BS 

EN ISO 9606‑1:2017

BSI Standards Publication

Qualification testing of welders — Fusion welding

Part 1: Steels
BS EN ISO 9606‑1:2017 BRITISH STANDARD

National foreword
This British Standard is the UK implementation of EN ISO 9606-1:2017.
It is identical to ISO 9606-1:2012, incorporating corrigendum September
2012. It supersedes BS EN ISO 9606-1:2013, which is withdrawn.
Please note that ISO corrigendum 2:2013 only affects the French edition
and has therefore not been incorporated in this version.
During the development of this standard a new option (option c) was
introduced to clause 9.3 to revalidate a welder’s qualification. It is the
opinion of the UK committee that options a) and b) are the preferred
methods for the periodic verification of a welder’s ability/skill to
reproduce and meet the acceptance levels of the original test conditions.
Attention is drawn to clause 9.3 and which option/s may or may not
be relevant or allowed in application standards or specific contract
requirements. For the relationship with EU directives 2014/68/EU (PED)
and 2014/29/EU (SPVD), see informative Annex ZA and ZB, respectively.
The UK participation in its preparation was entrusted to Technical
Committee WEE/36, Qualification of welding personnel and
welding procedures.
A list of organizations represented on this committee can be obtained on
request to its secretary.
This publication does not purport to include all the necessary provisions
of a contract. Users are responsible for its correct application.
© The British Standards Institution 2017
Published by BSI Standards Limited 2017
ISBN 978 0 580 94361 4
ICS 25.160.10; 03.100.30
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 30 September 2017.

Amendments/corrigenda issued since publication

Date Text affected
 BS EN ISO 9606‑1:2017

EUROPEAN STANDARD EN ISO 9606-1

NORME EUROPÉENNE
EUROPÄISCHE NORM August 2017

ICS 25.160.01 Supersedes EN ISO 9606-1:2013

English Version

Qualification testing of welders - Fusion welding - Part 1:

Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor
2:2013)
Épreuve de qualification des soudeurs - Soudage par Prüfung von Schweißern - Schmelzschweißen - Teil 1:
fusion - Partie 1 : Aciers (ISO 9606-1:2012, y compris Stähle (ISO 9606-1:2012, einschließlich Cor 1:2012
Cor 1:2012 et Cor 2:2013) und Cor 2:2013)

This European Standard was approved by CEN on 16 July 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION

COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9606-1:2017 E
worldwide for CEN national Members.
BS EN ISO 9606‑1:2017
EN ISO 9606-1:2017 (E)

European foreword

The text of ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013 has been prepared by Technical
Committee ISO/TC 44 “Welding and allied processes” of the International Organization for
Standardization (ISO) and has been taken over as EN ISO 9606-1:2017 by Technical Committee
CEN/TC 121 “Welding and allied processes” the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2018, and conflicting national standards
shall be withdrawn at the latest by February 2018.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 9606-1:2013.

This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directives 2014/68/EU
and 2014/29/EU.

For relationship with EU Directives, see informative Annex ZA and ZB, which is an integral part of this
document.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

Endorsement notice

The text of ISO 9606-1:2012 including Cor.1:2012 and Cor 2:2013 has been approved by CEN as EN
ISO 9606-1:2017 without any modification.

3
 BS EN ISO 9606‑1:2017
EN ISO 9606-1:2017 (E)

Annex ZA
(informative)

Relationship between this European Standard and the essential

requirements of EU Directive 2014/68/EU [2014 OJ L 189] (PED) aimed to
be covered

This European Standard has been prepared under a Commission's standardization request M/071
"Mandate to CEN for standardization in the field of pressure equipment" to provide one voluntary
means of conforming to essential requirements of Directive 2014/68/EU (PED) on the harmonisation of
the laws of the Member States relating to the making available on the market of pressure equipment
[2014 OJ L 189].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2014/68/EU
(PED) [2014 OJ L 189]

Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes

Directive 2014/68/EU of this EN
(PED)
Clauses 5, 6.2 to 6.6, 7, 8, 10, 11 Qualification testing
For pressure equipment in
categories II, III and IV the
examiner/examining body
Clauses 6.1, 9.1, 9.3 a), 9.3 b) (according to 3.3 and 3.4) is a
Annex I, 3.1.2
competent third party – a notified
body or a recognized third party
organization.
Not permitted for categories II, III
Clause 9.3 c)
and IV products.

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) and services falling within
the scope of this standard.

4
BS EN ISO 9606‑1:2017
EN ISO 9606-1:2017 (E)

Annex ZB
(informative)

Relationship between this European Standard and the Essential

Requirements of EU Directive 2014/29/EU (SPVD) [2014 OJ L96]

This European Standard has been prepared under a Commission's standardization request M/071
"Mandate to CEN for standardization in the field of pressure equipment" to provide one voluntary
means of conforming to essential requirements of Directive 2014/29/EU (SPVD) on the harmonisation
of the laws of the Member States relating to the making available on the market of simple pressure
vessels [2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZB.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZB.1 — Correspondence between this European Standard and Directive 2014/29/EU
(SPVD) [2014 OJ L96]

Essential Requirements of Clause(s)/sub-clause(s) Remarks/Notes

Directive 2014/29/EU of this EN
(SPVD)
For welds on pressurised parts of
simple pressure vessels the
Clauses 5, 6, 7, 8, 9.1, 9.3 a),
Annex I, 3.2 examiner/examining body
9.3 b), 10, 11
(according to 3.3 and 3.4) is a
notified body.

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) and services falling within
the scope of this standard.

5
 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Contents Page

Foreword ............................................................................................................................................................ iv 

Introduction ......................................................................................................................................................... v 
1  Scope ...................................................................................................................................................... 1 
2  Normative references ............................................................................................................................ 1 
3  Terms and definitions ........................................................................................................................... 2 
4  Reference numbers, symbols and abbreviated terms....................................................................... 4 
4.1  General ................................................................................................................................................... 4 
4.2  Reference numbers of welding processes ......................................................................................... 4 
4.3  Symbols and abbreviated terms .......................................................................................................... 4 
5  Essential variables and range of qualification ................................................................................... 6 
5.1  General ................................................................................................................................................... 6 
5.2  Welding processes ................................................................................................................................ 7 
5.3  Product type ........................................................................................................................................... 8 
5.4  Type of weld ........................................................................................................................................... 9 
5.5  Filler material grouping......................................................................................................................... 9 
5.6  Filler material type ............................................................................................................................... 10 
5.7  Dimensions .......................................................................................................................................... 11 
5.8  Welding positions................................................................................................................................ 13 
5.9  Weld details .......................................................................................................................................... 15 
6  Examination and testing ..................................................................................................................... 15 
6.1  Examination ......................................................................................................................................... 15 
6.2  Test pieces ........................................................................................................................................... 16 
6.3  Welding conditions ............................................................................................................................. 18 
6.4  Test methods ....................................................................................................................................... 18 
6.5  Test piece and test specimen ............................................................................................................ 19 
6.6  Test report ............................................................................................................................................ 23 
7  Acceptance requirements for test pieces ......................................................................................... 23 
8  Re-tests................................................................................................................................................. 24 
9  Period of validity.................................................................................................................................. 24 
9.1  Initial qualification ............................................................................................................................... 24 
9.2  Confirmation of the validity ................................................................................................................ 24 
9.3  Revalidation of welder qualification .................................................................................................. 24 
9.4  Revocation of qualification ................................................................................................................ 24 
10  Welder's qualification test certificate ................................................................................................ 25 
11  Designation .......................................................................................................................................... 25 
Annex A (informative) Welder's qualification test certificate ....................................................................... 27 
Annex B (informative) Job knowledge ............................................................................................................ 28 
Annex C (informative) FW/BW test assembly option .................................................................................... 31 
Bibliography ...................................................................................................................................................... 32 

© ISO 2012 – All rights reserved iii

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 9606-1 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 11, Qualification requirements for welding and allied processes personnel.

This second edition cancels and replaces the first edition (ISO 9606-1:1994), which has been technically
revised. It also incorporates the Amendment ISO 9606-1:1994/Amd.1:1998.

ISO 9606 consists of the following parts, under the general title Qualification testing of welders — Fusion
welding:

 Part 1: Steels

 Part 2: Aluminium and aluminium alloys

 Part 3: Copper and copper alloys

 Part 4: Nickel and nickel alloys

 Part 5: Titanium and titanium alloys, zirconium and zirconium alloys

Requests for official interpretations of any aspect of this part of ISO 9606 should be directed to the Secretariat
of ISO/TC 44/SC 11 via your national standards body. A complete listing of these bodies can be found
at www.iso.org.

iv © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Introduction
The ability of a welder to follow verbal or written instructions and verification of a person's skills are important
factors in ensuring the quality of the welded product.

The testing of a welder's skill in accordance with this International Standard depends on the welding
techniques and conditions used, in which uniform rules are complied with and standard test pieces are used.

The principle of this International Standard is that a qualification test qualifies a welder not only for the
conditions used in the test, but also for all other conditions which are considered easier to weld in accordance
with this International Standard. It is presumed that the welder has received training and/or has industrial
practice within the range of qualification.

The qualification test can be used to qualify a welding procedure and a welder provided that all the relevant
requirements, e.g. test piece dimensions and testing requirements are satisfied (see ISO 15614-1[11]).

All new qualifications shall be in accordance with each part of this International Standard from its date of issue.

At the end of its period of validity, existing qualification tests of welders in accordance with the requirement of
a national standard may be revalidated according to this International Standard. This is providing that the
technical intent of this International Standard is satisfied. It is necessary for the new range of qualification to
be interpreted in accordance with the requirements of this International Standard.

© ISO 2012 – All rights reserved v

BS EN ISO 9606‑1:2017
 BS EN ISO 9606‑1:2017
INTERNATIONAL STANDARD ISO 9606-1:2012(E)

Qualification testing of welders — Fusion welding —

Part 1:
Steels

1 Scope
This part of ISO 9606 specifies the requirements for qualification testing of welders for fusion welding of steels.

It provides a set of technical rules for a systematic qualification test of the welder, and enables such
qualifications to be uniformly accepted independently of the type of product, location and examiner or
examining body.

When qualifying welders, the emphasis is placed on the welder's ability manually to manipulate the electrode,
welding torch or welding blowpipe, thereby producing a weld of acceptable quality.

The welding processes referred to in this part of ISO 9606 include those fusion-welding processes which are
designated as manual or partly mechanized welding. It does not cover fully mechanized and automated
welding processes.

NOTE For such processes, see ISO 14732[10].

2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

ISO 857-1, Welding and allied processes — Vocabulary — Part 1: Metal welding processes

ISO 3834-2, Quality requirements for fusion welding of metallic materials — Part 2: Comprehensive quality
requirements

ISO 3834-3, Quality requirements for fusion welding of metallic materials — Part 3: Standard quality
requirements

ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers

ISO 5173, Destructive tests on welds in metallic materials — Bend tests

ISO 5817, Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding
excluded) — Quality levels for imperfections

ISO 6947, Welding and allied processes — Welding positions

ISO 9017, Destructive tests on welds in metallic materials — Fracture test

ISO/TR 15608, Welding — Guidelines for a metallic material grouping system

ISO 15609-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 1: Arc welding

© ISO 2012 – All rights reserved 1

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

ISO 15609-2, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 2: Gas welding

ISO 17636 (all parts), Non-destructive testing of welds — Radiographic testing

ISO 17637, Non-destructive testing of welds — Visual testing of fusion-welded joints

ISO/TR 25901:2007, Welding and related processes — Vocabulary

3 Terms and definitions

For the purposes of this part of ISO 9606, the following terms and definitions apply.

3.1
welder
person who holds and manipulates the electrode holder, welding torch or blowpipe by hand

[ISO/TR 25901:2007, 2.428]

3.2
manufacturer
person or organization responsible for the welding production

[ISO 15607:2003,[12] 3.23]

3.3
examiner
person appointed to verify compliance with the applicable standard

NOTE In certain cases, an external independent examiner can be required.

[ISO/TR 25901:2007, 2.119]

3.4
examining body
organization appointed to verify compliance with the applicable standard

NOTE In certain cases, an external independent examining body can be required.

[ISO/TR 25901:2007, 2.120]

3.5
material backing
backing using material for the purpose of supporting molten weld metal

3.6
gas backing
backing using gas primarily for the purpose of preventing oxidation

3.7
flux backing
backing using flux primarily for the purpose of preventing oxidation

NOTE In submerged arc welding, flux backing may also reduce the risk of a weld pool collapse.

3.8
consumable insert
filler material that is placed at the root of the joint before welding to be completely fused into the root

2 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

3.9
layer
stratum of weld metal consisting of one or more runs

[ISO/TR 25901:2007, 2.209]

3.10
root run
root pass
multi-layer welding run(s) of the first layer deposited in the root

[ISO/TR 25901:2007, 2.310]

3.11
filling run
multi-layer welding run(s) deposited after the root run(s) and before the capping run(s)

[ISO/TR 25901:2007, 2.132]

3.12
capping run
multi-layer welding run(s) visible on the weld face(s) after completion of welding

[ISO/TR 25901:2007, 2.57]

3.13
deposited thickness
thickness of the weld metal excluding any reinforcement

3.14
leftward welding
gas welding technique in which the filler rod is moved ahead of the blowpipe in relation to the welding direction

[ISO/TR 25901:2007, 2.210]

3.15
rightward welding
gas welding technique in which the filler rod is moved behind the blowpipe in relation to the welding direction

[ISO/TR 25901:2007, 2.302]

3.16
branch joint
joint of one or more tubular parts to the main pipe or to a shell

3.17
fillet weld
triangular weld in a square preparation for making a T-joint, corner joint or lap joint

[ISO/TR 25901:2007, 2.131]

3.18
verification
confirmation, through the provision of objective evidence, that specified requirements have been fulfilled

[ISO 9000:2005,[5] 3.8.4]

© ISO 2012 – All rights reserved 3

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

4 Reference numbers, symbols and abbreviated terms

4.1 General

The following abbreviations and reference numbers shall be used when completing the welder's qualification
test certificate (see Annex A).

4.2 Reference numbers of welding processes

This part of ISO 9606 covers the following manual or partly mechanized welding processes (reference
numbers of welding processes for symbolic representations are listed in ISO 4063):

111 manual metal arc welding

114 self-shielded tubular cored arc welding
121 submerged arc welding with solid wire electrode (partly mechanized)
125 submerged arc welding with tubular cored electrode (partly mechanized)
131 MIG welding with solid wire electrode
135 MAG welding with solid wire electrode
136 MAG welding with flux cored electrode
138 MAG welding with metal cored electrode
141 TIG welding with solid filler material (wire/rod)
142 autogenous TIG welding
143 TIG welding with tubular cored filler material (wire/rod)
145 TIG welding using reducing gas and solid filler material (wire/rod)
15 plasma arc welding
311 oxyacetylene welding

See ISO/TR 25901 and ISO 857-1 for the definition of manual and partly mechanized welding.

NOTE The principles of this part of ISO 9606 can be applied to other fusion welding processes.

4.3 Symbols and abbreviated terms

4.3.1 For test pieces

a design throat thickness

BW butt weld
D outside pipe diameter
FW fillet weld
l1 length of test piece
l2 half-width of test piece
lf examination length
P plate
s deposited thickness or fused metal thickness in butt welds
t material thickness of test piece (plate or wall thickness)

4 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

s1 deposited thickness of test piece for welding process 1

s2 deposited thickness of test piece for welding process 2
T pipe 1)
z leg length of fillet weld

4.3.2 For filler materials

nm no filler material

The symbol for type of covering or core is based on those given in various International Standards on filler
materials.

03 rutile basic covering

10 cellulosic covering
11 cellulosic covering
12 rutile covering
13 rutile covering
14 rutile + iron powder covering
15 basic covering
16 basic covering
18 basic + iron powder covering
19 limenite covering
20 iron oxide covering
24 rutile + iron powder covering
27 iron oxide + iron powder covering
28 basic + iron powder covering
45 basic covering
48 basic covering

A acid covering
B basic covering or electrode core — basic
C cellulosic covering
R rutile covering or electrode core — rutile, slow-freezing slag
RA rutile — acid covering
RB rutile — basic covering
RC rutile — cellulosic covering
RR rutile — thick covering

1) The word “pipe”, alone or in combination, is used to mean “pipe”, “tube” or “hollow section”.

© ISO 2012 – All rights reserved 5

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

M metal cored electrode or metal powder

P electrode core — rutile, fast-freezing slag
S solid wire electrode — solid rod
V electrode core — rutile or basic/fluoride
W electrode core — basic/fluoride, slow-freezing slag
Y electrode core — basic/fluoride, fast-freezing slag
Z electrode core — other types

4.3.3 For other weld details

fb flux backing
bs welding from both sides
ci consumable insert
lw leftward welding
mb material backing
gb gas backing
ml multi-layer
nb welding with no material backing
rw rightward welding
sl single layer
ss single side welding

4.3.4 For bend tests

A minimum tensile elongation after fracture required by the material specification

d diameter of the former or the inner roller
ts thickness of the bend test specimen

4.3.5 Types of arc welding

MAG metal active gas

MIG metal inert gas
TIG tungsten inert gas

5 Essential variables and range of qualification

5.1 General

The qualification of welders is based on essential variables. For each essential variable, a range of
qualification is defined. If the welder has to weld outside the range of welder qualification, a new qualification
test is required. The essential variables are:

 welding process(es);

 product type (plate or pipe);

6 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

 type of weld (butt or fillet);

 filler material group;

 filler material type;

 dimension (material thickness and outside pipe diameter);

 welding position;

 weld detail(s) (material backing, gas backing, flux backing, consumable insert, single side welding, both
side welding, single layer, multi-layer, leftward welding, rightward welding).

The parent material group(s) and subgroup(s), in accordance with ISO/TR 15608, that are used in the test
shall be recorded on the welder's qualification test certificate.

5.2 Welding processes

Welding processes are defined in ISO 857-1 and listed in 4.2.

Each test normally qualifies only one welding process. A change of welding process requires a new
qualification test.

Exceptions are as follows:

 a change from solid wire electrode 135 to a metal cored electrode 138, or vice versa, does not require
requalification (see Table 5);

 a change from solid wire electrode 121 to a tubular cored electrode 125, or vice versa, does not require
requalification (see Table 5);

 welding with 141, 143 or 145 qualifies for 141, 142, 143 and 145, but 142 only qualifies for 142;

 qualifying the welder for dip (short-circuit) transfer mode (131, 135 and 138) shall qualify him for other
transfer modes, but not vice versa.

However, it is permitted for a welder to be qualified for two or more welding processes by welding a single test
piece (multi-process joint) or by two or more separate qualification tests. The ranges of qualification
concerning the deposited thickness for each welding process used and for the multi-process joint for butt
welds are given in Tables 1 and 6.

© ISO 2012 – All rights reserved 7

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Table 1 — Deposited thickness range of weld metal for single and multi-process joints for butt welds

Deposited thickness range qualified

according to Table 6
Welding process used for test piece
Single process joint Multi-process
joint

for welding process 1:

s = s1
s = s1 + s2
for welding process 2:
s = s2

1 welding process 1 (ss nb)

2 welding process 2 (ss mb)

for welding process 1: for s = s1 + s2

s1
welding process 1
for welding process 2: only for welding of
s2 the root area

1 welding process 1
2 welding process 2
3 welding with backing (ss mb)
4 welding without backing (ss nb)

NOTE See 4.3.1 for definitions of the variables.

5.3 Product type

The qualification test shall be carried out on plate, pipe or other suitable product form. The following criteria
are applicable:

a) test piece welds with outside pipe diameter D  25 mm cover welds in plates;

b) test piece welds in plates cover welds in fixed pipe of outside pipe diameter D  500 mm; in accordance
with Tables 9 and 10.

c) test piece welds in plates cover welds in rotating pipes of outside pipe diameter D  75 mm for welding
positions PA, PB, PC, and PD; in accordance with Tables 9 and 10.

8 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

5.4 Type of weld

The qualification test shall be carried out as butt or fillet welding. The following criteria are applicable.

a) Butt welds cover butt welds in any type of joint except branch connections [see also c)].

b) Butt welds do not qualify fillet welds or vice versa. It is, however, permissible to qualify a fillet weld in
combination with a butt weld, e.g. single bevel joint preparation with permanent material backing (a
minimum test piece thickness of 10 mm shall be used). See Annex C.

For this combination test, all testing requirements specified in this part of ISO 9606 shall be fulfilled and
associated ranges of qualification shall be given based on the test conditions.

c) Butt welds in pipes qualify branch joints with an angle 60° and the same range of qualification as in
Tables 1 to 12. For a branch weld, the range of qualification is based on the outside diameter of the
branch.

d) For applications where the type of weld cannot be qualified by means of either a butt or fillet or for branch
connections of less than 60°, a specific test piece should be used to qualify the welder, when specified
(e.g. by the product standard).

e) Butt welds may qualify fillet welds if a supplementary fillet weld test piece (see Figure 3) is welded with
each process, filler material (FM) group and electrode covering/core, in accordance with Tables 3, 4,
and 5. The test piece shall be at least 10 mm thick, or the thickness of the butt weld test piece if the
thickness is less, and completed using a single layer in the PB position. For this supplementary test, the
welder shall be qualified for all fillet welds as given for the butt weld qualification variables related to the
range of qualification for fillet welds (e.g. Tables 7, 8, 9, 10 and 12). Fillet weld positions PA and PB are
qualified by this test.

5.5 Filler material grouping

5.5.1 General

The qualification test shall be carried out with filler material from one of the groups listed in Table 2. When
welding with filler materials outside the filler material grouping in Table 2, a separate test is required.

The parent material used in a qualification test should be from any suitable material from ISO/TR 15608,
material groups 1 to 11.

5.5.2 Range of qualification

Filler material groups are defined in Table 2.

Table 2 — Filler material grouping

Group Filler material for welding of Examples of applicable standards

FM1 Non-alloy and fine grain steels ISO 2560,[2] ISO 14341,[8] ISO 636,[1] ISO 14171,[6]
ISO 17632[14]
FM2 High-strength steels ISO 18275,[21] ISO 16834,[13] ISO 26304,[25] ISO 18276[22]
FM3 Creep-resisting steels Cr  3,75 % ISO 3580,[3] ISO 21952,[23] ISO 24598,[24] ISO 17634[16]
FM4 Creep-resisting steels 3,75  Cr  12 % ISO 3580,[3] ISO 21952,[23] ISO 24598,[24] ISO 17634[16]
FM5 Stainless and heat-resisting steels ISO 3581,[4] ISO 14343,[9] ISO 17633[15]
FM6 Nickel and nickel alloys ISO 14172,[7] ISO 18274[20]

© ISO 2012 – All rights reserved 9

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Welding with a filler material in one group qualifies the welder for welding with all other filler materials within
the same group, as well as other groups, listed in Table 3, and welding on parent materials from groups 1
to 11.

Table 3 — Range of qualification for filler material

Range of qualification
Filler material
FM1 FM2 FM3 FM4 FM5 FM6

FM1   — — — —
FM2   — — — —
FM3    — — —
FM4     — —
FM5 — — — —  —
FM6 — — — —  

 indicates those filler materials for which the welder is qualified.

— indicates those filler materials for which the welder is not qualified.

5.6 Filler material type

Welding with filler material qualifies for welding without filler material, but not vice versa.

NOTE For processes 142 and 311 (without filler material), the parent material group used in the test is the material
group that the welder is qualified for.

The ranges of qualification for filler material type are given in Tables 4 and 5.

Table 4 — Range of qualification for covered electrodesa

Range of qualification
Welding Type of covering
A, RA, RB, RC, RR, R B C
process used in the testb
03, 13, 14, 19, 20, 24, 27 15, 16, 18, 28, 45, 48 10, 11

A, RA, RB, RC, RR, R

 — —
03, 13, 14, 19, 20, 24, 27
B
111   —
15, 16, 18, 28, 45, 48
C
— — 
10, 11

 indicates those filler material types for which the welder is qualified.
— indicates those filler material types for which the welder is not qualified.
a For abbreviations, see 4.3.2.
b The type of covering used in the qualification test of welders for root run welding without backing (ss nb) is the type of covering
qualified for root run welding in production with no backing (ss nb).

10 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

a,b
Table 5 — Range of qualification for filler material types

Range of qualification
Filler material types used in test piece
S M B R, P, V, W, Y, Z
Solid wire electrode, rod (S)   — —
Metal cored electrode, rod (M)   — —
Flux cored electrode, rod (B) — —  
Flux cored electrode, rod (R, P, V, W, Y, Z) — — — 

 indicates those filler material types for which the welder is qualified.
— indicates those filler material types for which the welder is not qualified.
a For abbreviations, see 4.3.2.
b The type of flux cored wire used in the qualification test of welders for root run welding without backing (ss, nb) is the type of flux
cored wire qualified for root run welding in production with no backing (ss, nb).

5.7 Dimensions

The welder qualification test of butt welds is based on the deposited thickness and outside pipe diameters.
The ranges of qualification are specified in Tables 6 and 7.

It is not intended that deposited thickness or outside pipe diameters should be measured precisely, but rather
the general philosophy behind the values given in Tables 6 and 7 should be applied.

For fillet welds, the range of qualification for material thicknesses is specified in Table 8.

For test pieces of different outside pipe diameters and deposited thicknesses, the welder is qualified for:

 the thinnest through to the thickest deposited and/or parent metal thickness qualified; and

 the smallest through to the largest diameter qualified (refer to Tables 6 and 7).

Table 6 — Range of qualification of deposited thickness for butt welds

Dimensions in millimetres

Deposited thickness of test piece Range of qualificationa,b

s

s to 3c
or
s3 s to 2sc
whichever is greater
3  s < 12 3 to 2sd

s  12e,f 3f
a For single process and the same type of filler material, s, is equal to parent material t.
b For branch joints, the range of qualification for deposited thickness is:
— for set-on branch, see, for example, Figure 1 a), the deposited thickness of the branch;
— for set-through and set-in branches, see, for example, Figure1 b) and c), the deposited thickness of the main pipe or shell.
c For oxyacetylene welding (311): s to 1,5s
d For oxyacetylene welding (311): 3 to 1,5s
e The test piece has to be welded in at least 3 layers
f For multi-processes, s is the deposited thickness for each process.

© ISO 2012 – All rights reserved 11

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

a) Set-on b) Set-through

c) Set-in

Key
D outside pipe diameter
s deposited thickness or fused metal thickness in butt welds
t material thickness of test piece (plate or wall thickness)
1 branch
2 main pipe or shell

Figure 1 — Branch types

Table 7 — Range of qualification for outside pipe diameter

Dimensions in millimetres

Outside pipe diameter of test piecea

Range of qualification
D

D  25 D to 2D

D  25  0,5D (25 mm min.)

a For non-circular hollow sections, D is the dimension of the smaller side.

Table 8 — Range of qualification of material thickness for fillet welds

Dimensions in millimetres
Material thickness of test piece
Range of qualification
t

t3 t to 2t, or 3, whichever is greater

t3 3

12 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

In the case of branch welding, the deposited thickness criteria to which Table 6 applies and the outside pipe
diameter criteria to which Table 7 applies are as follows:

 set-on: the deposited thickness and outside pipe diameter of the branch [see Figure 1 a)];

 set-in or set-through: the deposited thickness of the main pipe or shell and the outside pipe diameter of
the branch [see Figure 1 b) and c)].

5.8 Welding positions

The range of qualification for each welding position is given in Tables 9 and 10. The welding positions and
symbols refer to ISO 6947.

The test pieces shall be welded in accordance with the testing positions specified in ISO 6947.

Welding two pipes with the same outside pipe diameter, one in welding position PH and one in welding
position PC, also covers the range of qualification of a pipe welded in welding position H-L045 using upward
welding.

Welding two pipes with the same outside pipe diameter, one in welding position PJ and one in welding
position PC, also covers the range of qualification of a pipe welded in welding position J-L045 using downward
welding.

Outside pipe diameters D  150 mm can be welded in two welding positions (PH or PJ 2/3 of circumference,
PC 1/3 of circumference) using only one test piece. This test covers all positions for the direction of welding
used in the test.

NOTE For welding position symbols, refer to ISO 6947.

Figure 2 — Outside pipe diameter D  150 mm, positions

© ISO 2012 – All rights reserved 13

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Table 9 — Range of qualification for welding positions for butt welds

Range of qualification
Testing position PA PC PE PF PG
Flat Horizontal Overhead Vertical up Vertical down
PA  — — — —

PC   — — —

PE (plate)    — —

PF (plate)  — —  —

PH (pipe)  —   —

PG (plate) — — — — 
PJ (pipe)  —  — 
H-L045     —

J-L045    — 

NOTE See also 5.3.

 indicates those welding positions for which the welder is qualified.

— indicates those welding positions for which the welder is not qualified.

Table 10 — Range of qualification for welding positions for fillet welds

Range of qualification
Testing position PA PB PC PD PE PF PG
Flat Horizontal Horizontal Overhead Overhead Vertical up Vertical down
PA  — — — — — —
PB   — — — — —
PC    — — — —
PD      — —
PE (plate)      — —
PF (plate)   — — —  —
PH (pipe)       —
PG (plate) — — — — — — 
PJ (pipe)   —   — 

NOTE See also 5.3.

 indicates those welding positions for which the welder is qualified.

— indicates those welding positions for which the welder is not qualified.

14 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

5.9 Weld details

Depending on the weld details, the ranges of qualification are shown in Tables 11 and 12.

When welding with process 311, a change from rightward welding to leftward welding, and vice versa,
requires a new qualification test.

Table 11 — Range of qualification for backings and consumable inserts

Range for qualification for backing and consumable inserts

Test condition No Material Welding from Gas Consumable Flux

backing backing both sides backing insert backing
(ss,nb) (ss,mb) (bs) (ss,gb) (ci) (ss,fb)
No backing (ss,nb)     — 
Material backing (ss,mb) —   — — —
Welding from both sides (bs) —   — — —
Gas backing (ss,gb) —    — —
Consumable insert (ci) —   —  —
Flux backing (ss,fb) —   — — 

 indicates those conditions for which the welder is qualified.

— indicates those conditions for which the welder is not qualified.

Table 12 — Range of qualification of layer technique for fillet welds

Range of qualificationb
Test piece Single layer Multi-layer
(sl) (ml)
Single layer (sl)  —

Multi-layer (ml)a  

 indicates the layer technique for which the welder is qualified.

— indicates the layer technique for which the welder is not qualified.
a During the welding of the test piece, the examiner shall perform visual examination of the first layer in accordance with Clause 7.
b When a welder has been qualified using a multi-layer butt weld and he or she makes the supplementary fillet weld test described in
5.4 e), he or she is qualified for both multi- and single layer fillet welds.

6 Examination and testing

6.1 Examination

The welding of test pieces shall be witnessed by the examiner or examining body. The testing shall be verified
by the examiner or examining body.

The test pieces shall be marked with the identification of the examiner and the welder. Additionally, welding
positions for all test pieces shall be marked on the test piece and, for fixed pipe welds, the 12 o'clock welding
position shall also be marked.

© ISO 2012 – All rights reserved 15

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

The examiner or examining body may stop the test if the welding conditions are not correct or if it appears that
the welder does not have the skill to fulfil the requirements, e.g. where there are excessive and/or systematic
repairs.

6.2 Test pieces

The shape and dimension of test pieces required are shown in Figures 3 to 6.

A minimum test piece length for plates of 200 mm is required; the examination length is 150 mm. For pipe
circumferences of less than 150 mm, additional test pieces will be required with a maximum of three test
pieces.

Dimensions in millimetres

Key
t material thickness of test piece

Figure 3 — Dimensions of test piece for a butt weld in plate

16 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Dimensions in millimetres

Key
t material thickness of test piece

NOTE The parent material can be of dissimilar thickness.

Figure 4 — Dimensions of test piece for a fillet weld on plate

Dimensions in millimetres

Key
D outside pipe diameter
t material thickness of test piece (wall thickness)

Figure 5 — Dimensions of test piece for a butt weld in pipe

© ISO 2012 – All rights reserved 17

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Dimensions in millimetres

Key
D outside pipe diameter
l1 length of test piece
t material thickness of test piece (plate or wall thickness)

NOTE The parent material can be of dissimilar thickness for the pipe and plate.

Figure 6 — Dimensions of test piece for a fillet weld on pipe

6.3 Welding conditions

The qualification test of welders shall follow a pWPS or WPS prepared in accordance with ISO 15609-1 or
ISO 15609-2. The required throat thickness of the fillet weld test piece shall be defined in the pWPS or WPS
used for the test.

The following welding conditions shall apply.

 The test piece shall have at least one stop and restart in the root run and in the capping run. When more
than one process is used, then at least one stop and restart shall be carried out for each process, this
includes the root run and final run. The stop and restart areas shall be marked.

 The welder shall be allowed to remove minor imperfections by grinding, except for the capping run for
which only the stop and restart may be ground. The permission of the examiner or examining body shall
be obtained.

 Any post-weld heat treatment required in the pWPS or WPS may be omitted at the discretion of the
manufacturer.

6.4 Test methods

After welding the test piece shall be tested in accordance with Table 13.

If the weld is accepted by visual testing, the remaining test(s) according to Table 13 shall be carried out.

When material backing is used in the qualification test, it shall be removed prior to destructive testing (except
for macroscopic examination) and need not be removed before non-destructive testing (NDT).

The test specimen for macroscopic examination shall be prepared and etched on one side to clearly reveal
the weld. Polishing is not required.

18 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Table 13 — Test methods

Butt weld
Test method Fillet weld and branch joint
(in plate or pipe)

Visual testing according to ISO 17637 mandatory mandatory

Radiographic testing according to ISO 17636 mandatorya,b,c not mandatory

Bend test according to ISO 5173 mandatorya,b,d not applicable

Fracture test according to ISO 9017 mandatorya,b,d mandatorye,f

a Either radiographic testing or bend or fracture tests shall be used.
b When radiographic testing is used, then additional bend or fracture tests are mandatory for welding processes 131, 135, 138
and 311.
c The radiographic testing may be replaced by ultrasonic testing according to ISO 17640[19] for thicknesses 8 mm on ferritic steels
only. In this case, the additional tests mentioned in footnote b are not required.
d For outside pipe diameters D  25 mm, the bend or fracture tests may be replaced by a notched tensile test of the complete test
piece (an example is given in Figure 9).
e The fracture tests may be replaced by a macroscopic examination, performed according to ISO 17639[18], of at least two
sections,at least one of which shall be taken from the stop/start location.
f The fracture tests on pipes may be replaced by radiographic testing.

6.5 Test piece and test specimen

6.5.1 General

In 6.5.2 and 6.5.3, details of the type, dimensions, and preparation of the test pieces and test specimens are
given. In addition, the requirements for destructive tests are indicated. For root, face or side bend, or
fracture tests, one specimen shall be taken from the start and stop area in the examination length.

6.5.2 Butt weld in plate and pipe

6.5.2.1 General

When radiographic testing is used, the examination length of the weld (see Figures 7 and 8) in the test piece
shall be radiographed.

When fracture testing is used, test specimens may be longitudinally notched in the centre of the weld of the
side in tension in order to achieve a fracture in the weld. All notch preparations according to ISO 9017 are
permitted.

All test specimens shall be tested in such a manner that fracture is reached and the specimen examined after
fracture.

6.5.2.2 Fracture testing only

For butt welds in plate, the test piece examination length (Figure 7) shall be cut into four test specimens of
equal width in accordance with the dimensions given in Table 14.

For butt welds in pipe, the test piece examination length (Figure 8) shall be cut into four test specimens of
equal width in accordance with the dimensions given in Table 14.

© ISO 2012 – All rights reserved 19

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Dimensions in millimetres

Key
l1 length of test piece
l2 half-width of test piece
lf examination length

Figure 7 — Examination length for fracture test specimens for a butt weld in plate

Key
lf examination length
1 one root fracture or one root transverse bend or one side-bend test specimen
2 one face fracture or one face transverse bend or one side-bend test specimen
3 one root fracture or one root transverse bend or one side-bend test specimen
4 one face fracture or one face transverse bend or one side-bend test specimen

Figure 8 — Examination length and locations for fracture

or bend test specimens for a butt weld in pipe

20 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Table 14 — Width of fracture test specimens

Dimensions in millimetres

Product type
a
Width of fracture test specimens
Plates (P) Outside diameter, D, of pipes (T)

 100 35
— 50  D  100 20
— 25  D  50 10
a For pipes with outside diameter D  25 mm, the notch tensile test piece according to Figure 9 is recommended.

Dimensions in millimetres

Key
d diameter of the former or the inner roller

Holes are not allowed in start and stop areas.

For t  1,8 mm: d  4,5 mm
For t  1,8 mm: d  3,5 mm

NOTE Notch profiles s and q are also permitted in circumferential direction according to ISO 9017.

Figure 9 — Example for notch tensile test for pipe test piece outside diameter 25 mm

6.5.2.3 Bend testing only

Bend tests shall be performed in accordance with ISO 5173.

When only bend testing is carried out, the following conditions shall apply.

For thicknesses t  12 mm, a minimum of two root and two face bend test specimens shall be used, and the
complete examination length shall be tested.

For thicknesses t  12 mm, four side-bend test specimens shall be used approximately equally spaced along
the examination length.

For pipe butt welds, the four specimens shall be equally spaced in accordance with Figure 8.

In all cases, at least one specimen shall be taken from a stop/start location. For this purpose, it is possible that
a side-bend specimen can be substituted by a root-bend specimen.

© ISO 2012 – All rights reserved 21

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

When transverse bend testing or side-bend testing is used, the diameter of the former or the inner roller shall
be 4t and the bending angle 180° for parent metal with elongation A  20 %. For parent metal with elongation
A  20 %, the following equation shall apply:

100  t s
d  ts
A

where

d is the diameter of the former or the inner roller, in millimetres;

ts is the thickness of the bend-test specimen, in millimetres;

A is the minimum percentage elongation required by the material standard.

6.5.2.4 Additional bend or fracture test

When additional bend or fracture tests are required (see Table 13, footnote b), in all cases, at least one
specimen shall be taken from a stop/start location. For this purpose, it is possible that a side-bend specimen
can be substituted by a root-bend specimen.

 For all plate butt welds, one root and one face test specimen shall be tested or two side-bend test
specimens if applicable.

 For butt welds in pipe in PA or PC positions, one root and one face test specimen shall be tested or two
side-bend test specimens, if applicable.

 For butt welds in pipe welded in all other welding positions, one root-test specimen shall be taken from
the PE (overhead) welding position and one face test specimen shall be taken from the PF (vertical up)
position or the PG (vertical down) position, or two side-bend test specimens if applicable.

6.5.3 Fillet weld on plate and pipe

For fillet welds on plate, the test piece examination length (Figure 10) shall be fractured as one complete
specimen. If necessary, the test piece can be cut into several test specimens of equal width.

For fillet welds on pipe, the test piece shall be cut into four or more test specimens and fractured.

Fillet weld fracture tests on plate and pipe may be replaced by macroscopic examination. When macroscopic
examination is used, at least two specimens shall be taken. One macroscopic specimen shall be taken at the
stop/start location.

Fillet weld test specimens shall be positioned for breaking in accordance with ISO 9017.

22 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Dimensions in millimetres

Key
lf examination length

Figure 10 — Examination length for fracture testing for a fillet weld in plate

6.6 Test report

The results of all testing shall be documented in accordance with the relevant test standard.

7 Acceptance requirements for test pieces

Test pieces shall be evaluated according to the acceptance requirements specified for relevant types of
imperfections.

Prior to any testing, the following shall be checked:

 all slag and spatters are removed;

 no grinding on the root and the face side of the weld (according to 6.3);

 stop and restart in the root run and in the capping run are identified (according to 6.3);

 profile and dimensions.

The acceptance requirements for imperfections found by test methods performed according to this part of
ISO 9606 shall, unless otherwise specified, be assessed in accordance with ISO 5817. A welder is qualified if
the imperfections are within ISO 5817, quality level B, except for the following imperfection types for which
level C shall apply: excess weld metal (502); excessive convexity (503); excessive throat thickness (5214);
excessive penetration (504); and undercut (501).

Bend-test specimens shall not reveal any discrete discontinuity 3 mm in any direction. Discontinuities
appearing at the edges of a test specimen during testing shall be ignored in the evaluation unless there is
evidence that cracking is due to incomplete penetration, slag or other discontinuity. The sum of the greatest
discontinuities exceeding 1 mm but less than 3 mm in any one bend specimen shall not exceed 10 mm.

If the imperfections in the welder's test piece exceed the permitted maximum specified, then the welder fails
the test.

Reference should also be made to the corresponding acceptance criteria for non-destructive testing. Specified
procedures shall be used for all destructive and non-destructive testing.

© ISO 2012 – All rights reserved 23

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

8 Re-tests
If any test fails to comply with the requirements of this part of ISO 9606, the welder may be given the
opportunity to repeat the qualification test once without further training.

9 Period of validity

9.1 Initial qualification

The welder's qualification begins from the date of welding of the test piece(s), provided that the required
testing has been carried out and the test results obtained were acceptable. The certificate needs to be
confirmed every 6 months otherwise the certificate(s) become(s) invalid.

The validity of the certificate may be extended as specified in 9.3. The chosen method of the extension of
qualification in accordance with 9.3, a) or b) or c), shall be stated on the certificate at the time of issue.

9.2 Confirmation of the validity

The qualifications of a welder for a process shall be confirmed every 6 months by the person responsible for
welding activities or examiner/examining body. This is confirming that the welder has worked within the range
of qualification and extends the validity of the qualification for a further 6 month period.

This subclause is applicable to all options of revalidation specified in 9.3.

9.3 Revalidation of welder qualification

Revalidation shall be carried out by an examiner/examining body.

The skill of the welder shall be periodically verified by one of the following methods.

a) The welder shall be retested every 3 years.

b) Every 2 years, two welds made during the last 6 months of the validity period shall be tested by
radiographic or ultrasonic testing or destructive testing and shall be recorded. The acceptance levels for
imperfections shall be as specified in Clause 7. The weld tested shall reproduce the original test
conditions except for thickness and outside diameter. These tests revalidate the welder's qualifications for
an additional 2 years.

c) A welder's qualifications for any certificate shall be valid as long as it is confirmed according to 9.2 and
provided all the following conditions are fulfilled:

 the welder is working for the same manufacturer for whom he or she qualified, and who is
responsible for the manufacture of the product;

 the manufacturer's quality programme has been verified in accordance with ISO 3834-2 or
ISO 3834-3;

 the manufacturer has documented that the welder has produced welds of acceptable quality based
on application standards; the welds examined shall confirm the following conditions: welding
position(s), weld type (FW, BW), material backing (mb) or no material backing (nb).

9.4 Revocation of qualification

When there is a specific reason to question a welder's ability to make welds that meet the product standard
quality requirements, the qualifications that support the welding he or she is doing shall be revoked. All other
qualifications not questioned remain valid.

24 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

10 Welder's qualification test certificate

It shall be verified that the welder has successfully passed the qualification test. All essential variables shall be
recorded on the certificate. If the test piece(s) fail(s) any of the required tests, no certificate shall be issued.

The certificate shall be issued under the sole responsibility of the examiner or examining body. A
recommended format is detailed in Annex A. If any other form of welder's qualification test certificate is used,
it shall contain the information required in Annex A. The examiner or examining body is responsible for
verifying that all essential variables are addressed in this certificate.

The following non-essential variables shall be recorded on the certificate:

 type of current and polarity;

 parent material group/subgroup;

 shielding gas.

In general, for each test piece, a separate welder's qualification test certificate shall be issued.

If more than one test piece is welded, a single welder's qualification test certificate can be issued that
combines the ranges of qualification of the individual test pieces. All essential variables for all tests shall be
recorded on the combined certificate. In this case, only one of the following essential variables is permitted to
differ, except those given in 5.7.

 type of weld,

 welding position,

 deposited thickness.

It is not permissible to change other essential variables.

It is recommended that the welder's qualification test certificates be issued in the local language plus at least
one of the following languages: English, French or German.

The examination of job knowledge (see Annex B) shall be designated by “Accepted” or “Not tested”.

In accordance with 5.4 e) the supplementary fillet weld test shall be recorded on the certificate for the
associated butt weld qualification.

11 Designation
The designation of a welder qualification shall comprise the following items in the order given (the system is
arranged so that it can be used for computerization):

a) the number of this part of ISO 9606 (ISO 9606-1);

b) the essential variables:

1) welding processes: refer to 4.2, 5.2, and ISO 4063,

2) product type: plate (P), pipe (T), refer to 4.3.1 and 5.3,

3) type of weld: butt weld (BW), fillet weld (FW), refer to 5.4,

4) filler material group or parent material group (autogenous welding): refer to 5.5,

© ISO 2012 – All rights reserved 25

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

5) filler material types: refer to 5.6,

6) dimensions of test piece: deposited thickness, s, or material thickness, t, and outside pipe diameter,
D, refer to 5.7,

7) welding positions: refer to 5.8 and ISO 6947,

8) weld details: refer to 5.9.

The type of shielding and backing gas shall not be incorporated in the designation, but shall be included in the
welder's qualification test certificate (see Annex A).

26 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Annex A
(informative)

Welder's qualification test certificate

Designation(s): ................................................................................................................
................................................................................................................
WPS – Reference: Examiner or examining body – Reference No.:
Welder's name:
Identification:
Method of identification: Photograph
Date and place of birth: (if required)
Employer:
Code/testing standard:
Job knowledge: Acceptable/Not tested (delete as necessary)
Test piece Range of qualification
Welding process(es);
Transfer mode
Product type (plate or pipe)
Type of weld
Parent material group(s)/subgroups
Filler material group(s)
Filler material (Designation)
Shielding gas
Auxiliaries ------------------------
Type of current and polarity ------------------------
Material thickness (mm)
Deposited thickness (mm)
Outside pipe diameter (mm)
Welding position
Weld details
Multi-layer/single layer
Supplementary fillet weld test (completed in conjunction with a butt weld qualification): acceptable/not acceptable
Type of test Performed and accepted Not tested Name of examiner or
Visual testing examining body:
Radiographic testing Place, date and signature
of examiner or examining
Fracture test body:
Bend test Date of issue: 2007-01-20
Notch tensile test
Macroscopic examination

Revalidation Valid until Revalidation Valid until Revalidation Valid until

9.3 a) 2010-01-20 9.3 b) 2009-01-20 9.3 c) 2007-07-20
Revalidation for qualification by examiner or examining body for the following 2 years [refer to 9.3 b)]
Date Signature Position or title

Confirmation of the validity by employer/welding coordinator/examiner or examining body for the following 6 months [refer to
9.2)]
Date Signature Position or title

© ISO 2012 – All rights reserved 27

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Annex B
(informative)

Job knowledge

B.1 General
The test of job knowledge is recommended, but it is not mandatory.

However, some countries may require that the welder undergo a test of job knowledge. If the job knowledge
test is carried out, it should be recorded on the welder's qualification test certificate.

This annex outlines the job knowledge that a welder should have in order to ensure that procedures are
followed and common practices are complied with. The job knowledge indicated in this annex is only pitched
at the most basic level.

Owing to different training programmes in various countries, it is only proposed to standardize general
objectives or categories of job knowledge. The actual question used should be drawn up in the individual
country concerned, but should include questions on areas covered in B.2, relevant to the qualification test of
welders.

The actual tests of a welder's job knowledge may be given by any of the following methods or combinations of
these methods:

a) written objective tests (multiple choice);

b) oral questioning following a set of written questions;

c) computer testing;

d) demonstration/observation testing following a written set of criteria.

The test of job knowledge is limited to the matters related to the welding process used in the test.

B.2 Requirements

B.2.1 Welding equipment

B.2.1.1 Oxyacetylene welding

a) Identification of gas cylinders.

b) Identification and assembly of essential components.

c) Selection of correct nozzles and welding blowpipes.

B.2.1.2 Arc welding

a) Construction and maintenance of welding equipment and typical parameters.

b) Type of welding current.

c) Correct connection of the welding return cable.

28 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

B.2.2 Welding process 2)

B.2.2.1 Oxyacetylene welding (311)

a) Gas pressure.

b) Selection of nozzle type.

c) Type of gas flame.

d) Effect of overheating.

B.2.2.2 Manual metal-arc welding with covered electrode (111)

a) Classification of electrodes.

B.2.2.3 Gas and self-shielded metal-arc welding (114, 13, 14, 15)

a) Type and size of electrodes.

b) Identification of shielding gas and flow rate (without 114).

c) Type, size and maintenance of nozzles/contact tip.

d) Selection and limitations of transfer mode.

e) Protection of the welding arc from draughts.

B.2.2.4 Submerged arc welding (121, 125)

a) Drying, feeding and correct recovery of flux.

b) Correct alignment and travel of welding head.

B.2.3 Parent metals

a) Identification of material.

b) Methods and control of pre-heating.

c) Control of interpass temperature.

B.2.4 Filler metal types

a) Identification of filler metal types.

b) Storage, handling and conditions of filler metal types.

c) Selection of correct size.

d) Cleanliness of electrodes and filler wires.

e) Control of wire spooling.

f) Control and monitoring of gas flow rates.

2) The numbers refer to ISO 4063.

© ISO 2012 – All rights reserved 29

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

B.2.5 Safety precautions

B.2.5.1 General

a) Safe assembly, set-up and turn-off procedures.

b) Safe control of welding fumes and gases.

c) Personal protection.

d) Fire hazards.

e) Welding in confined spaces.

f) Awareness of welding environment.

B.2.5.2 Oxyacetylene welding

a) Safe storage, handling and use of compressed gases.

b) Leak detection on gas hoses and fittings.

c) Procedure to be taken in the event of a flashback.

B.2.5.3 All arc welding processes

a) Environment of increased hazard electric shock.

b) Radiation from the arc.

c) Effects of stray arcing.

B.2.5.4 Gas-shielded metal-arc welding

a) Safe storage, handling and use of compressed gases.

b) Leak detection on gas hoses and fittings.

B.2.6 Welding sequences/procedures

Appreciation of welding procedure requirements and the influence of welding parameters.

B.2.7 Joint preparation and weld representation

a) Conformity of joint preparation to the welding procedure specification (WPS).

b) Cleanliness of fusion faces.

B.2.8 Weld imperfections

a) Identification of imperfections.

b) Causes.

c) Prevention and remedial action.

B.2.9 Welder qualification

The welder shall be aware of the range of the qualification.

30 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Annex C
(informative)

FW/BW test assembly option

See Figure C.1.

Dimensions in millimetres

a Gap.

Figure C.1 — Combined FW/BW test piece

© ISO 2012 – All rights reserved 31

BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

Bibliography

[1] ISO 636, Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-
alloy and fine-grain steels — Classification

[2] ISO 2560, Welding consumables — Covered electrodes for manual metal arc welding of non-alloy and
fine grain steels — Classification

[3] ISO 3580, Welding consumables — Covered electrodes for manual metal arc welding of creep-
resisting steels — Classification

[4] ISO 3581, Welding consumables — Covered electrodes for manual metal arc welding of stainless and
heat-resisting steels — Classification

[5] ISO 9000:2005, Quality management systems — Fundamentals and vocabulary

[6] ISO 14171, Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode/flux
combinations for submerged arc welding of non alloy and fire grain steels — Classification

[7] ISO 14172, Welding consumables — Covered electrodes for manual metal arc welding of nickel and
nickel alloys — Classification

[8] ISO 14341, Welding consumables — Wire electrodes and weld deposits for gas shielded metal arc
welding of non alloy and fine grain steels — Classification

[9] ISO 14343, Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding
of stainless and heat resisting steels — Classification

[10] ISO 14732, Welding personnel — Qualification testing of welding operators for fully mechanized
welding and weld setters for fully mechanized welding and automatic welding of metallic materials

[11] ISO 15614-1, Specification and qualification of welding procedures for metallic materials — Welding
procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys

[12] ISO 15607, Specification and qualification of welding procedures for metallic materials — General
rules

[13] ISO 16834, Welding consumables — Wire electrodes, wires, rods and deposits for gas-shielded arc
welding of high strength steels — Classification

[14] ISO 17632, Welding consumables — Tubular cored electrodes for gas shielded and non-gas shielded
metal arc welding of non-alloy and fine grain steels — Classification

[15] ISO 17633, Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas
shielded metal arc welding of stainless and heat-resisting steels — Classification

[16] ISO 17634, Welding consumables — Tubular cored electrodes for gas shielded metal arc welding of
creep-resisting steels — Classification

[17] ISO 17635, Non-destructive testing of welds — General rules for metallic materials

[18] ISO 17639, Destructive tests on welds in metallic materials — Macroscopic and microscopic
examination of welds

[19] ISO 17640, Non-destructive testing of welds — Ultrasonic testing — Techniques, testing levels, and
assessment

32 © ISO 2012 – All rights reserved

 BS EN ISO 9606‑1:2017
ISO 9606-1:2012(E)

[20] ISO 18274, Welding consumables — Solid wire electrodes, solid strip electrodes, solid wires and solid
rods for fusion welding of nickel and nickel alloys — Classification

[21] ISO 18275, Welding consumables — Covered electrodes for manual metal arc welding of high-
strength steels — Classification

[22] ISO 18276, Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded
metal arc welding of high-strength steels — Classification

[23] ISO 21952, Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc
welding of creep-resisting steels — Classification

[24] ISO 24598, Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode-flux
combinations for submerged arc welding of creep-resisting steels — Classification

[25] ISO 26304, Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode-flux
combinations for submerged arc welding of high strength steels — Classification

© ISO 2012 – All rights reserved 33

This page deliberately left blank
This page deliberately left blank
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

British Standards Institution (BSI)

BSI is the national body responsible for preparing British Standards and other
standards-related publications, information and services.
BSI is incorporated by Royal Charter. British Standards and other standardization
products are published by BSI Standards Limited.

About us Reproducing extracts

We bring together business, industry, government, consumers, innovators For permission to reproduce content from BSI publications contact the BSI
and others to shape their combined experience and expertise into standards Copyright & Licensing team.
-based solutions.
The knowledge embodied in our standards has been carefully assembled in Subscriptions
a dependable format and refined through our open consultation process. Our range of subscription services are designed to make using standards
Organizations of all sizes and across all sectors choose standards to help easier for you. For further information on our subscription products go to
them achieve their goals. bsigroup.com/subscriptions.
With British Standards Online (BSOL) you’ll have instant access to over 55,000
Information on standards British and adopted European and international standards from your desktop.
We can provide you with the knowledge that your organization needs It’s available 24/7 and is refreshed daily so you’ll always be up to date.
to succeed. Find out more about British Standards by visiting our website at You can keep in touch with standards developments and receive substantial
bsigroup.com/standards or contacting our Customer Services team or discounts on the purchase price of standards, both in single copy and subscription
Knowledge Centre. format, by becoming a BSI Subscribing Member.
PLUS is an updating service exclusive to BSI Subscribing Members. You will
Buying standards
automatically receive the latest hard copy of your standards when they’re
You can buy and download PDF versions of BSI publications, including British revised or replaced.
and adopted European and international standards, through our website at
To find out more about becoming a BSI Subscribing Member and the benefits
bsigroup.com/shop, where hard copies can also be purchased.
of membership, please visit bsigroup.com/shop.
If you need international and foreign standards from other Standards Development
With a Multi-User Network Licence (MUNL) you are able to host standards
Organizations, hard copies can be ordered from our Customer Services team.
publications on your intranet. Licences can cover as few or as many users as you
wish. With updates supplied as soon as they’re available, you can be sure your
Copyright in BSI publications
documentation is current. For further information, email subscriptions@bsigroup.com.
All the content in BSI publications, including British Standards, is the property
of and copyrighted by BSI or some person or entity that owns copyright in the Revisions
information used (such as the international standardization bodies) and has
Our British Standards and other publications are updated by amendment or revision.
formally licensed such information to BSI for commercial publication and use.
We continually improve the quality of our products and services to benefit your
Save for the provisions below, you may not transfer, share or disseminate any
business. If you find an inaccuracy or ambiguity within a British Standard or other
portion of the standard to any other person. You may not adapt, distribute,
BSI publication please inform the Knowledge Centre.
commercially exploit, or publicly display the standard or any portion thereof in any
manner whatsoever without BSI’s prior written consent.
Useful Contacts
Storing and using standards Customer Services
Standards purchased in soft copy format: Tel: +44 345 086 9001
Email (orders): orders@bsigroup.com
• A British Standard purchased in soft copy format is licensed to a sole named
user for personal or internal company use only. Email (enquiries): cservices@bsigroup.com

• The standard may be stored on more than 1 device provided that it is accessible Subscriptions
by the sole named user only and that only 1 copy is accessed at any one time. Tel: +44 345 086 9001
• A single paper copy may be printed for personal or internal company use only. Email: subscriptions@bsigroup.com

Standards purchased in hard copy format: Knowledge Centre

• A British Standard purchased in hard copy format is for personal or internal Tel: +44 20 8996 7004
company use only. Email: knowledgecentre@bsigroup.com
• It may not be further reproduced – in any format – to create an additional copy.
Copyright & Licensing
This includes scanning of the document.
Tel: +44 20 8996 7070
If you need more than 1 copy of the document, or if you wish to share the Email: copyright@bsigroup.com
document on an internal network, you can save money by choosing a subscription
product (see ‘Subscriptions’). BSI Group Headquarters
389 Chiswick High Road London W4 4AL UK