Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Shieldfloor E200 To Protocol 2

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 2

Shieldfloor

E200

Two Component, Solvent Free, High Build, Gloss Finish, Epoxy Floor Coating

Description Typical Properties

Shieldfloor E200 is a two component, solvent free, Mixed Density : ~ 1.55 g/ml
pigmented, epoxy-based coating, which provides a Solids Content : 100% by volume
seamless, smooth, durable floor, at an applied thickness of 100% by weight
between 0.2 - 0.4 mm. Pot Life : 25°C ~ 40 minutes
A slip resistant finish can be produced by the use of Wet Film Thickness (WFT) / : 200 µm
Shieldgrain AS granules. Coat
Total Dry Film Thickness : 400 µm (2 coats)
Shieldfloor E200 is available in a range of standard colors.
Time Between Coats
Uses
Minimum : 20°C 24 hours
 Roller coat for medium to heavy wear surfaces such as: 30°C 16 hours
Maximum : 20°C 48 hours
 Factories and production plants 30°C 24 hours
 Car parks and showrooms Initial Cure 25°C 18 - 24 hours
35°C 12 - 18 hours
 Garages, workshops, and maintenance hangers Full Cure 25°C 7 - 10 days
 Broadcast anti-slip system wet areas where a high degree 35°C 5 - 7 days
of resistance to chemicals, oils and grease is required Taber Abrasion Resistance : < 50 mg
such as: ASTM D4060 CS17 Wheel
(1000 g, 1000 cycles)
 Food and beverage plants Wear Resistance : ≤ 50 µm
 Pharmaceutical and other medical facilities. EN 13892-4 (BCA)
Bond Strength : ≥ 2.0 MPa
 Warehouses with high density traffic EN 13892-8

 Vehicle movement areas Surface Hardness : 100 MPa


EN 13892-6

Characteristics / Advantages Impact Resistance : ≥ 4 Nm


EN ISO 6272
 Excellent wear, chemical, mechanical and abrasion
resistance Application Instructions
 Gloss finish
1. Application Conditions
 Easy to apply by brush, roller, or squeegee
 Economical Substrate:

 Slip resistant finish can be produced Temperature : +10°C to +35°C


and ≥ 3°C above dew point
 Factory controlled pre-proportioned packs for ease of use
Moisture Content : ≤ 4%
Standards Compliance Compressive Strength : ≥ 25.0 MPa
Pull Off Strength : ≥ 1.5 MPa
 EN 13813: SR - ARO,5 - B2,0 - IR4
 BS 8204-6: Type 2, 3 Ambient Air:
 ASTM C722: Class SP, and BC- EP
Temperature : +10°C to +35°C
Relative Humidity : < 80%

Page 1 of 2 Ref. Number: Shieldfloor E200 Issue 1 August 2021


Shieldfloor
E200

2. Substrate Preparation 35-38 m2/ 15 liters kit/ 2 coats application

The substrate must be clean, dry and free of all Calculated theoretically, actual consumption will be
contaminants such as dirt, oil, grease, coatings and surface subjected to the site condition, it may vary due to site
treatments, etc. wastage, substrate porosity, and substrate profile.

Concrete substrates should be prepared mechanically using Packaging


abrasive blast cleaning or scarifying equipment to remove
cement laitance and achieve an open textured surface. Shieldfloor E200 is available in 15-liter packs.

Weak or damaged concrete must be removed and surface Shelf Life and Storage
defects such as blow holes and voids must be repaired using
appropriate products from the Rep, Repflow, Shieldgrout Shieldfloor E200 has a shelf life of 12 months when stored
and Shieldrep ranges. in its original unopened packing in cool and dry conditions,
protected from direct sunlight, heat and moisture.
All dust, loose and friable material must be completely
removed from all surfaces preferably by brush or vacuum. Shelf life may reduce if the recommended storage conditions
are not followed.
3. Priming
Safety Instructions
Shieldfloor E100 does not require the substrate surface to
be primed before its application. Shieldfloor E200 contains resins, hardeners and solvents
and may cause irritation to skin or eyes. Refer to the most
4. Mixing recent Material Safety Data Sheet for information and advice
on the safe handling, storage and disposal of the product.
The base (Part A) and hardener (Part B) components should
be thoroughly stirred before the two are mixed together. Limitations
Pour the entire contents of the hardener container into the  Do not apply onto surfaces known to or are likely to suffer
base container and these two materials are mixed thoroughly from rising damp.
for 2 - 3 minutes using a slow speed mixing drill fitted with a
mixing paddle until a uniformly colored, homogenous mix is  As with all epoxy materials some slight shade changes
may be experienced over the long term when placed in
achieved.
adverse exposure conditions. Any such change in shade is
Avoid over mixing and do not add any thinners or solvents. not regarded as being detrimental to performance.
 Do not install at temperatures below 5°C.
5. Application
 Hot weather practices should be adopted during
Apply the mixed material by brush or roller onto the prepared application and curing if the temperature is above 30°C.
substrate. Pre-condition the material for at least 24 hours in a cool,
air-conditioned environment to ~ +20°C prior to mixing.
Typically, 2 coats are applied, each at 200 µm WFT, the
second coat being applied, at 90° to the first coat, as soon as Disclaimer
the first coat has initially dried.
Manaseer Industrial Complex has the right to amend its
Should the overcoating time be exceeded the first coat must datasheets at any time. Please make sure to have the latest
be lightly abraded before overcoating. published datasheet version.

Note: When an anti-slip finish is required the Shieldgrain AS


granules are broadcast onto the wet first coat. Excess This Product Is Environmentally Friendly
granules are removed by brush or vacuum prior to the
application of the second coat. To ensure full coverage of the
granules a third coat may be required.
Manaseer Industrial Complex
6. Cleaning is a member of US Green Building

All mixing and application equipment should be cleaned


immediately after use with a suitable solvent. Hardened
material should be mechanically removed.

Consumption
5 m2/ liter/ coat (WFT) will produce:

Page 2 of 2 Ref. Number: Shieldfloor E200 Issue 1 August 2021

You might also like