Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 5K views

    YANMAR YM Service Manual

    Uploaded by

    Marcin Losy
    Yanmar service manual

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd

    YANMAR YM Service Manual

    Uploaded by

    Marcin Losy
    5K views231 pages
    Yanmar service manual

    Original Title

    YANMAR YM service manual

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Yanmar service manual

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    5K views231 pages

    YANMAR YM Service Manual

    Uploaded by

    Marcin Losy
    Yanmar service manual

    Copyright:

    © All Rights Reserved
    Download as PDF or read online from Scribd
    Download as pdf
    You are on page 1of 231
    YANMAR. YANMAR. SERVICE MANUAL MARINE DIESEL ENGINE 3YM30 /3YM20/2YM15 YANMAR CO.,LTD. Publication No. M9961-03E101 History of Revision Manual Name | Service Manual for Marine Diesel Engine Engine Model: _| SYM30/3YM20/2YM15 Number! pate of | Reason for Correction item | Corrected cf | revision | correction Outline of correction No (page) by revision (pag y New edition March 2004 Ri April |Add: Eug. — ]1. Specifications table added Quality 25, | Model 2YM15 | 2. Engine outline added. Control 2005 3. Piping diagram added. Dept 4. Olher data added Marine Factory Conected |. Front cover added to engine | P6-P.O data outline @YM30, | 2, Notice on seawater pump P32 3YM20) rotating direction was changed Incorrect word corrected Printed in Japan M9961-03E101 Ri FOREWORD This service manual has been complied for engineers engaged in sales, service, inspection and maintenance. Accordingly, descriptions of the construction and functions of the engine are emphasized in this manual, while items, which should already be common knowledge, are omitted, One characteristic of a marine diesel engine is that its performance in a vessel is governed by the applicability of the vessel's hull construction and its steering system. Engine installation, fiting out and propeller selection have a substantial effect on the performance of the engine and the vessel. Moreover, when the engine runs unevenly or when trouble occurs, itis essential to check a wide range of operating conditions - such as installation to the full and suitability of the ship's piping and propeller - and not just the engine itself. To get maximum performance from this engine, you should completely understand its functions, construction and capabilities, as well as proper use and servicing, Use this manual as a handy reference in daily inspection and maintenance, and as a text for engineering guidance. Model 3YM30 has been used for the illustrations in this service manual, but they apply to other models in the 3YM series engines. California California Proposition 65 Warning Proposition 65 Warning Diesel engine exhaust and some of its Battery posts, terminals, and related ac- constituents are known to the State of cessories contain lead and lead com- California to cause cancer, birth de- pounds, chemicals known to the State fects, and other reproductive harm of California to cause cancer and repro- ductive harm. Wash hands, after handling (©2005 YANMAR CO., LTD All rights reserved. This manual may not be reproduced or copied, in whole or in part, ‘without the written permission of YANMAR Co, LTD. Ri CONTENTS 1, General .. 4.1 Exterior views 4.2 Specifications 4.3 Fuel oil, lubricating oil and cooling water 1.3.1 Fuel oil 1.3.2 Lubricating oll 1.3.3 Cooling water. 4.4 Engine outline 4.5 Piping diagrams 1.6 Exhaust gas emission regulation 1.6.1 Engine identification (EPA/ARB) 1.6.2 Exhaust gas emission standard (EPA/ARB) 1.6.3 Guarantee conditions for emission standard (EPA/ARB) 2. Inspection and adjustment 2.4 Periodic maintenance schedule 2.2 Periodic inspection and maintenance procedure 2.2.1 Check before starting 2.2.2 inspection after initial 50 hours or one month operation 2.2.3 Inspection every 50 hours or monthly 2.2.4 Inspection every 100 hours six months. 2.2.5 Inspection every 150 hours or one year. 2.2.6 Inspection every 250 hours or one year. 2.2.7 Inspection every 1,000 hours or four years. 2.3 Adjusting the no-load maximum or minimum speed 2.4 Sensor Inspection 2.4.1 Oil pressure switch... 2.4.2 Thermo switeh 2.5 Thermostat inspection 2.6 Adjusting operation 2.6.1 Preliminary precautions 2.6.2 Adjusting operation procedure 2.6.3 Check points and precautions during running 2.7 Long storage 3. Troubleshooting 3.1 Preparation before troubleshooting 3.2 Quick reference chart for troubleshooting 3.3 Troubleshooting (Concerning engine and fuel injection equipment) 3.4 Troubleshooting by measuring compression pressure 4, Disassembly and reassembly 4.1 Disassembly and reassembly precautions 4.2 Disassembly and reassembly tools 4.2.1 General hand tools. 4.2.2 Special hand tools. 4.2.3 Measuring instruments. 4.2.4 Other material 4.3 Disassembly and reassembly 4.3.1 Disassembly. 4.3.2 Reassembly 5. Inspection and servicing of basic engine parts 5.1 Cylinder block 5.1.4 Inspection of parts 5.4.2 Cleaning of oil holes. 5.1.3 Color check procedure 5.4.4 Replacement of cap plugs 5.1.5 Cylinder bore measurement. 5.2 Cylinder head 5.2.1 Inspecting the oylinder head 5.2.2 Valve seat correction procedure 5.2.3 Intake/exhaust valves, valve guides 5.2.4 Valve springs 5.2.5 Assembling the cylinder head 5.2.6 Measuring top clearance. 5.2.7 Intake and exhaust rocker arms. 5.2.8 Adjustment of valve clearance 5.3 Piston and piston pins 5.3.1 Piston 5.3.2 Piston pin 5.3.3 Piston rings 5.4 Connecting rod 5.4.1 Inspecting the connection rod 5.4.2 Crank pin metal 5.4.3 Piston pin bushing, 5.4.4 Assembling piston and connecting rod 5.5 Crankshaft and main bearing 5.5.1 Crankshaft 5.5.2 Main bearing 62 64 64 65 65 68 n 15 77 7 89 104 104 404 404 404 105 106 107 108 109 110 112 113 114 114 118 116 116 117 118 121 424 122 124 124 125 125 127 5.6 Camshaft and tappets 5.6.1 Camshaft 5.6.2 Tappets 5.7 Timing gear 5.7.1 Inspecting the gears. 5.7.2 Gear timing marks... 5.8 Flywheel and housing 5.8.1 Position of top dead center and fuel injection timing, 5.8.2 Damper disc 6. Fuel injection equipment 6.1 Fuel Injection pump/governor 6.1.1 Fuel system diagram, 6.1.2 Fuel injection pump service data and adjustment 6.1.3 Fuel injection pump structure. 6.1.4 Removing a fuel injection pump 61.5 Installing a fuel injection pump 6.1.6 Adjusting fuel injection timing 6.1.7 Troubleshooting of fuel injection pump 6.1.8 Major faults and troubleshooting 6.2 Fuel feed pump 6.2.1 Construction of fuel feed pump. 6.2.2 Fuel feed pump specifications 6.2.3 Disassembly and reassembly of fuel feed pump 6.2.4 Fuel feed pump inspection 6.3 Fuel filter 6.3.1 Fue! fier specifications. 6.3.2 Fuel fiter inspection 6.4 Fuel tank 7. Intake and exhaust system 7.1 Intake system 7.4.4 Breather system (A reductor to intake air system of blowby gas). 7.4.2 Diaphragm assy inspection. 7.2 Exhaust system 7.2.4 Construction 7.2.2 Mixing elbow inspection 8. Lubrication system 8.1 Lubrication system 8.2 Lube oil pump 8.2.1 Lube oll pump construction 128 128 130 131 131 131 132 132 133, 134 134 134 135 139 140 140 140 141 141 144 144 144 145 145 147 147 147 148 149 149 149, 150 151 151 151 152 152 153 153 8.2.2 Speoifications of lube oil pump 8.2.3 Lube oil pump disassembly and reassembly 8.2.4 Lube oil pump inspection... 8.2.5 Pressure control valve construction... 8.3 Lube oil filter, 8.3.1 Lube oil fiter construction 8.3.2 Lube oll iter replacement. 8.4 Rotary waste oil pump (Optional) 9. Cooling water system 9.1 Cooling water system 9.2 Seawater pump 9.2.1 Spesifications of seawater pump. 9.2.2 Seawater pump disassembly 9.2.3 Seawater pump Inspection 9.2.4 Seawater pump reassembly 9.3 Fresh water pump . 9.3.1 Fresh water pump construction. 9.3.2 Specifications of fresh water pump 9.3.3 Fresh water pump disassembly 9.3.4 WFresh water pump inspection 9.4 Heat exchanger 9.4.1 Heat exchanger construction 9.4.2 Disassembly and reassembly of the heat exchanger 9.4.3 Heat exchanger inspection 9.5 Pressure cap and coolant recovery tank 9.5.1 Pressure cap construction ... 9.5.2 Pressure cap pressure control. 9.5.3 Pressure cap inspection... 9.5.4 Replacing filler neck, 9.5.5 Function of the coolant recovery tank 9.5.6 Specifications of coolant recovery tank. 9.5.7 Mounting the coolant recovery tank... 9.5.8 Precautions on usage of the coolant recovery tank. 9.6 Thermostat .. 9.6.1 Functioning of thermostat 96.2 Thermostat construction 9.6.3 Characteristics of thermostat 9.6.4 Thermostat inspection 9.6.5 Testing the thermostat a 153, 153, 184 184 155 155 155 156 187 157 159 159 159 160 161 162 162 162 163 163 165 165 165 165 167 168 168 168 168 169 169 169 169 169 169 9.7 Bilge pump and bilge strainer (Optional) 9.7.1 Introduction 9.7.2 Description 9.7.3 Cautions 9.7.4 Assembly procedure 8.7.5 Cautions for assembling 9.7.6 Troubleshooting 10. Reduction and reversing gear 10.1 Specifications 11. Remote control (Optional) 11.1 Remote control system 11.4.4 Construction of remote control system 11.1.2 Remote control device components, 11.2 Remote control installation 11.3 Remote control inspection 11.4 Remote control adjustment 12. Electrical system 12.1 Electrical system 12.1.1 Wiring diagram. 12.2 Battery 12.3 Starting motor 12.3.1 Specifications. 12.3.2 Characteristics, 12.3.3 Structure 12.3.4 Whring diameter of a starting motor. 12.4 Alternator standard, 12V/60A 12.4.1 Specifications. 12.4.2 Structure 12.4.3 Wiring diagram. 12.4.4 Standard output characteristics 12.4.5 Inspection. 42.5 Alternator 12V/80A (Optional) 12.5.1 Specifications. 12.5.2 Structure 12.5.3 ring diagram. 12.5.4 Standard output characteristics 126 Instrument panel 12.6.1 B-type instrument panel (Optional) 12.7 Warning devices 170 170 1m 1m 172 174 175 176 176 177 v7 7 7 179 181 182 183 183 184 185 186 186 186 187 188 189 189 190 191 191 192 193 193, 194 195 195 196 196 197 12.7.4 Oil pressure alarm. 12.7.2 Cooling water temperature alarm... 12.8 Glow plug 412.9 Electric engine stopping device 13. Service standards 13.1 Engine tuning 13.2 Engine body 13.2.1 Cylinder head. 13.2.2 Camshaft and geartrain 13.2.3 Cylinder block 13.3 Lubricating oil system (Trochoid pump) 14, Tightening torque for bolts and nuts 14.1 Main bolt and nut 14.2 Standard bolts and nuts (without lube oil) 197 198 199 200 201 201 202 202 203 204 207 208 208 208 FOR SAFETY 1. SAFETY LABELS + Most accidents are caused by negligence of basic safety rules and precautions. For accident prevention, it is important to avoid such causes before development to accidents. Please read this manual carefully before starting repair or maintenance to fully understand safety precautions and appropriate inspection and maintenance procedures, Attempting at a repair or maintenance job without sufficient knowledge may cause an unexpected accident. + It is impossible to cover every possible danger in repair or maintenance in the manual. Sufficient consideration for safety is required in addition to the matters marked Especially for safety precautions in a repair or maintenance job not described in this manual, receive instructions from a knowledgeable leader. + Safety marks used in this manual and their meanings are as follows: DANGER. indicates an imminent hazardous situation which, if not avoided, WILL result in death or serious injury. rye a33 WARNING. indicates a potentially hazardous situation which, if CTE ot avoided, COULD result in death or serious injury CAUTION. indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. 4 CAUTION + NOTICE - indicates that if not observed, the product performance or quality may not be guaranteed. 2. Safety Precautions (1) SERVICE AREA 4 WARNING e= A CAUTION 4A CAUTION 4 CAUTION 4 CAUTION + Sufficient Ventilation Inhalation of exhaust fumes and dust particles may be hazardous to ones health. Running engines welding, sanding, painting, and polishing tasks should be only done in well ventilated areas. + Safe / Adequate Work Area ‘The service area should be clean, spacious, level and free from holes in the floor, to prevent "slip" or “trip and fall’ type accidents, + Clean, orderly arranged place No dust, mud, oil or parts should be left on the floor surface. [Failure to Observe] An unexpected accident may be caused. + Bright, Safely Illuminated Area ‘The work area should be well it or illuminated in a safe manner. For work in enclosed or dark areas, a “drop cord” should be utilized. The drop cord must have a wire cage to prevent bulb breakage and possible ignition of flammable substances. + Safety Equipment Fire extinguisher(s), first aid kit and eye wash / shower station should be close at hand (or easily accessible) in case of an emergency. (2) WORK - WEAR (GARMENTS) 4 CAUTION ij Ye) (3) TOOLS 4 WARNING 4 WARNING Z| +a + Safe Work Clothing Appropriate safety wear (gloves, special shoes/boots, eye/ear protection, head gear, hamess’, clothing, etc.) should be used/iwom to match the task at hand. Avoid wearing jewelry, unbuttoned cuffs, ties or loose fitting clothes around moving machinery. A serious accident may occur if caught in moving/rotating machinery. + Appropriate Lifting / Holding ‘When fing an engine, use only a lifting device (crane, jack, etc.) with sufficient lifting capacity. Do not overload the device. Use only a chain, cable, or lifting strap as an attaching device, Do not use rope, serious injury may result To hold or support an engine, secure the engine to a support stand, test bed or test cart designed to carry the weight of the engine. Do not overload this device, serious injury may result Never run an engine without being properly secured to an engine support stand, test bed or test cart, serious injury may result + Appropriate Tools Always use tools that are designed for the task at hand, Incorrect usage of tools may result in damage to the engine and or serious personal injury. (4) GENUINE PARTS and MATERIALS A CAUTION = + Genuine Parts Always use genuine YANMAR parts or YANMAR recommended parts and goods. Damage to the engine, shortened engine life and or personal injury may result. (5) FASTENER TORQUE (6) Electrical 4 WARNING si 4 WARNING ee 4 WARNING [® + Torquing Fasteners Always follow the torque values and procedures as designated in the service manual. Incorrect values, procedures and or tools may cause damage to the engine and or personal injury + Short Circuits Always disconnect the (-) Negative battery cable before working on the electrical system. An accidental "short circuit” may cause damage, fire and or personal injury. Remember to connect the (-) Negative battery cable (back onto the battery) LAST + Charging Batteries Charging wet celled batteries produces hydrogen gas. Hydrogen gas is extremely explosive. Keep sparks, open flame and any other form of ignition away. Explosion may occur causing severe personal injury. + Battery Electrolyte Batteries contain sulfuric acid. Do NOT allow it to come in contact with clothing, skin and or eyes, severe bums will result. (7) WASTE MANAGEMENT Observe the following instructions with regard to hazardous waste disposal. Negligence of these will have a serious impact on environmental pollution concerns. 1) Waste fluids such as lube oil, fuel and coolant shall be carefully put into separate sealed containers and disposed of properly. 2) Do NOT dispose of waste materials irresponsibly by dumping them into the sewer, overland or into natural waterways, 3) Waste materials such as oil, fuel, coolant, solvents, fiter elements and batteries, must be disposed of properly according to local ordinances. Consult the local authorities or reclamation facility, (8) FURTHER PRECAUTIONS 4 WARNING bhi 4 WARNING SEs asnlliihiin, pale 4 WARNING 4 WARNING 2 A CAUTION + Fueling / Refueling Keep sparks, open flames or any other form of ignition (match, cigarette, etc.) away when fueling/refueling the unit. Fire and or an explosion may result + Hot Surfaces. Do NOT touch the engine (or any of its components) during running or shorlly after shutting it down, Scalding / serious burns may result. Allow the engine to cool down before attempting to approach the unit. + Rotating Parts Be careful around moving/rotating parts. Loose clothing, jewelry, ties or tools may become entangled causing damage to the engine and or severe personal injury. + Preventing burns from scalding 1) Never open the filler cap shortly after shutting the engine down. Steam and hot water will spurt out and seriously bum you. Allow the engine to cool down before attempt to open the filler cap, 2) Securely tighten the filler cap after checking the cooling water. ‘Steam can spurt out during engine running, if tightening loose + Safety Label Check Pay attention to the product safety label AA safety label (caution plate) is affixed on the product for calling special attention to safety. If itis missing or illegible, always affix a new one. Ri 3. Precautions for Service Work (1) Precautions for Safety Read the safety precautions given at the beginning of this manual carefully and always mind safety in work (2) Preparation for Service Work Preparation is necessary for accurate, efficient service work. Check the customer ledger file for the history of the engine. + Preceding service date + Period/operation hours afier preceding service + Problems and actions in preceding service + Replacement parts expected to be required for service Recording formicheck sheet required for service (3) Preparation before Disassembly + Prepare general tools, special service tools, measuring instruments, oil, grease, non-reusable parts, and parts expected to be required for replacement. + When disassembling complicated portions, put match-marks and other marks at places not adversely affecting the function for easy reassembly. (4) Precautions in Disassembly + Each time a parts is removed, check the part installed state, deformation, damage, roughening, surface defect, etc + Arrange the removed paris orderly with clear distinction between those to be replaced and those to be used again. + Parts to be used again shall be washed and cleaned sufficiently + Select especially clean locations and use clean tools for disassembly of hydraulic units such as the fuel injection pump. (5) Precautions for Inspection and Measurement Inspect and measure parts to be used again as required to determine whether they are reusable or not. (6) Precautions for Reassembly + Reassemble correct parts in correct order according to the specified standards (tightening torques, and adjustment standards). Apply oil important bolts and nuts before tightening when specified. + Always use genuine parts for replacement. + Always use new oil seals, O-rings, packing and cotter pins. + Apply sealant to packing depending on the place where they are used. Apply of grease to sliding contact portions, and apply grease to oil seal lips. (7) Precautions for Adjustment and Check Use measuring instruments for adjustment to the specified service standards. 1. General 1. General 1.1 Exterior views Operating Side Intake silencer Intake manifold Oil filer cap Fuel fiter Fuel injection pump Dipstick Oil filer cap Fuel feed pump Lubricating oi iter Marine gear Non-Operating Side Engine name plate (on the rocker arm cover) Fresh water filer cap Coolant tank / Heat exchanger Exhaust manifold Starter motor Seawater pump V-belt Atternator This illustration shows the 3YM30 with Yanmar marine gear (Model:KM2P-1), ARI 1. General 1.2 Specifications [Official engine model name | _unit 3YM30 ‘3¥M20 [Company internal modelname | — 3YM30 3¥M30C 3y¥Mi20 3YM206 Marine gear model : KM2P-1 ‘3020 KM2P-4 3020 Use : Pleasure use Type 7 Vertical water cooled 4 cycle diesel engine [Combustion system 5 Indirect injection Air charging 7 Naturally aspirated C : 3 Bore xstroke mm(inch)| 76x82 (2.99 x 3.23) 70x74 276x291) Displacement L 1.116 0.854 Continuous Cutout a ) | KIMGHPY 20.1(27.3) 3489 14.7(20.0) / 3489 lpower Engine speea | min" (at Fuel temp. 25°C) * (at Fuel temp. 25°C) * ayy 22.180) 13600 16.2(22) 13600 eta ty | RHPY (at Fuel temp. 25°C) * (at Fuel temp. 25°C) * gansnanty ay | min! 21.3(29.0) / 3600, 15.3(20.8) / 3600 Fuel stop mtn (at Fuel temp. 40°C) (at Fuel temp. 40°C) “* power output at 21.4(29.1) 73600 15.7(21.3)/ 9600 ip flor shart/| CHP) {at Fuel temp. 25°C) * (at Fuel temp. 25°C) * roped sha Tit 20-728-1)/ 2600 14.820.) 2600 gine

    You might also like