Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Electrical Installation Tester: Safety Information

Download as pdf or txt
Download as pdf or txt
You are on page 1of 5

1662/1663/1664 FC

Electrical Installation Tester


Safety Information

Go to www.fluke.com to register your Product and find more


information.
A Warning identifies conditions and procedures that are dangerous
to the user.
 Warnings
To prevent possible electrical shock, fire, or personal
injury:
• Use the Product only as specified, or the protection
supplied by the Product can be compromised.
• Carefully read all instructions.
• Read all safety information before you use the Product.
• Do not use the Product around explosive gas, vapor, or
in damp or wet environments.
• Comply with local and national safety codes. Use
personal protective equipment (approved rubber gloves,
face protection, and flame-resistant clothes) to prevent
shock and arc blast injury where hazardous live
conductors are exposed.
• Do not use the Product in distribution systems with
voltages >550 V.
• Use Product-approved measurement category (CAT),
voltage, and amperage rated accessories (probes, test
leads, and adapters) for all measurements.
• The battery door must be closed and locked before you
operate the Product.
• Examine the case before you use the Product. Look for
cracks or missing plastic. Carefully look at the insulation
around the terminals.
• Do not use test leads if they are damaged. Examine the
test leads for damaged insulation and measure a known
voltage.

PN 4477550 October 2015


©2015 Fluke Corporation. All rights reserved.
Specifications are subject to change without notification.
All product names are trademarks of their respective companies.
• Do not touch voltages >30 V ac rms, 42 V ac peak, or
60 V dc.
• Use the correct terminals, function, and range for
measurements.
• Do not apply more than the rated voltage between the
terminals or between each terminal and earth ground.
• Do not exceed the Measurement Category (CAT) rating of
the lowest rated individual component of a Product,
probe, or accessory.
• Keep fingers behind the finger guards on the probes.
• Measure a known voltage first to make sure that the
Product operates correctly.
• Replace the batteries when the low battery indicator
shows to prevent incorrect measurements.
• Remove all probes, test leads, and accessories before
the battery door is opened.
• Be sure that the battery polarity is correct to prevent
battery leakage.
• Repair the Product before use if the battery leaks.
• Have an approved technician repair the Product.
• Use only specified replacement parts.
• Replace a blown fuse with exact replacement only for
continued protection against arc flash.
• Do not operate the Product with covers removed or the
case open. Hazardous voltage exposure is possible.
• Disable the Product if it is damaged.
• Do not use the Product if it is damaged.
• Remove the input signals before you clean the Product.
• Use only current probes, test leads, and adapters
supplied with the Product.
• Remove test leads from the Product before the case is
opened.
• Do not use in CAT III or CAT IV environments without the
protective cap installed. The protective cap decreases
the possibility of arc flash caused by short circuits.
Symbols
Symbol Description

 WARNING. RISK OF DANGER.

WARNING. HAZARDOUS VOLTAGE. Risk of electric


 shock.

 Consult user documentation.

 Fuse

 Double Insulated

 Earth

 WARNING. Do not apply >550 Volts.

,/ - Battery Status

Measurement Category III is applicable to test and


 measuring circuits connected to the distribution part of
the building’s low-voltage MAINS installation.

Measurement Category IV is applicable to test and


 measuring circuits connected at the source of the
building’s low-voltage MAINS installation.

 Conforms to European Union directives.

Certified by CSA Group to North American safety


 standards.

 Conforms to relevant Australian EMC standards.

 Certified by TÜV SÜD Product Service.

This product complies with the WEEE Directive


marking requirements. The affixed label indicates that
you must not discard this electrical/electronic product in
domestic household waste. Product Category: With
 reference to the equipment types in the WEEE
Directive Annex I, this product is classed as category 9
"Monitoring and Control Instrumentation" product. Do
not dispose of this product as unsorted municipal
waste.
Safety Specifications
Fuses........................................ T3.15 A, 500 V, IR: 1500 A
Battery ...................................... 6 x AA Alkaline IEC LR6
Operating temperature ............. -10 °C to +40 °C
Storage temperature ................ -10 °C to +60 °C (limited by
battery specification)
-40 °C for 100 hrs
Relative Humidity ..................... 80 % 10 °C to 35 °C
70 % 35 °C to 40 °C
Altitude
Operating.............................. 2 000 m
Storage ................................. 12 000 m
Safety
IEC 61010 ............................ Pollution Degree 2
IEC 61010-2-030 .................. 300 V CAT IV, 500 V CAT III
Maximum voltage between any
terminal and earth ground .... 500 V
IEC 61010-031 (Accessories)
TP165X Remote
Probe with cap ................. CAT IV 600 V, CAT III 1000 V,
10 A
TP165X Remote Probe
without cap ....................... CAT II 1000 V, 10 A
TL-L1, TL-L2, TL-L3
Test Leads ....................... CAT IV 600 V, CAT III 1000 V,
10 A
Test Probes with cap........ CAT IV 600 V, CAT III 1000 V,
10 A
Test Probes without cap... CAT II 1000 V, 10 A
AC285 Alligator Clip ......... CAT IV 600 V, CAT III 1000 V,
10 A
Mains Test Cords ............. CAT II 250 V, 1000 V dc
Electromagnetic Compatibility (EMC)
International ......................... IEC 61326-1: Portable
CISPR 11: Group 1, Class A
Group 1: Equipment has intentionally generated and/or uses
conductively-coupled radio frequency energy that is
necessary for the internal function of the equipment itself.
Class A: Equipment is suitable for use in all establishments
other than domestic and those directly connected to a low-
voltage power supply network that supplies buildings used for
domestic purposes. There may be potential difficulties in
ensuring electromagnetic compatibility in other environments
due to conducted and radiated disturbances.
Wireless Radio with Adapter
Frequency Range................. 2402 MHz to 2480 MHz
Output Power ....................... <10 mW

LIMITED WARRANTY AND LIMITATION OF LIABILITY


This Fluke product will be free from defects in material and
workmanship for three years from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage from
accident, neglect, misuse, alteration, contamination, or abnormal
conditions of operation or handling. Resellers are not authorized to
extend any other warranty on Fluke’s behalf. To obtain service during
the warranty period, contact your nearest Fluke authorized service
center to obtain return authorization information, then send the
product to that Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY
CAUSE OR THEORY. Since some states or countries do not allow
the exclusion or limitation of an implied warranty or of incidental or
consequential damages, this limitation of liability may not apply to
you.
Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 P.O. Box 1186
Everett, WA 98206-9090 5602 BD Eindhoven
U.S.A. The Netherlands

11/99

You might also like