Question #1

A storage administrator has requested a recommendation on upgrading their VNX5600 to a

comparable Unity storage array. The solution requires a maximum capacity of 3.5 PB.
To meet the administrator's requirement without over provisioning the capacity, which Unity Hybrid
storage array is recommended?
A. Unity 300
B. Unity 400
C. Unity 500
D. Unity 600

Question #2
What is the minimum VMware Hypervisor version a server must be running in order to support the
deployment of a UnityVSA system?
A. 4.0
B. 5.0
C. 5.5
D. 6.0

Question #3
Which feature is supported on a UnityVSA operating environment?
A. Asynchronous Replication
B. MCC Write Caching
C. Quick Start Pool Provisioning
D. Data at Rest Encryption

Question #4
A storage administrator is creating a host profile in Unisphere to provide host access to block storage
resources using the iSCSI protocol. The host initiators were not automatically discovered and must
be manually added.
In addition to the SAN host IQN, what other configuration can be performed through the "Create
iSCSI Initiator Wizard" window?
A. Enable and disable CHAP settings
B. Create Mutual CHAP secret
C. Create Global CHAP secret
D. Enter CHAP username and secret

Question #5
A storage administrator is configuring a storage pool on a Unity system containing Flash disks and
SAS disks. What tier will the system assign to each of the disk types?
A. Flash: Extreme Performance SAS: Performance
B. Flash: Performance SAS: Capacity
C. Flash: Extreme Performance SAS: Capacity
D. Flash: Capacity SAS: Performance

Question #6

What describes the LUN Snapshot Copy operation?

A. Parent cannot be a snapshot copy Can only copy a detached snapshot Has an independent
Retention Policy from the parent
B. Parent can be a snapshot copy Can only copy a detached snapshot Has an independent Retention
Policy from the parent

C. Parent can be a snapshot copy Can copy an attached or detached snapshot Inherits the parent
Snapshot Retention Policy

D. Parent cannot be a snapshot copy Can copy an attached or detached snapshot Inherits the parent
Snapshot Retention Policy

Question #7

Which technology is used by Unity Snapshots?

A. Copy on First Write

B. Inline Deduplication

C. Redirect on Write

D. Block Compression

Question #8

DRAG DROP - What is the correct sequence of steps taken by the storage array when an AC power
failure is detected?

Select and Place:

Question #9

A system administrator is configuring asynchronous remote replication for an existing NAS server
and its' file systems on a Unity system. What should the administrator create to ensure all data is
replicated for the NAS server and the file system?

A. Replication sessions on each file system only

B. Replication sessions for each file system first and then the NAS server

C. A replication session on the NAS server and then manually create replication sessions on each file
system
D. A replication session for only the NAS server

Question #10

Which Unity feature provides a high bandwidth connection for large file transfers, enables proactive
Service Request generation and usage license reporting, and operates on a 24x7 basis?

A. EMC Service Center

B. Software Licensing Central

C. Unisphere Central

D. EMC Secure Remote Services

Question #11

Which software bundles are provided with the Unity Starter software package?

A. FAST Cache and Fast VP

B. Thin Provisioning and Quality of Service

C. Controller-Based Encryption and RecoverPoint Basic

D. FAST Cache and Local Point-in-Time Copies

Question #12

When configuring asynchronous remote replication, how many internal Unity Snapshots are
configured and utilized on the source system by a single replication session?

A. 1

B. 2

C. 3

D. 4

Question #13

A storage administrator is implementing FAST Cache on a Unity 500 storage array and can select
from a mix of SSD drives. Which drive types can be configured to meet the administrator's
requirements?

A. 200 GB and 400 GB

B. 400GB and 1.6 TB

C. 1.6 TB and 3.2 TB

D. 3.2 TB and 800 GB

Question #14

A storage administrator is required to test a new version of an application loaded on a secondary

host. The administrator must use existing data contained on a

LUN provisioned from Unity to a primary host.

Which solution will meet the requirement and provide space efficiency?

A. Create a snapshot of the LUN Configure LUN access for the secondary host Attach the snapshot to
the secondary host

B. Create a snapshot of the LUN Configure snapshot access to the LUN for the secondary host Attach
the snapshot to the secondary host

C. Create a Synchronous Replication session for the LUN Configure access to the replica LUN for the
secondary host Attach the secondary host

D. Create an Asynchronous Replication on session for the LUN Configure access to the replica LUN
for the secondary host Attach the secondary host

Question #15

On which systems is Quality of Service available?

A. Physical Unity systems only

B. UnityVSA systems only

C. Physical Unity and UnityVSA systems

D. All Flash Unity systems only

Question #16

When deploying virtual disks for a UnityVSA system, what is an EMC recommended Disk Provision
Policy?

A. Thick Provision Eager Zeroed

B. Thin Provision

C. Thick Provision

D. Thick Provision Lazy Zeroed

Question #17

Which UnityVSA user interface allows advanced users to create scripts for automating routine tasks?
A. Unisphere Central

B. UEMCLI

C. SP Console

D. Unisphere GUI

Question #18

A system administrator has configured a system using the Initial Configuration wizard. After
completing the wizard, the administrator discovers that an incorrect

IP address has been assigned to the Unity system.

How can the IP address be changed?

A. The IP address cannot be changed once it has been configured

B. Through the Service interface using the ifconfig command

C. In the Unisphere Settings menu

D. The IP address can only be changed using the UEMCLI

Question #19

Which FAST Cache operation can be performed from the Settings window?

A. Disable FAST Cache use on a specific pool

B. Pause FAST Cache use

C. Expand FAST Cache

D. Enable FAST Cache use on a specific pool

Question #20

Which Unity service task is used to reinstall the root operating system while leaving the user's data
intact?

A. Restore the Management server

B. Reimage the Storage Processor

C. Restore the Management software

D. Reinitialize the storage system

Question #21

What is the maximum number of LUNs in a Consistency Group?

A. 25

B. 50

C. 75

D. 100

Question #22

Which migration tool can be used to move file data a Unity storage array in both NFS and CIFS/SMB
protocols?

A. EMC Select Datadobi

B. Unity Async Replication

C. rsync

D. EMCopy

Question #23

Which step must be completed prior to performing the initial configuration of a UnityVSA system
and creating the first storage pool?

A. Create an ESXi host profile

B. License the system for NFS and SMB support

C. Add vDisks to the storage appliance

D. Install license keys for thin provisioning

Question #24

What is the minimum and maximum recovery point objectives (RPO) configurable when using Unity
native asynchronous replication?

A. Minimum= 5 minutes Maximum= 24 hours

B. Minimum= 5 minutes Maximum= 48 hours

C. Minimum= 1 minute Maximum= 24 hours

D. Minimum= 1 minute Maximum= 48 hours

Question #25

A system administrator has added a new Unity storage array to their environment. The
administrator wants to migrate block data from vVNX running in their
VMware environment to a UnityVSA. In addition, the administrator needs to migrate the block data
from an older CLARiiON storage array to the new Unity storage array.

Which single block migration option will work for both the virtual and hardware storage devices?

A. SAN Copy Push

B. VPLEX

C. Host-Based LVM

D. RecoverPoint

Question #26

How is encryption set for a Unity storage system?

A. Clicking the "Mode" checkbox on the Manage Encryption page

B. Selecting "Status" on the Manage Encryption page

C. Automatically set at the factory

D. First time the license is applied

Question #27

A system administrator experienced a power failure in their environment. To which device will cache
de-stage?

A. M.2 SSD on each Storage Processor

B. First four disks in the Disk Processor Enclosure

C. Cache does not need to de-stage as it is now non-volatile

D. Backup Battery Unit will keep the data alive in cache

Question #28

A service provider is installing a Unity storage system for an end-user. The end-user is concerned
about network security and will not allow the service provider access to the network.

How can the service provider set a static IP address for the Unity storage system management
interface?

A. Use the embedded InitCLI tool

B. Connect directly to the service ports and configure the networking through UEMCLI

C. Use an IPMI serial over LAN connection

D. Use the Connection Utility to create a configuration file

Question #29

Which task must be performed on the storage system in order to access a file system read/write
snapshot?

A. Configure Host Access to the LUN snapshots

B. Configure the NFS/SMB share to the file system snapshot

C. Connect to the NFS/SMB share of the snapshot

D. Perform the snapshot "Attach to Host" operation

Question #30

Which severity level alerts for a fault condition that has occurred, has minor impact on the system,
and does not need to be fixed immediately?

A. Critical

B. Notice

C. Error

D. Warning

Question #31

A storage administrator wants to configure a Unity system to log system events to a remote log
server. In order to allow access to the log server, which port should the administrator ensure is not
blocked by the firewall?

A. 514

B. 714

C. 1000

D. 5179

Question #32

A Unity system LUN has a daily snapshot schedule with a Retention Policy of seven days. A hardware
failure results in a double fault of the LUN.

Which snapshot behavior will be experienced?

A. All of the snapshots will be unavailable to restore data from

B. Data restoration is available from the oldest snapshot, all others are unavailable

C. All of the snapshots will be available to restore data from

D. Data restoration is available from the newest snapshot, all others are unavailable
Question #33

What describes multiple LUN snapshots?

A. Captures multiple point-in-time data states. Snapshot data state is marked "unmodified" from its
source when attached. Snapshot tree supports multiple simultaneous attaches.

B. Captures multiple point-in-time data states. Snapshot data state is marked "unmodified" from its
source when attached. Snapshot tree supports only one attach at a time.

C. Captures multiple point-in-time data states. Snapshot data state is marked "modified" from its
source when attached. Snapshot tree supports multiple simultaneous attaches.

D. Captures multiple point-in-time data states. Snapshot data state is marked "modified" from its
source when attached. Snapshot tree supports only one attach at a time.

Question #34

What is the maximum number of LUN snapshots that are supported by Unity?

A. 16

B. 96

C. 256

D. 512

Question #35

At which stage in the Unity power up sequence would the Storage Processor enter Service mode
upon detecting an error?

A. After the CMI is started

B. Bootflash

C. POST

D. BIOS

Question #36

An administrator's Unity system is configured with both a Fibre Channel CNA and a Fibre Channel I/O
module. Which Fibre Channel port on each SP must be used for native synchronous replication?

A. CNA FC port 5

B. I/O module FC port 2

C. CNA FC port 4

D. I/O module FC port 5

Question #37

Which feature provides the ability to provision block and file storage for Microsoft Windows or
Microsoft SharePoint sites?

A. EMS Storage Integrator for Windows

B. Array Offloaded Data Transfer

C. vStorage APIs for Array Integration

D. EMC Virtual Storage Integrator

Question #38

Which information must be retrieved and used to select the unconfigured UnityVSA system when
running the Auto-discover option of the Connection Utility?

A. Array Name

B. System's Serial ID

C. DNS Host Name

D. System's UUID

Question #39

What is an advantage for selecting Centralized ESRS over Integrated ESRS?

A. External virtual machine is not required

B. WAN compression is not required to Unity systems

C. CHAP security is not required between Unity systems

D. Internet connectivity is not required for every Unity system

Question #40

In UnityVSA, what is the maximum storage capacity offered by the VVOLs license?

A. 4TB

B. 10TB

C. 25TB

D. 50TB
Question #41

A system administrator receives a warning that their DPE I/O Module has a fault. In this situation,
which type of replacement is required?

A. Hot-pluggable CRU

B. Non-Hot-pluggable FRU

C. Hot-pluggable FRU

D. Non-Hot-pluggable CRU

Question #42

Which UnityVSA storage resource can be configured with Host I/O limits?

A. NAS Server

B. Pool

C. File System

D. LUN

Question #43

Which option can be enabled in the Advanced tab of the SMB Share Properties window?

A. Shared VHDX

B. Controller-Based Encryption

C. SMB Direct

D. Protocol Encryption

Question #44

Which UnityVSA configuration can be performed using the Unisphere Initial Configuration wizard?

A. Register host iSCSI initiators

B. Configure Link Aggregation

C. Register host HBA WWNs

D. Add iSCSI network interfaces

Question #45

A system administrator wants to configure asynchronous replication on their Unity system. What is
required before creating a replication session?
A. A Fibre Channel connection configured between the remote systems. A configured replication
connection between the remote systems.

B. A Sync Replication Management Port configured on each system. A Fibre Channel connection
configured between the remote systems. A configured replication connection between the remote
systems.

C. An IP-based replication interface on the same network as the destination system's replication
interface. A configured replication connection between the remote systems.

D. A Sync Replication Management Port configured on each system. An IP-based replication interface
on the same network as the destination system's interface. A configured replication connection
between the remote systems.

Question #46

How long before a license expires will UnityVSA send the first alert warning?

A. 3 days

B. 7 days

C. 15 days

D. 1 month

Question #47

What is the minimum memory requirement for a host running VMware ESXi 6.0 to support the
deployment of a UnityVSA system?

A. 8 GB

B. 12 GB

C. 16 GB

D. 18 GB

Question #48

A storage administrator wants to create a series of daily snapshots for an existing critical LUN. How
can the snapshots be created?

A. Snapshot schedules can only be configured within the LUN Creation wizard

B. From the Pool Properties page, configure the Snapshot schedule

C. Only manually taken snapshots are supported on existing LUNs

D. From the LUN Properties page, configure the Snapshot schedule

Question #49

Which operation can be performed from the FAST VP settings section in the Unisphere Settings
window?

A. Enable scheduled data relocation at the pool level

B. Exclude pool from the data relocation schedule

C. Enable scheduled data relocation at the system level

D. View the data relocation progress between tiers

Question #50

Through which protocols are backend storage provisioned to the ESXi host when deploying a
UnityVSA system?

A. iSCSI, SMB, and NFS

B. iSCSI and NFS only

C. FC, iSCSI, and NFS

D. FC and iSCSI only

Question #51

Where do the D@RE encryption/decryption functions occur in the Unity storage system?

A. Host I/O Modules

B. Storage Processor Cache

C. SAS I/O Module

D. Self-encrypting drives

Question #52

Based on the exhibit, which port can provide either Fibre Channel or Ethernet connectivity for host
access?

A. A

B. B

C. C
D. D

Question #53

A system administrator is browsing their local management station for a Unity license file. Which file
extension is used for Unity license files?

A. .lic

B. .rsa

C. .lin

D. .cer

Question #54

A storage administrator wants to add as asynchronous replication session to a pair of Unity systems
with an existing synchronous replication session that is operating correctly. Which configuration
steps are needed?

A. Create Replication interfaces on both systems. Modify the Replication Connection Mode. Run a
Replication Connection Verify and Update operation.

B. Create Replication Interfaces on the source system. Modify the Mode for Replication Connection.
Perform a manual Sync operation on the Asynchronous session.

C. Create Replication Interfaces on destination system. Establish FC connectivity using the

Synchronous FC Ports of each system. Perform a manual Sync operation on the Asynchronous
session.

D. Create Replication Interfaces on both systems. Establish FC connectivity using the Synchronous FC
Ports of each system. Run a Verify and Update operation for the Replication Connection

Question #55

Which Unity feature benefits oracle OLTP environments by improving storage utilization?

A. 4 block formatting

B. Increased SP Cache size

C. Automatic storage tiering

D. VVOLS
Question #56

A system administrator has installed the Unity Connection Utility on a Microsoft Windows host. The
Windows host is connected to the same physical subnet as a newly installed Unity storage system.
When the utility is run, it does not discover any Unity storage systems.

What should be checked on the host that may be preventing the utility from discovering any Unity
storage systems?

A. Java SE version

B. Ethernet adapter flow control

C. Network Access Filter Driver

D. Host firewall services

Question #57

A Unity 400 system has Data at Rest Encryption licensed and enabled. Which operation(s) must be
performed from the Unisphere Settings window to ensure the system is still operational after SP
replacements?

A. Download Audit Log

B. Download Checksum

C. Backup Keystore File

D. Download Audit Log and Checksum

Question #58

When a storage resource has a snapshot taken of it, where are writes to the storage resource
written?

A. New space allocated from the storage resource parent pool

B. New space allocated in 256 MB stripes from FAST Cache

C. Existing space of the storage resource

D. Existing space from the Reserves LUN Pool

Question #59

When the LUN Snapshot Attach to Host operation is performed, what does the Unity system
optionally do before beginning the attach process?

A. Creates a snapshot of the LUN

B. Detaches the host from the snapshots of any other LUN

C. Creates a copy of the snapshot

D. Deletes all other existing snapshots of the LUN

Question #60

Which Directory Services can be configured in the Unisphere Settings window?

A. LDAP

B. NIS

C. NDS

D. Active Directory

Question #61

A Unity storage system is installed with 10 Gb optical SFPs in CNA ports 4 and 5 of both Storage
Processors. The storage administrator has had a request from a user to connect to the storage
system through Fibre Channel.

How can the administrator reconfigure the CNA ports for 16Gb Fibre Channel SFPs?

A. Configure all CNA ports for 16Gb Fibre Channel

B. Configure CNA port 4 of SPA and SPB as 10Gb optical Configure CNA port 5 of SPA and SPB as 16
Gb Fibre Channel

C. Configure CNA port 4 and 5 of SPA as 10 Gb optical Configure CNA ports 4 and 5 of SPB as 16 Gb
Fibre Channel

D. CNA ports cannot be reconfigured once they are committed

Question #62

In UnityVSA, which license(s) is able to extend the storage capacity from 25 TB to 50 TB with an
upgrade path license?

A. Professional only

B. Professional and VVOLS

C. VVOLS only

D. Community

Question #63

When defining which resources on the destination system the replicated item will use for an
asynchronous session, which settings must be provided?
A. Replication Mode, RPO, and Replicate To

B. Name, Pool, and Storage Provisioning

C. Ethernet Port, Subnet/Prefix Length, and Gateway

D. Management IP Address, User Name, and Password

Question #64

What is one method that is used to verify an ESRS configuration?

A. Proxy server authentication

B. RSA authentication

C. Trigger an SNMP trap test

D. Send an e-mail verification

Question #65

A file system is 1 TB in size and contains 250 GB of data. The file system is not fully allocated and
only 450 GB of pool storage is in use. The user wants to reduce the file system to 300 GB.

How much space is returned to the storage pool?

A. 150 GB

B. 450 GB

C. 700 GB

D. 750 GB

Question #66

In order to replace a faulty component, a service provider has placed one of the Unity Storage
Processors into Service mode. Once the component is replaced, how is the Storage Processor
brought back into Normal mode?

A. Exit the Service Mode task

B. Reboot the Storage Processor

C. Reboot the storage system

D. Restart the Management software

Question #67

A user is having difficulty troubleshooting a Unity storage system and the service provider has been
contacted for assistance. The service provider needs to run some service commands on the Storage
Processors to troubleshoot the issue further.

Which step must be taken to allow the service provider remote access to the storage system?

A. Enable SSH on the storage system

B. Set the Unisphere preferences to "Optimize" for remote access

C. Specify the SMTP configuration

D. Specify the Remote Logging configurationѝ

Question #68

How long will a Copy Back operation take when a hot spare is invoked?

A. Pro-Active hot spare does not use a Copy Back operation

B. Copy Back time depends on the RAID type

C. Copy Back time depends on the disk capacity

D. Copy Back time depends on the disk type

Question #69

A storage administrator wants to configure a Unity system to join the list of arrays remotely
monitored for activity and system status using Unisphere Central. The security policy on the
Unisphere server was set to "automatic".

What additional security information must be specified in the Unisphere Settings window to enable
communication with Unisphere Central?

A. Unisphere Central IP address and login credentials

B. Unisphere Central IP address and Central Hash

C. Unisphere Central Hash and login credentials

D. Unisphere Central Hash and challenge phrase

Question #70

A storage administrator has purchased a UnityVSA and asks your recommendation on how to
provision the storage to their ESXi host. Based on Dell EMC best practices, what should you
recommend?

A. Thick Provisioned
B. Thick Provision Eager Zeroed

C. Thin Provisioned

D. Thin Provisioned Eager Zeroed

Question #71

According to Dell EMC best practices, how should off-site data be asynchronously replicated for a DR
solution?

A. Include a Flash tier in a hybrid pool where asynchronous replication will be active on the source
only.

B. Include a Flash tier in a hybrid pool where asynchronous replication will be active on both the
source and destination.

C. Configure the RLP on both the source and destination arrays equal to 20% of the data to be
replicated

D. Configure the sync replication ports on the CAN for 16Gb Fibre Channel on both the source and
destination.

Question #72

What is used by the Local LUN Move data mobility feature?

A. Transparent Data Transfer

B. SANCopy push

C. Inband Migration Tool

D. Common base Snapshots

Question #73

A company has a Unity 300 system with 200 SAS drives. They need to increase the number of SAS
drives by 300. Which in-place upgrade is required?

A. Unity 400F

B. Unity 400

C. Unity 600F

D. Unity 500

Question #74

What are characteristics of the LUN Snapshot Copy operation?

A. Parent cannot be a snapshot copy Can only copy a detached snapshot Has an independent
Retention Policy from the parent

B. Parent can be a snapshot copy Can only copy a detached snapshot Has an independent Retention
Policy from the parent

C. Parent can be a snapshot copy Can copy an attached or detached snapshot Inherits the parent
Snapshot Retention Policy

D. Parent cannot be a snapshot copy Can copy an attached or detached snapshot Inherits the parent
Snapshot Retention Policy

Question #75

When can Data at Rest Encryption (D@RE) be enabled?

A. License is applied the first time

B. Management IP is assigned

C. LUN is created

D. File system is created

Question #76

What is the sequence of steps that must be executed to implement IP Multi-tenancy in a Unity
system?

A. Create file systems and shares for each tenant Configure host access for the tenant's shares Add
tenants to the Unity System

B. Associate tenants with existing NAS servers Create file systems and shares for each tenant
Configure host access for the tenant's shares

C. Create a NAS server for each tenant Create file systems and shares for each tenant Add tenants
and associate to the NAS servers

D. Add tenants to the Unity system Create a NAS server for each tenant Create file systems and
shares for each tenant

Question #77

If each Storage Processor in a Unity storage array has two on-board CNA ports with a dual
personality controller, which protocols are supported by these CNA ports?

A. Fibre Channel at 2/4/8/16 Gb/s and iSCSI at 10 Gb/s.

B. Fibre Channel at 4/8/16 Gb/s and iSCSI at 10 Gb/s.

C. Fibre Channel at 4/8/16 Gb/s and FICON at 8 Gb/s.

D. FCoE at 10 Gb/s and iSCSI at 10 Gb/s

Question #78

A storage administrator is considering adding another application to run on their Unity 300 but they
are concerned about the application's performance. They ask what is considered "normal" for CPU
utilization. Based on Dell EMC best practices, what should be your response?

A. Below 50%

B. 50% - 70%

C. 70% - 90%

D. 90% - 95%

Question #79

Based on Dell EMC based practices, under what conditions would you consider creating multiple
pools on a Unity 500?

A. Separate resources for multi-tenancy Create larger failure domains

B. Combine pools where FAST Cache is and is not active Consolidate resources for multi-tenancy

C. Dedicate resources to meet specific performance goals Separate resources for multi-tenancy

D. Combine pools where FAST Cache is and is not active Dedicate resources to meet specific
performance goals

Question #80

When a copy of a file system snapshot is created, what are the characteristics of the copy?

A. Read/write, shareable to clients

B. Read-only, accessed by clients through the CVFS mechanism

C. Read-only, shareable to clients

D. Read/write, accesses by clients through the CVFS mechanism

Question #81

Which operation can be performed on the General tab of the LUN Properties page?

A. Extend the LUN

B. Grant Host access

C. Replicate the LUN

D. Set Host I/O limits

Question #82

Which Unity system configuration can be performed using the Unisphere Initial Configuration
wizard?

A. Register host iSCSI initiators

B. Configure Link Aggregation

C. Add iSCSI network interfaces

D. Register host HBA WWNs

Question #83

Which system level alert indicates an error has occurred that has no impact on the system and
should be remedied in the near future?

A. Error

B. Warning

C. Informational

D. Notice

Question #84

What is the maximum number of file system snapshots that are supported by Unity?

A. 16

B. 96

C. 256

D. 512

Question #85

Under what conditions should fully provisioned storage be recommended?

A. Storage objects subject to snapshots

B. Workloads requiring high throughput

C. Workloads requiring high bandwidth

D. Storage objects subject to replication

Question #86

A system administrator plans to shut down a Unity storage system for routine maintenance. What
should be done to prevent data loss before shutting down the storage system?

A. Detach all active snapshots from hosts.

B. Manually disable the storage system write cache

C. Disconnect provisioned storage from hosts.

D. Toggle both Storage Processors into Service mode

Question #87

A storage administrator wants to asynchronously replicate a compressed LUN from the primary site
to a Unity at the secondary site. Which statement describes this operation?

A. Replication of compresses data is controlled by the bandwidth throttle setting.

B. By default, replication compresses data sent to the destination.

C. The source data is uncompressed, then replicated to the destination.

D. The source data is replicated to the destination, then uncompressed.

Question #88

What is the maximum recovery point objectives (RPOs) configurable when using Unity native
asynchronous replication?

A. Minimum = 1 minute Maximum = 60 minutes

B. Minimum = 1 minute Maximum = 1440 minutes

C. Minimum = 5 minutes Maximum = 60 minutes

D. Minimum = 5 minutes Maximum = 1440 minutes

Question #89

What is a characteristic of Automatic UFS64 File System extension?

A. Array I/O service to clients is disrupted during auto-extension

B. Allocated space remains unchanged after extend operation

C. Auto-extension can exceed the file system visible size

D. File system cannot auto-extend past the provisioned size

Question #90

How is a Local LUN Move configured?

A. First select the LUN, then select the Pool to move the LUN into, and finally choose the Move
operation.

B. First select the Pool to move the LUN into, then choose the Move operation, and finally select a
LUN.

C. First choose the Move operation, then select a LUN, and finally select the Pool to move the LUN
into.

D. First select a LUN, then choose the Move operation, and finally select the Pool to move the LUN
into

Question #91

Which storage access configuration is unique to VMware Datastores?

A. Host IO burst policy

B. vCenter Server

C. IP Multi-tenancy

D. Auto formatting

Question #92

An administrator is preparing to configure logging to a remote host. If they use the Unity default
values, which port needs to be open for the system to transfer the log information?

A. 443

B. 514

C. 546

D. 8443

Question #93

What functionality is provided by the Unity UFS64 Enterprise File System architecture?

A. File systems scaled up to 16 TB.

B. QoS controlled by density-based policies.

C. Up to 64,000 sub-directories per directory

D. Space reclamation of unused blocks.

Question #94

On which platform(s) is FAST Cache available?

A. All Flash Unity systems only

B. Physical Unity systems only

C. Unity hybrid systems only

D. Physical and UnityVSA systems

Question #95

A system administrator wants to grant privileges to manage storage resources and host
configurations for some users. However, the administrator wants to ensure users have no privileges
to manage user accounts, change network settings and NAS servers, or perform software upgrades.
Which user role should be associated with the user accounts to be created?

A. Administrator

B. Operator

C. Storage Administrator

D. Service

Question #96

A Unity customer has a 20 TB pool consisting of SAS and NL-SAS drives. Based on Dell EMC best
practices, what is the minimum recommended amount of Flash capacity they should use for a Flash
tier?

A. 1 TB

B. 2 TB

C. 4 TB

D. 10 TB

Question #97

What can be used by advanced users to create scripts for automating routine Unity tasks?

A. Unisphere GUI

B. Unisphere CLI commands

C. CloudIQ

D. UEMCLI commands
Question #98

You have recently deployed a UnityVSA system. In addition to the three virtual disks on which the
system is deployed, what is the minimum number of virtual disks required to create a storage pool
on the system?

A. 1

B. 2

C. 4

D. 5

Question #99

Which component is required for compression to work?

A. FAST Cache

B. PFDC

C. Thick LUN

D. FAST VP

Question #100

In UnityVSA, what is the maximum storage capacity offered by the Professional license?

A. 4 TB

B. 10 TB

C. 25 TB

D. 50 TB

Question #101

Which feature can be configured for a Unity File System NFS share?

A. Continuous Availability

B. Offline Availability

C. Host Access Level

D. Protocol Encryption
Question #102

A Unity storage system is installed with 10Gb optical SFPs in CNA ports 4 and 5 of both Storage
Processors. The storage administrator receives from a user to connect to the storage system through
Fibre Channel.

How can the administrator address the request?

A. Configure all CNA ports for 16Gb Fibre Channel

B. Configure CNA port 4 of SPA and SPB as 10Gb optical Configure CNA port 5 of SPA and SPB as 16
Gb Fibre Channel

C. Configure CNA port 4 and 5 of SPA as 10 Gb copper Configure CNA ports 4 and 5 of SPB as 16 Gb
Fibre Channel

D. Once committed, CNA ports cannot be reconfigured without data loss.

Question #103

What describes the Cutover operation for a File Import session?

A. Client access to data is switched to the target Unity system and the session can be rolled back if
Canceled.

B. Production data access is from Unity but the clients still connect to the interface of the VNX.

C. Production data access is permanently set on Unity and the original data is deleted from VNX.

D. Client access to data is switched to the target Unity system and the session cannot be rolled back
or Canceled.

Question #104

What is a connectivity rule for hosts that connect to multiple Unity systems?

A. Must connect to all arrays using a single protocol.

B. Can connect to different arrays with different protocols.

C. CNA connections used with alternating protocols.

D. iSCSI is required to connect a host to multiple arrays.

Question #105

A storage administrator wants to configure a Unity system to join the list of arrays remotely
monitored for activity and system status using Unisphere Central. The security policy on the
Unisphere server is set to "automatic". What additional security information must be specified in the
Unisphere Settings window to enable communication with Unisphere Central?

A. Unisphere Central Hash and login credentials

B. Unisphere Central Hash and challenge phrase

C. Unisphere Central IP address and Central Hash

D. Unisphere Central IP address and login credentials.

Question #106

What is the function of the File Import data mobility feature?

A. Imports NFSv3 configured NAS Server with its associated file systems from one Unity system to
another.

B. Provides mobility of NFSv3 datastores between Unity systems for ESXi host disaster recovery

C. Provides disaster recovery, replicating a VNX VDM and its file systems to a remote Unity system.

D. Migrates NFSv3 configured VDM with its associated file systems from a VNX system to a Unity
system.

Question #107

What is an advantage of using the InitCLI tool to assign an IP address to a Unity storage system?

A. Allows additional services beyond what the Connection Utility offers.

B. Supports an IPv6 configuration.

C. Supports the configuration of DHCP addresses.

D. Does not require the host to have Java installed.

Question #108

What is required for file system creation on Unity?

A. Shares

B. DNS configuration

C. NTP configuration

D. NAS Server
Question #109

What functionality is provided to Unity from its integration with CTA?

A. DHSM data mobility to cloud destination on Virtustream

B. Synchronous disaster recovery solution for Unity file storage

C. Data migration solution for VNX block storage to Unity

D. Unity configured as a destination for tiered DHSM data

Question #110

A system administrator has asynchronous remote replication configured between a pair of systems
and replication is currently operating normally. When the administrator views a replication session
on the Unisphere Sessions page for the destination system, which option is available when viewing
"More Actions"?

A. Failover with sync

B. Failover

C. Pause

D. Sync

Question #111

When the LUN Snapshot Restore operation is performed, what does the Unity system automatically
do before beginning the restoration process?

A. Detaches the hosts from the snapshot

B. Creates a copy of the snapshot

C. Detaches the host from the LUN

D. Creates a snapshot of the LUN

Question #112

A system administrator has placed the Storage Processor (SP) in Service Mode for maintenance.
Using Unisphere, they notice the mode field for the SP still displays both SPs as normal.

What is another indicator the administrator can check to verify that the SP is in Service mode?

A. SP Fault LED is solid blue

B. Unsafe to remove LED is lit

C. SP Fault LED blinks alternating amber and blue

D. DPE Chassis Fault LED is solid amber

Question #113

A storage administrator notices that all the configured Host I/O Limit policies are Globally Paused.
How can the administrator put these policies into the Active state?

A. Select the Host I/O Limit policy for each and configure the Host I/O Limits setting to Active.

B. From the Settings>Performance page, configure the Host I/O Limits settings to Resume.

C. From the Settings> Performance page, configure the Host I/O Limits settings to Active.

D. Select the Host I/O Limit policy for each and configure the Host I/O Limits setting to Resume.

Question #114

Which protocol(s) is used to access VMware VMFS datastores from Unity?

A. Fibre Channel over IP

B. iSCSI and Fibre Channel

C. Fibre Channel only

D. iSCSI only

Question #115

A system administrator is configuring asynchronous remote replication for an existing NAS server
and its associated file systems on a Unity system. What action

(s) will meet the requirements?

A. Manually create replication sessions for each file system. The system will automatically create a
session for the NAS Server.

B. Manually create NAS Server replication session. The system will automatically create sessions for
the associated file systems.

C. Manually create replications for each associated file system. Then manually create a session for
the NAS Server.

D. Manually create NAS Server replication session first. Then manually create replication sessions on
each of the associated file systems.

Question #116

What is the usefulness of setting a quota limit to zero?

A. Increases space efficiency on the file system.

B. Reduces CPU overhead for clients accessing data.

C. Increases file system access performance.

D. Enables tracking and reporting on file system usage.

Question #117

What is a consideration for IP Packet Reflect running on a NAS server?

A. Communications initiated by Unity do not require route table lookups.

B. SP must be rebooted after IP Packet Reflect is disabled.

C. SP Must be rebooted after IP Packet Reflect is enabled.

D. Reply packets are sent via the same interface as the request packets.

Question #118

Where can Unity Compression be enabled?

A. All-Flash systems only

B. All-Flash and 3-tier pools

C. All-Flash pools only

D. Thick LUNs only

Question #119

Which Unity feature supports provisioning within vCenter, provides full visibility to physical storage,
and increases management efficiency?

A. VSI

B. ODX

C. ESI

D. VAAI
Question #120

When creating a NAS Server replication session, which settings are required for the destination NAS
Server?

A. Name, Pool, and Storage Provisioning

B. Interface configuration, Pool, and Storage Processor

C. Pool, RPO, and Storage Processor

D. Name, interface configuration, and RPO

Question #121

What is a consideration when managing Host I/O Limit polices?

A. Only shared Host I/O Limit policies can be paused and resumed

B. All policies are resumed when any single policy is resumed

C. Each policy can be paused or resumed independently.

D. All policies are paused if a single policy is paused.

Question #122

How is encryption set for a Unity storage system?

A. By selecting "Status" on the Manage Encryption page

B. Automatically the first time the license file is applied

C. By clicking the "Mode" checkbox on the Manage Encryption page

D. Programmatically set at the factory.

Question #123

Asynchronous remote replication is configured for a NAS Server and its associated file systems. What
operations can be performed to make data available if the primary site goes down?

A. Failover operation on the NAS Server session, then a Failover operation on each of the file system
sessions

B. Failover with Sync operation on each of the file system sessions, then a Failover with Sync
operation on the NAS Server session.

C. Failover operation on each of the file system session, then a Failover operation on the NAS Server
session.

D. Failover with Sync operation on the NAS Server session, then a Failover with Sync operation on
each of the file system sessions.
Question #124

After performing the initial configuration of a new UnityVSA, when do alerts concerning license
expiration first occur?

A. 7 days prior to expiration

B. 15 days prior to expiration

C. 1 month prior to expiration

D. 2 months prior to expiration

Question #125

What is the significance of setting a soft quota limit?

A. Allows the user the ability to compress the offending data.

B. Prevents UNIX hosts from encountering a stale mount.

C. Required to meet SEC regulatory requirements.

D. Provides a grace period before enforcing the quota limit.

Question #126

What is the maximum storage capacity supported by a Dell EMC UnityVSA with the Community
Edition subscription?

A. 4 TB

B. 10 TB

C. 25 TB

D. 50 TB

Question #127

What is the purpose of a Proxy NAS Server?

A. Increase performance for shared network connections that access NAS Servers

B. Access Snapshot replicas on the destination side of a replicated file resource

C. Access Snapshots for testing production NAS Servers

D. Increase security of production NAS Servers

Question #128

DRAG DROP -

Match each integrated ESRS characteristic with its attribute.

Question #129

What are considerations when configuring a Proxy NAS Server?

A. Can be created on either SP regardless of where the replicated NAS Server resides May utilize
different access protocols as the replicated NAS Server

B. Can be created on either SP regardless of where the replicated NAS Server resides Must use the
same access protocols as the replicated NAS Server

C. Must be created on the same SP as the replicated NAS Server Must use the same access protocols
as the replicated NAS Server

D. Must be created on the same SP as the replicated NAS Server Different access protocols may be
utilized as the replicated NAS Server

Question #130

Which VVol object stores .vmx files, logs, and NVRAM?

A. Config

B. Memory

C. Data

D. Swap
Question #131

What is the correct method to initiate a Dell EMC Unity power down sequence?

A. Use the uemcli halt command

B. Switch both Standby Power Supplies to OFF

C. Execute Shut Down Storage System in Unisphere Service tasks

D. Click the Shut Down button in Unisphere system view

Question #132

A storage administrator is required to test a new version of an application loaded on a secondary

host. The administrator must use existing data contained on a

LUN provisioned from a Dell EMC Unity to a primary host.

Which solution will meet the requirement and provide space efficiency?

A. Create an Asynchronous Replication session for the LUN Configure access to the replica LUN for
the secondary host Attach the secondary host

B. Create a Snapshot of the LUN Configure LUN access for the secondary host Attach the Snapshot to
the secondary host

C. Create a Snapshot of the LUN Configure secondary host connectivity to Dell EMC Unity Attach the
Snapshot to the secondary host

D. Create a Synchronous Replication session for the LUN Configure access to the replica LUN for the
secondary host Attach the secondary host

Question #133

FAST VP tracks data for relocation within the pool at what size slices?

A. 128 MB

B. 256 MB

C. 512 MB

D. 1024 MB

Question #134

The LUN Snapshot Attach to Host operation is being performed with Read/Write Access selected. By
default, what does the Dell EMC Unity system do before beginning the attach process?

A. Detaches the host from the Snapshot of any other LUN

B. Creates a Snapshot of the LUN

C. Detaches existing attached hosts from the LUN Snapshot tree

D. Creates a copy of the Snapshot

Question #135

What is a function of CloudIQ?

A. Tier to cloud storage

B. Provision storage resources

C. Configure host access

D. Monitor system health

Question #136

When can a LUN be defined as thin or thick?

A. Any time after the LUN has been created

B. Only when creating the LUN

C. Only when enabling data reduction on the LUN

D. Only when adding host access to the LUN

Question #137

How is the Dell EMC Unity Data Reduction Ratio calculated?

A. Divide the predate-reduction size of all storage resources and their snapshots by the postdata-
reduction size of all storage resources and their snapshots.

B. Add up the efficiencies gained from thin provisioning, Deduplication, and Compression.

C. Divide the predate-reduction size of all storage resources excluding their snapshots by the
postdata-reduction size of all storage resources excluding their snapshots.

D. Add up the efficiencies gained from thin provisioning, Snapshots, and Compression.

Question #138

Which Dell EMC Unity storage resource allows modification of its block size during creation?

A. VVol file datastore

B. Block datastore

C. VVol block datastore

D. NFS datastore

Question #139

A company needs to expand their dynamic pool by 10 TB. The current dynamic pool consists of sixty-
three 7.6 TB SSD drives that are configured for RAID5 12+1.

What is the minimum number of drives needed for the pool expansion?

A. 1

B. 2

C. 13

D. 15

Question #140

The preferred production interface is active. What does the Dell EMC Unity system do once a NAS
Server starts outbound traffic to an external service?

A. Uses the backup interface

B. Initiates NAS Server failover

C. Uses the active production interface

D. Enables Packet Reflect

Question #141

Which layer of the Dell EMC Unity storage architecture provides access to both the virtual storage
pool and configured LUN resources?

A. Enclosure Services Interface

B. Common software

C. SCSI Enclosure Services

D. Communications Management interface

Question #142

A company plans to add five drives to a 30 drive SAS Flash 4 All-Flash pool on a Dell EMC Unity 600
storage array. Which drive type(s) can be used for the expansion?

A. SAS Flash 2 and SAS Flash 4 only

B. SAS Flash 4 only

C. SAS Flash 3 and SAS Flash 4 only

D. Any SAS Flash drive type

Question #143

What block size do Dell EMC Unity systems use to copy highly accessed blocks of data from spinning
drives into FAST Cache?

A. 16 KB

B. 32 KB

C. 64 KB

D. 128 KB

Question #144

What are four constraints defined in a VMware Capability Profile?

A. Service Level, Access, Protocol, and Space Efficiency

B. Capacity, Drive Type, RAID Level, and Data Reduction

C. Protocol Endpoint, Drive Type, RAID Level, and VM UUID

D. Service Level, Drive Type, RAID Level, and Space Efficiency

Question #145

What component is a hot-pluggable CRU?

A. DPE BBU

B. DPE I/O module

C. 80 drive DAE cooling module

D. 25 drive DPE cooling module

Question #146

Which policy status condition is available for Host I/O Limits?

A. Resuming

B. Disabled

C. Global Paused

D. Error

Question #147

Automatic shrink operations will trigger storage space reclamation on which type of storage
resources?

A. Thick file systems

B. Thick LUNs

C. Thin LUNs

D. Thin file systems

Question #148

A user is setting up Dell EMC Unity network ports for connectivity between the NAS clients and NAS
Servers. In Unisphere, what can a user modify under the

Access section of the Settings configuration window?

A. Speed and MTU only

B. Speed, MTU, and port aggregation

C. Speed, MTU, and name of port

D. Speed and port aggregation only

Question #149

DRAG DROP -

The cache has sent data to the Data Reduction logic during proactive cleaning or flushing. What is
the correct sequence of steps taken by the Data Reduction logic?

Select and Place:

Question #150

The embedded FC ports allow connection at what speeds?

A. 4Gb/s, 8 Gb/s, and 16 Gb/s

B. 10 Gb/s and 16 Gb/s

C. 8 Gb/s and 16 Gb/s only

D. 1 Gb/s and 10 Gb/s

Question #151

Which FAST VP operation can be performed from the System Settings window?

A. Modify data relocation schedule

B. Delete snapshots from the tier

C. Cancel data relocation operations

D. Manually start data relocation

Question #152

Which VASA API protocol is used to integrate with Dell EMC UnityVSA over HTTPS?

A. SNMP

B. WSDL

C. SOAP

D. REST

Question #153

A storage administrator has added multiple resources to a single density-based Host I/O Limit policy
for the following storage resources:

✑ LUN A: 100 GB

✑ LUN B: 100 GB

✑ LUN C: 600 GB

✑ Density-Based Limit 10 IOPS

What is the total IOPS set by this policy?

A. 80

B. 800

C. 810

D. 8,000

Question #154

A High Endurance SSD is limited to how many writes per day?

A. 1

B. 10

C. 25

D. 30
Question #155

Which storage pool object is created for every RAID group in a traditional pool?

A. Stripe Volume

B. Private LUN

C. Pool Slice

D. MetaLUN

Question #156

Which Dell EMC Unity service task is used to reinstall the root operating system while leaving the
existing data intact?

A. Restart the Management Software

B. Restart the Management Server

C. Reinitialize the Storage System

D. Reimage the Storage Processor

Question #157

On a Dell EMC Unity system, all hosts can be required to use which authentication method for iSCSI
interfaces?

A. PAP

B. Kerberos

C. EAP

D. CHAP

Question #158

Which IP connection characteristic is unique to file-based storage access?

A. Link Aggregation

B. VLAN tagging

C. Bandwidth throttle

D. Mirrored writes
Question #159

With Redirect on Write technology, when writes are made to the storage resource and more space is
required, what size is the slice allocated from the parent pool?

A. 8 KB

B. 64 KB

C. 128 MB

D. 256 MB

Question #160

What limitation should be considered when using Local NAS Server Mobility to move NAS Servers?

A. NAS Server's active replication session must be deleted and re-created.

B. A NAS Server that is a File Import destination can be moved.

C. NAS Server Mobility supports two concurrent NAS Server moves.

D. NAS Server Mobility only supports a single NAS Server move at a time.

Question #161

What is the maximum number of Dell EMC Unity arrays that can participate is a Synchronous
Replication topology?

A. 2

B. 4

C. 5

D. 16

Question #162

You are creating a dynamic pool using 12 drives in the Unisphere GUI. Which RAID stripe width will
be set when creating the dynamic pool using RAID 6?

A. 4+2

B. 6+2

C. 8+2

D. 10+2
Question #163

Which FAST Cache operation proactively copies dirty pages to underlying hard disk drives?

A. FAST Cache flushing

B. FAST Cache promotion

C. FAST Cache warming

D. FAST Cache cleaning

Question #164

What is a use case for Thin Clones?

A. Primary production

B. Development and testing

C. Offline backup

D. Data archiving

Question #165

Which Dell EMC Unity model(s) supports the 12 Gb/s SAS I/O module?

A. All Dell EMC Unity models

B. Dell EMC Unity 600/650F only

C. Dell EMC Unity 500/550F and Dell EMC Unity 600/650F only

D. Dell EMC Unity 400/450F, Dell EMC Unity 500/550F, and Dell EMC Unity 600/650F only

Question #166

What is a consideration when attempting to downgrade from Integrated ESRS Two-way to ESRS One-
way?

A. Ensure that port 9443 is open

B. Validate Dell EMC Support Credentials

C. Run readiness check prior to downgrading ESRS

D. Downgrading ESRS is not supported

Question #167

A Thin Clone has just been created. What operation can be performed on it?

A. Change FAST VP Policy

B. Change SP ownership

C. Change Data Reduction setting

D. Increase its size.

Question #168

What is a characteristic of the iSCSI interface on Dell EMC Unity storage arrays?

A. IQN aliases can be created optionally after the iSCSI interface is created.

B. IQN aliases are associated with an iSCSI interface.

C. IQNs are associated with a network port.

D. An iSCSI interface can be created with both an IPv4 and IPv6 IP address.

Question #169

Which feature is only supported on physical Dell EMC Unity systems?

A. Asynchronous Replication

B. Synchronous Replication

C. Host I/O Limits (QoS)

D. VVols

Question #170

Dell EMC Unity systems collect several metrics at various time intervals and use ESRS to send the
information to CloudIQ.

What are those metrics and their time intervals?

A. Alerts = 5 min Performance = 5 min Capacity = 1 hr Configuration = 1 hr

B. Alerts = 2 min Performance = 1 hr Capacity = 1 hour Configuration = 1 hr

C. Alerts = 5 min Performance = 1 hr Capacity = 2 hour Configuration = 1 hr

D. Alerts = 2 min Performance = 30 min Capacity = 1 hr Configuration = 1 hr

Question #171

During the configuration of ESRS, how is the Customer Contact Data verified?

A. Access code sent through email to the customer

B. Step taken during the ESRS Network check

C. Step taken by the ESRS Policy Manager

D. Step taken during the readiness check for ESRS

Question #172

On which storage objects is data Reduction supported?

A. Thick LUNs and VVols

B. VMFS datastores and VVols

C. Thin LUNs and thin VMFS datastores

D. Thin LUNs and thick LUNs

Question #173

A storage administrator is tasked with creating a DR solution for block and file storage resources on a
Dell EMC Unity 650F system at a primary production site.

The company has two other campus locations.

Campus A is located 50 km away and has a Dell EMC Unity 400 Hybrid system. Campus B is located
200 km away and has a Dell EMC UnityVSA system.

What should the storage administrator do to provide the best protection of storage resources while
meeting recommended latency levels?

A. Replicate block storage resources synchronously to Campus A Replicate file storage resources
asynchronously to Campus B

B. Replicate block storage resources synchronously to Campus A Replicate file storage resources
synchronously to Campus A

C. Replicate block storage resources asynchronously to Campus A Replicate file storage resources
synchronously to Campus A

D. Replicate block storage resources asynchronously to Campus B Replicate file storage resources
asynchronously to Campus A
Question #174

What capability is provided by the Dell EMC CIFS Management snap-in?

A. Configure share permissions

B. Configure NAS Server registry settings

C. Manage home directories

D. Manage local NAS Server users

Question #175

DRAG DROP -

What is the correct sequence of steps required to deploy a Dell EMC UnityVSA?

Select and Place:

Question #176

What is the size of a Private LUN slice?

A. 8 KB

B. 64 KB

C. 256 MB

D. 1024 MB

Question #177

A company has the following available drive types in their Dell EMC Unity 500 storage array:

✑ 1.2 TB SAS

✑ 2 TB NL-SAS

100 GB SSD
✑ 1.6 TB SSD

✑ 3.8 TB SSD

What combination of drives can the company use to create a storage pool?

A. 2 TB NL-SAS and 100 GB SSD

B. 1.6 TB SSD and 3.8 TB SSD

C. 1.2 TB SAS and 1.6 TB SSD

D. 2 TB NL-SAS and 3.8 TB SSD

Question #178

A company needs to expand their dynamic pool by 5 TB. The current dynamic pool consists of sixty-
three 3.8 TB SSD that are configured for RAID5 4+1.

What is the minimum number of drives needed for the pool expansion?

A. 1

B. 6

C. 7

D. 8

Question #179

Refer to the exhibit.

Which port is used to connect the DPE to a DAE?

A. A

B. B

C. C

D. D
Question #180

What technology is used by Dell EMC Unity Snapshots?

A. Copy on First Write, which requires a storage resource reserved to hold original data that changed
to preserve the point-in-time view.

B. Redirect on White, which requires no storage resource to create a Snapshot, writes are redirected
on parent pool.

C. Copy on First Write, which requires no storage resource is needed to create a Snapshot, writes are
copied pool.

D. redirect on Write, which requires a storage reserved to hold original data that changed to
preserve the point-in-time view.

Question #181

When a manual snapshot of a file system is created, what items are required for its configuration?

A. Name, Description, and Access Type

B. Retention Policy, Access Type, and Schedule

C. Description, Retention Policy, and Schedule

D. Name, Retention Policy, and Access Type

Question #182

For high availability within iSCSI, connections should be attached using what?

A. Different subnets

B. Flow control

C. Twinax cables

D. Jumbo frames

Question #183

What is a consideration when designing a replication solution using the native Dell EMC Unity
replication feature?

A. Asynchronous remote replication supports replication to up to two remote Dell EMC Unity
systems

B. Synchronous remote replication supports replication to up to two remote Dell EMC Unity systems

C. Synchronous remote replication supports replication to up to one remote Dell EMC Unity systems
D. Asynchronous remote replication supports replication to up to one remote Dell EMC Unity
systems

Question #184

A storage administrator is planning to move a NAS Server to the peer SP on a Dell EMC Unity system.
The NAS Server and two of its associated file systems have active asynchronous replication sessions
to a remote Dell EMC Unity system.

How should the storage administrator proceed?

A. Manually pause the replication sessions for the NAS Server and file systems.

B. Set the RPO value to 1440 for the NAS Server and file system replication sessions

C. Set the RPO value to 0 for the NAS Server and file system replication sessions

D. Failover the replication sessions for the NAS Server and file systems

Question #185

While examining the health status of a Dell EMC Unity array, the administrator notices the internal
SSD is in a faulted state.

Which condition caused this fault?

A. BBU is not charged enough to keep the SSD powered on

B. There are only 5% of the spare blocks remaining on the SSD

C. SP Cache had too many dirty pages to copy to the SSD

D. There are no spare blocks remaining on the SSD

Question #186

You are implementing a new Dell EMC Unity 450F with twenty-five 7.6 TB SSD drives. You need to
standardize on a RAID5 4+1 stripe size.

What needs to be done to configure a dynamic pool?

A. use UEMCLI to configure the pool with all the drives specifying RAID5 4+1 stripe width.

B. Use the service account via UEMCLI to configure the pool with all the drives specifying a RAID5
4+1 stripe width.

C. Use Unisphere to build a traditional pool using RAID5 4+1. Convent the traditional pool to a
dynamic pool once the zeroing of the drives is complete.

D. Use Unisphere to select all the drives and select RAID5 4+1 in the drop-down box.
Question #187

What can be used to initially configure a static management IPv6 address on a Dell EMC Unity array?

A. symcli

B. navisecCLI

C. uemcli

D. initCLI

Question #188

Two fans have failed on the SPE. How much time does the Dell EMC Unity system allow before the
SP is shut down?

A. 2 min

B. 3 min

C. 4 min

D. 5 min

Question #189

What is a consideration when implementing a Thin Clone on a Dell EMC Unity array?

A. Thin Clone is only supported on physical Dell EMC Unity systems.

B. Thin Clone can be expanded independently from the base LUN

C. Thin Clone can be created directly from the base LUN

D. Data Reduction can be enabled independently on source LUN and on Thin Clone

Question #190

On a physical Dell EMC Unity system, what is the maximum size to which a UFS64 file system can be
extended?

A. 32 TB

B. 64 TB

C. 128 TB

D. 256 TB
Question #191

Which Dell EMC Unity service task would most quickly resolve connection problems between the
storage system and Unisphere?

A. Reinitialize the Storage System

B. Reimage the Storage Processors

C. Reboot the Storage Processors

D. restart the Management Software

Question #192

Which disk format is recommended for Dell EMC Unity's OVA?

A. Thick Provision Lazy Zeroed

B. raw

C. Thick Provision Eager Zeroed

D. Thin Provision

Question #193

What is used to create a Proxy NAS Server on a Dell EMC Unity array?

A. initCLI command

B. UEMCLI command

C. Unisphere GUI

D. Service command

Question #194

What are the supported options for the Professional Edition of the Dell EMC UnityVSA?

A. 4TB, 10 TB, and 50 TB

B. 4 TB, 25 TB, and 50 TB

C. 10 TB, 25 TB, and 50 TB

D. 10 TB, 30 TB, and 50 TB

Question #195

What is the role of Protocol Endpoints in Dell EMC Unity VMware storage provisioning?

A. Enable transparent host attach operations to Snapshots of VVol datastores

B. Manage host IO workload balance between multiple paths to the VMware datastores

C. Provide a write consistent view to the host when accessing multiple VMware datastores

D. Establish a data path between the ESXi host and the respective VVol datastores

Question #196

The soft limit quota for a file system has just been exceeded. What would you expect to occur
concerning data access?

A. Once the soft limit is reached, the grace period counts down until the hard limit is reached. New
data can be written as long as the hard limit has not been reached.

B. Once the soft limit is reached, no new data can be added to the file system or directory.

C. If the soft limit remains exceeded and the grace period expires, no new data may be added to the
particular file system or directory.

D. If the soft limit remains exceeded and the grace period expires, new data may be added to the
particular directory. The system will alert the grace period expired.

Question #197

On a Dell EMC Unity file system asynchronous session, how many system Snapshots, in total, are
required to support replication?

A. 1

B. 2

C. 4

D. 8

Question #198

When can a file system be defined as thin or thick?

A. Only when creating the file system

B. Any time after the file system has been created

C. Only when adding host access to the file system

D. Only when enabling data reduction on the file system

Question #199

A storage administrator is tasked with creating a DR solution for block and file storage resources. The
company has multiple regional and international sites containing a mix of physical and virtual Dell
EMC Unity systems.

What are considerations for the storage administrator in creating the DR solution?

A. Synchronous remote replication should be restricted to within 100 km between sites to keep
latency below ms Block storage resources can be replicated synchronously and asynchronously

B. Asynchronous replication ensures zero data loss the remote replica in disaster conditions Block
storage resources can be replicated synchronously and asynchronously

C. Asynchronous replication over long-distance does not impact latency Asynchronous replication
ensures zero data loss to the remote replica in disaster conditions

D. Synchronous remote replication should be restricted to within 100 km between sites to keep
latency below 10 ms File and block storage resources can be replicated synchronously and
asynchronously

Question #200

Fibre Channel access from a server to the Storage Processor can use what pathing options?

A. Single Path, Multipath, and Alternate path

B. Single path and Multipath only

C. Single Path and Alternate path only

D. Multipath only

Question #201

A storage administrator is tasked with configuring a density-based Host I/O policy based on the
following requirements:

Resource Size: 100 GB LUN -

Density Limit: 20 IOPS -

What is the total IOPS set by this policy?

A. 120

B. 1,200

C. 2,000

D. 2, 100
Question #202

A Storage administrator needs to expand their FAST Cache. The current configuration consists of
four 200 GB SAS Flash 2 drives.

What can be used to expand the FAST Cache?

A. Two 200 GB SAS Flash 2 drives

B. Two 400 GB SAS Flash 2 drives

C. Two 200 GB SAS Flash 3 drives

D. Two 400 GB SAS Flash 3 drives

Question #203

What are characteristics of the file system Snapshot Copy operation?

A. Parent can only be a read-only Snapshot Copy will be a read-only Snapshot Has an independent
Retention Policy from the parent

B. Parent can only be a read only Snapshot Copy will be a read/write Snapshot Inherits the parent
Retention Policy

C. Parent can be a read-only or a read/write Snapshot Copy will be a read/write Snapshot Inherits
the parent Retention Policy

D. Parent can be a read-only or read/write snapshot Copy will be a read-only Snapshot Has an
independent Retention Policy from the parent

Question #204

Observing the SPE Fault LED during initial power up, what colors and time duration does the SPE use
to indicate that it is ready for initialization?

A. Amber for 1 second, then blue for 3 seconds

B. Blue for 1 second, then green for 3 seconds

C. Amber for 1 second, then green for 2 seconds

D. Amber for 3 seconds, then blue for 1 second

Question #205

What is the default NFS host access option?

A. No Access

B. Read/Write, Allow Root

C. Read-Only

D. Read/Write

Question #206

A storage administrator needs to shrink their FAST Cache. The current configuration consists of eight
200 GB SAS Flash 2 drives.

What is the maximum number of drives that can be removed from FAST Cache through an online
shrink operation?

A. 2

B. 4

C. 6

D. 8

Question #207

Which protocols are supported by Dell EMC UnityVSA for storage provisioning?

A. iSCSI, NFS, and SMB

B. FC, NFS, and iSCSI

C. iSCSI and FC only

D. iSCSI and SMB only

Question #208

What is the maximum hierarchical Snapshot level, for both LUNs and file systems, on Dell EMC Unity
arrays?

A. 10

B. 16

C. 20

D. 32
Question #209

How can data at rest Encryption be activated on Dell EMC Unity?

A. Enable Data at rest Encryption at any time using Unisphere settings > manage Encryption

B. Enable data at rest Encryption, but only during initial configuration, using Unisphere settings >
Manage Encryption

C. Install data at rest Encryption license at any time using Unisphere Settings > Install License

D. Install data at rest Encryption, but only during initial configuration

Question #210

Which VVol object stores a copy of a VM's memory pages when the VM is powered on?

A. Config

B. Memory

C. Data

D. Swap

Question #211

A storage administrator is replicating a NAS Server from one Dell EMC Unity to another. The
destination system has a different network scheme than their source system.

What operation must be done on the destination system NAS Server to ensure data is accessible
after failover?

A. No changes required

B. Change the Override properties

C. Create a new interface

D. Modify DNS Cache

Question #212

What is the recommended configuration for iSCSI connections to ensure continuous access to the
Dell EMC Unity storage system in the event of a failover?

A. Set up iSCSI interfaces to use VLAN tagging and configure the host to utilize the same VLAN

B. Set up iSCSI interfaces on the same port of each SP and leverage the host-based multi-pathing
software.

C. Set up iSCSI interfaces on network ports on different SPs that are configured with Fail Safe
Networking (FSN)

D. Set up iSCSI interfaces on network ports that are configured with LACP on the same SP

Question #213

When creating a new LUN on a Dell EMC Unity array using Unisphere, what is the default setting of
the Data Reduction feature?

A. OFF for thick LUNs and ON for thin LUNs

B. ON for thick LUNs and OFF for thin LUNs

C. ON for thick LUNs in an All-Flash pool

D. OFF for thin LUNs in an All-Flash pool

Question #214

Which feature can be configured for a Dell EMC Unity file system NFS share?

A. Protocol Encryption

B. Host Access Level

C. Access-Based Enumeration

D. Branch Cache Enabled

Question #215

What is a characteristic of the iSCSI interface on Dell EMC Unity storage arrays?

A. IQNs are associated with an iSCSI interface.

B. IQN aliases are automatically generated.

C. Only one iSCSI interface can exist on a physical network port at a time.

D. A VLAN can only be assigned during the creation of the iSCSI interface.
Question #216

What is a characteristic of the IP Packet Reflect feature running on a Dell EMC Unity NAS Server?

A. SP must be rebooted after the feature is enabled on the NAS Server

B. Outbound packets use the same interface as the inbound packets

C. Communications initiated by the array do not require route table lookups

D. Feature can only be enabled when the NAS Server is created via UEMCLI.

Question #217

What is an example of a NAS Server replication session grouped operation?

A. Delete

B. Resume

C. Sync

D. Create

Question #218

What is the maximum number of Thin Clones that can be created from a Base LUN on a Dell EMC
Unity array?

A. 8

B. 16

C. 32

D. 64

Question #219

In Unisphere, a storage administrator has inadvertently disabled Data Reduction on an existing LUN.

What would result from this action?

A. A background LUN migration occurs, moving the data to a new LUN where it is inflated. New data
is neither deduplicated nor compressed.

B. Existing data is left in its current state. New data is neither deduplicated nor compressed.

C. Existing data is dynamically inflated to its full size, undoing the impact of deduplication and
compression. New data is neither deduplicated nor compressed.

D. Data Reduction, once enabled, cannot be disabled. New data is deduplicated or compressed.
Question #220

A storage administrator notices that all the configured HOST I/O Limits policies are Globally Paused.

How can the administrator put these policies into the Active state?

A. Select the Resume option on the Host I/O Limits Settings page

B. Select the Resume action for each Host I/O limits policy

C. Select the Active action for each Host I/O Limits policy

D. Select the Active option on the Host I/O Limits Settings page

Question #221

In Unisphere, where can a storage administrator create an asynchronous LUN replication session?

A. LUN Properties window only

B. Replication page only

C. Replication page or the LUN Properties window

D. LUN Creation wizard or the LUN Properties window

Question #222

What is a connectivity rule for a host that connects to multiple Dell EMC Unity systems?

A. Host must connect to all the arrays using a single protocol

B. Host can connect to different arrays with different protocols

C. iSCSI protocol is required to connect a host to multiple arrays

D. CAN connections to host must be used with alternating protocols

Question #223

What is a characteristic of FAST VP?

A. User can enable or disable FAST VP at the LUN level

B. FAST VP optimizes data placement by moving 1GB slices between disk tiers

C. Once enabled, FAST VP data relocation runs in background runs in background at all times

D. User can set the FAST VP data relocation rate