SKF Bearing Select v1.

2-35

February 09, 2020

 1. Abstract

Tapered roller bearing Tapered roller bearing

Static
Frictional
Designation Life model Grease safety Power loss
moment
factor

Relubrication
SKF Explorer Basic SKF life Total
interval

Popular item L10h L10mh tf S0 M Ploss

h Nmm W

Left 33109 191000 > 2x10^5 13800 27.7 637 73

Right 33109 > 2x10^5 > 2x10^5 13800 45.9 251 29

* SKF rating life ( L10mh ) for steel-steel bearings; GBLM load based life ( L10GMh ) for hybrid bearings

Left bearing

! For rating life results above 100000 hours, other failure modes than those included in the current rating life models will dominate and limit the
life of the bearing.

Right bearing

! For rating life results above 100000 hours, other failure modes than those included in the current rating life models will dominate and limit the
life of the bearing.

SKF Bearing Select 2 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 2. Input
2.1. Bearing data

Designation Bearing type Principal dimensions Basic load ratings Fatigue load limit

SKF Explorer Dynamic Static

Popular item d D B C C0 Pu

mm kN

Tapered roller
Left 33109 45 80 26 104 114 12.9
bearing

Tapered roller
Right 33109 45 80 26 104 114 12.9
bearing

Designation Speed ratings

Reference Limiting

nref nlim

r/min

Left 33109 6700 8000

Right 33109 6700 8000

SKF Bearing Select 3 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 2.2. Loads & Speed

Bearing distance 26.0 mm

Shaft orientation Horizontal

Rotating ring Inner ring rotation

Coordinate Case
Load Coordinates Forces Speed
system weight

x|r y|θ Z Fx|Fr Fy|Fθ Fz

mm mm|deg mm kN kN kN r/min

LC1 F1 Cartesian 0.0 0.0 13.0 1.368 -4.777 2.424 1100.0 1.0

2.3. Temperature

Load Cases Left Right

Inner ring Outer ring Inner ring Outer ring

°C

LC1 70 65 70 65

- Maximum temperature is used for calculating the actual viscosity, kappa, aSKF and SKF rating life.

- Mean temperature is used for calculating bearing friction and power loss.

SKF Bearing Select 4 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 2.4. Lubrication

Effective EP
Designation Lubricant Viscosity
additives

SKF Explorer Type Method Name @40°C @100°C

Popular item mm²/s

LGBB 2: wind
turbine blade and
Left 33109 Grease SKF grease False 68 10
yaw bearing
grease

LGBB 2: wind
turbine blade and
Right 33109 Grease SKF grease False 68 10
yaw bearing
grease

Designation Contamination

Method Cleanliness / Factor

Left 33109 Detailed guidelines High cleanliness

Right 33109 Detailed guidelines High cleanliness

2.5. Fits and tolerances

Calculated Include
Designation Requirements Tolerance Class
interference Smoothing

SKF Explorer Guidance Housing Shaft

Popular item

Left 33109 False J6 j5 True True

Right 33109 False J6 j5 True True

SKF Bearing Select 5 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3. Results

3.1. Loads & static safety

Static safety Equivalent dynamic

Designation Load ratio Equivalent static load
factor load

SKF Explorer

Popular item C/P S0 P P0

kN

Left 33109 17.01 27.7 6.11 4.12

Right 33109 41.86 45.9 2.48 2.48

3.2. Bearing minimum load

Designation Reaction forces Minimum load

SKF Explorer Radial Axial met?

Popular item Fr Fa Fr m Fa m

kN

Left 33109 2.48 -3.2 1.76 0.62 yes

Right 33109 2.48 0.776 1.76 0.62 yes

SKF Bearing Select 6 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.3. Adjusted reference speed

Adjusted reference
Designation Adjustment factors
speed

SKF Explorer For bearing load P For oil viscosity

Popular item nar fp fv

r/min

Left 33109 7290 0.99 1.11

Right 33109 7410 1.0 1.11

3.4. Lubrication conditions

Viscosity
Designation Operating viscosity
ratio

Rated @ 40
SKF Explorer Actual Rated
°C

Popular item ν ν1 νref K

mm²/s

Left 33109 22.1 14.1 43.8 1.56

Right 33109 22.1 14.1 43.8 1.56

SKF Bearing Select 7 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.5. Grease life and relubrication interval

Relubrication Initial Grease

Designation Speed factor
interval fill quantity

SKF Explorer Side Side Speed x mean diameter

Popular item tf V Gp ndm

h cm³ g mm/min

Left 33109 13800 8 10 68700

Right 33109 13800 8 10 68700

3.6. Bearing rating life

SKF life modification

Designation Bearing rating life Contamination factor
factor

SKF Explorer Basic SKF

Popular item L10h L10mh askf ηc

Left 33109 191000 > 2x10^5 50.0 0.83

Right 33109 > 2x10^5 > 2x10^5 50.0 0.83

* SKF rating life ( L10mh ) for steel-steel bearings; GBLM load based life ( L10GMh ) for hybrid bearings

Left bearing

! For rating life results above 100000 hours, other failure modes than those included in the current rating life models will dominate and limit the
life of the bearing.

Right bearing

! For rating life results above 100000 hours, other failure modes than those included in the current rating life models will dominate and limit the
life of the bearing.

SKF Bearing Select 8 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.7. Bearing friction & power loss

Power
Designation Frictional moment Friction Sources
loss

At start
20-30°C
SKF Explorer Total Rolling Sliding Seals Drag loss
and zero
speed

Popular item M Mstart Mrr Msl Mseal Mdrag Ploss

Nmm W

Left 33109 637 684 584 52.7 0 0 73

Right 33109 251 165 238 12.7 0 0 29

SKF Bearing Select 9 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.8. Bearing frequencies

Designation Rotational frequencies

Rolling element set & Rolling element about its

SKF Explorer Inner ring Outer ring
cage axis

Popular item fi fe fc fr

Hz

Left 33109 18.3 0 7.94 65.6

Right 33109 18.3 0 7.94 65.6

Designation Frequency of over-rolling

Point on inner ring Point on outer ring Rolling element

fip fep frp

Hz

Left 33109 218 166 131

Right 33109 218 166 131

SKF Bearing Select 10 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.9. Fits and tolerances
3.9.1. Tolerances

Designation Shaft outer diameter Bearing bore Bearing outer diameter

SKF
Minimum Maximum Minimum Maximum Minimum Maximum
Explorer

Popular
µm
item

Left 33109 -5 6 -12 0 -16 0

Right 33109 -5 6 -12 0 -16 0

Designatio
Housing bore Smoothing
n
SKF Maximu Shaft and
Minimum Bearing outer ring and housing
Explorer m bearing bore

Popular
µm
item

Left 33109 -6 13 4 12

Right 33109 -6 13 4 12

- inputtolerancesMessage

SKF Bearing Select 11 2020-02-09

This report was produced with SKF Bearing Select software. Please note the limited warranty, shown at the bottom of the last page of this report
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.
 3.9.2. Fits, Probable Interference (-) / Clearance (+)

Designation Shaft Housing

Probable Probable Probable Probable

SKF Explorer Middle Middle
minimum maximum minimum maximum

Popular item µm

Left 33109 -6 3 11 -36 -24 -11

Right 33109 -6 3 11 -36 -24 -11

SKF Bearing Select 12 2020-02-09

LIMITED WARRANTY : The SKF Bearing Select software tool of the SKF Company supports the calculation and selection of bearings.
This software is provided 'as is' with out any warranty of any sort, implicitly as well as explicitly.
Please note that the obtained results can be affected by many external parameters and/or the quality of the assumptions taken into account.
The results obtained using this software must be validated by the user who accepts the fact that the use of this software and the exploitation
of the obtained results are under the user's entire and sole responsibility.
® SKF is a registered trademark of the SKF Group. © SKF Group 2019.