Wiper & Washer: Section
Wiper & Washer: Section
Wiper & Washer: Section
SECTION
WIPER & WASHER
WW B
E
CONTENTS
BASIC INSPECTION .................................... 3 Diagnosis Procedure ...............................................24 F
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 FRONT WIPER MOTOR LO CIRCUIT .............. 25
cardiagn.com
Work Flow ................................................................. 3 Component Function Check ....................................25
G
Diagnosis Procedure ...............................................25
FUNCTION DIAGNOSIS ............................... 6
FRONT WIPER MOTOR HI CIRCUIT ............... 27
FRONT WIPER AND WASHER SYSTEM .......... 6 Component Function Check ....................................27 H
System Diagram ........................................................ 6 Diagnosis Procedure ...............................................27
System Description ................................................... 6
Component Parts Location ........................................ 9 FRONT WIPER AUTO STOP SIGNAL CIR-
I
Component Description ............................................ 9 CUIT .................................................................. 29
Component Function Check ....................................29
REAR WIPER AND WASHER SYSTEM ...........11 Diagnosis Procedure ...............................................29
System Diagram ...................................................... 11 J
System Description ................................................. 11 FRONT WIPER MOTOR GROUND CIRCUIT ... 31
Component Parts Location ...................................... 13 Diagnosis Procedure ...............................................31
Component Description .......................................... 13 K
WASHER SWITCH ............................................ 32
HEADLAMP WASHER SYSTEM .......................15 Description ...............................................................32
System Diagram ...................................................... 15 Component Inspection .............................................32
System Description ................................................. 15 WW
Component Parts Location ...................................... 16
RAIN SENSOR .................................................. 33
Component Description .......................................... 16 Description ...............................................................33
Diagnosis Procedure ...............................................33
M
DIAGNOSIS SYSTEM (BCM) ............................17
REAR WIPER MOTOR CIRCUIT ...................... 34
COMMON ITEM ......................................................... 17 Component Function Check ....................................34
COMMON ITEM : CONSULT-III Function (BCM - Diagnosis Procedure ...............................................34 N
COMMON ITEM) ..................................................... 17
REAR WIPER AUTO STOP SIGNAL CIRCUIT
WIPER ....................................................................... 17 ... 36
WIPER : CONSULT-III Function (BCM - WIPER).... 17 O
Component Function Check ....................................36
Diagnosis Procedure ...............................................36
DIAGNOSIS SYSTEM (IPDM E/R) .....................19
Diagnosis Description ............................................. 19 HEADLAMP WASHER RELAY ........................ 38 P
CONSULT - III Function (IPDM E/R) ....................... 21 Component Inspection .............................................38
WW-1
Wiring Diagram - FRONT WIPER AND WASHER Exploded View ........................................................ 97
SYSTEM - ............................................................... 42 Hydraulic Layout ..................................................... 97
Removal and Installation ......................................... 97
REAR WIPER AND WASHER SYSTEM ........... 46 Inspection ................................................................ 98
Wiring Diagram - REAR WIPER AND WASHER
SYSTEM - ............................................................... 46 WASHER TANK ................................................ 99
Exploded View ........................................................ 99
HEADLAMP WASHER SYSTEM ...................... 51 Removal and Installation ......................................... 99
Wiring Diagram - HEADLAMP WASHER SYS-
TEM - ...................................................................... 51 WASHER PUMP ............................................... 100
Exploded View ...................................................... 100
ECU DIAGNOSIS ........................................ 54 Removal and Installation ....................................... 100
BCM (BODY CONTROL MODULE) .................. 54 HEADLAMP WASHER PUMP ......................... 101
Reference Value ..................................................... 54 Exploded View ...................................................... 101
Wiring Diagram - BCM - ......................................... 70 Removal and Installation ....................................... 101
Fail Safe ................................................................. 74
DTC Inspection Priority Chart .............................. 75 FRONT WASHER NOZZLE AND TUBE .......... 102
DTC Index .............................................................. 76 Hydraulic Layout ................................................... 102
Removal and Installation ....................................... 102
IPDM E/R (INTELLIGENT POWER DISTRI- Inspection and Adjustment .................................... 102
BUTION MODULE ENGINE ROOM) ................. 77
cardiagn.com
Reference Value ..................................................... 77 FRONT WIPER ARM ........................................ 104
Wiring Diagram - IPDM E/R - .................................. 83 Exploded View ...................................................... 104
Fail Safe ................................................................. 86 Removal and Installation ....................................... 104
DTC Index .............................................................. 88 Adjustment ............................................................ 105
WW-2
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001109306
B
OVERALL SEQUENCE
C
cardiagn.com
G
WW
P
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
WW-3
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
>> GO TO 2.
2.SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
cardiagn.com
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
WW-4
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
NO >> GO TO 3.
A
cardiagn.com
G
WW
WW-5
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
FRONT WIPER AND WASHER SYSTEM
System Diagram INFOID:0000000000896754
JPLIA0151GB
cardiagn.com
System Description INFOID:0000000000896755
OUTLINE
The front wiper is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Front wiper control function
Control by IPDM E/R
• Front wiper control function
• Relay control function
FRONT WIPER BASIC OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front wiper request signal to IPDM E/R with CAN communication depending on each
operating condition of the front wiper.
• IPDM E/R turns ON/OFF the integrated front wiper relay and the front wiper high relay according to the front
wiper request signal. IPDM E/R provides the power supply to operate the front wiper HI/LO operation.
FRONT WIPER LO OPERATION
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
front wiper LO operating condition.
Front wiper LO operating condition
- Ignition switch ON
- Front wiper switch LO or front wiper switch MIST (while pressing)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER HI OPERATION
• BCM transmits the front wiper request signal (HI) to IPDM E/R with CAN communication according to the
front wiper HI operating condition.
Front wiper HI operating condition
- Ignition switch ON
- Front wiper switch HI
• IPDM E/R turns ON the integrated front wiper relay and the front wiper high relay according to the front wiper
request signal (HI).
FRONT WIPER INT OPERATION (LINKED WITH VEHICLE SPEED)
WW-6
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM transmits the front wiper request signal (INT) to IPDM E/R with CAN communication according to the
front wiper INT operation condition and the intermittent operation delay interval judged value. A
Front wiper INT operating condition
- Ignition switch ON
- Front wiper switch INT B
cardiagn.com
4 16 12 8 4.8
G
5 24 18 12 7.2
6 32 24 16 9.6
↓ H
7 42 31.5 21 12.6
Long
• IPDM E/R turns the integrated front wiper relay ON so that the front wiper is operated only once according to
the front wiper request signal (INT). I
• BCM detects stop position/except stop position of the front wiper motor according to the front wiper stop
position signal received from IPDM E/R with CAN communication.
• BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval after J
the front wiper motor is stopped.
WW
M
JPLIA0094GB
WW-7
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
cardiagn.com
• When the front wiper request signal is stopped, IPDM E/R turns ON the front wiper relay until the front wiper
motor returns to the stop position.
JPLIA0095GB
NOTE:
• BCM stops the transmitting of the front wiper request signal when the ignition switch is OFF.
• IPDM E/R turns the front wiper relay OFF when the ignition switch is OFF.
FRONT WIPER OPERATION LINKED WITH WASHER
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication according to the
washer linked operating condition of the front wiper.
• BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 3 times
when the front washer switch OFF is detected.
Washer linked operating condition of front wiper
- Ignition switch ON
- Front washer switch ON (0.4 second or more)
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
• The washer pump is grounded through the combination switch with the front washer switch ON.
FRONT WIPER DROP WIPE OPERATION
• BCM controls the front wiper to operate once according to the conditions of front wiper drop wipe operation.
Front wiper drop wipe operating condition
- Ignition switch ON
- Front wiper switch OFF
- Front washer switch OFF
WW-8
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• BCM transmits the front wiper request signal (LO) to IPDM E/R with CAN communication so that the front
wiper operate once three seconds after front wiper operation linked with washer. A
• IPDM E/R turns ON the integrated front wiper relay according to the front wiper request signal (LO).
FRONT WIPER FAIL−SAFE OPERATION
• IPDM E/R performs the fail-safe function when the front wiper auto stop circuit is malfunctioning. Refer to B
PCS-28, "Fail Safe".
• BCM performs fail-safe operation when light and rain sensor or light and rain sensor-related systems are
malfunctioning. Refer to BCS-59, "Fail Safe". C
Component Parts Location INFOID:0000000000896757
cardiagn.com
G
WW
JPLIA0185ZZ
P
1. Combination switch 2. Combination meter 3. Light and rain sensor
4. BCM 5. Washer pump 6. IPDM E/R
7. Front wiper motor
A. Inside mirror cover inside B. Over the glove box C. Radiator core support (RH)
D. Engine room (left side) E. Cowl top, left side of engine room F. Cowl top, right side of engine room
WW-9
FRONT WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Requests (with CAN communication) the front wiper relay and the front wiper high relay ON to
IPDM E/R.
• Controls the integrated relay according to the request (with CAN communication) from BCM.
IPDM E/R
• Performs the auto stop control of the front wiper.
Combination switch
Refer to BCS-9, "System Diagram".
(Wiper & washer switch)
Combination meter Transmits the vehicle speed signal to BCM with CAN communication.
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal
Light and rain sensor
to BCM through the light and rain sensor serial link.
cardiagn.com
WW-10
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
A
System Diagram INFOID:0000000000896810
JPLIA0162GB
F
System Description
cardiagn.com
INFOID:0000000000896811
G
OUTLINE
The rear wiper is controlled by each function of BCM and IPDM E/R.
H
Control by BCM
• Combination switch reading function
• Rear wiper control function
I
Control by IPDM E/R
• Reverse-linked rear wiper function
REAR WIPER BASIC OPERATION J
• BCM detects the combination switch condition by the combination switch reading function.
• BCM controls the rear wiper to start or stop.
REAR WIPER ON OPERATION K
• BCM supplies power to the rear wiper motor according to the rear wiper ON operating condition.
Rear wiper ON operating condition
- Ignition switch ON WW
- Rear wiper switch ON
REAR WIPER INT OPERATION LINKED WITH VEHICLE SPEED
M
• BCM supplies power to the rear wiper motor according to the INT operating condition.
Rear wiper INT operating condition
- Ignition switch ON N
- Rear wiper switch INT
• BCM controls the rear wiper to operate once.
• BCM detects the rear wiper motor stopping position.
• BCM supplies power to the rear wiper motor after an intermittent from the stop of the rear wiper motor. O
JPLIA0165GB
WW-11
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
REAR WIPER AUTO STOP OPERATION
• BCM stops supplying power to the rear wiper motor when the rear wiper switch is turned OFF.
• BCM reads an auto stop signal from the rear wiper motor to detect a rear wiper motor position.
• When the rear wiper motor is at other than the stopping position, BCM continues to supply power to the rear
wiper motor until it returns to the stopping position.
JPLIA0166GB
cardiagn.com
NOTE:
BCM stops supplying power to the rear wiper motor when the ignition switch is turned OFF.
REAR WIPER OPERATION LINKED WITH WASHER
• BCM supplies power to the rear wiper motor according to the washer linked operating condition of rear
wiper. When the rear washer switch is turned OFF, BCM controls rear wiper to operate approximately three
times.
Washer linked operating condition of rear wiper
- Ignition switch ON
- Rear washer switch ON (0.4 second or more)
• Washer pump becomes grounded through the combination switch when the rear washer switch is turned
ON.
REAR WIPER OPERATION LINKED WITH REVERSE
• BCM controls rear wiper to operate once according to the conditions of rear wiper operation linked with
reverse.
Condition of rear wiper operation linked with reverse
- Ignition switch ON
- Front wiper switch: LO, HI, AUTO*1, or INT*2
NOTE:
*1: With light and rain sensor
*2: Without light and rain sensor
- Rear wiper switch OFF
- Selector lever “R”.
• IPDM E/R transmits a reverse switch signal to BCM through the CAN communication line when the selector
lever is shifted to the “R”.
• BCM supplies power to the rear wiper motor when receiving the reverse switch signal.
REAR WIPER DROP WIPE OPERATION
• BCM controls the rear wiper to operate once according to the rear wiper drop wipe operating condition.
Rear wiper drop wipe operating condition
- Ignition switch ON
- Rear wiper switch OFF
- Rear washer switch OFF
• BCM controls the rear wiper so that it operates once time approximately three seconds later after the washer
interlocking operation of the rear wiper.
REAR WIPER FAIL−SAFE OPERATION
WW-12
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
BCM performs the fail-safe function when the rear wiper auto stop circuit is malfunctioning. Refer to BCS-59,
"Fail Safe". A
Component Parts Location INFOID:0000000000896812
cardiagn.com
G
WW
JPLIA0186ZZ
N
1. Combination switch 2. Combination meter 3. BCM
4. Washer pump 5. IPDM E/R 6. Rear wiper motor
A. Over the glove box B. Radiator core support (RH) C. Engine room (left side) O
D. Back door trim finisher lower inside
Part Description
• Judges each switch status by the combination switch reading function.
BCM • Supplies power to the rear wiper motor.
• Performs the auto stop control of the rear wiper.
WW-13
REAR WIPER AND WASHER SYSTEM
< FUNCTION DIAGNOSIS >
Part Description
IPDM E/R Transmits the reverse switch signal to BCM with CAN communication.
Combination switch
Refer to BCS-9, "System Diagram".
(Wiper & washer switch)
cardiagn.com
WW-14
HEADLAMP WASHER SYSTEM
< FUNCTION DIAGNOSIS >
HEADLAMP WASHER SYSTEM
A
System Diagram INFOID:0000000000896814
JPLIA0152GB
F
System Description
cardiagn.com
INFOID:0000000000896815
G
OUTLINE
The headlamp washer is controlled by each function of BCM and IPDM E/R.
H
Control by BCM
• Combination switch reading function
• Headlamp washer control function
I
Control by IPDM E/R
• Relay control function
HEADLAMP WASHER BASIC OPERATION J
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the headlamp washer request signal to IPDM E/R with CAN communication depending on
each operating condition of the headlamp washer.
K
WW
O
JPLIA0177GB
WW-15
HEADLAMP WASHER SYSTEM
< FUNCTION DIAGNOSIS >
• IPDM E/R turns ON/OFF the headlamp washer relay by receiving the headlamp washer request signal, and
controls the headlamp washer twice.
Component Parts Location INFOID:0000000000896816
cardiagn.com
JPLIA0187ZZ
Part Description
• Judges each switch status by the combination switch reading function.
BCM
• Requests (with CAN communication) the headlamp washer relay ON to IPDM E/R.
Controls the integrated relay according to the request (with CAN communication) from
IPDM E/R
BCM.
Combination switch
Refer to BCS-9, "System Diagram".
(Wiper & washer switch)
WW-16
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001054857
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
WORK SUPPORT Changes the setting for each system function.
D
SELF-DIAG RESULTS Displays the diagnosis results judged by BCM. Refer to BCS-61, "DTC Index".
CAN DIAG SUPPORT MNTR Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR The BCM input/output signals are displayed. E
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION The BCM part number is displayed.
• Enables to read and save the vehicle specification. F
CONFIGURATION
• Enables to write the vehicle specification when replacing BCM.
cardiagn.com
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
H
Diagnosis mode
System Sub system selection item
WORK SUPPORT DATA MONITOR ACTIVE TEST
I
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
K
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × × WW
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY × M
Combination switch COMB SW ×
Immobilizer IMMU × ×
N
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk open TRUNK ×
Vehicle security system THEFT ALM × × × O
Signal buffer system SIGNAL BUFFER × ×
PTC heater system PTC HEATER × ×
P
WIPER
WIPER : CONSULT-III Function (BCM - WIPER) INFOID:0000000000896761
WORK SUPPORT
WW-17
DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
Setting
Service item Description
item
With vehicle speed
ON*
WIPER SPEED (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
SETTING Without vehicle speed
OFF
(Front wiper intermittent time linked with the wiper intermittent dial position)
*:Factory setting
DATA MONITOR
Monitor Item
Description
[Unit]
IGN ON SW Ignition switch ON status judged from ignition power supply.
IGN SW CAN Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[OFF/ON]
FR WIPER LOW
[OFF/ON]
Each switch status that BCM judges from the combination switch reading function.
cardiagn.com
FR WIPER INT
[OFF/ON]
FR WASHER SW
[OFF/ON]
H/L WASH SW NOTE:
[OFF/ON] The item is indicated, but not monitored.
INT VOLUME
Each switch status that BCM judges from the combination switch reading function.
[1 − 7]
FR WIPER STOP Front wiper motor (stop position) status received from IPDM E/R with CAN communica-
[OFF/ON] tion.
VEHICLE SPEED The value of the vehicle speed signal received from combination meter with CAN com-
[km/h] munication.
RR WIPER ON
[OFF/ON]
RR WIPER INT
Each switch status that BCM judges from the combination switch reading function.
[OFF/ON]
RR WASHER SW
[OFF/ON]
RR WIPER STOP
Rear wiper motor (stop position) status input from the rear wiper motor.
[OFF/ON]
ACTIVE TEST
WW-18
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (IPDM E/R)
A
Diagnosis Description INFOID:0000000001054858
cardiagn.com
operation)
NOTE: G
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the H
ignition switch OFF.
CAUTION:
Close passenger door. I
4. Turn the ignition switch ON within 10 seconds. Then the horn sounds once and the auto active test starts.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed. J
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION: K
• If auto active test mode cannot be actuated, check door switch system.
• Never start the engine.
Inspection in auto active test mode WW
When auto active test mode is actuated, the following 6 steps are repeated 3 times.
JPMIA0234ZZ
WW-19
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Operation
Inspection location Operation
sequence
1 Oil pressure warning lamp Blinks continuously during operation of auto active test.
2 Rear window defogger 10 seconds
3 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps
4 10 seconds
• Tail lamps
• Front fog lamps
5 Headlamps LO ⇔ HI 5 times
6 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
7 Cooling fan LO for 5 seconds → HI for 5 seconds
cardiagn.com
JPMIA0235GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
WW-20
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Symptom Inspection contents Possible cause
A
• Communication signal between BCM
and auto amp. (with auto A/C)
• Communication signal between BCM
and heater control panel (without auto B
A/C, with manual A/C)
YES
• BCM
Perform auto active test. • CAN communication signal between
A/C compressor does not operate Does the magnet clutch oper- BCM and ECM C
ate? • CAN communication signal between
ECM and IPDM E/R
• Magnet clutch D
• Harness or connector between IPDM
NO
E/R and magnet clutch
• IPDM E/R
• Harness or connector between IPDM E
E/R and oil pressure switch
YES
• Oil pressure switch
Perform auto active test. • IPDM E/R
F
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal between
lamp blink? IPDM E/R and BCM
cardiagn.com
NO • CAN communication signal between
BCM and combination meter G
• Combination meter
• ECM signal input circuit
YES • CAN communication signal between H
ECM and IPDM E/R
• Cooling fan
• Cooling fan ground circuit
I
Perform auto active test. • Harness or connector between IPDM
Cooling fan does not operate E/R and cooling fan
Does the cooling fan operate?
• IPDM E/R
NO
• Cooling fan relay-3* J
• Harness or connector between IPDM
E/R and cooling fan relay-3*
• Harness or connector between cooling
fan and cooling fan relay-3* K
NOTE:
*: MR engine and K9K engine models
WW
M
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
N
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R. O
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
P
SELF DIAGNOSTIC
Refer to PCS-30, "DTC Index".
DATA MONITOR
Monitor item
WW-21
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
cardiagn.com
WIP AUTO STOP
× Displays the status of the front wiper auto stop signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
ST RLY REQ Displays the status of the ignition and starter request signal received from BCM via CAN
[Off/On] communication.
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R.
[Off/On]
RR DEF REQ Displays the status of the rear defogger request signal received from BCM via CAN com-
×
[Off/On] munication.
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
REV SW
Displays the status of the reverse switch judged by IPDM E/R.
[Off/On]
Displays the status of the hood switch judged by IPDM E/R.
HOOD SW
NOTE:
[Off/On]
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system.
Displays the status of the theft warning horn request signal received from BCM via CAN
THFT HRN REQ communication.
[Off/On] NOTE:
This item is monitored only the vehicle with the Vehicle Security (Theft Warning) system.
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored.
IGN ON SW
Displays the status of the ignition switch judged by IPDM E/R.
[Off/On]
ACTIVE TEST
Test item
WW-22
DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Test item Operation Description
A
1 OFF
2 Operates the cooling fan relay (low operation).
MOTOR FAN
3 B
Operates the cooling fan relay (high operation).
4
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF C
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS D
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 sec-
Hi
ond intervals.
Fog Operates the front fog lamp relay. E
HORN On Operates horn relay for 20 ms.
cardiagn.com
G
WW
WW-23
WIPER AND WASHER FUSE, FUSIBLE LINK
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
WIPER AND WASHER FUSE, FUSIBLE LINK
Description INFOID:0000000000896764
cardiagn.com
Front wiper
IPDM E/R #44 30 A
motor
Washer pump Fuse block #3 20 A
Headlamp Fuse and fusible
#G 30 A
washer pump link block
Is the fuse or fusible link fusing?
YES >> Replace the fuse block or fusible link with a new one after repairing the applicable circuit.
NO >> The fuse or fusible link is normal.
WW-24
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR LO CIRCUIT
A
Component Function Check INFOID:0000000000924447
cardiagn.com
Diagnosis Procedure INFOID:0000000000924448
G
1.CHECK FRONT WIPER MOTOR FUSE
1. Turn the ignition switch OFF. H
2. Check that the following fuses are not fusing.
IPDM E/R
Continuity
Connector Terminal Ground M
E10 7 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors. And then replace the fuse. N
NO >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
3.CHECK FRONT WIPER MOTOR (LO) OUTPUT VOLTAGE O
CONSULT-III ACTIVE TEST
1. Connect IPDM E/R connector.
2. Turn the ignition switch ON.
P
3. Select "FRONT WIPER" of IPDM E/R active test item.
4. With operating the test item, check voltage between IPDM E/R harness connector and ground.
WW-25
FRONT WIPER MOTOR LO CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIP-
Connector Terminal ER
Ground Battery
LO
E10 7 voltage
OFF 0V
Is the measurement value normal?
YES >> GO TO 4.
NO >> Replace IPDM E/R.
4.CHECK FRONT WIPER MOTOR (LO) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
cardiagn.com
Connector Terminal Connector Terminal
E10 7 E20 2 Existed
Does continuity exist?
YES >> Replace front wiper motor.
NO >> Repair the harnesses or connectors.
WW-26
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR HI CIRCUIT
A
Component Function Check INFOID:0000000000924449
cardiagn.com
1.CHECK FRONT WIPER MOTOR FUSE G
WW-27
FRONT WIPER MOTOR HI CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals
Test item
(+) (-) Voltage
IPDM E/R (Approx.)
FRONT WIP-
Connector Terminal ER
Ground Battery
HI
E10 8 voltage
OFF 0V
Is the measurement value normal?
YES >> GO TO 4.
NO >> Replace IPDM E/R.
4.CHECK FRONT WIPER MOTOR (HI) OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.
cardiagn.com
Connector Terminal Connector Terminal
E10 8 E20 1 Existed
Does continuity exist?
YES >> Replace front wiper motor.
NO >> Repair the harnesses or connectors.
WW-28
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
A
Component Function Check INFOID:0000000000924451
Monitor D
Monitor item Condition
status
Stop position STOP P
Front wiper mo-
FR WIPER STOP Except stop posi- E
tor ACT P
tion
Is the status of item normal?
YES >> Front wiper auto stop signal circuit is normal. F
NO >> Refer to WW-29, "Diagnosis Procedure".
cardiagn.com
Diagnosis Procedure INFOID:0000000000924452
G
Terminals
(+) (-) Voltage J
IPDM E/R (Approx.)
WW-29
FRONT WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
cardiagn.com
WW-30
FRONT WIPER MOTOR GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
A
Diagnosis Procedure INFOID:0000000000924453
cardiagn.com
G
WW
WW-31
WASHER SWITCH
< COMPONENT DIAGNOSIS >
WASHER SWITCH
Description INFOID:0000000000896851
JPLIA0163GB
cardiagn.com
1. Turn the ignition switch OFF.
2. Disconnect combination switch connector.
3. Check continuity between the combination switch terminals.
A : Terminal 14
B : Terminal 12
C : Terminal 13
D : Terminal 11
JPLIA0164GB
Combination switch
Condition Continuity
Terminal
11 12
Front washer switch ON
13 14
Existed
11 14
Rear washer switch ON
12 13
Does continuity exist?
YES >> Wiper and washer switch is normal.
NO >> Replace wiper and washer switch.
WW-32
RAIN SENSOR
< COMPONENT DIAGNOSIS >
RAIN SENSOR
A
Description INFOID:0000000000984465
Detects water droplets on the windshield with infrared rays, and transmits the rain sensor signal to BCM B
through the light and rain sensor serial link.
Diagnosis Procedure INFOID:0000000000907640
C
Refer to EXL-69, "Component Function Check".
cardiagn.com
G
WW
WW-33
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER MOTOR CIRCUIT
Component Function Check INFOID:0000000000903198
cardiagn.com
1. Turn the ignition switch OFF.
2. Disconnect rear wiper motor connector.
3. Turn the ignition switch ON.
4. Select "RR WIPER" of BCM active test item.
5. With operating the test item, check voltage between BCM harness connector and ground.
Terminals
Test item
(+) (−) Voltage
BCM (Approx.)
REAR WIPER
Connector Terminal
Ground Battery
ON
M66 43 voltage
OFF 0V
Is the measurement value normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK REAR WIPER MOTOR GROUND OPEN CIRCUIT
1. Turn the ignition switch OFF.
2. Check continuity between rear wiper motor harness connector and ground.
WW-34
REAR WIPER MOTOR CIRCUIT
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
WW-35
REAR WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
REAR WIPER AUTO STOP SIGNAL CIRCUIT
Component Function Check INFOID:0000000000903201
Monitor
Monitor item Condition
status
Stop position ON
RR WIPER STOP Rear wiper motor Except stop posi-
OFF
tion
Is the status of item normal?
YES >> Rear wiper auto stop signal circuit is normal.
NO >> Refer to WW-36, "Diagnosis Procedure".
cardiagn.com
Diagnosis Procedure INFOID:0000000000903200
Terminals
(+) (−) Voltage
BCM (Approx.)
BCM
Continuity
Connector Terminal Ground
M66 44 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> Replace BCM. Refer to BCS-64, "Exploded View".
3.CHECK REAR WIPER MOTOR (AUTO STOP) CIRCUIT CONTINUITY
1. Check continuity between BCM harness connector and rear wiper motor harness connector.
WW-36
REAR WIPER AUTO STOP SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
WW-37
HEADLAMP WASHER RELAY
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER RELAY
Component Inspection INFOID:0000000000903229
cardiagn.com
WW-38
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER CIRCUIT
A
Component Function Check INFOID:0000000000904047
cardiagn.com
G
1. Turn the ignition switch OFF.
2. Check that the headlamp washer 30A fusible link (#G) is not fusing.
Is the fusible link fusing? H
YES >> Replace the fusible link after repairing the applicable circuit.
NO >> GO TO 2.
2.CHECK HEADLAMP WASHER RELAY POWER SUPPLY I
1. Remove headlamp washer relay.
2. Turn the ignition switch ON.
3. Check voltage between headlamp washer harness connector and ground. J
Terminals
K
(+) (−) Voltage (Ap-
Headlamp washer relay prox.)
Connector Terminal WW
Ground
2
E32 Battery voltage
3
M
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair the harnesses or connectors.
N
3.CHECK HEADLAMP WASHER RELAY
1. Check headlamp washer relay. Refer to WW-38, "Component Inspection".
Is the headlamp washer relay normal? O
YES >> GO TO 4.
NO >> Replace the headlamp washer relay.
4.CHECK HEADLAMP WASHER RELAY SIGNAL OUTPUT P
WW-39
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
Terminals
Test item
(+) (−)
Voltage (Ap-
IPDM E/R HEAD- prox.)
LAMP
Connector Terminal WASHER
Ground
ON 0V
E13 39 Battery volt-
OFF
age
Is the measurement value normal?
YES >> GO TO 7.
Fixed at 0 V >> GO TO 5.
Fixed at Battery voltage >> Replace IPDM E/R.
5.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL OPEN CIRCUIT
1. Remove headlamp washer relay.
2. Disconnect IPDM E/R harness connector.
3. Check continuity between IPDM E/R harness connector and headlamp washer relay harness connector.
cardiagn.com
IPDM E/R Headlamp washer relay
Continuity
Connector Terminal Connector Terminal
E13 39 E32 4 Existed
Does continuity exist?
YES >> GO TO 6.
NO >> Repair the harnesses or connectors.
6.CHECK HEADLAMP WASHER RELAY CONTROL SIGNAL SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
IPDM E/R
Continuity
Connector Terminal Ground
E13 39 Not existed
Does continuity exist?
YES >> Repair the harnesses or connectors.
NO >> Replace IPDM E/R.
7.CHECK HEADLAMP WASHER PUMP OPEN CIRCUIT
1. Disconnect headlamp washer pump connector.
2. Remove headlamp washer relay.
3. Check continuity between headlamp washer relay harness connector and headlamp washer pump har-
ness connector.
WW-40
HEADLAMP WASHER CIRCUIT
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
WW-41
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
FRONT WIPER AND WASHER SYSTEM
Wiring Diagram - FRONT WIPER AND WASHER SYSTEM - INFOID:0000000000924454
cardiagn.com
JCLWA0392GB
WW-42
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
JCLWA0393GB
WW-43
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
JCLWA0394GB
WW-44
FRONT WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
JCLWA0395GB
WW-45
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
REAR WIPER AND WASHER SYSTEM
Wiring Diagram - REAR WIPER AND WASHER SYSTEM - INFOID:0000000000978701
cardiagn.com
JCLWA0396GB
WW-46
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
JCLWA0397GB
WW-47
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
JCLWA0398GB
WW-48
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
JCLWA0399GB
WW-49
REAR WIPER AND WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
JCLWA0400GB
WW-50
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
HEADLAMP WASHER SYSTEM
A
Wiring Diagram - HEADLAMP WASHER SYSTEM - INFOID:0000000000978703
cardiagn.com
G
WW
P
JCLWA0401GB
WW-51
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
JCLWA0402GB
WW-52
HEADLAMP WASHER SYSTEM
< COMPONENT DIAGNOSIS >
cardiagn.com
G
WW
JCLWA0403GB
WW-53
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001116753
cardiagn.com
Back door closed OFF
BACK DOOR SW
Back door opened ON
BATTERY VOLT
NOTE: Approximately the same as power
Ignition switch ON
Diesel engine models supply voltage
only
Driver's seat belt unfastened OFF
BUCKLE SW
Driver's seat belt fastened ON
Door lock/unlock switch does not operate OFF
CDL LOCK SW
Press door lock/unlock switch to the LOCK side ON
Door lock/unlock switch does not operate OFF
CDL UNLOCK SW
Press door lock/unlock switch to the UNLOCK side ON
Passenger door closed OFF
DOOR SW-AS
Passenger door opened ON
Driver door closed OFF
DOOR SW-DR
Driver door opened ON
Rear LH door closed OFF
DOOR SW-RL
Rear LH door opened ON
Rear RH door closed OFF
DOOR SW-RR
Rear RH door opened ON
Fan switch ON (when engine coolant is
cool)
NOTE: OFF
Depending on the ambient tempera-
ture, battery voltage, etc.
ELEC PWR CUT The current status maintained with the
FREEZ
NOTE: signal from ECM received.
Engine running
Diesel engine models
• Fan switch OFF
only
• Fan switch ON after engine warming
UP
NOTE: INHBT
Depending on the engine coolant
temperature, ambient temperature,
battery voltage, etc.
WW-54
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
ENG COOLNT T
NOTE: Approximately the same as water
Engine running
Diesel engine models temperature gauge reading
only B
ENGINE RPM
NOTE: Approximately the same as tachom-
Engine running
Diesel engine models eter reading
only
C
Engine stopped OFF
ENGINE RUN
Engine running ON D
Engine stopped STOP
ENGINE STATUS
NOTE: While the engine stalls STALL
Diesel engine models Engine running RUN E
only
At engine cranking CRA
Fan switch OFF OFF
FAN ON SIG F
Fan switch ON ON
Front fog lamp switch OFF OFF
cardiagn.com
FR FOG SW
Front fog lamp switch ON ON G
Front washer switch OFF OFF
FR WASHER SW
Front washer switch ON ON
H
Front wiper switch OFF OFF
FR WIPER LOW
Front wiper switch LO ON
Front wiper switch OFF OFF I
FR WIPER HI
Front wiper switch HI ON
Front wiper switch OFF OFF
FR WIPER INT J
Front wiper switch INT ON
Any position other than front wiper stop position OFF
FR WIPER STOP
Front wiper stop position ON K
When hazard switch is not pressed OFF
HAZARD SW
When hazard switch is pressed ON
Lighting switch OFF OFF WW
HEAD LAMP SW 1
Lighting switch 2ND ON
Lighting switch OFF OFF
HEAD LAMP SW 2 M
Lighting switch 2ND ON
Lighting switch OFF OFF
HI BEAM SW
Lighting switch HI ON N
Close the hood
NOTE: OFF
HOOD SW Vehicles without theft warning system are OFF-fixed O
Open the hood ON
NOTE:
H/L WASH SW OFF
The item is indicated, but not monitored P
Ignition switch OFF or ACC OFF
IGN ON SW
Ignition switch ON ON
Ignition switch OFF or ACC OFF
IGN SW CAN
Ignition switch ON ON
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7
WW-55
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
LOCK button of Intelligent Key is not pressed OFF
I-KEY LOCK
LOCK button of Intelligent Key is pressed ON
UNLOCK button of Intelligent Key is not pressed OFF
I-KEY UNLOCK
UNLOCK button of Intelligent Key is pressed ON
Mechanical key is removed from key cylinder OFF
KEY ON SW
Mechanical key is inserted to key cylinder ON
LOCK button of key fob is not pressed OFF
KEYLESS LOCK
LOCK button of key fob is pressed ON
UNLOCK button of key fob is not pressed OFF
KEYLESS UNLOCK
UNLOCK button of key fob is pressed ON
Light & rain sensor is in normal condition OK
LIT-SEN FAIL
Light & rain sensor is with internal error NOTOK
• Ignition switch OFF or ACC
OFF
OIL PRESS SW • Engine running
Ignition switch ON ON
cardiagn.com
OUT SIDE TEMP
Approximately the same as outside
NOTE: Ignition switch ON
air temperature
Diesel engine models
Other than lighting switch PASS OFF
PASSING SW
Lighting switch PASS ON
Return to ignition switch to LOCK position OFF
PUSH SW
Press ignition switch ON
Rear window defogger switch OFF OFF
REAR DEF SW
Rear window defogger switch ON ON
WW-56
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
Turn signal switch OFF OFF
TURN SIGNAL L
Turn signal switch LH ON
Turn signal switch OFF OFF B
TURN SIGNAL R
Turn signal switch RH ON
NOTE: OFF
UNLOCK WITH DR
The item is indicated, but not monitored ON C
Other than the following OFF
UNLOCK SHOCK
During the unlock operation interlocked with air bag ON
D
VEHICLE SPEED While driving Equivalent to speedometer reading
cardiagn.com
G
WW
WW-57
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
JPMIA0145GB
cardiagn.com
PHYSICAL VALUES
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT -III. Refer to
BCS-26, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-7, "System
Description".
WW-58
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
Combination
2 Combination switch switch Front fog lamp switch ON G
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH H
JPMIA0163GB
9.3 V
All switch OFF 0V I
Lighting switch AUTO
Rear fog lamp switch OFF
Combination J
3 Combination switch switch Front wiper switch MIST
Ground Output
(LG) OUTPUT 3 (Wiper intermit- Front wiper switch INT
tent dial 4)
K
Front wiper switch LO JPMIA0162GB
9.3 V
All switch OFF WW
0V
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4) M
Rear wiper switch ON
(Wiper intermittent dial 4)
4 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Rear washer switch ON N
(Wiper intermittent dial 4)
Any of the condition below
with all switch OFF
JPMIA0161GB O
• Wiper intermittent dial 1
9.1 V
• Wiper intermittent dial 5
• Wiper intermittent dial 6
P
WW-59
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF 0V
Lighting switch 1ST
Lighting switch 2ND
Combination
5 Combination switch switch Lighting switch HI
Ground Output
(W) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0164GB
9.1 V
cardiagn.com
JPMIA0154GB
1.2 V
Pressed to the lock side 0V
8 Not pressed
Ground Hazard switch Output Hazard switch
(LG)
JPMIA0154GB
1.3 V
Pressed 0V
JPMIA0154GB
1.2 V
Pressed to the unlock side 0 V
JPMIA0154GB
1.2 V
Pressed 0V
WW-60
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Ignition switch OFF or ACC 0V
B
13
Ground Shock detect sensor Input
C
(R) Ignition switch ON
D
JPMIA0155GB
6.0 V
cardiagn.com
Ignition switch OFF or ACC Battery voltage G
H
17 Light & rain sensor
Ground Output
(BR) serial link Ignition switch ON
I
JPMIA0156GB
8.7 V
ON 0V J
K
18 Security indica-
Ground Security indicator Output Blinking
(SB) tor
WW
JPMIA0014GB
10.3 V
M
OFF Battery voltage
19 Input/
— CAN-H — —
(L) Output
N
20 Input/
— CAN-L — —
(P) Output
JPMIA0154GB
1.1 V
While pressing 0V
WW-61
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
11.2 V
ON (When rear door LH
0V
opened)
cardiagn.com
OFF (When driver door
26 Driver door closed)
Ground Driver door switch Input
(R) switch
PKID0924E
11.2 V
ON (When driver door
0V
opened)
11.2 V
ON (When passenger
0V
door opened)
OFF (When back door
Battery voltage
28 Back door closed)
Ground Back door switch Input
(G) switch ON (When back door
0V
opened)
11.2 V
ON (When rear door RH
0V
opened)
30
Ground Audio link Output — — —
(SB)
WW-62
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.3 V D
E
Front fog lamp switch ON
(Wiper intermittent dial 4)
F
JPMIA0167GB
1.3 V
cardiagn.com
G
JPMIA0168GB
I
1.3 V
JPMIA0169GB
1.3 V WW
1.3 V
O
WW-63
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V
JPMIA0167GB
1.3 V
cardiagn.com
Combination
32 Combination switch switch
Ground Input Lighting switch 2ND
(G) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0166GB
1.3 V
JPMIA0168GB
1.3 V
JPMIA0196GB
1.3 V
WW-64
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
F
JPMIA0167GB
1.3 V
cardiagn.com
G
Combination
33 Combination switch switch
H
Ground Input Turn signal switch RH
(V) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0166GB
I
1.3 V
JPMIA0168GB
1.3 V WW
N
JPMIA0196GB
1.3 V
O
WW-65
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V
JPMIA0167GB
1.3 V
cardiagn.com
34 Combination switch Combination Lighting switch 1ST
Ground Input
(GR) INPUT 4 switch (Wiper intermittent dial 4)
JPMIA0166GB
1.3 V
JPMIA0167GB
1.3 V
JPMIA0196GB
1.3 V
WW-66
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
JPMIA0165GB
1.4 V D
E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0166GB
1.3 V
cardiagn.com
G
JPMIA0167GB
I
1.3 V
JPMIA0169GB
1.3 V WW
1.3 V
Insert mechanical key into ignition key cylin- O
Battery voltage
36 der
Ground Key switch Output
(V) Remove mechanical key from ignition key
0V
cylinder P
37 Ignition switch OFF 0V
Ground ACC power supply Output
(R) Ignition switch ACC or ON Battery voltage
WW-67
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Just after Insert mechanical key
39 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(P) Output der
of tester should move
Just after Insert mechanical key
40 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(LG) Output der
of tester should move
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage
(V) ply
After passing the interior room lamp battery
0V
42 Interior room lamp saver operation time
Ground Output
(V) power supply Any other time after passing the interior room
Battery voltage
lamp battery saver operation time
cardiagn.com
44 Ignition switch
Ground Rear wiper auto stop Output Any position other than
(L/W) ON
rear wiper stop position
JPMIA0197GB
45 Back door lock actu- Back door Pressed Battery voltage (300ms)
Ground Output
(GR) ator opener switch Not pressed 0V
Turn signal switch OFF 0V
47 Ignition switch
Ground Turn signal LH Output
(G/Y) ON Turn signal switch LH
PKID0926E
6.5 V
Turn signal switch OFF 0V
48 Ignition switch
Ground Turn signal RH Output
(G/B) ON Turn signal switch RH
PKID0926E
6.5 V
Lighting switch Rear fog lamp switch OFF 0 V
49 1ST and front
Ground Rear fog lamp Output
(Y) fog lamp switch Rear fog lamp switch ON Battery voltage
ON
51 Depress the brake pedal Battery voltage
(R/W)*1 Ground Stop lamp switch Output
(R)*2 Release the brake pedal 0V
WW-68
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
cardiagn.com
(P) er supply
When lock button of key fob or Intelligent Key
G
0V
59 is not pressed
Ground Super lock Output
(BR) When lock button of key fob or Intelligent Key
Battery voltage H
is pressed
WW
WW-69
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - BCM - INFOID:0000000001116754
cardiagn.com
TKWT3486E
WW-70
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
G
WW
TKWT3487E
WW-71
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
JCMWA0409GB
WW-72
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
G
WW
JCMWA0410GB
WW-73
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
JCMWA0411GB
Fail-safe index
BCM performs fail-safe control when any DTC listed below is detected.
WW-74
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
cardiagn.com
REAR WIPER CONTROL
BCM detects a rear wiper stopping position according to a rear wiper auto stop signal. G
When a rear wiper auto stop signal is in the condition listed below, BCM stops power supply to rear wiper after
rear wiper is activated for five seconds.
H
Ignition switch Rear wiper switch Auto stop signal
Rear wiper stop position signal cannot be
OFF
ON input 5 seconds. I
ON The signal does not change for 5 seconds.
NOTE:
The above operation is repeated when operating the rear wiper switch one minute after the stop of the rear J
wiper caused by Fail-safe.
TURN SIGNAL LAMP CONTROL
K
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE: WW
The blinking speed is normal while activating the hazard warning lamp.
LIGHT & RAIN SENSOR MALFUNCTION DETECTION FUNCTION
BCM controls the following items when LIGHT & RAIN sensor has a malfunction. M
WW-75
BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Priority DTC
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
• B2196: DONGLE NG
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni-
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
cardiagn.com
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
WW-76
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
A
ROOM)
Reference Value INFOID:0000000001116758
B
VALUES ON THE DIAGNOSIS TOOL
cardiagn.com
Lighting switch 2ND or AUTO (Light is illuminated) On
G
Lighting switch OFF Off
HL HI REQ
Lighting switch HI (Light is illuminated) On
Front fog lamp switch OFF Off H
Lighting switch 2ND or
FR FOG REQ
AUTO (Light is illuminated) Front fog lamp switch ON On
Front washer switch OFF Off
I
Ignition switch ON, and low Front washer switch ON
HL WASHER REQ
beam headlamp is ON (When headlamp washer is operat- On
ing)
J
Front wiper switch OFF STOP
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO Low K
Front wiper switch HI Hi
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper WW
ACT P
stop position
Front wiper operates normally Off
WIP PROT Ignition switch ON M
Front wiper stops at fail-safe oper-
BLOCK
ation
ST RLY REQ When Intelligent Key is outside the vehicle, and the push switch
Off N
NOTE: is pushed
Vehicle without Intelligent Key system indi- When Intelligent Key is inside the vehicle, and the push switch is
cates only “ON”, and it does not change. On
pushed
Ignition switch OFF or ACC Off O
IGN RLY
Ignition switch ON On
Rear window defogger switch OFF Off
P
RR DEF REQ Ignition switch ON Rear window defogger switch ON
(Rear window defogger is operat- On
ing)
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close
WW-77
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
Except selector lever R position Off
REV SW
Selector lever R position On
HOOD SW Close the hood Off
NOTE:
This item is monitored only on the vehicle
with the Vehicle Security (Theft Warning) Open the hood On
system.
THFT HRN REQ Not operation Off
NOTE:
This item is monitored only on the vehicle
with the Vehicle Security (Theft Warning) Horn is activated with Vehicle Security (Theft Warning) system. On
system.
NOTE:
HORN CHIRP Off
This item is indicated, but not monitored.
Ignition switch OFF or ACC Off
IGN ON SW
Ignition switch ON On
cardiagn.com
WW-78
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
TERMINAL LAYOUT
A
cardiagn.com
G
WW
N
JPMIA0236GB
PHYSICAL VALUES O
WW-79
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
6
Ground Ground — Ignition switch ON 0V
(B)
10*1 Ground ECM relay power supply Output Ignition switch ON Battery voltage
(L/R)
cardiagn.com
14 Ignition switch OFF or ACC 0V
Ground Ignition power supply Output
(R/B) Ignition switch ON Battery voltage
• Engine running 0 - 1.0 V*1
• Ignition switch OFF
15 (For a few seconds after turning ignition switch
0.6 V*2
(Y/L)*1 Ground ECM relay control Input OFF)
(B/R)*2 Ignition switch OFF or ACC
(More than a few seconds after turning ignition Battery voltage
switch OFF)
WW-80
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
27 Engine stopped 0V
Ground Oil pressure switch Input
(W) Engine running Battery voltage D
28 Input/
— CAN-H — —
(L) Output
29 Input/ E
— CAN-L — —
(P) Output
cardiagn.com
(R) Lighting switch 2ND Battery voltage
G
32*1 Ground ETC relay power supply Output Ignition switch ON Battery voltage
(R/Y)
• Engine running H
• Ignition switch ON 0 - 1.0 V
33*1 (For 1 second after turning ignition switch ON)
Ground Fuel pump relay control Input
(B/O) Ignition switch ON
I
(More than 1 second after turning ignition switch Battery voltage
ON)
WW-81
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
• Ignition switch OFF or ACC
• Approximately 1 second or more after turning 0V
42*1 Fuel pump relay power the ignition switch ON
Ground Output
(B/Y) supply • Approximately 1 second after turning the igni-
tion switch ON Battery voltage
• Engine running
cardiagn.com
Lighting switch OFF 0V
52 Cooling fan relay-1 power When cooling fan does LO or HI operation Battery voltage
Ground Output
(W) supply When cooling fan does OFF operation 0V
53 Battery power supply
Ground Input Ignition switch OFF Battery voltage
(W/B) (Cooling fan relay)
54*5 Cooling fan relay-2 power When cooling fan does HI operation Battery voltage
Ground Input
(R) supply When cooling fan does OFF or LO operation 0V
WW-82
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Wiring Diagram - IPDM E/R - INFOID:0000000001116759
cardiagn.com
G
WW
JCMWA0420GB
WW-83
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
cardiagn.com
JCMWA0421GB
WW-84
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
cardiagn.com
G
WW
JCMWA0422GB
WW-85
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
cardiagn.com
JCMWA0423GB
WW-86
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
• The headlamp low relay turns ON when the ignition switch is turned ON
Headlamp • The headlamp low relay turns OFF when the ignition switch is turned OFF
• Headlamp high relay OFF E
• Parking lamps
• License plate lamps • The tail lamp relay turns ON when the ignition switch is turned ON
• Tail lamps • The tail lamp relay turns OFF when the ignition switch is turned OFF F
• Illuminations
• The status just before activation of fail-safe control is maintained until the ignition
cardiagn.com
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The front wiper is operated at LO speed until the ignition switch is turned OFF if the
G
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF H
Starter motor Inhibit relay OFF
Rear window defogger Rear window defogger relay OFF
I
Headlamp washer Headlamp washer relay OFF
PTC heater PTC heater relay OFF
J
Ignition relay malfunction detection function
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit. K
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
WW
DTC Ignition switch Ignition relay Tail lamp relay
— ON ON —
— OFF OFF — M
B2098: IGN RLY ON OFF ON ON (10 minutes)
B2099: IGN RLY OFF ON OFF —
N
NOTE:
The tail lamp relay is turned OFF when the ignition switch is turned ON.
cardiagn.com
WW-88
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
WIPER AND WASHER SYSTEM SYMPTOMS
Symptom Table INFOID:0000000000924455
B
CAUTION:
Perform the self-diagnosis with CONSULT-III before performing the diagnosis by symptom. Perform
the diagnosis by DTC if DTC is detected. C
cardiagn.com
• Combination switch Combination switch G
• Harness between combination switch and BCM Refer to BCS-63, "Symptom
• BCM Table".
• IPDM E/R H
Front wiper does not Front wiper motor (LO) circuit
• Harness between IPDM E/R and front wiper
operate. LO and INT Refer to WW-25, "Compo-
motor
nent Function Check".
• Front wiper motor
I
Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
• Combination switch Combination switch J
• Harness between combination switch and BCM Refer to BCS-63, "Symptom
• BCM Table".
INT only
Front wiper request signal K
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
SYMPTOM DIAGNOSIS WW
HI, LO, and INT “FRONT WIPER DOES NOT OPERATE”
Refer to WW-93, "Diagnosis Procedure".
WW-89
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
Combination switch
• Combination switch
Refer to BCS-63, "Symptom
• BCM
Table".
HI only Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
IPDM E/R —
Combination switch
• Combination switch
Refer to BCS-63, "Symptom
• BCM
Front wiper does not Table".
stop. LO only Front wiper request signal
IPDM E/R DATA MONITOR
• BCM
"FR WIP REQ"
• IPDM E/R
IPDM E/R —
Combination switch
• Combination switch
Refer to BCS-63, "Symptom
• BCM
Table".
INT only
Front wiper request signal
IPDM E/R DATA MONITOR
cardiagn.com
• BCM
"FR WIP REQ"
• IPDM E/R
• Combination switch Combination switch
Intermittent adjustment • Harness between combination switch and BCM Refer to BCS-63, "Symptom
cannot be performed. • BCM Table".
BCM —
Intermittent control
linked with vehicle Check the vehicle speed detection wiper setting.
speed cannot be per- Refer to WW-17, "WIPER : CONSULT-III Function (BCM - WIPER)".
formed.
WW-90
WIPER AND WASHER SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS >
Symptom Probable malfunction location Inspection item
A
Rear wiper motor circuit
• Combination switch
ON only Refer to WW-34, "Compo-
• BCM
Rear wiper does not nent Function Check".
stop. Combination switch B
• Combination switch
INT only Refer to BCS-63, "Symptom
• BCM
Table".
• Combination switch Combination switch C
Wiper is not linked to • Harness between rear wiper motor and BCM Refer to BCS-63, "Symptom
the washer operation. • BCM Table".
BCM — D
Rear wiper does not
return to the Stop posi-
tion (Stops after a five- Rear wiper auto stop signal
Rear wiper does not second operation). • BCM E
circuit
operate normally. • Harness between rear wiper motor and BCM
Rear wiper stops after Refer to WW-36, "Compo-
• Rear wiper motor
operating for five sec- nent Function Check".
onds when ignition F
switch is turned ON.
Rear wiper does not
cardiagn.com
Reverse switch signal (CAN communication)
operate even when se- IPDM E/R DATA MONITOR G
• BCM
lector lever is shifted to “REV SW”
• IPDM E/R
the “R”.
• Combination switch
Combination switch H
• Harness between combination switch and BCM
Refer to BCS-63, "Symptom
• BCM
Table".
• Headlamp washer pump
• Fusible link I
• Harness between fusible link and headlamp
Headlamp washer washer relay
does not operate with • Headlamp washer relay
Headlamp washer J
the front washer when • Harness between headlamp washer relay and
does not operate. Headlamp washer circuit
headlamps are turned IPDM E/R
Refer to WW-39, "Compo-
ON. • IPDM E/R
nent Function Check".
• Harness between headlamp washer relay and
headlamp washer pump
K
• Harness between headlamp washer pump and
ground
• Headlamp washer pump WW
BCM —
WW-91
NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
Description INFOID:0000000000924458
cardiagn.com
WW-92
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
A
Description INFOID:0000000000924456
The front wiper does not operate under any operation conditions. B
Diagnosis Procedure INFOID:0000000000924457
cardiagn.com
Is front wiper operation normally?
G
YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK FRONT WIPER MOTOR FUSE H
1. Turn the ignition switch OFF.
2. Check that the front wiper motor 30A fuse (#44) is not fusing.
Is the fuse fusing? I
YES >> Replace the fuse after repairing the applicable circuit.
NO >> GO TO 3.
3.CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT J
WW-93
FRONT WIPER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
Terminals
Test item
(+) (−) Voltage
IPDM E/R (Approx.)
FRONT WIP-
Connector Terminal ER
Battery
LO
7 Ground voltage
OFF 0V
E10
Battery
HI
8 voltage
OFF 0V
Is the measurement value normal?
YES >> Replace front wiper motor.
NO >> Replace IPDM E/R.
5.CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1. Select "FR WIP REQ" of IPDM E/R data monitor item.
cardiagn.com
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the status of "FR WIP REQ".
Monitor
Monitor item Condition
status
ON HI
Front wiper switch HI
OFF STOP
FR WIP REQ
ON LOW
Front wiper switch LO
OFF STOP
Is the status of item normal?
YES >> Replace IPDM E/R.
NO >> GO TO 6.
6.CHECK COMBINATION SWITCH
1. Perform the inspection of the combination switch. Refer to BCS-63, "Symptom Table".
Is combination switch normal?
YES >> Replace BCM. Refer to BCS-64, "Exploded View".
NO >> Repair or replace the applicable parts.
WW-94
HEADLAMP WASHER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
HEADLAMP WASHER DOES NOT OPERATE
A
Description INFOID:0000000001115040
cardiagn.com
Is the status of item normal? G
YES >> Refer to WW-39, "Component Function Check".
NO >> GO TO 2.
H
2.CHECK COMBINATION SWITCH
1. Perform the inspection of the combination switch. Refer to BCS-63, "Symptom Table".
Is combination switch normal? I
YES >> Replace BCM. Refer to BCS-64, "Exploded View".
NO >> Repair or replace the applicable parts.
J
WW
WW-95
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000001102412
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRC and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRC section.
cardiagn.com
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
Precaution for Procedure without Cowl Top Cover INFOID:0000000001102413
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
PIIB3706J
WW-96
HEADLAMP WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR A
HEADLAMP WASHER NOZZLE AND TUBE
Exploded View INFOID:0000000000926336
B
cardiagn.com
JPLIA0293ZZ
G
WW
JPLIA0292ZZ
N
1. Headlamp washer nozzle assembly 2. Headlamp washer tube 3. Headlamp washer tube joint
(LH)
4. Headlamp washer nozzle assembly O
(RH)
: Clip
P
Removal and Installation INFOID:0000000000926337
REMOVAL
1. Remove the front bumper fascia. Refer to EXT-11, "Exploded View".
2. Remove headlamp washer tube from headlamp washer nozzle assembly.
WW-97
HEADLAMP WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
3. Push pawl (A), and remove headlamp washer nozzle cover (1).
: Vehicle front
JPLIA0294ZZ
4. Push pawl, and remove headlamp washer nozzle assembly from the front bumper fascia.
INSTALLATION
Note the following, and install in the reverse order of removal.
Inspection INFOID:0000000000906858
cardiagn.com
Check that the headlamp washer injection is certainly on the headlamp (LO) illuminating area. If the injection is
out of the area, check the headlamp washer tube and headlamp washer nozzle leakages.
JPLIA0295ZZ
WW-98
WASHER TANK
< ON-VEHICLE REPAIR >
WASHER TANK
A
Exploded View INFOID:0000000000896788
JPLIA0270ZZ
cardiagn.com
1. Washer tank inlet 2. Washer tank G
H
REMOVAL
1. Remove the clip (A).
I
: Vehicle front
JPLIA0271ZZ
WW
2. Pull out the washer tank inlet from the washer tank.
3. Remove the splash guard. Refer to EXT-21, "Exploded View".
4. Remove the fender protector RH (front). Refer to EXT-21, "Exploded View". M
5. Disconnect washer pump connector.
6. Disconnect headlamp washer pump connector.
N
7. Remove all washer tubes.
8. Remove washer tank mounting bolts.
9. Remove the washer tank from the vehicle. O
INSTALLATION
Install in the reverse order of removal.
CAUTION: P
Add water up to the top of the washer tank inlet after installing. Check that there is no leakage.
WW-99
WASHER PUMP
< ON-VEHICLE REPAIR >
WASHER PUMP
Exploded View INFOID:0000000000896790
JPLIA0272ZZ
cardiagn.com
1. Washer pump connector 2. Front washer tube 3. Rear washer tube
4. Washer pump 5. Packing 6. Washer tank
: Vehicle front
REMOVAL
1. Remove the splash guard. Refer to EXT-21, "Exploded View".
2. Remove the fender protector RH (front). Refer to EXT-21, "Exploded View".
3. Disconnect washer pump connector.
4. Remove front washer tube and rear washer tube.
5. Remove washer pump from the washer tank.
6. Remove the packing from the washer tank.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Never twist the packing when installing the washer pump.
WW-100
HEADLAMP WASHER PUMP
< ON-VEHICLE REPAIR >
HEADLAMP WASHER PUMP
A
Exploded View INFOID:0000000000936071
JPLIA0291ZZ
cardiagn.com
1. Headlamp washer pump connector 2. Headlamp washer pump 3. Headlamp washer tube G
4. Packing 5. Washer tank
: Vehicle front
H
Removal and Installation INFOID:0000000000936072
REMOVAL I
1. Remove the splash guard. Refer to EXT-21, "Exploded View".
2. Remove the fender protector RH (front). Refer to EXT-21, "Exploded View".
J
3. Disconnect the headlamp washer pump connector.
4. Remove headlamp washer tube.
5. Remove headlamp washer pump from the washer tank. K
6. Remove the packing from the washer tank.
INSTALLATION
Install in the reverse order of removal. WW
CAUTION:
Never twist the packing when installing the washer pump.
M
WW-101
FRONT WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
FRONT WASHER NOZZLE AND TUBE
Hydraulic Layout INFOID:0000000000896792
cardiagn.com
JPLIA0273ZZ
1. Front washer nozzle (LH) 2. Check valve 3. Front washer nozzle (RH)
4. Front washer tube 5. Washer tank
: Clip
REMOVAL
1. Open the hood.
2. Remove front washer nozzle in numerical order shown in the fig-
ure.
3. Remove the front washer tube from the front washer nozzle.
: Vehicle front
JPLIA0274ZZ
INSTALLATION
Install in the reverse order of removal.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment INFOID:0000000000926151
INSPECTION
Washer Nozzle Inspection
WW-102
FRONT WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking. A
JPLIA0275ZZ
D
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure. E
cardiagn.com
G
NOTE:
Check the width is within the limit as it cannot be adjusted.
JPLIA0276ZZ H
JPLIA0277ZZ
WW
WW-103
FRONT WIPER ARM
< ON-VEHICLE REPAIR >
FRONT WIPER ARM
Exploded View INFOID:0000000000924466
cardiagn.com
JPLIA0278GB
1. Front wiper blade (RH) 2. Front wiper arm (RH) 3. Front wiper blade (LH)
4. Front wiper arm (LH) 5. Front wiper arm cap
Refer to GI-4, "Components" for symbols in the figure.
REMOVAL
1. Operate the front wiper to move it to the auto stop position.
2. Open the hood.
3. Remove front wiper arm caps.
4. Remove the front wiper arm mounting nuts.
5. Raise front wiper arm, and remove front wiper arm from the vehicle.
INSTALLATION
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
ELH0717D
2. Operate the front wiper motor to move the front wiper to the auto stop position.
3. Adjust the front wiper blade position. Refer to WW-105, "Adjustment".
4. Install the front wiper arm by tightening the mounting nut.
5. Inject the washer fluid.
6. Operate the front wiper to move it to the auto stop position.
7. Check that the front wiper blades stop at the specified position.
8. Install wiper arm cap.
WW-104
FRONT WIPER ARM
< ON-VEHICLE REPAIR >
Adjustment INFOID:0000000000924468
A
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover and the top of front wiper blade center
Standard clearance
B
R : 57.5 ± 10.3 mm (2.26 ± 0.406 in)
L : 56.1 ± 10.3 mm (2.21 ± 0.406 in)
C
E
JPLIA0082ZZ
cardiagn.com
G
WW
WW-105
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
LHD MODELS
LHD MODELS : Exploded View INFOID:0000000000924469
REMOVAL VIEW
cardiagn.com
JPLIA0279ZZ
DISASSEMBLY VIEW
JPLIA0280ZZ
REMOVAL
1. Remove front wiper arm. Refer to WW-104, "Exploded View".
2. Remove cowl top cover. Refer to EXT-19, "Exploded View".
WW-106
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
3. Remove bolts from the front wiper drive assembly.
4. Disconnect the front wiper motor connector. A
5. Remove front wiper drive assembly from the vehicle.
INSTALLATION B
1. Install the front wiper drive assembly to the vehicle.
2. Connect the front wiper motor connector.
3. Operate the front wiper to move it to the auto stop position. C
4. Install the cowl top cover. Refer to EXT-19, "Exploded View".
5. Install front wiper arms. Refer to WW-104, "Exploded View".
D
LHD MODELS : Disassembly and Assembly INFOID:0000000000924471
DISASSEMBLY E
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the front wiper
F
linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
cardiagn.com
wiper frame.
G
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position. H
3. Disconnect the front wiper motor connector.
4. Install front wiper motor to front wiper frame.
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame. I
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Do not drop front wiper motor or cause it to come into contact with other parts. J
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply multi−purpose grease or an equivalent if necessary.
RHD MODELS K
WW
REMOVAL VIEW
JPLIA0296ZZ
WW-107
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
DISASSEMBLY VIEW
cardiagn.com
JPLIA0298GB
REMOVAL
1. Remove front wiper arm. Refer to WW-104, "Exploded View".
2. Remove cowl top cover. Refer to EXT-19, "Exploded View".
3. Remove bolts from the front wiper drive assembly.
4. Disconnect the front wiper motor connector.
5. Remove front wiper drive assembly from the vehicle.
INSTALLATION
1. Install the front wiper drive assembly to the vehicle.
2. Connect the front wiper motor connector.
3. Operate the front wiper to move it to the auto stop position.
4. Install the cowl top cover. Refer to EXT-19, "Exploded View".
5. Install front wiper arms. Refer to WW-104, "Exploded View".
RHD MODELS : Disassembly and Assembly INFOID:0000000000949932
DISASSEMBLY
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Do not bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position.
WW-108
FRONT WIPER DRIVE ASSEMBLY
< ON-VEHICLE REPAIR >
3. Disconnect the front wiper motor connector.
4. Install front wiper motor to front wiper frame. A
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION: B
• Do not drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the wiper motor and wiper linkage joint (retainer). Apply
multi−purpose grease or an equivalent if necessary. C
cardiagn.com
G
WW
WW-109
RAIN SENSOR
< ON-VEHICLE REPAIR >
RAIN SENSOR
Exploded View INFOID:0000000000906861
cardiagn.com
WW-110
WIPER AND WASHER SWITCH
< ON-VEHICLE REPAIR >
WIPER AND WASHER SWITCH
A
Exploded View INFOID:0000000001083113
JPLIA0311ZZ
cardiagn.com
1. Wiper & washer switch G
A. Pawl
REMOVAL
1. Remove steering column cover. Refer to IP-11, "Exploded View". I
2. While pressing pawls, pull the wiper & washer switch. And disconnect from the switch base.
INSTALLATION J
Installation is the reverse order of removal.
WW
WW-111
REAR WIPER MOTOR
< ON-VEHICLE REPAIR >
REAR WIPER MOTOR
Exploded View INFOID:0000000000926247
REMOVAL VIEW
cardiagn.com
JPLIA0290ZZ
REMOVAL
1. Operate the rear wiper to the auto stop position.
2. Remove rear wiper arm cover.
3. Remove the rear wiper arm mounting nut.
4. Raise rear wiper arm, and remove wiper arm from the vehicle.
5. Remove back door trim finisher lower. Refer to INT-26, "Exploded View".
6. Disconnect the rear wiper motor connector.
7. Remove bolts.
8. Remove rear wiper motor from the vehicle.
9. Remove pivot seal.
INSTALLATION
1. Install the pivot seal.
2. Install the rear wiper motor to the vehicle.
3. Connect the rear wiper motor connector.
4. Operate the rear wiper to the auto stop position.
5. Install the back door trim finisher lower. Refer to INT-26, "Exploded View".
WW-112
REAR WIPER MOTOR
< ON-VEHICLE REPAIR >
6. Clean wiper arm mount as shown in the figure to prevent nut
from being loosened. A
SKIA0082J
D
7. Operate the rear wiper motor to the auto stop position.
8. Adjust the rear wiper blade position. Refer to WW-113, "Adjustment".
9. Install the rear wiper arm by tightening the mounting nut. E
10. Inject the washer fluid.
11. Operate the rear wiper to the auto stop position.
12. Check that the rear wiper blades stop at the specified position. F
13. Install rear wiper arm cover.
cardiagn.com
Adjustment INFOID:0000000000926251 G
WW
JPLIA0289ZZ
O
WW-113
REAR WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
REAR WASHER NOZZLE AND TUBE
Hydraulic Layout INFOID:0000000000926252
cardiagn.com
JPLIA0283ZZ
REMOVAL
1. Remove the high-mounted stop lamp. Refer to EXL-183, "Exploded View".
2. Remove the rear washer tube from the rear washer nozzle.
WW-114
REAR WASHER NOZZLE AND TUBE
< ON-VEHICLE REPAIR >
3. Push pawl (A), and remove the rear washer nozzle (1) from the
high-mounted stop lamp. A
JPLIA0284ZZ
D
INSTALLATION
Install in the reverse order of removal.
E
Inspection INFOID:0000000000936394
INSPECTION
F
Washer Nozzle Inspection
Check that air can pass through the hose by blowing forward (toward
cardiagn.com
the nozzle), and check that air cannot pass through by sucking. G
JPLIA0285ZZ
φ (Spray position
Spray position h (Height) I (width) WW
area)
A 43 (1.69) 93.6 (3.69) 30 (1.18)
NOTE: M
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin. JPLIA0286ZZ
WW-115