WoodManor Playhouse

Plans

The Queen Anne

WoodManor Playhouses
6341 W. 1600 N.
Corinne, Ut 84307
www.woodmanor.net
colby@woodmanor.net
 Queen Anne Plan Instructions

1. After leveling ground, build base with pressure treated 4 x 4’s and 2 x 4’s. You may also place the playhouse
on a concrete pad using pressure treated 2 x 4’s as a base. The cutout list calls for 4 x 4 x 12’s which are shorter
than the 153” pieces that you need. You will use the leftover pieces from the 129” pieces and splice them to
the other two twelve footers to make the 153” pieces. (see page 1)

2. Build the main floor using sixteen penny nails. ( see page 2)

3. Install ¾” plywood to floor panels nailing every six inches with staples or eight penny nails. (see page 2)

4. Cut notches in floor. These are to accommodate porch roof uprights. Connect studs to the floor with 3”
screws. Put a bead of silicone under these studs. (see page 3)

5. Familiarize yourself with the wall layout. Cut out all exterior siding. Illustrations show the interior view of
the siding. (see pages 3-5)

6. Build lower walls. On walls 1, 2, and 3 hold studs up 3 ½” from bottom of siding. On remaining walls hold
studs up 1 ½” from bottom of siding. Studs should be spaced at 24” on center except where otherwise indi-
cated or when placing them flush with door and window cutouts. Connect studs to siding with 1 ½” staples
or four penny nails. Connect wall panels to floor using staples or eight penny nails. Insert stair platform in
its place and secure with staples. Fireplace instructions found on page 13. (see page 6)

7. Build upper floors using sixteen penny nails. (see page 7)

8. Attach upper floors to lower walls by toe-nailing floor to lower wall studs in the corners with 8-penny nails.
Connect the 3 floor pieces by nailing together every 8 inches with sixteen penny nails. Install 7/16” osb (wa-
fer) to upper floors by nailing every six inches with staples or eight penny nails. (see page 8)

9. Install second row of exterior siding.

10. Build and install stairs. Begin with lower stairs. Hold top of lower stairs flush with top of stair platform and
tightly against outer wall. Nail through plywood into stair platform studs with staples or four penny nails.
Secure bottom of stairs by nailing through exterior siding into side of stairs from the outside. Attach 2 x 4 x
86” upright. Notch should fit over upper floor. Secure to upper floor using eight penny nails. Hold upright
tightly against lower stairs and allow stair platform to rest on top of the 2 x 4 x 24” that is connected to the
upright. Using sixteen penny nails connect upright to stair platform. Hold top of upper stairs flush with
upper floor and tightly against outer wall. Nail through plywood into upper floor studs with staples or four
penny nails. Nail through side of stairs into wall studs with sixteen-penny nails. This will create a ¾” space
between stairs and upper floor to accommodate railing slats. (see page 14)

11. Create upper walls by attaching studs to the siding. Illustration shows how this will look from the inside.
Studs should be spaced at 24” on center except where otherwise indicated or when placing them flush with
window cutouts. (see page 9)

12. Connect wall top plates to upper walls by toe-nailing to upper wall studs with eight penny nails. Connect all
pieces together at the corners using sixteen penny nails. (see page 10)

13. Install remaining T-111.

14. Build and install rafters and ridge-boards. Attach rafters by nailing through top plates with sixteen penny
nails. Attach ridge-boards next by nailing rafters to ridge-boards using sixteen penny nails. Attach hip raf-
ters last. These rafters need to be custom cut and fit on-site, therefore there are no drawings of the hip rafters
that are shown in blue. (see pages 10 & 11)

15. Build and install porch roof uprights. Secure bottom of uprights by nailing through floor studs into uprights
using sixteen penny nails. Upright with notch corresponds with notched railing. (see page 12)

16. Build and install porch roof. Bottom of porch roof framing is 73” from the floor. Bottom of porch roof
framing in the door section is 79 3/8” from the floor. Use sixteen-penny nails to connect porch roof to exte-
rior wall nailing into wall studs, then secure the roof to the wall by using 4” carriage bolts. Connect uprights
to porch roof using sixteen penny nails. (see pages 12 &13)

17. Build and install exterior hand rail and railing slats. Connect handrails by pre-drilling holes and using 3”
screws. Top of handrail should be 24” from main floor. Railing slats are made by ripping a 1 x 6 x 27” into
3 pieces that are 1 ¾” wide. You will need 92 rail slats for the porch and the deck. Attach railing slats 3 ½”
apart using 1 ½” finish nails. (see page 12)

18. Install interior railing. Connect handrails by pre-drilling holes and using 3” screws. Top of handrail should
be 22” from second floor. Upper floor railing slats are made by ripping a 1 x 6 x 25” into 3 pieces that are 1
¾” wide. Cut stair rail slats to fit. Attach railing slats 3 ½” apart using 1 ½” finish nails. (see page 15)

19. Install roof sheeting to porch. Nail every six inches using staples or eight-penny nails. (see page 16)

20. Install roof sheeting to playhouse roof. Nail every six inches using staples or eight-penny nails. (see page 17)

21. Build and install corner molds. Corner molds are built by ripping 3 inches off of a 1 x 6. This will give you
one piece that is 3 1/16” wide and a smaller piece that is 2” wide. You then overlap the large side over the
small side and nail them together with finish nails. Construct angled corners per drawing. (see page 13)

22. Install 2x4’s all around outside edges of roof sheeting by nailing every eight inches with staples or eight-pen-
ny nails. These parts need to be custom fitted; therefore there are no cutout instructions for these parts. (see
page 18)

23. Cut and install gingerbread trim using supplied template. Hold trim flush with top of roof sheeting. Nail
to roof 2x4’s using staples or eight-penny nails. Nail all corners together with 1 ½” finish nails. These parts
need to be custom fitted; therefore there are no cutout instructions for these parts. (see page 18

24. Cut and install drip edge. Drip edge is made by ripping 1 x 6 boards into 1 ¼” strips. You will get 4 pieces
from each 1 x 6 board. Hold drip edge flush with top of trim boards and nail every eight inches with 1 ½”
finish nails. These parts need to be custom fitted; therefore there are no cutout instructions for these parts.
(see page 18)

25. Build doors and frames. (see page 19)

26. Attach 3” butt hinges to doors 10” from top and bottom using 1 ⅝” screws. Attach hinged doors to frames
allowing a ¼” gap between top of door and door frame opening.

27. Install doors and door trim. Doors are attached using 3 inch screws. Trim is attached using 1 ½” finish nails.
You will need to shim sides of door. (see page19)
28. Install door knob per manufacturers’ instructions.

29. Build windows that go in doors. After nailing window frame and face together using 1 ½” finish nails, route
the back side ½” deep (shown in blue hatch on drawing) using a ⅜” rabbeting bit. Install grid pieces hold-
ing them flush with window face. Cut plexiglass to fit and install with ¼”” rope and 18 x ⅞” nails. You may
route a decorative edge on the front of the grids. (we use a ½” round over bit) Plexiglass windows are in-
stalled by inserting windows into the openings that have been cut in the siding. Secure windows with 1 ¼”
screws from the inside of the playhouse. Door window is installed by inserting window into the opening and
securing with 1 ½” finish nails through face frame. Install face frame to opposite side in the same manner.
(see page 20)

30. Build and install side light windows using same methods. (see page 21)

31. Build shuttered windows. After nailing window frame and face together using 1 ½” finish nails, route the
bottom of the front side ½” deep (shown in blue hatch on drawing) using a ⅜” rabbeting bit. Install shut-
ters using 3” T-hinges. Attach T-hinges using ½” wood screws. Attach window latches to inside of shutters.
Route top of back side ½” deep (shown in blue hatch on drawing) using a ⅜” rabbeting bit. Cut plexiglass to
fit and install with ¼” rope and 18 x ⅞” nails. (see pages 22 and 23)

32. Install windows. Nail sides bottom and top of window frame to wall framing using eight penny nails. You
will need to shim sides of windows. Nail window face boards to wall using 1 ½” finish nails.

33. Build hexagon window. All angles are 60 degrees. Nail all parts together using 1 ½” finish nails. Route back
side ½” deep (shown in blue hatch on drawing) using a ⅜” rabbeting bit. Cut plexiglass to fit and install with
1/4” rope and 18 x ⅞” nails. Cut opening in siding and install in same manner as other plexiglass windows.
(see page 24)

34. Build swing. (see pages 25 and 26)

35. Install swing by screwing 2 eye hooks into the proper porch roof stud spaced approximately 26 inches apart.
Cut chain to desired length and hang swing.

36. Build bay window. See instructions on pages 27-29. Install windows into bay window frame using 1 ½’ fin-
ish nails. Install entire unit by inserting into opening on wall #1. Secure to wall framing using 3” screws.

37. After installation of shuttered and bay windows install 2 x 4’s to tops and bottoms of windows on the inside
of the playhouse. Secure these pieces by toe-nailing with eight penny nails and stapling or nailing from the
outside. You can then secure face trim of the shuttered windows using 1 ½” finish nails.

38. Build deck using sixteen penny nails. Attach plywood using staples or eight penny nails. Attach deck to
house using four 4 ½” carriage bolts. Set pier blocks and install uprights ensuring that the deck is level and
uprights are plumb. Install railing and rail slats in same manner as porch rail. (see page 30)

39. Install shingles.

 228"

49-3/4" 46-1/4" 36" 48" 48"

93"
107-3/4"

129"

153"

40 degree angle
50 degree angle
Cutout list (gravel): 48"
1) 2 x 4 x 228"
1) 2 x 4 x 48"
1) 2 x 4 x 55 1/4"
1) 2 x 4 x 31 1/2" (long side to short side
of 50 degree angles)
1) 2 x 4 x 64 3/4"
1) 2 x 4 x 61 5/16" (long side to long side 55-1/4" 61-5/16"
of a 50 and 40 degree angle)
1) 4 x 4 x 93"
2) 4 x 4 x 129" 31-1/2"
2) 4 x 4 x 153"
1) 4 x 4 x 107 3/4" 64-3/4"

89"

105-3/4"

125"

149"

Cutout list (concrete):

1) 2 x 4 x 228"
1) 2 x 4 x 48"
1) 2 x 4 x 55 1/4"
1) 2 x 4 x 31 1/2" (long side to short side
of 50 degree angles)
1) 2 x 4 x 64 3/4"
1) 2 x 4 x 61 5/16" (long side to long side
of a 50 and 40 degree angle)
1) 2 x 4 x 89"
2) 2 x 4 x 125" WoodManor Playhouses
2) 2 x 4 x 149"
1) 2 x 4 x 105 3/4" Queen Anne
Page 1
 225"

16"

16" All angles are to be cut at 40 degrees unless otherwise noted

16"

96"

16"

16"
109-1/4"

16"

48" 177"
16"
174-13/16"
36"
161-7/16"
15-3/4"
Cutout list: 158-1/2"
7) 2 x 4 x 225"
1) 2 x 4 x 96"
4-1/4"
1) 2 x 4 x 109 1/4" 55-1/4" 82-3/8" 61-5/16"
1) 2 x 4 x 36"
1) 2 x 4 x 31 1/2" (40 and 50 degree angles)
1) 2 x 4 x 64 3/4" 31-1/2"
1) 2 x 4 x 61 5/16" (40 & 50 degree angles)
64-3/4"
1) 2 x 4 x 177"
1) 2 x 4 x 174 13/16"
1) 2 x 4 x 161 7/16"
1) 2 x 4 x 158 1/2"
1) 2 x 4 x 82 3/8"

36"
48"
64"

96"

84"

Cutout list: 13-1/4"

8) 3/4" plywood 92"
36"

7-1/4" 60" 55-11/16"

55-11/16"

WoodManor Playhouses 31-1/2"

Queen Anne
Page 2
44-3/8" 5-5/8"
20-3/8"
 This notch is cut 1 1/2"
Cutout list: from the side edge.
1) 2 x 4 x 96"
1) 2 x 4 x 31 7/16" long side to long side of a 50 and 40 degree angle 53-1/4"
1) 2 x 4 x 31 7/16"
1) 2 x 4 x 31 7/16" long side to short side of 50 degree angles
1) 2 x 4 x 20 1/2" 36"
2) 2 x 4 x 27 1/2"
2) 2 x 4 x 13"
96"
All notches should be
13" 1 1/2" wide x 3 1/2" deep

22"

27-1/2" 20-1/2"

60"
31-7/16"
31-7/16" 31-7/16"

This notch is cut 2"

36"
from the side edge.

Wall #3
Wall #2

Wall #4

Wall #9
Wall #10
Wall #11

Wall #1 Wall #8
5
l#
W
al

al

Wall #6
l#

W
7

WoodManor Playhouses
Queen Anne
Page 3
 Wall #1 Wall #2 Walls #5,6 and 7

40" 40" 10"

46-13/16"
36"
26"
23-1/2"
16" 12-1/2" 16" 15"
13"

13-1/2"
28-1/2"
48" 14" 48" 48"
22"
10" 12"

24" 24"
48" 48" 48"
34" 14"

48" 96"
31-7/16"

46-13/16" 16"
40"
48"
16" 15"
18-1/2"

24" 14" 48"

40"
26"
14" 26"
15" 53"
48" 77"

19-1/2"

48"

48"

96"
48"

WoodManor Playhouses
Queen Anne
Page 4
96"
Wall #3
 10"

36"
26"
24"
12"

48" 48" 48"

12" 4"
22"

16"
24"
14"
48" 48" 48"

96" 24"
13" 13"
Wall #4 Wall #8 Wall #9

47-1/4" 3-7/16"
12" 23-1/2"
23-3/4"
9" 27-7/16" 51-5/16"
1-1/2"

These pieces go between lower and upper roof

48" 48"

48" 48"

23-1/2" 23-1/2"
Wall #10 Wall #11 WoodManor Playhouses
Queen Anne
Page 5
 Wall #1 Wall #2 Stair platform

28"
32"
21-1/2"

4"
24" Materials list for stair platform:
27-1/2" 2) 2 x 4 x 21 1/2'
3) 2 x 4 x 28"
1) 21 1/2 x 31" plywood piece

Wall #3 Wall #3

32"

35-1/4"
Fireplace instructions
18" found on page 13
24"

Wall #4 Wall #5 Wall #6 Wall #7

Top view
50 degrees

inside 40 degrees inside

Wall #8 Wall #9 Wall #10 Wall #11

3 1/2"
22-7/16" 1 1/2"

62"

Overhang stud 1/2"

Cutout list:
Top view 9) 2 x 4 x 60"
On walls # 1-3 use 60" studs 23) 2 x 4 x 58 1/2" (2 ripped on a 50 degree
spaced 3 1/2" from bottom of siding angle and 3 ripped on a 40 degree angle for
40 degrees On walls 4-11 use 58 1/2" studs walls 5, 7 and 8. See drawings above)
spaced 1 1/2" from bottom of siding 3) 2 x 4 x 24"
inside 3) 2 x 4 x 32" WoodManor Playhouses
2) 2 x 4 x 35 1/4" Queen Anne
2) 2 x 4 x 62" Page 6
 93"

45"
Cutout list upper floor #1:
20"
2) 2 x 4 x 48"
2) 2 x 4 x 93"
2) 2 x 4 x 71 1/2" 48" 48"
1) 2 x 4 x 45" 71-1/2"
1) 2 x 4 x 20" 25"
1) 2 x 4 x 25"

72"
Cutout list upper floor #2:
1) 2 x 4 x 72"
1) 2 x 4 x 96"
1) 2 x 4 x 43 1/2"
1) 2 x 4 x 19 1/2"
5) 2 x 4 x 69" 45"
1) 2 x 4 x 45"
3) 2 x 4 x 21'
69"
19-1/2"
43-1/2"

Cutout list upper floor #3 21"

2) 2 x 4 x 96"
7) 2 x 4 x 69"
1) 2 x 4 x 31 7/16"
2) 2 x 4 x 31 7/16" 40 and 50 degrees 96"
1) 2 x 4 x 68 1/16"
1) 2 x 4 x 42 5/16" 31-7/16"

31-7/16" 42-5/16" 68-1/16" 69"

31-7/16"

96"

WoodManor Playhouses
Queen Anne
*All angles are 40 degrees Page 7
except the front angles on the turret
 48"

Rip 1 1/2" strips for areas 21-1/2"

shown in red
48"
26-1/2"

74-1/2"

Materials list: 48"

5) sheets 7/16" osb (wafer)

52-1/2"

48"

31-7/16" 72"

48"

24" 96"

WoodManor Playhouses
Queen Anne
Page 8
 Use dimensions to
arrive at correct angles. 2"
Red=long side of angle.
Wall #1 Wall #2 Blue=short side of angle
1 1/2"
56"
57-1/2"
51-1/16"
52-9/16"
41" 41"
Side view of
doorway uprights

Wall #3 Materials list:

12) 2 x 4 x 41"
20) 2 x 4 x 65" (2 ripped on a 50 degree
Wall #3 1-3/4" angle and 3 ripped on a 40 degree angle
for walls 5, 7 and 8. See drawings below)
65" 4) 2 x 4 x 53 9/16"
2) 2 x 4 x 53 1/8" (26 1/4 degree angle)
2) 2 x 4 x 43 1/16" (26 1/4 degree angle)
2) 2 x 4 x 57 1/2"
41" 41"

Wall #4 Wall #5 Wall #6 Wall #7

65" 65"

Top view
50 degrees

inside 40 degrees inside

Wall #8 Wall #9

1-9/16"

Wall #10 Wall #11

53-9/16" 26 1/4 degree angle

41"

43-1/16"
Top view 53-1/8"

40 degrees
WoodManor Playhouses
inside Queen Anne
Page 9
24"
1-1/2" 1-1/2"
 Rafter "A" Rafter "B"
Rafters & ridge-boards
25-1/2" 24-3/4" 22-3/4" 0-1/2"

24" 24"

25-1/2" 96" 96" 24"

95-1/4"
Rafter "B" Rafter "A"

24"

23-1/4"

24"

Materials list:
Top of upper wall #9 2) 2 x 4 x 96"
Rafter "B" 1) 2 x 4 x 95 1/4"
1) 2 x 4 x 23 1/4"
see page 11 for rafter quantities
Siding pieces between lower and upper roof

Top plates
120" 70-1/2"

26 1/2 degree angle

3 1/2"
2 3/4"

58"
Enlarged side view
of this 2 x 4 piece
96" 94-1/2"

48"

40 degrees

11-1/2"

118-1/2" 50 degrees

31-3/8" 31-3/8"

31-1/2"

WoodManor Playhouses
Queen Anne
Page 10
 45 degree angle
top and bottom

32-7/8" 32-7/8" 30-3/4"

1-1/2"

1-1/2"

3-7/16"

2 each 4 each
Rafter "A" 2 each Rafter "B"

26 1/4 degree angle top

63 3/4 degree angle bottom
24-1/4"

52-11/16"

26-3/16"

1-1/2"
7 each 1-1/2" 1 each
3-3/16" 3-3/16"

33 1/2 degree angle top

56 1/2 degree angle bottom

42-1/4" 42-1/4"

1-1/2"

3-3/16"

WoodManor Playhouses
8 each 2 each Queen Anne
Page 11
 Cutout list:
1) 2 x 4 x 96"
1) 2 x 4 x 109 3/16"
1) 2 x 4 x 61 1/4" long side of 40 degrees
to long side of 50 degrees
1) 2 x 4 x 35 7/16" long side of 40 degrees
to long side of 50 degrees
1) 2 x 4 x 64 15/16"
1) 2 x 4 x 31 1/2
1) 2 x 4 x 31 3/8" long side to short side of 50 degrees
1) 2 x 4 x 31 1/8" long side to short side of 50 degrees
96"
1) 2 x 4 x 54 3/4"
1) 2 x 4 x 24 1/2" 109-3/16"
1) 2 x 4 x 47"
14) short rafters (see page 13)
47" 3) long rafters (see page 13)

24-1/2"

35-7/16"

31-1/2"

31-1/8"

61-1/4"
54-3/4"

31-3/8"

64-15/16"
3 1/2"

1 1/2" Cutout list:

1) 2 x 4 x 104 11/16"
1) 2 x 4 x 61 1/4" long side of 40 degrees
to long side of 50 degrees
1) 2 x 4 x 61 3/4"
1) 2 x 4 x 31 3/8" long side to short side of 50 degrees
7) 2 X 4 X 71 7/8" (see drawing) 50-1/4"
1 of these This notch is
1 1/2" wide x
1 3/4" deep
71-7/8"
104-11/16"

6 of these This notch is

23-1/4" 1 1/2" wide x
1 3/4" deep

1 1/2"

3 1/2"

61-1/4"

WoodManor Playhouses
31-3/8"
Queen Anne
Page 12
61-3/4"
Porch roof rafters
15 degree angle top and bottom
33-5/8"

58-1/2"

15 each 3 each

24" 12" 16"

Materials list:
4) 2 x 4 x 24" 12"

1) 1 x 6 x 40" (mantel)
1) 38 x 24 plywood piece (use leftover plywood from door)

Corner molds 3"

3"
3"

rip 20 degree angle rip 25 degree angle

2 1/4" Front of turret Side of turret

Cutout list: Cutout list:

4) 110" Cutout list: 1) 73"
WoodManor Playhouses
2) 73" Queen Anne
1) 134" 1) 57" Page 13
1) 24" 2) 57" 1) 24"
 Set mitre saw to
2 x 4 x 86" upright (see page 15) 53 degrees for the
top and 37 degrees
for the bottom

22"
45-1/16"

2-3/4" 25-1/2"

4" 16-1/2"

7-1/2"

nail treads in
from both sides
with three sixteen
penny nails

35-1/16"
60"

16-1/2"

7-1/2"

Cutout list:
2) 2 x 8 x 35 1/16"
2) 2 x 8 x 44 1/2"
2) 2 x 8 x 17 3/4"
3) 2 x 8 x 16 3/16"
1) 11 1/2 x 20 3/4 plywood or wafer piece
1) 11 1/2 x 19 3/16 plywood or wafer piece
2 x 4 x 24" nailed to upright

Side view WoodManor Playhouses

Queen Anne
Page 14
 Top of 86"
upright Stairs Wall stud Stairs

Rail #3
Upper floor #2

Rail #2

Stairs
Stairs

Rail #1 Top of 20 1/2"

20 1/2" uprights
uprights

Rail #5

Rail #4

Rail #6
Vault over entry

Upper floor #1 Upper floor #1

Wall studs

Cutout list:
1) 2 x 4 x 26 1/2" (rail #1) 1 1/2" x 2 3/4" notch on one side)
1) 2 x 4 x 23" (rail #2)
1) 2 x 4 x 23 1/2" (rail #3) (1 1/2" x 3 1/2" notch on one side)
4) 2 x 4 x 20 1/2" (uprights)
2) 2 x 4 x 21 1/2" (rails #4 & 6) (1 1/2" x 3 1/2" notch on one side)
1) 2 x 4 x 48" (rail #5)
1) 2 x 4 x 86" (upright / see page 14)

Space rail slats

3 1/2 inches apart

View of upper stairs View of lower stairs

with wall #2 removed with wall #3 removed

Cutout list:
27) 25" rail slat WoodManor Playhouses
3) 55" rail slat cut to size on angle Queen Anne
3) 58" rail slat cut to size on angle Page 15
 13-15/16"
95-1/4"

Porch roof sheeting

36-1/2" 36-5/16"

32-7/16"
31-1/2"

36-1/2" 36-1/2" 16-3/4"

12-11/16"

61-1/4" 64-15/16"

7-3/4"
31-3/8"

16-3/16"
36-1/2" 36-1/2"

24-1/2"
31-3/8"

47"

61-1/2"

WoodManor Playhouses
Queen Anne
Page 16
 94-1/2" 78"

2 each 11"

89-5/8"
41"

2 each 48"

48-3/16"

30"
68-1/4"

3 each
54"
41-1/4"

2 each
37-1/8"

Center section Deck side section

Turret section
23-1/4" 78" 78"

2 each
This piece notches 43-1/4"
48" 48" over lower roof

5-1/2"

46-1/2" 15"
16-1/2"

8-7/8"
17-9/16"

40-1/4" 39-1/4"

2 each

35" 35-1/16"

WoodManor Playhouses
Queen Anne
Page 17
overlap all peaks
in this manner

Nail all joints with

16-penny nails

Drip edge

Trim board

WoodManor Playhouses
Queen Anne
Page 18
 side view
3/4 pine Window cutout
20"

13" 12"

18"

1/2" a/c plywood

1/2" a/c plywood

54"

21 5/8"

Top view of door frame

20 3/8"

Materials list for main door: 1 3/4"

2) 54 x 20 a/c ply
2) 1 x 3 1/2 x 54 3 1/2"
2) 1 x 3 1/2 x 13
2) 2 x 4 x 55 5/8 (cut per drawing)
1) 2 x 4 x 20 3/8 (cut per drawing) 7/8"
2) 1 x 2 1/4 x 54 5/8 (door trim)
1) 1 x 3 1/2 x 27 (trim top)

Materials list for upper door:

2) 52 x 20 a/c ply
2) 1 x 3 1/2 x 52
2) 1 x 3 1/2 x 13
2) 2 x 4 x 53 5/8 (cut per drawing) WoodManor Playhouses
1) 2 x 4 x 20 3/8 (cut per drawing) Queen Anne
2) 1 x 2 1/4 x 52 5/8 (door trim) Page 19
1) 1 x 3 1/2 x 27 (trim top)
 Front view

Window frame Window face

18" 16-1/2"

10-1/2"

14"
Back view

Window frame= 1 5/8" width

Window face= 1 3/4" width
Grids= 2" width

Grids

16-1/2" 4-7/8"

Materials list for 2 windows:

4) 1 x1 5/8 x 18
4) 1 x1 5/8 x 10 1/2
8) 1 x1 3/4 x 16 1/6
8) 1 x1 3/4 x 14
1) 1 x 2 x 16 1/2 WoodManor Playhouses
4) 1 x 2 x 4 7/8 Queen Anne
Page 20
 Front view

20" 18-1/2"

3-1/2"

7"

Back view
3-1/2"

Materials list for two windows:

4) 1 x 1 3/4 x 20 (frame)
4) 1 x 1 3/4 x 3 1/2 (frame)
4 1 x 1 3/4 x 18 1/2 (face)
4) 1 x 1 3/4 x 7 (face)
2) 1 x 2 x 3 1/2 (grids)
WoodManor Playhouses
Queen Anne
Page 21
Front view 18"

10-1/2"

12-1/4" Route 1/2" deep with

35-3/4" 34-1/4" a 3/8 rabbeting bit

6-5/16"
22-3/4"

12-1/4"

18"

Back view
Route 1/2" deep with
a 3/8 rabbeting bit

Materials list for 4 large windows: Materials list for 7 small windows:
8) 1 x 2 x 35 3/4 (frame) 14) 1 x 2 x 25 3/4 (frame)
8) 1 x 2 x 12 1/4 (frame) 14) 1 x 2 x 12 1/4 (frame)
8) 1 x 1 3/4 x 34 1/4 (face) 14) 1 x 1 3/4 x 24 1/4 (face)
4) 1 x 1 3/4 x 18 (face) 7) 1 x 1 3/4 x 18 (face)
4) 18" scalloped tops (face) 7) 18" scalloped tops (face)
8) 22 3/4" x 6 5/16" plywood shutter 14) 12 3/4" x 6 5/16" plywood shutter
4) 2 x 2 1/2 x 12 1/4 7) 2 x 2 1/2 x 12 1/4

WoodManor Playhouses
Queen Anne
Page 22
 View from inside window
with latch in place

3/4"
11"

6"
2-3/4" 4 3/4"

6-1/2"

1 3/4"

Materials list for 11 windows:

22) 1 x 1 3/4 x 6
11) 1 x 1 1/4 x 11 WoodManor Playhouses
Queen Anne
Page 23
Front view 7-5/8"
6-1/2"

Window frame Window face

Back view

Materials list for one window:

6) 1 x 1 3/4 x 6 1/6"
6) 1 x 1 3/4 x 7 5/8"
1) plexiglass cut to fit

WoodManor Playhouses
Queen Anne
Page 24
 This piece cut from 1 x 6

This piece cut from 1 x 6

This piece cut from 2 x 4

grid scale 1:2

This piece cut from 1 x 6

Materials list:
2 of each part shown
2) 1 x 2 x 14 (armrest support)
8) 1 x 1 3/4 x 14 (seat slats)
WoodManor Playhouses
10) 1 x 1 3/4 x 15 1/2 ( back slats) Queen Anne
Page 25
 Install eye-bolts by threading a nut
all the way on followed by a washer
insert into swing and place a second
washer followed by a nut
1- attach back support to seat support using 1 5/8" screws
2- attach back slats followed by seat slats using 1 1/2" finish nails
3- attach uprights using 1 5/8" screws
4- attach armrest support using 1 1/4" screws
5- attach armrest using 1 1/2" finish nails
6- drill holes and install eyebolts
7- cut chain to desired length and hang swing

Back support

Armrest
5/16 hole drilled
for eye bolts
Armrest support

5/16 hole drilled

for eye bolts Upright

6-3/8"

Seat support

Cut these parts to fit

WoodManor Playhouses
Queen Anne
Page 26
 instructions: 2"
1- cut 4 x 4's per these dimensions
2- cut plywood to these dimensions
3- attach 4 x 4's to plywood using staples or 8-penny nails

45.00°

18" 34"

2"

2"
10"

2" 2"

2-1/8"

1-1/16"
0-11/16"

2-1/2"

2"
0-3/4" 2-1/2"
Materials list:
4) 4 x 4 x 33
2) 34 x 10 plywood pieces WoodManor Playhouses
Queen Anne
Page 27
 materials list:
2) 2 x 4 x 14
4) 2 x 4 x 7 3/16 cut to fit
plywood for roof

18 x 12 plywood

14" 7 3/16"

26"

Instructions:
1- connect 2 x 4 pieces to plywood using staples or 8 penny nails
2- pre-drill 2 x 4's and screw on an angle into 4 x 4's using 3' screws
3- insert windows and secure using 1 1/2" finish nails
WoodManor Playhouses
4- install bay window Queen Anne
5- roof bay window Page 28
 16"
12-1/2"

26" 24-1/2"

5-7/8"

24-1/2"

Materials list for 1 large window: Materials list for 2 small windows:
2) 1 x 1 3/4 x 26" (frame) 4) 1 x 1 3/4 x 26" (frame)
2) 1 x 1 3/4 x 12 1/2" (frame) 4) 1 x 1 3/4 x 5 5/8" (frame)
2) 1 x 1 3/4 x 24 1/2" (face) 4) 1 x 1 3/4 x 24 1/2" (face)
2) 1 x 1 3/4 x 16" (face) 4) 1 x 1 3/4 x 9 1/8"" (face)
1) 1 x 2 x 24 1/2" (grid) 6) 1 x 2 x 5 5/8" (grid)
6) 1 x 2 x 5 7/8" (grid)

WoodManor Playhouses
Queen Anne
Page 29
 92"
92"

Playhouse wall

48" 48"
Plywood for deck
(top view)
89"
Cut each hole
1 1/2" from edge Cut each hole
1 1/2" x 3 1/2"

Top of deck floor must be

flush with interior floor Ten foot 2x4's run through
holes cut in flooring
(cut off at 24" high)
24"

92"

Outside 2x4's fit under

deck framing

Pier blocks

Materials list:
Railing detail viewed from above 2) 2 x 4 x 48" (deck framing)
4) 2 x 4 x 89" (deck framing)
2) 2 x 4 x 24" 3 1/2" x 1 1/2" notch on one side (uprights)
24" uprights 2) 2 x 4 x 46 1/2" (rails)
(rails resting in notch) 1) 2 x 4 x 92" (rail)
2) 2 x 4 x 10' (deck uprights. Cut to fit after install)
2 2 x 4 x 8' (deck uprights. Cut to fit after install)

46-1/2"
Top of 2x4 uprights
that are running through
holes cut in flooring

92"
WoodManor Playhouses
Queen Anne
Page 30
 Door & window
trim tops
page 1

Cut out trim template

and tape together.
Door & window
trim tops
page 2

27"
 18
2.65"

Door & window

2.68" trim tops
page 3
Cut out trim template
and tape pieces together.

Trim template
page 1
Trim template
page 2
1-1/2"

Trim template
page 3

3"
 7"

5-1/2"
Trim template
page 4
 This piece

This piece cut

Materials list: WoodManor Playhouses

2 of each part shown Swing Parts Templates
Page 1
cut from 1 x 6

from 1 x 6

Materials list: WoodManor Playhouses

2 of each part shown Swing Parts Templates

Page 2
 This piece

This piece cut

Materials list: 2) 1 x 2 x 14 (armrest support)

8) 1 x 1 3/4 x 14 (seat slats)
2 of each part shown 10) 1 x 1 3/4 x 15 1/2 ( back slats)

WoodManor Playhouses
Swing Parts Templates
Page 3
cut from 2 x 4

from 1 x 6

Materials list:
2 of each part shown

WoodManor Playhouses
Swing Parts Templates
Page 4
 Materials List
Quantity Description For what part
180 2x4x8 Floors / walls etc.
10 2 x 4 x 10 Main floor / porch rof / railing / deck uprights
4 2 x 4 x 16 Main floor
7 2 x 4 x 20 Main floor
3 2x8x8 Stairs
2 4x4x8 Bay window
1 4 x 4 x 8 pressure treated Gravel foundation
1 4 x 4 x 10 pressure treated Gravel foundation
4 4 x 4 x 12 pressure treated Gravel foundation
4 2 x 4 x 8 pressure treated Gravel foundation
1 2 x 4 x 20 pressure treated Gravel foundation
9 3/4" cdx plywood Floor sheeting / deck sheeting
2 1/2" ac plywood Door / stair landing / fireplace
21 4 x 8 sheet T1-11 4" O/C of exterior siding Exterior siding
18 7/16" osb Roof sheeting / upper floor sheeting
40 1 x 6 x 12 Trim, rail slats, windows, swing, door
2 Plexiglass size 30 x 60 Windows
1 Keyed knob Door
1 Bed & bath knob Door
4 square Shingles Roof
4 3" butt hinges Door
22 3" t-hinges Shuttered windows
20’ 3/16” chain Swing
4 5/16” x 4” eye bolt Swing
2 3/8” x 4 1/2” lag screw hook Swing
22 5/16” hex nut Swing
22 5/16” washer Swing
2 Pier blocks Deck
4 5/16” x 4” carriage bolts Deck / porch roof
2 tubes Silicone Floor studs
100’ 1/4” cotton rope Windows
1 small box 18 x 7/8” finish nails Windows
5 lbs. 16d nails
5 lbs. 8d nails
5 lbs. 4d nails
2 lbs. 1 1/2" finish nails
2 lbs. 1 1/4" screws
2 lbs. 3" screws