (R4-103090) (R4-103305)
-20 0 0 0 0
-15 0 0 0 0
-10 0 0 0 0
-5 0 0 0 0
0 0 0 0 0
5 0 0 0 0
10 0 0 0 0
3GPP
Release 100T 94 3GPP TR 36.942 V10.3.0 (2012-06)
LTE-A to LTE-A (Cell throughput, PC set 1)
100.0
90.0
80.0
70.0 average
CMCC (R4-102996)
Loss [%]
60.0
50.0 CATT (R4-102913)
40.0 Huawei(R4-103090)
30.0 ZTE(R4-103305)
20.0
10.0
0.0
-20 -15 -10 -5 0 5 10
Offset value [dB]
Figure 12.27 average 1.6 MHz UTRA uplink capacity loss (TPC set 1)
Table 12.29 average 1.6 MHz UTRA uplink capacity loss (TPC set 2)
Offset value CMCC CATT Huawei ZTE

X [dB] (R4-102996) (R4-102913) (R4-103090) (R4-103305)
-20 0 0 0 0
-15 0 0 0 0
-10 0 0 0 0
-5 0 0 0 0
0 0 0 0 0
5 0 0 0 0
10 0 0 0 0
3GPP
Release 100T 95 3GPP TR 36.942 V10.3.0 (2012-06)
LTE-A to LTE-A (Cell throughput, PC set 2)
50.0
40.0
average
30.0 CMCC (R4-102996)
Loss [%]
CATT (R4-102913)
Huawei(R4-103090)
20.0 ZTE(R4-103305)
10.0
0.0
-20 -15 -10 -5 0 5 10
Offset value [dB]
Figure 12.28 average 1.6 MHz UTRA uplink capacity loss (TPC set 2)
3GPP
Release 100T 96 3GPP TR 36.942 V10.3.0 (2012-06)
Annex A (informative):
Link Level Performance Model
A.1 Description
Annex A.2 provides detail on how the baseline throughput curves are derived. It shows that the throughput of a modem
with link adaptation can be approximated by an attenuated and truncated form of the Shannon bound. (The Shannon
bound represents the maximum theoretical throughput than can be achieved over an AWGN channel for a given SNR).
The following equations approximate the throughput over a channel with a given SNR, when using link adaptation:
Thr = 0 for SNIR < SNIR MIN

Throughput , Thr , bps / Hz = Thr = α.S(SNIR) for SNIR min < SNIR < SNIR MAX
Thr = ThrMAX for SNIR > SNIR MAX
Where: S(SNIR) is the Shannon bound: S(SNIR) = log 2 (1+SNIR) bps/Hz
α Attenuation factor, representing implementation losses

SNR MIN Minimum SNIR of the codeset, dB
Thr MAX Maximum throughput of the codeset, bps/Hz
SNIRMAX SNIR at which max throughput is reached S-1(Thr MAX ), dB
The parameters α, SNRMIN and THRMAX can be chosen to represent different modem implementations and link
conditions. The parameters proposed in table 1 represent a baseline case, which assumes:
- 1:2 antenna configurations
- Typical Urban fast fading channel model (10kmph DL, 3kmph UL)
- Link Adaptation (see table 1 for details of highest and lowest rate codes)
- Channel prediction
- HARQ
Table A.1 Parameters describing baseline Link Level performance for E-UTRA Co-existence
simulations
Parameter DL UL Notes
α, attenuation 0.6 0.4 Represents implementation losses
SNIR MIN , dB -10 -10 Based on QPSK, 1/8 rate (DL) & 1/5 rate (UL)
Thru MAX , bps/Hz 4.4 2.0 Based on 64QAM 4/5 (DL) & 16QAM 3/4 (UL)
Table A.1 shows parameters proposed for the baseline E-UTRA DL and UL. Table A.2 shows the resulting look up
table, which is plotted in Figure A.1. Table A.2 gives throughput in terms of spectral efficiency (bps per Hz), and per
375khz Resource Block (RB), in kbps.
3GPP
Release 100T 97 3GPP TR 36.942 V10.3.0 (2012-06)
5
Shannon
Throughput, bps/Hz
4
DL
3 UL
2
0
-15 -10 -5 0 5 10 15 20 25
SNIR, dB
Figure A.1 Throughput vs SNR for Baseline E-UTRA Coexistence Studies
Table A.2 Look-Up-Table of UL and DL Throughput vs. SNIR for Baseline E-UTRA Coexistence
Studies
Throughput Throughput
kbps per kbps per
SNIR bps/Hz 375kHz RB SNIR bps/Hz 375kHz RB
dB DL UL DL UL dB DL UL DL UL
-15 0 0 0 0 6 1.39 0.93 521 347
-14 0 0 0 0 7 1.55 1.04 582 388
-13 0 0 0 0 8 1.72 1.15 646 430
-12 0 0 0 0 9 1.90 1.26 711 474
-11 0 0 0 0 10 2.08 1.38 778 519
-10 0.08 0.06 31 21 11 2.26 1.51 847 565
-9 0.10 0.07 38 26 12 2.44 1.63 917 611
-8 0.13 0.08 48 32 13 2.63 1.76 988 658
-7 0.16 0.10 59 39 14 2.82 1.88 1059 706
-6 0.19 0.13 73 48 15 3.02 2.00 1131 750
-5 0.24 0.16 89 59 16 3.21 2.00 1204 750
-4 0.29 0.19 109 73 17 3.41 2.00 1277 750
-3 0.35 0.23 132 88 18 3.60 2.00 1350 750
-2 0.42 0.28 159 106 19 3.80 2.00 1424 750
-1 0.51 0.34 190 127 20 3.99 2.00 1498 750
0 0.60 0.40 225 150 21 4.19 2.00 1572 750
1 0.71 0.47 265 176 22 4.39 2.00 1646 750
2 0.82 0.55 308 206 23 4.40 2.00 1650 750
3 0.95 0.63 356 237 24 4.40 2.00 1650 750
4 1.09 0.72 408 272 25 4.40 2.00 1650 750
5 1.23 0.82 463 309
3GPP
Release 100T 98 3GPP TR 36.942 V10.3.0 (2012-06)
A.2 Modelling of Link Adaptation
Input Code modulate demodulate decode Output

data bits SNR data bits
Coded modulation Coded

bits symbols bits
Figure A.3 Coding and Modulation for Transmission of data over a radio link
Figure A.3 shows a radio transmitter and receiver. The throughput over a radio link is the number of data bits that can
be successfully transmitted per modulation symbol. Coding (more specifically, Forward Error Correction) adds
redundant bits to the data bits which can correct errors in the received bits. The degree of coding is determined by its
rate, the proportion of data bits to coded bits. This typically varies from 1/8th to 4/5ths. Coded bits are then converted
into modulation symbols. The order of the modulation determines the number coded bits that can be transmitted per
modulation symbol. Typical examples are QPSK and 16 QAM, which have 2 and 4 bits per modulation symbol,
respectively.
The maximum throughput of a given MCS (Modulation and Coding Scheme) is the product of the rate and the number
of bits per modulation symbol. Throughput has units of data bits per modulation symbol. This is commonly normalised
to a channel of unity bandwidth, which carries one symbol per second. The units of throughput then become bits per
second, per Hz.
A given MCS requires a certain SNIR (measured at the rx antenna) to operate with an acceptably low BER (Bit Error
Rate) in the output data. An MCS with a higher throughput needs a higher SNIR to operate. AMC (Adaptive
Modulation and Coding) works by measuring and feeding back the channel SNIR to the transmitter, which then chooses
a suitable MCS from a ‘codeset’ to maximise throughput at that SNIR. A codeset contains many MCS’s and is designed
to cover a range of SNRs. An example of a codeset is shown in Figure A.4. Each MCS in the codeset has the highest
throughput for a 1-2dB range of SNIR.
7
MCS-1 [QPSK,R=1/8]
MCS-2 [QPSK,R=1/5]
6
MCS-3 [QPSK,R=1/4]
Throughput, bits per second per Hz
MCS-4 [QPSK,R=1/3]
5 MCS-5 [QPSK,R=1/2]
MCS-6 [QPSK,R=2/3]
MCS-7 [QPSK,R=4/5]
4
MCS-8 [16 QAM,R=1/2]
MCS-9 [16 QAM,R=2/3]
3 MCS-10 [16 QAM,R=4/5]
MCS-11 [64 QAM,R=2/3]
2 MCS-12 [64 QAM,R=3/4]
MCS-13 [64 QAM,R=4/5]
Shannon
1
0
-10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20
SNR, dB
Figure A.4 Throughput of a set of Coding and Modulation Combinations, AWGN channels assumed
Figure A.4 also shows the Shannon bound, which represents the maximum theoretical throughput that can be achieved
over an AWGN channel with a given SNR. The example AMC system achieves around 0.75x the throughput of the
3GPP
Release 100T 99 3GPP TR 36.942 V10.3.0 (2012-06)
Shannon bound, over the range of SNR which it operates. We can approximate the performance of AMC with an
attenuated and truncated form of the Shannon bound as shown in Figure A.5.
8
1:1 AWGN Shannon
7 1:1 AWGN MTS Codeset
AMC Approximation: 0.75xShannon
6
Throughput, bps/Hz
0
-10 -5 0 5 10 15 20 25
Mean SNR, dB
Figure A.5 Approximating AMC With an Attenuated and Truncated form of the Shannon Bound
The following equations approximate the throughput over a channel with a given SNR, when using AMC:

Throughput , Thr = Thr = α.S(SNIR) for SNIR min < SNIR < SNIR MAX
Where:
S(SNIR) is the Shannon bound: S(SNIR) = log 2 (1+SNIR)
α Attenuation factor (0.75 for the example codeset)

SNR MIN Minimum SNIR of the codeset (-6.5dB for the example codeset)
Thr MAX Maximum throughput (4.8 bit/sec/Hz for the example codeset)
SNIRMAX SNIR at which max throughput is reached S-1(Thr MAX ) (17dB for the example codeset)
A.3 UTRA 3.84 Mcps TDD HSDPA Link Level Performance

The throughput is derived from the HSDPA link level results of [8] and is found to match a truncated Shannon bound
with an attenuation of 0.5. The HSDPA UTRA 3.84 Mcps TDD throughput is normalised to 15 timeslots and the
spectral efficiency is found assuming a bandwidth of 5MHz. The spectral efficiency in table A.3 is presented as a
function of the SINR in a timeslot. Figure A.6 shows the UTRA 3.84 Mcps TDD spectral efficiency as a function of
SINR in a timeslot and the attenuated Shannon approximation. NOTE: RX Diversity is not employed.
Table A.3 SINR in a timeslot to spectral efficiency mapping
SINR in timeslot (dB) spectral efficiency (bps / Hz)

-6.5 0.11
-3.5 0.22
-0.5 0.44
3GPP
Release 100T 100 3GPP TR 36.942 V10.3.0 (2012-06)
1.8 0.66
5.0 0.99
7.0 1.32
11.2 1.99
14.2 2.38
Shannon T D-CDMA from [8] T D-CDMA approx alpha = 0.5
7
Spectral Efficiency (bps/Hz)
0
-15 -10 -5 0 5 10 15 20 25 30
SINR (dB)
Figure A.6 Throughput per DL Channel vs. SINR for Downlink UTRA 3.84 Mcps TDD (HSDPA)
The attenuated Shannon approximation to UTRA 3.84 Mcps TDD spectral efficiency is based on the approach used for
E-UTRA. The maximum spectral efficiency is derived assuming a code rate of 0.9 and 16QAM modulation. The
Shannon approximation to UTRA 3.84 Mcps TDD spectral efficiency is:

Throughput , Thr , bps / Hz = Thr = α.S(SNIR) for SNIR min < SNIR < SNIR MAX
where the following parameters are applied:
Table A.4 Parameters describing baseline UTRA 3.84 Mcps TDD performance Look-Up-table
Parameter DL Notes
α, attenuation 0.5 Represents implementation losses
SNIR MIN , dB -10 Based on QPSK, 1/12 rate (DL) without Rx Diversity
Thru MAX , bps/Hz 2.38 Based on 16QAM rate 0.9 (DL)
SNIR MAX , dB 14.20
3GPP
Release 100T 101 3GPP TR 36.942 V10.3.0 (2012-06)
A.4 Link Level Performance for E-UTRA TDD (LCR TDD frame
structure based)
The throughput of a modem with link adaptation can be approximated by an attenuated and truncated form of the
Shannon bound. (The Shannon bound represents the maximum theoretical throughput than can be achieved over an
AWGN channel for a given SNR). The following equations approximate the throughput over a channel with a given
SNR, when using link adaptation:
=Thr 0 for SNIR < SNIR MIN

Thr α ⋅ S(SNIR)
Throughput, Thr, bps/Hz == for SNIR min < SNIR < SNIR MAX
=Thr ThrMAX for SNIR > SNIR MAX
Where:
S(SNIR) Shannon bound, S(SNIR) =log 2 (1+SNIR) bps/Hz
α Attenuation factor, representing implementation losses

SNR MIN Minimum SNIR of the codeset, dB
Thr MAX Maximum throughput of the codeset, bps/Hz
SNIRMAX SNIR at which max throughput is reached S-1(Thr MAX ), dB
The parameters α, SNRMIN and THRMAX can be chosen to represent different modem implementations and link
conditions. The parameters proposed in table 1 represent a baseline case, which assumes:
• 1:1 antenna configurations
• AWGN channel model
• Link Adaptation (see table A.X for details of highest and lowest rate codes)
• No HARQ
Table A.5 Parameters describing baseline Link Level performance for E-UTRA TDD Co-existence
simulations
Parameter UL DL Notes
α, attenuation 0.55 0.6 Represents implementation losses
SNIR MIN , dB -4.9 -4.5 Based on BPSK, 1/7 rate for UL and QPSK 1/8 for DL
SNIR MAX , dB 11.45 16.72 Based on16QAM, 4/5 rate
Thru MAX , bps/Hz 2.15 3.4 Based on 16QAM, 4/5 rate
Throughput vs. SNR curves are plotted in Figure A.7 for uplink and Figure A.8 for downlink. Table A.6 and table A.7
present throughput in terms of spectral efficiency (bps/Hz), and per 375kHz Resource Block (RB), in kbps.
3GPP
Release 100T 102 3GPP TR 36.942 V10.3.0 (2012-06)
Figure A.7 Throughput vs SNR for Baseline E-UTRA Coexistence Studies for uplink
Figure A.8 Throughput vs SNR for Baseline E-UTRA Coexistence Studies for downlink
3GPP
Release 100T 103 3GPP TR 36.942 V10.3.0 (2012-06)
Table A.6 Look-Up-Table of UL Throughput vs SNIR for Baseline E-UTRA-TDD Coexistence Studies
SNIR(dB) bps/Hz kbps per SNIR(dB) bps/Hz kbps per
375kHz RB 375kHz RB
-6 0 0 5 1.13 424.33
-5 0 0 6 1.27 477.77
-4 0.27 99.72 7 1.42 533.74
-3 0.32 120.88 8 1.58 591.89
-2 0.39 145.55 9 1.74 651.92
-1 0.46 173.96 10 1.90 713.51
0 0.55 206.25 11 2.07 776.41
1 0.65 242.48 12 2.15 805.07
2 0.75 282.58 13 2.15 805.07
3 0.87 326.43 14 2.15 805.07
4 1.00 373.78 15 2.15 805.07
Table A.7 Look-Up-Table of DL Throughput vs SNIR for Baseline E-UTRA-TDD Coexistence Studies
SNIR(dB) bps/Hz kbps per SNIR(dB) bps/Hz kbps per
375kHz RB 375kHz RB
-7 0 0 7 1.6 584.3
-6 0 0 8 1.7 647.9
-5 0 0 9 1.9 713.6
-4 0.3 109.3 10 2.1 781.0
-3 0.4 132.3 11 2.3 849.9
-2 0.4 159.3 12 2.5 919.9
-1 0.5 190.4 13 2.6 990.9
0 0.6 225.8 14 2.8 1062.7
1 0.7 265.4 15 3.0 1135.1
2 0.8 309.3 16 3.2 1208.1
3 1.0 357.3 17 3.4 1260.9
4 1.1 409.2 18 3.4 1260.9
6 1.2 464.5 19 3.4 1260.9
7 1.4 523.0 20 3.4 1260.9
Annex B (informative):
Smart Antenna Model for UTRA 1.28 Mcps TDD
B.1 Description
Considering beam forming function of smart antenna, the following five basic beam forming pattern is provided with
their main beam pointing to 0°,30°,45°,60° and 70° respectively. The beam patterns pointing to -30°,-45°,-60° and -70°
can be derived through the image of the above beam patterns. Thus, we can get nine angles beamforming radioation
pattern. The gain of blow -90 and above 90 is assumed as -∞ by using the ideal isolation. In the simulation each UE will
select the most adjacent (in angle) beam pattern for signal strength and interference calculation accroding the the angle
calculated from the UE position and BS sector antenna direction. For example if a UE ‘s angle to the direction of the
sector is 250, the 300 beam pattern will be selected. Then the selected beam pattern will be shifted -50, by which the
main beam will pointing the UE. The signal strengh and interference from different direction will be calculated based
on the shifted pattern. The shifted angle out of [-90°,90°] will be transfered inside [-90°,90°] by horizontal imaging.
3GPP
Release 100T 104 3GPP TR 36.942 V10.3.0 (2012-06)
Figure B.1: 0° beam forming pattern
3GPP
Release 100T 105 3GPP TR 36.942 V10.3.0 (2012-06)
3GPP
Release 100T 106 3GPP TR 36.942 V10.3.0 (2012-06)
3GPP
Release 100T 107 3GPP TR 36.942 V10.3.0 (2012-06)
Annex C (informative):
Simulation assumptions for LTE-A coexistence
Table C.1 Simulation assumptions for LTE-A coexistence
Parameter Assumption (common)

Environment Macro cell, Urban area, Uncoordinated deployment
Carrier frequency 2000 MHz
Hexagonal grid, 19 cell sites, 57 sectors with BTS in the corner of the cell ,
Cellular layout
65-degree sectored beam.
BTS antenna gain
15 dBi
(include feeder loss)
BTS antenna frontback ratio (A m ) 20 dB
BTS antenna height 30 m
Inter-site distance 750 m
Pathloss model 128.1+37.6log10(r) + 21*log 10 (f c/2.0)
log-normal fade shadow 10 dB
Shadowing correlation Between cells: 0.5, Between sectors: 1.0
MCL (including antenna gain) 70 dB
Handover margin 3 dB
white noise power density -174 dBm/Hz
BTS noise figure 5 dB
UE noise figure 9 dB
Scheduling algorithm Round Robin

Parameter Assumption (5 MHz UTRA)
system bandwidth 5 MHz
BS max Tx power 43 dBm
UE max Tx power 21 dBm

UE min Tx power -50 dBm
Traffic model speech (8kbps), full-buffer
N/A (UL)
non orthogonality factor
0.4 (DL)
6.1 dB (UL)
Target Eb/N0
7.9 dB (DL)
Parameter Assumption (1.6 MHz UTRA)
system bandwidth 1.6 MHz
Smart antenna model TR 36.942 Annex <B>
Traffic model speech (12.2kbps), full-buffer
non orthogonality factor 0.22 (UL)
3GPP
Release 100T 108 3GPP TR 36.942 V10.3.0 (2012-06)
0.2 (DL)
-2.5 dB (UL)
Target SIR
-2.5 dB (DL)
Parameter Assumption (LTE)

Power control algorithm Fractional TPC
P 0PUSCH -101.0 dBm (TPC set1), -92.24 dBm (TCP set 2)
alpha 1.0 (TPC set 1), 0.8 (TPC set 2)
Traffic model full-buffer
Resource Block (RB) size 180kHz, total: 50 RBs
16 RBs (total: 48 RBs) (UL),
RB number per active UEs
50 RBs (DL)
number of active UEs 3 UEs (UL), 1 UE (DL)
Link simulation interface Attenuated and truncated form of the Shannon bound in TR36.942.doc
Parameter Assumption (LTE-A)

Power control algorithm Fractional TPC
P 0PUSCH -101.0 dBm (TPC set1), -92.24 dBm (TCP set 2)
alpha 1.0 (TPC set 1), 0.8 (TPC set 2)
Traffic model full-buffer
Resource Block (RB) size 180kHz, total: 200 RBs
16 RBs (total: 192 RBs) (UL),
RB number per active UEs
200 RBs (DL)
number of active UEs 12 UEs (UL), 1 UE (DL)
Link simulation interface Attenuated and truncated form of the Shannon bound in TR36.942.doc
3GPP
Release 100T 109 3GPP TR 36.942 V10.3.0 (2012-06)
Annex D (informative):
Change history
Change history
Date TSG # TSG Doc. CR Rev Subject/Comment Old New
2005-11 R4 #37 R4-051134 TR created
2006-02 R4 #38 R4-060353 Approved Documents included:R4-060301, R4-060347, R4- 0.1.0
060348, R4-060349, R4-060350, R4-060351, R4-060352
2006-05 R4 #39 R4-060373 Approved Documents included:R4-060372, R4-060390 0.1.0 0.2.0
2006-05 R4 #39 R4-060641 Approved Documents included:R4-060639, R4-06040, R4-060673, 0.2.0 0.3.0
R4-060674, R4-060680, R4-060699
2006-09 R4 #40 R4-061216 Approved Documents included:R4-061054, R4-061066, R4- 0.3.0 0.4.0
060973, R4-061067
2006-11 R4 #41 R4-061359 Approved Documents included: R4-061312, R4-061319, R4- 0.4.0 0.5.0
061344, R4-061366, R4-061374,
2007-02 R4#42 R4-070280 TR number 36.942 assigned 0.5.0 0.6.0
2007-02 R4#42 R4-070289 Approved Documents included: R4-070288, R4-070295, R4- 0.6.0 1.0.0
070319
2007-04 R4#42bis R4-070445 Editorial cleanup 1.0.0 1.0.1
2007-04 R4#42bis R4-070457 Approved Documents included: R4-070459 1.0.1 1.1.0
2007-06 R4#44 R4-071172 Approved Documents included: R4-070931, R4-071146 1.1.0 1.2.0
2007-08 R4#44bis R4- Approved Documents included: R4-071173, R4-071212 1.2.0 1.3.0
0711535
2007-10 R4#44bis R4-071753 Approved Document included: R4-071535 1.3.0 1.4.0
2008-02 R4 #46 R4-080435 Approved Document included: R4-080309 1.4.0 1.5.0
2008-08 R4#48 R4-081728 Approved Document included: R4-081638 1.5.0 1.6.0
2008-08 R4#48 R4-082117 Approved Document included: R4-082085 1.6.0 1.7.0
Editorial clen-up.
2008-09 RP-41 RP-080592 Presentation for Approval 1.7.0 2.0.0
2008-09 RP-41 RP-080592 TR 36.942 V2.0.0 2.0.0 8.0.0
2008-12 RP-42 RP-080906 1 Rationales of unwanted emissions in TR 36.942 8.0.0 8.1.0
2008-12 RP-42 RP-080907 2 1 Correction of unwanted emission requirements for multi-carrier BS 8.0.0 8.1.0
2009-05 RP-44 RP-090544 3 Clarification of requirements for multicarrier BS 8.1.0 8.2.0
2009-12 SP-46 Automatic upgrade from previous Release 8.2.0 9.0.0
2010-04 Fix typo in version number on cover page 9.0.0 9.0.1
2010-06 RP-48 RP-100634 004 3 LTE-Advanced Co-existence 9.0.1 10.0.0
2010-09 RP-49 RP-100914 007 1 CR TR 36.942-10.0.0 Clause 5.1.1.4.1 Uplink Asymmetrical 10.0.0 10.1.0
Bandwidths ACIR
2010-12 RP-50 RP-101344 010 CR TR 36.942 v10.1.0 annex A.4 Link Level Performance for E- 10.1.0 10.2.0
UTRA TDD
2010-12 RP-50 RP-101359 009 Additional of LTE-Advanced co-existence simulation results 10.1.0 10.2.0
(scenario #4)
2012-06 RP-56 RP-120778 011 1 Clarification of unwanted emissions requirements for TS 36.942 10.2.0 10.3.0
Rel-10
2012-06 RP-56 RP-120766 014 1 Clarification of uplink power control in TR36.942 10.2.0 10.3.0
3GPP

3GPP TR 36.942

Uploaded by

Copyright:

Available Formats

3GPP TR 36.942

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3GPP TR 36.942

Uploaded by

Copyright:

Available Formats

3GPP TR 36.942 V10.3.

3rd Generation Partnership Project;

3GPP support office address

No part may be reproduced except as authorized by written permission.

6 System scenarios ............................................................................................................................... 26

12.1.4 Uplink power control ........................................................................................................................... 76

Annex A (informative): Link Level Performance Model ................................................................. 96

Annex C (informative): Simulation assumptions for LTE-A coexistence...................................... 107

x the first digit:

1 presented to TSG for information;

2 presented to TSG for approval;

3 or greater indicates TSG approved document under change control.

• For a specific reference, subsequent revisions do not apply.

[3] 3GPP TR 25.942, “Radio Frequency (RF) system scenarios”

[4] 3GPP TR 25.814, “Physical Layer Aspects for Evolved UTRA”

[7] 3GPP TR 25.951, “FDD Base Station (BS) classification”

[9] R4-070235, “Analysis of co-existence simulation results”, RAN4#42

[13] R4-070263, “Proposal on LTE ACLR requirements for UE”, RAN4#42

[15] R4-070391, “LTE 900 - GSM 900 Downlink Coexistence”, RAN4#42bis

[18] R4-070392 “LTE-LTE Coexistence with asymmetrical bandwidth”, RAN4#42bis

[21] 3GPP TS 36.141, ”Base Station (BS) conformance testing”

[22] Recommendation ITU-R SM.329-10, “Unwanted emissions in the spurious domain”

[27] R4-070430, "UE ACS and BS ACLRs" (Fujitsu ).

3 Definitions, symbols and abbreviations

ACIR Adjacent Channel Interference Ratio

4.1 Interference scenarios

4.2 Antenna Models

4.2.1.1 BS antenna radiation pattern

Figure 4.1: Antenna Pattern for 3-Sector Cells

4.2.1.2 BS antenna heights and antenna gains for macro cells

Table 4.3: Antenna height and gain for Macro Cells

Rural Area Urban Area

4.2.3 MIMO antenna Characteristics

4.3 Cell definitions

4.4 Cell layouts

4.4.1 Single operator cell layouts

4.4.1.1 Macro cellular deployment

Figure 4.2: Single operator cell layout

4.4.2 Multi operator / Multi layer cell layouts

4.4.2.1 Uncoordinated macro cellular deployment

Figure 4.3: Multi operator cell layout - uncoordinated operation

4.4.2.2 Coordinated macro cellular deployment

Figure 4.4: Multi operator cell layout - coordinated operation

4.5 Propagation conditions and channel models

4.5.1 Received signal

Table 4.4: Minimum Coupling Losses

Environment Scenario MCL

RX_PWR = TX_PWR – Max (pathloss – G_TX – G_RX, MCL)

RX_PWR is the received signal power

TX_PWR is the transmitted signal power

G_TX is the transmitter antenna gain

G_RX is the receiver antenna gain

4.5.2 Macro cell propagation model – Urban Area

L = 40 ⋅ (1 − 4 ⋅10 −3 ⋅ Dhb) ⋅ log10 (R) − 18 ⋅ log10 (Dhb) + 21 ⋅ log10 (f) + 80dB

R is the base station-UE separation in kilometres

f is the carrier frequency in MHz

L = 120,9 + 37,6log10 (R)

R is the base station-UE separation in kilometres

L = 128,1 + 37,6log10 (R)