Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 92 views

    Installation Instructions: Honda Dealer: Please Give A Copy of These Instructions To Your Customer. Installation

    Uploaded by

    R B

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Installation Instructions: Honda Dealer: Please Give A Copy of These Instructions To Your Customer. Installation

    Uploaded by

    R B
    92 views3 pages

    Original Title

    08M70-MKW-D00

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    92 views3 pages

    Installation Instructions: Honda Dealer: Please Give A Copy of These Instructions To Your Customer. Installation

    Uploaded by

    R B

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Accessory Application Publication No.

    MII 17714
    INSTALLATION CENTERSTAND
    NC750XA/XD Issue Date
    P/N 08M70-MKW-D00
    INSTRUCTIONS April 2021

    Honda Dealer: Please give a copy of these instructions to your customer.


    PARTS LIST INSTALLATION
    (2) CAUTION
    (6) (4)
    • To prevent burns, allow the engine, exhaust system,
    radiator, etc., to cool before installing the accessory.
    NOTE:
    (7) • Be extremely careful when installing the springs as
    (3) the combined tension of the springs is very strong.
    • Keep the motorcycle on its side stand when installing
    the center stand.
    • The spring installation should be performed by two
    people. While one person holds the motorcycle,
    another person installs the spring.

    1. Remove the parts as shown.


    <Right side>
    (1) WASHER
    (5)
    BOLT
    NUT
    (8)

    No. Description Qty

    (1) Center stand 1


    (2) Center stand shaft 1
    (3) Spring (wide) 1
    (4) Spring (narrow) 1
    (5) Spring hook 1
    (6) 6 mm socket bolt 1
    (7) Rubber 1
    (8) Installation instructions 1

    TOOLS AND SUPPLIES REQUIRED WASHER


    Open-end wrench (12 mm) BOLT

    Hex wrench (5 mm)


    Spring tool (KL-9-C141) 2. Install the spring hook as shown.
    Mild soap detergent solution
    (Water : Soap / 100 : 1)
    Grease
    Shop towel
    Torque wrench

    TORQUE CHART
    Tighten all screws, bolts, and nuts to their specified
    torque values. Refer to the Service Manual for the torque
    values of the removed parts.
    Item N·m kgf·m Ibf·ft

    6 mm socket bolt 12 1.2 9


    Spring hook 22 2.2 16
    SPRING HOOK
    © 2021 Honda Motor Co., Ltd. - All Rights Reserved. 1 of 3 72MKW030
    3. Install the removed parts in the reverse order of 7. Install the center stand as shown.
    removal. <Left side>
    4. Apply mild soap detergent solution to the rubber in
    the area shown.

    SYNTHETIC DETERGENT SOLUTION


    Apply.
    RUBBER
    6 mm
    SOCKET
    BOLT

    5. Install the rubber as shown.

    CENTER STAND SHAFT

    RUBBER

    CENTER STAND

    CENTER STAND 8. Slide the spring (narrow) into the spring (wide).

    SPRING
    (narrow)
    RUBBER

    CENTER STAND

    SPRING
    (wide)

    6. Apply grease to the position shown.

    GREASE
    Apply.

    CENTER STAND SHAFT

    2 of 3
    9. Install the spring assembly as shown. • If the spring assembly is too hard to install,
    • First install the spring assembly to the spring remove the main stand shaft. First hook the
    hook, then to the center stand. spring assembly, then install the center stand
    • The spring installation should be performed shaft.
    by two people. While one person holds the CENTER STAND SHAFT
    Insert while aligning the holes
    motorcycle, another person installs the of the frame and center stand.
    spring.
    • For ease installation, first hook the spring 6 mm SOCKET BOLT

    (narrow).

    SPRING HOOK
    SPRING
    ASSEMBLY

    CENTER STAND

    CENTER STAND
    SPRING ASSEMBLY

    <SPRING INSTALLATION DIRECTION>

    SPRING HOOK SIDE

    CENTER STAND SIDE

    3 of 3

    You might also like