ROTARY SWITCHES integral

Series 25

DESCRIPTION

Integral Series 25 Professional grade Rotary Switches are ideally

suited for use in Industrial and Laboratory equipments. Double wiping self
cleaning contacts and choice of excellent Dielectric materials and suitable
plating finishes result in long term reliability and consistent quality.
An almost infinite variety of switching configuration meet most of the design
requirements of the user. Assembly options are possible with the use of
spacers, shields etc. and permit custom built switches. ‘O’ ring sealing is
available for both spindle and panel mounting bush. The balanced
pressure indexing mechanism provided by 2 balls housed in a steel base
provides smooth positive action with consistent and repeatable torque.
Switches type equivalent to JSS 51207 available.

FEATURES
l Choice of 30O, 45O, 60O and 90O indexing angles.
l Make before Break, Break before Make or special rotor segments
l Insulated shafts for RF circuits
l Concentric shafts for operating a pot meter mounted
at the rear of the switch (on request)
l Rigid or Flexible Tag PCB terminals (for single wafer only)
l Shields between wafers as per customer requirements
l Gold plating on clips/rotors available
l Dust proof caps to protect contacts from dust available
l Type approved to JSS 51207 available (with coin silver clips
and panel and spindle seal)

DIMENSIONAL DETAILS

METAL BASE PLATE TYPE

PLASTIC HOUSING TYPE

All Dimensions in mm.

C3
 SPECIFICATIONS MATERIALS & FINISHES

CONTACT RATING CONTACT CLIPS : Spring hard brass heavily Silver

CURRENT CARRYING : 2 amps (non-switching) Plated / Gold plated / Silver alloy
CURRENT BREAKING : 0.5 amps @ 28 V DC
0.25 amps @ 110 V AC ROTOR BLADES : Brass heavily Silver plated /
(Resistive) Gold plated
WORKING VOLTAGE : 230 V AC (max) STATOR & ROTOR : Moulded glass fibre loaded
INSULATION RESISTANCE : >1000 Megohms (between any Diallyl Phthalate / Nylon / PC
two insulated parts)
BASE : Steel sheet Zn plated
VOLTAGE PROOF : min 750 V AC And passivated.
In some cases high temperature
CONTACT RESISTANCE : <15 milliohms (Initial - adjacent Engineering plastics are also
Contact) @ 2-4V DC used.

TEMPERATURE RANGE : -650C to 850C INDEX MECHANISM : Index springs stainless steel
& other parts zinc yellow plated
LIFE : 25,000 operations And passivated.

INDEX ANGLE : 300, 450, 600 & 900

SEALING : Panel & Shaft seal on request

(Standard on switches which
meet JSS51207)

CHECK LIST FOR ORDERING : Given below are the variations possible in the Switch. Please take care to see that all these
points are taken note of if you are ordering a custom-built special switch. For contact configuration, other than standard, use the
layout sheet available on request.
L/P - Specify maximum overall length, if important
A - Shaft length - 10 mm (dia 6.35 mm)
Q - Shaft extension at rear nominal 2.0mm to 6.0mm (to
B - Bushing thread length - 9.5 mm / Threads 3/8”x32 TPI suit standard shaft available)
(Length 6.35 mm available on request)
R - Index angle 30O, 45O, 60O & 90O
C - Flat length - Standard 6mm (in no case closer than
3 mm from end of bushing) Optional S - Stopper - Yes/No
D - Angle of flat - Multiples of 15O +3O (specify position of T - Locating Lug - Yes/No
flat with switch shaft in fully counter-clockwise position
when viewed from front or knob end) U - Hollow shaft
E - Flat Dimension - 5.5 + 0.1 mm V - No. of Poles/Ways
I - First spacer - 3.0 mm with standard clips (No spacer W - Contact Terminals - Solder type/PCB type
needed if no clip present)
J - Spacer - 5.0mm with standard clips facing each other X - Contact - Silver/Gold plating/Silver alloy
M - Standard 4.0mm min (Any length spacer may be Y - Shields (dimension/position)
inserted at this point)
Z - Rotor - Non shorting (Break before Make) - N
N - 1.5mm to 5.0mm to suit standard screw available Shorting ( Make before Break) - S

HOW TO ORDER
1. For standard switch by describing as given below.
2. For special assembly use layout or send drawings.

ORDERING
2 5
10/2011 ISSUE 03, DCR 1182

CODE

*
S- Sheet
metal
No. of Poles No. of Ways N-Non Shorting
(Positions) S-Shorting
Clips G-Gold Plated D - Dust P - PC pins
B-Brass Silver
Plated
Cover PL - PC lugs }
P- Plastic
C-Coin Silver

* Note:- PC Pins & PC Lugs can be Supplied only without Dust Cover.
INTEGRAL SYSTEMS AND COMPONENTS PRIVATE LIMITED
D-388/1, 1st Block, 1st Stage, Peenya Industrial Estate, Bangalore - 560 058, India
Telefax: (080) 2839 1707 / 2839 1708 / 2839 1709 / 2839 1710
An ISO 9001:2008 Company Website: www.integralsys.in E-mail: inty.systems@gmail.com / sales@integralsys.in

C4
 KNOB FOR ROTARY SWITCHES
Series 90

DESCRIPTION

Integral Collet Knobs can be used for all types of Rotary Switches.
They are sturdily built and are able to withstand repeated use.
They are designed to meet the requirement of different shaft Dia.

Operation of knob, it is effective to rotate the pointer to give an

indication of switch position.

KEY FEATURES OF KNOB :-

* Simple construction with reliable operation.

* Simplicity of use.
* Styling

Knob is designed to have easy fit of accessories giving more

versatility.

KNOB STYLE :- Standard

MATERIALS & FINISHES

MOULDINGS : Engineering Plastic (matt finish)

METAL : Brass, Nickel Plated.

DIMENSIONS OF KNOB

ORDERING CODE:- COLOUR COLLET DIA

0 - Light Grey 0 - 6.35 mm dia.
1 - Dark Grey 1 - 6.0 mm dia.
2 - Black
10/2011 ISSUE 03, DCR 1182

K 9 0
All Dimensions in mm.

INTEGRAL SYSTEMS AND COMPONENTS PRIVATE LIMITED

D-388/1, 1st Block, 1st Stage, Peenya Industrial Estate, Bangalore - 560 058, India
Telefax: (080) 2839 1707 / 2839 1708 / 2839 1709 / 2839 1710
An ISO 9001:2008 Company Website: www.integralsys.in E-mail: inty.systems@gmail.com / sales@integralsys.in

C18