Wiper & Washer: Section
Wiper & Washer: Section
SECTION
WIPER & WASHER
WW B
E
CONTENTS
BASIC INSPECTION .................................... 4 Diagnosis Procedure ...............................................25 F
DIAGNOSIS AND REPAIR WORKFLOW .......... 4 FRONT WIPER MOTOR LO CIRCUIT .............. 26
Work Flow ................................................................. 4 Component Function Check ....................................26
G
Diagnosis Procedure ...............................................26
FUNCTION DIAGNOSIS ............................... 6
FRONT WIPER MOTOR HI CIRCUIT ............... 28
FRONT WIPER AND WASHER SYSTEM .......... 6 Component Function Check ....................................28 H
System Diagram ........................................................ 6 Diagnosis Procedure ...............................................28
System Description ................................................... 6
Component Parts Location ........................................ 9 FRONT WIPER AUTO STOP SIGNAL CIR-
I
Component Description .......................................... 10 CUIT .................................................................. 30
Component Function Check ....................................30
REAR WIPER AND WASHER SYSTEM ...........11 Diagnosis Procedure ...............................................30
System Diagram ...................................................... 11 J
System Description ................................................. 11 FRONT WIPER MOTOR GROUND CIRCUIT ... 32
Component Parts Location ...................................... 13 Diagnosis Procedure ...............................................32
Component Description .......................................... 13 K
WASHER SWITCH ............................................ 33
HEADLAMP WASHER SYSTEM .......................14 Description ...............................................................33
System Diagram ...................................................... 14 Component Inspection .............................................33
System Description ................................................. 14 WW
Component Parts Location ...................................... 15
RAIN SENSOR .................................................. 34
Component Description .......................................... 16 Description ...............................................................34
Diagnosis Procedure ...............................................34
M
DIAGNOSIS SYSTEM (BCM) ............................17
REAR WIPER MOTOR CIRCUIT ...................... 35
COMMON ITEM ......................................................... 17 Component Function Check ....................................35
COMMON ITEM : CONSULT-III Function (BCM - Diagnosis Procedure ...............................................35 N
COMMON ITEM) ..................................................... 17
REAR WIPER AUTO STOP SIGNAL CIRCUIT
WIPER ....................................................................... 17 ... 37
WIPER : CONSULT-III Function (BCM - WIPER).... 17 O
Component Function Check ....................................37
Diagnosis Procedure ...............................................37
DIAGNOSIS SYSTEM (IPDM E/R) .....................20
Diagnosis Description ............................................. 20 HEADLAMP WASHER RELAY ........................ 39 P
CONSULT-III Function (IPDM E/R) ......................... 22 Component Inspection .............................................39
WW-1
HEADLAMP WASHER CIRCUIT ...................... 42 Removal and Installation ....................................... 102
Component Function Check ................................... 42 Inspection and Adjustment .................................... 103
Diagnosis Procedure .............................................. 42
WASHER TANK ............................................... 104
FRONT WIPER AND WASHER SYSTEM ......... 45 Exploded View ...................................................... 104
Wiring Diagram - FRONT WIPER AND WASHER Removal and Installation ....................................... 104
SYSTEM - ............................................................... 45
WASHER PUMP ............................................... 105
REAR WIPER AND WASHER SYSTEM ........... 50 Exploded View ...................................................... 105
Wiring Diagram - REAR WIPER AND WASHER Removal and Installation ....................................... 105
SYSTEM - ............................................................... 50
HEADLAMP WASHER PUMP ......................... 106
HEADLAMP WASHER SYSTEM ...................... 54 Exploded View ...................................................... 106
Wiring Diagram - HEADLAMP WASHER - ............. 54 Removal and Installation ....................................... 106
ECU DIAGNOSIS ........................................ 57 FRONT WASHER NOZZLE AND TUBE .......... 107
Exploded View ...................................................... 107
BCM (BODY CONTROL MODULE) .................. 57 Hydraulic Layout ................................................... 107
Reference Value ..................................................... 57 Removal and Installation ....................................... 107
Wiring Diagram - BCM - ......................................... 74 Inspection and Adjustment .................................... 108
Fail Safe ................................................................. 80
DTC Inspection Priority Chart .............................. 81 FRONT WIPER ARM ........................................ 110
DTC Index .............................................................. 82 Exploded View ...................................................... 110
Removal and Installation ....................................... 110
IPDM E/R (INTELLIGENT POWER DISTRI- Adjustment ............................................................ 110
BUTION MODULE ENGINE ROOM) ................. 83
Reference Value ..................................................... 83 FRONT WIPER DRIVE ASSEMBLY ................ 112
Wiring Diagram - IPDM E/R - .................................. 88
LHD MODELS ......................................................... 112
Fail Safe ................................................................. 91
LHD MODELS : Exploded View ............................ 112
DTC Index .............................................................. 93
LHD MODELS : Removal and Installation ............ 112
SYMPTOM DIAGNOSIS ............................. 94 LHD MODELS : Disassembly and Assembly ........ 113
WW-2
Removal and Installation ....................................... 123 Inspection and Adjustment .................................... 124
A
WW
WW-3
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001452152
OVERALL SEQUENCE
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
WW-4
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
>> GO TO 2.
2.SYMPTOM CHECK A
>> GO TO 4. D
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected? E
YES >> GO TO 5.
NO >> GO TO 6.
F
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
G
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK H
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7. I
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part. J
>> GO TO 9.
K
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
WW
>> GO TO 9.
9.MALFUNCTION PART REPAIR M
Repair or replace the malfunctioning part.
>> GO TO 10. N
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is O
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5. P
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
WW-5
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
FRONT WIPER AND WASHER SYSTEM
System Diagram INFOID:0000000001208925
JPLIA0151GB
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION (LINKED WITH VEHICLE SPEED)
WW-6
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM transmits the front wiper request signal (INT) to IPDM E/R with CAN communication according to the
front wiper INT operation condition and the intermittent operation delay interval judged value. A
Front wiper INT operating condition
- Ignition switch ON
- Front wiper switch INT B
WW
M
JPLIA0094GB
WW-7
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
JPLIA0410GB
NOTE:
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 3 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The washer pump is grounded through the combination switch with the front washer switch ON.
FRONT WIPER FAIL−SAFE OPERATION
• IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to
PCS-24, "Fail Safe".
• BCM performs fail-safe operation when light and rain sensor or light and rain sensor-related systems are
malfunctioning. Refer to BCS-63, "Fail Safe".
WW-8
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001208927
WW
JPLIA0401ZZ
M
WW-9
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Description INFOID:0000000001208928
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM.
IPDM E/R
• Performs the auto stop control of the front wiper.
Combination switch
Refer to BCS-11, "System Diagram".
(Wiper & washer switch)
Combination meter Transmits the vehicle speed signal to BCM with CAN communication.
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal
Light and rain sensor
to BCM through the light and rain sensor serial link.
WW-10
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
A
System Diagram INFOID:0000000001208929
JPLIA0334GB F
G
OUTLINE
The rear wiper is controlled by each function of BCM.
H
Control by BCM
• Combination switch reading function
• Rear wiper control function
I
REAR WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM controls the rear wiper to start or stop.
J
REAR WIPER ON OPERATION
• BCM supplies power to the rear wiper motor according to the rear wiper ON operating condition.
K
Rear wiper ON operating condition
- Ignition switch ON
- Rear wiper switch ON
WW
REAR WIPER INT OPERATION
• BCM supplies power to the rear wiper motor according to the INT operating condition.
Rear wiper INT operating condition M
- Ignition switch ON
- Rear wiper switch INT
• BCM controls the rear wiper to operate once.
• BCM detects the rear wiper motor stopping position. N
• BCM supplies power to the rear wiper motor after an intermittent from the stop of the rear wiper motor.
JPLIA0165GB
WW-11
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM reads an auto stop signal from the rear wiper motor to detect a rear wiper motor position.
• When the rear wiper motor is at other than the stopping position, BCM continues to supply power to the rear
wiper motor until it returns to the stopping position.
JPLIA0166GB
NOTE:
BCM stops supplying power to the rear wiper motor when the ignition switch is turned OFF.
REAR WIPER OPERATION LINKED WITH WASHER
• BCM supplies power to the rear wiper motor according to the washer linked operating condition of rear
wiper. When the rear washer switch is turned OFF, BCM controls rear wiper to operate approximately 3
times.
Washer linked operating condition of rear wiper
- Ignition switch ON
- Rear washer switch ON (0.4 second or more)
• The washer pump is grounded through the combination switch with the rear washer switch ON.
REAR WIPER FAIL−SAFE OPERATION
BCM performs the fail-safe function when the rear wiper auto stop circuit is malfunctioning. Refer to BCS-63,
"Fail Safe".
WW-12
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001208931
JPLIA0402ZZ
J
1. Combination switch 2. BCM 3. Washer pump
4. Rear wiper motor
A. Over the glove box B. Radiator core support (RH) C. Back door trim finisher lower inside
K
WW
Part Description
• Judges each switch status by the combination switch reading function. M
BCM • Supplies power to the rear wiper motor.
• Performs the auto stop control of the rear wiper.
Combination switch
Refer to BCS-11, "System Diagram". N
(Wiper & washer switch)
WW-13
HEADLAMP WASHER SYSTEM
< FUNCTION DIAGNOSIS >
HEADLAMP WASHER SYSTEM
System Diagram INFOID:0000000001208933
JPLIA0464GB
OUTLINE
• Headlamp washer system has following two operations.
- Normal operation by the headlamp washer switch
- Operation linked with front washer
• Headlamp washer is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Headlamp washer control function
Control by IPDM E/R
• Headlamp washer relay control function
HEADLAMP WASHER OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the headlamp washer request signal to IPDM E/R with CAN communication depending on
each operating condition of the headlamp washer.
Operation is headlamp washer switch
- Ignition switch ON
- Headlamps ON (PASS excluded)
- Headlamp washer switch ON
Operation is front washer switch (The first time)
- Ignition switch ON
- Headlamps ON (PASS excluded)
- Front washer switch ON at first time
Operation is front washer switch (From the second time)
- Ignition switch ON
- Headlamps ON (PASS excluded)
WW-14
HEADLAMP WASHER SYSTEM
< FUNCTION DIAGNOSIS >
- Front washer switch ON at fifteenth time after the first time
A
E
JPLIA0335GB
• IPDM E/R turns ON/OFF the headlamp washer relay by receiving the headlamp washer request signal, and
controls the headlamp washer. F
Component Parts Location INFOID:0000000001208935
WW
JPLIA0403ZZ
WW-15
HEADLAMP WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Component Description INFOID:0000000001208936
Part Description
• Judges each switch status by the combination switch reading function.
BCM
• Requests (with CAN communication) the headlamp washer relay ON to IPDM E/R.
Controls the integrated relay according to the request (with CAN communication) from
IPDM E/R
BCM.
Combination switch
Refer to BCS-11, "System Diagram".
(Wiper & washer switch)
Headlamp washer switch Headlamp washer switch inputs the signals to BCM when pressing the switch.
WW-16
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001452161
B
APPLICATION ITEM
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
C
Diagnosis mode Function description
ECU Identification BCM part number is displayed.
D
Self-Diagnostic Results Displays the diagnosis results judged by BCM. Refer to BCS-65, "DTC Index".
Data Monitor BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM. E
Work Support Changes the setting for each system function.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM. F
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
H
WORK SUPPORT
WW-17
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DATA MONITOR
Monitor Item
Description
[Unit]
VEHICLE SPEED
The value of the vehicle speed signal received from combination meter with CAN communication.
[km/h]
IGN ON SW Ignition switch ON status judged from ignition power supply.
IGN SW CAN Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[OFF/ON]
FR WIPER LOW
[OFF/ON]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER INT
[OFF/ON]
FR WASHER SW
[OFF/ON]
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 7]
FR WIPER STOP
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
[OFF/ON]
RR WIPER ON
[OFF/ON]
RR WIPER INT
Each switch status that BCM judges from the combination switch reading function.
[OFF/ON]
RR WASHER SW
[OFF/ON]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor.
[OFF/ON]
REVERSE SW CAN NOTE:
[OFF/ON] The item is indicated, but not monitored.
H/L WASH SW
Switch status input from headlamp washer switch.
[OFF/ON]
ACTIVE TEST
WW-18
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Test item Operation Description
A
ON Outputs the voltage to operate the rear wiper motor.
RR WIPER
OFF Stops the voltage to stop.
Transmits the headlamp washer request signal to IPDM E/R with CAN communication B
HEADLAMP WASHER ON
to operate the headlamp washer operation.
WW
WW-19
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description INFOID:0000000001452162
JPMIA0313ZZ
WW-20
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Operation A
Inspection location Operation
sequence
A Oil pressure warning lamp Blinks continuously during operation of auto active test.
1 Rear window defogger 10 seconds B
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps C
3 10 seconds
• Tail lamps
• Front fog lamps
4 Headlamps LO ⇔ HI 5 times D
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
E
Concept of auto active test
JPMIA0310GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto K
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode WW
WW-21
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Symptom Inspection contents Possible cause
• Communication signal between BCM
and auto amp.
• BCM
YES • CAN communication signal between
Perform auto active test. BCM and ECM
A/C compressor does not operate Does the magnet clutch oper- • CAN communication signal between
ate? ECM and IPDM E/R
• Magnet clutch
• Harness or connector between IPDM
NO
E/R and magnet clutch
• IPDM E/R
• Harness or connector between IPDM
E/R and oil pressure switch
YES
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal between
lamp blink? IPDM E/R and BCM
NO • CAN communication signal between
BCM and combination meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal between
ECM and IPDM E/R
• Cooling fan motor-2 power supply cir-
cuit
• Cooling fan motor-1 ground circuit
• Cooling fan relay-4 or cooling fan re-
lay-5 power supply circuit
• Cooling fan relay-5 ground circuit
Perform auto active test. • Harness or connector between IPDM
Cooling fan does not operate E/R and cooling fan motor
Does the cooling fan operate?
• Harness or connector between IPDM
NO
E/R, and cooling fan relay-4 or cooling
fan relay-5
• Harness or connector between cooling
fan motor-2, and cooling fan relay-4 or
cooling fan relay-5
• Cooling fan relay-4 or cooling fan re-
lay-5
• Cooling fan motor
• IPDM E/R
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC
Refer to PCS-26, "DTC Index".
DATA MONITOR
Monitor item
WW-22
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
ACTIVE TEST
Test item
WW-23
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
WW-24
WIPER AND WASHER FUSE, FUSIBLE LINK
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
WIPER AND WASHER FUSE, FUSIBLE LINK
Description INFOID:0000000001208941
B
E
1.CHECK FUSES AND FUSIBLE LINK
Check that the following fuses and fusible link are not fusing.
F
Unit Location No. Capacity
Front wiper motor IPDM E/R 48 30 A
Washer pump Fuse block 4 10 A G
Headlamp washer pump Fuse and fusible link block G 30 A
Is the fuse or fusible link fusing? H
YES >> Replace the fuse or fusible link with a new one after repairing the applicable circuit.
NO >> The fuse or fusible link is normal.
I
WW
WW-25
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR LO CIRCUIT
Component Function Check INFOID:0000000001208943
IPDM E/R
Continuity
Connector Terminal Ground
E14 43 Not existed
Does continuity exist?
YES >> Repair the harness or connector. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
3.CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item.
3. With operating the test item, check voltage between IPDM E/R harness connector and ground.
WW-26
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals A
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER B
Connector Terminal
Ground Battery
LO
E14 43 voltage
C
OFF 0V
Is the measurement value normal?
YES >> GO TO 4. D
NO >> Replace IPDM E/R.
4.CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
E
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
F
IPDM E/R Front wiper motor
Continuity
Connector Terminal Connector Terminal
G
E14 43 E20 3 Existed
Does continuity exist?
YES >> Replace front wiper motor. H
NO >> Repair the harness or connector.
WW
WW-27
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
Component Function Check INFOID:0000000001208945
IPDM E/R
Continuity
Connector Terminal Ground
E14 42 Not existed
Does continuity exist?
YES >> Repair the harness or connector. And then replace the fuse.
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
3.CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch ON.
2. Select "FRONT WIPER" of IPDM E/R active test item.
3. With operating the test item, check voltage between IPDM E/R harness connector and ground.
WW-28
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals A
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIPER B
Connector Terminal
Ground Battery
HI
E14 42 voltage
C
OFF 0V
Is the measurement value normal?
YES >> GO TO 4. D
NO >> Replace IPDM E/R.
4.CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
E
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
F
IPDM E/R Front wiper motor
Continuity
Connector Terminal Connector Terminal
G
E14 42 E20 5 Existed
Does continuity exist?
YES >> Replace front wiper motor. H
NO >> Repair the harness or connector.
WW
WW-29
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check INFOID:0000000001208947
Monitor
Monitor item Condition
status
Stop position STOP P
FR WIPER STOP Front wiper motor
Except stop position ACT P
Is the status of item normal?
YES >> Front wiper auto stop signal circuit is normal.
NO >> Refer to WW-30, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000001208948
Terminals
(+) (-) Voltage
IPDM E/R (Approx.)
IPDM E/R
Continuity
Connector Terminal Ground
E13 24 Not existed
Does continuity exist?
YES >> Repair the harness or connector.
NO >> Replace IPDM E/R.
3.CHECK FRONT WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
WW-30
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
WW
WW-31
FRONT WIPER MOTOR GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure INFOID:0000000001208949
WW-32
WASHER SWITCH
< COMPONENT DIAGNOSIS >
WASHER SWITCH
A
Description INFOID:0000000001208950
E
JPLIA0163GB
D : Terminal 11
J
JPLIA0164GB
K
Combination switch
Condition Continuity
Terminal
11 12 WW
Front washer switch ON
13 14
Existed
11 14
Rear washer switch ON M
12 13
Does continuity exist?
YES >> Wiper and washer switch is normal. N
NO >> Replace combination switch (Wiper and washer switch).
WW-33
RAIN SENSOR
< COMPONENT DIAGNOSIS >
RAIN SENSOR
Description INFOID:0000000001208952
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal to BCM
through the light and rain sensor serial link.
Diagnosis Procedure INFOID:0000000001208953
WW-34
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
A
Component Function Check INFOID:0000000001208954
F
1.CHECK REAR WIPER MOTOR OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn the ignition switch OFF. G
2. Disconnect rear wiper motor connector.
3. Turn the ignition switch ON.
4. Select "RR WIPER" of BCM active test item. H
5. With operating the test item, check voltage between BCM harness connector and ground.
Terminals
Test item I
(+) (−) Voltage
BCM (Approx.)
REAR WIPER
Connector Terminal J
Ground Battery
ON
M66 43 voltage
OFF 0V K
WW-35
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
WW-36
REAR WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
A
Component Function Check INFOID:0000000001208956
Monitor D
Monitor item Condition
status
Stop position ON
RR WIPER STOP Rear wiper motor
Except stop position OFF E
G
1.CHECK REAR WIPER MOTOR (AUTO STOP) OUTPUT VOLTAGE
1. Turn the ignition switch OFF.
2. Disconnect rear wiper motor connector. H
3. Turn the ignition switch ON.
4. Check voltage between BCM harness connector and ground.
I
Terminals
(+) (−) Voltage
BCM (Approx.) J
Connector Terminal Ground
M66 44 Battery voltage
K
Is the measurement value normal?
YES >> GO TO 3.
NO >> GO TO 2. WW
2.CHECK REAR WIPER MOTOR (AUTO STOP) SHORT CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM connector. M
3. Check continuity between BCM harness connector and ground.
BCM N
Continuity
Connector Terminal Ground
M66 44 Not existed
O
Does continuity exist?
YES >> Repair the harness or connector.
NO >> Replace BCM. P
3.CHECK REAR WIPER MOTOR (AUTO STOP) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear wiper motor harness connector.
WW-37
REAR WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
WW-38
HEADLAMP WASHER RELAY
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER RELAY
A
Component Inspection INFOID:0000000001208958
WW
WW-39
HEADLAMP WASHER SWITCH
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER SWITCH
Description INFOID:0000000001301413
Headlamp washer switch inputs the signals to BCM when pressing the switch.
Component Function Check INFOID:0000000001301414
Terminals
Condition
(+) (−)
Voltage (Approx.)
BCM Headlamp Washer
Connector Terminal switch
While pressing 0V
Ground
M65 35
While not pressing
JPMIA0154GB
WW-40
HEADLAMP WASHER SWITCH
< COMPONENT DIAGNOSIS >
YES >> GO TO 3.
NO >> Repair the harness or connector. A
3.CHECK HEADLAMP WASHER SWITCH SIGNAL SHORT CIRCUIT
Check continuity between the headlamp washer switch harness connector and the ground.
B
WW
WW-41
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER CIRCUIT
Component Function Check INFOID:0000000001208959
Terminals
(+) (−) Voltage
Headlamp washer relay (Approx.)
Connector Terminal
Ground
2
E32 Battery voltage
5
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair the harness or connector.
3.CHECK HEADLAMP WASHER RELAY
Check headlamp washer relay. Refer to WW-39, "Component Inspection".
Is the headlamp washer relay normal?
YES >> GO TO 4.
NO >> Replace the headlamp washer relay.
4.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OUTPUT
CONSULT-III ACTIVE TEST
1. Install headlamp washer relay.
2. Turn the ignition switch ON.
3. Select "HEADLAMP WASHER" of IPDM E/R active test item.
4. With operating the test item, check voltage between IPDM E/R harness connector and ground.
WW-42
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals A
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
HEADLAMP B
Connector Terminal WASHER
Ground ON 0V
E14 35 Battery C
OFF
voltage
Is the measurement value normal?
YES >> GO TO 7. D
Fixed at 0 V >> GO TO 5.
Fixed at Battery voltage >> Replace IPDM E/R.
5.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OPEN CIRCUIT E
IPDM E/R
Continuity
Connector Terminal Ground K
E14 35 Not existed
Does continuity exist?
YES >> Repair the harness or connector. WW
NO >> Replace IPDM E/R.
7.CHECK HEADLAMP WASHER PUMP OPEN CIRCUIT M
1. Turn the ignition switch OFF.
2. Disconnect headlamp washer pump connector.
3. Remove headlamp washer relay.
4. Check continuity between headlamp washer relay harness connector and headlamp washer pump har- N
ness connector.
WW-43
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
WW-44
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
A
Wiring Diagram - FRONT WIPER AND WASHER SYSTEM - INFOID:0000000001208961
WW
P
JCLWA0512GB
WW-45
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
JCLWA0513GB
WW-46
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
JCLWA0514GB
WW-47
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
JCLWA0515GB
WW-48
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
JCLWA0516GB
WW-49
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
Wiring Diagram - REAR WIPER AND WASHER SYSTEM - INFOID:0000000001208962
JCLWA0517GB
WW-50
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
JCLWA0518GB
WW-51
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
JCLWA0519GB
WW-52
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
JCLWA0520GB
WW-53
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER SYSTEM
Wiring Diagram - HEADLAMP WASHER - INFOID:0000000001208963
JCLWA0521GB
WW-54
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
WW
JCLWA0522GB
WW-55
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
JCLWA0523GB
WW-56
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001452168
B
WW-57
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
NOTE: On
UNLOCK WITH DR
The item is indicated, but not monitored Off
Vehicle speed sensing auto door lock function does not operate Off
LOCK WITH SPEED
Vehicle speed sensing auto door lock function is operating On
Ignition switch OFF Off
ACC ON SW
Ignition switch ACC or ON On
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
Lighting switch OFF Off
TAIL LAMP SW
Lighting switch 1ST On
Turn signal switch OFF Off
TURN SIGNAL R
Turn signal switch RH On
Turn signal switch OFF Off
TURN SIGNAL L
Turn signal switch LH On
Lighting switch OFF Off
HI BEAM SW
Lighting switch HI On
Lighting switch OFF Off
HEAD LAMP SW 1
Lighting switch 2ND On
Lighting switch OFF Off
HEAD LAMP SW 2
Lighting switch 2ND On
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Lighting switch OFF Off
AUTO LIGHT SW
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On
Engine stopped Off
ENGINE RUN
Engine running On
Light & rain sensor is in normal condition OK
LIT-SEN FAIL
Light & rain sensor is with error NOTOK
Outside of the room is dark On
AUT LIGHT SYS
Outside of the room is bright Off
Displays a setting time of the follow
HD LIGHT TIME — me home function set by the work
support
Ignition switch OFF or ACC Off
IGN SW CAN
Ignition switch ON On
Front wiper switch OFF Off
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off
FR WIPER INT
Front wiper switch INT On
WW-58
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7 B
Any position other than front wiper stop position Off
FR WIPER STOP
Front wiper stop position On
Rear wiper switch OFF Off C
RR WIPER ON
Rear wiper switch ON On
Rear wiper switch OFF Off
RR WIPER INT D
Rear wiper switch INT On
Rear wiper stop position Off
RR WIPER STOP
Other than rear wiper stop position On E
Rear washer switch OFF Off
RR WASHER SW
Rear washer switch ON On
F
NOTE: Off
REVERSE SW CAN
The item is indicated, but not monitored On
When headlamp washer switch is not pressed Off G
H/L WASH SW
When headlamp washer switch is pressed On
Blower fan motor switch OFF Off
FAN ON SIG H
Blower fan motor switch ON (other than OFF) On
Compressor ON is not requested from auto amp.
Off
(A/C indicator OFF, blower fan motor switch OFF or etc.)
AIR COND SW I
Compressor ON is requested from auto amp.
On
(A/C indicator ON and blower fan motor switch ON).
Hazard switch OFF Off
HAZARD SW J
Hazard switch ON On
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On K
When back door opener switch is not pressed Off
TRNK OPNR SW
When back door opener switch is pressed On
WW
Close the hood
NOTE: Off
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood On
M
WW-59
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
JSMIA0031GB
PHYSICAL VALUES
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT-III. Refer to
BCS-28, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-9, "System
Description".
WW-60
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
WW
WW-61
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V
Lighting switch HI
(Wiper intermittent dial 4)
JPMIA0166GB
1.3 V
JPMIA0167GB
1.3 V
JPMIA0169GB
1.3 V
1.3 V
WW-62
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
E
Lighting switch 1ST
(Wiper intermittent dial 4)
F
JPMIA0166GB
1.3 V
G
JPMIA0168GB
I
1.3 V
J
Any of the condition below
with all switch OFF
• Wiper intermittent dial 1 K
• Wiper intermittent dial 6
JPMIA0169GB
1.3 V WW
M
Rear wiper INT
(Wiper intermittent dial 4)
N
JPMIA0196GB
1.3 V
O
WW-63
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V
JPMIA0166GB
1.3 V
Combination
8 Combination switch switch
Ground Input Turn signal switch LH
(V) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0167GB
1.3 V
JPMIA0168GB
1.3 V
JPMIA0196GB
1.3 V
WW-64
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
F
JPMIA0166GB
1.3 V
G
9 Combination
Combination switch switch
H
(G)*3 Ground Input Lighting switch PASS
INPUT 2 (Wiper intermit-
(B)*4 tent dial 4)
JPMIA0167GB
I
1.3 V
JPMIA0168GB
1.3 V WW
N
JPMIA0196GB
1.3 V
O
WW-65
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.3 V
JPMIA0167GB
1.3 V
JPMIA0168GB
1.3 V
JPMIA0169GB
1.3 V
1.3 V
11 Input/
Ground Audio link — — —
(B) Output
WW-66
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
OFF
(When rear door RH C
12 Rear door closed)
Ground Rear door switch RH Input
(LG) switch RH
PKID0924E
11.2 V D
ON
(When rear door RH 0V
opened) E
F
OFF
13 Back door (When back door closed)
Ground Back door switch Input
(V) switch G
PKID0924E
11.2 V
ON H
0V
(When back door opened)
OFF
(When passenger door
14 J
Passenger door Passenger door closed)
(P)*3 Ground Input
switch switch
(BR)*4 PKID0924E
11.2 V K
ON
(When passenger door 0V
opened)
WW
M
OFF
15 (When driver door closed)
Driver door
(BR)*3 Ground Driver door switch Input
*4
switch N
(P) PKID0924E
11.2 V
ON
O
(When driver door 0V
opened)
WW-67
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
OFF
(When rear door LH
16 Rear door closed)
Ground Rear door switch LH Input
(GR) switch LH
PKID0924E
11.2 V
ON
(When rear door LH 0V
opened)
JPMIA0154GB
1.1 V
While pressing 0V
21 Input/
— CAN-L — —
(P) Output
22 Input/
— CAN-H — —
(L) Output
ON 0V
23 Security indica-
Ground Security indicator Output Blinking
(V) tor
JPMIA0014GB
10.3 V
OFF 12 V
Ignition switch OFF or ACC 12 V
JPMIA0156GB
8.7 V
25
Ground Alarm link Output — —
(G)
WW-68
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
26
Blower fan motor Blower fan mo- OFF C
(GR)*5 Ground Input
switch tor switch
(LG)*6
PKID0924E
11.2 V D
ON (other than OFF) 0V
E
Compressor ON is not re-
quested from auto amp.
(A/C indicator OFF, blow- F
er fan motor switch OFF
27
Ignition switch or etc.)
(P)*5 Ground A/C switch Input
*6
ON PKID0924E
(Y) 11.2 V G
Compressor ON is re-
quested from auto amp.
(A/C indicator ON and 0V H
blower fan motor switch
ON).
Ignition switch OFF or ACC 0V I
28 J
(LG)*7 Ground Shock detect sensor Input
Ignition switch ON
(R)*8
K
JPMIA0155GB
6.0 V
WW
29
Not pressed
M
Back door opener Back door
(LG)*3 Ground Input
switch opener switch
(O)*4
JPMIA0154GB N
1.2 V
Pressed 0V
O
P
32 Door lock/unlock Door lock/un- Not pressed
Ground
(BR) switch (Unlock) Input lock switch
JPMIA0154GB
1.2 V
Pressed to the unlock side 0V
WW-69
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
33
OFF
(W)*9 Ground Hazard switch Input Hazard switch
(Y)*10
JPMIA0154GB
1.3 V
ON 0V
34
Door lock/unlock Door lock/un- Not pressed
(SB)*3 Ground
switch (Lock) Input lock switch
(P)*4
JPMIA0154GB
1.2 V
Pressed to the lock side 0V
JPMIA0154GB
1.2 V
Pressed to the lock side 0V
All switch OFF 0V
Turn signal switch RH
Lighting switch 2ND
Combination
36 Combination switch switch Lighting switch HI
Ground Output
(G) OUTPUT 5 (Wiper intermit-
tent dial 4)
Lighting switch 1ST
JPMIA0164GB
9.1 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4)
Rear washer switch ON
(Wiper intermittent dial 4)
37 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Any of the condition below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 5
• Wiper intermittent dial 6 JPMIA0161GB
9.1 V
Rear wiper switch ON
(Wiper intermittent dial 4)
WW-70
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF 0V
B
Front wiper switch LO
Front wiper switch MIST
Combination
38 Combination switch switch Front wiper switch INT C
Ground Output
(W) OUTPUT 3 (Wiper intermit- Lighting switch AUTO
tent dial 4)
9.3 V
All switch OFF 0V
E
Turn signal switch LH
Lighting switch PASS
Combination
39 Combination switch switch Lighting switch 2ND F
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Front fog lamp switch ON G
JPMIA0163GB
9.3 V
All switch OFF
0V H
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
I
Any of the condition below
40 Combination switch Combination with all switch OFF
Ground Output • Wiper intermittent dial 1
(P) OUTPUT 1 switch
• Wiper intermittent dial 2 J
• Wiper intermittent dial 3
• Wiper intermittent dial 6
• Wiper intermittent dial 7 JPMIA0160GB
9.1 V
K
Rear wiper switch INT
(Wiper intermittent dial 4)
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage WW
(LG) ply
O
Rear wiper stop position
44 Ignition switch
Ground Rear wiper auto stop Input
(B) ON
JPMIA0197GB P
WW-71
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
SKIA9232E
Not pressed 0V
Turn signal switch OFF 0V
47 Ignition switch
Ground Turn signal LH Output
(BR) ON Turn signal switch LH
PKID0926E
6.5 V
Turn signal switch OFF 0V
48 Ignition switch
Ground Turn signal RH Output
(GR) ON Turn signal switch RH
PKID0926E
6.5 V
49 OFF 0V
Ground Rear fog lamp Output Rear fog lamp
(Y) ON 12 V
50 Unlock 5V
Ground Unlock sensor Input Driver's door
(G) lock 0V
SKIA9232E
Not pressed 0V
55
Ground Ground — Ignition switch ON 0V
(B)
WW-72
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Not pressed 0V
B
D
SKIA9232E
H
60 Driver's door unlock Door lock/un- Pressed to the unlock side
Ground Output
(G) and fuel lid unlock lock switch
I
SKIA9232E
Not pressed 0V
*1: With Intelligent Key J
*2: Without Intelligent Key
*3: RHD models
*4: LHD models K
*5: With gasoline engine
*6: With diesel engine
*7: RHD models with side air bag WW
*8: LHD models with side air bag
*9: With xenon headlamp and daytime light system
*10: Except with xenon headlamp and daytime light system M
WW-73
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - BCM - INFOID:0000000001452169
JCMWA0500GB
WW-74
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
WW
JCMWA0501GB
WW-75
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
JCMWA0502GB
WW-76
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
WW
JCMWA0503GB
WW-77
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
JCMWA0504GB
WW-78
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
WW
JCMWA0505GB
WW-79
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
JCMWA0506GB
WW-80
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Priority DTC O
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
P
• B2191: DIFFERNCE OF KEY
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
• B2196: DONGLE NG
WW-81
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DTC Index INFOID:0000000001452172
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
WW-82
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
Reference Value INFOID:0000000001452173
B
VALUES ON THE DIAGNOSIS TOOL
ST RLY REQ When Intelligent Key is outside the vehicle, and the push switch
Off N
NOTE: is pushed
Vehicle without Intelligent Key system indi- When Intelligent Key is inside the vehicle, and the push switch is
cates only “ON”, and it does not change. On
pushed
Ignition switch OFF or ACC Off O
IGN RLY
Ignition switch ON On
Rear window defogger switch OFF Off
P
RR DEF REQ Ignition switch ON Rear window defogger switch ON
(Rear window defogger is operat- On
ing)
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close
WW-83
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
NOTE:
REV SW Off
This item is indicated, but not monitored.
Daytime running light system is not operated with lighting switch
DTRL REQ Off
OFF.
NOTE:
This item is monitored only on the vehicle Any of the condition below
with the daytime running light system. • Daytime running light system is operated. On
• Lighting switch 1ST, 2ND or AUTO (Light is illuminated)
HOOD SW Close the hood Off
NOTE:
This item is monitored only on the vehicle Open the hood On
with the vehicle security system.
THFT HRN REQ Not operation Off
NOTE:
This item is monitored only on the vehicle Horn is activated with vehicle security system. On
with the vehicle security system.
NOTE:
HORN CHIRP Off
This item is indicated, but not monitored.
TERMINAL LAYOUT
JPMIA0311ZZ
PHYSICAL VALUES
WW-84
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
7 Cooling fan motor-2 (HI) Cooling fan opera- OFF Battery voltage
Ground —
(P) ground tion HI 0V G
8 Cooling fan relay-2 power Cooling fan opera- OFF 0V
Ground Output
(G) supply tion HI Battery voltage
11
H
Ground Ground — Ignition switch ON 0V
(B)
Rear window defogger
12 0V
Rear window defogger re- switch OFF I
3
(O)* Ground Output Ignition switch ON
lay power supply Rear window defogger
(G)*4 Battery voltage
switch ON
• Parking lamp Turn off Battery voltage J
15*5 Ground
Daytime running light relay
Output
• License plate
(SB) control lamp Turn on 0V
• Tail lamp
K
16*6 Front fog lamp switch OFF 0V
Ground Front fog lamp (LH) Output Lighting switch 1ST
(Y) Front fog lamp switch ON Battery voltage
Front fog lamp switch OFF 0V WW
17*6 Ground Front fog lamp (RH) Output Lighting switch 1ST
(W) Front fog lamp switch ON Battery voltage
23 Engine stopped 0V
Ground Oil pressure switch Input Ignition switch ON
(W) Engine running Battery voltage
WW-85
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Front wiper stop position 0V
24
Ground Front wiper auto stop Input Ignition switch ON Any position other than
(Y) Battery voltage
front wiper stop position
25
Ground Ground — Ignition switch ON 0V
(B)
26 Input/
— CAN-L — —
(P) Output
27 Input/
— CAN-H — —
(L) Output
WW-86
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
• Ignition switch OFF or ACC
• After passing approximately 1 second or more 0V B
46*1 Fuel pump relay power after turning the ignition switch ON
Ground Output
(W) supply • For approximately 1 second after turning the
ignition switch ON Battery voltage C
• Engine running
After passing approximately 20 seconds or more
0V
47 after turning the ignition switch from ON to OFF D
(BR)*1 Ground ECM relay power supply Output • Ignition switch ON
(G)*2 • For approximately 20 seconds after turning ig- Battery voltage
nition switch from ON to OFF
E
After passing approximately 20 seconds or more
0V
48 after turning the ignition switch from ON to OFF
1
(R)* Ground ECM relay power supply Output • Ignition switch ON
(V)*2 • For approximately 20 seconds after turning ig- Battery voltage
F
nition switch from ON to OFF
WW-87
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
*5: With daytime running light system
*6: With front fog lamp system
*7: Halogen type headlamp
*8: With vehicle security system
*9: With headlamp washer system
*10: Without daytime running light system
JCMWA0420GB
WW-88
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
WW
JCMWA0421GB
WW-89
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
JCMWA0422GB
WW-90
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
WW
JCMWA0423GB
WW-91
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
• Parking lamps • The tail lamp relay and the daytime running light relay*1 turn ON when the ignition
• License plate lamps switch is turned ON
• Tail lamps • The tail lamp relay and the daytime running light relay*1 turn OFF when the ignition
• Illuminations switch is turned OFF
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The front wiper is operated at LO speed until the ignition switch is turned OFF if the
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF
Starter motor Starter relay OFF
Rear window defogger Rear window defogger relay OFF
2 Headlamp washer relay OFF
Headlamp washer*
WW-92
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Ignition switch Front wiper switch Front wiper auto stop signal A
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not B
ON
change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item C
“WIP PROT” while the wiper is stopped.
DTC Index INFOID:0000000001452176
D
WW
WW-93
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table INFOID:0000000001208973
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected.
WW-94
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
A
Combination switch
• Combination switch
Refer to BCS-67, "Symptom
• BCM
Table".
HI only Front wiper request signal B
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
IPDM E/R — C
Combination switch
• Combination switch
Refer to BCS-67, "Symptom
• BCM
Front wiper does not Table". D
stop. LO only Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
E
IPDM E/R —
Combination switch
• Combination switch
Refer to BCS-67, "Symptom
• BCM
Table".
F
INT only
Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ" G
• IPDM E/R
• Combination switch Combination switch
Intermittent adjustment • Harness between combination switch and BCM Refer to BCS-67, "Symptom
cannot be performed. • BCM Table". H
BCM —
Intermittent control
linked with vehicle Check the vehicle speed detection wiper setting. I
speed cannot be per- Refer to WW-17, "WIPER : CONSULT-III Function (BCM - WIPER)".
formed.
WW-95
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
Rear wiper motor circuit
• Combination switch
ON only Refer to WW-35, "Compo-
• BCM
Rear wiper does not nent Function Check".
stop. Combination switch
• Combination switch
INT only Refer to BCS-67, "Symptom
• BCM
Table".
• Combination switch Combination switch
Wiper is not linked to • Harness between rear wiper motor and BCM Refer to BCS-67, "Symptom
the washer operation. • BCM Table".
BCM —
Rear wiper does not
Rear wiper does not return to the stop posi-
operate normally. tion (Stops after a five- Rear wiper auto stop signal
second operation). • BCM
circuit
• Harness between rear wiper motor and BCM
Rear wiper stops after Refer to WW-37, "Compo-
• Rear wiper motor
operating for five sec- nent Function Check".
onds when ignition
switch is turned ON.
SYMPTOM DIAGNOSIS
Headlamp washer does not operate. “HEADLAMP WASHER DOES NOT OPERATE”
Refer to WW-98, "Diagnosis Procedure".
Wiper is not linked to
the front washer oper-
• Combination switch Combination switch
ation.
• Harness between combination switch and BCM Refer to BCS-67, "Symptom
(Operates normally
• BCM Table".
with headlamp washer
Headlamp washer switch)
does not operate nor-
mally. Does not operate with
headlamp washer • Headlamp washer switch
Headlamp washer switch
switch. • Harness between headlamp washer switch and
Refer to WW-42, "Compo-
(Operates normally BCM
nent Function Check".
with linked to front • BCM
washer)
• Headlamp washer relay
Headlamp washer circuit
• Harness between headlamp washer relay and
Headlamp washer does not stop. Refer to WW-42, "Compo-
IPDM E/R
nent Function Check".
• IPDM E/R
WW-96
NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
A
Description INFOID:0000000001208974
WW
WW-97
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
Description INFOID:0000000001208975
The front wiper does not operate under any operation conditions.
Diagnosis Procedure INFOID:0000000001208976
WW-98
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
Terminals A
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
FRONT WIPER B
Connector Terminal
Battery
LO
43 Ground voltage
C
OFF 0V
E14
Battery
HI
42 voltage D
OFF 0V
Is the measurement value normal?
YES >> Replace front wiper motor. E
NO >> Replace IPDM E/R.
5.CHECK FRONT WIPER REQUEST SIGNAL INPUT F
CONSULT-III DATA MONITOR
1. Select "FR WIP REQ" of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO.
G
3. With operating the front wiper switch, check the status of "FR WIP REQ".
WW-99
HEADLAMP WASHER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
HEADLAMP WASHER DOES NOT OPERATE
Description INFOID:0000000001301446
Headlamp washer does not operate with headlamp washer switch nor is linked to front washer operation.
Diagnosis Procedure INFOID:0000000001301447
Monitor
Monitor item Condition
status
WW-100
PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000001308746
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
Precaution for Procedure without Cowl Top Cover INFOID:0000000001308747
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc. H
PIIB3706J
K
WW
WW-101
HEADLAMP WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
HEADLAMP WASHER NOZZLE AND TUBE
Exploded View INFOID:0000000001208981
JPLIA0396ZZ
JPLIA0395ZZ
REMOVAL
1. Remove the front bumper fascia. Refer to EXT-12, "Exploded View".
2. Remove headlamp washer nozzle clip.
3. Remove headlamp washer tube from headlamp washer nozzle.
4. Remove headlamp washer nozzle from the front bumper fascia.
INSTALLATION
WW-102
HEADLAMP WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
Install in the reverse order of removal.
A
Inspection and Adjustment INFOID:0000000001306473
INSPECTION
B
Check Valve Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking. C
JPLIA0397ZZ
ADJUSTMENT F
JPLIA0466GB
J
WW
WW-103
WASHER TANK
< ON-VEHICLE REPAIR >
WASHER TANK
Exploded View INFOID:0000000001208985
JPLIA0372ZZ
REMOVAL
1. Remove the clip (A).
: Vehicle front
2. Pull out the washer tank inlet (1) from the washer tank.
3. Remove the fender protector RH (front). Refer to EXT-21,
"Exploded View".
4. Disconnect washer pump connector.
5. Disconnect headlamp washer pump connector.
6. Remove all washer tubes. JPLIA0373ZZ
7. Remove washer tank mounting nuts and bolt.
8. Remove the washer tank from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Add water up to the top of the washer tank inlet after installing. Check that there is no leakage.
WW-104
WASHER PUMP
< ON-VEHICLE REPAIR >
WASHER PUMP
A
Exploded View INFOID:0000000001208987
JPLIA0374ZZ
REMOVAL I
1. Remove the fender protector RH (front). Refer to EXT-21, "Exploded View".
2. Disconnect washer pump connector.
J
3. Remove front washer tube and rear washer tube.
4. Remove washer pump from the washer tank.
5. Remove the packing from the washer tank. K
INSTALLATION
Install in the reverse order of removal.
CAUTION: WW
Never twist the packing when installing the washer pump.
WW-105
HEADLAMP WASHER PUMP
< ON-VEHICLE REPAIR >
HEADLAMP WASHER PUMP
Exploded View INFOID:0000000001208989
JPLIA0394ZZ
REMOVAL
1. Remove the fender protector RH (front). Refer to EXT-21, "Exploded View".
2. Disconnect the headlamp washer pump connector.
3. Remove headlamp washer tube.
4. Remove headlamp washer pump from the washer tank.
5. Remove the packing from the washer tank.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never twist the packing when installing the washer pump.
WW-106
FRONT WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
A
Exploded View INFOID:0000000001306481
G
JPLIA0375ZZ
WW
N
JPLIA0376ZZ
P
REMOVAL
1. Remove cowl top cover. Refer to EXT-19, "Exploded View".
2. Disconnect front washer tube from front washer nozzle.
WW-107
FRONT WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
3. While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.
JPLIA0377ZZ
INSTALLATION
Install in the reverse order of removal.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment INFOID:0000000001208993
INSPECTION
Washer Nozzle Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
SKIB7926J
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
JPLIA0378ZZ
• LHD models
Unit: mm (in)
• RHD models
WW-108
FRONT WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
Unit: mm (in)
Insert a needle or similar object (B) into the spray opening (A) and
move up/down and left/right to adjust the spray position. D
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
E
SKIB7924J
WW
WW-109
FRONT WIPER ARM
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
Exploded View INFOID:0000000001208994
JPLIA0379GB
1. Front wiper blade (RH) 2. Front wiper arm (RH) 3. Front wiper arm cap
4. Front wiper blade (LH) 5. Front wiper arm (LH)
Refer to GI-4, "Components" for symbols in the figure.
REMOVAL
1. Operate the front wiper to move it to the auto stop position.
2. Open the hood.
3. Remove front wiper arm caps.
4. Remove the front wiper arm mounting nuts.
5. Raise front wiper arm, and remove front wiper arm from the vehicle.
INSTALLATION
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Operate the front wiper motor to move the front wiper to the auto
stop position.
3. Adjust the front wiper blade position. Refer to WW-110, "Adjust-
ment".
4. Install the front wiper arms by tightening the mounting nuts.
5. Inject the washer fluid.
6. Operate the front wiper to move it to the auto stop position.
7. Check that the front wiper blades stop at the specified position. ELH0717D
WW-110
FRONT WIPER ARM
< ON-VEHICLE REPAIR >
Standard clearance
R : 34.1 ± 7.5 mm (1.343 ± 0.295 in) A
L : 39.7 ± 7.5 mm (1.563 ± 0.295 in)
JPLIA0082ZZ
WW
WW-111
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
LHD MODELS
LHD MODELS : Exploded View INFOID:0000000001208997
REMOVAL VIEW
JPLIA0380ZZ
DISASSEMBLY VIEW
JPLIA0381ZZ
REMOVAL
1. Remove front wiper arm. Refer to WW-110, "Exploded View".
2. Remove cowl top cover. Refer to EXT-19, "Exploded View".
WW-112
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
3. Remove bolts from the front wiper drive assembly.
4. Disconnect the front wiper motor connector. A
5. Remove front wiper drive assembly from the vehicle.
INSTALLATION B
1. Install the front wiper drive assembly to the vehicle.
2. Connect the front wiper motor connector.
3. Operate the front wiper to move it to the auto stop position. C
4. Install the cowl top cover. Refer to EXT-19, "Exploded View".
5. Install front wiper arms. Refer to WW-110, "Exploded View".
D
LHD MODELS : Disassembly and Assembly INFOID:0000000001208999
DISASSEMBLY E
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the front wiper
F
linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
G
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position. H
3. Disconnect the front wiper motor connector.
4. Install front wiper motor to front wiper frame.
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame. I
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Do not drop front wiper motor or cause it to come into contact with other parts. J
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply multi−purpose grease or an equivalent if necessary.
RHD MODELS K
WW
REMOVAL VIEW
JPLIA0405ZZ
WW-113
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
DISASSEMBLY VIEW
JPLIA0406ZZ
REMOVAL
1. Remove front wiper arm. Refer to WW-110, "Exploded View".
2. Remove cowl top cover. Refer to EXT-19, "Exploded View".
3. Remove bolts from the front wiper drive assembly.
4. Disconnect the front wiper motor connector.
5. Remove front wiper drive assembly from the vehicle.
INSTALLATION
1. Install the front wiper drive assembly to the vehicle.
2. Connect the front wiper motor connector.
3. Operate the front wiper to move it to the auto stop position.
4. Install the cowl top cover. Refer to EXT-19, "Exploded View".
5. Install front wiper arms. Refer to WW-110, "Exploded View".
RHD MODELS : Disassembly and Assembly INFOID:0000000001209002
DISASSEMBLY
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position.
WW-114
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
3. Disconnect the front wiper motor connector.
4. Install front wiper motor to front wiper frame. A
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION: B
• Do not drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the wiper motor and wiper linkage joint (retainer). Apply
multi−purpose grease or an equivalent if necessary. C
WW
WW-115
RAIN SENSOR
< ON-VEHICLE REPAIR >
RAIN SENSOR
Exploded View INFOID:0000000001209003
WW-116
WIPER AND WASHER SWITCH
< ON-VEHICLE REPAIR >
WIPER AND WASHER SWITCH
A
Exploded View INFOID:0000000001209005
JPLIA0384ZZ
REMOVAL
1. Remove steering column cover. Refer to IP-11, "Exploded View". I
2. While pressing pawls, pull the wiper & washer switch. And disconnect it from the switch base.
INSTALLATION J
Install in the reverse order of removal.
WW
WW-117
HEADLAMP WASHER SWITCH
< ON-VEHICLE REPAIR >
HEADLAMP WASHER SWITCH
Exploded View INFOID:0000000001301411
JPLIA0400ZZ
REMOVAL
1. Remove instrument driver lower panel. Refer to IP-11, "Exploded View".
2. Widen the pawl. And remove headlamp washer switch.
INSTALLATION
Install in the reverse order of removal.
WW-118
REAR WIPER ARM
< ON-VEHICLE REPAIR >
REAR WIPER ARM
A
Exploded View INFOID:0000000001312089
G
JPLIA0409GB
1. Rear wiper blade 2. Rear wiper arm 3. Rear wiper arm cover
H
Removal and Installation INFOID:0000000001312090
REMOVAL I
1. Operate the rear wiper to the auto stop position.
2. Remove rear wiper arm cover.
3. Remove the rear wiper arm mounting nut. J
4. Raise rear wiper arm, and remove wiper arm from the vehicle.
INSTALLATION K
1. Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
WW
N
SKIA0082J
WW-119
REAR WIPER ARM
< ON-VEHICLE REPAIR >
Adjustment INFOID:0000000001312091
JPLIA0392ZZ
WW-120
REAR WIPER MOTOR
< ON-VEHICLE REPAIR >
REAR WIPER MOTOR
A
Exploded View INFOID:0000000001209007
JPLIA0393ZZ
REMOVAL
1. Remove rear wiper arm cover and rear wiper arm. Refer to WW-119, "Exploded View". I
2. Remove back door trim finisher lower. Refer to INT-31, "Exploded View".
3. Disconnect the rear wiper motor connector.
J
4. Remove bolts.
5. Remove rear wiper motor from the vehicle.
6. Remove pivot seal. K
INSTALLATION
1. Install the pivot seal.
WW
2. Install the rear wiper motor to the vehicle.
3. Connect the rear wiper motor connector.
4. Operate the rear wiper to the auto stop position.
M
5. Install the back door trim finisher lower. Refer to INT-31, "Exploded View".
6. Install rear wiper arm cover and rear wiper arm. Refer to WW-119, "Exploded View".
N
WW-121
REAR WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
REAR WASHER NOZZLE AND TUBE
Exploded View INFOID:0000000001306512
JPLIA0385ZZ
WW-122
REAR WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
Hydraulic Layout INFOID:0000000001209010
WW
JPLIA0386ZZ
M
REMOVAL
1. Remove the back door inner finisher. Refer to INT-31, "Exploded View". P
2. Remove the rear washer tube from the rear washer nozzle.
WW-123
REAR WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
3. Push pawl (A), and remove the rear washer nozzle (1) from the
back door.
JPLIA0387ZZ
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment INFOID:0000000001209012
INSPECTION
Washer Nozzle Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
JPLIA0388ZZ
ADJUSTMENT
Washer Nozzle Spray Position adjustment
Adjust spray positions to match the positions shown in the figure.
JPLIA0389ZZ
Insert a needle or similar object (B) into the spray opening (A) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
JPLIA0390ZZ
WW-124