SOM-4487 Intel® Pentium® M Processor,

915GME/910GMLE ETX CPU Module

NEW SODIMM Socket

Features
 Embedded Intel Pentium M/Celeron® M processor +915GME + ICH6M
 Intel GMA 900 graphic engine, supports 24-bit LVDS
100 pin connector
SATA Connector
100 pin connector
(VGA/LCD/IrDA/  Supports DDR2 SODIMM up to 2 GB
KB/Mouse)
PCI/USB/Audio
 Supports 4 PCI, LPC, 2 SATAII, 1 IDE, 4 USB 2.0
 Supports embedded software APIs and Utilities

100 pin connector SATA Connector

(ISA) 100 pin connector Software APIs:
(IDE/Ethernet/Other)
Watchdog I2C SMBus H/W Monitor GPIO Backlight On/Off

Utilities:
BIOS flash Monitoring Flash Lock

Specifications
Form Factor ETX 3.0
CPU Intel Pentium M/Celeron M Processor
Front Side Bus 533/400 MHz
Processor System
System Chipset Intel 915GME (910GMLE) GMCH/ICH6M
BIOS AWARD 4 Mbit Flash BIOS
Technology DDR2 400/533 MHz (400 MHz for 910GMLE)
Memory Max. Capacity up to 2 GB
Socket 1 x 200-pin SODIMM socket
Chipset Intel 915GME(910GMLE)
VRAM DVMT 3.0 supports up to 128 MB
Graphics Engine Mobile Intel GMA900 3D/2D engine
Display
LCD Single and dual channel 18/36-bit LVDS
VGA up to 2048 x 1536
Dual Display CRT + LCD
Chipset Intel 82562GZ 10/100 Mbps Ethernet
Ethernet
Speed 10/100 Mbps
WatchDog Timer 256 timer intervals, from 1 to 255 sec or min setup by software, jumperless selection, generates system reset
Expansion 4 x PCI master, ISA
PATA 1 x EIDE (UDMA 100)
SATA 2 x SATA (On ETX CPU module)
USB 4 x USB 2.0
I/O Audio Realtek ALC203 AC97 Codec support Line-in/out, Mic-in
GPIO 1-bit GPIO
COM 2 COM ports
FDD/LPT 1 x FDD or LPT
Power Type ATX, AT
Power Supply Voltage +5 V only (+5 VSB needs for ATX)
Typical: (1 GB DDR2 533)
+5 V @ 3.66 A (Intel Pentium M 760, 2.0G) (915GME)
Power Consumption +5 V @ 2.63 A (Intel Pentium M LV 738, 1.4G) (915GME)
(Typical) +5 V @ 2.40 A (Intel Celeron M 373, 1.0G) (910GMLE)
+5 V @ 2.37 A (Celeron M 373 0KB, 1.0G) (910GMLE)
Power
+5 V @ 2.23 A (Celeron M 600MHz) (910GMLE)
Max: (1 GB DDR2 533)
+5 V @ 6.12 A (Intel Pentium M 760, 2.0G) (915GME)
Power Consumption +5 V @ 3.84 A (Intel Pentium M LV 738, 1.4G) (915GME)
(Max, test in HCT) +5 V @ 3.13 A (Intel Celeron M 373, 1.0G) (910GMLE)
+5 V @ 3.08 A (Celeron M 373 0KB, 1.0G) (910GMLE)
+5 V @ 2.82 A (Celeron M 600MHz) (910GMLE)
Operating Temperature 0 ~ 60° C (32 ~ 140° F)
Environment
Operating Humidity 0% ~ 90% relative humidity, non-condensing
Mechanical Dimensions 114 x 95 mm (4.5" x 3.74")

Computer On Modules
All product specifications are subject to change without notice Last updated : 22-April-2010
 SOM-4487

Board Diagram
Intel Pentium-M CPU
Intel Celeron-M CPU
Socket 479

FSB 533/400 MHz

Analog RGB
Intel GMCH
LVDS BUS 910GMLE (400 MHz)
915GME (533/400 MHz)
DDRII SDRAM
DDRII 533/400
200-pin SODIMM x 1

DMI

USB 2.0 x 4
PATA x 1
ETX Conn.

ETX Conn.
PCI BUS

2 SATA Conn.
SATA x 2 Intel ICH6M
On-Board PCI IT8888G ISA

82562GZ
ALC203 AC97 LCI
LAN 10/100

FWH
LPC Bus
BIOS

PS/2 KB & MS
LPC Super I/O
COM1 / COM2 LPT / Floppy IR
W83627HG

Ordering Information
L2 10/100 AC97 USB ATX AT Thermal Operating
Part No. CPU Chipset LVDS VGA PCI SATA
Cache LAN Audio 2.0 Power Power Solution Temp.
SOM-4487FL-00A1E Socket 915GME 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Active 0 ~ 60° C
Pentium M LV
SOM-4487FL-S4A1E 2 MB 915GME 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Active 0 ~ 60° C
738
SOM-4487FL-S1A1E Celeron M 373 512 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C
Celeron M
SOM-4487FL-M0A1E 512 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C
600 MHz
Celeron M
SOM-4487FL-S0A1E 0 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C
1 GHz

Development Board Packing List

Part No. Description Part No. Description Quantity
SOM-DB4400-00A2E Development Board for ETX Rev.A2 SOM-4487 CPU Module 1
SOM-DB4700-00A1E Development Board for ETX Rev.A1 Utility CD 1
1960028600N00B Heatspreader (SOM-4487FL-00A1E only) 1
Heatspreader (SOM-4487FL-M0A1E,
Optional Accessories 1960028601N00B SOM-4487FL-S0A1E, SOM-4487FL-S1A1E, SOM-
4487FL-S4A1E)
1

Part No. Description

1960012091T00S
1750001980
Semi-Heatsink 114 x 96 x 15 mm
Semi-Cooler 114 x 96 x 15 mm 12 V Fan
Embedded OS
OS Part No. Description
CE60 Pro Intel (852/855/915/945)
WinCE 6.0 Pro 2070007811
2COM V1.2 ENG
QNX 6.4.1 BSP ready

Online Download www.advantech.com/products

 Value-Added Software Services
Software API: An interface that defines the ways by which an application program may request services from libraries and/or operating systems. Provides not only the underlying
drivers required but also a rich set of user-friendly, intelligent and integrated interfaces, which speeds development, enhances security and offers add-on value for Advantech platforms.
It plays the role of catalyst between developer and solution, and makes Advantech embedded platforms easier and simpler to adopt and operate with customer applications.

Software APIs
Control Monitor
General Purpose Input/Output is a flexible parallel interface
A watchdog timer (WDT) is a device that performs a specific
that allows a variety of custom connections. It allows users
operation after a certain period of time if something goes wrong
to monitor the level of signal input or set the output status to
and the system does not recover on its own.
switch on/off a device. Our API also provides Programmable
A watchdog timer can be programmed to perform a warm boot
GPIO, which allows developers to dynamically set the GPIO
GPIO Watchdog (restarting the system) after a certain number of seconds.
input or output status.

SMBus is the System Management Bus defined by Intel®

Corporation in 1995. It is used in personal computers and
servers for low-speed system management communications. The Hardware Monitor (HWM) API is a system health
The SMBus API allows a developer to interface a embedded supervision API that inspects certain condition indexes, such as
system environment and transfer serial messages using the fan speed, temperature and voltage.
SMBus protocols, allowing multiple simultaneous device Hardware
SMBus
control. Monitor

I2C is a bi-directional two wire bus that was developed by

Philips for use in their televisions in the 1980s. The Hardware Control API allows developers to set the PWM
The I2C API allows a developer to interface with an embedded (Pulse Width Modulation) value to adjust fan speed or other
system environment and transfer serial messages using the I2C devices; it can also be used to adjust the LCD brightness.
protocols, allowing multiple simultaneous device control. Hardware
I2C
Control

Display Power Saving

Make use of Intel SpeedStep technology to reduce power power

The Brightness Control API allows a developer to interface with
consumption. The system will automatically adjust the CPU
an embedded device to easily control brightness.
Speed depending on system loading.
Brightness
CPU Speed
Control

Refers to a series of methods for reducing power consumption in

The Backlight API allows a developer to control the backlight
computers by lowering the clock frequency. These APIs allow the
(screen) on/off in an embedded device.
user to lower the clock from 87.5% to 12.5%.
System
Backlight
Throttling

Software Utilities
The BIOS Flash utility allows customers to update the flash The eSOS is a small OS stored in BIOS ROM. It will boot up in
ROM BIOS version, or use it to back up current BIOS by case of a main OS crash. It will diagnose the hardware status,
copying it from the flash chip to a file on customers’ disk. The and then send an e-mail to a designated administrator. The
BIOS Flash utility also provides a command line version and eSOS also provides remote connection: Telnet server and FTP
BIOS Flash API for fast implementation into customized applications. eSOS server, allowing the administrator to rescue the system.

The embedded application is the most important property of Flash Lock is a mechanism that binds the board and CF card
a system integrator. It contains valuable intellectual property, (SQFlash) together. The user can “Lock” SQFlash via the Flash
design knowledge and innovation, but it is easily copied! The Lock function and “Unlock” it via BIOS while booting. A locked
Embedded Security ID utility provides reliable security functions SQFlash cannot be read by any card reader or boot from other
Embedded for customers to secure their application data within embedded Flash Lock platforms without a BIOS with the “Unlock” feature.
Security ID BIOS.

The Monitoring utility allows the customer to monitor system

health, including voltage, CPU and system temperature and fan
speed. These items are important to a device; if critical errors
happen and are not solved immediately, permanent damage may
Monitoring be caused.

Industrial Motherboards