1 1

2
3 Abaqus 3DEXPERIENCE R2016x Date 22-Aug-2018
Time 19:17:35
4 For use by Supplied by Team-SolidSQUAD under license from Dassault Systemes or
its subsidiary.
5
6
7
8 STEP 1 INCREMENT 1 STEP TIME 0.00
9
10
11 S T E P 1 S T A T I C A N A L Y S I S
12
13
14

15
16 AUTOMATIC TIME CONTROL WITH -
17 A SUGGESTED INITIAL TIME INCREMENT OF 1.00
18 AND A TOTAL TIME PERIOD OF 1.00
19 THE MINIMUM TIME INCREMENT ALLOWED IS 1.000E-05
20 THE MAXIMUM TIME INCREMENT ALLOWED IS 1.00
21
22 LINEAR EQUATION SOLVER TYPE DIRECT SPARSE
23
24 CONVERGENCE TOLERANCE PARAMETERS FOR FORCE
25 CRITERION FOR RESIDUAL FORCE FOR A NONLINEAR PROBLEM 5.000E-03
26 CRITERION FOR DISP. CORRECTION IN A NONLINEAR PROBLEM 1.000E-02
27 INITIAL VALUE OF TIME AVERAGE FORCE 1.000E-02
28 AVERAGE FORCE IS TIME AVERAGE FORCE
29 ALTERNATE CRIT. FOR RESIDUAL FORCE FOR A NONLINEAR PROBLEM 2.000E-02
30 CRITERION FOR ZERO FORCE RELATIVE TO TIME AVRG. FORCE 1.000E-05
31 CRITERION FOR RESIDUAL FORCE WHEN THERE IS ZERO FLUX 1.000E-05
32 CRITERION FOR DISP. CORRECTION WHEN THERE IS ZERO FLUX 1.000E-03
33 CRITERION FOR RESIDUAL FORCE FOR A LINEAR INCREMENT 1.000E-08
34 FIELD CONVERSION RATIO 1.00
35 CRITERION FOR ZERO FORCE REL. TO TIME AVRG. MAX. FORCE 1.000E-05
36 CRITERION FOR ZERO DISP. RELATIVE TO CHARACTERISTIC LENGTH 1.000E-08
37
38 VOLUMETRIC STRAIN COMPATIBILITY TOLERANCE FOR HYBRID SOLIDS 1.000E-05
39 AXIAL STRAIN COMPATIBILITY TOLERANCE FOR HYBRID BEAMS 1.000E-05
40 TRANS. SHEAR STRAIN COMPATIBILITY TOLERANCE FOR HYBRID BEAMS 1.000E-05
41 SOFT CONTACT CONSTRAINT COMPATIBILITY TOLERANCE FOR P>P0 5.000E-03
42 SOFT CONTACT CONSTRAINT COMPATIBILITY TOLERANCE FOR P=0.0 0.100
43 CONTACT FORCE ERROR TOLERANCE FOR CONVERT SDI=YES 1.00
44 DISPLACEMENT COMPATIBILITY TOLERANCE FOR DCOUP ELEMENTS 1.000E-05
45 ROTATION COMPATIBILITY TOLERANCE FOR DCOUP ELEMENTS 1.000E-05
46
47 EQUILIBRIUM WILL BE CHECKED FOR SEVERE DISCONTINUITY ITERATIONS
48
49 TIME INCREMENTATION CONTROL PARAMETERS:
50 FIRST EQUILIBRIUM ITERATION FOR CONSECUTIVE DIVERGENCE CHECK 4
51 EQUILIBRIUM ITERATION AT WHICH LOG. CONVERGENCE RATE CHECK BEGINS 8
52 EQUILIBRIUM ITERATION AFTER WHICH ALTERNATE RESIDUAL IS USED 9
53 MAXIMUM EQUILIBRIUM ITERATIONS ALLOWED 16
54 EQUILIBRIUM ITERATION COUNT FOR CUT-BACK IN NEXT INCREMENT 10
55 MAXIMUM EQUILIB. ITERS IN TWO INCREMENTS FOR TIME INCREMENT INCREASE 4
56 MAXIMUM ITERATIONS FOR SEVERE DISCONTINUITIES 50
57 MAXIMUM CUT-BACKS ALLOWED IN AN INCREMENT 5
58 MAXIMUM DISCON. ITERS IN TWO INCREMENTS FOR TIME INCREMENT INCREASE 50
59 MAXIMUM CONTACT AUGMENTATIONS FOR *SURFACE BEHAVIOR,AUGMENTED LAGRANGE 50
60 CUT-BACK FACTOR AFTER DIVERGENCE 0.2500
61 CUT-BACK FACTOR FOR TOO SLOW CONVERGENCE 0.5000
62 CUT-BACK FACTOR AFTER TOO MANY EQUILIBRIUM ITERATIONS 0.7500
63 CUT-BACK FACTOR AFTER TOO MANY SEVERE DISCONTINUITY ITERATIONS 0.2500
64 CUT-BACK FACTOR AFTER PROBLEMS IN ELEMENT ASSEMBLY 0.2500
65 INCREASE FACTOR AFTER TWO INCREMENTS THAT CONVERGE QUICKLY 1.500
66 MAX. TIME INCREMENT INCREASE FACTOR ALLOWED 1.500
67 MAX. TIME INCREMENT INCREASE FACTOR ALLOWED (DYNAMICS) 1.250
68 MAX. TIME INCREMENT INCREASE FACTOR ALLOWED (DIFFUSION) 2.000
69 MINIMUM TIME INCREMENT RATIO FOR EXTRAPOLATION TO OCCUR 0.1000
70 MAX. RATIO OF TIME INCREMENT TO STABILITY LIMIT 1.000
71 FRACTION OF STABILITY LIMIT FOR NEW TIME INCREMENT 0.9500
72 TIME INCREMENT INCREASE FACTOR BEFORE A TIME POINT 1.000
73
74 CONTACT CONTROLS APPLIED TO ALL CONTACT PAIRS:
75 GLOBAL STABILIZATION CONTROL IS NOT USED
76 RELATIVE PENETRATION TOLERANCE FOR AUGMENTED LAGRANGE CONTACT:
77 FINITE-SLIDING SURFACE-TO-SURFACE 5.000E-02
78 OTHERWISE 1.000E-03
79
80 PRINT OF INCREMENT NUMBER, TIME, ETC., EVERY 1 INCREMENTS
81
82 THE MAXIMUM NUMBER OF INCREMENTS IN THIS STEP IS 100
83
84 LINEAR EXTRAPOLATION WILL BE USED
85
86 CHARACTERISTIC ELEMENT LENGTH 2.500E-02
87
88 DETAILS REGARDING ACTUAL SOLUTION WAVEFRONT REQUESTED
89
90 DETAILED OUTPUT OF DIAGNOSTICS TO DATABASE REQUESTED
91
92 PRINT OF INCREMENT NUMBER, TIME, ETC., TO THE MESSAGE FILE EVERY 1
INCREMENTS
93
94 COLLECTING MODEL CONSTRAINT INFORMATION FOR OVERCONSTRAINT CHECKS
95
96 COLLECTING STEP CONSTRAINT INFORMATION FOR OVERCONSTRAINT CHECKS
97
98
99 INCREMENT 1 STARTS. ATTEMPT NUMBER 1, TIME INCREMENT 1.00
100
101 NUMBER OF EQUATIONS = 3690 NUMBER OF FLOATING PT. OPERATIONS = 1.42E+08
102
103 CHECK POINT START OF SOLVER
104
105 CHECK POINT END OF SOLVER
106
107 ELAPSED USER TIME (SEC) = 0.10000
108 ELAPSED SYSTEM TIME (SEC) = 0.10000
109 ELAPSED TOTAL CPU TIME (SEC) = 0.20000
110 ELAPSED WALLCLOCK TIME (SEC) = 0
111
112 CONVERGENCE CHECKS FOR EQUILIBRIUM ITERATION 1
113
114 MAX. PENETRATION ERROR 16.6052E-15 AT NODE PART-1-1.607 OF CONTACT PAIR
115 (ASSEMBLY_S_SURF-3,ASSEMBLY_M_SURF-3)
116 MAX. CONTACT FORCE ERROR 42.3569E-06 AT NODE PART-1-1.127 OF CONTACT PAIR
117 (ASSEMBLY_S_SURF-3,ASSEMBLY_M_SURF-3)
118 THE CONTACT CONSTRAINTS HAVE CONVERGED.
119
120 AVERAGE FORCE 6.32 TIME AVG. FORCE 6.32
121 LARGEST RESIDUAL FORCE 1.751E-03 AT NODE 373 DOF 3
122 INSTANCE:
PART-1-1
123 LARGEST INCREMENT OF DISP. -2.001E-05 AT NODE 613 DOF 2
124 INSTANCE:
PART-1-2
125 LARGEST CORRECTION TO DISP. -2.001E-05 AT NODE 613 DOF 2
126 INSTANCE:
PART-1-2
127 ESTIMATE OF DISP. CORRECTION 1.401E-09
128 FORCE EQUILIB. ACCEPTED BASED ON SMALL RESIDUAL AND ESTIMATED CORRECTION
129
130 ITERATION SUMMARY FOR THE INCREMENT: 1 TOTAL ITERATIONS, OF WHICH
131 0 ARE SEVERE DISCONTINUITY ITERATIONS AND 1 ARE EQUILIBRIUM ITERATIONS.
132
133 TIME INCREMENT COMPLETED 1.00 , FRACTION OF STEP COMPLETED 1.00
134 STEP TIME COMPLETED 1.00 , TOTAL TIME COMPLETED 1.00
135
136
137 THE ANALYSIS HAS BEEN COMPLETED
138
139
140
141 ANALYSIS SUMMARY:
142 TOTAL OF 1 INCREMENTS
143 0 CUTBACKS IN AUTOMATIC INCREMENTATION
144 1 ITERATIONS INCLUDING CONTACT ITERATIONS IF PRESENT
145 1 PASSES THROUGH THE EQUATION SOLVER OF WHICH
146 1 INVOLVE MATRIX DECOMPOSITION, INCLUDING
147 0 DECOMPOSITION(S) OF THE MASS MATRIX
148 1 REORDERING OF EQUATIONS TO MINIMIZE WAVEFRONT
149 0 ADDITIONAL RESIDUAL EVALUATIONS FOR LINE SEARCHES
150 0 ADDITIONAL OPERATOR EVALUATIONS FOR LINE SEARCHES
151 1 WARNING MESSAGES DURING USER INPUT PROCESSING
152 0 WARNING MESSAGES DURING ANALYSIS
153 0 ANALYSIS WARNINGS ARE NUMERICAL PROBLEM MESSAGES
154 0 ANALYSIS WARNINGS ARE NEGATIVE EIGENVALUE MESSAGES
155 0 ERROR MESSAGES
156
157
158
159 JOB TIME SUMMARY
160 USER TIME (SEC) = 0.80000
161 SYSTEM TIME (SEC) = 0.10000
162 TOTAL CPU TIME (SEC) = 0.90000
163 WALLCLOCK TIME (SEC) = 1
164