01 102 16PCD BELLEVILLE SPRING

MS WASHER OR SPRING
ALU/MS M4 WAVE WASHER
R17.5
02 5
45° 07
45° 3

3x8DP
3x8DP
4 4OFF

1
9

51
05
MS

22
7.5

R2.5
R2.5
3

8
22
12.5 12.5
07

52.5

54
5

27
16PCD
3 3

51
08 8.5PF
17.5 47.5 6.5RM
26
M4 M4
06
08

9
9.5

10

10
06 3

6.5

6.5
06 M4

1
8 8

30
04 5 5

10
02 22 22

5
01 03 67.5 7 4OFF 32 32
SCALE 1:1.5 5
34
35 06 60°
MS 27 60°
16PCD 10 4 PRESS FIT
03 S/S 04
M4 8 MS
08

R2.

.5
07 BRZ

R2

6.5
5

R4
M4

.5
12.5
3

34

°
90
MS

27
12.5
QTY. PART NUMBER
1 ELBOW-01-BASE PLATE
1 ELBOW-02-FLYWHEEL STAND BRZ

M4
1 ELBOW-03-PORT BLOCK 6.5
1 ELBOW-04-REVOLVING CYLINDER BODY 45° BRZ
1 ELBOW-05-FLYWHEEL WITH CYLINDERS 45° 8
3 ELBOW-06-PISTON 100
2 ELBOW-07-SPRING WAVE WASHER 80 26
2 ELBOW-08-CYLINDER SHAFT
4 ELBOW-M4x12 A-K CYL HEAD SCREW MATERIAL ABBREVIATIONS: 55PCD 19
ALU = ALUMINIUM
BRZ = BRONZE OR GUNMETAL (BRZ/GM) 7 HOLES 21 1 1
MS = MILD STEEL/BRIGHT MILD STEEL EQUALLY
S/S = SILVER STEEL OR STAINLESS STEEL SPACED
BRZ ON PCD
OTHER ABBREVIATIONS REFER TO 04
DP = DEEP FOR MORE
ROTATION DIRECTION PF = PRESS FIT DETAILS
PCD = PITCH CIRCLE DIAMETER 7.5 7.5
RM = REAM 05
NOTES:

30
0. THE DRAWING IS IN METRIC MEASUREMENTS

5
1. ALL ENGINEERING PRACTICES SHALL BE APPLIED WITH
REGARDS TO HOLE AND SHAFT TOLERANCES.
2. WHERE SCREWS OR BOLTS ARE USED THE CLEARANCE
HOLES SHALL BE APPROXIMATELY 5% TO 8% LARGER THAN
THE MATCHING TAPPED HOLE. 3.5
3. PREFERABLY ALL TAPPED HOLES AND MATCHING SCREWS
AND/OR BOLTS TO BE METRIC FINE (MF)
4. MATERIALS SPECIFIED ON THE DRAWINGS ARE INDICATIVE
ONLY. THE BUILDER CAN MAKE HIS/HER OWN MATERIAL CHOICE.
5. PARTS WHICH ARE DIRECTLY EXPOSED TO STEAM AND/OR SCALE 1:1.5
WATER SHOULD BE CONSTRUCTED USING NON-FERROUS OR
NON CORROSIVE MATERIAL SUCH AS BRASS, BRONZE,
GUNMETAL, STAINLESS STEEL, COPPER OR MONEL.
6. THE ORDER IN WHICH THE PARTS/COMPONENTS ARE
MANUFACTURED AND THE MODEL IS ASSEMBLED IS ENTIRELY
LEFT TO THE BUILDER/MODELMAKER.
7. ERRORS AND/OR OMISSIONS MAY OCCUR IN THE DRAWING(S),
DO NOT HESITATE TO CONTACT ME SO THAT THE
STEAM OUT STEAM IN ERRORS/OMISSSIONS CAN BE RECTIFIED.
NOTES: DOWNLOADED SOME DRAWINGS AND ACCOMPANIED ARTICLE FROM INTERNET. MAGAZINE AND DESIGNER UNKNOWN
TITLE DRAWING CONTENTS PROJECT No 09E-17-00 MODEL SCALE: 1:1
JDWDS
PROJECTION

6 CYLINDER "ELBOW" STEAM ENGINE G.A. BOM, ISOMETRIC VIEWS, PARTS JDW DRAUGHTING SERVICES DATE
NOVEMBER-2015
DWG SCALE: 1:1 @A3 OR AS SHOWN
J.A.M. DE WAAL PAPAKURA NZ
Copyright ©

AND ASSEMBLIES
J.A.M. DE WAAL. 12 BRIGHTWELL STREET PAPAKURA 2110.
NEW ZEALAND. PHONE: OO64 09 2988815. MOB: 0211791000
E-MAIL: dewaal@xtra.co.nz. SHEET: 01 OF 01 A3 No: ELBOW-01