CHAPTER 7 – CONTROL AND FIELD INSTRUMENTATION DOCUMENTATION 113

Question: Does the vessel have an agitator?

Answer: Yes, the figure shows an agitator impeller in the
vessel, powered by a motor on top of the vessel.

Question: Is the pump fixed speed or variable speed?

Answer: Since control of the process is done using a regu-
lating valve, then it may be assumed that the pump is fixed
speed.

Question: How could the liquid in the vessel be heated?

Answer: A heat exchanger is shown in the recirculation line
and could be used to heat (or cool) the liquid in the vessel.

Question: How is the pH of the incoming stream adjusted?

Answer: The output of AC103 and AC104 go to a valve and
flow loop, respectively, that regulates the flow of reagent to
the inlet stream and recirculation line. Thus, it may be
assumed that reagent is used to adjust pH.

7.8.2 Example – Basic Column Control

The basic column control system shown in Figure 7-17 is somewhat more
complicated than the basic neutralizer control system. However, after
studying this example, it will become clear that many of the components
that make up the column control system are similar to those used in the
basic neutralizer control system. As we have seen, what is learned by
working with one process may be often applied to another process. Once
you become familiar with a few processes, it becomes easier to work with
other processes.

7.8.3 Example – Batch Reactor Control System

Batch processing plays an important role in some industries. In a batch
process, a vessel is charged with feed material that is processed in the ves-
sel through mechanical or chemical means (or both). At the end of the pro-
cess, the product—which may be a finished product or an intermediate
product for use in another process—is removed from the vessel. The batch
reactor example illustrated in Figure 7-18 is known as “continuous feed
batch,” in which feed material is continuously added to the vessel
throughout part or all of the batch processing. The reaction takes place,
and finally the product is pumped from the vessel. In comparing the basic
components to those seen in the previous two examples, the only new ele-
ment introduced by this example is an eductor (a device that produces
vacuum by means of the Venturi effect) that is used to remove gases cre-
ated by the batch reaction.
114 CONTROL LOOP FOUNDATION: BATCH AND CONTINUOUS PROCESSES

PV
PC 115
115
FO Vent
Feedforward LC
FT111 LT
Feed Tank 117 117

Distillate FC
FC 118
Receiver
114
FV FV
PT 114 118
115 FT FT
Reflux FO 114 118
FC
FC Overheads
111
FV FT111 Feedforward
111
FT
RTD
Column TT
111 Feed TC
FC
116 116
Storage Tank

FC LC
110 113
FV
110 FC
FT 112
LT
110 113 FV
FC Steam 112
FT
Bottoms 112
FC

Figure 7-17. Basic Column Control System

PC
128
TC FO
126 PV PT
127 PV
128
FC TT 128
122 126 Vent System
FO
Eductor

FV TV
122 126
FT
122 PC
FC FO
Anti-Foam Coolant 127 TC
124
FC
PT
121 TT
FV 127
125
121
FT TC
121 FC 125
Feed B

FC TT TV
120 124 125
FV
120 Coolant
FO
FT
120 FC Feed A LT
Batch Reactor LC
123 123
LV
123

Discharge FC
Figure 7-18
Figure 7-18. Example – Batch Reactor Control
 CHAPTER 7 – CONTROL AND FIELD INSTRUMENTATION DOCUMENTATION 115

7.8.4 Example – Continuous Feed and Recycle Tank

In studying the example of a continuous feed and recycle tank shown in
Figure 7-19, you will note that the only new function that was not con-
tained in a previous example is FFC133. The function letters of the tag
number indicate that this new function is ratio control. The line connec-
tions indicate that the ratio control is implemented using two feed streams
to Reactor 1.

FC
135
FV
135
FT Recycle
135
FC
Makeup Recycle Tank

FC
LC LT 133
134 134 FV
133
FT
133 FC Reactor 1

FC
132
FFC FV
133 132
PC FT
130 132
Feed Tank FC Reactor 1
FO
FC
PV 131
130 PT FV
130 131
FT
131
FC Reactor 2

Figure 7-19. Example – Continuous Feed and Recycle Tank

Knowing the tag number and symbols on a P&ID is the first step in under-
standing which measurement and control functions have been installed on
the process. As the examples shown in Figure 7-16 to 7-19 illustrate, a
basic understanding of the control and process is possible if you are famil-
iar with the tag number and symbols on the P&ID. Later chapters on con-
trol implementation will address how the control functions shown on the
P&ID and loops sheet are implemented.
116 CONTROL LOOP FOUNDATION: BATCH AND CONTINUOUS PROCESSES

References
1. The International Society of Automation (ISA). http://
www.isa.org.
2. International Electrotechnical Commission (IEC). http://
www.iec.ch.
3. OSHA Standard 29 CFR 1910.119, Process safety management of
highly hazardous chemicals. http://www.osha.gov.
4. ISA-5.4-1991, Instrument Loop Diagrams, Research Triangle Park,
NC: ISA (ISBN 1-55617-227-3).
5. Skousen, Philip. Valve Handbook – Second Edition, Chapter 1.5.1,
McGraw-Hill Handbook (ISBN: 0071437738).
6. Lehtinen, Marjaana. More speed and accuracy for basis weight
control, pp. 22–24, Automation 1, 2004.