Internal Use Only

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

LED MONITOR
SERVICE MANUAL
CHASSIS : LK53B

MODEL : 32MB17HM 32MB17HM-BN

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL68920152 (1508-REV00) Printed in Korea

 CONTENTS

CONTENTS ............................................................................................... 2

SAFETY PRECAUTIONS.......................................................................... 3

.
SERVICING PRECAUTIONS.................................................................... 4

SPECIFICATION........................................................................................ 6

ADJUSTMENT INSTRUCTION................................................................. 8

TROUBLE SHOOTING............................................................................ 11

.
BLOCK DIAGRAM.................................................................................. 14

EXPLODED VIEW ................................................................................... 15

Copyright © LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1W), keep the resistor 10mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
AC Volt-meter

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed Good Earth Ground
such as WATER PIPE,
metallic parts of the cabinet, such as antennas, terminals, etc., to CONDUIT etc.
To Instrument's
be sure the set is safe to operate without damage of electrical exposed
0.15µF
shock. METALLIC PARTS

Leakage Current Cold Check(Antenna Cold Check) 1.5 Kohm/10W

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
When 25A is impressed between Earth and 2nd Ground
switch in the on position, connect one lead of ohm-meter to the AC for 1 second, Resistance must be less than 0.1
plug prongs tied together and touch other ohm-meter lead in turn to *Base on Adjustment standard
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright © LG Electronics. Inc. All right reserved. -3- LGE Internal Use Only
Only for training and service purposes
 SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES
SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or
following servicing precautions and any of the safety precautions on exposure of the assembly.
page 3 of this publication, always follow the safety precautions. 3. Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as "anti-static" can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 5. Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or package until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are packaged with leads
c. Connecting a test substitute in parallel with an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A wrong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
explosion hazard. to the chassis or circuit assembly into which the device will be
installed.
2. Test high voltage only by measuring it with an appropriate high CAUTION: Be sure no power is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged
Do not test high voltage by "drawing an arc". replacement ES devices. (Otherwise harmless motion such as
3. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified otherwise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10% (by volume) Acetone and 90% (by 1. Use a grounded-tip, low-wattage soldering iron and appropriate
volume) isopropyl alcohol (90%-99% strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 ˚F to 600 ˚F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 ˚F to 600 ˚F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 ˚F to 600 ˚F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor "chip" components. The following techniques only until the solder flows onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. splashed solder with a small wire-bristle brush.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the

Copyright © LG Electronics. Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement CAUTION: Maintain original spacing between the replaced
Some chassis circuit boards have slotted holes (oblong) through component and adjacent components and the circuit board to
which the IC leads are inserted and then bent flat against the prevent excessive component temperatures.
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with Circuit Board Foil Repair
boards using the familiar round hole, use the standard technique Excessive heat applied to the copper foil of any printed circuit
as outlined in paragraphs 5 and 6 above. board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
Removal following guidelines and procedures should be followed whenever
1. Desolder and straighten each IC lead in one operation by gently this condition is encountered.
prying up on the lead with the soldering iron tip as the solder
melts. At IC Connections
2. Draw away the melted solder with an anti-static suction-type To repair a defective copper pattern at IC connections use the
solder removal device (or with solder braid) before removing the following procedure to install a jumper wire on the copper pattern
IC. side of the circuit board. (Use this technique only on IC
Replacement connections).
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and 1. Carefully remove the damaged copper pattern with a sharp
solder it. knife. (Remove only as much copper as absolutely necessary).
3. Clean the soldered areas with a small wire-bristle brush. 2. carefully scratch away the solder resist and acrylic coating (if
(It is not necessary to reapply acrylic coating to the areas). used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
"Small-Signal" Discrete Transistor carefully crimp it around the IC pin. Solder the IC connection.
Removal/Replacement 4. Route the jumper wire along the path of the out-away copper
1. Remove the defective transistor by clipping its leads as close as pattern and let it overlap the previously scraped end of the good
possible to the component body. copper pattern. Solder the overlapped area and clip off any
2. Bend into a "U" shape the end of each of three leads remaining excess jumper wire.
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads. At Other Connections
4. Connect the replacement transistor leads to the corresponding Use the following technique to repair the defective copper pattern
leads extending from the circuit board and crimp the "U" with at connections other than IC Pins. This technique involves the
long nose pliers to insure metal to metal contact then solder installation of a jumper wire on the component side of the circuit
each connection. board.

Power Output, Transistor Device 1. Remove the defective copper pattern with a sharp knife.
Removal/Replacement Remove at least 1/4 inch of copper, to ensure that a hazardous
1. Heat and remove all solder from around the transistor leads. condition will not exist if the jumper wire opens.
2. Remove the heat sink mounting screw (if so equipped). 2. Trace along the copper pattern from both sides of the pattern
3. Carefully remove the transistor from the heat sink of the circuit break and locate the nearest component that is directly
board. connected to the affected copper pattern.
4. Insert new transistor in the circuit board. 3. Connect insulated 20-gauge jumper wire from the lead of the
5. Solder each transistor lead, and clip off excess lead. nearest component on one side of the pattern break to the lead
6. Replace heat sink. of the nearest component on the other side.
Carefully crimp and solder the connections.
Diode Removal/Replacement CAUTION: Be sure the insulated jumper wire is dressed so the
1. Remove defective diode by clipping its leads as close as it does not touch components or sharp edges.
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.

Copyright © LG Electronics. Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes
 SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application Range
This spec sheet is applied all of the TV used LK53B chassis.

2. Specification
Each part is tested as below without special appointment

1) Temperature : 25 ˚C ± 5 ˚C (77 ˚F ± 9 ˚F),

CST : 40 ˚C ± 5 ˚C
2) Relative Humidity : 65 % ± 10 %
3) Power Voltage : Standard input voltage
(100 V - 240 ­V ~, 50 / 60 Hz)
·S  tandard Voltage of each products is marked by models
4) Specification and performance of each parts are followed
each drawing and specification by part number in accord-
ance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.

3.Test method
1) Performance : LGE TV test method followed
2) Demanded other specification
- Safety : CE,IEC specification
- EMC : CE,IEC specification

4. General specification
No Item Specification Remarks

1 Display Screen Device 31.51” WXGA wide Color Display Module Resolution 1920x1080

2 Aspect Ratio 16:9

3 LCD Module HC320DXN-SLNS2

HC320DXN-SLNS4
4 Storage Environment Temp. : -20 ~ 60 deg
Humidity : 10 ~ 90 %
5. Operating Environment Temp. : 0 ~ 40 deg
Humidity : 0 ~ 85 %
6 Input Voltage 100~240V@ 50/60Hz

7 Module Power Con- 17.77W(Typ.) Full White Pattern

sumption

Copyright © LG Electronics. Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes
5. External Input Support Format
5.1. HDMI (PC)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark
1 720*400 31.468 70.08 28.321
2 640*480 31.469 59.94 25.175
3 640*480 37.500 75.00 31.500
4 800*600 37.879 60.317 40.000
5 800*600 46.875 75.00 49.500
6 1024*768 48.363 60.004 65.000
7 1024*768 60.023 75.029 78.750
8 1280*800 49.702 59.81 83.500
9 1366*768 47.717 59.79 85.5

5.2. HDMI (DTV)

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark
1 720* 480 31.469 / 31.5 59.94 / 60 27.00/ 27.03 SDTV 480P
2. 720*576 31.25 50.00 27.864 SDTV 576P
3. 1280*720 37.50 50.00 74.250 HDTV 720P
4 1280* 720 44.96 / 45 59.94 / 60 74.17/ 74.25 HDTV 720P
5 1920* 1080 33.72 / 33.75 59.94 / 60 74.17/ 74.25 HDTV 1080I
6 1920* 1080 28.125 50.00 74.25 HDTV 1080I
7 1920* 1080 27.00 24 74.25 HDTV 1080P
8 1920* 1080 33.75 30.00 74.25 HDTV 1080P
9 1920* 1080 56.250 50 148.5 HDTV 1080P
10 1920* 1080 67.43 / 67.5 59.94 / 60 148.35/ 148.50 HDTV 1080P

5.3. Component
Specification
No Remark
Resolution H-freq(kHz) V-freq(Hz) Pixel clock( MHz)
1 720* 480 15.73 59.94 13.500 SDTV, DVD 480I( 525I)
2 720* 480 15.75 60.00 13.514 SDTV, DVD 480I( 525I)
3 720* 576 15.625 50.00 13.500 SDTV, DVD 576I( 625I) 50Hz
4 720* 480 31.47 59.94 27.000 SDTV 480P
5 720* 480 31.50 60.00 27.027 SDTV 480P
6 720* 576 31.25 50.00 27.000 SDTV 576P 50Hz
7 1280* 720 44.96 59.94 74.176 HDTV 720P
8 1280* 720 45.00 60.00 74.250 HDTV 720P
9 1280* 720 37.50 50.00 74.25 HDTV 720P 50Hz
10 1920* 1080 33.72 59.94 74.176 HDTV 1080I
11 1920* 1080 33.75 60.00 74.250 HDTV 1080I
12 1920* 1080 28.125 50.00 74.250 HDTV 1080I 50Hz
13 1920* 1080 56.25 50 148.5 HDTV 1080P
14 1920* 1080 67.432 59.94 148.350 HDTV 1080P
15 1920* 1080 67.5 60.00 148.5 HDTV 1080P

Copyright © LG Electronics. Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes
 ADJUSTMENT INSTRUCTION
1. Application Range 4) Click “Read” tab, and then load download file(XXXX.bin) by
clicking “Read”
This document is applied to LK53B chassis Set which is
manufactured in TV (or Monitor) Factory or is produced on the (4)
basis of this data.
filexxx.bin

2. Designation
1) The adjustment is according to the order which is designat-
ed and which must be followed, according to the plan which
can be changed only on agreeing.
2) Power adjustment : Free Voltage.
3) Magnetic Field Condition: Nil. 5) Click “Auto” tab and set as below
4) Input signal Unit: Product Specification Standard. 6) Click “Run”.
5) Reserve after operation: Above 5 Minutes (Heat Run) 7) After downloading, check “OK” message.
Temperature : at 25 °C ± 5 °C
Relative humidity : 65 % ± 10 % (5)
Input voltage : 220 V, 60 Hz
6) Adjustment equipments : Color Analyzer (CA-210 or CA- (5)
110), DDC Adjustment Jig equipment, SVC remote controll.
7) Push The "IN STOP KEY" – For memory initialization (7) ……….OK

Case1 : Software version up (6)

1) After downloading S/W by USB , Multi-vision set will
reboot automatically
2) Push "In-stop" key
3) Push "Power on" key
4) Function inspection * USB DOWNLOAD(*.epk file download)
5) After function inspection, Push "In-stop" key. 1) Make New folder named “LG_DTV” and put ISP file(*.epk)
in the folder.
Case2 : Function check at the assembly line 2) Put the USB Stick to the USB socket.
1) When TV set is entering on the assembly line, Push "In- 3) Automatically detecting update file in USB Stick
stop" key at first. - If your downloaded program version in USB Stick is
2) Push "Power on" key for turning it on. Low, it didn’t work. But your downloaded version is
→ If you push "Power on" key, TV set will recover channel High, USB data is automatically detecting.
information by itself. 4) Show the message “Copy the file from the Memory…”
3) After function inspection, Push "In-stop" key.

3. Main PCB check process

* APC - After Manual-Insult, executing APC

5) Updating is starting.
* Boot file Download
1) Execute ISP program “Mstar ISP Utility” and then click
“Config” tab.
2) Set as below, and then click “Auto Detect” and check “OK”
message. If display “Error”, Check connect computer, jig,
and set.
3) Click “Connect” tab. If display “Can’t ”, Check connect
computer, jig, and set. 6) Updating Completed, The TV will restart automatically.
7) If your TV is turned on, check your updated version and
(1) (3) Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV
Please Check the Speed :
have, TV can lost all channel data. In this case, you
Use the speed under have to channel recover. if all channel data is cleared,
200KHz. you didn’t have a DTV/ATV test on production line.
(2) OK

Copyright © LG Electronics. Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes
3.1. EDID Process 4. Total Assembly line process
3.1.1. EDID download
1) Press “Power only” key of service remote controll.
2) Press the “ADJ” Key of service remote controll.
3) Enter EDID D/L mode by pushing “►” key at “EDID D/L”.
4) Select “Start” menu to download EDID data.
5) Check the “OK” message.
6) Press EXIT key on R/C.
GG
WUG{––“Gv—›–•XG
WUG{––“Gv—›–•XG GG GG
XUG{––“Gv—›–•YG
XUG{––“Gv—›–•YG GG GG
YUG{––“Gv—›–•ZG
YUG{––“Gv—›–•ZG GG GG
ZUG{––“Gv—›–•[G
ZUG{––“Gv—›–•[G GG GG
[UG{––“Gv—›–•\G
[UG{––“Gv—›–•\G GG GG
\UG{––“Gv—›–•]G
\UG{––“Gv—›–•]G GG GG
]UGj–œ•›™ Gn™–œ—G
]UGj–œ•›™ Gn™–œ—G
^UGh™ŒˆGv—›–•G
^UGh™ŒˆGv—›–•G GG GG
_UGhkjGjˆ“‰™ˆ›–•G
_UGhkjGjˆ“‰™ˆ›–•G
`UG~›ŒGiˆ“ˆ•ŠŒG
`UG~›ŒGiˆ“ˆ•ŠŒG GG GG
XWUGXWGw–•›G~iG
XWUGXWGw–•›G~iGGG GG GG
XXUG{Œš›Gwˆ››Œ™•G
XXUG{Œš›Gwˆ››Œ™•GGGGG GG GG
XYUGlkpkGkVsG
XYUGlkpkGkVsG ඖG
ඖG GG lkpkGkVsG
lkpkGkVsG
XZUGzœ‰GiVjG
XZUGzœ‰GiVjG GG GG oktpXG
oktpXGGGGGGGGGGGGGGGGGGGGGGGvrG
vrG GG GG
X[UG{–œŠGzŒ•š›› GzŒ››•ŽG
X[UG{–œŠGzŒ•š›› GzŒ››•ŽG yniG
yniGGGGGGGGGGGGGGGGGGGGGGGGGGGvrG
vrG GG GG
X\UGlŸ›UGp•—œ›Gh‹‘œš›G
X\UGlŸ›UGp•—œ›Gh‹‘œš›G GG GG GG
X]UGzwrGs—š •ŠGh‹‘œš›G
X]UGzwrGs—š •ŠGh‹‘œš›G GG
X^UzwkpmGs—š •ŠGh‹‘œš›G
X^UzwkpmGs—š •ŠGh‹‘œš›G GG z›ˆ™›G
z›ˆ™›G GG yŒšŒ›G
yŒšŒ›G GG
GG GG GG GG

→ Caution: - Do not connect HDMI & D-sub Cable when

4.1. Tool option & ADC Check
1) Press “Power on” key of service remote control.
download EDID.
2) Connect RS232 Signal Cable to RS-232 Jack.
3) Check the 'Tool Option' (Refer to the BOM Comments or
* Edid data and Model option download (RS232)
Adjustment spec)
NO Item CMD CMD Data 0
1 2 4) Check the ‘ADC’ is ok.
Enter Download A A 0 0 When transfer the
download
MODE
‘Mode In’ ‘Mode In’,
Carry the command.
4.2. M
 odel name & Serial number Down-
EDID data and Download A E 00 10 Automatically download load
Model option (The use of a internal 4.2.1. Model name & Serial number D/L
download Data)
1) Press "Power on" key of service remote control.
2) Connect USB Port → USB to Serial Adapter (UC-232A) →
→ Caution
RS-232C cable → PC(RS-232C port)
* Use the proper signal cable for EDID Download
3) Write Model Name & Serial Number by use USB Port
- Analog EDID : Pin3 exists
4) Must check the serial number at the Diagnostics of SET UP
- Digital EDID : Pin3 exists
menu. (Refer to below).
3.1.2. EDID data
- RGB : Check sum : BC
- HDMI1 : Checksum : 13 7E
- HDMI2 : Checksum : 13 6E

3.2. Function Check

3.2.1. Check display and sound
*Check Input and Signal items. (cf. work instructions) 4.2.2. Method & notice
1) AV (CVBS) 1) Model Name & Serial Number D/L is using of scan equip-
2) COMPONENT (480i) ment.
3) HDMI(PC : 1366x768 @ 60Hz) 2) Setting of scan equipment operated by Manufacturing
Technology Group.
* Display and Sound check is executed by Remote controll 3) Serial number D/L must be conformed when it is produced
* Some models do not support RGB & PC audio in. It depends in production line, because serial number D/L is mandatory
on model spec. by D-book 4.0
→ Caution : Not to push the INSTOP KEY after completion if
the function inspection. * Manual Download (Model Name and Serial Num-
ber)
If the TV set is downloaded By OTA or Service man, Some-
times model name or serial number is initialized.( Not always)
There is impossible to download by bar code scan, so It need
Manual download.

Copyright © LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
 1) Press the 'Instart' key of ADJ remote controll. *Note : Manual W/B process using service Remote control.
2) Go to the menu 'Model Number D/L' like below photo. 1) After enter Service Mode by pushing "ADJ" key,
3) Input the Factory model name (ex 24LN4500) or Serial 2) Enter "White Balance" by pushing "►" key at "White Bal-
number like photo. ance".
7. Area Option
8. ADC Calibration
9. W hite Balance ▶
10. 10 Point WB

* When doing Adjustment, Please make circumstance as

below.

4) Check the model name Instart menu → Factory name

displayed (ex 24MT55D)
5) Check the Diagnostics (DTV country only) → Buyer model
displayed (ex 24MT45D-PZP)

4.3. Function Check

4.3.1. Check display and sound
*Check Input and Signal items. (cf. work instructions) 4.5. DPM Operation check
1) AV (CVBS) ■ Measurement Condition: 100~240V@ 50/60Hz
2) COMPONENT (480i) 1) Set Input to RGB-PC and connect D-sub cable to set –
3) HDMI(PC : 1366x768 @ 60Hz) RGB Mode
S
 et Input to HDMI (with Input Label set to PC) and connect
* Display and Sound check is executed by Remote controll HDMI cable to set – HDMI Mode
* Some models do not support RGB & PC audio in. It depends 2) Cut off H sync or V sync of signal.
on model spec. 3) Check DPM operation refer to the below table.
→ Caution : N
 ot to push the INSTOP KEY after completion if the Operating Condition Sync Video LED Wattage
function inspection. (H/V) (SET) (W)
Power S/W On Sleep mode - Off/Off Off Amber 1
RGB,HDMI
4.4. White balance adjustment
-Equipment 4.6. Model Name & SW Version & Adjust check.
1) Color Analyzer: CA-210 (LED Module : CH 14) * Press the ‘Instart’ key of ADJ remote controll
2) Adj. Computer(During auto adj., RS-232C protocol is
needed) 4.6.1. Model Name& SW Version Check
3) Service Remote Controll 1) Check ‘Model Name’.
*RGB Gains are fixed data for each model. 2) Check ‘S/W Version’ (Refer to the IC Ver. in the BOM)
Insert RS-232C Jack which is connected with PC for White
Balance or equivalent device.
4.6.2. Adjust Check
→ Total Assembly line should be check whether the color
1) Check ‘Country Group’
coordinate(x,y) data refer to below table were meet or not.
2) Check ‘Area Option’
- Cool Panel
3) Check ‘Tool Option’ (Refer to the BOM Comments)
Color Cool 13,000 °K X=0.276 (±0.04) <Test Signal>
Temperature Y=0.275 (±0.04) Inner pattern
4) Check ‘Adjust ADC[Comp&RGB]’ is OK.
(204gray,80IRE) 5) Check ‘EDID[RGB&HDMI]’ is OK.
Medium 9,300k °K X=0.292 (±0.04)
Y=0.295 (±0.04)
* After check all, Press the 'EXIT' key of ADJ remote controll
to go out SVC menu.
Warm 6,500k °K X=0.318 (±0.04)
Y=0.334 (±0.04)
Luminance Cool Min : 70 Typ : 110 <Test Signal>
(cd/m²) Inner pattern
Medium Min : 60 Typ : 100 (204gray,80IRE)
Warm Min : 40 Typ : 80

*Note : x ,y coordinates are drifted about 0.007 after 30 mins

heat-run. So checking color coordinate within 5-min at
total assembly line, consider x,y coordinates might be
up to 0.007 than x,y target of each color temperature.

Copyright © LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
 TROUBLE SHOOTING
1. No Power
N Check Power connector Y
Check C400 Replace Adapter
Voltage Level (19V) OK ?

N Replace IC401 &

Check IC401 Output
Voltage Level (3.3V) Recheck

Check IC402 Output N Replace IC402 &

Voltage Level (1.15V) Recheck

N Replace IC403 &

Check IC403 Output
Voltage Level (5V) Recheck

Check X101 Clock N

Replace X101
24MHz

Replace IC100 Flash

Memory

Copyright © LG Electronics. Inc. All right reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
2. No Screen on
N N
Check IC101
Module Back Light On? Check WLED_ENABLE High? Replace Main SOC

Y
Y

N
Check LED Driver NDRV Check IC1000 & Q1000
(R1025) Replace LED Driver IC or FET

N
Check Panel Power 12V (P601 #51) Replace IC400 &
Check IC400 Output 12V Recheck

Check Panel input Clock N Check IC101

P601 (#21, #22 ) Repair Main B/D

Check FFC Cable for Damage or N

Replace Cable
Open Conductors

Replace T-Con Board or Module

Copyright © LG Electronics. Inc. All right reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
3. No Video - HDMI
Check input signal format
Is it supported?

Check HDMI Cable for Damage or

Open Connector

N
Check JK800/801 for proper
Replace Connector
connection or Damage

Check I2C Signal N Re Download EDID Data

(JK800/801)

Replace Main Scaler

(IC101)

Copyright © LG Electronics. Inc. All right reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
 BLOCK DIAGRAM

Copyright © LG Electronics. Inc. All right reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
 EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

900
400

901
535
LV1

801
A2

500
540
A10

120
200

Copyright © LG Electronics. Inc. All right reserved. - 15 - LGE Internal Use Only
Only for training and service purposes