Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
366 views

APIC Controller Commands

This document provides commands for the APIC controller to view and manage various network elements including endpoints, VLANs, VPCs, interfaces, routing, and troubleshooting. Some key commands include acidiag fnvread to view fabric nodes, show endpoints vlan to display endpoints for a specific VLAN, and show tenant to view endpoints and EPG details within a tenant. Leaf commands cover viewing internal VLAN, endpoint, interface, routing, and overlay tunnel details. Spine commands allow viewing coop endpoint databases and dampened entries.

Uploaded by

ravi kant
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
366 views

APIC Controller Commands

This document provides commands for the APIC controller to view and manage various network elements including endpoints, VLANs, VPCs, interfaces, routing, and troubleshooting. Some key commands include acidiag fnvread to view fabric nodes, show endpoints vlan to display endpoints for a specific VLAN, and show tenant to view endpoints and EPG details within a tenant. Leaf commands cover viewing internal VLAN, endpoint, interface, routing, and overlay tunnel details. Spine commands allow viewing coop endpoint databases and dampened entries.

Uploaded by

ravi kant
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

APIC Controller commands

Misc/management
acidiag fnvread - display information about fabric nodes (leaves and spines).
fabric <NODE_ID> <COMMAND> - execute a COMMAND on NODE_ID. NODE_ID can be specified as range or list
of nodes, i.e. 101-103 or 101,105.
show oob - display information about Out-of-band management configuration.

Endpoints
show endpoints vlan xxx - display endpoints of specific VLAN xxx. Here xxx is exact encapsulation ID specified
in EPG interface deployment, not internal ID of leaves.
show tenant <TENANT> application <APP> epg - display list of EPGs inside TENANT / APP and their contracts
list.
show tenant <TENANT> application <APP> endpoints - list of endpoints for all EPGs inside TENANT / APP.
show tenant <TENANT> application <APP> epg <EPG> endpoints - list of endpoints for specific EPG inside
TENANT / APP.
show tenant <TENANT> endpoints vlan <ID> - list of endpoints for TENANT and specific encapsulation VLAN
ID.
show tenant <TENANT> application <APP> epg <EPG> details - display detailed information about EPG
inside TENANT / APP, including EPG configuration details, assigned domains, contracts, static paths.

PC/VPC
show vpc map - display VPC to interfaces mapping table which includes VPC name, VPC cluster ID, VPC ID, Leaf
ID/Name, port-channel interface ID, exact physical leaf interface.
show vpc map <VPC_IF_POLICY> - same as above, but only for specific VPC interface policy name.
show port-channel map
show port-channel map <VPC_IF_POLICY> - same as above, but little less info.

Bridge-domains
show tenant <TENANT> ip interface bridge-domain | egrep "Interface|<IP>" - find bridge-domain
name in TENANT with IP.

Interfaces
show stats granularity 15min leaf 103 interface ethernet 1/5 - show interface statistics for specified
interval.

Leaf commands

PC/VPC, VLANs
show vlan extended - display list of internal leaf VLAN ID mapping to EPG/BD and encap VLAN including leaf
interfaces.
show vpc extended - display list of VPC IDs mapping to internal Port-channel IDs, encap VLAN IDs, interface
policies.
vsh_lc -c "show system internal eltmc info vlan brief" - display table of internal VLANs. Access_enc
field represents the VLAN ID deployed to the interface (EPG/L3Out).
vsh_lc -c "show system internal eltmc info vlan <VLAN>" - display info for VLAN, where VLAN is the
ID of the internal VLAN. Internal VLAN ID numbers can be found with the help of show vlan extended command.

Endpoints
show system internal epm endpoint ip <IP> - display information about IP from dataplane.
clear system internal epm endpoint key vrf <TENANT>:<VRF> ip <IP> - clear learned endpoint in
TENANT / VRF with address IP.
show system internal epm vlan <ID> [detail] - display information about VLAN. In this command you
should pass internal VLAN ID, which could be obtained from show vlan extended command.
show ip arp internal event-history event - display ARP process traces.

Interfaces
cat /mit/sys/lldp/inst/if-[eth1--1]/summary - get information from MIT about leaf interface including its
MAC address, wiring issues, operational/admin status.
cat /mit/sys/summary - get leaf management information, state, sw version, uptime, last reboot reason, serial.
show interface snmp-ifindex - display SNMP interface indices, which are often appearing in various
logmessages.

Routing
show ip arp vlan xxx - display next-hop IP in ARP table (only for L3Out).
show ip route vrf TENANT:VRF_NAME [PREFIX] - display routes, PREFIX is optional.
show ip eigrp int bri vrf TENANT:VRF_NAME
show ip ospf int bri vrf TENANT:VRF_NAME - verify OSPF/EIGRP is enabled on a correct interface.
show ip eigrp neighbors vrf TENANT:VRF_NAME
show ip ospf neighbors vrf TENANT:VRF_NAME - check the status of neighbors.
show ip eigrp vrf TENANT:VRF_NAME | egrep 'AS|K' - display EIGRP AS, K values.
show ip bgp neighbors vrf TENANT:VRF_NAME | egrep 'BGP nei|Using|Opens|hops' - display BGP
neighbors info.
show ip bgp summary vrf TENANT:VRF_NAME - show BGP summary information.
show bgp sessions vrf overlay-1 - check if leaf have BGP sessions with RR spines.
show bgp vpnv4 unicast vrf overlay-1 - display redistributed/exported external routes in VRF overlay-1.

MCP/Spanning-tree

show mcp internal info vlan xxx - display MCP info about selected VLAN. In this case xxx is an encapsulation
VLAN ID on interface (not internal VLAN ID). With the help of this command you can also view the last TCN event
information.

Overlay
show isis dteps vrf overlay-1 - display Dynamic Tunnel Endpoints, existing in IS-IS.
show isis adjacency vrf overlay-1 - display IS-IS neighbor information for overlay-1.
Checks
iping -V <TENANT>:<VRF> <IP> - perform ping inside specific TENANT / VRF to IP. Complete list of options:
usage: iping
[ -d set the SO_DEBUG option]
[ -D enable debug information ]
[ -F enable do not fragment bit in IP header ]
[ -L receive packets on supplied interface ]
[ -n enable printing host IP address than resolved name ]
[ -q quiet output ]
[ -r disable routing of the packets, send only to directly connected hosts ]
[ -v output in verbose format ]
[ -V <vrf-name> name of the VRF through which destination is reachable ]
[ -c <count> no of packets to send ]
[ -i <wait> no of seconds to wait before sending next packet ]
[ -p <pattern> packet payload pattern ]
[ -s <packetsize> size of packets to send ]
[ -t <timeout> wait for seconds to receive reply ]
[ -S <source ip/interface> send packet with given source-ip or IP of given interface and
send packet out of that interface ]
<host> destination host-name or ip address

Spine commands

Endpoints
show coop internal info ip-db | grep <IP> -A 13 - display information about IP.
show coop internal info repo ep dampening - see the list of dampened EPs.

You might also like