Hydraulic Cylinder For Potentially Explosive Areas: Bosch Rexroth AG, RE 17335-X, Edition: 2019-04

Hydraulic cylinder for
potentially explosive areas
RE 17335-X
Edition: 2019-04
Series CDH2…XC / CGH2…XC / CSH2…XE Replaces: 11.16
▶▶ Series H2
▶▶ Component series 3X
▶▶ Nominal pressure 250 bar [25 MPa]
Features Contents
▶▶ Standards: DIN 24333, ISO 6022 Features1

▶▶ 6 types of mounting Ordering code series CDH2...XC 2, 3
▶▶ Piston Ø (ØAL): 40 … 320 mm Ordering code series CGH2...XC 4, 5
▶▶ Piston rod Ø (ØMM): 25 … 220 mm Ordering code series CSH2...XE 6, 7
▶▶ Stroke lengths up to 6 m Technical data 8 … 10
▶▶ Self-adjusting and adjustable end position cushioning Diameters, areas, forces, flow 11
Tolerances according to ISO 6020-1 11
Overview types of mounting series CDH2…XC 12
Overview types of mounting series CGH2…XC 12
Overview types of mounting series CSH2…XE 13
Dimensions CDH2…XC, CGH2…XC 14 … 25
Dimensions CSH2…XE 26 … 33
Flange ports 34, 35
Bleeding / measuring coupling, throttle valve 36
Position measurement system 37, 38
Equipotential bonding 39, 40
Mounting elements 41, 42
Kinking, admissible stroke length 43 … 45
End position cushioning 46 … 48
Selection criteria for seals 49
Seal kits 50 … 53
Tightening torques 54
Spare parts drawing 55 … 57
Cylinder weight 58
Bosch Rexroth AG, RE 17335-X, edition: 2019-04

2/60 CDH2…XC / CGH2…XC / CSH2…XE | Hydraulic cylinder for potentially explosive areas
Ordering code: Series CDH2…XC
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CD H2 / / / XC 3X /
01 Differential cylinder CD
02 Series H2
Types of mounting
03 Swivel eye at base MP3
Self-aligning clevis at base MP5
Round flange at head MF3
Round flange at base MF4
Trunnion MT4 2)
Foot mounting MS2 18)
04 Piston Ø (ØAL) 40 ... 320 mm ...
05 Piston rod Ø (ØMM) 25 ... 220 mm ...
06 Stroke length in mm 3) ...
Protection class for ATEX version

07 Design safety XC
08 Component series 30 … 39 (30 … 39: unchanged installation and connection dimensions) 3X
Line connection / version

09 According to ISO 1179-1 (pipe thread ISO 228-1) B
According to ISO 9974-1 (metric thread ISO 261) M 33)
Flange connection according to ISO 6162-1 tab. 2 type 1 (≙ SAE 3000 PSI) F 4; 21)
Flange connection according to ISO 6162-2 tab. 2 type 1 (≙ SAE 6000 PSI) D 4; 9)
Flange connection according to ISO 6164 tab. 1 K 1; 4)
Flange connection according to ISO 6164 tab. 2 H 4)
Line connection / position at head

10 View to piston rod 30)
1
2

3
4
Line connection / position at base

1
2

3
4
Piston rod design

12 Hard chromium-plated C
Hardened and hard chromium-plated H 23)
Nickel-plated and hard chromium-plated N 24)
Piston rod end

13 Thread for swivel head CGKD H
With mounted swivel head CGKD F

Hydraulic cylinder for potentially explosive areas | CDH2…XC / CGH2…XC / CSH2…XE 3/60
Ordering code: Series CDH2…XC
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CD H2 / / / XC 3X /
End position cushioning

14 Without end position cushioning U
Both sides, self-adjusting D 1)
Both sides, adjustable E
Seal design
15 For mineral oil HL, HLP and oil-in-water-emulsion HFA Standard seal system M
For mineral oil HL, HLP, oil-in-water emulsion HFA and Servo quality / reduced friction T
water glycol HFC Chevron seal kits A
For phosphoric acid esters HFDR Servo quality / reduced friction S
Chevron seal kits B
Option
16 Additional options, fill fields for additional options Z
Without additional options, do not fill fields for additional options W
Additional options
Fields for additional options

17 18 19 20 21
Z W
17 Without option W
18 Additional guide rings F 10)
Without additional guide rings W
19 Measuring coupling, on both sides A

Without measuring coupling W
20 Flanged grease nipple B

Standard conical grease nipple W
21 Specify the piston rod extension LY in the plain text in mm Y

Without piston rod extension W
Order examples:
Without additional options: With additional options:

CDH2MT4/63/45/350XC3X/B11CHDMWW, XV=300 mm CDH2MF3/80/56/500XC3X/B11CHDMZ WWAWW
1) Only piston Ø 40 to 200 mm 18) Not standardized

2) Trunnion position freely selectable. 21) Only piston Ø 63 to 200 mm
When ordering, always specify the "XV" dimensions in the 23) Only piston rod Ø 25 to 140 mm
plain text in mm 24) Only piston rod Ø 40 to 160 mm
3) Observe the max. available stroke length, page 11, and the 30) All graphical presentations in the data sheet show position 1
admissible stroke length (acc. to kinking calculation) 33) Version does not comply with ISO 6022
on pages 43 to 45
4) Not possible with MF4
9) Only piston Ø 80 to 320 mm
10) Seal designs A, B not possible;
Piston Ø 220 to 320 mm standard
RE 17335-X, edition: 2019-04, Bosch Rexroth AG

Ordering code: Series CGH2…XC
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CG H2 / / / XC 3X /
01 Double-acting cylinders CG
02 Series H2
Types of mounting
03 Round flange at head MF3
Trunnion MT4 2)
Foot mounting MS2
04 Piston Ø (ØAL) 40 ... 320 mm ...

07 Design safety XC

Flange connection according to ISO 6162-1 tab. 2 type 1 (≙ SAE 3000 PSI) F 21)
Flange connection according to ISO 6162-2 tab. 2 type 1 (≙ SAE 6000 PSI) D 9)
Flange connection according to ISO 6164 tab. 1 K 1)
Flange connection according to ISO 6164 tab. 2 H

1
2

3
4

1
2

3
4
Piston rod design

Piston rod end

With mounted swivel head CGKD F 17)

Both sides, self-adjusting D 1)
Both sides, adjustable E

Ordering code: Series CGH2…XC
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CG H2 / / / XC 3X /
Seal design
15 For mineral oil HL, HLP and oil-in-water-emulsion HFA Standard seal system M
For mineral oil HL, HLP, oil-in-water emulsion HFA and Servo quality / reduced friction T
water glycol HFC Chevron seal kits A
For phosphoric acid esters HFDR Servo quality / reduced friction S
Chevron seal kits B
Option
Without additional options, do not fill fields for additional options W
Additional options

17 18 19 20 21
Z W
17 Without option W
18 Additional guide rings F 10)
Without additional guide rings W


21 Specify the piston rod extension LY in the plain text in mm Y 16)
Order examples:
Without additional options: With additional options:

CGH2MF3/100/70/500XC3X/B11CHUMWW CGH2MF3/100/70/500XC3X/B11CHUMZ WWAWW
1) Only piston Ø 40 to 200 mm 18) Not standardized

When ordering, always specify the "XV" dimensions in the 23) Only piston rod Ø 25 to 140 mm
plain text in mm 30) All graphical presentations in the data sheet show position 1
3) Observe the max. available stroke length, page 11, and the 33) Version does not comply with ISO 6022
admissible stroke length (acc. to kinking calculation)
on pages 43 to 45
10) Seal designs A, B not possible;
Piston Ø 220 to 320 mm standard
16) Only at left piston rod side
(orientation: catalog figures)
17) Only one swivel head / plain clevis mounted, left piston rod side
(orientation: catalog figures)

Ordering code: Series CSH2…XE
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CS H2 / / / XE 3X / Z
01 Differential cylinder with position measurement system CS 18)
02 Series H2
Types of mounting
03 Swivel eye at base MP3 34)
Self-aligning clevis at base MP5 34)
Round flange at head MF3

Round flange at base MF4
Trunnion MT4 2)
Foot mounting MS2
04 Piston Ø (ØAL) 40 ... 320 mm ...

07 Increased safety XE

Flange connection according to ISO 6162-1 tab. 2 type 1 (≙ SAE 3000 PSI) F 4; 21)
Flange connection according to ISO 6162-2 tab. 2 type 1 (≙ SAE 6000 PSI) D 4; 9)
Flange connection according to ISO 6164 tab. 1 K 1; 4)
Flange connection according to ISO 6164 tab. 2 H 4)

1
2

3
4

1
2

3
4
Piston rod design

Piston rod end

With mounted swivel head CGKD F

Ordering code: Series CSH2…XE
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
CS H2 / / / XE 3X / Z

Both sides, adjustable E 20)
Seal design
15 For mineral oil HL, HLP and oil-in-water-emulsion HFA Standard seal system M 29)
For mineral oil HL, HLP, oil-in-water emulsion HFA and

Servo quality / reduced friction T 29)
water glycol HFC
For phosphoric acid esters HFDR Servo quality / reduced friction S 29)
Option
Additional options

17 18 19 20 21
Z T
17 Position measurement system (magnetostrictive) without mating connector, mating connector ‒ separate order, T
see page 37
18 Analog output 4 ... 20 mA C

Analog output 0 ... 10 V F
Digital output SSI D


21 Specify the piston rod extension LY in the plain text in mm Y

Order example:
CSH2MF3/100/70/500XE3X/B11CHUTZ TFABW
1) Only piston Ø 40 to 200 mm 20) Possible from piston rod Ø 45 mm

When ordering, always specify the "XV" dimensions in the 29) With CSH2…XE, by default with guide belts
plain text in mm 30) All graphical presentations in the data sheet show position 1
3) Observe the max. available stroke length, page 11, and the 33) Version does not comply with ISO 6022
admissible stroke length (acc. to kinking calculation) on 34) Only upon request
pages 43 to 45
4) Not possible with MF4
18) Not standardized
19) Only piston rod Ø 28 mm to 140 mm

Technical data
(For applications outside these values, please consult us!)
ATEX units for potentially explosive areas

What you need to know about the documentation for Information on explosion protection:
ATEX units. ▶▶ Cylinders without position measurement system
The documentation for ATEX units applies to the –– Marking according to directive
explosion-proof version of Bosch Rexroth hydraulic 2014/34/EU II 2G Ex h IIC T4 Gb
cylinders and consists of the following parts: –– Marking according to directive
▶▶ Operating instructions 07100-B for tie rod design / mill 2014/34/EU II 2D Ex h IIIC T135 °C Db
type hydraulic cylinders and mill type for potentially –– Ambient temperature –20 °C ≤ Ta ≤ +80 °C
explosive areas ▶▶ Cylinders with position measurement system
▶▶ Technical data sheet 17335-X –– Marking according to directive
▶▶ Operating instructions of the position measurement 2014/34/EU II 3G Ex ec IIC T4 Gc
system (only with version CSH2..XE) –– Marking according to directive
▶▶ Declaration of conformity according to directive 2014/34/EU II 3D Ex tc IIIC T135 °C Dc
2014/34/EU –– Ambient temperature –20 °C ≤ Ta ≤ +75 °C
You can find further information on the correct handling
of hydraulic products in our publication "General product
information on hydraulic products" 07008.
General
Weight kg see page 58
Installation position any
Ambient temperature range °C see page 49
Primer coat 1) μm min. 40
Hydraulic
Nominal pressure 2) bar [MPa] 250 [25]
Minimum operating pressure 3) (without load) bar [MPa] 10 [1]
Static test pressure bar [MPa] 375 [37.5]
Reduced test pressure bar [MPa] 315 [31.5]
Hydraulic fluid see table below
Hydraulic fluid temperature range °C see page 49
Viscosity range mm2/s 12 … 380
Maximum admissible degree of contamination of the Class 20/18/15 4)
hydraulic fluid cleanliness class according to ISO 4406 (c)

Stroke speed 5) (depending on line connection) m/s see table page 9
Bleeding by default secured against screwing out
Hydraulic fluid 6) Classification Suitable sealing materials Standards

Mineral oils HL, HLP NBR, FKM DIN 51524
Oil-in-water emulsion HFA NBR, FKM ISO 12922
Phosphoric acid esters HFDR FKM ISO 12922
Water glycol HFC upon request
Important information on hydraulic fluids: temperature class.

▶▶ The ignition temperature of the hydraulic fluid used must be 50 K ▶▶ In order to prevent electrostatic charging, the hydraulic fluid must
higher than the maximum surface temperature of the set have a conductivity > 10000 pS/m.

Technical data
Stroke velocity
Piston Ø Max. stroke velocity Piston Ø Max. stroke velocity
Line connection Line connection
in mm in m/s in mm in m/s
40 G1/2 0.31 160 G1 1/4 0.12
50 G1/2 0.20 180 G1 1/4 0.10
63 G3/4 0.28 200 G1 1/4 0.08
80 G3/4 0.18 220 G1 1/2 0.09
100 G1 0.20 250 G1 1/2 0.07
125 G1 0.13 280 G1 1/2 0.06
140 G1 1/4 0.16 320 G1 1/2 0.04
1) By default, hydraulic cylinders are primed with a coating 4) The cleanliness classes specified for the components must
(color gentian blue RAL 5010). Other colors upon request. With be adhered to in hydraulic systems. Effective filtration prevents
cylinders and attachment parts, the following surfaces are not faults and simultaneously increases the life cycle of the
primed or painted: components.
▶▶ All fit diameters to the customer side For the selection of filters, see www.boschrexroth.com/filter.
▶▶ Sealing surfaces for line connection 5) Please observe the guideline on max. stroke velocities
▶▶ Sealing surfaces for flange connection (with recommended flow velocity of 5 m/s in the line connection)
▶▶ Position measurement system in the table. Higher stroke velocity upon request.
The areas that are not painted are protected by means If the extension velocity is considerably higher than the retraction
of a solvent-free corrosion protection agent. velocity of the piston rod, drag-out losses of the medium
2) Higher operating pressures upon request may result. If necessary, please consult us.
The specified operating pressures apply to applications with 6) For further information on hydraulic fluids refer
shock-free operation with regard to excess pressure to data sheet R.90223.
and / or external loads. With extreme loads like e.g. high cycle
sequence, mounting elements and threaded piston rod
connections must be designed for durability.
3) Depending on the application, a certain minimum pressure
is required in order to guarantee good functioning of the cylinder.
Without load, a minimum pressure of 10 bar is recommended for
differential cylinders; for lower pressures as well as double-acting
cylinders, please contact us.

Technical data
Notice! Standards:
Boundary and application conditions: The installation dimensions and types of mounting of the
▶▶ The mechanical alignment of the movement axis and cylinder comply with the standards DIN 24333 and
thus the mounting points of hydraulic cylinder and ISO 6022.
piston rod must be ensured. Lateral forces on the Acceptance:
guides of piston rod and piston are to be avoided. Each cylinder is tested according to Bosch Rexroth
It may be necessary to consider the own weight of the standard and in compliance with ISO 10100: 2001.
hydraulic cylinder (MP3 / MP5 or MT4) or the Safety instructions:
piston rod. For assembly, commissioning and maintenance
▶▶ The bending length / bending load of the piston rod of hydraulic cylinders, observe the operating
and / or the hydraulic cylinder must be observed instructions 07100-B!
(see page 43). Service and repair work has to be performed
▶▶ The maximum admissible stroke velocities with regard by Bosch Rexroth AG or by personnel especially trained
to the suitability / load of seals must be observed for this purpose. No warranty is accepted for damage
as must their compatibility with the properties of the as a consequence of assembly, maintenance or repair
hydraulic fluid (see page 49). work not performed by Bosch Rexroth AG.
▶▶ The maximum admissible velocities / kinetic energies Check lists for hydraulic cylinders:
when moving into the end positions, also considering Cylinders the characteristics and/or application
external loads, must be observed. parameters of which deviate from the values specified
Danger: Excess pressure in the data sheet can only be offered as a special version
▶▶ The maximum admissible operating pressure must upon request. For offers, the deviations of the
be complied with in any operating state of the characteristics and / or application parameters must
hydraulic cylinder. be described in the check lists for
Possible pressure intensification resulting from the hydraulic cylinders (07200).
area ratio of annulus area to piston area and possible
throttling points are to be observed. This list does not claim to be complete. In case
▶▶ Detrimental environmental influences, e.g. aggressive of questions regarding the compatibility with media
finest particles, vapors, high temperatures, etc. or exceedance of the boundary or application
as well as contaminations and deterioration of the conditions, please contact us.
hydraulic fluid are to be avoided.
▶▶ Minimum stroke: All graphical representations in the data sheet are
When using end position cushioning, the minimum examples. The product supplied may therefore differ
stroke must also be observed, see page 46 to 48 from the figure.
"End position cushioning".

Diameters, areas, forces, flow
Piston Piston Area ratio Areas Force at 250 bar 1) Flow at 0.1 m/s 2) Max.
rod Piston Rod Ring Pressure Diff. Pulling Off Diff. On available
stroke length
ØAL ØMM ϕ A1 A2 A3 F1 F2 F3 qV1 qV2 qV3
mm mm A1/A3 cm2 cm2 cm2 kN kN kN l/min l/min l/min mm
25 1.64 4.90 7.65 12.25 19.12 2.9 4.6
40 12.56 31.40 7.5 2000
28 1.96 6.16 6.40 15.40 16.00 3.7 3.8
32 1.69 8.04 11.59 20.12 28.98 4.8 7.0
50 19.63 49.10 11.8 2000
36 2.08 10.18 9.45 25.45 23.65 6.1 5.7
40 1.67 12.56 18.61 31.38 46.52 7.5 11.2
63 31.17 77.90 18.7 2000
45 2.04 15.90 15.27 39.75 38.15 9.5 9.2
50 1.66 19.63 30.63 49.07 76.58 11.8 18,4
80 50.26 125.65 30.2 2000
56 1.96 24.63 25.63 61.55 64.10 14.8 15.4
63 1.66 31.16 47.38 77.93 118.42 18.7 28.4
100 78.54 196.35 47.1 3000
70 1.96 38.48 40.06 96.20 100.15 23.1 24.0
80 1.69 50.24 72.48 125.62 181.13 30.1 43.5
125 122.72 306.75 73.6 3000
90 2.08 63.62 59.10 159.05 147.70 38.2 35.4
90 1.70 63.62 90.32 159.05 225.70 38.2 54.2
140 153.94 384.75 92.4 3000
100 2.04 78.54 75.40 196.35 188.40 47.1 45.3
100 1.64 78.54 122.50 196.35 306.15 47.1 73.5
160 201.06 502.50 120.6 3000
110 1.90 95.06 106.00 237.65 264.85 57.0 63.6
110 1.60 95.06 159.43 237.65 398.52 57.0 95.7
180 254.47 636.17 152.7 3000
125 1.93 122.72 131.75 306.80 329.37 73.6 79.1
125 1.64 122.72 191.44 306.80 478.45 73.6 114.9
200 314.16 785.25 188.5 3000
140 1.96 153.96 160.20 384.90 400.35 92.4 96.1
140 1.68 153.96 226.2 384.9 565.5 92.4 135.7
220 380.1 950.3 228.1 6000
160 2.12 201.0 179.1 502.6 447.7 120.7 107.4
160 1.69 201.0 289.8 502.6 724.5 120.7 173.8
250 490.8 1227.2 294.5 6000
180 2.08 254.4 236.4 636.2 590.0 152.7 141.8
180 1.70 254.4 361.3 636.2 903.2 152.7 216.7
280 615.7 1539.4 369.4 6000
200 2.04 314.1 301.6 785.4 753.9 188.5 180.9
200 1.64 314.1 490.1 785.4 1225.2 188.5 294.0
320 804.2 2010.6 482.5 6000
220 1.90 380.1 424.2 950.3 1060.3 228.1 254.4

1) Theoretical static cylinder force 2) Stroke velocity

(without consideration of the efficiency and admissible load for
attachment parts such as swivel heads, plates, or valves, etc.)
Tolerances according to ISO 6020-1
Installation dimensions WC XC 2) XO 2) XS 1,; 2) XV 2) ZP 2)
Type of mounting MF3 MP3 MP5 MS2 MT4 MF4 Stroke tolerances
Stroke length Tolerances
≤ 1250 ±2 ±1.5 ±1.5 ±2 ±2 ±1.5 +2
> 1250 – ≤ 3150 ±4 ±3 ±3 ±4 ±4 ±3 +5
> 3150 – ≤ 6000 ±8 ±5 ±5 ±8 ±8 ±5 +8
1) Not standardized 2) Including stroke length

Overview types of mounting: Series CDH2…XC
CDH2…XC: MP3 CDH2…XC: MF4

see page 14, 15 see page 20, 21
CDH2…XC: MP5 CDH2…XC: MT4

CDH2…XC: MF3 CDH2…XC: MS2

Overview types of mounting: Series CGH2…XC
CGH2…XC: MF3 CGH2…XC: MS2

CGH2…XC: MT4
see page 22, 23

Overview types of mounting: Series CSH2…XE
CSH2…XE: MF3 CSH2…XE: MT4

CSH2…XE: MF4 CSH2…XE: MS2


Dimensions: Swivel eye at base CDH2...XC: MP3

(dimensions in mm)
CDH2...XC: MP3
16) Y PJ + X* 16)
¯D42) ¯D42) 10)

NV 16)
EE EE
VE "A"
G 1/41)
MR
X1
X1
¯MM
¯RA
¯DA
KK
¯D
5)
"A"
WA L1
L
A XC + X* M1
"A-A"
¯CD11)
EW
CDH2...XC: MP3: with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Swivel eye at base CDH2...XC: MP3

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA XC

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18 282

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18 305
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 348
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 395
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 442
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 520
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 580
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 617
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 690
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 756
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 890
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 903
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 1072
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 1080
ØAL ØMM L L1 MR M1 ØCD EW ØRA VE ØRA VE

H9 h12 7) 7) 8) 8)
40 6) 25/28 53 8 32 32 25 25 52 29 88 –
50 32/36 61 8 40 40 32 32 63 29 102 –
63 40/45 74 8 50 50 40 40 75 32 120 –
80 50/56 90 10 63 63 50 50 90 36 145 –
100 63/70 102 12 71 71 63 63 110 41 170 –
125 80/90 124 16 90 90 80 80 132 45 206 –
140 90/100 149 16 100 100 90 90 145 45 226 –
160 100/110 150 16 112 112 100 100 160 50 200 50
180 110/125 180 20 129 129 110 110 185 55 220 55
200 125/140 206 20 145 145 125 125 200 61 235 61
220 6) 140/160 253 20 179 12) 187 12) 160 160 235 71 270 71
250 160/180 253 24 179 12) 187 12) 160 160 250 71 300 71
280 6) 180/200 320 30 230 12) 240 12) 200 200 295 88 325 88
320 200/220 320 30 231 12) 241 12) 200 200 320 88 365 88
ØAL = Piston Ø 6) Piston Ø not standardized

ØMM = Piston rod Ø 7) Dimensions for cylinders with seal design M, T, and S
X* = Stroke length 8) Dimensions for cylinders with seal design A and B
1) Bleeding: With view to the piston rod, the position is offset 10) Standard version "W"
by 90° in relation to the line connection (clockwise) Lubricating nipple, cone head form A according to DIN 71412
2) Ø D4 max. 0.5 mm deep 11) Related bolt Ø f8
3) Thread size does not comply with ISO 6022; 12) The specified dimensions are maximum values, tolerance
M50 x 2 available upon request classes 342 according to ISO 9013 Thermal cutting
4) Flange connections see separate tables on pages 34 and 35 16) Equipotential bonding see pages 40 and 41
5) Throttle valve only with end position cushioning "E" 19) Line connection "B"
(180° for bleeding) 20) Line connection "M"

Dimensions: Self-aligning clevis at base CDH2...XC: MP5

(dimensions in mm)
CDH2...XC: MP5

CDH2...XC: MP5: with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Self-aligning clevis at base CDH2...XC: MP5

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA XO

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18 282

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18 305
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 348
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 395
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 442
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 520
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 580
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 617
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 690
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 756
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 890
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 903
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 1072
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 1080
ØAL ØMM LT L1 MS M1 ØCX 11) EP EX ØRA VE ØRA VE Z

H7 h12 7) 7) 8) 8)
40 6) 25/28 53 8 32 32 25 22 25 52 29 88 – 2°
50 32/36 61 8 40 40 32 27 32 63 29 102 – 4°
63 40/45 74 8 50 50 40 32 40 75 32 120 – 4°
80 50/56 90 10 63 63 50 40 50 90 36 145 – 4°
100 63/70 102 12 71 71 63 52 63 110 41 170 – 4°
125 80/90 124 16 90 90 80 66 80 132 45 206 – 4°
140 90/100 149 16 100 100 90 72 90 145 45 226 – 4°
160 100/110 150 16 112 112 100 84 100 160 50 200 50 4°
180 110/125 180 20 129 129 110 88 110 185 55 220 55 4°
200 125/140 206 20 145 145 125 102 125 200 61 235 61 4°
220 6) 140/160 253 20 179 12) 187 12) 160 130 160 235 71 270 71 4°
250 160/180 253 24 179 12) 187 12) 160 130 160 250 71 300 71 4°
280 6) 180/200 320 30 230 12) 240 12) 200 138 200 295 88 325 88 4°
320 200/220 320 30 231 12) 241 12) 200 162 200 320 88 365 88 4°

ØMM = Piston rod Ø 7) Dimensions for cylinders with seal design M, T, and S
X* = Stroke length 8) Dimensions for cylinders with seal design A and B
1) Bleeding: With view to the piston rod, the position is offset 10) Standard version "W"
by 90° in relation to the line connection (clockwise) Lubricating nipple, cone head form A according to DIN 71412
2) Ø D4 max. 0.5 mm deep 11) Related bolt Ø f8
4) Flange connections see separate tables on pages 34 and 35 16) Equipotential bonding see pages 40 and 41
5) Throttle valve only with end position cushioning "E" 19) Line connection "B"

Dimensions: Round flange at head CDH2...XC / CGH2...XC: MF3

(dimensions in mm)
CDH2...XC: MF3

CGH2...XC: MF3 10)

CGH2...XC: MF3 10): with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Round flange at head CDH2...XC / CGH2...XC: MF3

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48
ØAL ØMM ØRD WC VD NF PK ZB ZM ØFB ØFC ØUC ØRA VE ØRA VE

f8 js13 max. H13 js13 ‒1 7) 7) 8) 8)
40 6) 25/28 52 22 4 25 120 230 286 11 115 138 52 29 88 –

50 32/36 63 22 4 25 120 244 316 13.5 132 155 63 29 102 –
63 40/45 75 25 4 28 133 274 357 13.5 150 175 75 32 120 –
80 50/56 90 28 4 32 155 305 395 17.5 180 210 90 36 145 –
100 63/70 110 32 5 36 171 340 439 22 212 250 110 41 170 –
125 80/90 132 36 5 40 205 396 511 22 250 290 132 45 206 –
140 90/100 145 36 5 40 219 430 551 26 285 330 145 45 226 –
160 100/110 160 40 5 45 235 467 605 26 315 360 160 50 200 50
180 110/125 185 45 5 50 264 510 652 33 355 410 185 55 220 55
200 125/140 200 45 5 56 278 550 718 33 385 440 200 61 235 61
220 6) 140/160 235 50 8 63 326 637 814 39 435 500 235 71 270 71
250 160/180 250 50 8 63 326 650 840 39 475 540 250 71 300 71
280 6) 180/200 295 56 8 80 375 752 955 45 555 630 295 88 325 88
320 200/220 320 56 8 80 391 760 955 45 600 675 320 88 365 88
ØAL = Piston Ø 5) Throttle valve only with end position cushioning "E"
ØMM = Piston rod Ø (180° for bleeding)
6) Piston Ø not standardized
X* = Stroke length
7) Dimensions for cylinders with seal design M, T, and S
1) Bleeding: With view to the piston rod, the position is offset
by 90° in relation to the line connection (clockwise) 8) Dimensions for cylinders with seal design A and B
2) Ø D4 max. 0.5 mm deep 10) Double-acting cylinder not standardized
3) Thread size does not comply with ISO 6022; 16) Equipotential bonding see pages 40 and 41
M50 x 2 available upon request 19) Line connection "B"
4) Flange connections see separate tables on pages 34 and 35 20) Line connection "M"

Dimensions: Round flange at base CDH2...XC: MF4

(dimensions in mm)
CDH2...XC: MF4

CDH2...XC: MF4 10): with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Round flange at base CDH2...XC: MF4

(dimensions in mm)

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48
ØAL ØMM ZP NF VA ØBA ØFB ØFC ØUC ØRA VE ØRA VE

js13 H8 H13 js13 ‒1 7) 7) 8) 8)
40 6) 25/28 250 25 5 52 11 115 138 52 29 88 –

50 32/36 265 25 4 63 13.5 132 155 63 29 102 –
63 40/45 298 28 4 75 13.5 150 175 75 32 120 –
80 50/56 332 32 5 90 17.5 180 210 90 36 145 –
100 63/70 371 36 5 110 22 212 250 110 41 170 –
125 80/90 430 40 6 132 22 250 290 132 45 206 –
140 90/100 465 40 5 145 26 285 330 145 45 226 –
160 100/110 505 45 7 160 26 315 360 160 50 200 50
180 110/125 550 50 10 185 33 355 410 185 55 220 55
200 125/140 596 56 10 200 33 385 440 200 61 235 61
220 6) 140/160 690 63 10 235 39 435 500 235 71 270 71
250 160/180 703 63 10 250 39 475 540 250 71 300 71
280 6) 180/200 822 80 10 295 45 555 630 295 88 325 88
320 200/220 830 80 10 320 45 600 675 320 88 365 88
ØAL = Piston Ø 4) Flange connections see separate tables on pages 34 and 35

ØMM = Piston rod Ø 5) Throttle valve only with end position cushioning "E"
X* = Stroke length (180° for bleeding)
by 90° in relation to the line connection (clockwise) 7) Dimensions for cylinders with seal design M, T, and S
2) Ø D4 max. 0.5 mm deep 8) Dimensions for cylinders with seal design A and B
3) Thread size does not comply with ISO 6022; 16) Equipotential bonding see pages 40 and 41
M50 x 2 available upon request 19) Line connection "B"
20) Line connection "M"

Dimensions: Trunnion CDH2...XC / CGH2...XC: MT4

(dimensions in mm)
CDH2...XC: MT4

Dimensions for cylinder with

CDH2...XC: MT4: with seal design "A", "B" and AL Ø 160 ... 320 mm piston rod extension "LY"
in retracted condition

CGH2...XC: MT4 11)

CGH2...XC: MT4 11): with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Trunnion CDH2...XC / CGH2...XC: MT4

(dimensions in mm)

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40
220 6) 140/160 M125x4 125 120/140 355 273 65 G1 1/2 M48x2 3) 244 326 174 42
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48
ØAL ØMM PK ZB ZM X* XV 14) XV 12) XV 12) BD UV ØTD TL TM r ØRA VE ØRA VE

max. min. average min. max. 15) f8 js16 h12 7) 7) 8) 8)
40 6) 25/28 120 230 286 22 143+X*/2 154 140+X* 38 97 25 20 95 0.8 52 29 88 –

50 32/36 120 244 316 32 158+X*/2 174 151+X* 38 111 32 25 112 0.8 63 29 102 –
63 40/45 133 274 357 47 178.5+X*/2 202 167+X* 48 129 40 32 125 1 75 32 120 –
80 50/56 155 305 395 58 197.5+X*/2 226.5 180.5+X* 58 163 50 40 150 1 90 36 145 –
100 63/70 171 340 439 79 219.5+X*/2 259 195+X* 78 188 63 50 180 1.2 110 41 170 –
125 80/90 205 396 511 91 255.5+X*/2 301 210+X* 98 234 80 63 224 1.2 132 45 206 –
140 90/100 219 430 551 121 275.5+X*/2 336 215+X* 118 257 90 70 265 1.5 145 45 226 –
160 100/110 235 467 605 142 302.5+X*/2 373.5 231.5+X* 128 287 100 80 280 1.5 160 50 200 50
180 110/125 264 510 652 158 326+X*/2 405 247+X* 138 328 110 90 320 1.5 185 55 220 55
200 125/140 278 550 718 204 359+X*/2 461 257+X* 178 343 125 100 335 1.5 200 61 235 61
220 6) 140/160 326 637 814 200 407+X*/2 507 307+X* 180 393 160 125 385 1.5 235 71 270 71
250 160/180 326 650 840 210 420+X*/2 525 315+X* 180 433 160 125 425 1.5 250 71 300 71
280 6) 180/200 375 752 955 241 477.5+X*/2 598 357+X* 220 486 200 160 480 2 295 88 325 88
320 200/220 391 760 955 245 477.5+X*/2 600 355+X* 220 536 200 160 530 2 320 88 365 88
ØAL = Piston Ø Preferred XV dimension: Observe trunnion position in cylinder

ØMM = Piston rod Ø center XVmin. and XVmax.
14) XV
X* = Stroke length cent. recommendation: Trunnion position in cylinder center
15) The specified dimensions are maximum values, tolerance
X*min. = min. stroke length
1) Bleeding: With view to the piston rod, the position is offset classes 342 according to ISO 9013 Thermal cutting
16) Equipotential bonding see pages 40 and 41
by 90° in relation to the line connection (clockwise)
2) 17) Trunnion nut with AL Ø ≥ 125 mm either at head or at base side
Ø D4 max. 0.5 mm deep
3) Thread size does not comply with ISO 6022; depending on the position of the trunnion (XV).
19) Line connection "B"
M50 x 2 available upon request
4) 20) Line connection "M"
Flange connections see separate tables on pages 34 and 35
5) Throttle valve only with end position cushioning "E"
(180° for bleeding)
6) Piston Ø not standardized Important installation information!
7) Dimensions for cylinders with seal design M, T, and S
8)
During installation, it must be ensured that the trunnion
Dimensions for cylinders with seal design A and B
10) Observe the min. stroke length "X*
min."
bearings are installed up to the trunnion shoulders. Any
11) Double-acting cylinder not standardized non-compliance may reduce the product's service life.
12) When ordering, always specify the "XV" dimension in the clear
text.
Dimensions: Foot mounting CDH2...XC / CGH2...XC: MS2

(dimensions in mm)
CDH2...XC: MS2 2; 11)

CDH2...XC: MS2 11): with seal design "A", "B" and AL Ø 160 ... 320 mm

CGH2...XC: MS2 11)

CGH2...XC: MS2 11): with seal design "A", "B" and AL Ø 160 ... 320 mm


Dimensions: Foot mounting CDH2...XC / CGH2...XC: MS2

(dimensions in mm)

2) 4), 19) 4), 20)
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18

50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48
ØAL ØMM PK XS ZB ZM SS X* S S1 ØSB ST TS US LH L1 ØRA VE ØRA VE

max. min. H13 js13 15) 7) 7) 8) 8)
40 6) 25/28 120 118 230 286 50 1 30 15 11 32 110 140 45 93 52 29 88 –

50 32/36 120 135.5 244 316 45 1 35 17.5 11 37 130 161 55 110 63 29 102 –
63 40/45 133 154 274 357 49 1 40 20 13.5 42 150 183 65 129 75 32 120 –
80 50/56 155 171.5 305 395 52 2 50 25 17.5 47 180 220 75 149 90 36 145 –
100 63/70 171 189 340 439 61 3 60 30 22 57 210 260 90 181 110 41 170 –
125 80/90 205 218 396 511 75 1 70 35 26 67 255 313 105 215 132 45 206 –
140 90/100 219 240.5 430 551 70 19 85 42.5 30 72 290 359 115 235 145 45 226 –
160 100/110 235 270 467 605 65 44 105 52.5 33 77 330 402 135 277 160 50 200 50
180 110/125 264 291.5 510 652 69 50 115 57.5 40 92 360 445 150 305 185 55 220 55
200 125/140 278 322.5 550 718 73 56 125 62.5 40 97 385 471 160 322 200 61 235 61
220 6) 140/160 326 369.5 637 814 75 100 155 77.5 45 102 445 541 185 373 235 71 270 71
250 160/180 326 382.5 650 840 75 100 155 77.5 52 112 500 610 205 414 250 71 300 71
280 6) 180/200 375 415.5 752 955 124 51 155 77.5 52 142 550 661 235 469 295 88 325 88
320 200/220 391 435 760 955 85 125 190 95 62 142 610 732 255 512 320 88 365 88
ØAL = Piston Ø 7) Dimensions for cylinders with seal design M, T, and S

ØMM = Piston rod Ø 8) Dimensions for cylinders with seal design A and B
X* = Stroke length 10) Observe the min. stroke length "X*min."
X*min. = min. stroke length 11) Not standardized
1) Bleeding: With view to the piston rod, the position is offset 12) Recess 2 mm deep, for hexagon socket head cap screws;
by 90° in relation to the line connection (clockwise) ISO 4762 – The screws must not be subjected to shear force.
2) Ø D4 max. 0.5 mm deep Force introduction via additional external fitting strip
4) 16) Equipotential bonding see pages 40 and 41
Flange connections see separate tables on pages 34 and 35
5) 19) Line connection "B"
Throttle valve only with end position cushioning "E"

Dimensions: Round flange at head CSH2...XE: MF3

(dimensions in mm)
CSH2...XE: MF3


Dimensions: Round flange at head CSH2...XE: MF3

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 X* L5 D1

2) 4), 19) 4), 20) max. max.
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 1000 166 80
50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 1000 166 96
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 2000 166 96
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 2000 166 96
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 3000 166 96
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 3000 166 96
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 3000 166 96
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 3000 166 96
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 3000 166 96
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 3000 166 96
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 3000 166 96
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 3000 166 96
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 3000 166 96
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 3000 166 96
ØAL ØMM ØRD WC VD NF ZB ØFB ØFC ØUC

f8 js13 max. H13 js13 ‒1
40 6) 25/28 52 22 4 25 239 11 115 138
50 32/36 63 22 4 25 254 13.5 132 155
63 40/45 75 25 4 28 299 13.5 150 175
80 50/56 90 28 4 32 332.5 17.5 180 210
100 63/70 110 32 5 36 362 22 212 250
125 80/90 132 36 5 40 410 22 250 290
140 90/100 145 36 5 40 440 26 285 330
160 100/110 160 40 5 45 472.5 26 315 360
180 110/125 185 45 5 50 510 33 355 410
200 125/140 200 45 5 56 550 33 385 440
220 6) 140/160 235 50 8 63 637 39 435 500
250 160/180 250 50 8 63 650 39 475 540
280 6) 180/200 295 56 8 80 752 45 555 630
320 200/220 320 56 8 80 760 45 600 675

X*max. = max. stroke length
by 90° in relation to the line connection (clockwise) 19) Line connection "B"
2) Ø D4 max. 0.5 mm deep 20) Line connection "M"
3) Thread size does not comply with ISO 6022;

Dimensions: Round flange at base CSH2...XE: MF4

(dimensions in mm)
CSH2...XE: MF4: ØAL 40 ... 100 mm

CSH2...XE: MF4: ØAL 125 ... 320 mm


Dimensions: Round flange at base CSH2...XE: MF4

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA X* L4

2) 4), 19) 4), 20) max.
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18 1000 3
50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18 1000 3
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 2000 0
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 2000 0
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 3000 0
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 3000 21.5
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 3000 25.5
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 3000 25.5
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 3000 32
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 3000 32
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 3000 38
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 3000 38
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 3000 44
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 3000 44
ØAL ØMM L6 ØD2 D1 ZP NX ØFB ØFC ØUC ØRA VE

max. js13 H13 js13 ‒1
40 6) 25/28 166 18 80 262 28 11 115 138 52 29
50 32/36 166 20 96 278 28 13.5 132 155 63 29
63 40/45 166 0 96 313 28 13.5 150 175 75 32
80 50/56 166 0 96 350 32 17.5 180 210 90 36
100 63/70 138 0 96 390 36 22 212 250 110 41
125 80/90 131 33 96 445 55 22 250 290 132 45
140 90/100 121 40 96 485 60 26 285 330 145 45
160 100/110 113.5 40 96 525 65 26 315 360 160 50
180 110/125 106 48 96 570 70 33 355 410 185 55
200 125/140 100 48 96 616 76 33 385 440 200 61
220 6) 140/160 88 57 96 715 88 39 435 500 235 71
250 160/180 86 57 96 730 90 39 475 540 250 71
280 6) 180/200 61 66 96 857 115 45 555 630 295 88
320 200/220 61 66 96 865 115 45 600 675 320 88

by 90° in relation to the line connection (clockwise) 19) Line connection "B"
2) Ø D4 max. 0.5 mm deep 20) Line connection "M"

Dimensions: Trunnion CSH2...XE: MT4

(dimensions in mm)
CSH2...XE: MT4

Dimensions for cylinder with piston rod extension "LY"

in retracted condition


Dimensions: Trunnion CSH2...XE: MT4

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA X* L5 D1

2) 4), 19) 4), 20) max. max.
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18 1000 166 80
50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18 1000 166 96
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 2000 166 96
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 2000 166 96
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 3000 166 96
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 3000 166 96
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 3000 166 96
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 3000 166 96
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 3000 166 96
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 3000 166 96
220 6) 140/160 M125x4 125 120/140 355 273 65 G1 1/2 M48x2 3) 244 326 174 42 3000 166 96
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 3000 166 96
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 3000 166 96
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 3000 166 96
ØAL ØMM ZB X* XV 14) XV 12) XV 12) BD UV ØTD TL TM r ØRA VE

max. min. average min. max. 15) f8 js16 h12
40 6) 25/28 239 22 143+X*/2 154 140+X* 38 97 25 20 95 0.8 52 29
50 32/36 254 32 158+X*/2 174 151+X* 38 111 32 25 112 0.8 63 29
63 40/45 299 47 178.5+X*/2 202 167+X* 48 129 40 32 125 1 75 32
80 50/56 332.5 58 197.5+X*/2 226.5 180.5+X* 58 163 50 40 150 1 90 36
100 63/70 362 79 219.5+X*/2 259 195+X* 78 188 63 50 180 1.2 110 41
125 80/90 410 91 255.5+X*/2 301 210+X* 98 234 80 63 224 1.2 132 45
140 90/100 440 121 275.5+X*/2 336 215+X* 118 257 90 70 265 1.5 145 45
160 100/110 472.5 142 302.5+X*/2 373.5 231.5+X* 128 287 100 80 280 1.5 160 50
180 110/125 510 158 326+X*/2 405 247+X* 138 328 110 90 320 1.5 185 55
200 125/140 550 204 359+X*/2 461 257+X* 178 343 125 100 335 1.5 200 61
220 6) 140/160 637 200 407+X*/2 507 307+X* 180 393 160 125 385 1.5 235 71
250 160/180 650 210 420+X*/2 525 315+X* 180 433 160 125 425 1.5 250 71
280 6) 180/200 752 241 477.5+X*/2 598 357+X* 220 486 200 160 480 2 295 88
320 200/220 760 245 477.5+X*/2 600 355+X* 220 536 200 160 530 2 320 88
ØAL = Piston Ø Preferred XV dimension: Observe trunnion position in cylinder

ØMM = Piston rod Ø center XVmin. and XVmax.
14) XV
X* = Stroke length cent. recommendation: Trunnion position in cylinder center
X*min. = min. stroke length classes 342 according to ISO 9013 Thermal cutting
17) Trunnion nut with AL Ø ≥ 125 mm either at head or at base side
2) Ø D4 max. 0.5 mm deep depending on the position of the trunnion (XV).
4) Flange connections see separate tables on pages 34 and 35
5) Throttle valve only with end position cushioning "E" Important installation information!
6) Piston Ø not standardized During installation, it must be ensured that the trunnion
10) Observe the min. stroke length "X*
min." bearings are installed up to the trunnion shoulders. Any
11) Double-acting cylinder not standardized
non-compliance may reduce the product's service life.
12) When ordering, always specify the "XV" dimension in the clear
text.
Dimensions: Foot mounting CSH2...XE: MS2

(dimensions in mm)
CSH2...XE MS2


Dimensions: Foot mounting CSH2...XE: MS2

(dimensions in mm)
ØAL ØMM KK A NV ØD ØDA ØD4 EE EE Y PJ X1 WA X*

2) 4), 19) 4), 20) max.
40 6) 25/28 M20x1.5 28 19/22 88 52 34 G1/2 M22x1.5 83 120 41 18 1000
50 32/36 M27x2 36 27/30 102 62 34 G1/2 M22x1.5 98 120 48.5 18 1000
63 40/45 M33x2 45 32/36 120 78 42 G3/4 M27x2 112 133 56.5 21 2000
80 50/56 M42x2 56 41/46 145 95 42 G3/4 M27x2 120 155 69.5 24 2000
100 63/70 M48x2 63 50/60 170 125 47 G1 M33x2 134 171 82 27 3000
125 80/90 M64x3 85 65/75 206 150 47 G1 M33x2 153 205 100.5 31 3000
140 90/100 M72x3 90 75/85 226 170 58 G1 1/4 M42x2 166 219 109.5 31 3000
160 100/110 M80x3 95 85/95 265 190 58 G1 1/4 M42x2 185 235 129.5 35 3000
180 110/125 M90x3 105 95/110 292 210 58 G1 1/4 M42x2 194 264 143.5 40 3000
200 125/140 M100x3 112 110/120 306 235 58 G1 1/4 M42x2 220 278 150.5 40 3000
220 6) 140/160 M125x4 125 120/140 355 270 65 G1 1/2 M48x2 3) 244 326 174 42 3000
250 160/180 M125x4 125 140/160 395 305 65 G1 1/2 M48x2 3) 257 326 194 42 3000
280 6) 180/200 M160x4 160 160/180 445 343 65 G1 1/2 M48x2 3) 290 375 220.5 48 3000
320 200/220 M160x4 160 180/200 490 394 65 G1 1/2 M48x2 3) 282 391 243 48 3000
ØAL ØMM L5 D1 XS ZB SS X* S S1 ØSB ST TS US LH L1 ØRA VE

max. max. min. H13 js13 15) 15)
40 6) 25/28 166 80 118 239 50 1 30 15 11 32 110 140 45 93 52 29

50 32/36 166 96 135.5 254 45 1 35 17.5 11 37 130 161 55 110 63 29
63 40/45 166 96 154 299 49 1 40 20 13.5 42 150 183 65 129 75 32
80 50/56 166 96 171.5 332.5 52 2 50 25 17.5 47 180 220 75 149 90 36
100 63/70 166 96 189 362 61 3 60 30 22 57 210 260 90 181 110 41
125 80/90 166 96 218 410 75 1 70 35 26 67 255 313 105 215 132 45
140 90/100 166 96 240.5 440 70 19 85 42.5 30 72 290 359 115 235 145 45
160 100/110 166 96 270 472.5 65 44 105 52.5 33 77 330 402 135 277 160 50
180 110/125 166 96 291.5 510 69 50 115 57.5 40 92 360 445 150 305 185 55
200 125/140 166 96 322.5 550 73 56 125 62.5 40 97 385 471 160 322 200 61
220 6) 140/160 166 96 369.5 637 75 100 155 77.5 45 102 445 541 185 373 235 71
250 160/180 166 96 382.5 650 75 100 155 77.5 52 112 500 610 205 414 250 71
280 6) 180/200 166 96 415.5 752 124 51 155 77.5 52 142 550 661 235 469 295 88
320 200/220 166 96 435 760 85 125 190 95 62 142 610 732 255 512 320 88

ØMM = Piston rod Ø 10) Observe the min. stroke length "X*min."
X* = Stroke length 12) Recess 2 mm deep, for hexagon socket head cap screws;
X*max. = max. stroke length ISO 4762 – The screws must not be subjected to shear force.
X*min. = min. stroke length Force introduction via additional external fitting strip
by 90° in relation to the line connection (clockwise) classes 342 according to ISO 9013 Thermal cutting
2) Ø D4 max. 0.5 mm deep
4) Flange connections see separate tables on pages 34 and 35

Dimensions: Flange ports

(dimensions in mm)
CDH2...XC / CSH2...XE

CGH2...XC

Dimensions for rectangular flange according Dimensions for square flange according to ISO 6164
to ISO 6162-1 tab. 2 type 1 table 1 and ISO 6164 table 2
and ISO 6162-2 tab. 2 type 1


Dimensions: Flange ports

(dimensions in mm)
Version "F" 6) Version "K" 7)

ISO 6162-1 tab. 2 type 1 (200 ... 350 bar) (≙ SAE 3000 PSI) ISO 6164 tab. 1 (250 bar)
Y PJ X1 Ød3 Ød3 4) c w d1 t1 1) t1 2) p3) Y PJ X1 Ød3 w d1 t1 1) t1 2) p 3)
ØAL PK ±0.25 ±0.25 PK ±0.25
40 – – – – – – – – – – – 82 122 40.5 10 24.7 M6 12.5 10 250

50 – – – – – – – – – – – 97 122 48 10 24.7 M6 12.5 12.5 250
63 111 135 55 13 1/2" 38.1 17.5 M8 16 16 350 111 135 57 13 29.7 M8 16 16 250
80 123.5 148 68 13 1/2" 38.1 17.5 M8 16 16 350 123.5 148 69.5 13 29.7 M8 16 16 250
100 133 173 79 19 3/4" 47.6 22.3 M10 20 20 350 133 173 81.5 19 35.4 M8 16 16 250
125 153 205 98 25 1" 52.4 26.2 M10 20 20 350 157 197 100 19 35.4 M8 16 16 250
140 162 227 107 32 1 1/4" 58.7 30.2 M10 20 20 250 162 227 109 25 43.8 M10 20 20 250
160 181.5 242 127 32 1 1/4" 58.7 30.2 M10 20 20 250 181.5 242 128.5 25 43.8 M10 20 20 250
180 193 266 139 38 1 1/2" 69.9 35.7 M12 24 24 200 194 264 142 32 51.6 M12 24 24 250
200 219 280 146.5 38 1 1/2" 69.9 35.7 M12 24 24 200 220 278 148.5 32 51.6 M12 24 24 250
Version "D" 8) Version "H" 8)
ISO 6162-2 tab. 2 type 1 (400 bar) (≙ SAE 6000 PSI) ISO 6164 tab.2 (400 bar)
Y PJ X1 Ød3 Ød3 5) c w d1 t1 1) t1 2) p 3) Y PJ X1 Ød3 w d1 t1 1) t1 2) p 3)
ØAL PK ±0.25 ±0.25 PK ±0.25
40 – – – – – – – – – – – 82 122 40.5 10 24.7 M6 12.5 10 400

50 – – – – – – – – – – – 97 122 48 10 24.7 M6 12.5 12.5 400
63 – – – – – – – – – – – 111 135 57 13 29.7 M8 16 16 400
80 120 155 67 13 1/2" 40.5 18.2 M8 16 14 400 123.5 148 69.5 13 29.7 M8 16 16 400
100 134 171 80.5 13 1/2" 40.5 18.2 M8 16 16 400 133 173 81.5 19 35.4 M8 16 16 400
125 153 205 97 19 3/4" 50.8 23.8 M10 20 20 400 157 197 100 19 35.4 M8 16 16 400
140 162 227 107 25 1" 57.2 27.8 M12 24 24 400 162 227 109 25 43.8 M10 20 20 400
160 181.5 242 127 25 1" 57.2 27.8 M12 24 24 400 181.5 242 128.5 25 43.8 M10 20 20 400
180 194 264 139.5 32 1 1/4" 66.6 31.8 M14 26 26 400 194 264 142 32 51.6 M12 24 24 400
200 220 278 147 32 1 1/4" 66.6 31.8 M14 26 26 400 220 278 148.5 32 51.6 M12 24 24 400
220 244 326 168 38 1 1/2" 79.3 36.5 M16 30 30 400 244 326 171 38 60.1 M16 30 30 400
250 257 326 189 38 1 1/2" 79.3 36.5 M16 30 30 400 257 326 192 38 60.1 M16 30 30 400
280 290 375 215 38 1 1/2" 79.3 36.5 M16 30 30 400 290 375 218 38 60.1 M16 30 30 400
320 282 391 236 51 2" 96.8 44.5 M20 36 36 400 282 391 240 51 69.3 M16 30 30 400
Main dimensions see pages 14 to 33 4) Flange connection according to ISO 6162-1 tab. 2 type 1
corresponds to flange connection according to SAE 3000 PSI
5) Flange connection according to ISO 6162-2 tab. 2 type 1
ØAL = Piston Ø
X* = Stroke length corresponds to flange connection according to SAE 6000 PSI
6) Version "F" with piston Ø 125 ... 200 mm not standardized
1) Thread depth for seal design M, T, and S
7) Version "K" with piston Ø 40 ... 50 mm and
2) Thread depth for seal design A and B
3) piston Ø 180 ... 200 mm not standardized
Max. operating pressure for related flanges in bar
8) Versions "D" and "H" not standardized

Dimensions: Bleeding / measuring coupling

(dimensions in mm)
By default, a patented safety vent against unintended with check valve for pressure measurement
screwing out in head and base is delivered for all cylinders. or contamination-free bleeding. Measuring coupling with
The port allows for the installation of a measuring coupling check valve function, i.e. it can also be connected when
the system is pressurized.



Scope of delivery: Measuring coupling G1/4
MEASURING COUPLING AB 20-11/K1 G1/4 with seal ring made of NBR
Material no. R900009090
MEASURING COUPLING AB 20-11/K1V G1/4 with seal ring made of FKM

Dimensions: Throttle valve

(dimensions in mm)
ØAL 40 50 63 80 100 125 140 160 180 200 220 250 280 320
Protrusion A 1) 1 0 0 0 0 0 0 0 0 0 9.5 0 0 0
Nominal width 4 4 4 5 5 8 8 8 8 8 20 20 20 20
ØAL = Piston Ø

Protrusion A in closed condition

Position measurement system
Types of mounting
MF3, MF4, MT4, MS2

1) For analog output:

6-pole Amphenol mating connector
(mating connector is not included in the scope of delivery, must be ordered separately)
1) For digital output:

7-pole Amphenol mating connector
(mating connector is not included in the scope of delivery, must be ordered separately)
Pin assignment
Position measurement system (analog output) Pin Cable Signal / current Signal / voltage
Connector (view to pin side) 1 gray 4 … 20 mA 0 … 10 V
2 pink DC ground DC ground
3 yellow not assigned not assigned

4 green DC ground DC ground
5 brown +24 V DC +24 V DC
(+20% / –15%) (+20% / –15%)
6 white DC ground (0 V) DC ground (0 V)
Position measurement system (digital output) Pin Cable Signal / SSi

Connector (view to pin side) 1 gray Data (–)
2 pink Data (+)
3 yellow Clock (+)
4 green Clock (–)
5 brown +24 V DC (+20 % / –15 %)
6 white DC ground (0 V)

7 – not assigned

Position measurement system
The position measurement system that is pressure-resistant

up to 500 bar works in a contactless and absolute manner.
The basis of this position measurement system is the
magnetostrictive effect. Here, the coincidence of two
magnetic fields triggers a torsion pulse.
This pulse runs on the waveguide inside the gauge from the
measuring point to the sensor head. The running time
is constant and almost temperature-independent.
It is proportional to the position of the solenoid and thus
a measure for the actual position value and is converted
in the sensor into a direct analog or digital output.
Technical data
Operating pressure bar 250

Analog output V 0 … 10
Load resistance kΩ ≥5
Resolution unlimited
Analog output mA 4 … 20
Load resistance Ω 0 … 500
Resolution unlimited
Digital output SSI 24 bit gray-coded
Resolution µm 5
Direction of measurement asynchronously forward
Linearity Analog % ≤ ±0.02% (referred to measurement length)
(absolute accuracy) mm min. ±0.05
Digital % ≤ ±0.01% (referred to measurement length)
mm min. ±0.04
Reproducibility % ±0.001 (referred to measurement length)
mm min. ±0.0025
Hysteresis mm ≤ 0.004
Supply voltage V DC 24 (±10 % with analog output)
Current consumption mA 100
Residual ripple % s-s ≤1
V DC 24 (+20 %/–15 % with digital output)
Current consumption mA 70
Residual ripple % s-s ≤1
Protection class Pipe and flange IP 67
Sensor electronics IP 65
Ambient temperature Sensor electronics °C –20 … +75
Derating Sensor electronics 6.5 K/W ≥ 49 °C

Position / dimensions: Equipotential bonding

(dimensions in mm)
Mounting ring for equipotential bonding

at the piston rod (KK1)
Piston Ø 40 … 125 mm

Equipotential bonding at the piston rod (KK1)


Equipotential bonding at the cylinder (KK2)

CDH2…XC
KK2 KK2 KK2
KK2 KK2 KK2
CGH2…XC
KK2 KK2 KK2

Position / dimensions: Equipotential bonding

(dimensions in mm)
CSH2…XE
KK2 KK2
KK3 KK3
KK2 KK2
KK3 KK3
KK1 and KK2

ØAL ØMM RA1 LA1 KK1 / KK2
25 48
40 12 M6
28 50
32 56
50 12 M6 Included in the
36 60 scope of delivery
40 68
63 12 M6 Not included
45 72 in the scope
50 80 KK1 / KK2 of delivery
80 13 M6
56 85
63 95
100 18 M6
70 100
80 110
125 18 M6
90 120
140 … 320 – – – M8
ØAL = Piston Ø
ØMM = Piston rod Ø
KK3 = cable clamp at the position measurement system

Dimensions: Swivel head CGKD (clampable)

(dimensions in mm)
ISO 8132

ØAL Type Material no. Nominal force AV N CH EF ØCN 2) EN EU

kN min. max. js13 max. H7 h12 max.
40 CGKD 25 R900323332 32 29 31 65 32 25 25 22
50 CGKD 32 R900322049 50 37 38 80 40 32 32 28
63 CGKD 40 R900322029 80 46 47 97 50 40 40 34
80 CGKD 50 R900322719 125 57 58 120 63 50 50 42
100 CGKD 63 R900322028 200 64 70 140 72.5 63 63 53.5
125 CGKD 80 R900322700 320 86 91 180 92 80 80 68
140 CGKD 90 7) R900325702 400 91 100 195 101 90 90 72
160 CGKD 100 R900322030 500 96 110 210 114 100 100 85.5
180 CGKD 110 7) R900308153 635 106 125 235 129 110 110 88
200 CGKD 125 R900322026 800 113 135 260 160 125 125 105
220 CGKD 160 R900300718 1,520 126 165 310 200 160 160 133
250 CGKD 160 R900300718 1,520 126 165 310 200 160 160 133
280 CGKD 200 R900324814 2,000 161 215 390 250 200 200 165
320 CGKD 200 R900324814 2,000 161 215 390 250 200 200 165

Dimensions: Swivel head CGKD (clampable)

(dimensions in mm)
ØAL Type KK LF Clamping screw MA 3) m 4) C0 5) Fadm 6)

min. ISO 4762-10.9 Nm kg kN kN
40 CGKD 25 M20x1.5 25.5 M8x20 30 0.65 78 28.8
50 CGKD 32 M27x2 30 M10x25 59 1.15 114 42.1
63 CGKD 40 M33x2 39 M10x30 59 2.1 204 75.3
80 CGKD 50 M42x2 47 M12x35 100 4 310 114.4
100 CGKD 63 M48x2 58 M16x40 250 7.2 430 158.7
125 CGKD 80 M64x3 74 M20x50 490 15 695 256.5
140 CGKD 90 7) M72x3 85 M20x60 490 19 750 276.8
160 CGKD 100 M80x3 94 M24x60 840 25.5 1060 391.1
180 CGKD 110 7) M90x3 105 M24x60 840 36.5 1200 442.8
200 CGKD 125 M100x3 116 M24x70 840 52.5 1430 527.7
220 CGKD 160 M125x4 145 M24x80 840 82.5 2200 811.8
250 CGKD 160 M125x4 145 M24x80 840 82.5 2200 811.8
280 CGKD 200 M160x4 190 M30x100 1700 168 3650 1346.9
320 CGKD 200 M160x4 190 M30x100 1700 168 3650 1346.9
Note:
Geometry and dimensions may differ depending on the
manufacturer. All graphical representations are examples.
In case of combination with other mounting elements, the
usability must be checked.
ØAL = Piston Ø 4) m = Weight of swivel head in kg

1) Lubricating nipple, cone head form A according to DIN 71412 5) CO = static load rating of the tilt head
2) Related bolt Ø m6 6) Fadm = m
ax. admissible load of the tilt head with oscillatory
3) M
A =T
ightening torque or alternating loads
The tilt head must always be screwed against the shoulder 7) Not contained in the standard
of the piston rod. Afterwards, the clamping screws must
be tightened with the specified tightening torque.

Kinking
For the admissible stroke length with flexibly guided load Explanation:
and a factor of 3.5 for safety against kinking, please refer E = Module of elasticity in N/mm2
to the relevant table. For other installation positions of the = 2.1 x 105 for steel
l = Geometrical moment of inertia in mm4
cylinder, the admissible stroke length must be interpolated.
d4•π
Admissible stroke length for non-guided load on request. =
for circular cross-section = 0.0491 • d4
64
Kinking calculations are carried out according to the ν = 3.5 (safety factor)
following formulas: LK = free bending length in mm (depending on the type of-mounting
1. Calculation according to Euler see sketches A, B, C)
π2 • E • I d = Piston rod Ø in mm
F = if λ > λg
λ = Slenderness ratio
ν • LK2
4 • LK E
2. Calculation according to Tetmajer = λg = π
d 0.8 • Re
d 2 • π (335‒0.62 • λ) Re = Yield strength of the piston rod material
F= if λ ≤ λg
4•ν
Influence of the type of mounting on the bending length:

LK = 0.7 L LK = L LK = 2 L
Admissible stroke length (dimensions in mm)

Type of mounting CDH2…XC: MP3, MP5
ØAL ØMM admissible stroke length with
100 bar 160 bar 250 bar Installation position
0° 45° 90° 0° 45° 90° 0° 45° 90°
25 195 200 215 130 135 140 40 45 55
40 0°
28 385 400 445 295 300 320 215 220 225
32 380 390 430 280 285 300 195 200 205
50
36 505 525 595 395 405 430 290 295 305
40 480 500 550 365 370 385 255 260 265
63
45 640 660 750 505 515 550 380 385 395
50 590 615 690 455 465 495 330 335 345
80
56 765 800 930 615 630 685 470 475 495
63 750 780 910 595 610 660 445 455 470
100
70 940 985 1195 775 800 885 605 615 650
80 970 1015 1200 780 805 880 595 605 635
125 45°

90 1235 1300 1610 1030 1070 1200 825 840 895

90 1075 1130 1360 875 905 1000 675 685 725
140
100 1335 1405 1770 1120 1165 1325 900 920 985
100 1175 1230 1480 955 985 1085 735 750 785
160
110 1430 1500 1875 1195 1240 1400 955 975 1040
110 1250 1310 1570 1010 1045 1150 775 790 830
180
125 1620 1710 2160 1365 1420 1620 1100 1125 1205
125 1435 1510 1860 1180 1220 1365 915 935 990
200
140 1795 1900 2450 1525 1590 1840 1240 1270 1370
140 1620 1710 2180 1360 1415 1630 1090 1120 1200

220 90°
160 2075 2200 3000 1810 1890 2280 1510 1560 1730
160 1805 1910 2490 1520 1590 1850 1220 1250 1360
250
180 2250 2395 3300 1960 2060 2500 1630 1690 1880
180 2075 2200 2900 1775 1880 2170 1450 1490 1620
280
200 2510 2670 3700 2200 2310 2820 1850 1920 2140
200 2135 2270 3030 1820 1900 2260 1470 1510 1660 1) Adm.
320
220 2550 2720 3820 2230 2340 2880 1860 1930 2170 Stroke length

Type of mounting CDH2…XC / CGH2…XC / CSH2…XE 2): MF3

0° 45° 90° 0° 45° 90° 0° 45° 90°
25 895 915 980 730 735 760 440 450 510
40 0°
28 1400 1415 1630 1180 1205 1275 970 980 1010
32 1440 1490 1670 1210 1230 1300 985 995 1025
50
36 1760 1830 2000 1510 1545 1675 1255 1270 1320
40 1735 1800 2000 1475 1510 1620 1215 1230 1270
63
45 2000 2000 2000 1830 1880 2080 1540 1560 1640
50 2000 2000 2000 1810 1850 1995 1495 1515 1570
80
56 2000 2000 2000 2000 2000 2000 1870 1900 2000
63 2580 2690 3000 2235 2300 2550 1875 1910 2010
100
70 3000 3000 3000 2690 2780 3000 2300 2350 2520

80 3000 3000 3000 2840 2930 3000 2400 2450 2590
125 45°
90 3000 3000 3000 3000 3000 3000 3000 3000 3000
90 3000 3000 3000 3000 3000 3000 2700 2760 2950
140
100 3000 3000 3000 3000 3000 3000 3000 3000 3000
100 3000 3000 3000 3000 3000 3000 2920 2980 3000
160
110 3000 3000 3000 3000 3000 3000 3000 3000 3000
110 3000 3000 3000 3000 3000 3000 3000 3000 3000
180
125 3000 3000 3000 3000 3000 3000 3000 3000 3000
125 3000 3000 3000 3000 3000 3000 3000 3000 3000
200
140 3000 3000 3000 3000 3000 3000 3000 3000 3000

140 5400 5680 6000 4800 4980 5780 4120 4220 4560
220 90°
160 6000 6000 6000 5820 6000 6000 5150 5330 6000
160 5850 6000 6000 5270 5500 6000 4600 4740 5250
250
180 6000 6000 6000 6000 6000 6000 5650 5850 6000
180 6000 6000 6000 6000 6000 6000 5270 5420 5970
280
200 6000 6000 6000 6000 6000 6000 6000 6000 6000
200 6000 6000 6000 6000 6000 6000 5950 6000 6000 1) Adm.
320
220 6000 6000 6000 6000 6000 6000 6000 6000 6000 Stroke length
Type of mounting CDH2…XC / CSH2…XE 2): MF4

0° 45° 90° 0° 45° 90° 0° 45° 90°
25 325 340 370 245 250 260 105 110 140
40 0°
28 565 590 695 465 475 520 365 370 385
32 600 625 715 485 495 530 370 375 390
50
36 755 790 950 630 650 715 505 515 540
40 730 765 905 600 615 675 470 480 500
63
45 920 965 1190 780 805 905 630 645 685
50 910 950 1130 750 775 845 595 605 630
80
56 1125 1185 1470 960 990 1120 785 800 850
63 1120 1175 1460 945 980 1105 770 785 835
100
70 1350 1430 1860 1175 1220 1420 980 1000 1090
80 1430 1510 1910 1225 1270 1450 1000 1025 1100

125 45°
90 1750 1855 2490 1540 1610 1910 1300 1340 1470
90 1585 1675 2170 1370 1425 1650 1135 1165 1260
140
100 1895 2010 2750 1675 1755 2110 1425 1470 1630
100 1725 1820 2340 1490 1545 1780 1230 1260 1360
160
110 2030 2150 2900 1785 1870 2230 1510 1560 1720
110 1855 1960 2510 1595 1660 1910 1315 1350 1450
180
125 2300 2440 3350 2040 2130 2580 1735 1790 1990
125 2105 2230 2950 1830 1910 2250 1530 1570 1715
200
140 2535 2700 3000 2260 2370 2920 1940 2010 2255

140 2250 2400 3350 1990 2090 2550 1685 1740 1950
220 90°
160 2800 2990 4500 2530 2680 3480 2220 2310 2700
160 2600 2770 3900 2310 2430 3000 1975 2040 2300
250
180 3130 3350 5050 2840 3000 3910 2500 2600 3040
180 2850 3050 4400 2550 2680 3370 2190 2270 2600
280
200 3370 3610 5550 3070 3250 4300 2700 2820 3330
200 3070 3270 4750 2750 2890 3650 2150 2460 2810 1) Adm.
320
220 3560 3820 5850 3250 3430 4550 2860 2980 3530 Stroke length

Type of mounting CDH2…XC / CGH2…XC / CSH2…XE 2): MT4 trunnion in cylinder center
0° 45° 90° 0° 45° 90° 0° 45° 90°
25 340 345 365 250 255 260 130 135 145
40 0°
28 590 605 665 470 480 500 365 370 375
32 600 615 670 470 480 495 355 360 365
50
36 770 795 890 625 635 670 485 490 505
40 740 765 845 590 600 630 450 455 465
63
45 940 975 1115 770 790 845 610 620 640
50 920 950 1055 735 750 790 570 575 590
80
56 1155 1195 1375 950 975 1045 755 765 790
63 1145 1190 1365 940 960 1030 740 750 775
100
70 1400 1460 1740 1180 1210 1330 955 970 1015
80

1470 1530 1780 1220 1250 1350 970 985 1020
125 45°
90 1820 1910 2320 1550 1600 1780 1275 1300 1370
90 1640 1710 2020 1370 1410 1540 1100 1120 1170
140
100 1980 2080 2570 1700 1755 1970 1400 1430 1515
100 1780 1850 2180 1485 1520 1660 1190 1210 1260
160
110 2110 2210 2710 1800 1860 2080 1480 1510 1595
110 1910 1990 2340 1590 1635 1780 1275 1295 1350
180
125 2405 2530 3000 2065 2130 2400 1710 1740 1850
125 2180 2280 2740 1840 1890 2090 1490 1510 1590
200
140 2660 2800 3000 2300 2380 2720 1915 1960 2100

140 2490 2510 3150 2050 2120 2400 1685 1720 1835
220 90°
160 3000 3170 4230 2640 2750 3260 2240 2310 2530
160 2730 2870 3640 2350 2440 2790 1950 1990 2140
250
180 3320 3520 4720 2940 3060 3650 2500 2570 2830
180 3040 3210 4140 2640 2750 3170 2210 2260 2440
280
200 3620 3840 5210 3210 3360 4040 2750 2830 3140
200 3250 3430 4455 2820 2930 3410 2360 2420 2620 1) Adm.
320
220 3800 4030 5500 3370 3530 4250 2880 2970 3290 Stroke length
Type of mounting CDH2…XC / CGH2…XC / CSH2…XE 2): MS2

0° 45° 90° 0° 45° 90° 0° 45° 90°
25 825 840 885 645 650 665 370 375 410
40 0°
28 1305 1350 1535 1085 1110 1180 875 885 910
32 1330 1375 1560 1095 1120 1190 875 885 910
50
36 1645 1715 2030 1395 1430 1560 1140 1160 1210
40 1610 1670 1950 1345 1380 1490 1085 1100 1145
63
45 1980 2000 2000 1700 1750 1950 1410 1435 1510
50 1980 2000 2000 1665 1710 1850 1350 1370 1425
80
56 2000 2000 2000 2000 2000 2000 1730 1760 1860
63 2420 2535 3000 2080 2140 2390 1720 1750 1850
100
70 2880 3000 3000 2530 2630 3000 2140 2190 2360
80 3000 3000 3000 2660 2750 3000 2220 2270 2410
125 45°
90 3000 3000 3000 3000 3000 3000 2810 2890 3000

90 3000 3000 3000 2970 3000 3000 2490 2550 2740

140
100 3000 3000 3000 3000 3000 3000 3000 3000 3000
100 3000 3000 3000 3000 3000 3000 2690 2750 2950
160
110 3000 3000 3000 3000 3000 3000 3000 3000 3000
110 3000 3000 3000 3000 3000 3000 2890 2960 3000
180
125 3000 3000 3000 3000 3000 3000 3000 3000 3000
125 3000 3000 3000 3000 3000 3000 3000 3000 3000
200
140 3000 3000 3000 3000 3000 3000 3000 3000 3000

140 5090 5370 6000 4490 4670 5470 3820 3910 4260
220 90°
160 6000 6000 6000 5510 5800 6000 4850 5020 5750
160 5520 5860 6000 4940 5170 6000 4270 4410 4920
250
180 6000 6000 6000 6000 6000 6000 5320 5520 6000
180 6000 6000 6000 5700 5960 6000 4930 5070 5630
280
200 6000 6000 6000 6000 6000 6000 6000 6000 6000
200 6000 6000 6000 5890 6000 6000 4750 5310 6000 1) Adm.
320
220 6000 6000 6000 6000 6000 6000 6000 6000 6000 Stroke length
With longer strokes, an extended guide and/or the use of guide rings may be reasonable for increasing the service life, depending on the
respective case of application and installation position. Recommendation on request.
2) With CSH2…XE, observe the maximum stroke length "X*
max.", pages 26 to 33


End position cushioning:
The objective is to reduce the velocity of a moved mass, the with version "D". End position cushioning version "E" allows
center of gravity of which lies on the cylinder axis, to a level cycle times to be optimized. The max. damping capacity
at which neither the cylinder nor the machine into which can only be achieved when the throttle valve is closed.
the cylinder is installed is damaged. For velocities above The calculation depends on the factors weight, velocity,
20 mm/s, we recommend the use of an end position system pressure and installation position. For this reason,
cushioning feature, which absorbs energy without requiring mass and velocity are used to determine the characteristic
the use of an additional device. It must, however, always Dm and system pressure and installation position
be checked whether end position cushioning is also to determine the characteristic Dp.
required for lower velocities with large masses. These two characteristics are used for verifying the
With stroke lengths smaller than the damping lengths, we admissible damping capacity in the "damping capacity"
recommend selecting the cylinder without end position diagram. The intersection point of the characteristics Dm
cushioning. With cylinder strokes within the damping and Dp must always be below the damping capacity curve
lengths, restrictions with regard to speed / cycle time are of the selected cylinder. The values in the diagrams refer
possible. to an average oil temperature of + 45 to +65 °C with the
Damping capacity: throttle valve being closed.
When decelerating masses via end position cushioning, the For special applications with very short stroke times, high
structural-inherent damping capacity must not velocities or large masses, cylinders with special end
be exceeded. Cylinders with end position cushioning can position cushioning versions can be offered on request.
achieve their full damping capacity only over the entire When fixed or adjustable stops are used, special measures
stroke length. must be taken!
With the adjustable end position cushioning version "E",

a throttle valve is additionally provided when compared

Formulas:
m
Dm = ; K = kv (0.5–v)
10K
m = moved weight in kg

v = stroke velocity in m/s
kv = see table page 47

Extension for CDH2…XC and CSH2…XE

m • 9.81 • sinα
Dp = pS –
A1 • 10
Retraction for CDH2…XC, CGH2…XC and CSH2…XE;

Extension for CGH2…XC
m • 9.81 • sinα
Dp = pS +
A3 • 10
pS = system pressure in bar

A1 = piston area in cm2 (see page 11)
A3 = annulus area in cm2 (see page 11)
α = angle to the horizontal in degree

α
α

Damping length
ØAL mm 40 50 63 80 100 125 140 160 180 200 220 250 280 320
Head side 21 20 23 25 25 25 33 33 37 37 76 81 86 90
Base side 21 20 23 25 25 25 33 33 37 37 76 81 86 90

ØAL mm 40 50 63 80 100 125 140 160 180 200 220 250 280 320
kv 1 2.85 2.97 2.56 2.82 3.51 3.02 2.53 2.65 2.91 2.76 2.85 2.95 3.11 3.13
kv 2 3.1 3.25 2.85 2.85 3.52 2.91 2.53 2.93 2.95 2.95 2.93 3.1 3.12 3.07
kv 3 2.95 3.1 2.73 3.1 3.51 2.95 2.51 2.91 2.95 2.91 2.93 2.93 3.15 3.25
Damping capacity: Extension for CDH2…XC and CSH2…XE, with kv 1

Dm →

1)

Dp →
ØAL = Piston Ø
1) If with standard applications the calculated intersection point
of Dm and Dp is within the marked area, we recommend designing
the cylinder without end position cushioning.

Damping capacity: Retraction for CDH2…XC, CGH2…XC and CSH2…XE; extension for CGH2…XC with kv 2

Dm →

1)

Dp →
Damping capacity: Retraction for CDH2…XC, CGH2…XC and CSH2…XE; extension for CGH2…XC with kv 3

Dm →

1)

Dp →
ØAL = Piston Ø
1) If with standard applications the calculated intersection point
of Dm and Dp is within the marked area, we recommend designing
the cylinder without end position cushioning.

Selection criteria for seals
Seal versions
Work and environmental conditions
M A B T S
Medium HL, HLP / operating temperature medium –20 °C to +80 °C ++ ++ ++ ++ ++

Medium / temperature
Medium HFA / operating temperature medium +5 °C to +55 °C +/– + +/– ++ +/–
Medium HFC / operating temperature medium –20 °C to +60 °C – +/– – ++ –
Medium HFDR / operating temperature medium –15 °C to +80 °C – – ++ – ++
Ambient and rod temperature in the area of the piston rod with version
CDH2..XC and CGH2..XC from –20 °C to +80 °C 1) / ++ ++ + 2) + ++ 2)
with version CSH2..XE from –20 °C to +75 °C 1)
static holding function more than 10 minutes:

++ ++ ++ + +
Attention! Application- and temperature-dependent
Static holding function short-time < 1 minute ++ ++ ++ ++ ++
Robust application conditions: Steel works, mining, thin ice ++ ++ ++ – –
Zero point control, hardly any amplitude, frequency max. 5 Hz,

Function / velocity...
– – – ++ ++
not longer than 5 minutes
Cylinder velocity min. 0.001 m/sec stick-slip behavior ++ – – ++ ++
Cylinder velocity from 0.01 m/sec to 0.5 m/sec 3) ++ + + ++ ++
Cylinder velocity > 0.5 m/sec to max. 0.8 m/sec 3) – – – ++ ++
Stroke > 1.0 m +/– ++ ++ ++ ++
Standstill period (wear) ++ +/– – ++ ++
Undissolved air in the oil 4) – – – + +
++ = very good + = good +/– = conditional, depending on the application parameters – = inappropriate
General technical data in corresponding data sheets will 1) Moreover, observe the corresponding medium temperature range
remain valid! 2) Lower temperature limit –15 °C
3) Standard line connections not designed for that velocity
Generally, a medium temperature of approx. 40 °C is recommended. 4) – Seal is destroyed / + Seal is not directly destroyed,
The specified values are to be regarded as guidelines; depending
leakage may occur
on the application, it may be necessary to check the suitability of the
seal system.

Seal kits
CDH2…XC – standard
Material no. for seal design
ØAL ØMM
M A B T S
25 R901010141 R901010145 R901010147 R901010143 R901010146
40
28 R900851087 R900859445 R900859770 R900858841 R900861001
32 R900860274 R900860929 R900860939 R900860275 R900861003
50
36 R900849392 R900851515 R900860940 R900860277 R900861004
40 R900859509 R900851637 R900860941 R900860279 R900861006
63
45 R900847956 R900851638 R900859678 R900847855 R900861007
50 R900857129 R900856092 R900860943 R900860281 R900861009
80
56 R900850905 R900854718 R900851205 R900856180 R900861010
63 R900860283 R900856093 R900860945 R900860284 R900861012
100
70 R900853382 R900856094 R900860946 R900860285 R900861013
80 R900860287 R900860931 R900860950 R900860288 R900861015
125
90 R900857949 R900856095 R900855464 R900856102 R900861016
90 R900858281 R900860932 R900860951 R900860289 R900861017
140
100 R900853965 R900856096 R900860952 R900860290 R900849080
100 R900855683 R900860468 R900860953 R900860291 R900861018
160
110 R900851146 R900860933 R900860954 R900857536 R900861019
110 R900856497 R900860934 R900860955 R900852561 R900861020
180
125 R900848603 R900860935 R900860956 R900860292 R900861021
125 R900860294 R900860936 R900860957 R900860295 R900861022
200
140 R900856431 R900860937 R900860958 R900860293 R900861023
140 R900888100 R900888116 R900888140 R900888108 R900888132
220
160 R900888101 R900888117 R900888141 R900888109 R900888133
160 R900888102 R900888118 R900888142 R900888110 R900888134
250
180 R900888103 R900888119 R900888143 R900888111 R900888135
180 R900888104 R900888120 R900888144 R900888112 R900888136
280
200 R900888105 R900888121 R900888145 R900888113 R900888137
200 R900888106 R900888122 R900888146 R900888114 R900888138
320
220 R900888107 R900888123 R900888147 R900888115 R900888139
ØAL = Piston Ø

Seal kits
CGH2…XC – standard
ØAL ØMM
M A B T S
25 R901010159 R901010162 R901010170 R901010161 R901010169
40
28 R900867252 R900866747 R900867133 R900868889 R900868943
32 R900867254 R900866749 R900867135 R900868891 R900868945
50
36 R900864930 R900866750 R900867136 R900868892 R900868946
40 R900867261 R900866752 R900867138 R900868894 R900868948
63
45 R900867262 R900866753 R900867139 R900868895 R900868949
50 R900867264 R900866755 R900867141 R900868897 R900868951
80
56 R900867265 R900866756 R900867142 R900868898 R900868952
63 R900867267 R900866758 R900867144 R900868900 R900868954
100
70 R900867268 R900866759 R900867146 R900868901 R900868955
80 R900860730 R900866761 R900867148 R900868903 R900868956
125
90 R900867270 R900866762 R900867149 R900868904 R900868957
90 R900867271 R900866763 R900867150 R900868905 R900868958
140
100 R900867272 R900866764 R900867151 R900868906 R900868959
100 R900867273 R900866765 R900867152 R900868907 R900868960
160
110 R900867274 R900866766 R900867153 R900868908 R900868961
110 R900867275 R900866767 R900867154 R900868909 R900868962
180
125 R900867276 R900866768 R900867155 R900868910 R900868963
125 R900867277 R900866769 R900867156 R900868911 R900868964
200
140 R900867278 R900866770 R900867157 R900868912 R900868965
140 R900888020 R900888036 R900888060 R900888028 R900888052
220
160 R900888021 R900888037 R900888061 R900888029 R900888053
160 R900888022 R900888038 R900888062 R900888030 R900888054
250
180 R900888023 R900888039 R900888063 R900888031 R900888055
180 R900888024 R900888040 R900888064 R900888032 R900888056
280
200 R900888025 R900888041 R900888065 R900888033 R900888057
200 R900888026 R900888042 R900888066 R900888034 R900888058
320
220 R900888027 R900888043 R900888067 R900888035 R900888059
ØAL = Piston Ø

Seal kits
CDH2…XC – standard + additional option F

ØAL ØMM
M+F T+F S+F
25 R901010148 R901010149 R901010150
40
28 R900861025 R900861050 R900861100
32 R900861027 R900861052 R900861102
50
36 R900861028 R900861053 R900861103
40 R900861030 R900861055 R900861105
63
45 R900861031 R900861056 R900861106
50 R900861033 R900861058 R900861108
80
56 R900861034 R900861059 R900861109
63 R900861036 R900861061 R900861114
100
70 R900861037 R900861062 R900861115
80 R900861039 R900861064 R900861120
125
90 R900861040 R900861065 R900861122
90 R900861041 R900861066 R900861124
140
100 R900861042 R900861067 R900861126
100 R900861043 R900861068 R900861128
160
110 R900861044 R900861069 R900861130
110 R900861045 R900861070 R900861133
180
125 R900861046 R900861071 R900861135
125 R900861047 R900861072 R900861142
200
140 R900861048 R900861073 R900861143
CGH2…XC – standard + additional option F

ØAL ØMM
M+F T+F S+F
25 R901010151 R901010154 R901010156

40
28 R900868999 R900869026 R900869093
32 R900869001 R900869028 R900869095
50
36 R900869002 R900869029 R900869096
40 R900869004 R900869031 R900869098
63
45 R900869005 R900869032 R900869099
50 R900869007 R900869034 R900869101
80
56 R900869008 R900869035 R900869102
63 R900869012 R900869037 R900869104
100
70 R900869013 R900869038 R900869105
80 R900869015 R900869040 R900869107
125
90 R900869016 R900869041 R900869108
90 R900869017 R900869042 R900869109
140
100 R900869018 R900869043 R900869110
100 R900869019 R900869044 R900869111
160
110 R900869020 R900869045 R900869112
110 R900869021 R900869046 R900869113
180
125 R900869022 R900869047 R900869114
125 R900869023 R900869048 R900869115
200
140 R900869024 R900869049 R900869116
ØAL = Piston Ø ØMM = Piston rod Ø

Seal kits 2)
CSH2…XE
ØAL ØMM
M T S
40 28 R900861025 R900861050 R900861100
32 R900861027 R900861052 R900861102
50
36 R900861028 R900861053 R900861103
40 R900861030 R900861055 R900861105
63
45 R900861031 R900861056 R900861106
50 R900861033 R900861058 R900861108
80
56 R900861034 R900861059 R900861109
63 R900861036 R900861061 R900861114
100
70 R900861037 R900861062 R900861115
80 R900861039 R900861064 R900861120
125
90 R900861040 R900861065 R900861122
90 R900861041 R900861066 R900861124
140
100 R900861042 R900861067 R900861126
100 R900861043 R900861068 R900861128
160
110 R900861044 R900861069 R900861130
110 R900861045 R900861070 R900861133
180
125 R900861046 R900861071 R900861135
125 R900861047 R900861072 R900861142
200
140 R900861048 R900861073 R900861143
140 R900888100 R900888108 R900888116
220
160 R900888101 R900888109 R900888117
160 R900888102 R900888110 R900888118
250
180 R900888103 R900888111 R900888119
180 R900888104 R900888112 R900888120
280
200 R900888105 R900888113 R900888121
200 R900888106 R900888114 R900888122
320
220 R900888107 R900888115 R900888123
Only for position measurement system

ØAL
M, T S
40 R900885935 R900885937
50 R900894958 R900894979
63 R900894959 R900894980
80 R900894960 R900894981
100 R900894961 R900894982
125 R900894962 R900894983
140 R900894963 R900894985
160 R900894964 R900894986
180 R900894973 R900894987
200 R900894974 R900894988
220 R900894975 R900894989
250 R900894976 R900894991
ØAL = Piston Ø
280 R900894977 R900894993
320 R900894978 R900894994 2) Seal kits for position measurement system separate material no.
Tightening torques
Screws: Head and base (item 1 and 2)

1 2
Series Piston Ø Screw Quantity Quality class Tightening torque

CDH2…XC / CGH2…XC / CSH2…XE 40 M8 4 10.9 23 Nm
Screws: Seal cover (item 3)

3
Only with seal design "A" and "B"

Series Piston Ø Piston rod Ø Screw Quantity Quality class Tightening torque
100
CDH2…XC / CGH2…XC 160 M10 16 10.9 60 Nm
110
110
CDH2…XC / CGH2…XC 180 M12 16 10.9 80 Nm
125
125
CDH2…XC / CGH2…XC 200 M12 16 10.9 90 Nm
140
140 16
CDH2…XC / CGH2…XC 220 M12 10.9 90 Nm
160 24
160
CDH2…XC / CGH2…XC 250 M12 24 10.9 90 Nm
180
180
CDH2…XC / CGH2…XC 280 M12 24 10.9 90 Nm
200
200 M12 24 90 Nm
CDH2…XC / CGH2…XC 320 10.9
220 M16 16 230 Nm

Spare parts: Series CDH2…XC:

Piston rod Piston

"M" "S / T" "M / T / S"
"A / B" "A / B"
10
12 16
14
11 17
1 Head 6 Damping bush 11 Base MP5 17 Foot MS2

2 Base 7 Flange 12 Round flange MF3 18 Seal kit:
3 Pipe 8 Socket 14 Round flange MF4 ▶▶ Wiper
4 Piston rod 9 Socket 15 Bleeding ▶▶ Rod seal
10 Base MP3 16 Trunnion MT4 ▶▶ Piston seal
5 Piston
▶▶ Seal ring
▶▶ Guide ring

Spare parts: Series CGH2…XC:

Piston rod Piston

"M" "S / T" "M / T / S "
"A / B" "A / B"
16 17
12
1 Head 8 Socket 18 Seal kit:

3 Pipe 12 Round flange MF3 ▶▶ Wiper
4 Piston rod 15 Bleeding ▶▶ Rod seal
16 Trunnion MT4 ▶▶ Piston seal
5 Piston
▶▶ Seal ring
6 Damping bush 17 Foot MS2
▶▶ Guide ring
7 Flange

Spare parts: Series CSH2…XE: MF3, MF4, MT4 and MS2

Piston rod Piston

"M" "S / T" "M / T / S"
14 16 17
12
1 Head 7 Flange 16 Trunnion MT4 19 Insulating socket

2 Base 8 Socket 17 Foot MS2 20 Solenoid
3 Pipe 9 Socket 18 Seal kit: 21 Hexagon socket head
4 Piston rod 12 Round flange MF3 ▶▶ Wiper cap screws
5 Piston 14 Round flange MF4 ▶▶ Rod seal 22 Position transducer
6 Damping bush 15 Bleeding ▶▶ Piston seal 23 Protective pipe
▶▶ Seal ring 24 Seal
▶▶ Guide ring

Cylinder weight
Piston Piston rod CD/CS cylinder per 100 mm CG cylinder per 100 mm
with 0 mm stroke length stroke length with 0 mm stroke length stroke length
ØAL ØMM MP3 1) MF3 MT4 MS2 MF3 MT4 MS2
MP5 1) MF4
mm mm kg kg kg kg kg kg kg kg kg
25 7 9 9 9 0.9 10 10 10 1.3
40
28 7 9 9 9 1.0 10 10 10 1.5
32 12 14 13 13 1.3 16 16 16 1.9
50
36 12 14 13 14 1.5 16 16 16 2.3
40 20 21 21 21 2.3 25 25 25 3.3
63
45 20 21 21 21 2.6 25 25 25 3.8
50 32 35 34 35 3.2 41 40 41 4.7
80
56 32 35 34 36 3.6 41 40 42 5.5
63 51 54 54 55 5.2 63 63 64 7.6
100
70 51 55 54 56 5.7 64 64 65 8.8
80 95 96 99 98 8.2 113 115 114 12.1
125
90 96 97 100 99 9.2 115 117 116 14.2
90 131 132 136 137 10.7 155 158 159 15.7
140
100 132 133 137 138 11.9 156 160 161 18.1
100 185 184 197 206 12.6 217 231 239 18.8
160
110 186 186 199 207 13.9 220 233 242 21.4
110 255 253 264 274 14.7 294 305 314 22.1
180
125 258 256 267 277 16.8 300 311 320 26.5
125 349 332 350 363 19.0 359 377 389 28.6
200
140 352 335 353 366 21.5 365 383 396 33.5
140 27.1 39.1
220 527 512 546 518 604 638 610
160 30.9 46.7
160 32.7 48.5
250 673 640 677 650 761 798 772
180 36.9 56.9
180 44.2 64.2
280 976 966 1020 918 1130 1183 1081
200 48.8 73.4
200 55.2 79.8
320 1251 1172 1223 1174 1354 1405 1356
220 60.4 90.2
ØAL = Piston Ø
1) Weight without position measurement system

Notes

Notes
Bosch Rexroth AG © All rights reserved to Bosch Rexroth AG, also regarding any disposal,

Hydraulics exploitation, reproduction, editing, distribution, as well as in the event
Zum Eisengießer 1 of applications for industrial property rights.The data specified above only serve
97816 Lohr am Main, Germany to describe the product. No statements concerning a certain condition or
Phone +49 (0) 93 52 / 18-0 suitability for a certain application can be derived from our information. The
documentation@boschrexroth.de information given does not release the user from the obligation of own
www.boschrexroth.de judgment and verification.
It must be remembered that our products are subject to a natural process
of wear and aging.

Hydraulic Cylinder For Potentially Explosive Areas: Bosch Rexroth AG, RE 17335-X, Edition: 2019-04

Uploaded by

Copyright:

Available Formats

Hydraulic Cylinder For Potentially Explosive Areas: Bosch Rexroth AG, RE 17335-X, Edition: 2019-04

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hydraulic Cylinder For Potentially Explosive Areas: Bosch Rexroth AG, RE 17335-X, Edition: 2019-04

Uploaded by

Copyright:

Available Formats

Hydraulic cylinder for

potentially explosive areas

▶▶ Standards: DIN 24333, ISO 6022 Features1

Bosch Rexroth AG, RE 17335-X, edition: 2019-04

Ordering code: Series CDH2…XC

Foot mounting MS2 18)

04 Piston Ø (ØAL) 40 ... 320 mm ...

05 Piston rod Ø (ØMM) 25 ... 220 mm ...

06 Stroke length in mm 3) ...

Protection class for ATEX version

08 Component series 30 … 39 (30 … 39: unchanged installation and connection dimensions) 3X

Line connection / version

Flange connection according to ISO 6162-2 tab. 2 type 1 (≙ SAE 6000 PSI) D 4; 9)

Flange connection according to ISO 6164 tab. 1 K 1; 4)

Flange connection according to ISO 6164 tab. 2 H 4)

Line connection / position at head

Line connection / position at base

Piston rod design

Nickel-plated and hard chromium-plated N 24)

Piston rod end

Bosch Rexroth AG, RE 17335-X, edition: 2019-04

Ordering code: Series CDH2…XC

End position cushioning

Fields for additional options

18 Additional guide rings F 10)

Without additional guide rings W

19 Measuring coupling, on both sides A

20 Flanged grease nipple B

21 Specify the piston rod extension LY in the plain text in mm Y

Without additional options: With additional options:

1) Only piston Ø 40 to 200 mm 18) Not standardized

RE 17335-X, edition: 2019-04, Bosch Rexroth AG

Ordering code: Series CGH2…XC

Foot mounting MS2

04 Piston Ø (ØAL) 40 ... 320 mm ...

05 Piston rod Ø (ØMM) 25 ... 220 mm ...

06 Stroke length in mm 3) ...

Protection class for ATEX version

08 Component series 30 … 39 (30 … 39: unchanged installation and connection dimensions) 3X

Line connection / version

Flange connection according to ISO 6162-2 tab. 2 type 1 (≙ SAE 6000 PSI) D 9)

Flange connection according to ISO 6164 tab. 1 K 1)

Flange connection according to ISO 6164 tab. 2 H

Line connection / position at head

Line connection / position at base

Piston rod design

Piston rod end

End position cushioning

Bosch Rexroth AG, RE 17335-X, edition: 2019-04

Ordering code: Series CGH2…XC

Fields for additional options

18 Additional guide rings F 10)

Without additional guide rings W

19 Measuring coupling, on both sides A

20 Flanged grease nipple B

21 Specify the piston rod extension LY in the plain text in mm Y 16)

Without piston rod extension W

Without additional options: With additional options:

1) Only piston Ø 40 to 200 mm 18) Not standardized

▶▶ Standards: DIN 24333, ISO 6022 Features1