Job Safety Analysis (JSA) CORING

JOB SAFETY ANALYSIS (JSA)

JSA Number: 009 Date:

Activity Owner: Site H2S Specialist JSA prepared by:

Task / Operation: Coring

(Specify the task being analysed)

NOTE: RB = Risk Rating before controls implemented - RA = Risk Rating after controls are implemented
Person Responsible
Tasks Hazards RB Hazard Control Measures RA
for Controls
List the tasks required to Against each task list the hazards List the control measures required to
perform the activity in the that could cause injury when the eliminate or minimise the risk of injury
sequence they are carried out task is performed. arising from the identified hazard.
1. Consult with client rep to obtain job Meet with responsible personnel to discuss the
Not being aware of H2S concentrations or any Site H2S Specialist
scope and conduct location/hazard M details of equipment logistics and to pre-plan the L
ammonia treatments
assessment task at hand

2. Dress with necessary PPE as Improper PPE according to standards & job Site H2S Specialist
L Dress according to safety policies of the work site L
required requirement

3. Proceed to do the safety equipment

rig in and to adhere to all safe work Conduct safety meeting prior to job commencement
Having improper or inadequate equipment to Site H2S Specialist
policies and procedures as set out in H ensuring all personnel are aware of the safety M/L
perform the job safely
the safework agreement or company equipment locations and functions
orientation

4. Mask up with SABA or SCBA

While any personnel are performing the tasks
whenever checking for H2S in
requiring the use of breathing apparatus, the safety Site H2S Specialist
collars, drill pipe, core barrel and H2S, pressure M L
rep will be in an upwind safe area with an SCBA unit
whenever requested to do an
on and a gas detection device ready
ammonia treatment

Document Number Created by: Approved by: Issue Date:

CorpForm-109 QHSE Department General Manager August-2014
Page 1 of 2
 Job Safety Analysis (JSA) CORING

Severity
Insignificant Significant Severe Major Catastrophic
Almost Certain/
Medium High High High High

Frequency of the task being

done plus task with higher
High frequency

probability of an event
Probable/
Medium Medium High High High
Likelihood
Frequent

happening
Possible/
Daily
Low Medium Medium High High
Unlikely/
Weekly
Low Low Medium Medium High
Rare Low Low Low Medium High

High Pressure Noise Pinch Points Ignition Source

Fittings not Tightened Over filling of cylinders Machinery Chemical Atmosphere

Potential Hazards

In correct system isolation Confined Space SCBA/SABA Component Failure Falls

Re-fill line valves not closed Lifting In correct pressure rated hose Environment/Weather

Cylinder valves not open Hazardous Atmosphere H.P. Line damage Slips/trip

Pre air intake filter not positioned correctly Buffing & Grinding Depressurizing Chemical Exposure

Overhead Fire Explosion Limited access & egress In correct Job Task Procedures

Other operations in area Communication SCBA/SABA Component Failure Air Quality

Fittings not operational In correct pressure rated fittings used Missing Person Routine mask work

PPE Daily equipment inspections Safety relief valves operational H2S BOP training completed

Communication Rescue Drills & training Equipment inspections executed as per company SOP Compressor turned off

Permit to Work Lifting pre-check visual and MSDS & TDG documentation Bleed off line secured
Hazard Controls

Company SOP on-site current color code & certification Lanyard & harness All connections double checked

Equipment function tested Safety barricade Auto shut down operational SCBA/SABA

Air Analysis current ERP in place and tested Life vest Safety meeting held prior to critical job task

H.P. Lines secure Gas detector tube device Radio/phone access Face shield

Correct H.P. Valve placement for isolation Head count control measures in place Respirator Containment bottles

Electronic gas monitors Safety glasses Hard Hat Safety Shoes

Hearing Protection Rubber gloves Goggles Fire Extinguisher/blanket

Document Number Created by: Approved by: Issue Date:

CorpForm-109 QHSE Department General Manager August-2014
Page 2 of 2