OL23783
OL23783
OL23783
November 3, 2010
Cisco IOS Release 12.1(22)EA14 runs on Catalyst 2955, Catalyst 2950, and Catalyst 2940 switches.
These release notes include important information about this release and any limitations, restrictions,
and caveats that apply to it. To verify that these release notes are correct for your switch:
• If you are installing a new switch, see the Cisco IOS release label on the rear panel of your switch.
• If your switch is running, you can use the show version user EXEC command. See the “Finding the
Software Version and Feature Set” section on page 7.
• If you are upgrading to a new release, see the software upgrade filename for the Cisco IOS version.
For the complete list of Catalyst 2955, Catalyst 2950, and Catalyst 2940 switch documentation, see the
“Related Documentation” section on page 40.
You can download the switch software from this site (registered Cisco.com users with a login password):
http://www.cisco.com/cisco/web/download/index.html
Contents
• “System Requirements” section on page 2
• “Upgrading the Switch Software” section on page 6
• “Installation Notes” section on page 14
• “New Features” section on page 14
• “Limitations and Restrictions” section on page 15
• “Important Notes” section on page 26
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
System Requirements
System Requirements
• “Hardware Supported” section on page 2
• “Hardware Not Supported” section on page 4
• “Device Manager System Requirements” section on page 4
• “Cluster Compatibility” section on page 5
Hardware Supported
The Catalyst 2950 switch is supported by either the standard software image (SI) or the enhanced
software image (EI). The Catalyst 2950 Long-Reach Ethernet (LRE) and Catalyst 2955 switches are
supported only by the EI. The Catalyst 2940 switch supports some of the features supported by a
Catalyst 2950 switch.
The EI provides a richer set of features, including access control lists (ACLs), enhanced quality of
service (QoS) features, and extended-range VLANs. The cryptographic SI and EI support the Secure
Shell Version 2 (SSHv2) protocol.
For information about the software releases that support the switches listed in Table 1, see the “Catalyst
2950 Hardware and Software Compatibility Matrixes” section on page 24.
Table 1 Catalyst 2940, Catalyst 2950, and Catalyst 2955 Hardware Supported
Software
Hardware Image Description
1
Catalyst 2940-8TT-S – 8 10/100 Ethernet ports and 1 10/100/1000 Ethernet port
1
Catalyst 2940-8TF-S – 8 10/100 Ethernet ports, 1 SFP2 module slot, and 1 100BASE-FX port
Catalyst 2950-12 SI 12 fixed autosensing 10/100 Ethernet ports
Catalyst 2950-24 SI 24 fixed autosensing 10/100 Ethernet ports
Catalyst 2950C-24 EI 24 fixed autosensing 10/100 Ethernet ports and 2 100BASE-FX ports
Catalyst 2950G-12-EI EI 12 fixed autosensing 10/100 Ethernet ports and 2 GBIC3 module slots
Catalyst 2950G-24-EI EI 24 fixed autosensing 10/100 Ethernet ports and 2 GBIC module slots
Catalyst 2950G-24-EI-DC EI 24 fixed autosensing 10/100 Ethernet ports and 2 GBIC module slots with
DC-input power
Catalyst 2950G-48-EI EI 48 fixed autosensing 10/100 Ethernet ports and 2 GBIC module slots
Catalyst 2950ST-8 LRE EI 8 LRE ports, 2 10/100/1000 Ethernet ports4, and 2 SFP module slots
Catalyst 2950ST-24 LRE EI 24 LRE ports, 2 10/100/1000 Ethernet ports4, and 2 SFP module slots
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
2 OL-18328-01
System Requirements
Table 1 Catalyst 2940, Catalyst 2950, and Catalyst 2955 Hardware Supported (continued)
Software
Hardware Image Description
Catalyst 2950ST-24 LRE 997 EI 24 LRE ports, 2 10/100/1000 Ethernet ports4, and 2 SFP module slots with
DC-input power
Catalyst 2950SX-24 SI 24 fixed autosensing 10/100 Ethernet ports and 2 1000BASE-SX ports
Catalyst 2950SX-48-SI SI 48 fixed autosensing10/100 Ethernet ports and 2 1000BASE-SX ports
Catalyst 2950T-24 EI 24 fixed autosensing 10/100 Ethernet ports and 2 10/100/1000 Ethernet ports5
Catalyst 2950T-48-SI SI 48 fixed autosensing 10/100 Ethernet ports and 2 10/100/1000 Ethernet ports
Catalyst 2955C-12 EI 12 fixed autosensing 10/100 ports and 2 MM6 100BASE-FX ports
Catalyst 2955S-12 EI 12 fixed autosensing 10/100 ports and 2 SM7 100BASE-LX ports
Catalyst 2955T-12 EI 12 fixed autosensing 10/100 ports and 2 10/100/1000 Ethernet ports4
1. The Catalyst 2940 switch supports some of the features supported by a Catalyst 2950 switch.
2. SFP = small form-factor pluggable
3. GBIC = Gigabit Interface Converter
4. The 10/100/1000 ports on a Catalyst 2950 LRE or Catalyst 2955T-12 switch operate at 10 or 100 Mbps in either full- or half-duplex mode and at
1000 Mbps only in full-duplex mode.
5. The 10/100/1000 interfaces on the Catalyst 2950T-24 switch do not support the half keyword in the duplex command.
6. MM = multimode
7. SM = single mode
Software
Hardware Image Description
Cisco 575 LRE CPE1 — 1 fixed 10/100 port
Cisco 576 LRE CPE 997 — 1 fixed 10/100 port
Cisco 585 LRE CPE — 4 fixed 10/100 ports
GBIC modules — • 1000BASE-SX GBIC
• 1000BASE-LX/LH GBIC
• 1000BASE-ZX GBIC
• 1000BASE-T GBIC (model WS-5483)
• CWDM2 fiber-optic GBIC3
• DWDM4 fiber-optic GBIC
• GigaStack GBIC
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 3
System Requirements
Software
Hardware Image Description
Redundant power system — • Cisco RPS 300 redundant power system
• Cisco RPS 675 redundant power system
• Cisco RPS 2300 redundant power system
SFP devices — • 1000BASE-SX SFP module
• 1000BASE-LX\LH SFP module
• 1000BASE-ZX SFP module
• 1000BASE-T SFP module
• CWDM
1. CPE = customer premises equipment
2. CDWM = coarse wavelength-division multiplexing
3. This feature is only supported when your switch is running the EI.
4. DWDM = dense wavelength-division multiplexing
Hardware Description
GBIC module 1000BASE-T GBIC (model WS-G4582)
Redundant power system Cisco RPS 600 redundant power system
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
4 OL-18328-01
System Requirements
Hardware Requirements
Software Requirements
These are the supported operating systems and browsers for the device manager:
• Windows 2000, XP, Vista, and Windows Server 2003
• Internet Explorer 5.5, 6.0, 7.0, Firefox 1.5, 2.0 or later
The device manager verifies the browser version when starting a session, and it does not require a
plug-in.
Cluster Compatibility
You cannot create and manage switch clusters through the device manager. To create and manage switch
clusters, use the command-line interface (CLI) or the Network Assistant application.
When creating a switch cluster or adding a switch to a cluster, follow these guidelines:
• When you create a switch cluster, we recommend configuring the highest-end switch in your cluster
as the command switch.
• If you are managing the cluster through Network Assistant, the switch that has the latest software
should be the command switch.
• The standby command switch must be the same type as the command switch. For example, if the
command switch is a Catalyst 3750 switch, all standby command switches must be Catalyst 3750
switches.
For additional information about clustering, see Getting Started with Cisco Network Assistant and
Release Notes for Cisco Network Assistant (not orderable but available on Cisco.com), the software
configuration guide, and the command reference.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 5
Upgrading the Switch Software
Note The Catalyst 2950-12 and Catalyst 2950-24 switches cannot be upgraded to Cisco IOS
Release 12.1(6)EA2, Cisco IOS Release 12.1(6)EA2a, or Cisco IOS Release 12.1(6)EA2b. They can be
upgraded to Cisco IOS Release 12.1(6)EA2c or later.
When you upgrade a switch, the switch continues to operate while the new software is copied to flash
memory. If flash memory has enough space, the new image is copied to the selected switch but does not
replace the running image until you reboot the switch. If a failure occurs during the copy process, you
can still reboot your switch by using the old image. If flash memory does not have enough space for two
images, the new image is copied over the existing one. Features provided by the new software are not
available until you reload the switch.
If a failure occurs while copying a new image to the switch, and the old image has already been deleted,
see the “Recovering from Corrupted Software” section in the “Troubleshooting” chapter of the software
configuration guide for this release.
For information about upgrading the LRE switch firmware, see the “Upgrading LRE Switch Firmware”
section in the software configuration guide for this release.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
6 OL-18328-01
Upgrading the Switch Software
Caution A bootloader upgrade occurs if you are upgrading Catalyst 2950 switches running Cisco IOS
Release 12.1(9)EA1d or earlier to Cisco IOS Release 12.1(11)EA1 or later for both cryptographic and
noncryptographic images.
When you first upgrade the switch from a Cisco IOS noncryptographic image to a cryptographic image,
the bootloader automatically upgrades. The new bootloader upgrade can take up to 30 seconds. Do not
power cycle the switch the first time that you are upgrading the switch to a cryptographic Cisco IOS
image. If a power failure occurs when you are copying this image to the switch, call Cisco Systems
immediately.
Caution Do not power cycle the switch while you are copying an image to the switch. If a power failure occurs
while you are copying the software image to the switch, and there are no other images on the switch, see
the “Troubleshooting” chapter in the software configuration guide for detailed recovery procedures.
Note If you are upgrading a non-LRE Catalyst 2950 switch from a release earlier than Cisco IOS
Release 12.1(6)EA2, use the tar command instead of the archive tar command.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 7
Upgrading the Switch Software
Table 5 Catalyst 2955, 2950, and Catalyst 2940 Cisco IOS Software Files
Filename Description
c2955-i6k2l2q4-tar.121-22.EA14.tar Catalyst 2955 EI files. This includes the cryptographic Cisco IOS image and the
device manager files.
c2955-i6q4l2-tar.121-22.EA14.tar Catalyst 2955 EI files. This includes the Cisco IOS image and the device
manager files.
c2950-i6k2l2q4-tar.121-22.EA14.tar Catalyst 2950 SI1 and EI files. This includes the cryptographic Cisco IOS image
and the device manager files.
c2950-i6q4l2-tar.121-22.EA14.tar Catalyst 2950 SI and EI files. This includes the Cisco IOS image and the device
manager files.
c2950lre-i6k2l2q4-tar.121-22.EA14.tar Catalyst 2950 LRE EI files. This includes the cryptographic Cisco IOS image
and the device manager files.
c2950lre-i6l2q4-tar.121-22.EA14.tar Catalyst 2950 LRE EI files. This includes the Cisco IOS image and the device
manager files.
c2940-i6k2l2q4-tar.121-22.EA14.tar Catalyst 2940 files. This includes the cryptographic Cisco IOS image and the
device manager files.
c2940-i6q4l2-tar.121-22.EA14.tar Catalyst 2940 files. This includes the Cisco IOS image and the device manager
files.
1. Switches that support only the SI cannot run the cryptographic image. For more information, see the SI-only switches listed in Table 1 and the “Cisco
IOS Limitations and Restrictions” section on page 15.
Note Although you can copy any file on the flash memory to the TFTP server, it is time-consuming to copy
all of the HTML files in the tar file. We recommend that you download the tar file from Cisco.com and
archive it on an internal host in your network.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
8 OL-18328-01
Upgrading the Switch Software
You can also configure the switch as a TFTP server to copy files from one switch to another without
using an external TFTP server by using the tftp-server global configuration command. For more
information about the tftp-server command, see the “Additional File Transfer Commands” section of
the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2
http://www.cisco.com/en/US/docs/ios/fundamentals/command/reference/cf_t1.html
Note When using the Network Assistant to upgrade your switch, do not use or close your browser session after
the upgrade process begins. Wait until after the upgrade process completes.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 9
Upgrading the Switch Software
Copying the Current Startup Configuration from the Switch to TFTP Server
When you make changes to a switch configuration, your changes become part of the running
configuration. When you enter the command to save those changes to the startup configuration, the
switch copies the configuration to the config.text file in flash memory. To ensure that you can recreate
the configuration if a switch fails, you might want to copy the config.text file from the switch to a TFTP
server.
Beginning in privileged EXEC mode, follow these steps to copy a switch configuration file to the TFTP
server.
Step 1 Copy the file in flash memory to the root directory of the TFTP server:
switch# copy flash:config.text tftp
Step 2 Enter the IP address of the device where the TFTP server resides:
Address or name of remote host []? ip_address
Step 3 Enter the name of the destination file (for example, config.text):
Destination filename [config.text]? yes/no
Step 4 Verify the copy by displaying the contents of the root directory on the TFTP server.
Using the CLI to Upgrade a Catalyst 2950 LRE or Catalyst 2940 Switch
Use this procedure for upgrading your Catalyst 2950 LRE or Catalyst 2940 switch by using the archive
download-sw privileged EXEC command to automatically extract and download the Cisco IOS image
and the device manager files to the switch. The archive download-sw command initiates this process:
• It verifies adequate space on the flash memory before downloading the new set of images.
• If there is insufficient space on the flash memory to hold both the old and the new images, it deletes
the old set of images. The images are always stored in a subdirectory on the flash memory. The
subdirectory name is the same as the image release name, for example,
flash:/c2940-i6q412-tar.121.22.EA5/
• It replaces the old set of images with the new set of images. The set includes the Cisco IOS image
and the device manager files and, on Catalyst 2950 LRE switches, the LRE firmware files. You do
not have to manually delete the device manager directory from flash memory.
• After the new set of files is downloaded, it automatically sets the BOOT environment variable.
• If you enter the command with the /reload or the /force-reload option, it automatically reloads the
switch after the upgrade.
For further information on this command, see the command reference for this release.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
10 OL-18328-01
Upgrading the Switch Software
Follow these steps to upgrade the switch software by using a TFTP transfer:
Step 1 If your PC or workstation cannot act as a TFTP server, copy the file to a TFTP server to which you have
access.
Step 2 Log into the switch by starting a Telnet session or by connecting to the switch console port through the
RS-232 connector.
To start a Telnet session on your PC or workstation, enter this command:
server% telnet switch_ip_address
For more information about assigning an IP address and default gateway to the switch, see the software
configuration guide for this release.
Step 5 Download the image file from the TFTP server to the switch. If you are installing the same version of
software that is currently on the switch, overwrite the current image by using this privileged EXEC
command:
archive download-sw /overwrite /reload tftp:[[//location]/directory]/image-name.tar
The /overwrite option overwrites the software image in flash memory with the downloaded one.
Note You must use the /overwrite option when upgrading a Catalyst 2940 switch.
The /reload option reloads the system after downloading the image unless the configuration has been
changed and not saved.
For //location, specify the IP address of the TFTP server.
For /directory/image-name.tar, specify the directory (optional) and the image to download. Directory
and image names are case-sensitive.
This example shows how to download an image from a TFTP server at 198.30.20.19 and to overwrite
the image on the switch:
Switch# archive download-sw /overwrite tftp://198.30.20.19/filename.tar
You can also download the image file from the TFTP server to the switch and keep the current image by
replacing the /overwrite option with the /leave-old-sw option.
Your Telnet session ends when the switch reloads.
After the switch reboots, use Telnet to return to the switch, and enter the show version user EXEC
command to verify the upgrade procedure. If you have a previously opened browser session to the
upgraded switch, close the browser, and start it again to ensure that you are using the latest HTML files.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 11
Upgrading the Switch Software
Using the CLI to Upgrade a Catalyst 2955 Switch or Non-LRE Catalyst 2950 Switch
Use this procedure for upgrading your Catalyst 2955 or non-LRE Catalyst 2950 switch by copying the
tar file to the switch. You copy the Cisco IOS image and the device manager files to the switch from a
TFTP server and then extract the files by entering the archive tar command, with these results:
• Changes the name of the current image file to the name of the new file that you are copying and
replaces the old image file with the new one. Perform this step only if you have space available on
your switch.
• Disables access to the device manager pages and deletes the existing device manager files before the
software upgrade to avoid a conflict if users access the web pages during the software upgrade.
• Re-enables access to the device manager pages after the upgrade is complete.
Caution A bootloader upgrade occurs if you are upgrading Catalyst 2950 switches running Cisco IOS
Release 12.1(9)EA1d or earlier to Cisco IOS Release 12.1(11)EA1 or later for both cryptographic and
noncryptographic images.
When you first upgrade the switch from a Cisco IOS noncryptographic image to a cryptographic image,
the bootloader automatically upgrades. The new bootloader upgrade can take up to 30 seconds. Do not
power cycle the switch the first time that you are upgrading the switch to a cryptographic Cisco IOS
image. If a power failure occurs when you are copying this image to the switch, call Cisco Systems
immediately.
Before downloading the new image, use the dir user EXEC command to confirm that you have enough
space on the flash. The new image and HTML files will be slightly larger than the size of the tar file.
If you do not have enough space on the flash for the tar file, delete any old unused Cisco IOS images. If
that does not free up enough flash space, delete the HTML files.
Caution Do not delete the image that you are currently running on the switch. If the switch fails while
downloading the new image, you will need to use this.Follow these steps to upgrade the switch software
by using a TFTP transfer:
Step 1 If your PC or workstation cannot act as a TFTP server, copy the file to a TFTP server to which you have
access.
Step 2 Log into the switch by starting a Telnet session or by connecting to the switch console port through the
RS-232 connector.
To start a Telnet session on your PC or workstation, enter this command:
server% telnet switch_ip_address
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
12 OL-18328-01
Upgrading the Switch Software
where /r is for /recursive and /f is for /force. This command deletes all the switch HTML files and
subdirectories.
Press Enter to confirm the deletion of each file. Do not press any other keys during this process.
Note If you deleted unused Cisco IOS images and switch HTML files from the flash memory and there is still
do not sufficient space to download the tar file, delete other unused files, such as files containing failure
information. When deleting files, be careful not to delete the image running on the switch. If the software
upgrade fails, the switch uses that image to reboot.
Step 5 Enter this command to copy the new image and the device manager files to flash memory:
Caution In this step, the archive tar command copies the tar file that contains both the image and the device
manager files. If you are upgrading from a release earlier than Cisco IOS Release 12.1(6)EA2, use the
tar command instead of the archive tar command.
Depending on the TFTP server being used, you might need to enter only one slash (/) after the
server_ip_address in the archive tar command.
Step 6 Display the name of the running (default) image file (BOOT path-list). This example shows the name in
italic:
switch# show boot
BOOT path-list: flash:current_image
Config file: flash:config.text
Enable Break: 1
Manual Boot: no
HELPER path-list:
NVRAM/Config file
buffer size: 32768
Step 8 Enter the boot command with the name of the new image filename:
switch(config)# boot system flash:new_image
For example:
switch(config)# boot system flash:filename.bin
Note If the show boot command entered in Step 6 displays no image name, you do not need to enter this
command; the switch automatically finds the correct file to use when it resets.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 13
Installation Notes
Installation Notes
You can assign IP information to your switch by using one of these methods:
• The Express Setup program on Catalyst 2950 (including Catalyst 2950 LRE switches) and
Catalyst 2940 switches. The Express Setup program is not supported on Catalyst 2955 switches.
For more information about Express Setup, see the “Quick Setup” chapter in the Catalyst 2950 and
Catalyst 2940 getting started guides.
• The CLI-based setup program.
This procedure is described in the Catalyst 2955, Catalyst 2950, and Catalyst 2940 hardware
installation guides.
• The DHCP-based autoconfiguration. See the software configuration guide for your switch.
• Manually assigning an IP address. See the software configuration guide for your switch.
New Features
• “New Hardware Features” section on page 14
• “New Software Features” section on page 15
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
14 OL-18328-01
Limitations and Restrictions
Note These limitations and restrictions apply to all Catalyst 2955, Catalyst 2950, and Catalyst 2940 switches
unless otherwise noted.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 15
Limitations and Restrictions
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
16 OL-18328-01
Limitations and Restrictions
• There might be a link on the Fast Ethernet port of the Catalyst 2950 switch when it is forced to
10 Mbps and full-duplex mode and its link partner is forced to 100 Mbps and forced duplex mode.
The LED on the Catalyst 2950 switch might display the link, and the error counters might increment.
The workaround is to configure both sides of a link to the same speed or use autonegotiation.
(CSCdv62271)
• The ip http authentication enable global configuration command is not saved to the configuration
file because this is the default configuration. Therefore, this configuration is lost after a reboot.
The workaround is to manually enter the command again after a reboot. (CSCdv67047)
• If a stack that has Catalyst 2955, Catalyst 2950, or Catalyst 2940 switches also has Catalyst 2900 XL
or Catalyst 3500 XL switches, cross-stack UplinkFast (CSUF) does not function if the management
VLAN on the Catalyst 2900 XL or Catalyst 3500 XL switches is changed to a VLAN other than
VLAN 1 (the default).
The workaround is to make sure that the management VLANs of all Catalyst 2900 XL or 3500 XL
switches in the stack are set to VLAN 1. (CSCdv82224)
• If a port is configured as a secure port with the violation mode as restrict, the secure ports might
process packets even after maximum limit of MAC addresses is reached, but those packets are not
forwarded to other ports. (CSCdw02638)
• The discarded frames count of the show controllers ethernet-controller privileged EXEC
command output and the ignored count of the show controller ethernet privileged EXEC command
output can increment for these reasons:
– The source and destination ports are the same.
– The spanning-tree state of the ingress port is not in the forwarding state.
– Traffic is filtered because of unicast or multicast storms are on the port.
– Traffic is dropped because a VLAN has not been assigned by VLAN Query Protocol (VQP).
Note This error occurs only on switches that can run Cisco IOS Release 12.0(5)WC2b or earlier.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 17
Limitations and Restrictions
The workaround is to check your switch configuration and ensure that it meets the previous
conditions. (CSCdw66805)
• When you use the policy-map global configuration command to create a policy map, and you do not
specify any action for a class map, the association between that class map and policy map is not
saved when you exit policy-map configuration mode.
The workaround is to specify an action in the policy map. (CSCdx75308)
• When a community string is assigned by the cluster command switch, you cannot get any
dot1dBridge MIB objects by using a community string with a VLAN entity from a cluster member
switch.
The workaround is to manually add the cluster community string with the VLAN entity on the
member switches for all active VLANs shown in the show spanning-tree summary display. This
is an example of such a change, where cluster member 3 has spanning tree on vlan 1-3, and the
cluster commander community string is public@es3.
Switch(config)# snmp community public@es3@1 RO
Switch(config)# snmp community public@es3@2 RO
Switch(config)# snmp community public@es3@3 RO
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
18 OL-18328-01
Limitations and Restrictions
• When you configure a dynamic switch port by using the switchport access vlan dynamic interface
configuration command, the port might allow unauthorized users to access network resources if the
interface changes from access mode to trunk mode through Dynamic Trunking Protocol (DTP)
negotiation.
The workaround is to configure the port as a static access port. (CSCdz32556)
• The output from the show stack privileged EXEC command might show a large number of false
interrupts.
There is no workaround. The number of interrupts does not affect the switch functionality.
(CSCdz34545)
• If you configure a static secure MAC address on an interface before enabling port security on the
interface, the same MAC address is allowed on multiple interfaces. If the same MAC address is
added on multiple ports before enabling port security and port security is later enabled on those
ports, only the first MAC address can be added to the hardware database. If port security is first
enabled on the interface, the same static MAC address is not allowed on multiple interfaces.
(CSCdz74685)
• In Cisco IOS Release 12.1(13)EA1 or later, these are the default settings for a IP Phone connected
to a switch:
– The port trust state is to not trust the priority of frames arriving on the IP Phone port from
connected devices.
– The class of service (CoS) value of incoming traffic is overwritten and set to zero.
(CSCdz76915)
• If you press and hold the spacebar while the output of any show user EXEC command is being
displayed, the Telnet session is stopped, and you can no longer communicate with the management
VLAN.
These are the workarounds:
– Enter the show commands from privileged EXEC mode, and use this command to set the
terminal length to zero:
switch# terminal length 0
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 19
Limitations and Restrictions
• When a 10/100 switch port is connected to a 10/00 port on a hub and another 10/100 port on the hub
is connected to a 10/100 port on another switch, when one of the switches restarts, the link state
might change from down to up, and these messages might appear:
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Then the switch that restarted does not forward traffic until the spanning-tree state enters the
forwarding state. This can occur on a switch running Cisco IOS Release 12.1(13)EA1 or later.
(CSCea47230)
• On a Catalyst 2940 switch, when a 1000BASE-T SFP module is inserted in the SFP module slot, the
output of the show interface capabilities privileged EXEC command incorrectly shows that the
interface supports 10 Mbps, 100 Mbps, and 1000 Mbps. The SFP module supports only 1000 Mbps.
(CSCeb31239)
• After a topology change in STP, some terminals connected to the management VLAN can transfer
data because the affected switch ports start forwarding before they move to the forwarding state.
Note If the terminal does not belong to management VLAN, this failure does not occur.
The workaround is to place the ports in static-access mode for a single VLAN, if the topology
supports this configuration. (CSCec13986)
• (Catalyst 2950 switches) If a policy map is applied to a switch, it might be only partially applied on
these ingress ports; Fast Ethernet 0/8, Fast Ethernet 0/16, Fast Ethernet 0/24, Fast Ethernet 0/32, Fast
Ethernet 0/40, or Fast Ethernet 0/48.
This problem occurs when:
– All eight ports of a port group are configured to trust Differentiated Services Code Point
(DSCP). A port group can have Fast Ethernet ports 1 to 8, 9 to 16, and so on.
– A policy map is applied.
– A port group has 75 or more access control entries (ACEs).
The workaround is to use fewer than 75 ACEs per port group when configuring the ports to trust
DSCP. (CSCed11617)
• When connected to some third-party devices that send early preambles, a switch port operating at
100 Mbps full duplex or 100 Mbps half duplex might bounce the line protocol up and down. The
problem is seen only when the switch is receiving frames.
The workaround is to configure the port for 10 Mbps and half duplex or to connect a hub or a
nonaffected device to the switch. (CSCed39091)
• If a switch receives STP packets and non-STP packets that have a CoS value of 6 or 7 and all of these
packets belong to the same management VLAN, a loop might occur.
These are the workarounds:
– Change the CoS value of the non-STP packets to a value other than 6 or 7.
– If the CoS value of the non-STP packets must be 6 or 7, configure these packets to belong to a
VLAN other than the management VLAN. (CSCed88622)
• This problem can affect switches running Cisco IOS Release 12.1(22)EA4. The EtherChannel
between two switches flaps, and this message appears:
ERROR interrupt: PCI Fatal Error on DMA CH0
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
20 OL-18328-01
Limitations and Restrictions
This problem occurs when there is an EtherChannel between two switches, traffic is sent between
the switches, and the RSPAN or SPAN source port is configured to monitor sent traffic.
The workaround is to stop the SPAN traffic, and then delete and recreate the VLAN. (CSCeh20389)
• When the switch is fast aging MAC addresses or learning MAC addresses at an extremely high rate,
frames are lost for about one or two seconds when the switch is updating the MAC address table.
A Topology Change Notification (TCN) can contribute to the occurrence of this symptom.
The workaround to reduce unnecessary TCNs is to use the spanning-tree portfast [trunk] interface
configuration command to configure Port Fast on all switch ports in the entire VLAN that are
connected to end-stations. (CSCei63842)
• CSCsd43109 (Catalyst 2950SX-48-SI, 2950G-24-EI, and 2950T-48-SI switches)
When two Catalyst 2950SX-48-SI, 2950G-24-EI, or 2950T-48-SI switches are connected back to
back, and both sides of the link change from 100 Mbps half duplex to 10 Mbps half duplex, only one
side of the link becomes error disabled. This error message appears:
Nov 22 19:03:10: %ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD: Half-duplex loopback
detected, collision threshold exceeded on FastEthernet0/24.
Nov 22 19:03:10: %PM-4-ERR_DISABLE: loopback error detected on Fa0/24, putting Fa0/24
in err-disable state
Nov 22 19:03:11: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24,
changed state to down
Nov 22 19:03:12: %LINK-3-UPDOWN: Interface FastEthernet0/24, changed state to down
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 21
Limitations and Restrictions
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
22 OL-18328-01
Limitations and Restrictions
• The Cisco 585 LRE CPE has four Fast Ethernet ports. When the CPE is connected to an LRE switch,
the default value for the maximum number of secure MAC addresses is 1. You can use the show
port-security command to display the current maximum value.
The workaround is to use the switchport port-security maximum value interface configuration
command to change the default value. For interfaces connected to Cisco 575 LRE and Cisco 576
LRE 997 CPEs, the default value can be 1. For interfaces connected to Cisco 585 LRE CPEs, the
value can be 5 because the CPE has four Fast Ethernet ports and one additional MAC address.
(CSCdy73748)
• The Cisco 575 LRE or the Cisco 576 LRE 997 CPE does not support all of the Fast Ethernet statistics
displayed by the show controllers ethernet-controller longreachethernet interface-id cpe
command. The Cisco 585 LRE CPE supports all the LRE and CPE Fast Ethernet statistics.
There is no workaround. These CPE Fast Ethernet statistics are supported by the Cisco 575 LRE
CPE and the Cisco 576 LRE 997 CPE (CSCdy89348):
1 Transmit receive 0 bytes
0 Bytes
0 Unicast frames
0 Broadcast frames
0 Pause frames
0 Alignment errors
0 One collision frames
0 Multiple collisions
0 Undersize frames
0 Late collisions
0 Oversize frames
0 Excess collisions
0 FCS errors
0 Deferred frames
• When the entPhysicalTable object is retrieved, the copper physical entry is not included.
There is no workaround. (CSCdz06748)
• When an IEEE 802.1x protocol-enabled client attempts to connect to a Catalyst 2950 LRE switch
through a Cisco 585 LRE CPE with IEEE 802.1x configured on a port, the client cannot be
authenticated. This problem does not affect the Cisco 575 LRE CPE or the Cisco 576 LRE 997 CPE.
The show dot1x interface interface configuration command displays the port state as unauthorized.
(CSCdz22965)
• When a Fast Ethernet port on a Cisco 585 LRE CPE is in half-duplex mode and the rate at which the
port receives packets is higher than rate at which it can forward packets, the Pause Frames counter
for the CPE port increments.
There is no workaround. (CSCea41362)
• On a Catalyst 2950 LRE switch running Cisco IOS Release 12.1(11)YJ4 or later, a Cisco 575 LRE
CPE or a Cisco 576 LRE 997 CPE that does not have an LRE link but is connected to a remote device
through the Ethernet link might see repeated flaps on the Ethernet link. This does not occur on a
Cisco 585 LRE CPE. (CSCeb01097)
• When a Cisco Catalyst 2950 LRE running Cisco IOS 12.1(14)EA1 or Cisco IOS 12.1(11)YJ is
connected to Cisco 575 LRE CPE, the Fast Ethernet link on the CPE port fails to activate if you
change the CPE speed setting from 10 to 100 Mbps while the CPE duplex mode is set to half or full.
The workaround is to reset the CPE port by using the cpe shutdown followed by the no cpe
shutdown interface configuration command. This activates the Fast Ethernet link on the CPE port.
(CSCeb35007)
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 23
Limitations and Restrictions
• When you shut down the 100BASE-FX port on the Catalyst 2950 switch, the upstream switch does
not detect loss of link, and the line protocol stays up.
Configure UDLD aggressive mode (using the udld port aggressive interface configuration
command) on both the Catalyst switch and neighboring device, and change the error- disable
recovery options by using the errdisable recovery cause udld and errdisable recovery interval 60
global configuration commands. (CSCee57059)
• On a Catalyst 2950 LRE switch running Cisco IOS Release 12.1(20)EA1 or later, the flowcontrol
interface configuration commands only take effect when the LRE link comes up after being shut
down.
If the switch configuration is saved and the switch restarts, this does not affect the switch. However,
if the flow control configuration for an LRE port is changed and the switch is not rebooted, the
commands do not take effect unless you shut down and bring up the LRE link.
The workaround is to enter the shutdown and no shutdown interface configuration commands on
an interface after entering a flowcontrol interface configuration command, such as the flowcontrol
receive or the flowcontrol send command. (CSCef26565)
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
24 OL-18328-01
Limitations and Restrictions
Cisco IOS
Cisco IOS Release 12.1(6)EA2, Cisco IOS
Release 12.0(5)WC2b 12.1(6)EA2a, and Cisco IOS Release 12.1(9)EA1
Hardware Serial Number or Earlier 12.1(6)EA2b Release 12.1(6)EA2c or Later
Catalyst Any serial number Yes No Yes Yes
2950-12 beginning with FAA or
FAB
Lower than Yes No Yes Yes
FOC0616W1H6 or
FHK0616W34M
FOC0616W1H6, No No Yes Yes
FHK0616W34M, or
higher
Catalyst Any serial number Yes No Yes Yes
2950-24 beginning with FAA or
FAB
Lower than Yes No Yes Yes
FOC0616Z1ZM or
FHK0617Y0N3
FOC0616Z1ZM, No No Yes Yes
FHK0617Y0N3,
or higher
Catalyst Any serial number Yes Yes Yes Yes
2950C-24 beginning with FAA or
FAB
Lower than Yes Yes Yes Yes
FOC0616TOJH or
FHK0617W0YA
FOC0616TOJH, No No Yes Yes
FHK0617W0YA,
or higher
Catalyst Any serial number Yes Yes Yes Yes
2950T-24 beginning with FAA or
FAB
Lower than Yes Yes Yes Yes
FOC0617X11P or
FHK0617Y1M2
FOC0617X11P, No No Yes Yes
FHK0617Y1M2,
or higher
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 25
Important Notes
The Cisco LRE CPE devices are not supported by certain Catalyst 2950 LRE switches. In Table 8, Yes
means that the CPE is supported by the switch; No means that the CPE is not supported by the switch.
Important Notes
Note These important notes apply to all Catalyst 2955, Catalyst 2950, and Catalyst 2940 switches unless
otherwise noted.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
26 OL-18328-01
Important Notes
• When an IEEE 802.1x-authenticated client is disconnected from an IP phone, hub, or switch and
does not send an EAPOL-Logoff message, the switch interface does not change to the unauthorized
state. If this happens, it can take up to 60 minutes for the interface to change to the unauthorized
state when the re-authentication time is the default value (3600 seconds).
The workaround is to change the number of seconds between re-authentication attempts by using
the dot1x timeout re-authperiod seconds global configuration command. (CSCdz38483)
• The guest VLAN might not assign a DHCP address to some clients. This is a problem with the IEEE
802.1x client, not with the switch.
The workaround is to either release and renew the IP address or to change the default timers. These
examples show typical interface timer changes:
dot1x timeout quiet-period 3
dot1x timeout tx-period 5
• The transmit-interface type number interface configuration command is not supported.
• If the switch requests information from the Cisco Secure Access Control Server (ACS) and the
message exchange times out because the server does not respond, a message similar to this appears:
00:02:57: %RADIUS-4-RADIUS_DEAD: RADIUS server 172.20.246.206:1645,1646 is not
responding.
If this message appears, check that there is network connectivity between the switch and the ACS.
You should also check that the switch has been properly configured as an AAA client on the ACS.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 27
Open Caveats
Beginning in privileged EXEC mode, follow these steps to configure the HTTP server interface:
Command Purpose
Step 1 configure terminal Enter global configuration mode.
Step 2 ip http authentication {enable | local | Configure the HTTP server interface for the type of authentication that
tacacs} you want to use.
• enable—Enable password, the default method of HTTP server user
authentication.
• local—Local user database, as defined on the Cisco router or access
server.
• tacacs—TACACS server.
Step 3 end Return to privileged EXEC mode.
Step 4 show running-config Verify your entries.
• The device manager uses the HTTP protocol (the default is port 80) and the default method of
authentication (the enable password) to communicate with the switch through any of its Ethernet
ports and to allow switch management from a standard web browser.
If you change the HTTP port, you must include the new port number when you enter the IP address
in the browser Location or Address field (for example, http://10.1.126.45:184, where 184 is the new
HTTP port number). You should write down the port number through which you are connected. Use
care when changing the switch IP information.
• If you use Internet Explorer Version 5.5 and select a URL with a nonstandard port at the end of the
address (for example, www.cisco.com:84), you must enter http:// as the URL prefix. Otherwise, you
cannot launch the device manager.
Open Caveats
Unless otherwise noted, these severity 3 Cisco IOS configuration caveats apply to the Catalyst 2955,
2950, and 2940 switches.
There are no open caveats for this release.
Resolved Caveats
• CSCsx09522
For a short period of time, the number of discards from the ifInDiscards instance for an interface is
different from the VLAN discard frames counter in the show controllers ethernet-controller
interface-id privileged EXEC command output.
There is no workaround.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
28 OL-18328-01
Resolved Caveats
• CSCsx74672
When the Cisco Access Control Server (ACS) application is unreachable and a host is trying to
authenticate, this traceback appears:
%AAAA-3-BADSTR: Bad accounting data: bad pointer
There is no workaround.
• CSCta96418
When a switch port has this configuration:
– The speed is manually set.
– Storm control is configured with the falling threshold of 0.00 and the action is to error disable
the port when a storm is detected.
The switch does not take the configured action after
– A multicast or unicast storm occurs on the port
or
– The switch error disables the port during a storm and you enter the shutdown interface
configuration command followed by the no shutdown interface configuration command to
restart the port.
Use this workaround:
1. Set the falling threshold to a value greater than 0.00.
2. Use the speed auto interface configuration command to enable the interface to autonegotiate
speed with the connected device.
• CSCtb60011
When the switch drops frames because of over-subscription and this information is incorrect:
– The VLAN discard frames counter in the show controllers ethernet-controller privileged
EXEC command output.
– The no buffer or ignored counter in the show interfaces privileged EXEC command output.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 29
Documentation Updates
The Rev-Err counter in the show interfaces counters errors privileged EXEC command output is
also incorrect.
There is no workaround. This does not affect the switch functionality.
• CSCtf89806
If a client was authorized with MAC authentication bypass and is then re-authenticated with
IEEE 802.1x, the switch does not the send the client an EAP-success message.
Use this workaround:
1. Enter the shutdown interface configuration command followed by the no shutdown interface
configuration command to restart the port.
2. Disable MAC authentication bypass on the port, and configure the switch to use IEEE 802.1x
authentication on the port.
• CSCtg49995
A switch can stop and then restart when at least three personal computers are connected to switch
ports and IEEE 802.1x authentication is enabled on the switch with this configuration
<output truncated>
dot1x port-control auto
dot1x timeout quiet-period 1
dot1x timeout tx-period 1
dot1x timeout reauth-period 64800
dot1x timeout supp-timeout 1
dot1x timeout server-timeout 1
dot1x reauthentication
<output truncated>
The workaround is to connect each personal computer to a port after the switch restarts.
Documentation Updates
For updates to the software documentation, see the software configuration guide, command reference,
and system message guide for Cisco IOS Release 12.1(22)EA11 and later. Also see the latest version of
the Regulatory Compliance and Safety Information for the Catalyst 2950 and 2940 switches.
These are the updates to other product documentation:
• “Updates to the Software Configuration Guides” section on page 30
• “Update to the Catalyst 2955 Hardware Installation Guide” section on page 31
• “Updates for the Catalyst 2950 Hardware Installation Guide” section on page 32
• “Updates for the Catalyst 2940 Hardware Installation Guide” section on page 32
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
30 OL-18328-01
Documentation Updates
Note You can order replacement power-and-relay connectors in packages of ten from Cisco by using
part number PWR-2955-CONNECT= .
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 31
Documentation Updates
If all LEDs on a Catalyst 2950-24, 2950C-24, 2950SX-24, and 2950T-24 2950-12 switch are green (no
amber showing), the switch is using 50 percent or more of the total bandwidth. If the far-right LED is
off, the switch is using more than 25 but less than 50 percent of the total bandwidth, and so on. If only
the far-left LED is green, the switch is using less than 0.0488 percent of the total bandwidth.
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.
Statement 1006
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
32 OL-18328-01
Documentation Updates
Step 2 Insert a number-8 Phillips flat-head screw through the bracket into one side of the switch. Tighten the
screw with a screwdriver. Repeat on the opposite side.
Step 3 Align the switch bracket assembly in the rack. Insert the number-12 Phillips machine screws through the
bracket into the rack. Tighten the screws with a screwdriver. Repeat on the opposite side.
Step 4 Use the black Phillips machine screw to attach the cable guide to either bracket.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 33
Documentation Updates
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to
ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in
the rack.
Waarschuwing Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een
servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel
stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren:
• Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is.
• Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van onderen naar boven te laden
met het zwaarste onderdeel onderaan in het rek.
• Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te monteren voordat u het
toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä, on noudatettava erityisiä
varotoimia järjestelmän vakavuuden säilyttämiseksi, jotta vältytään loukkaantumiselta. Noudata
seuraavia turvallisuusohjeita:
Attention Pour éviter toute blessure corporelle pendant les opérations de montage ou de réparation de cette
unité en casier, il convient de prendre des précautions spéciales afin de maintenir la stabilité du
système. Les directives ci-dessous sont destinées à assurer la protection du personnelþ:
• Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le bas.
• Si cette unité est montée dans un casier partiellement rempli, charger le casier de bas en haut en plaçant
l'élément le plus lourd dans le bas.
• Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs avant de monter ou de réparer
l'unité en casier.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
34 OL-18328-01
Documentation Updates
Warnung Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell
müssen Sie besondere Vorkehrungen treffen, um sicherzustellen, daß das System stabil bleibt. Die
folgenden Richtlinien sollen zur Gewährleistung Ihrer Sicherheit dienen:
• Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht werden.
• Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das Gestell von unten nach oben zu laden,
wobei das schwerste Bauteil unten im Gestell anzubringen ist.
• Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die Stabilisatoren zu installieren, bevor Sie
die Einheit im Gestell anbringen oder sie warten.
Avvertenza Per evitare infortuni fisici durante il montaggio o la manutenzione di questa unità in un supporto,
occorre osservare speciali precauzioni per garantire che il sistema rimanga stabile. Le seguenti
direttive vengono fornite per garantire la sicurezza personale:
• Questa unità deve venire montata sul fondo del supporto, se si tratta dell’unica unità da montare nel supporto.
• Quando questa unità viene montata in un supporto parzialmente pieno, caricare il supporto dal basso all’alto,
con il componente più pesante sistemato sul fondo del supporto.
• Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi prima di montare o di procedere alla
manutenzione dell’unità nel supporto.
Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne enheten når den befinner
seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende retningslinjer er gitt for å verne
om sikkerheten:
• Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste enheten i kabinettet.
• Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes fra bunnen og opp med
den tyngste komponenten nederst i kabinettet.
• Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres før montering eller utføring
av reparasjonsarbeid på enheten i kabinettet.
Aviso Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante, deverá
tomar precauções especiais para se certificar de que o sistema possui um suporte estável. As
seguintes directrizes ajudá-lo-ão a efectuar o seu trabalho com segurança:
• Esta unidade deverá ser montada na parte inferior da estante, caso seja esta a única unidade a ser montada.
• Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais pesados na parte inferior
da estante, arrumando-os de baixo para cima.
• Se a estante possuir um dispositivo de estabilização, instale-o antes de montar ou reparar a unidade.
¡Advertencia! Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente durante
su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable. Para
garantizar su seguridad, proceda según las siguientes instrucciones:
• Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad en el mismo.
• Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar la instalación desde la
parte inferior hacia la superior colocando el equipo más pesado en la parte inferior.
• Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes de montar o proceder al
mantenimiento del equipo instalado en el bastidor.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 35
Documentation Updates
Varning! För att undvika kroppsskada när du installerar eller utför underhållsarbete på denna enhet på en
ställning måste du vidta särskilda försiktighetsåtgärder för att försäkra dig om att systemet står
stadigt. Följande riktlinjer ges för att trygga din säkerhet:
• Om denna enhet är den enda enheten på ställningen skall den installeras längst ned på ställningen.
• Om denna enhet installeras på en delvis fylld ställning skall ställningen fyllas nedifrån och upp, med de tyngsta
enheterna längst ned på ställningen.
• Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast innan enheten installeras eller
underhålls på ställningen.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
36 OL-18328-01
Documentation Updates
Aviso Para evitar lesões corporais ao montar ou dar manutenção a esta unidade em um rack, é necessário
tomar todas as precauções para garantir a estabilidade do sistema. As seguintes orientações são
fornecidas para garantir a sua segurança:
• Se esta for a única unidade, ela deverá ser montada na parte inferior do rack.
• Ao montar esta unidade em um rack parcialmente preenchido, carregue-o de baixo para cima com o
componente mais pesado em sua parte inferior.
• Se o rack contiver dispositivos estabilizadores, instale-os antes de montar ou dar manutenção à unidade
existente.
Advarsel For at forhindre legemesbeskadigelse ved montering eller service af denne enhed i et rack, skal du
sikre at systemet står stabilt. Følgende retningslinjer er også for din sikkerheds skyld:
• Enheden skal monteres i bunden af dit rack, hvis det er den eneste enhed i racket.
• Ved montering af denne enhed i et delvist fyldt rack, skal enhederne installeres fra bunden og opad med den
tungeste enhed nederst.
• Hvis racket leveres med stabiliseringsenheder, skal disse installeres for enheden monteres eller serviceres i
racket.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 37
Documentation Updates
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
38 OL-18328-01
Documentation Updates
• The “Connectors and Cables” appendix incorrectly refers to a crossover cable as a rollover cable.
This is the correct information:
You can identify a crossover cable by comparing the two modular cable ends. Hold the cable ends
side-by-side, with the tab at the back, right plug, as shown in Figure 2.
1 Pin 1
2 Pin 9
On a crossover cable, the wire connected to the pin on the outside of the left plug should be the same
color as the wire connected to the pin on the outside of the right plug.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 39
Related Documentation
Related Documentation
You can find complete information about these Catalyst switches on Cisco.com:
• Catalyst 2955 switch
http://www.cisco.com/en/US/products/ps6738/tsd_products_support_series_home.html
• Catalyst 2950 switch
http://www.cisco.com/en/US/products/hw/switches/ps628/tsd_products_support_series_home.
html
• Catalyst 2950 LRE switch
http://www.cisco.com/en/US/products/hw/switches/ps4916/tsd_products_support_series_home.
html
• Catalyst 2950 switch
http://www.cisco.com/en/US/products/hw/switches/ps5213/tsd_products_support_series_home.
html
This document provides information about the Catalyst 2955, Catalyst 2950, and Catalyst 2940
switches:
• Catalyst 2955, 2950, and 2940 Switch System Message Guide
These publications provide more information about the Catalyst 2955 and Catalyst 2950 switches:
• Catalyst 2950 and Catalyst 2955 Switch Software Configuration Guide
• Catalyst 2950 and Catalyst 2955 Switch Command Reference
• Catalyst 2950 Switch Hardware Installation Guide
• Catalyst 2950 Switch Getting Started Guide
• Regulatory Compliance and Safety Information for the Catalyst 2950 Switch
• Catalyst 2955 Hardware Installation Guide
These publications provide more information about the Catalyst 2940 switches:
• Catalyst 2940 Switch Software Configuration Guide
• Catalyst 2940 Switch Command Reference
• Catalyst 2940 Switch Hardware Installation Guide
• Catalyst 2940 Switch Getting Started Guide
• Regulatory Compliance and Safety Information for the Catalyst 2940 Switch
For other information about related products, see these documents:
• Getting Started with Cisco Network Assistant
• Release Notes for Cisco Network Assistant
• 1000BASE-T Gigabit Interface Converter Installation Notes
• Catalyst GigaStack Gigabit Interface Converter Hardware Installation Guide
• Cisco LRE CPE Hardware Installation Guide
• CWDM Passive Optical System Installation Note
• Installation Notes for the Catalyst Family Small-Form-Factor Pluggable Modules
• Installation and Warranty Notes for the Cisco LRE 48 POTS Splitter
• Network Admission Control Software Configuration Guide
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
40 OL-18328-01
Obtaining Documentation and Submitting a Service Request
• These compatibility matrix documents are available from this Cisco.com site:
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.
html
– Cisco Gigabit Ethernet Transceiver Modules Compatibility Matrix
– Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix
– Cisco Small Form-Factor Pluggable Modules Compatibility Matrix
– Compatibility Matrix for 1000BASE-T Small Form-Factor Pluggable Modules)
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks
can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and
figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and
coincidental.
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
OL-18328-01 41
Obtaining Documentation and Submitting a Service Request
Release Notes for the Catalyst 2955, Catalyst 2950, and Catalyst 2940 Switches, Cisco IOS Release 12.1(22)EA14
42 OL-18328-01