Daimler Chrysler Transmission

Trucks • Transmission
Telligent automatic transmission

in ACTROS and ATEGO
Specialist training
As at 10/03
Trucks • Transmission <> Telligent

automatic transmission in ACTROS and
ATEGO <<>> S i li t t i i
This document is intended solely for use in training and is not subject to regular updating.
Printed in Germany Note:

ã 2003 Copyright DaimlerChrysler AG The term »employees« does not imply any preference
of gender and incorporated male and refers to maler
Publisher: Global Training and female employees alike.
This document with all its sections is protected under the laws of copyright. Its use for any purpose whatsoever
requires the prior written consent of DaimlerChrysler AG. This applies in particular to its reproduction, distribution,
modification, translation, recording on microfilm or storage and/or processing in electronic systems, including
databases and on-line services.
st
1511 5555 02 - 1 edition 10.03 124 As at 10/03
Content 29.10.2003
Title Page
Welcome ..................................................................................................................................................................................................................................................1
Training Course Description Code NGAS - MA253..................................................................................................................................................................................3
Overview of shifting systems for ACTROS, AXOR and ATEGO.................................................................................................................................................................4
KontAct network diagram ACTROS models 930 - 934 ............................................................................................................................................................................6
KontAct network diagram for ACTROS models 930-934; exercise .........................................................................................................................................................8
EAS II (Code GE 2) - evolution of control units ........................................................................................................................................................................................9
EAS II - (Code GE2), function diagram ...................................................................................................................................................................................................10
EAS II (Code GE 2), function ..................................................................................................................................................................................................................12
EAS II - (Code GE2), function diagram; exercise....................................................................................................................................................................................13
Power train networking with EAS II, ACTROS models 930-934; exercise .............................................................................................................................................15
Information exchange on gear shifting EAS ACTROS, models 930-934; exercise ................................................................................................................................17
EAS II - (Code GE2), information exchange and actual values, exercise ...............................................................................................................................................20
EAS II - (Code GE2), components ..........................................................................................................................................................................................................22
EAS II - (Code GE2), control circuit ........................................................................................................................................................................................................25
EAS II - (Code GE2), clutch actuator adjustment, exercise ...................................................................................................................................................................27
EAS II - (Code GE2), clutch actuator - clutch control; exercise .............................................................................................................................................................28
EAS II - (Code GE2), versions, exercise..................................................................................................................................................................................................30
EAS II - (Code GE2), teach-in process; exercise ....................................................................................................................................................................................31
10/03 Trucks • Transmission <> Telligent automatic transmission in ACTROS and ATEGO <<>> Specialist training
TR Content I 1
EAS II - (Code GE2), teach-in process and teach-in faults; exercise......................................................................................................................................................32
EAS II - (Code GE2), clutch characteristics............................................................................................................................................................................................34
EAS II - (Code GE2), backup mode special features ..............................................................................................................................................................................36
EAS II - (Code GE2), drive control actual values and GS II, exercise .....................................................................................................................................................37
Foot throttle actuator, standard quantity; exercise...............................................................................................................................................................................39
Foot throttle actuator, onboard teach-in, ACTROS models 930 - 934 ..................................................................................................................................................40
Troubleshooting chart for GS II and EAS II, TIPS procedure and application ........................................................................................................................................41
Carrying out diagnosis with the layer model .........................................................................................................................................................................................43
EAS II - (Code GE2), practical 1; exercise ..............................................................................................................................................................................................50
AGS (Code GE1), functional description ................................................................................................................................................................................................58
AGS (Code GE1), installation survey......................................................................................................................................................................................................59
Design and features of the G60/85 transmission; exercise .................................................................................................................................................................60
G60/85 transmission transverse shift gate; exercise ...........................................................................................................................................................................63
ATEGO power train networking control units - AGS (Code GE1), exercise............................................................................................................................................64
ATEGO power train networking engine management - AGS (Code GE1); exercise ...............................................................................................................................65
Power train networking - AGS (Code GE1), ATEGO ...............................................................................................................................................................................67
Power train networking - AGS (Code GE1), ATEGO, exercise ................................................................................................................................................................69
AGS (Code GE1), sensor unit operation.................................................................................................................................................................................................71
AGS (Code GE1), sensor unit operation; exercise .................................................................................................................................................................................72
AGS (Code GE1), location of the AGS components on the transmission and their task.......................................................................................................................75
TR Content I 2
AGS (Code GE1), location of the AGS components on the transmission and their task; exercise........................................................................................................81
AGS (Code GE1), assignment and actuation of the solenoid valves; exercise ......................................................................................................................................83
AGS (Code GE1), transmission shift states, exercise ............................................................................................................................................................................86
AGS (Code GE1), sensor analysis, teach-in process and shifting procedure.........................................................................................................................................91
AGS (Code GE1), teach-in process and teach-in faults; exercise ..........................................................................................................................................................93
AGS (Code GE1), clutch sensing............................................................................................................................................................................................................97
AGS (Code GE1), FR and AGS actual values; exercise...........................................................................................................................................................................98
AGS (Code GE1), AGS clutch balancing.............................................................................................................................................................................................. 100
AGS (Code GE1), instructions for testing and repair work ................................................................................................................................................................. 102
AGS (Code GE1), emergency operation characteristics ..................................................................................................................................................................... 103
Transmission diagnosis, practical example template ......................................................................................................................................................................... 104
AGS (Code GE1), practical 1; exercise................................................................................................................................................................................................ 108
TR Content I 3
TR Content I 4
Welcome 29.10.2003
Welcome to the NGAS training course. As the training course progresses, it

will become evident how this subject is presented. While it was relatively easy
to have an overview of the shift devices used with the LK and SK, one or two
things have changed since the launch of the ACTROS, ATEGO and AXOR. The first
challenge has no doubt been dealing with the "networking" of the systems.
This will be just one of the hurdles you will have to overcome in the course of
the NGAS training. It will soon become evident that, even with a good
foundational training in electrics, you will only be able to do a proportion of
the tasks set. The other tasks require a good understanding of transmission
mechanics, wiring and different hydraulic systems.
If you have some experience and understanding in the areas of mechanics,

hydraulics and electrics, this will be of great benefit and you will be able to
follow the training course easily. If not, then you have quite some ground to
cover, but we will be happy to help and support you in your efforts.
This is because those who understand the systems are also quick to make a
confident diagnosis. While diagnostic aids, such as DAS and WIS, can
certainly help you in your work, they will rarely actually make the decision for
you as to what ultimately needs repairing.
During the training course you will work with all the named diagnostic aids so
that you will be in a better position afterwards to make a diagnosis on the
shift devices "at home", in your workshop.
N26.10-2067-00
Welcome 1
Training sequence
Day 1 Welcome
c Day 2 Design and function of the Telligent automatic
transmission – AGS gearshift system in the ATEGO c o
Overview of gearshift systems and types of gearshift
system c o Networking of the Telligent automatic transmission –
AGS gearshift system in the ATEGO h c
Design and function of the Telligent automatic
transmission II – EAS II gearshift system in the c o Teach-in processes of the Telligent automatic
transmission – AGS gearshift system in the ATEGO c o
ACTROS
Networking of the Telligent automatic transmission II

– EAS II gearshift system in the ACTROS c o DAS actual values of the AGS system and drive
control c o
Teach-in processes of the Telligent automatic
transmission II – EAS II gearshift system in the
c o Practical work on the ATEGO
h o
ACTROS
DAS actual values of the GS II system and drive

control c o Troubleshooting aids based on customer complaints
o
Practical work on the ACTROS
h o Presentation and feedback in plenary session
c o
Troubleshooting aids based on customer complaints
o Final test
o
Presentation and feedback in plenary session
c o Feedback and close of training session
o
Feedback from day 1
o
Welcome 2
Training Course Description Code NGAS - MA253 29.10.2003
Training course description ACTROS, ATEGO — Telligent® automatic transmission (EAS, AGS) • Specialist training
Target group Mechanics, electricians
Requirements The course participants are required to have passed the final test of the NGGG training or have worked through
the preliminary training and passed the initial test. (The knowledge required for this can be acquired from the
CBTs "Telligent gearshift system Parts 1 – 4", "Telligent automatic transmission Parts 1 – 2" and "Wiring
diagrams Parts 1 + 3").
Performance level 3
Methodology 50% theory, 50% practical
Duration 2 days DCVD, 2-3 days Export
Objectives The participant can:
· independently prepare a diagnosis on the Telligent® automatic transmission (ACTROS - EAS; ATEGO - AGS)
· perform testing, adjusting and repair work
Contents · Design and function of the Telligent® automatic transmission vehicle networking
· Drive control on pneumatic (EAS) and hydraulic (AGS) shifting systems
· Diagnosis using current diagnosis systems and fault diagnosis based on case examples
· Carrying out the necessary teach-in processes
TR Training Course Description Code NGAS - MA253 3
Overview of shifting systems for ACTROS, AXOR and ATEGO 11.02.03
Since the launch of the ATEGO, AXOR and ACTROS, various other shifting systems have been introduced in addition to the mechanical gearshift system, the MPS
and the EPS, already familiar to us from the SK.
{0>Die verschiedenen Schaltungsarten werden über Verkaufscode dem jeweiligen Getriebetyp und Fahrzeug zugesteuert.<}100{>The various shifting types are
assigned to the respective transmission type and vehicle by way of the sales code.
The respective sales code can be found on the data card.
While no completely new types of gearshift system were introduced with the refinement of the ACTROS model (MPII) in the spring of 2003, existing systems were
nevertheless revised. As a result new sales codes have been issued for better differentiation.
The ATEGO model series is also earmarked for various innovations in 2003. These are also listed below.
The list differentiates between the following shifting systems in the current generation of vehicles:
ACTROS, AXOR, ATEGO Changes to ACTROS models 930 - 934
Sales code GS 1:
· Mechanical shift - MS
· Mechanical-pneumatic shift – MPS
· Mechanical-pneumatic shift with
pneumatic shifting aid - MPS with PSH
Sales code GS 3:
· Hydraulic shift - HS
· Hydraulic-pneumatic shift - HPS
· Hydraulic-pneumatic shift with shift force assist – HPS with SKU
Sales code GS 2: Sales code GS 7:
· Telligent gearshift system – EPS II · Telligent gearshift system II (GSII)
Sales code GE 1: Sales code GE 2:
· Telligent automatic transmission – EAS · Telligent automatic transmission II – EAS II
· Telligent automatic transmission -- AGS
TR Overview of shifting systems for ACTROS, AXOR and ATEGO 4
Gearshift system types arranged according to vehicles and transmissions
Mechanical shift Hydraulic shift Telligent Telligent

gearshift syst. aut. transmission
GS 1 GS 3 GS 2 GS 7 GE 1 GE 2
MS MPS MPS with HS HPS HPS with GS GS II EAS/AGS EAS II
PSH SKU
ATEGO ZF S 5-42 GF 1 !
G 56 - 6 GC 4 ! 10/04
(up to 15t) G 60 - 6 GC 5 ! AGS
G 85 - 6 GC 6 ! AGS
G 100 - 12 GC 7 !
ATEGO G 85 - 6 GC 6 ! AGS
(as of 18t) G 100 - 12 GC 7 !
G 131 - 9 GT 1 10/03
G 221 - 9 GD 5 !
G 211 - 16 GD 3 ! !
AXOR G 211 - 16 GD 3 !
G 221 - 9 GD 5 !
G 240 - 16 GC 2 ! !
ACTROS G 210 - 16 GC 3 ! ! ! ! EAS !
G 211 - 16 GD 3 ! ! ! EAS !
G 231 - 16 GH 6 ! ! ! EAS !
G 240 - 16 GC 2 ! ! ! ! EAS !
G 260 - 16 GC 1 ! ! ! ! EAS !
TR Overview of shifting systems for ACTROS, AXOR and ATEGO 5
KontAct network diagram ACTROS models 930 - 934 04.02.03
W00.19-1011-79
TR KontAct network diagram ACTROS models 930 - 934 6
1 Power train components A22 Control unit, parameterizable special module (PSM) K2 Battery disconnect switch
2 Brake components A64 Front module (FM) K Diag K-line diagnosis
3 Trailer and body components A65 Rear module (HM) K Emergency K-line, emergency running mode
4 Vehicle components CAN 1 Vehicle CAN P2 Instrument (INS)
5 Cab components CAN 2 Interior CAN P3 Modular tachograph (MTCO)
6 Frame components CAN 3 Frame CAN X11 15-pin trailer socket
7 Telematics / diagnosis CAN 4 Engine CAN X12 7-pin ABS trailer socket
22 Body electronics CAN 5 Transmission CAN X13 Diagnostic socket
CAN 6 Brake CAN X126 Telematics platform (FleetBoard)
A3 Control unit, drive control (FR) CAN 7 Trailer CAN (PSM) Z2 CAN star point, cab dash support, additional
A7 Base module (GM) CAN 8 Body CAN Z3 CAN star point, additional
A11 Control unit, brake control (BS) CAN 9 Telematics CAN
A16 Control unit, gear control (GS) CAN 10 Speedometer CAN
A20 Control unit, retarder control (RS) CAN 11 Trailer CAN (BS)
Note: For further information see GF 00.19-W-0002 MP "Extended vehicle network KontAct function"
TR KontAct network diagram ACTROS models 930 - 934 7
KontAct network diagram for ACTROS models 930-934; exercise 12.02.03
This exercise is concerned with the new network in the ACTROS. Use the new network diagram to work through the following tasks.
Task m Enter the CAN BUS designations.
CAN 3 Frame CAN BUS CAN 10 Tachograph CAN BUS

CAN 1 Vehicle CAN BUS CAN 11 Trailer CAN (BS)
CAN 5 Transmission CAN BUS CAN 7 Trailer CAN (PSM)
CAN 6 Brakes CAN BUS CAN 9 Telematics CAN BUS
CAN 4 Engine CAN BUS CAN 8 Body CAN
CAN 2 Interior CAN BUS
Task m Which control units are part of the vehicle CAN BUS?
- Base module (A7), control unit for drive control (A3), control unit for brake control (A11)
- Control unit for retarder control (A20), Parameterizable special module control unit (A22)
- Instrument (P2), CAN star point cab dash support, additional (Z2)
TR KontAct network diagram for ACTROS models 930-934; exercise 8
EAS II (Code GE 2) - evolution of control units 29.10.2003
ACTROS, models 950 -954

Control units
ACTROS, models 930 - 934

Software modules
ACTROS, models 930 - 934

Control units
GT26_00_0014
TR EAS II (Code GE 2) - evolution of control units 9
EAS II - (Code GE2), function diagram 29.10.2003
GT_26_21_0002 (W26.21-1009-79)
TR EAS II - (Code GE2), function diagram 10
1 Gate shift cylinder B2 Clutch travel sensor S144 Button group on left of multifunction steering wheel
2 Range shift cylinder B3 Countershaft speed sensor S145 Button group on right of multifunction steering wheel
3 Gear cylindrical actuator B17 Speed sensor
4 Splitter shift cylinder B57 Transmission output speed sensor Y29 Solenoid valve, split 1 (MS1)
5 Clutch actuator B60 Gear sensor (SGG) Y30 Solenoid valve, split 2 (MS2)
6 Multifunction steering wheel B61 Gate sensor (SGE) Y31 Solenoid valve, range 1 (MR1)
B62 Splitter sensor (SSP) Y32 Solenoid valve, range 2 (MR2)
B63 Range sensor (SRA) Y33 Solenoid valve, gate 1 (MG1)
Y34 Solenoid valve, gate 2 (MG2)
A3 Control unit for drive control (FR) with integrated CAN1 Vehicle CAN Y35 Uneven gears air admission solenoid valve (MUB)
drive control (FR) software module
A6 Control unit for engine control (MR) CAN2 Interior CAN (redundant) Y36 Even gears air admission solenoid valve (MGB)
A7 Base module (GM) CAN4 Engine CAN Y37 Uneven gears air release solenoid valve (MUE)
A15 Sensor unit for gear control (GS) CAN5 Transmission CAN Y38 Even gears air release solenoid valve (MUE)
A16 Control unit for gear control (GS) with integrated
gear control (GS) software module
A90 Gate module KNot K-line emergency running mode
A91 Range module P2 Instrument (INS)
A92 Gear module
TR EAS II - (Code GE2), function diagram 11
EAS II (Code GE 2), function 29.10.2003
General points:
Based on the gear control II (GS II) shifting system, the Telligent automatic transmission II (EAS II) is a special design with automated clutch.
The design of the Telligent automatic transmission II (EAS II) based on the gear control II (GS II) has been substantially simplified:
The entire clutch hydraulic system used in the first-generation EAS has been replaced by an electropneumatic clutch actuator. This clutch actuator directly
operates the mechanical clutch system.
The old EAS, AG and KS control units are still there but only as virtual control units. The AG is integrated as a drive control software module. The KS control
unit is integrated in the GS control unit as a clutch control software module.
This dispenses with the need for hydraulic lines and maintenance work.
Only the electrical and pneumatic lines are still connected to the clutch actuator.
With the fold-out emergency clutch pedal no longer required, only the accelerator and brake pedals remain.
The option of activating manual or automatic shift mode via a selector switch on the gear control sensor unit has been retained.
Ride comfort has been improved, e.g., the system changes independently from the normal drive mode to a maneuver mode if required. This makes
maneuvering considerably easier.
The Telligent automatic transmission II (EAS II) can be operated in two modes:
· Automatic operation
· Manual operation
The electronic systems for the transmission and the on-board related functions are entirely separate.
Information is exchanged between the electronic systems in the form of CAN messages via the CAN connections
Vehicle CAN (CAN 1),
Interior CAN (CAN 2),
Engine CAN (CAN 4)
Transmission CAN (CAN 5)
and via the
· K line emergency running mode (KNot), in backup drive mode
TR EAS II (Code GE 2), function 12
EAS II - (Code GE2), function diagram; exercise 29.10.2003
Task
Using the drawing opposite allocate the following components to the
corresponding terminals, fuses and relays!
Component Terminal Fuse Relay
P2 30 F 17 ----
15 F 30 K4
A3 30 F 14 ----
15 F 28 K4
A16 30 F4 ----
30 F 12 ----
15 F 20 K3
A 15 15 F 28 K4
N26.20-2010-12
TR EAS II - (Code GE2), function diagram; exercise 13
Task m Indicate the correct sequence of the signal path during a gear change on the TelligentÒ automatic
transmission in "Manual mode".
Note:
For further information, see GF 26.20-W-0001 MP "Gear control (GS) function" and circuit diagram.
3 GS control unit
2 FR control unit
1 Sensor unit
6 GS control unit
5 Gear, gate, range and splitter sensors
4 Gear, gate, range and splitter solenoid valves
Task m The TelligentÒ automatic transmission communicates with other components and systems in different
ways. Complete the table.
Component Designation Communication / Connection Designation Component

Sensor unit A15 Electrical line A3 FR control unit
FR control unit A3 CAN 5 (Transmission CAN) A16 GS control unit
GS control unit A16 Electrical line Connected components
Instrument P2 KNot/CAN1/CAN5 A16 GS control unit
Instrument P2 CAN1 / CAN2 A7 Base module
Multifunction steering S144/S145 Electrical line A7 Base module
wheel
Modular tachograph P3 CAN 5 (Transmission CAN) A16 GS control unit
TR EAS II - (Code GE2), function diagram; exercise 14
Power train networking with EAS II, ACTROS models 930-934; exercise 02.06.03
ASIC HM
X13 B28 A68 A82 B5
A65
CAN 10 CAN 2 CAN 3
MTCO INS GM
B17 S144 S145
P3 P2 A7
CAN 1
Y44 B65 B66
RS PSM BS
A20 A22 A11 K
G2 S2 B1 CAN 5
FR GS
A3 A16
A42 S1 A15
CAN 4
MR FLA Y1 Y2
A6 A4
B10 B15 B16 B65 B111
B11 B12 B14 S10 S11 S166 Y6-13 M1
TM Antriebsstrang 1_D.ppt
TR Power train networking with EAS II, ACTROS models 930-934; exercise 15
Task m The diagram shows an all-wheel drive vehicle with retarder control (RS) and EAS II.
Name the missing components.
The following questions may help you to solve the problem.

· How is the clutch actuated?
· Have you also considered clutch sensing?
· Have you thought about all the components required for engaging a gear?
· How is the corresponding gear position determined?
· Have you taken the splitter gearshift system components into consideration?
· How is a driver command transmitted?
Note: Further information on the Telligent automatic transmission II can be found in WIS under
GF 26.21-W-0001 MP "Electronic drive control (EAS) operation".
TR Power train networking with EAS II, ACTROS models 930-934; exercise 16
Information exchange on gear shifting EAS ACTROS, models 930-934; exercise 29.10.2003
Operation Transmitter Receiver What is the reason and the purpose for the part action?
Evaluation of shift logic FR FR Evaluation of CAN messages (influencing variables)
Internal evaluation in the AGF software module
Select: open clutch FR GS CAN 5 (transmission CAN)
Reduce engine torque FR MR CAN 4

De-energized power train
Open clutch GS Y39.1/39.2 Energizing of corresponding solenoid valves
Gear can only be changed when clutch open
Perform gear change GS Corresponding Energizing of corresponding solenoid valves
solenoid valves
Adjust engine speed FR MR Change in unit pump actuation time and permanent brake actuation, levels 1+2
Reduction of clutch wear
Current gear position feedback B60, B61, B62, GS Evaluation of displacement value sensor, energizing of corresponding solenoid valves,
B63 determination of current gear
Display shifted gear GS INS CAN 5, CAN 1
Display of engaged gear
Close clutch GS Y39.3/39.4 Energizing of corresponding solenoid valves
Establishment of power train frictional connection
Increase engine torque FR MR CAN 4, change in unit pump actuation time
Adjustment of specified engine torque setting on FR
TR Information exchange on gear shifting EAS ACTROS, models 930-934; exercise 17
Task m You now know the gear change sequence involved in a gear change. Complete the table below by
determining the detailed information contained in the data exchanged between transmitter and
receiver. If possible, explain why the information is required.
Operation Transmitter Receiver Relevant information Reason

Evaluation of shift logic FR FR Internal data exchange on AGF software Evaluation of relevant CAN messages
module (influencing variables)
Select: open clutch FR GS Open clutch request Control of clutch actuator
Reduce engine torque FR MR CAN message (change engine speed and De-energizing of power train
engine torque)
Open clutch GS Y39.1/39.2 Energizing of clutch actuator solenoid valves, Open clutch,
clutch position, electronic pulse Clutch position feedback
Perform gear change GS Corresponding Electronic pulse
solenoid valves
Adjust engine speed MR, Y6-Y13 Change unit pump actuation time and engine Reduction of clutch wear
FR brake actuation
Current gear position B60, B61, B62, GS Position of sensors in gear, gate, splitter and Evaluation takes place in GS control unit
feedback B63 range cylinders
Display shifted gear GS INS Shifted gear Driver information
Close clutch GS Y39.3/39.4 Energizing of clutch actuator solenoid valves, Close clutch
clutch position, electronic pulse
Increase engine torque FR MR CAN message Adjust FR specified torque setting
Task m You now know the information exchange when shifting gear. But how can you still test the pieces of
information?
Complete the table below. Use the DAS simulation and the DAS to help you complete the
corresponding actual values in the respective fields.
Operation Transmitter Actual values Transmission Receiver Actual values

Evaluation of shift logic FR --- --- FR 113, 114
Select: open clutch FR 16, 82, 83, 86 --- GS 157, 287, 307
96, 100, 114, 117
Reduce engine torque FR 14, 15 --- MR 01, 02
Open clutch GS 039 --- Y39.1/Y39.2 221, 223
B2
Perform gear change GS 288-297 --- Corresponding ---
solenoid valves
Adjust engine speed MR 004, 006, 034 --- Y6-Y13 ---
Current gear position B60, B61, --- --- GS 35-39
feedback B62, B63
Display shifted gear GS 156 FR INS ---
Close clutch GS 287 --- Y39.1/Y39.2 ---

B2
Increase engine torque FR 14, 15 --- MR 004, 006
EAS II - (Code GE2), information exchange and actual values, exercise 29.10.2003
The control units are networked together by a

linear bus structure using the CAN bus network
between the electronic systems of the engine
control and the on-board systems (GS, INS, etc.).
A control unit receives a measured value from a B28 ASIC CAN 3
A68 A82
sensor, from which it generates a data telegram
and puts in on the data bus, where it is available X13 B17
MTCO CAN 10 INS CAN 2 GM HM
B5 S144 S145
P3 P2 A7 A65
to all the control units connected to the CAN bus.
CAN 1
Y44 B65 B66
The control electronics control and monitor the
RS PSM BS B2 B3 B57 B99
entire GS system gear change sequence. K
A20 A22 A11
The control electronics receive information from
the system's own sensors and switches (travel G2 S2 B1 B60 B61 B62 B63
sensors and speed sensors) and also via the CAN FR CAN 5 GS
interface of other vehicle systems. A3 A16
A42 S1 A15
Y29 Y30 Y31 Y32 Y33
The corresponding solenoid valves are actuated
CAN 4
for shifting the gears. Data are exchanged with Y1 Y2
Y34 Y35 Y36 Y37 Y38
other electronic circuits via the CAN interface.
MR FLA
The shifted and preselected gears and also the A6 A4 Y39.1 Y39.2 Y39.3 Y39.4
events and text messages are displayed to the B10 B15 B16 B65 B111
operator in the instrument.
Y6-13 M1 B11 B12 B14 S10 S11 S166
PPT
TR EAS II - (Code GE2), information exchange and actual values, exercise 20
Task m The diagram shows the GS electronic circuits and those components directly connected. The details
are based on the given vehicle, an Actros with Telligent automatic transmission and all-wheel function.
1. First complete the information exchanged and the direction of information between the relevant
components.
2. Secondly complete the actual value (IW) number that goes with the relevant information.
Use GF 26.20-W-0007MP.
Module IW Information Information IW Pin Com- Module

ponent
ç GS backup mode 308 P2
Y35 MUB 290 Actuation of uneven gear ç ç V signal 037 P3
Y37 MUE 291 Actuation of uneven gear ç ç Gate cylinder position 035 B61
A92 Y36 MGB 292 Actuation of uneven gear ç ç Split cylinder position B62
Y38 MGE 293 Actuation of even gear ç A16 ç Clutch position 039 B2
B60 036 Gear cylinder position è ç Transmission input speed 021 B3
Y29 MG1 294 Actuation of gate R ç GS ç Oil temperature B47
A90 Y30 MG2 295 Actuation of gate 3/4 ç ç Transmission output speed with 221 B99
transfer case
Y33 MS1 288 Actuation of splitter L/H è è Detection of direction of travel 281 B57
Y34 MS2 289 Actuation of splitter L/H è è Open clutch - rapid 298 MKUB1 A39.1
Y31 MR2 297 Actuation range high ç è Open clutch - slow 298 MKUB2 A39.2 A93
A91 Y32 MR1 296 Actuation range low ç è Close clutch - rapid 298 MKUE1 A39.3
B63 038 Range cylinder position è è Close clutch - slow 298 MKUE2 A39.4
TR EAS II - (Code GE2), information exchange and actual values, exercise 21
EAS II - (Code GE2), components 29.10.2003
Clutch actuator
The tasks of the clutch actuator are as follows:
· To convert the electrical control signals in the pneumatic control of the actuator cylinder
· To record clutch travel and provide an electrical signal
· To operate the mechanical clutch system
The following components are integrated in the clutch actuator:
· Solenoid valves: Clutch aeration 1, Clutch aeration 2,

Clutch bleeding 1, Clutch bleeding 2
· Clutch travel sensor (B2)
· Actuator cylinder
W25.20-1018-11 (GT_25_20_0010)
N25.20-2064-01 N25.20-2063-01
TR EAS II - (Code GE2), components 22
The clutch actuator directly operates the
mechanical clutch system.
Each of the clutch positions can be moved to and

retained by means of the four solenoid valves.
This basic principle applies:
Cylinder extended ® Clutch open

Cylinder retracted ® Clutch closed
The clutch travel sensor (B2) records the current

position of the clutch actuator.
Key:
MKUB1 Solenoid valve, aerate clutch with throttle

MKUB 2 Solenoid valve, aerate clutch
MKUE 1 Solenoid valve, bleed clutch with throttle
MKUE 2 Solenoid valve, bleed clutch
GT25_00_0001
The four solenoid valves are necessary to properly control the inward and outward flow of compressed air used to move the cylinder.
MKUB2 and MKUE2 have a large air passage and are used to roughly regulate the clutch travel.
MKUB1 and MKUE1 work with a smaller flow area and are used for fine adaptation and very precise positioning during clutch actuation.
Transmission output speed sensor (B57, B99)
The task of the transmission output speed sensor

is as follows:
· To record the transmission output rpm

DZ1/DZ2
The additional recording of the transmission

output rpm is needed to detect the direction of
rotation.
The transmission output speed sensor (B57) is

installed in all vehicles with Telligent automatic
transmission II.
Vehicles with Telligent automatic transmission II

require direct recording of the transmission
output rpm.
This is because the speed sensor (B17) has been

moved to the transfer case output.
For this reason the transmission output speed

sensor (B99) is only additionally used on vehicles
with Telligent automatic transmission II and all-
wheel drive.
W26.19-1026-06 (GT_26_20_0019)
EAS II - (Code GE2), control circuit 29.10.2003
The basic functions and gear change sequences of the Telligent automatic transmission II can be represented as a simple control circuit.
The Telligent automatic transmisssion II control circuit consists of the system being controlled (transmission, clutch) and the FR control unit (A3), comprising
automatic gear selection (AG software modules) and clutch control (KR software modules) based on the gear control (GS) and clutch operation (KB) (both
software modules in the GSII control unit, A16).
The GS sensor unit (A15) provides the preselected gear in the form of a confirmation to the FR control unit (A3).
Vehicle-specific data are processed in the drive control (FR) software module in the FR control unit (A3). All the shift-related data are recorded and processed in
the automatic gear selection (AG) software module, tasked with the ongoing calculation of possible target gears which correspond to the shift strategy. The
clutch control (KR) records and processes all the data relating to the clutch control. The clutch operation (KB) in the GS II control unit (A16) converts these
entries accordingly.
This information regarding the targeted gear to be shifted and regarding the clutch control is relayed to the GS control unit (A16) via the transmission CAN.
The entries for the targeted gear cannot be overwritten by the gear control II (A16). The gear control can only refuse to perform a gearshift in emergency
situations (changed conditions suddenly brought about by influencing factors).
The gear control (GS) and clutch operation (KB) software modules convert the commands in the GS control unit (A16) accordingly and control the correct
solenoid valves to open and close the clutch and shift the targeted gear.
The controlled system consists of the clutch and the transmission. The GS control unit compares the specified values (learned values) with the actual conditions
and actual values.
The actual values represent the actual clutch and transmission operating conditions that are recorded via the different indicators and sensors. In the event that
the comparison shows a difference between the actual values and the learned values, a shift abort might be introduced, for example, depending on the situation,
or a corresponding event message displayed on the driver information system (FIS).
The learned values are entered in the GS II system during the "minor" and "major" teach-in processes. The response of the clutch operation is affected by the
clutch characteristics in the FR control unit (A3).
If a gear change is to be completed in drive status, the gear to be shifted (targeted gear) is determined on the basis of several variables.
TR EAS II - (Code GE2), control circuit 25
Task 1 m Complete the control circuit of the Telligent automatic transmission II in the ACTROS models 930-934
by entering the corresponding terms printed in bold opposite according to the description.
Gear selection
Factors influencing gear selection A6
CAN 4
A3
Actual gear CAN 1 FR
Current operating conditions 1 2
Preset gear
A 15 3 4
Actuation of solenoid valves
Calculation of gear differential CAN 5
A16
GS
Control device 3 5
1 FR software module
2 AGF software module
3 Evaluation / comparator 6 7
4 KS software module
5 GS software module
6 Emergency computer
7 KR software module
A3 Control unit for drive control Transmission
A6 Control unit for engine control
A15 GS sensor unit Controlled system
A16 Control unit for gear control
CAN1 Vehicle CAN
CAN2 Interior CAN Sensors Cylinder
CAN4 Engine CAN
CAN5 Transmission CAN
Powerpoint Regelkreis GSII.ppt
TR EAS II - (Code GE2), control circuit 26
EAS II - (Code GE2), clutch actuator adjustment, exercise 29.10.2003
In order to simplify the control system and, in so doing, to increase the positioning rate, the clutch actuator plunger tolerances must be kept as low as possible.
Before installing the clutch actuator, the actuator plunger has to be properly adjusted.
Task m When is it necessary to readjust the clutch actuator plunger?

For further information see WIS AR25.20-W-3000A
- When replacing the clutch or clutch actuator plunger, when working on the clutch operation
Task m How is the clutch actuator plunger adjusted?

For further information see WIS AR25.20-W-3000-01A
- By mounting a special tool on the transmission housing
- By adapting the length of the plunger in line with the gauge
W25.40-1076-01 W25.40-1077-01
TR EAS II - (Code GE2), clutch actuator adjustment, exercise 27
EAS II - (Code GE2), clutch actuator - clutch control; exercise 05.05.03
Clutch actuator solenoid valves
Task m The design and function of the clutch actuator are familiar. Which solenoid valves of the clutch
actuator must be energized in order to elicit the preselected clutch response? Complete the table.
Clutch response MKUB1 MKUB2 MKUE1 MKUE2
Open clutch slowly X
Open clutch rapidly X X
Close clutch slowly X
Close clutch rapidly X X
Hold clutch around drag point X X
Task m What response is elicited if one of the clutch actuator solenoid valves fails or if the clutch actuator
plunger is not correctly adjusted? Complete the table.
Failure of solenoid valve or plunger adjustment Clutch response
Sluggish Delayed Rough Sudden No longer No longer Failure Comfort
closes opens loss
MKUB1 X X X
MKUB2 X X X
MKUE1 X X X
MKUE2 X X X
MKUB1+2 X X
MKUE1+2 X X
Adjustment dimension too low X
Adjustment dimension too great X
TR EAS II - (Code GE2), clutch actuator - clutch control; exercise 28
Clutch actuator design
MKUB1 Solenoid valve, aerate clutch with throttle

MKUB2 Solenoid valve, aerate clutch
MKUE1 Solenoid valve, bleed clutch with throttle
MKUE2 Solenoid valve, bleed clutch
GT25_00_0001
TR EAS II - (Code GE2), clutch actuator - clutch control; exercise 29
EAS II - (Code GE2), versions, exercise 29.10.2003
You are now conversant with the function diagram of the Telligent automatic transmission II and will no doubt have found some familiar components. The
Telligent automatic transmission II builds on the Telligent gearshift system II.
Various components are dispensed with or added to depending on the vehicle version. These differences are dealt with in this chapter. The biggest differences
are found in the all-wheel drive vehicles.
Task m Complete the table adding the distinguishing features for the Telligent gearshift system II and for the
Telligent automatic transmission II versions in the different possible vehicle configurations.
Note: For further information consult WIS GF26.21-W-0001MP "Electronic Drive Control (EAS)
Function" and circuit diagram PE26.20-W-2001 "Gearshift System (GS)".
Components dispensed with or ... replaced by GS II or additional ... if already installed previously,
located differently on the when compared with GS II located differently in EAS II
transmission for GS II
ACTROS models 930-934 with GE2
Clutch booster - Clutch actuator ----
---- - Transmission output speed - Transmission output

sensor (B57)
ACTROS models 930-934 with GE2 and
Clutch booster - Clutch actuator
all-wheel drive ----

sensor (B57)

sensor (B99)
Speed sensor (B17) ---- - Transfer case output
TR EAS II - (Code GE2), versions, exercise 30
EAS II - (Code GE2), teach-in process; exercise 29.10.2003
Task m There are two different teach-in processes for vehicles with Telligentâ automatic transmission II
EAS II (Code GE2).
Find out which teach-in process should be performed for which operations.
Mark the respective teach-in process with a cross in the table!
Note: For further information see AR54.21-W-0009A and AR54.21-W-0007-01D/02D.
Circumstances Teach-in process

Major Minor
Transmission exchange identical X
Transmission exchange not identical (different type) X
Gear module, gate module or range module replaced X
Sensor, split or clutch replaced X
Clutch replaced X
Clutch actuator replaced X
GS control unit replaced X
Non-identical engine replacement (different type, changed engine output) X
Identical engine replacement X
Non-identical PLD control unit replacement X
TR EAS II - (Code GE2), teach-in process; exercise 31
EAS II - (Code GE2), teach-in process and teach-in faults; exercise 29.10.2003
During the "minor" and "major" teach-in process in the GS system various fault messages can be displayed by the GS control unit on the instrument display.
These fault messages on the display refer to teach-in and operating faults.
Task m In which current service documentation can you read up on the corresponding teach-in and operating
faults and then take appropriate remedial action?
Indicate the correct answer.
a Diagnosis manual
b Electrical wiring diagrams
c Workshop Information System (WIS)
d Vehicle operator’s manual
E e Diagnosis Assistance System (DAS)
Task m Which basic conditions have to be fulfilled so that the teach-in process can be performed properly?
A a Battery voltage > 24 V

B b Parking brake actuated
C c Reservoir pressure > 8.5 bar
d Engine at idle speed
TR EAS II - (Code GE2), teach-in process and teach-in faults; exercise 32
Task m While you are performing the "major" teach-in process, GS II 28 comes up on the display and the
teach-in process is cancelled.
What does this message mean and which sign did you fail to observe during the teach-in process?
- Teach-in fault, engine not started
- If the neutral display is flashing, then the engine must be started
- after no longer than 10 seconds if the major teach-in process is being carried out.
Task m While you are performing the "minor" teach-in process, GS II 09 comes up on the display and the
teach-in process is cancelled.
What does this message mean and which sign did you fail to observe during the teach-in process?
- Teach-in fault, neutral position
- The "Neutral position" adopted at the start has been
- abandoned without request at +/- 40 counts
Notes
GS teach-in faults/text messages are located in the DAS simulation
under the appropriate menu
TR EAS II - (Code GE2), teach-in process and teach-in faults; exercise 33
EAS II - (Code GE2), clutch characteristics 29.10.2003
Clutch characteristics
Based on the clutch characteristics, the FR control unit detects the start or end position of the clutch drag point. The drag point has a short range in automated
clutch operation.
The drag point of the clutch is defined as follows:

When "Close clutch" is selected transfer of the engine torque starts, and when "Open clutch" is selected, transfer of the engine torque ceases at this point. The
drag point is at approximately 30 -50 % of the clutch operation.
Automated clutch operation attempts rapid overcoming of the "free travel" to the drag point.
Comfortable start-off, disengaging and maneuvering response should be guaranteed despite the "rapid" clutch operation.
Clutch operation mechanical path
0% 100%
Clutch operation Clutch drag range Clutch operation
TR EAS II - (Code GE2), clutch characteristics 34
Teaching in clutch characteristics
The clutch characteristics are continually teaching themselves in automatically while traveling.
The "adjustment" of the clutch characteristics does, however, become more sluggish as the length of operating time increases.
The clutch characteristics therefore need to be reset after the following work has been carried out:
Þ FR control unit replaced

Þ Engine or transmission removed or replaced
Þ Work performed on clutch and clutch operation
Þ Clutch actuator replaced
Þ "Minor/major teach-in process" carried out in the GS
Resetting the clutch characteristics
The clutch characteristics are reset by means of DAS in the FR control unit. The resetting of the "clutch characteristics" is menu-assisted.
"Clutch characteristics" is one of the points listed in the "Actuations" menu. Confirm this menu option and follow the further instructions given by DAS.
The stored clutch characteristics are then deleted from the control unit. After some 6-7 shift operations the new clutch characteristics are identified in the FR
control unit and stored. These serve as the new basis for adjusting the clutch response. The start-off and clutch response may seem rather awkward during the
first 6-7 shift operations required for teaching in the new clutch characteristics.
TR EAS II - (Code GE2), clutch characteristics 35
EAS II - (Code GE2), backup mode special features 29.10.2003
GS backup mode in EAS II
The GS backup mode in the Telligent automatic transmission II is released, activated and operated in the same way as in the Telligent gearshift system II.
Special feature of GS backup mode in EAS II
The only difference in the backup mode relates to the sensor unit. In the Telligent automatic transmission II sensor unit, the selector switch is also integrated in
the sensor unit.
When backup mode is operated, this can be used to select between manual or automatic backup mode.
There is no detectable difference between the "Manual" and "Automatic" operating modes.
1 Operating modes – selector

M Manual operation
A Automatic operation
EAS II sensor unit with selector switch N26.60-2205-31
TR EAS II - (Code GE2), backup mode special features 36
EAS II - (Code GE2), drive control actual values and GS II, exercise 29.10.2003
Actual values are stored in the control unit for the drive control
and GS II for a wide range of vehicle functions.
Our focus in this case is on the actual values connected with

the Telligent automatic transmission II (EAS II).
In order to gain an initial overview, we will attempt to allocate

the actual values to potential problem cases.
A large amount of current information on gear control and

clutch operation can be read out from the "Drive control actual
values and GS II" menu.
Many of these actual values can be referred to when diagnosing

different customer complaints.
As you can see from the printouts you have been given showing
current actual values for drive control and GS II, there is a large
number of actual values.
N26.00-2023-09
Task m Indicate which actual value groups for drive control and GS II may be of further help to you in
diagnosing the reasons for the customer complaints on the following page.
Discuss possible solutions in groups.
TR EAS II - (Code GE2), drive control actual values and GS II, exercise 37
Customer complaint GS II actual value group Drive control actual value group
GS teach-in process incorrectly · Transmission / control unit version Note: Only the actual value group designations are
terminated · Current vehicle status stated as proposed solutions.
(GS text message displayed) · Current and taught-in displacement and learned values
· Number of shifting cancellations
Inoperability of, e.g., engine brake, · Other ACTUAL values 1 · Engine brake
permanent brake, cruise control, · Other ACTUAL values 2 · Clutch
Temposet · Retarder
· Cruise control
· Clutch control Part 1
Gear selection/preselection not · Transmission / control unit version · Integrated automatic gear determination
possible/ · Current vehicle status · GS sensor unit for gear control
Splitter gearshift system not available/ · Shifting times · Clutch control Part 1
Reverse shifting not possible · Current and taught-in displacement and learned values · Clutch control Part 2
Shift abort · Shifting times

· Current and taught-in displacement and learned values
· Number of shifting cancellations
· State of solenoid valves for shifting operations
Poor start-off and maneuvering · Current and taught-in displacement and learned values · Clutch
response · Clutch control Part 1
Implausible gear selection · Transmission / control unit version
· Current vehicle status
· Other ACTUAL values 1
· Other ACTUAL values 2
TR EAS II - (Code GE2), drive control actual values and GS II, exercise 38
Foot throttle actuator, standard quantity; exercise 18.03.03
Task
The illustration shows a useful pedal range by way

of an example.
Idle thr. adjustm't range Full load adjustm't range
In the field marked "Foot throttle actuator
standard quantity" indicate the range of the 0% 10% 30% 40% 90% 100%
minimum and maximum injection quantity which Duty cycle
the driver can determine by using the foot throttle
actuator.
Lower Upper
pedal stop pedal stop
Discuss in groups why the foot throttle actuator
has to be taught in. 0% Useful pedal range 100%
Pedal range
Idle thr. Kickdown position ON

position
Kickdown position OFF
Full-load position
Foot throttle actuator

standard quantity
TM FFG 1_D.ppt
TR Foot throttle actuator, standard quantity; exercise 39
Foot throttle actuator, onboard teach-in, ACTROS models 930 - 934 09.10.2002
Requirement:
Activate the "Diagnosis" menu in the "Settings" menu (see operator's manual).
Teaching-in the foot throttle actuator:

· Select the "Diagnosis" menu
· Select the "Service info" submenu
Display
FR LEARN
To start the teach-in process, select "Reset with reset button".
____
A___
+___
Hold the accelerator in full-load position
+__A
+__+
To conclude the teach-in process, select "Reset with reset button" again.
FR OK
TR Foot throttle actuator, onboard teach-in, ACTROS models 930 - 934 40
Troubleshooting chart for GS II and EAS II shifting systems and notes on how to use it correctly 29.10.2003
41
· After "Ignition On" wait for the sound speaker to extinguish (automatic system check).
If the ignition key is turned again straight away, a system check cannot be fully carried out. As a result a "CAN communication" fault code is set in the
systems.
· There must be a guaranteed voltage supply of 24 V and, when starting up in particular, the voltage level should not fall below 20 volts.
Otherwise undervoltage, CAN communication and implausible speed sensor fault codes are set in the systems.
· Compressed air supply (8 bar) is very important for problem-free shifting.

Especially when starting at temperatures below +5 °C, an adequate supply of compressed air is required to open the drive clutch.
· The foot throttle actuator setting should be checked in case of doubt and readjusted if necessary.
Shift speed and gear allocation can be insufficient if the settings are incorrect.
TR Troubleshooting chart for GS II and EAS II shifting systems and notes on how to use it correctly 41 / 41
Troubleshooting chart for GS II and EAS II, TIPS procedure and application 29.10.2003
In order to facilitate a standard procedure of detection and diagnosis with regard to current complaints, the Wörth plant customer service department has
developed a troubleshooting chart for the Telligent automatic transmission II – GS II (Code GS7) and Telligent automatic transmission II – EAS II (Code GE2).
An important feature of the troubleshooting chart is its integration of current complaints communicated through TIPS.
How can I contact TIPS?
Intranet address: http://tips-reader.daimlerchrysler.com
Your provisional user name: ____________________ (request from MPC, country-specific)
Your provisional password: ____________________
Now you can search for a "TIPS" yourself.
Symptom: Engine brake and cruise control not working
Model: ACTROS 930-934 with Telligent automatic transmission II - EASII (Code GE2)
Have fun searching!
TR Troubleshooting chart for GS II and EAS II, TIPS procedure and application 41
Shift system troubleshooting chart for the Telligent gearshift system II – GS II (Code GS7) and Telligent automatic transmission II –
EAS II (Code GE2)
· Observe instructions for use in the operator's manual.
· "Observe" tips for problem-free use!
· Targeted questions regarding complaints at the time of vehicle acceptance.
Complaint in accordance Complaint in accordance with Complaint in accordance
with symptoms current fault code displayed with symptoms
Remedy according to "TIPS" design Read out fault code in GS + FR Read out abnormal termination
group 26 control unit counter in GS control unit
Crunching occurs Determine GS + FR control unit Assessment of abnormal termination

th th
when shifting from 4 to 5 gear version counter
discontinue clutch operation

Read out parameterization in GS
Mainly abnormal clutch terminations Mainly abnormal transmission

Crunching occurs Remedy according to DAS/WIS terminations
th th
when shifting from 4 to 5 gear
· Hold down clutch pedal for longer when · Check cable set connection to
shifting gear sensor system / transmission
· Check compressed air line cross · Check cable set connection to
sections solenoid valves / transmission
for restrictions
· Check compressed air system for leaks · Check cable set connection to
engine cable set separation point
· Check mechanical function of clutch · Check ground points in
components transmission cable set
· Check cable set connection to GS
control unit
· Check connectors visually for leaks
TR Troubleshooting chart for GS II and EAS II, TIPS procedure and application 42
Carrying out diagnosis with the layer model 28.04.03
Procedure Sources of inf. Logging

The complaint or symptom is specified. Order, data card, List, table
FDOK
Driver, customer
Sub-areas are defined for the affected functions. Own know-how, List, table, matrix
Faults are allocated to the sub-areas. WIS (AF, AD and GF
documents)
Introductions to
service manual
A test strategy is developed. Own know-how, Table, matrix,
· Sub-areas prioritized WIS (test troubleshooting chart,
· Information required for the function or system defined documents), decision tree, test
· Tests for sub-areas defined DAS, sheets
· Priorities set according to economic viability and probability Introductions to
service manual
· Teach-in processes taken into account
A test strategy is implemented.
· Test equipment stipulated with test modes and measuring points
· Target results defined, actual results determined and compared with target
· Components, media and settings evaluated or eliminated by testing
Test results List, description
The causes are established.
WIS
Repair is carried out. (Repair documents)
Operational check is carried out.
TR Carrying out diagnosis with the layer model 43
Log sheet Complaint level
a mb
Repair order no.:
Vehicle
Ident. no.
Account no. Date: ___. ___. 00
Location Registration number Initial registration Vehicle model Engine no. Mileage
Location Brought in by Accepted by Time Antifreeze in coolant Non-binding time

°C changed to °C hours
Location Fam.: Main Emissions §57 B GW-V erf.: WD-GR.: Change of date
inspection inspection
Model code: Dat. I. WD:
Listed Item Rg. Operation no. WU Oper. Proc. Type of operation DM
code code code
Log sheet Complaint level
Any further information? Sources of information? Notes
Log sheet Sub-area and function level
Defined sub-areas Defined functions Prioritization Notes
Log sheet Test level
Function:
Basic conditions required / What test / test In the .... What is being TARGET value ACTUAL value Notes / reference
information required equipment is being system tested?
used?
Log sheet Test level
Which test? Which test What is being tested? Prior- TARGET result ACTUAL result Reference
equipment? itiza-
tion
Log sheet for metaplan board Test level
Which test? Which test What is being TARGET result ACTUAL result Reference
equipment? tested?
EAS II - (Code GE2), practical 1; exercise 29.10.2003
Customer complaint m The customer complains that the engine brake and cruise control are not working on an ACTROS
2544 model 930-934 with Telligent automatic transmission II. A few days previously the customer
replaced the clutch himself.
No event is being displayed in the instrument.
The Actros is fitted with the following major assemblies:
Chassis no. WDB 930 203 .......

Engine 501 922 .....
Transmission 715 531 .....
Task m The customer complaint is remedied following a teach-in process. You may now wonder what does a
teach-in process have to do with the functioning of the engine brake and cruise control?
Enter your initial suppositions

- The engine brake and cruise control functions have something to do with the clutch sensing.
here
- This is because both functions can only be active when the clutch is closed.
- This is because the old taught-in value and the current value no longer agree in the "counts grid".
- Neither function is active.
- The values are resynchronized/updated by means of a teach-in process.
Note In case you still cannot see the connection between the functions and the clutch sensing, we aim to
establish this connection in the following exercises.
TR EAS II - (Code GE2), practical 1; exercise 50
Task m In which operating conditions can the engine brake and cruise control be activated?
Discuss the demands made on the functions in groups and complete the table.
Function Condition, minimum requirement in terms of ...

Engine speed Speed Clutch
Engine brake at least 900 rpm ------- closed

Cruise control -------- at least 30 km/h closed
Task m Let us refer back to the above customer complaint.

Check the vehicle to see whether the clutch disengages fully. This can be done with the help of actual
values in the GS II system and with the engine running.
Note down the respective actual values and complete the required values.
GS actual Actual value statement Actual clutch value with at engine idle speed Notes
value
not activated activated
02 Countershaft speed 600 0
034 Clutch displacement value in percentage 0 100
039 Clutch displacement value 945 475
051 Learned value "Clutch open" 475 475
052 Learned value "Clutch closed" 945 945
220 Engine speed 600 600
223 Clutch status closed open
Task m You can control the clutch actuator via the submenu "Clutch operation control" in the "Actuations"
menu in the drive control system.
For which customer complaints is it advisable to use the "Clutch operation control" menu?
Discuss possible options for use in groups and note them down.
- Start-off and maneuvering response
- Clutch-related complaints
- Abnormal shift terminations on account of inadequate clutch operation
- Aaa
- Aaa
Task m Carry out the "Clutch operation solenoid valves" actuations menu taking into account the following
task.
What causes may exist if you detect deviations in the clutch operation control loop with the help of
the "Clutch operation solenoid valves" actuations menu?
Complete the table.
Clutch opening is delayed Clutch fails to reach max. value Clutch closing is delayed Clutch fails to return to starting
(as per standard) position
The release bearing on the drive X X X X

shaft is sluggish
Clutch operation components X X

are wearing
Mechanical operation of clutch X X X X

actuator sluggish/faulty
Pneumatic reservoir pressure X X

too low
Pneumatic lines X X
clogged/restricted
Ventilation bores clogged/dirty X X
Customer complaint m A customer complains that the driver's shift commands are occasionally not implemented in an
ACTROS 2544 model 930-934 with Telligent automatic transmission II.
Chassis no. WDB 930 203 1K .......

Engine 501 922 .....
Task m Which electronic system(s) is (are) relevant for the diagnosis?
- FR control unit
- Aaa
Task m In the event of which specific customer complaints is it advisable to check that the GS sensor unit is
working correctly?
List them below.
- Start-off and reverse gear cannot be engaged
- Neutral cannot be engaged
- Gears cannot be skipped
- Aaa
Task m Check the GS sensor unit on the vehicle with the help of STAR DIAGNOSIS.
Perform the relevant shift operations.
Note down the respective GS II actual values and complete the required values.
GS actual Actual value statement Sensor unit Notes

value
activated not activated
105 "Shift up" selected on main lever of sensor unit Yes No
106 "Shift down" selected on main lever of sensor unit Yes No
107 "Shift up" selected on half-gear rocker of sensor unit Yes No
108 "Shift down" selected on half-gear rocker of sensor unit Yes No
109 Position of automatic system switch on gear control GS sensor unit Manual Automatic
110 "Neutral" signal of gear control GS sensor unit Yes No
111 Acknowledgement signal of gear control GS sensor unit Yes No
112 Function button pressed on gear control GS sensor unit Yes No
Notes
Customer complaint m The customer complains of abnormal shift terminations on an ACTROS 2544 model 930-934 with
Telligent automatic transmission II.
No event is being displayed in the instrument.
Chassis no. WDB 930 203 .......

Engine 501 922 .....
Task m What circumstances might cause a shift abort in the GS II or EAS II system?
Note down your findings/the special features.
Enter your initial suppositions
- 1. Difference between gate displacement values and learned values,
here
- Gear, splitter, range and clutch too large
- 2. Shift times are exceeded
- 3. Air admission and vent lines are clogged up or restricted
- 4. Mechanical wear or sluggishness in transmission
Task m You have replaced the clutch actuator because your diagnosis revealed it to be the cause of the
customer complaint. What teach-in process(es) do you still have to carry out in the GS II system?
- Minor GS II teach-in process and reset clutch characteristics in the drive control
Task m Carry out a "minor teach-in process" in the GS II system.
- Aaa
- Aaa.
- Aaa.
Task m Reset the "clutch characteristics" in the drive control system.

- Aaa
- Aaa.
- Aaa.
Do not forget to delete all fault codes in the individual systems!
» ... Die Mitarbeiter werden zukünftig in die Rolle persönlicher Wissensmanager hineinwachsen
müssen, die aktiv die Verantwortung für ihre Qualifizierung übernehmen ... « Jürgen E. Schrempp
» ... Staff must in future assume the role of personal knowledge managers, who actively take
responsibility for their own qualification ... « Jürgen E. Schrempp
Global Training.
The finest automotive learning
DaimlerChrysler AG
Global Training
HPC T301
D-70546 Stuttgart
Intranet: http://intra-gt.daimlerchrysler.com
st
1511 5555 02 1 edition 10.03 124

Daimler Chrysler Transmission

Uploaded by

Copyright:

Available Formats

Daimler Chrysler Transmission

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daimler Chrysler Transmission

Uploaded by

Copyright:

Available Formats

Trucks • Transmission

Telligent automatic transmission

Trucks • Transmission <> Telligent

Printed in Germany Note:

Welcome to the NGAS training course. As the training course progresses, it

If you have some experience and understanding in the areas of mechanics,

Networking of the Telligent automatic transmission II

DAS actual values of the GS II system and drive

Target group Mechanics, electricians

Methodology 50% theory, 50% practical

Duration 2 days DCVD, 2-3 days Export

Objectives The participant can:

· perform testing, adjusting and repair work

· Drive control on pneumatic (EAS) and hydraulic (AGS) shifting systems

· Carrying out the necessary teach-in processes

ACTROS, AXOR, ATEGO Changes to ACTROS models 930 - 934

Mechanical shift Hydraulic shift Telligent Telligent

Task m Enter the CAN BUS designations.

CAN 3 Frame CAN BUS CAN 10 Tachograph CAN BUS

ACTROS, models 950 -954

ACTROS, models 930 - 934

ACTROS, models 930 - 934

Component Terminal Fuse Relay

5 Gear, gate, range and splitter sensors

4 Gear, gate, range and splitter solenoid valves

Component Designation Communication / Connection Designation Component

B10 B15 B16 B65 B111

B11 B12 B14 S10 S11 S166 Y6-13 M1

The following questions may help you to solve the problem.

Reduce engine torque FR MR CAN 4

Operation Transmitter Receiver Relevant information Reason

Operation Transmitter Actual values Transmission Receiver Actual values

Close clutch GS 287 --- Y39.1/Y39.2 ---

The control units are networked together by a

Y6-13 M1 B11 B12 B14 S10 S11 S166

Module IW Information Information IW Pin Com- Module

The following components are integrated in the clutch actuator:

· Solenoid valves: Clutch aeration 1, Clutch aeration 2,

Each of the clutch positions can be moved to and

This basic principle applies:

Cylinder extended ® Clutch open

The clutch travel sensor (B2) records the current

MKUB1 Solenoid valve, aerate clutch with throttle

The task of the transmission output speed sensor

· To record the transmission output rpm

The additional recording of the transmission

The transmission output speed sensor (B57) is

Vehicles with Telligent automatic transmission II

This is because the speed sensor (B17) has been

For this reason the transmission output speed

Task m When is it necessary to readjust the clutch actuator plunger?

Task m How is the clutch actuator plunger adjusted?

- By mounting a special tool on the transmission housing

- By adapting the length of the plunger in line with the gauge

Clutch actuator solenoid valves

MKUB1 Solenoid valve, aerate clutch with throttle

---- - Transmission output speed - Transmission output

---- - Transmission output speed - Transmission output

---- - Transmission output speed - Transmission output

Speed sensor (B17) ---- - Transfer case output