Operation and Maintenance

Instructions Manual
JU/JW MODEL ENGINES
FOR
FIRE PUMP APPLICATIONS

This manual covers John Deere Engines

prepared by Clarke
for fire pump service

Clarke UK, Ltd. Clarke Fire Protection Products, Inc.

Unit 1, Grange Works 3133 E. Kemper Road
Lomond Road Cincinnati, OH 45241
Coatbridge U.S.A.
ML5 2NN
United Kingdom
TELE: +44(0)1236 429946 TELE: +1.513.771.2200
FAX: +44(0)1236 427274 FAX: +1.513.771.0726

www.clarkefire.com

MP-7 09/08
C13960 rev P
 CONTENTS
SUBJECT PAGE
1.0 INTRODUCTION 5
1.1 IDENTIFICATION/NAMEPLATE 5
1.2 SAFETY/CAUTION/WARNINGS 6
2.0 INSTALLATION/OPERATION 10
2.1 TYPICAL INSTALLATION 10
2.2 ENGINE STORAGE 11
2.2.1 Storage Less than 1 year 11
2.2.2 Extended Storage Maintenance Procedure 11
2.3 INSTALLATION INSTRUCTIONS 11
2.4 SPECIFIC FLYWHEEL COUPLING ALIGNMENT INSTRUCTIONS 13
2.4.1 Listed Driveshaft 13
2.4.2 Driveshaft 13
2.4.3 Other Coupling Types 15
2.5 WEEKLY TEST 15
2.6 STARTING/STOPPING THE ENGINE 15
2.6.1 Special Notes to Equipment Installer of an LPCB Approved (LPS1239) Engine Model 15
2.6.2 To Start Engine 15
2.6.3 To Stop Engine 19
3.0 ENGINE SYSTEMS 19
3.1 FUEL SYSTEM 19
3.1.1 Bleeding the Fuel System 19
3.1.1.1 JU4/6 UF, NL 19
3.1.1.2 JU4/6 LP 20
3.1.1.3 JW6 UF, NL 20
3.1.2 Draining the Condensate from the Fuel Filter 21
3.1.3 Changing Fuel Filter Cartridge 22
3.1.3.1 JU4/6 UF, NL 22
3.1.3.2 JU4/6 LP 22
3.1.3.3 JW6 UF, NL 22
3.1.4 Fuel Tanks 23
3.1.5 JU Fuel Injection Pump Components 23
3.1.6 JW Fuel Injection Pump Components 24
3.2 AIR/EXHAUST SYSTEM 24
3.2.1 Ambient Conditions 24
3.2.2 Ventilation 25
3.2.3 Standard Air Cleaner 25
3.2.4 Crankcase Ventilation 26
3.2.4.1 Open Crankcase Ventilation 26

Page 2 of 41
 3.2.4.2 Crankcase Ventilation System 25
3.2.5 Exhaust System 26
3.3 LUBRICATION SYSTEM 26
3.3.1 Checking Sump Oil 26
3.3.2 Changing Engine Oil 26
3.3.3 Changing Oil Filter Cartridge 26
3.3.4 Oil Specification 27
3.3.5 Oil Capacities 27
3.4 COOLING SYSTEM 27
3.4.1 Engine Coolant 27
3.4.2 Water 28
3.4.3 Coolant Capacities 28
3.4.4 Coolant Inhibitors 28
3.4.5 Procedure for Filling Engine 29
3.4.5.1 Engines without Coolant Recovery Tank 29
3.4.5.2 Engines with Coolant Recovery Tank 30
3.5 ELECTRICAL SYSTEM 30
3.5.1 Wiring Diagrams 30
3.5.2 Checking Drive Belt Tension and Adjustment 30
3.5.3 Speed Switch 31
3.5.4 Magnetic Pick-Up 31
3.6 ENGINE SPEED ADJUSTMENT 31
4.0 MAINTENANCE SCHEDULE 32
4.1 ROUTINE MAINTENANCE 32
5.0 TROUBLE SHOOTING 32
6.0 PARTS INFORMATION 32
6.1 SPARES 32
6.2 ENGINE MAINTENANCE PARTS LIST 33
7.0 OWNER ASSISTANCE 33
8.0 WARRANTY 33
8.1 GENERAL WARRANTY STATEMENT 33
8.2 CLARKE WARRANTY 33
8.3 JOHN DEERE WARRANTY 34
9.0 ATCM CALIFORNIA EMISSION REGULATIONS FOR STATIONARY ENGINES 36
10.0 INSTALLATION & OPERATION DATA (See Technical Catalog C13965) 37
11.0 WIRING DIAGRAMS (See Technical Catalog C13965) 37
12.0 PARTS ILLLUSTRATION (See Technical Catalog C13965) 37
13.0 APPENIX (Alpha Index) 38

Page 3 of 41
Check factory availability for a manual in one of the following languages:

Spanish MP-7 C13961

French MP-7 C13962
German MP-7 C13963
Italian MP-7 C13964

NOTE
The information contained in this book is intended to assist operating personnel by providing
information on the characteristics of the purchased equipment.

It does not relieve the user of their responsibility of using accepted practices in the installation,
operation, and maintenance of the equipment.

NOTE: CLARKE FPPG Reserves the right to update the contents of this publication without
notice.

Page 4 of 41
1.0 INTRODUCTION efficiently, and perform routine servicing correctly.
Please read it carefully.
SCOPE OF SUPPLY
MODEL NUMBERING & IDENTIFICATION
The following paragraphs summarize the “Scope of
Supply” of the Engine: There are two identification plates attached to each
engine. Clarke Identification Plate: Engine Model,
• The CLARKE Engine supplied has been Serial Number, Rating and Date of Manufacture are
designed for the sole purpose of driving a shown on this identification plate. The JU Series
stationary Emergency Fire Pump. It must not identification plate is mounted on the flywheel
be used for any other purpose. housing at the rear of the engine. The JW Series
identification plate is mounted on right rear engine
• Shall not be subjected to Horsepower mount.
requirements greater than the certified
nameplate rating (for UL/cUL/FM/LPCB Note that there are five types of identification plates,
only). dependent on whether the engine is a “Non-Listed”
or “Listed/Approved” Model. These are typical
• Engines must be sized to cover fully the examples. (See Figure #1).
maximum power absorbed by any particular
driven equipment together with a safety Clarke Identification Plates
factor on no less than 10%. (For Non-listed USA Non Listed USA Listed/Approved
only).

• Derates for elevation and temperature need to

be considered for maximum pump power.

• Fuel delivery settings are factory set with-in

the injection pump and must not be tampered
with or adjusted. Minor RPM adjustments to
meet pump requirements are permissible.

• The engine shall be installed and maintained

in accordance with the guidelines stated in
this manual and technical catalog (C13965).
UK Non-Listed UK Listed/Approved
• Periodic running checks to ensure
functionality should be kept to a maximum of
½ hour per week.

1.1 IDENTIFICATION/NAMEPLATE

• Throughout this manual, the terms “Engine”

and “Machine” are used.

• The term “Engine” refers solely to the diesel

engine driver as supplied by CLARKE.

• The term “Machine” refers to any piece of

equipment with which the engine might Figure #1
interface.

This manual provides all the information necessary to

operate your newly acquired engine safely and

Page 5 of 41
 UK Listed/Approved Number and Serial Number. On the JW Series, the
John Deere Serial identification plate is located on
the left-hand side of the engine between the intake
manifold and starting motor. On the JU Series, the
John Deere identification plate is located on the right
side of the cylinder block behind the fuel filter.

1.2 SAFETY/CAUTION/WARNINGS

ATTENTION: This engine has components and

fluids that reach very high operating temperatures
Figure #1 cont’d and is provided with moving pulleys and belts.
Approach with caution. It is the responsibility of the
The Clarke eight digit model numbers reflects the builder of the machine using a Clarke engine to
base engine type, number of cylinders, cooling optimize the application in terms of maximum end
system, approval listing and a power rating code. user safety.
Example: JU6H-UF50
• J = John Deere base engine prepared by BASIC RULES
CLARKE
• U = base engine series (4.5 liter 4 cylinder or The following recommendations are given to reduce
6.8 liter 6 cylinder) the risk to persons and property when an engine is in
• 6 = number of cylinders service or out of service.
• H = Heat Exchanger cooled (R = Radiator)
Engines must not be used for applications other than
• UF = Underwriters Laboratories Listed/
those declared under “Scope of Supply”.
Factory Mutual Approved, (LP = LPCB Loss
Prevention Council Board Approved, NL =
Incorrect handling, modifications and use of non-
Non-Listed)
original parts may affect safety. When lifting the
• 50 = A power rating code
engine, take care to use suitable equipment to be
applied to the points specially provided as shown on
The Clarke 10 digit model numbers reflects the base
the appropriate Engine Installation Drawing. Engine
engine type, number of cylinders, cooling system,
weights are shown in figure #2
approval listing, manufacturing location, emissions
ENGINE MODEL WEIGHT lbs (kg)
code and a power rating code. JU4H-UF10,12,14,20,22 ,24 910 (413)
Example: JU6H-UFAB54 JU4H-NL14,20,22,24
JU4H-LP20,24
• J = John Deere base engine prepared by JU4H-UFAB26
CLARKE JU4H-UF28,30,32,34.40,42,44,50,
• U = base engine series (4.5 liter 4 cylinder or 52,54,H8,H0,H2,58
935 (424)
JU4H-NL30,32,,34,40,42,50,52,54
6.8 liter 6 cylinder) JU4H-LP50,54, L4
• 6 = number of cylinders JU4H-UF84, JU4H-LP84 1085 (492)
• H = Heat Exchanger cooled (R = Radiator) JU4R-UF09,UF11,13,19,21,23 956 (434)
JU4R-NL09,UF11,13,19,21,23
• UF = Underwriters Laboratories Listed/ JU4R-UF40,49,51,53
Factory Mutual Approved, (LP = LPCB Loss 982 (445)
JU4R-NL40,49,51,53
Prevention Council Board Approved, NL = JU6H-UF30,32,34,50,52,54
D0,D2,G8,M8,M0,M2,58
Non-Listed) JU6H-UFABL0,2,8,54 1657 (750)
• A=Manufacturing Location (A= Cincinnati, JU6H-NL30,32,34,50,52,54
B= Coatbridge) JU6H-LP50,54
JU6H-UF60,62,68,84
• B= EPA NSPS Complaint (A= Non- JU6H-UFAB76,84
Emissioned, C=EPA Tier 2 Certified, JU6H-NL60,62,74,84 1693 (766)
JU6H-LP60,84
D=EPA Tier 3 Certified, E=EPA Interim Tier JW6H-UF30 (JDFP-06WA),38
4 Certified) 2012 (910)
JW6H-NL30
• 54 = A power rating code JW6H-UF40 (JDFP-06WR),48 2003 (906)
JW6H-NL40
JW6H-UF50,60,58,H8 2053 (929)
John Deere Identification Plate: The second JW6H-NL50, 60
identification plate contains the John Deere Model Figure #2

Page 6 of 41
Figure #3 shows the typical lifting arrangement of a
bare engine. Note the lifting points on the engine are
for lifting the engine only. Caution, when lifting, lift
point should always be over the equipment Center of
Gravity.

Figure #3

Figure #4 shows the typical lifting arrangement of a

base mounted engine and pump set when the base (or
module) is furnished with lifting holes.

Figure #4

When Clarke furnishes the base (or module) for the

engine and pump set, the combined weight of the
engine and base (or module) will be indicated on the
unit. Caution, when lifting, lift point should
always be over the equipment Center of Gravity.

Note: The engine produces a noise level exceeding

70 dB(a). When performing the weekly functional
test, it is recommended that hearing protection be
worn by operating personnel.

CLARKE UK provides the machine manufacturer

with a “Declaration of Incorporation”
for the Engine, when required, a copy of which is
enclosed in the manual. This document clearly states
the machine manufacturers’ duties and
responsibilities with respect to health and safety.
Refer to Figure #5.

Page 7 of 41
 GRANGE WORKS, LOMOND ROAD, COATBRIDGE, UNITED KINGDOM, ML5 2NN

TEL: 0044 1236 429946 FAX: 0044 1236 427274

DECLARATION OF INCORPORATION

We hereby declare that the engine is intended to be incorporated into other machinery and must not be put into service until the
relevant machinery, into which the engine is to be incorporated, has been declared in conformity with the essential health and
safety requirements of the machinery Directive 98/37 EC and consequently the conditions required for the CE Mark.

We declare that the engine is manufactured in accordance with the following Standards and Directives:
Directive 98/37 EC, 89/336 EEC, 73/23 EEC.
Standards EN 292, Part 1 and Part 2, EN 60204-1

1) Description – Diesel Engines

Manufacturer – Clarke UK
Model Number –
Serial Number –
Year of Manufacture –
Contract Number –
Customer Order Number –

2) The engine has moving parts, areas of high temperatures and high temperature
fluids under pressure. In addition it has an electrical system which may be under
strong current.

3) The engine produces harmful gases, noise and vibration and it is necessary to
take suitable precautionary measures when moving, installing and operating the
engine to reduce risk associated with the characteristics stated above.

4) The engine must be installed in accordance with local laws and regulations. The
engine must not be started and operated before the machinery into which it is to
be incorporated and/or its overall installation has been made to comply with local
laws and regulations. The engine must only be used in accordance with the scope
of supply and the intended applications.

Signed ___________________________________ Date: _______________

John Blackwood – General Manager

REGISTERED IN SCOTLAND NO: 81670 C13896, Rev. E April 2007

Figure #5

WHAT TO DO IN AN EMERGENCY If operating mistakes cause accidents call for help

If operating mistakes cause accidents call for help
Any user of the Engine who follows the instructions immediately from the EMERGENCY SERVICES.
set out in this manual, and complies with the In the event of an emergency, and while awaiting the
arrival of the EMERGENCY SERVICES, the
instructions on the labels affixed to the engine are following general advice is given for the provision of
working in safe conditions. first aid.

Page 8 of 41
FIRE 2) Caustic burns to the eyes are caused by
battery acid, lubricating oil and diesel fuel.
Put out the fire using extinguishers recommended by * Wash the eye with running water for
the manufacturer of the machine or the installation. at least 20 minutes, keeping the
eyelids open so that the water runs
BURNS over the eyeball and moving the eye
1) Put out the flames on the clothing of the in all directions.
burns victim by means of:
* drenching with water ELECTROCUTION
* use of powder extinguisher, making
sure not to direct the jets onto the Electrocution can be caused by:
face
* blankets or rolling the victim on the 1) The engine’s electrical system (12/24
ground VDC)
2) Do not pull off strips of clothing that are 2) The electrical coolant pre-heating system
sticking to the skin. 120/240 Volt AC (if supplied) AC current.
3) In the case of scalding with liquids, remove
the soaked clothing quickly but carefully. In the first case, the low voltage does not involve
4) Cover the burn with a special anti-burn high current flows through the human body;
packet or with a sterile bandage. however, if there is a short circuit, caused by a metal
tool, sparks and burns may occur.
CARBON MONOXIDE POISONING (CO) In the second case, the high voltage causes strong
currents, which can be dangerous.
Carbon monoxide contained in engine exhaust gases If this happens, break the current by operating the
is odorless and dangerous because it is poisonous and switch before touching the injured person.
with air, it forms an explosive mixture.
If this is not possible, bear in mind that any other
Carbon monoxide is very dangerous in enclosed attempt is highly dangerous also for the person
premises because it can reach a critical concentration assisting; therefore, any attempt to help the victim
in a short time. must be carried out without fail using means that are
insulating.
When attending a person suffering from CO
poisoning in enclosed premises, ventilate the WOUNDS AND FRACTURES
premises immediately to reduce the gas
concentration. The wide range of possible injuries and the specific
nature of the help needed means that the medical
When accessing the premises, the person providing services must be called.
the aid must hold his breath, not light flames, turn on
lights or activate electric bells or telephones so as to If the person is bleeding, compress the wound
avoid explosions. externally until help arrives.

Take the victim to a ventilated area or into the open In the case of fracture do not move the part of the
air, placing him on his side if he is unconscious. body affected by the fracture. When moving an
injured person permission from that person must be
CAUSTIC BURNS received until you can help him. Unless the injury is
life threatening, move the injured person with
1) Caustic burns to the skin are caused by acid extreme care and then only if strictly necessary.
escaping from the batteries:
* remove the clothes WARNING LABELS
* wash with running water, being
careful not to affect injury-free areas Warning labels, in picture form, are applied to the
engine. Their meanings are given below.

Page 9 of 41
Important Note: Labels that show an exclamation Jacket Water Heater Voltage
mark indicate that there is a possibility of danger.

Heat Exchanger Maximum Working Pressure

Air Filter Installation

Coolant Mixture

2.0 INSTALLATION/OPERATION

Lifting Point 2.1 TYPICAL INSTALLATION

A typical Fire Pump installation is shown in Figure

#6 & 6A.
1. Pump/Engine set
2. Main Pump Controller
3. Pump discharge
4. Air louver
5. Entrance door with air louver
6. Exhaust silencer
Automatic Start 7. Exhaust system supports
8. Exhaust outlet pipe
9. Concrete base
10. Exhaust flexible connection joint/pipe
11. Air Discharge Duct from Radiator

Rotating Parts

Figure #6
Typical Installation
Heat Exchanger Cooled Engine

Page 10 of 41
 8) Start and run the engine at a slow speed for
1-2 minutes being careful not to exceed the
normal operating temperature.
11 9) Drain the oil and coolant.
10) Replace the protective plugs that were used
for shipping and storage.
11) Attach to the engine a visible card, specifying
“ENGINE WITHOUT OIL” DO NOT
OPERATE”.
Figure #6A
Typical Installation IMPORTANT: THIS TREATMENT MUST BE
Radiator Cooled Engine REPEATED EVERY 6 MONTHS
************************
2.2 ENGINE STORAGE PUTTING ENGINE INTO SERVICE AFTER
ADDITIONAL PRESERVATION SERVICE:
2.2.1 Storage less than 1 year To restore the normal operation running conditions of
the engine, carry out the following:
Storing engines requires special attention. Clarke
engines, as prepared for shipment, may be stored for 1) Fill the engine sump with the normal
a minimum of one year. During this period, they recommended oil, to the required level.
should be stored indoors in a dry environment. 2) Remove the protective plugs used for
Protective coverings are recommended provided they shipping and storage.
are arranged to allow for air circulation. The stored 3) Refill cooling water to proper level.
engine should be inspected periodically for obvious 4) Remove the card “ENGINE WITHOUT OIL,
conditions such as standing water, part theft, excess DO NOT OPERATE”.
dirt buildup or any other condition that may be 5) Follow all steps of the Installation
detrimental to the engine or components. Instructions when the engine will be put into
Any such conditions found must be corrected service.
immediately.
2.3 INSTALLATION INSTRUCTIONS
2.2.2 Extended Storage Maintenance Procedure
The correct installation of the engine is very
After a one year storage period or if the engine is important to achieving optimum performance and
being taken out of service for more than 6 months, extended engine life.
additional preservation service must be performed as
follows: In this respect, the engine has certain installation
requirements, which are critical to how it performs.
1) Drain the engine oil and change the oil filter. These requirements are generally associated with the
2) Refill the engine crankcase with MIL-L- cooling, exhaust, induction air, and fuel systems.
21260 preservative oil.
3) Change the fuel filter. This section of the manual should be read in
4) Install the coolant plugs and install coolant in conjunction with the relevant Installation and
the normal mix percentage of 50% coolant, Operation Data Sheets. If there is any doubt about an
50% water, premixed. installation, contact should be made with Clarke
5) Remove the protection from the intake and Customer Support giving exact details of the
exhaust openings. problem.
6) Prepare a container as a fuel source using a
mixture of Mobilarma or Sta-Bil with Diesel All installations should be clean, free of any debris
#2 fuel or “Red” diesel fuel (ASTM D-975) and dry. Care should be taken to ensure that there is
or BS2869 Class A2. easy access to the engine for maintenance and repair.
7) Disconnect the coupling or drive shaft from The safety of personnel who may be in the area of the
the pump.

Page 11 of 41
engine when it is running is of paramount importance for cooling system capacity. Refer to section
when designing the installation layout. 3.4.5 for filling procedure.
1) Secure pump set to foundation and complete 5) Engine is shipped with oil installed. For
installation in accordance with pump make-up oil specification refer to section 3.3
manufacturer’s instructions. Perform engine- Lubrication System.
to-pump coupling alignment. Lubricate Falk 6) Connect fuel supply and return line to fuel
coupling with supplied grease or driveshaft supply tank plumbing. Reference the Fuel
universal joints with NLGI grade #1 or #2 System section of the Installation and
grease at the (3) Zerk fittings. (Refer to Operation Data in the Technical Catalog, for
section 2.4 for specific alignment piping size, maximum allowable fuel pump
instructions). suction, and maximum allowable fuel head
2a) Engine with Heat Exchanger Cooling: requirements. Fill supply tank with #2 diesel
Install the heat exchanger discharge pipe. fuel (ASTM D-975) or BS 2869 Class A2
The discharge pipe should be no smaller than “Red” diesel fuel, bleed supply system of air
the outlet connection on the heat exchanger. and check for leaks. Fuel supply level must
Discharge water piping should be installed in meet applicable code requirements. Do not
accordance with applicable codes. All use a copper based or galvanized material for
plumbing connecting to the heat exchanger any component of a diesel fuel system. The
must be secured to minimize movement by fuel will chemically react with the zinc
the engine. Cooling loop water pressure to resulting in clogged fuel filters and injector
the heat exchanger must not exceed the limit systems.
that is stated on the heat exchanger supplied 7) Remove protective covering on air cleaner
with the engine. element.
2b) Engine with Radiator Cooling: 8) Connect jacket water heater (if supplied) to
Connect radiator air discharge ducting to AC power source. For JU4/6 Series the
radiator duct flange. Discharge ducting electrical supply requirements are indicated
should be installed in accordance with on the heater body. Connect the supplied
applicable codes. A flexible duct section heater connection wire directly to a customer
should be provided to isolate engine from supplied electrical junction box. For
building. JDFP/JW6 Series the electrical supply
3) Install all engine cooling system draincocks requirements are indicated on the connection
and plugs. box. Connect to the heater directly to the
Engine junction box at the end of the heater only.
Qty Description Location Model Supply wiring should never be routed
1 1/8” Water Heater JU4/6H, through the engine gauge panel. Severe
draincock inlet tube JU4/6R damage to critical engine control components
1 1/8” Coolant heater JDFP, could result. Energize heater only after step
draincock inlet tube JW6 #4 is completed.
1 Plug Oil Cooler JU4/6H, 9) Connect exhaust system to flexible
RE46686 JU4/6R connection on the engine. The exhaust
1 3/8” pipe plug Heat exchanger JDFP, system plumbing must be supported by the
JW6 building structure and not the engine. The
1 Electrode Bottom of heat JU4/6H exhaust flexible connection is provided only
plug exchanger for the purpose of thermal expansion and
4) Fill engine cooling system with premixed vibration isolation, not for misalignment or
50% water / 50% coolant solution. Use only directional change.
coolants meeting ASTM-D4985 10) Make electrical DC connections between the
specifications for heavy-duty diesel engines. engine gauge panel terminal strip (if
Never use light-duty or automotive coolants supplied) and the controller per the controller
in the engine that are stated as ASTM-D3306 manufacturer’s instructions. Note that the
only. Refer to Figure #34 in section 3.4.3 “W” terminal is used only for the UL/FM
cooling water solenoid (if supplied). Refer to

Page 12 of 41
 the wiring diagram sticker located on the re-torque all driveshaft connection bolts to the values
inside cover of the engine gauge panel for given in the following table:
proper connection of the water solenoid.
11) Fill batteries with electrolyte per battery
manufacturer’s instructions. Connect cables
between engine and batteries only after BOLT SIZE TIGHTENING
electrolyte is installed. Refer to the wiring DRIVE /MATERIAL TORQUE
diagram inside the engine gauge panel cover MODELS SHAFT GRADE ft-lbs
(N-m)
(if supplied), or appropriate wiring diagram
in the Technical Catalog C13965, for correct JU4H-10,12, 7/16-20
14,20,22,24 SC41 Grade 8 50 - 55
positive and negative connections. Connect SC41A
negative cables directly to the engine block. JU4R-09, (Hi-Tensile) (68 – 75)
On JU4/6 Series connect each positive cable 11,13,19,21,23
to the large electrical post of the starter JU4H-UFAB26
motor. Note: the JU4/6 Series have a JU4H-
separate starter motor for each battery set. 28,30,32,34,40,
42,44,50,52,54, SC55 1/2-20 75 - 82.5
On the JDFP/JW6 Series connect each SC55A
positive cable to the large outer post of the H8,H0,H2,58, Grade 8 (102 – 112)
manual starting contactors. 84 (Hi-Tensile)
12) Note: Clarke Operation and Maintenance JU4R-
Instructions Manual and Clarke parts 40,49,51,53
illustration pages are located inside the JU6H- 90 - 99
UFDO,D2,30, SC2130 M12,Class (122 – 134)
engine gauge panel.
32,34,G8,M8, or 10.9 (see note #1)
13) IMPORTANT! In order to obtain prompt SC2130A
Warranty Service and to comply with M2,58,50,52,54 (Metric)
or
Emissions Regulations, this engine must be JU6H- (Hi-Tensile 86 – 94
SC55L-A
registered to the final installation name and UFABL8, L0, (117 - 128)
address. To register this engine, go to L2, 54 (see note #2)
www.clarkefire.com and select Warranty 90 - 99
Registration. (122 – 134)
JU6H-UF68, SC2130 M12,Class (see note #1)
60, 62, 84 or 10.9
2.4 SPECIFIC FLYWHEEL COUPLING SC2130A
ALIGNMENT INSTRUCTIONS JU6H- (Metric) 86 – 94
or
UFAB76,84 SC61L-A (Hi-Tensile (117 - 128)
2.4.1 Listed Driveshafts (see note #2)
Refer to Listed Driveshaft Installation, 90 - 99
Operation and Maintenance Manual M12,Class (122 – 134)
C132355 10.9 (see note #1)
All JW6 SC2130A (Metric)
or
2.4.2 Driveshaft (Hi-Tensile) 86 – 94
SC81A
(117 - 128)
To check the alignment of the pump shaft and engine (see note #2)
crankshaft centerlines for proper Parallel Offset and
Angular tolerance, the driveshaft must be installed Note 1 – It is recommended that a medium strength
between the flywheel drive disc (no drive disc on threadlocker (i.e. Loctite – blue #64040) be used in
JW6 models) and the flanged hub on the pump shaft. the assembly and torquing of all hardware. This may
be purchased as part number 23509536.
Before removing the driveshaft guard, disconnect the
negative battery cable from both batteries. Note 2 – 4 of the hi-tensile bolts and/or nuts, that are
used to connect the driveshaft to the drive disc (all
Before beginning the alignment checks and making JU6 models) or flywheel (all JW6 models) and that
any necessary corrections, install the driveshaft and connect the driveshaft to the pump companion flange,

Page 13 of 41
will require a “crow’s foot” wrench attached to a 1. Measure from the front face of the drive shaft
standard torque wrench in order to apply the required flange on the pump end to point B. (Point B
tightening torque. A standard socket will not work is the bearing bore on the exhaust side of the
due to close proximity of the bolts and/or nuts with engine). This measurement must be equal to
the driveshaft yoke. The tightening torque values the measurement at point A + 1 mm.
listed for these bolts and/or nuts have been corrected C) To check the Vertical Parallel Offset, the
for using a “crow’s foot” adapter which extends the driveshaft must be re-orientated.
standard torque wrench’s length. 1. Rotate the shaft 90○ so the reference “CD” on
the flywheel drive disc or the circumference
The following steps describe the proper way to check of the drive shaft flange (against the
alignment. A small pocket scale or ruler with flywheel) is in the position shown on
millimeter markings is recommended to make all Figure#8.
measurements. 2. Measure from the rear face of the flywheel
drive disc or the drive shaft flange to point C.
A) To check the Horizontal Parallel Offset, the (Point C is the same as point A with the
driveshaft must be in the proper orientation. driveshaft rotated 90°). The measurement
1. Rotate the shaft so the reference “AB” on the must be:
flywheel disc or the circumference of the
drive shaft flange (against the flywheel) is in Measurement Models Driveshaft
the 12 o’clock position shown on figure# 7. JU4H-10,12,
2. Measure from the rear face of the flywheel 60 + 1mm. 14,20,22,24 SC41
drive disc or the drive shaft flange to point A. JU4H-UFAB26 SC41A
(Point A is on the bearing bore as shown in JU4R-09,
Figure 7, on the instrument panel side of the 11,13,19,21,23
engine). This measurement must be: JU4H-28,30,32,34,40,
Measurement Models Driveshaft 42,44,50,52,54, SC55
JU4H-10,12, 71 + 1mm. H8,H0,H2, 58, 84 SC55A
58 + 2mm. 14,20,22,24 SC41 JU4R-40,49,51,53
JU4H-UFAB26 SC41A JU6H-UFDO,D2,
JU4R-09, 70.5 + 1mm. 30,32,34,G8,M8,
11,13,19,21,23 M2,58,50,52,54 SC55L-A
JU4H- JU6H-ABL8,L0,L2,
28,30,32,34,40, SC55 54
68 + 4mm. 42,44,50,52,54, SC55A 86.5 + 1mm. JU6H-UF68,60,62, SC61L-A
H8,H0,H2, 58, 84 84, JU6H-AB76,84
JU4R-40,49,51,53 78 + 1mm. All JU6 & JW6 SC2130
68 + 1.5mm. JU6H-UFDO,D2, 91 + 1mm. All JU6 & JW6 SC2130A
30,32,34,G8,M8, 112.5 + 1mm. All JW6 SC81A
M2,58,50,52,54 SCSC55L-A
JU6H-UFABL0, D) With the driveshaft in the same orientation as the
L2, L8 previous step (Step C), check the Vertical
84 + 1.5mm. JU6H-UF68, 60, 62, alignment of the shafts.
84, SC61L-A 1. Measure the front face of the drive shaft
JU6H-UFAB76,84 flange on the pump end to point D. (Point D
76 + 3mm. All JU6 & JW6 SC2130 is the same as point B, with the driveshaft
89 + 3mm. All JU6 & JW6 SC2130A rotated 90). The measurement must be equal
109 + 2mm. All JW6 SC81A to the measurement at point C + 1 mm.

B) With the driveshaft in the same orientation as the Re-install all guards and grease fittings before
previous step (Step A), check the Horizontal reconnecting the battery cables.
Angular alignment of the shafts.

Page 14 of 41
 weekly test.

NOTE: This engine is designed to operate at rated

load conditions. For testing purposes the engine can
be run at lower load (lower flow) conditions.
Running times in any one period should not exceed
30 minutes maximum.

Before starting the engine make sure of the

following:

1) The operator has free access to stop the

Figure #7 engine in an emergency.
2) The plant room ventilation ducts are open
and the engine has good access for air.
3) All the guards are in position and, if not, for
whatever reason, any rotating parts will be
free and clear without restriction.
4) Battery covers are in place and there is
nothing on top of or touching the engine,
which is not part of the original supply
specification.
5a) Heat Exchanger Cooling: The water supply
for coolant is available again without
restriction.
5a) Radiator Cooling: The air supply for cooling
Figure #8 is available again without restriction.

DRIVESHAFT MAINTENANCE When engine is running make sure that the coolant
temperature and oil pressure raw cooling water flow
1. To service the driveshaft disconnect the are within the limits specified on the relevant
negative battery cables, remove the top of Installation & Operation Data Sheet in the Technical
guard and set aside. Catalog, C13965.
2. Rotate engine shaft manually so the u-joint
grease fittings are accessible. If the coolant temperature is excessive, check:
3. Using a hand held grease gun with N.L.G.I. a) Cooling loop strainers
grade 1 or 2 grease position on grease fitting. b) Proper functioning of thermostat
Pump with grease until grease is visible at all c) Condition of heat exchanger tube bundle
four cap seals.
4. Verify all driveshaft connecting bolts remain 2.6 STARTING/STOPPING THE ENGINE
tight. Re-torque per 2.4.1 if necessary.
5. Reinstall top of guard and connect negative Special Notes to Equipment Installer of an LPCB
battery cables. Approved (LPS1239) Engine Model:

2.4.3 Other Coupling Types Any device fitted to the engine or controller, which
Consult Factory or Clarke website at could prevent the engine starting automatically, shall
www@clarkefire.com for additional return automatically to the normal position after
information. manual application. The electrical fuel shutoff
actuator shall be connected to an Engine Stop button
2.5 WEEKLY TEST on the main pump controller.

An experienced operator should be present during the

Page 15 of 41
The main pump controller shall de-energize the start Note: On JW Engines you can also start engines
motor when the engine has achieved 700-1000 rpm. using manual starting contactors.
On LPCB engines, use main pump controller for
To Start Engine: starting and stopping the engine. Should the main
pump controller become inoperable, the engine can
Use main pump controller for starting. Follow be manually started from the engine gauge panel.
instructions provided by controller manufacturer. For manual starting of an engine with a gauge panel.
(Refer to Figure #9A): Lift and hold MANUAL
On UL/FM engines, use main pump controller for CRANK #1, until engine starts, or release after 15
starting and stopping the engine. Should the main seconds. If unit fails to start, wait for 10 seconds, use
pump controller become inoperable, the engine can MANUAL CRANK #2 and repeat step. If
be manually started and stopped from the engine COOLING WATER is not flowing or engine
gauge panel. For manual starting and stopping of an TEMPERATURE is too HIGH, open cooling
engine with a gauge panel: Position MODE system manual by-pass valves (applies to heat
SELECTOR to MANUAL RUN. (Refer to Figure exchanger cooled engines only).
#9). Lift and hold MANUAL CRANK #1, until
engine starts, or release after 15 seconds. If unit fails
to start, wait for 15 seconds, use MANUAL CRANK
#2 and repeat step. If COOLING WATER is not
flowing or engine TEMPERATURE is too HIGH,
open cooling system manual by-pass valves (applies
to heat exchanger cooled engines only).

Page 16 of 41
 UL/FM Instrument Panel

Figure #9

1 – Emergency Operating Instructions 4 – Overspeed Reset

2 – Automatic-Manual Mode Selector 5 – Warning Light
3 – Manual Crank Controls 6 – Overspeed Verification

Page 17 of 41
 LPCB Instrument Panel

2
2

Figure #9A

1 – Emergency Operating Instructions

2 – Manual Crank Controls

IMPORTANT: Main pump controller selector main pump controller and engine gauge panel to
should be in the OFF position when starting from AUTOMATIC after completing manual run.
engine gauge panel. Be sure to return selector on 2.6.3 To Stop Engine

Page 18 of 41
If engine is started from main pump controller use 3.1.1.1 JU4/6-UF,NL Engine Series:
main pump controller to stop the engine.
1) Loosen the air bleed vent screw (A) two full
If engine is started from engine gauge panel: Return turns by hand on fuel filter base. Ref. Figure
MODE SELECTOR switch to #11
AUTOMATIC/MANUAL STOP position, engine 2) Operate supply pump primer lever (B) until
will stop. Close cooling system manual by-pass fuel flow is free from air bubbles. Ref.
valve if opened. Figure #12.
3) Tighten bleed plug securely; continue
IMPORTANT: DO NOT leave the MODE operating hand primer until pump action is
SELECTOR switch in the MANUAL RUN position not felt. Push hand primer inward (toward
during AUTOMATIC operation. (The controller engine) as far as it will go.
will be unable to stop the engine and DAMAGE 4) Start engine and check for leaks.
MAY RESULT).

Engines not equipped with an engine gauge panel,

and LPCB engines, have a manual shutdown lever
on the engine for shutdown. A
3.0 ENGINE SYSTEMS

3.1 FUEL SYSTEM

3.1.1 Bleeding the Fuel System

CAUTION: Escaping fluid under pressure can

penetrate the skin causing series injury. Relieve
pressure before disconnecting fuel or other lines.
Tighten all connections before applying pressure. Figure #11
Keep hands and body away from pinholes and
nozzles, which eject fluids under high pressure.
Use a piece of cardboard or paper to search for
leaks. Do not use your hand.
If ANY fluid is injected into the skin, it must be
surgically removed within a few hours by a doctor
familiar with this type injury or gangrene may
result. Doctors unfamiliar with this type of injury
may call the Deere & Company Medical
Department in Moline, Illinois, or other
knowledgeable medical source. Ref figure #10

B
Figure # 12

If engine will not start, it may be necessary to bleed

air from fuel system at fuel injection pump or
Figure #10 injection nozzles as explained next.

Whenever the fuel system has been opened up for

service (lines disconnected or filters removed), it will
be necessary to bleed air from the system.

Page 19 of 41
At Fuel Injection Pump: 3.1.1.3 JDFP/JW6 Engine Series:

1) Slightly loosen fuel return line connector (A) Refer to Figure #19 for system components location.
at fuel injection pump. Ref figure #13
2) Operate fuel supply pump primer lever until A – Primary Fuel Filter
fuel, without air bubbles, flows from fuel B – Secondary Fuel Filter
return line connection. C – Fuel Injection Pump
3) Tighten return line connector at 16N-m (12 D – Speed Adjustment
lb-ft).
4) Leave hand primer in the inward position At Round Primary Fuel Filter/Water Separator:
toward cylinder block. Ref. Figure #14.
1) Drain water and contaminants from clear
sediment bowl.
2) Loosen air bleed vent screw (A) on fuel filter
base (Figure# 15)
A 3) Operate and primer (B) until fuel flow is free
from air bubbles (Figure#15)
4) Tighten vent screw as hand primer is held in
downward pumping position.

Figure # 13

Figure # 15

At Rectangular Final Fuel Filter:

1) Loose bleed plug (A) on fuel filter base

(figure#16).
2) Operate hand primer (B) on fuel supply
pump (figure#17), until a smooth flow of
Figure #14 fuel, free of bubbling, comes out of the plug
hole.
3.1.1.2 JU4/6 LP Engine Series 3) Simultaneously stroke the hand primer down
and close the filter port plug. This prevents
air from entering the system. Tighten plug
Photo to follow later securely. DO NOT over tighten.
4) Start engine and check for leaks.

Page 20 of 41
 A
A

Figure #16 Figure #18

D
B B
A
C

Figure #17 Figure #19

If engine will not start, it may be necessary to bleed 3.1.2 Draining the Condensate from the Fuel Filter
air from fuel system at injection nozzles as explained
below. Drain the condensate from the fuel filter. Fuel filters
have a drain (B) located at the bottom of their body
At Fuel Injection Nozzle (A) figure#20, these filters should be drained each
week to relieve built up water.
1) Loosen fuel line connection at no. 1 injection
nozzle (A) (figure#18)
2) Crank engine with starting motor (but do not
start engine), until fuel free from bubbles
flows out of loosened connections. Retighten
connection.
3) Start engine and check for leaks.
4) If engine does not start, repeat procedure at
remaining injection nozzles (if necessary)
until enough air has been removed from fuel
A
system to allow engine to start.

B
Figure #20

Page 21 of 41
3.1.3 Changing the Fuel Filter Cartridges 8) Install retaining ring onto mounting base
making certain dust seal is in place on filter
Changing the cartridges and bleed any air from the base. Hand tighten ring (about 1/3 turn) until
fuel system as per instructions given in section 3.1.1. it “snaps” into the detent. DO NOT over
Fuel filter changes should take place as per tighten retaining ring.
recommendations and only using approved filters. It
may also be necessary to change filters out with the Note: The proper installation is indicated when a
recommendations in the event of: “click” is heard and a release of the retaining ring is
felt.
1) The engine has had an overhaul.
2) The quality of the fuel is questionable. A plug is provided with the new element for plugging
3) The engine has been subjected to temporary the used element.
adverse conditions outwith it normal
operating parameters. 9) Open fuel shut-off valve and bleed the fuel
4) The fuel tank condensation trap has not been system. Tighten bleed plug (D). Reference
drained in line with manufacturer’s Figure #21
recommendations.

3.1.3.1 JU4/6-UF,NL Engine Series

D
1) Close fuel shut-off valve, if equipped
2) Thoroughly clean fuel filter assembly and
surrounded area. A
3) Loosen drain plug (C) and drain fuel into a
suitable container. Ref figure#21

Note: Lifting up on retaining ring and rotate it helps

to get past raised locators.

4) Firmly grasp the retaining ring (A) and rotate B

it counterclockwise ¼ turn. Remove ring C
with filter element (B). Ref figure#21 Figure #21
5) Inspect filter mounting base for cleanliness.
Clean as required. 3.1.3.2 JU4/6 LP Engine Series

Note: Raised locators on fuel filter canister must be 3.1.3.3 JDFP/JW6 Engine Series
indexed properly with slots in mounting base for
correct installation. Each engine has two fuel filters. For the purpose of
identity, the primary filter incorporates the
6) Install new filter element onto mounting transparent water separator.
base. Be sure element is properly indexed
and firmly seated on base. It may be Replacing (round) Primary Fuel Filter/Water
necessary to rotate filter for correct Separator
alignment.
1) Close fuel shut-off valve at bottom of fuel
If equipped with water separator, remove filter tank, if equipped.
element from water separator bowl. Drain and clean 2) Thoroughly clean fuel filter/water separator
separator bowl. Dry with compressed air. Install assembly and surrounding area.
water separator bowl onto new element. Tighten
securely. Note: Lifting up on retaining ring (F) as it is rotated
helps to get it past retaining dent. Ref. Figure #22
7) Align keys on filter element with slots in
filter base.

Page 22 of 41
 3) Rotate retaining ring counterclockwise ¼ Note: Keep a small container under drain plug to
turn. Remove ring with filter element. catch draining fuel.
4) Remove water separator bowl (G) from filter
element (E). Drain and clean separator bowl. 3) With fuel filter firm against base, lift up on
Dry with compressed air. Ref. Figure #22 top retaining spring and pull down on bottom
Note: Notice raised locators on filter element. These retaining spring. Pull fuel filter off guide
locators insure proper alignment of filter element to pins of fuel filter base and discard.
filter base. 4) Install new fuel filter onto guide pins of fuel
5) Install water separator bowl onto new filter filter base. Hold filter firmly against base.
element. Tighten securely. 5) Secure bottom filter retaining spring first,
6) Index filter element until longer, vertical then secure top retaining spring (four
locator (D) is oriented opposite mounting arrows).
base. Insert filter element into base securely. 6) Install new drawn plug, shown installed.
It may be necessary to rotate filter for correct Tighten bleed plug and drain plug securely.
alignment. Ref. Figure #22 Do not over tighten.
7) Install retaining ring to filter base, making 7) Open fuel shut-off valve and bleed the fuel
certain dust seal (C) is in place on filter base. system. Ref. Figure #23
Tighten retaining ring until it locks into
detent position and a “click” sound can be
heard. Ref. Figure #22
8) Bleed fuel system.
C

Figure #23

3.1.4 Fuel Tanks

Keep the fuel tank filled to reduce condensation to a

minimum. Open drain at the bottom of the fuel tank
once a week to drain off any possible water and/or
sediment. Fill tank after each test run.

Note: Per NFPA 25 standards, the fuel tank level

Figure #22 must never be less than 67% of its capacity.

Replacing (rectangular) Secondary Fuel Filter 3.1.5 JU4/6 Fuel Injection Pump Components
Element
THIS TAG IS SUPPLIED ON ALL JU4 AND JU6
1) Close fuel shut-off valve at bottom of fuel ENGINES
tank, if equipped.
2) Loosen bleed plug (C) on side of filter base.
Remove drain plug (B) to drain from fuel
filter. Ref. Figure #23

Page 23 of 41
 JU6H-UF30
JU6H-UFD0
JU6H-UFG8
JU6H-UFABL0
JU6H-UFABL2
JU6H-UFABL8
JU6H-UFM8 13558
JU6H-UFM0
JU6H-UF58
JU6H-UF50
JU6H-UF68
JU6H-UF60
JU6H-LP50
The above tag is stamped to identify the “As JU6H-LP60
JU6H-UF32
Built” Components. Refer to the next two tables JU6H-UFD2 13563
to identify: JU6H-UFM2 or
Table 1) Droop Spring Part Number by Engine JU6H-UF52 C02353
JU6H-UF62
Model and Speed.
JU6H-UF34
Table 2) Run-Stop Solenoid (Internal to Injection JU6H-UF54 24339
Pump) Part Number by engine voltage. JU6H-UF84
Injection Pump JU6H-UFAB54
“Droop Spring” Part Number JU6H-UFAB76
JU6H-UFAB84
RPM 1760 2350 2800
2100 2600 2960 Run-Stop Solenoid Part Number
2350 3000 ETR ETS
MODEL 12 Volt SD26214 or SD26921 or
JU4H-UF10
C07853 C07827
JU4R-UF09
JU4R-UF11 13563 24 Volt SD26387 or SD26922 or
JU4H-UF20 or C07826 C07828
JU4R-UF19 C02353 Legend:
JU4R-UF21 ETR – Energized to Run
JU4H-LP20
JU4R-UF23 ETS – Energized to Stop
JU4R-UF13 SD # - Stanadyne Part Number
JU4H-UF14 24339 C # - Clarke Part Number
JU4H-UF24
JU4H-UFAB26
3.1.6 JW6 Fuel Injection Pump Components
JU4H-UF12
JU4H-UF22
JU4H-UF32 13563 For Droop Spring and Run-Stop Solenoid (external to
JU4H-UF42 or Injection Pump) part numbers consult factory.
JU4R-UF51 C02353
JU4H-UF52
JU4H-UFH2
3.2 AIR/EXHAUST SYSTEM
JU4H-UF34
JU4H-UF44 3.2.1 Ambient Conditions
JU4H-UF54
JU4R-UF53 24339 Clarke engines are tested in accordance with SAE
JU4H-LP54
JU4H-LPL4 J1349 (Clarke USA) or ISO 3046 (Clarke UK). In
JU4H-UF84 this capacity they may be derated to meet certain site
JU4H-UF30 conditions, failure to do so can seriously impede the
JU4H-UF40 performance of the engine and could lead to
JU4R-UF40
premature failure.
JU4H-UF50
JU4H-UFH8 20357
JU4H-UFH0 3.2.2 Ventilation
JU4H-UF58
JU4R-UF49
JU4H-LP50

Page 24 of 41
The engine must be provided with adequate
ventilation to satisfy the requirements of the
combustion system, radiator cooling systems where
fitted, and allow adequate dissipation of radiated heat
and crankcase emissions. For all this data refer to
Installation & Operation Data in Technical Catalog,
C13965. This data can be used for proper sizing of
inlet and outlet louvers.

3.2.3 Standard Air Cleaner

The standard air cleaner is a reusable type. Should a

situation occur where the air cleaner becomes
plugged with dirt (starving the engine of air), loss of
power and heavy black smoke will result; the air
cleaner should be serviced immediately. See figure
#39 for air cleaner part numbers by Clarke Engine
Model.

CAUTION: Do not attempt to remove the air

cleaner while an engine is running nor run the engine
while the air cleaner is off. Exposed components
could cause severe injury to personnel and major
internal engine damage could occur should any
foreign matter be drawn into the engine.

The air cleaner manufacturer recommends the

following:
1. The pre-oiled reusable elements are serviced
with a special oil. The elements can be
serviced or replaced.
2. Figure #24 shows the air filter service
instructions.
3. When servicing the element is not practical,
you can improve filter efficiency by re-
spraying with oil.

NOTE: Do not attempt this while engine is running

NOTE: Do not over oil the reusable element

Page 25 of 41
 JU4-LP50, 54, L4 & JU6 All

Figure #24

Figure #27 JDFP/JW6

3.2.4 Crankcase Ventilation
3.2.4.2 Crankcase Ventilation System
3.2.4.1 Open Crankcase Ventilation (Refer to
A crankcase ventilation system allows for the
fig#27b)
recirculation of vapors (expelled through a vent pipe
attached to the rocker cover breather element) to the
Vapors which may form within the engine are
combustion air inlet. Refer to figure 27a.
removed from the crankcase and gear train
compartment by a continuous, pressurized ventilation
system.

A slight pressure is maintained within the engine

crankcase compartment. Vapors expelled through a
vent pipe attached to the rocker cover breather
element. Ref. Figure #25, 26, & 27.

Figure #27a

Engine Open Crankcase Crankcase

Model Ventilation Ventilation System
JU4R-UF09
JU4H-UF10
JU4R-UF11
Figure #25 JU4H-UF12
JU4H-UF14
JU4-UF10, 12, 20, 22, JU4-LP20, 24 JU4R-UF19
JU4H-UF20
JU4H-LP20
JU4R-UF21
JU4H-UF22
JU4R-UF23
JU4H-UF24
JU4H-UFAB26
JU4H-UF30
JU4H-UF32
JU4H-UF40
JU4R-UF40
JU4H-UF42
JU4R-UF49
JU4H-UF50
Standard Optional
Figure #26 JU4H-LP50
JU4-UF30, 32, 40, 42, 50, 52, H8, H0, H2, 58 JU4R-UF51

Page 26 of 41
JU4H-UF52 • Adequate supports to prevent strain on the
JU4H-UF58 engine exhaust outlet and minimize
JU4H-UFH2
JU4H-UFH8 vibration.
JU4H-UFH0 • Protection against entry of water and other
JU6H-UF30 foreign matter.
JU6H-UF32
JU6H-UF50
JU6H-LP50 While the engine is running inspect exhaust pipe
JU6H-UF52 outlet outside of the pump room itself for
JU6H-UF58 environmental hazards such as excessive smoke
JU6H-UF62 conditions. The following could be used as a guide
JU6H-UF68
JU6H-UF60
for general engine operating conditions.
JU6H-LP60
JU6H-UFD0 1) Blue Smoke – Possible engine oil
JU6H-UFG8 consumption.
JU6H-UFABL0
JU6H-UFABL2
JU6H-UFABL8 2) White Smoke – Possibility of water in
JU6H-UFM8 Standard Optional cylinders, water in fuel or internal engine
JU6H-UFM0 problem.
JU6H-UFD2
JU6H-UFM2
3.3 LUBRICATION SYSTEM
Figure #27b
3.3.1 Checking Sump Oil
Engine Open Crankcase
Model Crankcase Ventilation Check the sump oil level using the dipstick on the
Ventilation System engine as shown in Figure #28 &29.
JU4H-UF34
JU4H-UF44 This level must always be between the dipstick marks
JU4H-UF54 Min. and Max. with the engine not running.
JU4R-UF53
JU4H-LP54
JU4H-LPL4 Standard Standard
JU4H-UF84
JU6H-UF34
JU6H-UF54
JU6H-UF84
JU6H-UFAB54
JU6H-UFAB76
JU6H-UFAB84

Figure #27b cont’d

3.2.5 Exhaust System Figure #28

JU4/6
Excessive back pressures to the engine exhaust can
considerably reduce both engine performance and
life. It is therefore important that exhaust systems
should be the proper diameter and be as short as
possible within the minimum amount of bends. Refer
to Installation & Operating Data in Technical Catalog
C13965 for exhaust data.

The installation of the exhaust system should consist

of the following:
• Personnel protection from hot surfaces.

Page 27 of 41
 9. Operate the engine and check for leakage
from the filter. When the engine has cooled,
check the oil level on the dipstick and put
more oil into the sump, if necessary.
10. Return the unit back into service by returning
the main pump controller selector to
“automatic” position and the manual
operating lever to AUTO-OFF position.

Figure #29
JDFP/JW6

3.3.2 Changing Engine Oil

1) Operate the engine until it is warm.

2) Stop the engine. Remove the sump drain
plug and drain the lubricating oil from the
sump. Fit the drain plug tighten the plug to
34 Nm (25lbf-ft) / 3.5 kgf-m. Figure #30
3) Fill the sump to the ‘FULL” mark on the
dipstick with new and clean lubricating oil of
an approved grade.
4) Return the unit back into service by returning 3.3.4 Oil Specification
the AEC selector to “automatic” position and
the manual operating lever to manual stop This engine is factory-filled with John Deere
position. Engine Break-in Oil.
5) Dispose used oil properly.
Important: Do not add makeup oil until the oil
3.3.3 Changing Oil Filter Cartridge level is BELOW the add mark on the dispstick.

1. Turn engine off. Break-in period is 1 year from engine start-up.

2. Put a tray under the filter to retain spilt
lubricating oil. Low Speed engine models (Nameplate RPM is less
3. Remove the filter with a strap wrench or than or equal to 2600 RPM) are shipped from Clarke
similar tool. Then dispose of the filter with John Deere Break-in oil installed. Break-In Oil
properly (Ref Figure #30). (TY22041, 10W30) should be used to make up any
4. Clean the filter head. oil consumed during the break-in period.
5. Add clean engine lubricating oil to the new
filter. Allow the oil enough time to pass High speed engine models (Nameplate RPM is
through the filter element. greater than 2600 RPM) are shipped with CI-4,
6. Lubricate the top of the filter seal with clean 15W40 oil. On these models any make up oil should
engine lubricating oil. meet the requirements of CF-4, CG-4, CH-4, or CI-4,
7. Fit the new filter and tighten it by hand only. Viscosity Grade 15W40.
Do not use a strap wrench.
8. Ensure that there is lubricating oil in the Oil spec to be used after break-in period, all engine
sump. On turbocharged engines, ensure that models:
the engine will not start and operate the
starter motor until oil pressure is obtained.

Page 28 of 41
 Water can produce a corrosive environment in the
cooling system, and the mineral content may permit
scale deposits to form on internal cooling surfaces.
Therefore, inhibitors must be added to control
corrosion, cavitation, and scale deposits.

Chlorides, sulfates, magnesium and calcium are

among the materials which make up dissolved solids
that may cause scale deposits, sludge deposits,
corrosion or a combination of these. Chlorides
Figure #31 and/or sulfates tend to accelerate corrosion, while
hardness (percentage of magnesium and calcium salts
3.3.5 Oil Capacities (Including Filter) broadly classified as carbonates) causes deposits of
ENGINE OIL CAPACITY scale. Water within the limits specified in figure #33
MODEL QUARTS (LITERS) is satisfactory as an engine coolant when properly
JU4 – All Models 14.3 (13.5) inhibited. Use of distilled water is preferred.
JU6 – All Models 20.1 (19)
JW6 – All Models 30.1 (28.5) Grains
Figure #32 Parts per per
Materials Million Gallon
3.4 COOLING SYSTEM Chloride (Max.) 40 2.5
Sulfates (Max.) 100 5.8
3.4.1 Engine Coolant Total Dissolves Solids
(Max.) 340 20
The following information is provided as a guide for Total Hardness (Max.)
John Deere Engine users in the selection of a suitable 170 10
coolant. Figure #33
The water/ethylene glycol/inhibitor coolant mixture 3.4.3 Coolant Capacities
used in John Deere engines must meet the following
basic requirements: Use an ethylene glycol coolant (low silicate
• Provide for adequate heat transfer. formulation) that meets the standard of either the GM
• Provide protection from cavitation damage. 6038-N formulation (GM1899-M performance) or
• Provide a corrosion/erosion-resistant ASTM D4985 requirements.
environment within the cooling system.
• Prevent formation of scale or sludge deposits A 50% coolant water solution is recommended. A
in the cooling system. concentration over 70% is not recommended because
• Be compatible with engine hose and seal of poor heat transfer capability, adverse freeze
materials. protection and possible silicate dropout.
• Provide adequate freeze and boil over Concentrations below 30% offer little freeze, boil
protection. over or corrosion protection.

WARNING IMPORTANT
A water and anti-freeze solution is required for Never use automotive-type coolants (such as those
pump installations. Premixing this solution prior meeting only ASTM D3306 or ASTM D4656).
to installing is required. This prevents possible These coolants do not contain the correct additives
pure anti-freeze chemical reactions to block to protect heavy-duty diesel engines. They often
heater elements which can burnout the element. contain a high concentration of silicates and may
Please see the technical data section for proper damage the engine or cooling system.
cooling system capacities of each model. ENGINE COOLANT CAPACITY
MODEL QUARTS (LITERS)
3.4.2 Water JU4H-All Models 15 (14.2)
JU4R- All Models 20 (19)

Page 29 of 41
 JU6H-All Models 20 (19)
JDFP-06WA/JW6-UF30 22 (21) 3.4.5 Procedure for Filling Engine
JDFP-06WR/JW6-UF40 23 (22)
JW6-UF50, 60 23 (22) During filling of the cooling system, air pockets may
Figure #34 form. The system must be purged of air prior to
being put in service. This is best accomplished by
3.4.4 Coolant Inhibitor filling with a pre-mix solution.

The importance of a properly inhibited coolant Caution: Do not overfill cooling system.
cannot be over-emphasized. A coolant which has A pressurized system needs space for heat
insufficient or no inhibitors at all, invites the expansion without overflowing.
formation of rust, scale, sludge and mineral deposits.
These deposits can greatly reduce the cooling 3.4.5.1 Engines without Coolant Recovery Tank
systems efficiency and protection capabilities. (Figure #35A)

Recommended supplemental coolant inhibitors are a Install the pressure cap, start and run engine for
combination of chemical compounds which provide approximately 5 minutes in order to purge the air
corrosion protection, cavitation suppression, pH from the engine cavities.
controls and prevents scale. These inhibitors are
available in various forms, such as liquid packages or When verifying that the coolant is at a safe operating
integral parts of anti-freeze. level, it is best to wait until the engine temperature
drops to approximately 120ºF (49ºC), or lower,
It is imperative that supplemental inhibitors be added before removing the pressure cap.
to all John Deere engine systems. A pre-charge
dosage must be used at the initial fill and the Remove the pressure cap and refill to the proper fill
maintenance dosage used at each service interval. level. To continue the deaeration process start and
Serious damage will occur unless inhibitors are used. run engine until the temperature stabilizes at
Some of the more common corrosion inhibitors are approximately 160°-200° (71°-93° C) or run engine
borates, nitrates and silicates. for 25 minutes, whichever is longer. During this
Inhibitors become depleted through normal warming process, you may see coolant coming from
operation; additional inhibitors must be added to the the overflow tube attached at the pressure cap
coolant as required to maintain original strength location. Allow engine to cool, then remove the
levels. Refer Figure #35 for proper concentrations of pressure cap and refill to the proper fill level.
inhibitors.
Min. Max Caution: Do not remove pressure cap while coolant
PPM PPM is at normal operating temperatures. Possible
Boron (B) 1000 1500 personal injury could result from the expulsion of hot
Nitrite (NO2) 800 2400 coolant.
Nitrates (NO3) 1000 2000
Silicon (Si) 50 250
Phosphorous (P) 300 500
PH 8.5 10.5
Figure #35

Do not use soluble oils or chromate inhibitors in John

Deere engines. Detrimental effects will occur.
To properly check inhibitor concentrations it may be
necessary to contact your local Service/Dealer for
assistance. Refer to Parts Information Section to
obtain the part number for the factory Coolant
Analysis Kit. This kit can be purchased for a
nominal fee for analyzing the conditions of the
engine’s coolant.

Page 30 of 41
 Note: Use a fill rate of no more than 10 liters/min (3
gpm). Replace heat exchanger pressure cap.

Cap

Heat Exchanger

Coolant
Recovery Tank

Figure #35B

Remove cap from coolant recovery tank and fill the

coolant recovery tank with a 50/50 coolant mixture to
a level of 100mm (4”) from bottom of the tank.
Replace cap.

Figure #35C

Start and run engine with fire pump in a no flow or

low flow condition. Run engine for approximately 1
minute. Carefully remove heat exchanger pressure
cap while engine is running.

Note: Caution should always be taken when

removing a cap from a system under pressure.

Refill cooling system to the pressure cap sealing

surface. Replace heat exchanger pressure cap.

Complete deaeration will take several warm up/ cool

down cycles. Always check appropriate coolant level
in coolant recovery bottle.

3.5 ELECTRICAL SYSTEM

Figure #35A

3.4.5.2 Engines with Coolant Recovery Tank

(Figure #35B & #35C)

Remove pressure cap from heat exchanger and fill

the cooling system with a 50/50 coolant mixture to
pressure cap sealing surface.

Page 31 of 41
3.5.1 Wiring Diagrams (Only with Engine Gauge B
Panel)
Run/Stop Drawing Description Reference
Solenoid No. (DC Voltage) Document
NFPA-20 and A
UL/FM
ETR C07575 engine gauge
(JU4/6) panel
(NL Models -
Optional) See
Technical A
NFPA-20 and Catalog Figure #37
UL/FM C13965
ETR C07602 engine gauge To adjust Belt Tension:
(JW6) panel Check belt tension:
(NL Models - - Give at arrow must be .4” - .6” (10-15mm).
Optional) To increase tension of the water pump driving belts:
- Loosen alternator or belt tensioner mounting
LPCB bolts A and B.
ETS U071016 Engine Gauge - Adjust to proper belt tension.
Panel - Tighten mounting bolts A and B.

ETR = Energized to Run 3.5.3 Speed Switch (when supplied)

Drawing No. Description Reference In the event of an engine overspeed, the speed switch
(AC Voltage) Document signals the main pump controller and also affects an
C07591 NFPA-20, engine shutdown. The OVERSPEED RESET
(JU4/6) UL/FM, and LPCB (figure# 9) switch is included on the instrument
Engine Jacket panel. Should an overspeed condition occur,
Water Heater investigate the cause and make necessary corrections
(NL Models - See Technical before placing engine back in service. The
Optional) Catalog OVERSPEED RESET must be manually lifted to
C13965 reset.
Optional Engine NOTE: This reset operation must be
C07651 Jacket Water completed to allow a restart. If not, the
(JDFP/JW6) Heater engine will not start thru the main pump
(NL Models - controller or manually.
Optional)
Figure #36 OVERSPEED VERIFICATION

3.5.2 Checking Drive Belt Tension and Adjustment Hold the OVERSPEED VERIFICATION switch in
the “up” position. This will provide the main pump
All drive belts must be adequately tightened to secure controller with an overspeed signal and engine
that both the engine water pump and battery charging shutdown at 67% of the set overspeed RPM.
alternator (when fitted) are operating efficiently.
Refer to Figure #37. Start the engine via the main pump controller; the
B speed switch will generate an overspeed signal and
shutdown protecting both the engine and pump.

EXAMPLE
Rated Speed: 1760 RPM
Overspeed Shutdown: 2112 RPM (120% of
1760 RPM)

Page 32 of 41
 Verification Shutdown: 1410 RPM (67% of
2112 RPM)

CAUTION-after verification of overspeed, lift the

OVERSPEED RESET switch and reset the main
pump controller to re-instate normal operation of the
engine and speed switch.

3.5.4 Magnetic Pick-Up (when supplied)

A magnetic pick-up, mounted in the flywheel

housing, provides the input signal for the tachometer Figure #38
overspeed switch, and/or the main pump controller.
There should be a 0.03" air gap between the top of 4.0 MAINTENANCE SCHEDULE
the ring gear and the center of the magnetic pick-up.
With one tooth centered in the magnetic pick-up hole, 4.1 ROUTINE MAINTENANCE
thread the pickup in until it touches the gear tooth
and then back it out 1/2 turn. Tighten jam nut while NOTE: The following Routine Maintenance schedule
holding the pickup in position. Reconnect to wiring is based on an engine usage rate not exceeding 2
harness. hours per month. For UL/FM engine models, also
refer to NFPA25.
3.6 ENGINE SPEED ADJUSTMENT LEGEND:
‰ Check
A mechanical governor controls the engine speed. ™ Clean
The governor is built into the fuel injection pump. All ¾ Replace
governors are adjusted to the rated speed at o Lubricate
nameplate power or maximum allowed pump load WEEKLY
before leaving Clarke. During Start-Up Inspection or ‰ Air Cleaner
when placing reconditioned units into service, some ‰ Battery
minor speed adjustment may be required. It is ‰ Coolant Hoses
recommended that this adjustment be performed by ‰ Coolant Levels
the authorized Service Dealer representative. ‰ Cooling Water Solenoid Valve
‰ Exhaust System
To adjust the speed of the engine: ‰ Fuel Tank
‰ General Inspection
A. Start the engine by following the “To Start ‰ Governor Run-Stop Control
Engine” Procedure in this manual. ‰ Jacket Water Heater
B. Let the engine warm-up. Loosen the jam ‰ Lubrication Oil Level
nut(s) (Figure #38). ‰ Operating Gauges
C. While observing the instrument panel tach ‰ Remove Water from Fuel Filter
rotate the long adjustor clockwise to lower ‰ Run Engine
the RPM and counter clockwise to raise the ‰ Warning Light
RPM’s until desired speed is obtained. Ref. ‰ Radiator Core Debris
Figure #38. EVERY 6 MONTHS
D. Holding secure the long adjustor with a ™ Batteries
wrench tighten the jam nut. ‰ Battery Charging Alternator
E. Stop engine by following “To Stop Engine” ‰ Belts
Procedure in this manual. ™ Cooling Water Strainers
‰ Driveshaft U-Joints
‰ Fuel Lines
EVERY 1 YEAR
™ Air Cleaner
‰ Coolant Inhibitor

Page 33 of 41
 ‰ Crankcase Vent System • Phone USA: (513) 719-2352 (calling within USA)
o Driveshaft U-Joints • Phone UK: (44) 1236 429946 (calling outside USA)
¾ Fuel & Oil Filters • Fax USA: (513) 771-0726 (calling within USA)
‰ Heat Exchanger Electrode • Fax UK: (44) 1236 427274 (calling outside USA)
¾ Lubricating Oil • E-Mail USA: dgoodfriend@clarkefire.com
‰ Mounting Isolators • E-Mail UK: dmurray@clarkefire.com
‰ Wiring System
EVERY 2 YEARS 6.2 ENGINE MAINTENANCE PARTS LIST
¾ Air Cleaner FUEL FUEL
ENGINE OIL FILTER FILTER AIR
¾ Batteries MODEL FILTER PRIMARY SECONDARY FILTER
¾ Belts JU4R-UF09
¾ Coolant Hoses JU4H-UF10
JU4R-UF11
¾ Coolant JU4H-UF12
¾ Thermostat JU4R-UF19
JU4H-UF20
JU4R-UF21
IMPORTANT: Set main pump controller to “OFF” JU4H-UF22
while servicing engine. Before turning the main JU4H-UF28
JU4H-UF30 C04440 C02359
pump controller to the "OFF" position, check with JU4H-UF32 or or C03249
the maintenance and security supervisors to verify JU4H-UF40 RE59754 RE60021
that all the departments concerned will be alerted of JU4R-UF40
JU4H-UF42
the temporary interruption of their fire protection JU4R-UF49
equipment for normal maintenance or testing. Also, JU4H-UF50
JU4R-UF51
alert the local fire department in the event that the JU4H-UF52
main pump controller is connected by silent alarm to JU4H-UF58
headquarters. When servicing is complete, return JU4H-UFH2
JU4H-UFH8
main pump controller selector to "Automatic" JU4H-UFH0
position and the mode selector on the engine to JU4H-AP50
“Automatic” position. Advise the appropriate JU4R-UF13 C04521 C02549
JU4H-UF14 or or
personnel the engine has been returned to the JU4R-UF23 RE504836 RE62418 C03249
“Automatic”. JU4H-UF24
JU4H-UFAB26
JU4H-LP20 C04440
5.0 TROUBLE SHOOTING JU4H-LP50 or C02533 C03249
RE59754
Consult Clarke Service Dealer or Factory. Service JU4H-LP24 C04521
JU4H-LP54 or C02533 C03249
dealers can be located by going to our website: JU4H-LPL4 RE504836
www.clarkefire.com. JU4H-UF34
JU4H-UF44 C04521 C02550
JU4H-UF54 or or C03249
6.0 PARTS INFORMATION JU4R-UF53 RE504836 RE520842
JU4H-UF84
JU4H-AP54
6.1 SPARE PARTS JU6H-UF30
JU6H-UF32
To ensure best operation and efficiency of all engine JU6H-UF50
JU6H-UF52
components, always use genuine Clarke spare parts. JU6H-UF58
JU6H-UF62
Orders should specify: JU6H-UF68
JU6H-UF60
• Engine Model Number - See Engine General JU6H-UFD0 C04440 C02359
• Engine Serial Number - Specification JU6H-UFABL0 or or C03396
JU6H-UFABL2 RE59754 RE60021
• Part Number(s) Refer to Engine Maintenance JU6H-UFABL8
Parts List section 6.2 or Parts Illustration in JU6H-UFG8
JU6H-UFM8
Technical Bulletin in C13886. JU6H-UFM0
JU6H-UFD2
Contact numbers for spare parts: JU6H-UFM2
JU6H-AP30
• www.clarkefire.com JU6H-AP50

Page 34 of 41
JU6H-AP60 8.2 CLARKE WARRANTY
JU6H-LP50 C04440
JU6H-LP60 or C02533 C03396
RE59754 All Clarke warranted components have warranty
JU6H-LP54 C04521 duration of 12 months beginning at the Start-up date
JU6H-LP84 or C02533 C03396
RE504836 of the fire pump system. The warranty coverage
JU6H-UF34 includes replacement of the part and reasonable cost
JU6H-UF54 of labor for installation. Components failed due to
JU6H-UF84 C04521 C02550
JU6H-UFAB54 or or C03396 improper engine installation, transportation damage,
JU6H-UFAB76 RE504836 RE520842 or misuse is not covered under this warranty.
JU6H-UFAB84
JU6H-AP34
For additional warranty details, see the specific
JU6H-AP54 warranty statement “John Deere New Engine
JU6H-AP84 Warranty” on the following page. Also contact
JW6H-UF30
JW6H-UF38
Clarke direct if you have any questions or require
JW6H-UF40 additional information.
JW6H-UF48
JW6H-UF50
JW6H-UF58 RE57394 RE508633 AR86745 C03244 Clarke is not responsible for incidental or
JW6H-UF60 consequential costs, damage or expenses which the
JW6H-AP30
JW6H-AP40
owner may incur as a result of a malfunction or
JW6H-AP50 failure covered by this warranty.
JW6H-AP60
8.3 JOHN DEERE WARRANTY
ENGINE MODEL Air Filter Air Filter Oil
Service Kit 8.3.1 Warranty Duration
All 99-55050 C121157
Figure #39
Unless otherwise provided in writing, John Deere*
makes the following warranty to the first retail
7.0 OWNER ASSISTANCE
purchaser and each subsequent purchaser (if purchase
is made prior to expiration of applicable warranty) of
Consult Clarke Service Dealer or Factory. Service
each John Deere new off-highway engine marketed
Dealers can be located by going to our website:
as part of a product manufactured by a company
www.clarkefire.com.
other than John Deere or its affiliates:
• 12 months, unlimited hours of use, or
8.0 WARRANTY
• 24 months and prior to the accumulation of 2000
hours of use;
8.1 GENERAL WARRANTY STATEMENT
and on each John Deere engine used in an off-
highway repower application:
The satisfactory performance of Clarke engines and
•12 months, unlimited hours of use.
the goodwill of owners / operators of Clarke engines
Note: In the absence of a functional hourmeter,
are of primary concern to the Engine Manufacturer,
hours of use will be determined on the basis of 12
the Engine Service Dealer and Clarke. All provide
hours of use per calendar day.
support of these products after final installation of the
complete fire pump and sprinkler system.
(*John Deere” means Deere Power Systems Group
with respect to users in the United States, John Deere
Warranty responsibility involves both Clarke and the
Limited with respect to users in Canada, and Deere &
John Deere service organizations worldwide.
Company or its subsidiary responsible for marketing
John Deere equipment in other counties where the
The Engine Manufacturer (John Deere) provides
user is located)
Warranty for the basic engine components and Clarke
provides warranty on the accessories added to meet
8.3.2 Warranty Coverage
the NFPA-20 specifications and FM/UL certification
requirements.
This warranty applies to the engine and to integral
components and accessories sold by John Deere.

Page 35 of 41
All John Deere-warranted parts and components of Note: The hp/kW rating on the engine emissions
John Deere engines which, as delivered to the certification label specifies the gross engine hp/kW,
purchaser, are defective in materials and/or which is flywheel power without fan. In most
workmanship will be repaired or replaced, as John applications this will not be the same rating as the
Deere elects, without charge for parts or engine repair advertised vehicle hp/kW rating.
labor, including reasonable costs of labor to remove
and reinstall non engine parts or components of the Stationary engines under the NSPS provisions are
equipment in which the engine is installed, and, when also covered, including stationary fire pump ratings.
required, reasonable costs of labor for engine Fire pump ratings labeled under the 40 CFR part 60
removal and reinstallation, if such defect appears (NSPS).
within the warranty period as measured from the date
of delivery to the first retail purchaser, if the delivery U.S. EMISSIONS CONTROL WARRANTY
is reported to John Deere within 30 days of the STATEMENT (UNITED STATES ONLY)
delivery.
Emissions control-related parts and components are
8.3.3 Emissions System Warranty (Non-Road warranted by John Deere for five years or 3000 hours
Diesel) of operation, whichever occurs first. John Deere
further warrants that the engine covered by this
EMISSIONS CONTROL SYSTEM warranty was designed, built, and equipped so as to
CERTIFICATION LABEL conform at the time of sale with all U.S. emissions
standards at the time of manufacture, and that it is
WARNING: Statutes providing severe penalties for free of defects in materials and workmanship which
tampering with emissions controls may apply at the would cause it not to meet these standards within the
user’s location. period of five years or 3000 hours of operation,
whichever occurs first.
The emissions warranty described below applies only
to those engines marketed by John Deere that have Warranties stated in this manual refer only to
been certified by the United States Environmental emissions-related parts and components of your
Protection Agency (EPA) and/or California Air engine. For complete engine warranty, less
Resources Board (CARB); and used in the United emissions related parts and components, ref to 8.3.1.
States in equipment. The presence of an emissions
label like the one shown signifies that the engine has COVERED EMISSIONS SYSTEMS AND
been certified with the EPA and/or CARB. The EPA COMPONENTS
and CARB warranties only apply to new engines
having the certification label affixed to the engine System Sample Sub-Systems and Components
and sold as stated above in the geographic areas Air induction system o Air filter housing
o Air mass sensor assembly
governed by the regulation agencies. o Controlled hot air intake system
o Heat riser
o Intake manifold
o Intercooler
o Turbocharger
o Wastegate control assembly valve

Fuel metering o Aneroid

system (fuel system) o Carburetor
o Choke mechanism
o Electronic injection unit
o Fuel injection assembly
o Fuel injection nozzle assembly
o Fuel injection injector
o Fuel injector nozzle
o Fuel injection valve assembly
o Fuel line
o Gas pressure regulator
o Pressure relief valve/assembly
o Air restriction sensor

Page 36 of 41
 o Air temperature sensor Authorized service outlets will use only new or
o Coolant temperature sensor remanufactured parts or components furnished or
o Fuel temperature sensor
o Mass flow module sensor approved by John Deere.
o UEGO sensor Authorized service locations and the name of the
o Throttle John Deere division or subsidiary making this
warranty are listed in the Parts and Service Directory
for John Deere Engines.
Ignition control o Distributor assembly
system o Engine control module At the time of requesting warranty service, the
o Glow plugs purchaser must be prepared to present evidence of the
o Ignition coil date of delivery of the engine.
o Ignition control module
o Ignition sensor
o Ignition wires
John Deere reimburses authorized service outlets for
o Spark plugs limited travel expenses incurred in making warranty
EGR system o EGR cooler service repairs in non-John Deere applications when
o EGR valve body travel is actually per formed. The limit, as of the date
Advanced Oxides of o Lean NOx catalysts of publication of this statement, is US $300.00 or
Nitrogen (NOx o Nox absorbers
controls) o Reductant (urea/fuel)
equivalent. If distances and travel times are greater
containers/dispensing systems than reimbursed by John Deere, the service outlet
Catalyst or thermal o Catalytic converter may charge the purchaser for the difference.
reactor system o Double wall portion of exhaust
system 8.3.5 Warranty Exclusions
o Exhaust manifold
o Exhaust gas recirculation valve
Particulate Controls o Control device enclosure and John Deere’s obligations shall not apply to fuel
manifolding injection pump and nozzles during the pump and
o Regenerators nozzle manufacturer’s warranty period on the pump
o Oxidizers
and nozzles, components and accessories which are
o Traps
o Filters not furnished or installed by John Deere, nor to
o Precipitators failures caused by such items. When the pump
o Manifold absolute pressure (MAP) manufacturer’s warranty is less than the engine
sensor warranty, John Deere will reimburse pump repair
PCV system o Oil filler cap
o PCV solenoid
costs for warrantable-type failures during the
o PCV valve remainder of the original engine warranty period,
o Crankcase ventilation filter when so documented by the pump manufacturer’s
o Crankcase ventilation valve approved service outlet.
Miscellaneous items o Electronic control sensors
used in the above o Electronic control units (ECUs)
systems o ECU software 8.3.6 Purchaser’s Responsibilities
o Pump/valve controllers
o Wiring harness The cost of normal maintenance and depreciation.
o Coolant temperature sensor
o Emissions labels
o Sealing gaskets
Consequences of negligence, misuse, or accident
o Thermocouples involving the engine, or improper application,
o Thermostats installation, or storage of the engine, or improper
o Vacuum-sensitive valve/switches application, installation, or storage of the engine.

8.3.4 Obtaining Warranty Service Consequences of service performed by someone

other than a party authorized to perform warranty
Warranty service must be requested of the nearest service, if such service, in John Deere’s judgment,
authorized John Deere engine service outlet before has adversely affected the performance or reliability
the expiration of the warranty. An authorized service of the engine.
outlet is a John Deere engine distributor, a John Consequences of any modification or alteration of the
Deere engine service dealer, or a John Deere engine not approved by John Deere, including, but
equipment dealer selling and servicing equipment not limited to, tampering with fuel and air delivery
with an engine of the type covered by this warranty. systems.

Page 37 of 41
The effects of cooling system neglect as manifested of profits, loss of crops, rental of substitute
in cylinder liner or block cavitation (“pitting”, equipment or other commercial loss, damage to the
“erosion”, “electrolysis”). equipment in which the engine is installed or for
Any premium for overtime labor requested by the damage suffered by purchaser as a result of
purchaser. fundamental breaches of contract or breach of
Costs of transporting the engine or the equipment in fundamental terms, unless such damages or injuries
which it is installed to and from the location at which are caused by the gross negligence or intentional acts
the warranty service is performed, if such costs are in of the foregoing parties.
excess of the maximum amount payable to the
service location were the warranty service performed 8.3.8 Remedy Limitation
at the engine’s location.
The remedies set forth in this warranty are the
Costs incurred in gaining access to the engine; i.e., purchaser’s exclusive remedies in connection with
overcoming physical barriers such as walls, fences, the performance of, or any breach of guaranty,
floors, decks or similar structures impeding access to condition, or warranty in respect of new John Deere
the engine, rental of cranes or similar, or construction engines. In the event the above warranty fails to
of ramps or lifts or protective structures for engine correct purchaser’s performance problems caused by
removal and reinstallation. defects in workmanship and/or materials, purchaser’s
Incidental travel costs including tolls, meals, lodging, exclusive remedy shall be limited to payment by John
and similar. Deere of actual damages in an amount not to exceed
the cost of the engine.
Service outlet costs incurred in solving or attempting
to solve non-warrantable problems. 8.3.9 No Seller’s Warranty

Services performed by a party other than an No person or entity, other than John Deere, who sells
authorized John Deere engine service dealer, unless the engine or product in which the engine has been
required by law. installed makes any guaranty or warranty of its own
Charges by dealers for initial engine start-up and on any engine warranted by John Deere unless it
inspection, deemed unnecessary by John Deere when delivers to the purchaser a separate written guaranty
operation and maintenance instructions supplied with certificate specifically guaranteeing the engine, in
the engine are followed. which case John Deere shall have no obligation to the
purchaser. Neither original equipment manufacturers,
Costs of interpreting or translating services. engine or equipment distributors, engine or
equipment dealers, nor any other person or entity, has
8.3.7 No Representations or Implied Warranty any authority to make any representation or promise
on behalf of John Deere or to modify the terms or
Where permitted by law, neither John Deere nor any limitations of this warranty in any way.
company affiliated with it makes any guaranties,
warranties, conditions, representations or promises, 8.3.10 Additional Information
express or implied, oral or written, as to the
nonoccurrence of any defect or the quality or For additional information concerning the John Deere
performance of its engines other than those set forth New Off-Highway Engine Warranty, see booklet
herein, and DOES NOT MAKE ANY IMPLIED Engine Owner’s Warranty – Worldwide.
WARRANTY OR CONDITIONS OF
MERCHANTABILITY OR FITNESS otherwise 9.0 ATCM CALIFORNIA EMISSIONS
provided for in the Uniform Commercial Code or REGULATIONS FOR STATIONARY ENGINES
required by any Sale of Goods Act or any other
statute. This exclusion includes fundamental terms. NOTICE AND DISCLAIMER
In no event will a John Deere engine distributor or FOR STATIONARY COMPRESSION
engine service dealer, John Deere equipment dealer, IGNITION ENGINES INSTALLED IN
or John Deere or any company affiliated with John CALIFORNIA AFTER JANUARY 1, 2005
Deere be liable for incidental or consequential
damages or injuries including, but not limited to, loss

Page 38 of 41
1. This Notice and Disclaimer is an addendum SUPPLIED BY CLARKE WILL COMPLY
to, and made a part of, Clarke’s Fire WITH THE ATCM. CLARKE ALSO
Protection Products, Inc.’s (“Clarke”) EXPRESSLY DISCLAIMS THAT THE
Standard Terms and Conditions of Sale and, ENGINES SUPPLIED BY CLARKE WILL,
in all respects not inconsistent therewith, also IN FACT, COMPLY WITH THE ATCM.
applies to all sales of stationary compression IN NO EVENT SHALL CLARKE BE
ignition engines installed in California after LIABLE FOR SPECIAL, INCIDENTAL OR
January 1, 2005. CONSEQUENTIAL DAMAGES ARISING
OUT OF OR IN CONNECTION WITH
2. Stationary diesel-fueled compression ignition
THESE TERMS AND CONDITIONS OR
engines installed in California after January
THE ENGINES SUPPLIED BY CLARKE
1, 2005 are subject to California’s Airborne
OR FOR INDEMNIFICATION OF BUYER
Toxic Control Measure for Stationary
ON ACCOUNT OF ANY CLAIM
Compression Ignition Engines (the
ASSERTED AGAINST BUYER, OR FOR
“ATCM”), Cal. Code Regs. Title 17, Section
ANY OTHER DAMAGE OF ANY KIND,
93115. The California Air Resources Board
WHETHER DIRECT OR INDIRECT, IF
(“CARB”) has reviewed the emissions
THE ENGINES SUPPLIED BY CLARKE
estimation methodology provided by Clarke
DO NOT COMPLY WITH THE ATCM.
Fire Protection Products, Inc. (“Clarke”) and
has concluded that Clarke has used a valid 5. If Buyer resells any of the goods sold under
methodology for estimating the emissions this Agreement, Buyer shall include
from engines supplied by Clarke and that the language in an enforceable agreement with
engines presumptively comply with the its buyer that makes the language in this
ATCM’s emissions standards. Clarke’s Agreement, including Clarke’s disclaimer of
methodology used existing emissions test warranties and remedies in paragraph 5,
data associated with similar engines to binding on its buyer. Buyer shall defend,
estimate the emissions produced by the indemnify and hold Clarke harmless from
emergency fire pump engines supplied by any claims, causes of action, damages, losses
Clarke. or expenses (including reasonable attorney’s
fees) that Clarke incurs by reason of Buyer’s
3. CARB’s determination is not binding on the
failure to comply with this paragraph.
local air districts, which have primary
jurisdiction for implementing and enforcing 6. Each Clarke ATCM Compliant Fire Pump
the ATCM. Actual test data in the field or Driver will be affixed with the following
other information established by the local air ATCM Tier 2 Label:
districts or CARB that show actual emissions
from an engine supplied by Clarke in excess
of the ATCM limitations could indicate a
violation of the ATCM and subject the seller,
owner and operator of the engine to penalties
under California law. Although Clarke
believes that the engines supplied by Clarke
comply with the ATCM based on the
available data and methodology accepted by 7. Each Clarke ATCM Compliant Fire
CARB, for the foregoing reasons, Clarke Pump Driver will be stamped with new
cannot, and does not, guarantee that its fuel injection pump timing alignment
engines will comply with the ATCM marks. Refer to figure #___. Original
emission regulations.
‘factory” timing marks will be “X” out.
4. CLARKE MAKES NO WARRANTIES OR
10.0 INSTALLATION & OPERATION DATA
GUARANTIES, EXPRESS OR IMPLIED,
(See Technical Catalog C13965)
INCLUDING ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A
11.0 WIRING DIAGRAMS
PARTICULAR PURPOSE OR
(See Technical Catalog C13965)
OTHERWISE, THAT THE ENGINES

Page 39 of 41
12.0 PARTS ILLUSTRATION DRAWING
(See Technical Catalog C13965)

13.0 APPENDIX (Alpha Index)

Page 40 of 41
13.0 APPENDIX (Alpha Index)
Subject Page
Subject Page
L
A Lube Oil Recommendations 28
ACTM Compliant Engines 38
Lubricating Oil Volume 28
Air Cleaner 25,33
Lubricating System 27
Alternator 32,33
M
B Magnetic Pickup 33
Battery Cables 13
Maintenance Schedule 33
Battery Recommendations 13,32
Manual Operation 16
Belt Adjustment 32
Model Number Identification 5
C
N
Capacities 29,30
Name Plate (Engine) 5
Coolant Recommendations 29,30
Cooling System
O
Anti-Freeze Solutions 29,30
Oil Filter 27
Cooling System Capacity 29
Oil Level Dipstick 27
Cooling Water Supply (Loop) 12,15
Oil Pressure *
Cooling Water Flow Requirements *
Oil Specifications/Recommendations 28
Filling Procedure 30
Operation Data *
Heat Exchanger 12,15,31
Out Of Fuel Procedures 12
Inhibitors 29,30,33
Overspeed Reset 33
Maintenance 33,34
Overspeed Verification 33
Radiator 11,15,25,33
Water 27
P
Crankcase Ventilation 26
Parts Illustrations *
Parts Information 34
D Preventive Maintenance Schedule 33
Dipstick, Oil Level 27
Pump:
Driveshaft alignment 11
Fuel Injection Pump 20,23,24,37
Driveshaft Maintenance 13,33
Fuel Lift Pump 16
E
S
Electrical System 31,32
Serial Number 5
Engine Models 6
Shutdown Systems 33
Engine Out of Fuel 11
Specifications:
Engine Protective Systems (overspeed) 33
Fuel 12
Engine Start-Up Service 16
Lubrication Oil 28
Exhaust System 24
Speed Switch 33
Storage 11
F
Filters:
Air Cleaner 25,33
T
Fuel 19,34
Technical Data *
Lubricating Oil 9,27,28,34
Fuel Specifications 10,11
W
Fuel System Operation 19
Warranty 35
Bleeding 19
Wiring Diagram:
Pump, Injection 5,20,33,37,39
DC System 32*
Pump, Lift 16
AC Heater Systems 32*
Service 14 to 23

G
Governor Speed Adjustment 33

H
Heaters, Engine 12

I
Installation Data *
Installation Instructions 10
* See Technical Catalog C13965

Page 41 of 41