StructDesign (GFSST - LRFD - TIA222G) 3GT-40-330C-Z-350C

DITO TELECOMMUNITY
Structural Investigation Report of

Three-Legged Self-Supporting Tower
Project Name: Design of a 40m High 3-Legged

Telecommunication Tower
Site Code: 3GT-40-330C-Z (350C)
Site Address: -
0 12/23/21 Structural design of the proposed

three-legged self-supporting tower
structure.
Rev. Date Pages Description Approved Date
REVISIONS APPROVALS
Author Discipline Work Type Document Number Revision
MEG Structural Design - 0

DITO TELECOMMUNITY DESIGN OF A 40M HIGH 3-LEGGED TELECOMMUNICATION TOWER
- STRUCTURAL INVESTIGATION REPORT FOR THREE-LEGGED SELF-SUPPORTING TOWER
TABLE OF CONTENTS
1 C E R T I F I C A T I O N ................................................................................................ 2
2 DESIGN PARAMETERS AND CRITERIA .............................................................................. 3
2.1 Units of Measurement and Language 3
2.2 Applicable Codes, References and Standards 3
2.3 Structural Steel 3
2.3.1 Plates 3
2.3.2 Bolts 3
2.3.3 Corrosion Protection and Electrodes 4
2.3.4 Slenderness Ratio, KL/r 4
2.4 Reinforced Concrete 4
2.5 Displacements 4
2.6 Design Loads 4
2.6.1 Gravity Loads 4
2.6.1 Lateral Forces 5
2.6.2 Other Design Reaction Loads from Appurtenances and Ancillaries 7
2.7 Loading Combinations 7
3 DESIGN REPORT ...................................................................................................... 9
3.1 Introduction 9
3.2 Scope of Work 9
3.3 Structure Description 9
3.3.1 Configuration and Profile 9
3.3.2 Structure Analysis 10
3.3.3 Structural System 11
3.3.4 Analysis and Assumptions Made 11
3.4 Results and Findings 12
3.4.1 Existing Tower Structure and its Member Profile Evaluation 12
3.5 Conclusion and Recommendations 13
3.5.1 Concrete Pedestal and Base Plate Assembly 13
3.5.2 Feasibility of Additional Antenna Loadings 13
4 DESIGN COMPUTATIONS .......................................................................................... 14

4.1 OPEN TOWER DESIGNER REPORT 14
5 CONDITION OF ANALYSIS ......................................................................................... 15
6 REFERENCES ........................................................................................................ 16
StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C -1- Marjie S. Erispe-Gadon

Date: 23 December 2021 Civil/Structural Engineer
1 CERTIFICATION
DITO TELECOMMUNITY
PROJECT: DESIGN OF A 40M HIGH 3-LEGGED TELECOMMUNICATION TOWER
SUBJECT: CERTIFICATION OF STRUCTURAL STABILITY – PROPOSED THREE-LEGGED SELF-SUPPORTING
TOWER
This is to certify that after a thorough review by performing structural analysis and design of the following:
 Existing three-legged self-supporting tower structure as herein described to carry the following existing and
proposed antenna loads as presented in the structural investigation report enclosed with this certification;
Qty Antenna Type Antenna Size, m Elev., m AGL Antenna Status
3 L700 2ports 18.5dbi 2.580x0.550x0.146 38.5 proposed
3 T2020L6R011 2.090x0.499x0.199 38.5 proposed
3 AAU-NR-64TR 0.85x0.47x0.17 35.5 proposed
9 RRU-2.6G-8T8R 0.48x0.356x0.14 38.5/35.5 proposed
2 MW Ø0.60 33.0 proposed
the subject self-supporting tower structure - satisfactorily meets the strength and serviceability requirements based
on the NSCP Vol. 1, National Structural Code of the Philippines Vol. 1, 7th Edition, 2015wind load provisions for
Exposure C Category and basic wind speed of 350 kph in to sustain the applied loads as indicated in the survey
data/drawing. A structural analysis and design is presented in the structural investigation report, which forms part
of this certification to affirm the structural stability of the self-supporting tower structure as described above.
However, any further loads applied on the self-supporting tower structure that are not included in the above stated
loadings, in addition to the existing antenna attachments, as reflected on the proposed antenna plan / data furnished
by DITO TELECOMMUNITY and on the structural investigation report shall be beyond the scope and responsibility of
the undersigned.
This certification is being issued for the intended facility location with site ID: 3GT-40-330C-Z (350C) for whatever
technical purpose it may serve.
ENGR. MARJIE S. ERISPE-GADON

Structural Design Engineer
PRC # : 110529
TIN # : 246-180-115
PTR # : 2577628
Date : 1.8.2021 Place: Tobias Fornier, Antique
StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 2 Marjie S. Erispe-Gadon

2 DESIGN PARAMETERS AND CRITERIA

The following is the design criteria considered in the structural investigation and evaluation of the existing
three-legged self-supporting tower structure for 3GT-40-330C-Z (350C) located in -.
2.1 Units of Measurement and Language
All units of measurement for design work, drawings and calculations shall be in the Metric System, unless
otherwise noted.
All drawings, calculation sheets, and documents shall be written in English.
2.2 Applicable Codes, References and Standards
The requirements contained in the latest edition of the following codes and standards shall form a part of
these CRITERIA, in the manner and to the Extent specified herein.
The following codes will govern the structural analysis and design:
 NSCP C101-15 National Structural Code of the Philippines Vol. 1, 7th Edition, 2015
 TIA-222-G Telecommunication Industry Association TIA_EIA 222-G1 2005 Manual
 AISC Manual of Steel Construction, “Specification for Design Fabrication and Erection of Structural
Steel ” 15th Edition, 2016
 ACI American Concrete Institute ACI-318-14M “Building Code Requirements for Concrete Works”
 AWS D1.1 American Welding Society, “Welding Design and Procedures”
 NBCP “National Building Code of the Philippines”
 IBC “International Building Code” 2006
The following standards will govern the materials of construction, as may be applicable:
 ASTM A53 Standard Specification for Steel Pipe
 ASTM A36 Standard Specification for Structural Steel
 ASTM A325 Standard Specification for High-Strength Bolts
 PNS Philippine National Standard
2.3 Structural Steel
All structural steel members and framing system shall comply with all applicable code requirements of
Chapter 5, NSCP C101-15 and/or Section 4, ANSI/TIA-222-G-2005.
Structural steel shall conform to applicable material standards with minimum specified yield strength of
248 MPa for W-, H-, I-, C-, S-shaped section; 345 MPa for angular section (width larger than 90 mm, GB
1591 Grade 16Mn) and 245 MPa for angular section (width smaller than 100 mm); 345 MPa for tubular/pipe
section used as leg members and 235 MPa for tubular/pipe section for other than leg members.
Minimum Thickness. Regardless of the stresses of the member, a minimum thickness of 3.50-mm of a
member plus 0.50-mm allowance for corrosion shall be used. A total of 4.00-mm thickness shall be
required.
2.3.1 Plates
Steel plates shall conform to applicable material standards with minimum specified yield strength of 248
MPa for (ASTM A36) or 235 MPa for (GB 700 Grade Q235).
2.3.2 Bolts
Holding-down bolts for anchoring on metal material shall be specified as conforming to ASTM A325 Type 3
or equivalent.
Holding-down bolts for anchoring on concrete shall be specified as conforming to ASTM A572 Grade 60 or
equivalent.
Bolts for structural steel connections shall conform to ASTM A325 Type 3 or equivalent.

Joint Strength. For a two-dimensional and three-dimensional framing system the full strength of the
members at the joint shall be used, except for members whose full strength over its actual stress is greater
than 1.50. In this case, the actual strength shall be used.
Welded Connection. Full weld connections shall be used in all joints with its corresponding joint strength
requirements.
2.3.3 Corrosion Protection and Electrodes
 Welding Electrodes shall be of class E70XX.
 Hot-dipped galvanization shall be 85 microns.
2.3.4 Slenderness Ratio, KL/r
The slenderness ratio, KL/r, shall preferably not exceed:
 200 for main legs;
 240 for main compression members other than leg members;
 250 for secondary members; and
 300 for tension members, except for tension rod bracing and cables.
2.4 Reinforced Concrete
 Concrete compressive strength: Concrete cylinder compressive strength measured will be:
Footings and pedestals: f’c = 21 MPa, unless noted otherwise
 Reinforcing Steel for Concrete
Reinforcing bars yield strength: Reinforcement bars minimum specified yield strength measured will
be:
Footings, Tie Beams (if any) and Pedestals:
fy = 275 MPa for Ø16 up to Ø20 deformed bars, unless noted otherwise
fy = 275 MPa for Ø25 deformed bars and larger, unless noted otherwise
Ties, Stirrups:
fy = 275 MPa for Ø10 and Ø12 deformed bars, unless noted otherwise
2.5 Displacements
Maximum displacements at the extreme critical nodes on the structure (tilt and twist/twist and sway) shall
be calculated using the Open Tower software. (See Node Displacement summary). The maximum twist and
sway shall not exceed the minimum translational and/or rotational displacement of 1.0-degree.
2.6 Design Loads
The following loads shall be considered in this report:
2.6.1 Gravity Loads
 Dead Load, D. Dead load means the weight of the structure itself.
Unit weights of major construction materials shall be as follows:
Reinforced Concrete 24 kN/m³

Plain Concrete, lean 17 kN/m³
Structural Steel 77 kN/m³
Unit weights other than the above shall conform to National Structural Code of the Philippines
(NSCP National Structural Code of the Philippines Vol. 1, 7th Edition, 2015).
 Superimposed DL on platform = 1.50 kN/m²
 Live Load, L. Live load means the load not permanently fixed to the structure.
 Superimposed LL on platform = 1.00 kN/m²

2.6.1 Lateral Forces

 Wind Load, W. Wind load on structure shall be calculated in accordance with the formula as given
in Section 207, NSCP C101-15 / TIA-222-G-2005; while, wind load on appurtenances shall be
calculated in accordance with the formula as given in Section 2.6, ANSI/TIA-222-G-2005.
The horizontal force (F) applied to each section of the structure shall be calculated from the
equation:
𝐹𝐹 = 𝑞𝑞𝑧𝑧 𝐺𝐺ℎ (EPA)s in kN (Article 2.6.9.1, ANSI/TIA-222-G-2005)
where,
𝑞𝑞𝑧𝑧 = 0.613𝐾𝐾𝑍𝑍 𝐾𝐾𝑍𝑍𝑍𝑍 𝐾𝐾𝑑𝑑 𝑉𝑉𝑠𝑠𝑠𝑠 2 𝐼𝐼 in N/m2 ; 𝑉𝑉𝑠𝑠𝑠𝑠 𝑖𝑖𝑖𝑖 𝑚𝑚/𝑠𝑠 (eq. Section 2.6.9.6, ANSI/TIA − 222 − G − 2005)
= velocity pressure evaluated at height 𝒛𝒛.
𝑲𝑲𝒁𝒁 = velocity pressure exposure coefficient based on Article 2.6.5.2, ANSI/TIA-222-G-2005
𝑲𝑲𝒁𝒁𝒁𝒁 = topographic factor defined based on Section 207A.8 and Figure 207A.8-1 NSCP C101-15 for
Topo Category 1 and Table 2-4, ANSI/TIA-222-G-2005 for Topo Category 2-4
𝑲𝑲𝒅𝒅 = wind directionality factor based on Table 2-2, ANSI/TIA-222-G-2005
𝑉𝑉𝑠𝑠𝑠𝑠 = �(𝑉𝑉𝑠𝑠𝑠𝑠 2 /(1.6 ∗ 𝐼𝐼𝑤𝑤 )) ,based on Design Manual for Wind Load Provisions of NSCP C101-15
3second gust wind speed at 10m above ground in Exposure C as defined in 2.6.5.1 for a 50-year mean
recurrence interval, where 𝑽𝑽𝒔𝒔𝒔𝒔 = wind speed whose value may be taken as 350 kph for Occupancy
Category I (Table 103-1 Essential Facilities), refer to Figure 207A.5-1A Basic Wind Speeds for Occupancy
Category I and II Buildings and Other Structure, in kph
𝑰𝑰𝒘𝒘 = Importance factor based on Table 2-1 and Table 2-3, ANSI/TIA-222-G-2005, taken as equal to
1.00 for Class II: “Structures used for services that may be provided by other means such as: commercial
wireless communications; television and radio broadcasting; cellular, PCS, CATV, and
microwave communications” in this report.
𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬𝑬 𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪𝑪 = C based on NSCP Section 207A.7 or Article 2.6.5, ANSI/TIA-222-G-2005 .
𝒛𝒛 = height above ground level, in m
𝐺𝐺 = gust-effect factor, Article 2.6.7.1, ANSI/TIA-222-G-2005
(𝐸𝐸PA)𝑠𝑠 = 𝐶𝐶𝑓𝑓[𝐷𝐷𝑓𝑓 Ʃ𝐴𝐴𝑓𝑓 + 𝐷𝐷𝑟𝑟 Ʃ(𝐴𝐴𝑟𝑟𝑅𝑅𝑟𝑟)] Article 2.6.9.1.1, ANSI/TIA-222-G-2005
= effected projected area of structural components, in m2
𝑪𝑪𝒇𝒇 = structure force coefficient; which can be determined by the following expressions:
𝐶𝐶𝑓𝑓 = 4.0𝜀𝜀2 − 5.9𝜀𝜀 + 4.0 for square tower cross section
𝐶𝐶𝑓𝑓 = 3.4𝜀𝜀2 − 4.7𝜀𝜀 + 3.4 for triangular tower cross section

(𝐴𝐴𝑓𝑓 + 𝐴𝐴𝑟𝑟 )
𝜺𝜺 = solidity ratio of solid =
𝐴𝐴𝑔𝑔
𝐴𝐴𝑓𝑓 = projected area of flat structural components in one face of the section, in m2
𝐴𝐴𝑟𝑟 = projected area of round structural components in one face of the section, in m2
𝑨𝑨𝒈𝒈 = projected area of gross section of one face as if the face were solid, in m2
Df = wind direction factor for flat structural components determined from Table 2-6
Dr = wind direction factor for round structural components determined from Table 2-6
Rr = reduction factor for a round element
= 0.36 + 0.26ε + 0.97ε2 - 0.63ε3 when C > 8.7 for no-ice conditions (supercritical flow)
where:
C = [𝑰𝑰𝒘𝒘 𝐾𝐾𝑍𝑍 𝐾𝐾𝑍𝑍𝑍𝑍 ]1/2 𝑉𝑉𝑠𝑠𝑠𝑠 D
D = outside diameter of the structural component without ice, m
 Earthquake Load, E. Earthquake or seismic load may be considered as lateral forces that shall act
non-concurrently in the direction of each principal axis of the structure. These loads are actually
dynamic forces that shall be used, among which, for structures 60-m or more in height. However,
an alternative static lateral force is recommended based on rational analysis of well-established
principles of mechanic.
Earthquake load shall be calculated in accordance with the formula as given in Section 208 NSCP and
using Open Tower software.
Design Base Shear. The total design base shear in a given direction shall be determined from the
following equation:
𝐶𝐶𝑣𝑣 𝐼𝐼
𝑉𝑉 = 𝑊𝑊 in kN (eq. 208-8 NSCP C101-15)
𝑅𝑅𝑅𝑅
The total design base shear need not exceed the following equation:
2.5𝐶𝐶𝑎𝑎 𝐼𝐼
𝑅𝑅
The total design base shear shall not be less than the following equation:
𝑉𝑉 = 0.11𝐶𝐶𝑎𝑎 𝐼𝐼𝐼𝐼 in kN (eq. 208-10 NSCP C101-15)
In addition, for structure situated in seismic Zone 4, the total base shear shall not be less than the
following equation:
0.8𝑍𝑍𝑍𝑍𝑣𝑣 𝐼𝐼
𝑅𝑅
where:
𝑰𝑰 = seismic occupancy importance factor, taken as equal to 1.00 per Table 208-1
NSCP C101-15 for building structure (standard occupancy)
𝑪𝑪𝒂𝒂 = seismic coefficient per Table 208-7 NSCP C101-15 = 0.40𝑵𝑵𝒂𝒂
𝑪𝑪𝒗𝒗 = seismic coefficient per Table 208-8 NSCP C101-15 = 0.56𝑵𝑵𝒗𝒗
𝑵𝑵𝒂𝒂 = near-source factor per Table 208-5 NSCP C101-15 = 1.00
𝑵𝑵𝒗𝒗 = near-source factor per Table 208-6 NSCP C101-15 = 1.18
𝒁𝒁 = seismic zone factor per Table 208-3 NSCP C101-15= 0.4
𝑺𝑺𝐂𝐂 = soil profile type factor, per Table 208-2 NSCP C101-15 = SC
𝑹𝑹 = horizontal force factor depending on the type of structural system; in this case,
the value shall be taken as equal to 3.00 per Table 208-11B NSCP C101-15 for steel structure or Table
208-11A NSCP C101-15 for concrete building structure or Table 208-12 NSCP C101-15 for billboard and
signages.
𝑻𝑻 = fundamental period of structure, in second per Section 208.5.2.2 NSCP C101-15
𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑻𝑻𝑻𝑻𝑻𝑻𝑻𝑻 = per Table 208-4 NSCP C101-15
𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺𝑺 = per https://hazardhunter.georisk.gov.ph/

2.6.2 Other Design Reaction Loads from Appurtenances and Ancillaries

The following table summarizes the existing and proposed antenna loads which will be the basis of this
structural investigation report.
Qty Antenna Antenna Size, m Elev., m Antenna Link Azimuth Attached Design
Type AGL Status to Leg Criteria
marked
as
Qty Antenna Antenna Size, m Elev., m Qty - - all legs -

Type AGL
3 L700 2ports 2.580x0.550x0.146 38.5 3 - - all legs -

18.5dbi
3 T2020L6R011 2.090x0.499x0.199 38.5 3 - - all legs -
3 AAU-NR-64TR 0.85x0.47x0.17 35.5 3 - - all legs -
9 RRU-2.6G- 0.48x0.356x0.14 38.5/35.5 9 - - all legs -

8T8R
2 MW Ø0.60 33.0 2 - - A and B -
1 MW Ø1.80 31.0 1 - - B -
1 MW Ø1.20 28.0 1 - - B -
Note that the weight of and the wind force effect on the antenna holder support for the RF antenna and on
the microwave antenna supports are included in the analysis.
In addition, the three-legged self-supporting tower structure shall be analyzed, as minimum, to withstand
following appurtenance loads:
 Brackets, frames required for antenna mounting and tower accessories like cable and climbing
ladders, obstruction lights, lightning protection;
 12 coax feeder cables for RF antennas, 2 coax feeder cable per MW antenna; and/or
 Electrical distribution boards (RRU units for 3G panel antenna), power and grounding cables, load
of maintenance personnel working on the tower and equipment where applicable.
2.7 Loading Combinations
All structural members and components shall be designed for the following load combinations, whichever
produces the greater stress. It is not necessary to consider combination of load, as may be applicable,
which is obvious to produce fewer stresses than other combination of loads.
The following load combinations shall be used for member check during its service level condition.
Load Load Combination per TIA-222-G
Dead, D 1.0
Wind, W 1.0

The following load combinations shall be used for member check during its strength level condition.
Load Load Combination per TIA-222-G
Dead, D 1.20 1.20 0.90 0.90
Wind, W 1.60 - 1.60 -
Earthquake, E - 1.00 - 1.00

3 DESIGN REPORT
3.1 Introduction
This DESIGN REPORT presents the structural investigative analysis and evaluation of the members of the
existing design of the three-legged self-supporting tower structure located in -. Actual site condition with
topographic factors was not considered in the original and existing design. In order to fully assess the
structural integrity of the existing structure, a structural evaluation was requested to make a detailed
structural re-analysis, review and recommendation as to the soundness, feasibility and structural stability
of the structure.
3.2 Scope of Work
The scope of work that is performed in order to present this INVESTIGATION REPORT is based on the general
scope of work required by DITO TELECOMMUNITY, as follows:
 Structural Analysis and Design
Based on the outcome of the preliminary assessment to check the safety of the existing three-
legged self-supporting tower for the proposed antenna load, structural computations of the
existing structure to include effect of loadings from accessories and proposed attachments shall
be prepared.
3.3 Structure Description
3.3.1 Configuration and Profile
The existing three-legged self-supporting tower structure is basically mounted on individual reinforced
concrete pedestals. The structure has a nominal height of approximately 40 meters with its legs mounted
on reinforced concrete pedestals and has a tapering width of 6.95 m at the base to 2 m at the top and has
10-m vertical straight portion at the top. The structure has the following existing main member profile
configuration:
Lateral Brace Remarks(Indic

Panel, Horizontal Diagonal (Main
Panel Tower Leg / Hip Brace/ ate platform
starting (Main Member Member /
Height, m Member Secondary level whether
from top / Redundant) Redundant)
Brace rest or work)
-Lightning
brace for work Arrester
└63x63x6 main
1 5 CHS114x6 CHS76x6 platform (See
horizontal. - Work
DDD)
platform
brace for work

└63x63x6 main Work
2 5 CHS140x8 CHS76x6 platform (See
horizontal. platform
DDD)
└63x63x6 main
3 5 CHS168x10 CHS76x6 - -
horizontal.
└75x75x6 main
4 5 CHS194x10 CHS76x6 - -
horizontal.
└75x75x6 main Varies (See

5 5 CHS203x12 CHS89x6 -
horizontal. DDD)

6 5 CHS219x12 CHS89x6 -
horizontal. DDD)

7 5 CHS219x14 CHS89x6 -
horizontal. DDD)
└125x125x10 Varies (See

8 5 CHS245x14 CHS89x6 -
main horizontal. DDD)

Tower Ø640x40 thick base plate with 6-M48 anchor bolts and 270x18 thick stiffener plates
Base Plate
Base between bolts.
The structure configuration consists of predominantly x-bracing system for the entire tower. The self-
supporting tower structure is considered to be under Type 3 construction, on which the design is associated
with the member joint strength. The provisions of the NSCP, Vol. 1, National Structural Code of the
Philippines Vol. 1, 7th Edition, 2015are basically used in checking the stability of the structure members,
assessed to sustain the dead load, live load, wind and seismic forces as herein described. The investigative
analysis of the self-supporting tower structure is generated using the Open Tower software. It is used to
generate the 3D model, create all input specifications and all output reports and displays graphical
environment. These structural modelling and analysis input specifications are stored in a text file with
extension .MGB which can be analyzed and designed. The results can be viewed graphically. The MGB file
is processed by the Open Tower analysis to produce results that are stored in several files with extensions
such as OUT. The .OUT text file contains the printable output as created by the specifications. The other
files contain the results (node displacements, member / element forces, mode shapes, section forces,
section moments and section displacements, etc.).
The provisions of Section 207 of the NSCP, Vol. 1, National Structural Code of the Philippines Vol. 1, 7th
Edition, 2015(adapted from the 15thEdition of the American Institute of Steel Construction (AISC), 2016) are
basically used in checking the stability of the tower members, designed to sustain the wind velocity and
antenna attachments as herein described. A member marked “OK” signifies compliance with the AISC
combined stress criteria. Design stress results are shown as a tabulation of “MEMBER END FORCES/CHECK
CODE MEMBERS,” which are then used to check the design the members of the self-supporting tower
structure.
The self-supporting tower structure shall be analyzed having a basic wind speed of 350 kph with Exposure
C consideration. The coefficients used in the structural computation were taken from NSCP, Vol. I, Section
207, National Structural Code of the Philippines Vol. 1, 7th Edition, 2015.
In the structural investigation analysis, the members of the self-supporting tower are assumed to have
minimum specified yield strength as indicated in Section 2.3 of this report.
This report provides the detailed structural re-analysis of the existing tower for the current and additional
antenna loadings following DITO TELECOMMUNITY’s technical design requirements, governing
specifications, codes and standards. At the latter part of the report, conclusion and recommendation are
presented to guide DITO TELECOMMUNITY and its respective end users for whatever purpose this
document may serve.
Results of the analysis and design are summarized in the following pages of this report.
3.3.2 Structure Analysis
Generally, the structural modelling shall be analyzed based on the principle of
load resistance factor design (LRFD) concept. However, in this report, the load resistance factor design
(LRFD) conditions will be limited to strength and displacement requirements.
Methodology. A comprehensive load resistance factor design (LRFD) design approach will be used. Factored
load combinations will consider cases where continuously acting loads are both disadvantageous and
advantageous, with load factors adjusted as appropriate.
Where appropriate, the following computer program may be employed:
 Open Tower - Two-dimensional / three-dimensional finite element analysis.
 Design+ – General Engineering Assistance and Reference software for routine design work.
 Customized spreadsheet programs developed by the designer in conformity with the requirements
of the applicable code.
The analysis of the structure will follow standard rational code procedures.
The existing self-supporting tower structure shall be analyzed as a three-dimensional space frame subjected
to both gravity loads and primarily for horizontal loads in accordance with the applicable code of practice.

The general method used to analyze this self-supporting tower structure is based on structural program
module in structural analysis known as Open Tower Program. The program implores a computerized three-
dimensional direct element stiffness matrix method.
With this program module, the self-supporting tower structure is analyzed as a three-dimensional space
subjected to wind and seismic loads, antenna loads (existing and proposed) and self-weight of the structure.
Various Open Tower outputs can be retrieved on a completed analyzed structure. However, outputs are
limited to the most critical load variations and structural code-checking such as the AISC code-checking,
member end forces, type of material used, joint coordinates, member incidences, member - critical
condition and graphical print output.
3.3.3 Structural System
The structure is made of structural steel space frame composed of PIPE LEG AND MAIN DIAGONAL, AND
ANGULAR HORIZONTAL, LATERAL AND SECONDARY BRACES. The vertical configuration of the structure is
a three-legged self-supporting tower, the whole structure being mounted on the reinforced concrete
pedestals.
3.3.4 Analysis and Assumptions Made
A comprehensive design approach will be used. Factored load combinations will consider cases where
continuously acting loads are both disadvantageous and advantageous, with load factors adjusted as
appropriate. However, for structural steel system, alternate stress design method will be employed where
unfactored load combinations will be considered at service stage.
The analysis and evaluation of structure and its components will follow standard rational code procedures.
In the structural investigative analysis and evaluation of the existing self-supporting tower members are
assumed to have minimum yield strength as stated in the material specifications – Section 2.3 of this report.

3.4 Results and Findings

3.4.1 Existing Tower Structure and its Member Profile Evaluation
In the structural analysis and evaluation made in this report which considered the combination of loads such as the antenna loads. wind and seismic forces and self-
weight of structure, the following table in next page summarizes the findings and evaluation of the existing three-legged self-supporting tower.
Horizontal (Main Diagonal (Main Lateral Brace /

Panel Ht, Tower Leg Investigation Investigation Investigation Investigation
Panel Member / Member / Hip Brace/
m Member Remarks
Redundant)
Remarks
Redundant)
Remarks
Secondary Brace
Remarks
brace for work

└63x63x6 main
1 5 CHS114x6 Adequate. Adequate. CHS76x6 Adequate. platform (See Satisfactory.
horizontal.
DDD)
brace for work

└63x63x6 main
2 5 CHS140x8 Adequate. Adequate. CHS76x6 Adequate. platform (See Satisfactory.
horizontal.
DDD)
└63x63x6 main
3 5 CHS168x10 Adequate. Adequate. CHS76x6 Adequate. - -.
horizontal.
└75x75x6 main
4 5 CHS194x10 Adequate. Adequate. CHS76x6 Adequate. - -.
horizontal.
└75x75x6 main
5 5 CHS203x12 Adequate. Adequate. CHS89x6 Adequate. Varies (See DDD) Satisfactory.
horizontal.
└75x75x6 main
horizontal.
└75x75x6 main
horizontal.
└125x125x10 main
8 5 CHS245x14 Adequate. Adequate. CHS89x6 Varies (See DDD) Satisfactory.
horizontal.
Tower
Base Plate Ø640x40 thick base plate with 6-M48 anchor bolts and 270x18 thick stiffener plates between bolts. Adequate.
Base

3.5 Conclusion and Recommendations

3.5.1 Concrete Pedestal and Base Plate Assembly
The base plate assembly consisting of Ø640x40 thick base plate with 6-M48 anchor bolts and 270x18 thick
stiffener plates between bolts is adequate to sustain the new tower loads as considered in this report.
3.5.2 Feasibility of Additional Antenna Loadings
The following proposed antenna loads CAN be sustained by the existing three-legged self-supporting tower
structure, therefore feasible.
Qty Antenna Antenna Size, m Elev., m Antenna Link Azimuth Attached Design
Type AGL Status to Leg Criteria
marked
as
Qty Antenna Antenna Size, m Elev., m Qty - - all legs -

Type AGL
3 L700 2ports 2.580x0.550x0.146 38.5 3 - - all legs -

18.5dbi
3 T2020L6R011 2.090x0.499x0.199 38.5 3 - - all legs -
3 AAU-NR-64TR 0.85x0.47x0.17 35.5 3 - - all legs -
9 RRU-2.6G- 0.48x0.356x0.14 38.5/35.5 9 - - all legs -

8T8R
2 MW Ø0.60 33.0 2 - - A and B -
1 MW Ø1.80 31.0 1 - - B -
1 MW Ø1.20 28.0 1 - - B -

- STRUCTURAL INVESTIGATION REPORT
4 DESIGN COMPUTATIONS
4.1 OPEN TOWER DESIGNER REPORT
See attached report.

Tower Profile
Tower Summary
Tower Type 3-Leg Self-Supporting
Tower Height (m) 40
Base Elevation (m) 0.6
Bearing Angle with respect to North 0 deg
State Alaska
County Aleutians East
Latitude -
Longitude -
Active Scenario 3GT-40-CMAX-Z TAC20211216
Wind Load Parameters

Design Standard TIA-222-G
Structure Class II
Wind Speed (m/sec) 76.861
Service Wind Speed (m/sec) 26.822
Ice Wind Speed (m/sec) 0
Ice Thickness (mm) 0
Seismic Load Parameters

Design Standard TIA-222-G
Method Equivalent Lateral Force Procedure
Risk Category I
Importance Factor 1
Response Modification Factor 3.0
Site Class StiffSoil
0.75
S₁ 0.3
4
0.33013 seconds
Seismic Design Category D
Analysis Parameters
Type of Analysis Linear
Print Date:05/01/2022 OpenTower CE : 10.02.00.44 Page 1 of 36

Site Parameters
Wind Structure Exposure Topographi
Direction Class Category c Category
From True
North (deg)
All II C 1
Tower Geometry
Top Bottom
Section Range Section Length Face Diagonal Top Girt Bottom Girt
Section ID Width Width
(m) (m) Bracing Spacing (m) Offset (mm) Offset (mm)
(m) (m)
1 40-35 5.0000 K Down 1.65 2.0000 2.0000 0.0000 0.0000
2 35-30 5.0000 K Down 1.65 2.0000 2.0000 0.0000 0.0000
3 30-25 5.0000 K Down 1.65 2.0000 2.8250 0.0000 0.0000
4 25-20 5.0000 K Down 1.65 2.8250 3.6500 0.0000 0.0000
5 20-17.5 2.5000 K Up 2.5 3.6500 4.0620 0.0000 0.0000
6 17.5-15 2.5000 K Down 2.5 4.0620 4.4750 0.0000 0.0000
7 15-12.5 2.5000 K Up 2.5 4.4750 4.8870 0.0000 0.0000
8 12.5-10 2.5000 K Down 2.5 4.8870 5.3000 0.0000 0.0000
9 10-7.5 2.5000 K Up 2.5 5.3000 5.7130 0.0000 0.0000
10 7.5-5 2.5000 K Down 2.5 5.7130 6.1250 0.0000 0.0000
11 5-2.5 2.5000 K Up 2.5 6.1250 6.5380 0.0000 0.0000
12 2.5-0 2.5000 K Down 2.5 6.5380 6.9500 0.0000 0.0000
Member Properties
Section Member No Of Bolt Size

Section ID Member Class Section Profile Bolt Material
Range (m) Material Bolts (mm)
1 40-35 LEG PIP114X6.0 S 355 10 20 8.8_N
2 35-30 LEG PIP140X8.0 S 355 10 20 8.8_N
3 30-25 LEG PIP168X10.0 S 355 12 24 8.8_N
4 25-20 LEG PIP194X10.0 S 355 10 26 8.8_N
5 20-17.5 LEG PIP203X12.0 S 355 10 26 8.8_N
6 17.5-15 LEG PIP203X12.0 S 355 10 29 8.8_N
7 15-12.5 LEG PIP219X12.0 S 355 0 0 -
8 12.5-10 LEG PIP219X12.0 S 355 10 29 8.8_N
9 10-7.5 LEG PIP219X14.0 S 355 0 0 -
10 7.5-5 LEG PIP219X14.0 S 355 10 29 8.8_N
11 5-2.5 LEG PIP245X14.0 S 355 0 0 -
12 2.5-0 LEG PIP245X14.0 S 355 6 48 8.8_N
1 40-35 DIAGONAL PIP76X6.0 S 355 2 20 8.8_N

Member Properties Cont...

2 35-30 DIAGONAL PIP76X6.0 S 355 2 20 8.8_N
3 30-25 DIAGONAL PIP76X6.0 S 355 2 20 8.8_N
4 25-20 DIAGONAL PIP76X6.0 S 355 2 20 8.8_N
5 20-17.5 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
6 17.5-15 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
7 15-12.5 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
8 12.5-10 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
9 10-7.5 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
10 7.5-5 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
11 5-2.5 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
12 2.5-0 DIAGONAL PIP89X6.0 S 355 2 20 8.8_N
1 40-35 HORIZONTAL EA63X63X6 S 235 1 20 8.8_N
5 20-17.5 TOPHORIZONTAL EA75X75X6 S 355 1 20 8.8_N
6 17.5-15 HORIZONTAL EA75X75X6 S 355 1 20 8.8_N
8 12.5-10 PB1 EA63X63X6 S 235 1 16 8.8_N
1 40-35 PB2 EA50X50X5 S 235 2 20 8.8_N
1 40-35 PB3 EA63X63X6 S 235 2 20 8.8_N
1 40-35 PB2 EA63X63X6 S 235 2 20 8.8_N
2 35-30 PB2 EA50X50X5 S 235 2 20 8.8_N
2 35-30 PB3 EA63X63X5 S 235 2 20 8.8_N

Member Properties Cont...

3 30-25 PB2 EA63X63X6 S 235 2 20 8.8_N
4 25-20 PB2 EA63X63X6 S 235 2 20 8.8_N
5 20-17.5 INNERBRACING XAEs56X56X5 S 235 2 20 8.8_N
6 17.5-15 PB2 XAEs56X56X5 S 235 2 20 8.8_N
6 17.5-15 PB3 XAEs56X56X5 S 235 2 20 8.8_N
6 17.5-15 PB4 EA63X63X6 S 235 2 20 8.8_N
8 12.5-10 PB2 EA63X63X6 S 235 2 20 8.8_N
8 12.5-10 PB3 EA63X63X6 S 235 2 20 8.8_N
8 12.5-10 PB4 EA63X63X6 S 235 2 20 8.8_N
10 7.5-5 INNERBRACING EA63X63X6 S 235 2 20 8.8_N
SUBINNERBRACIN
10 7.5-5 XAEs56X56X5 S 235 2 20 8.8_N
G1
12 2.5-0 PB6 100X100X8EA S 275 2 20 8.8_N
12 2.5-0 PB7 EA63X63X6 S 235 2 20 8.8_N
12 2.5-0 PB8 EA75X75X6 S 235 2 20 8.8_N
Discrete Appurtenances
Front Side
Weig
Mt Ant Horiz. Lat. Vert. Area Area Rel.
Mount Model ht(no Ks Ks
CL CL Mfg Location Offset Offset Offset (no (no Ka Azi
Type Number ice) (fr) (Si)
(m) (m) (m) (m) (m) ice) ice) (deg)
(kg)
(m2) (m2)
UPT:L70
UPT:PANEL
39 38.5 UPT:DITO 0 2ports LegA 0 0.2 0 1.84 0.66 37.99 0.8 1 1 45
MOUNT
18.5dbi
UPT:T20
UPT:PANEL
39 38.5 UPT:DITO 20L6R01 LegA 0 -0.2 0 1.33 0.63 46.49 0.8 1 1 315
MOUNT
1
UPT:RRU
UPT:PANEL UPT:Antenn
39 38.5 -2.6G- LegA 0 0.2 0 0.21 0.08 25 0.8 1 1 225
MOUNT a
8T8R
UPT:RRU
39 38.5 -2.6G- LegA 0 -0.2 0 0.21 0.08 25 0.8 1 1 135
MOUNT a
8T8R
UPT:L70
UPT:PANEL
39 38.5 UPT:DITO 0 2ports LegB 0 0.2 0 1.84 0.66 37.99 0.8 1 1 45
MOUNT
18.5dbi

Discrete Appurtenances Cont...
Front Side
Weig
Mt Ant Horiz. Lat. Vert. Area Area Rel.
Mount Model ht(no Ks Ks
CL CL Mfg Location Offset Offset Offset (no (no Ka Azi
Type Number ice) (fr) (Si)
(m) (m) (m) (m) (m) ice) ice) (deg)
(kg)
(m2) (m2)
UPT:T20
UPT:PANEL
39 38.5 UPT:DITO 20L6R01 LegB 0 -0.2 0 1.33 0.63 46.49 0.8 1 1 315
MOUNT
1
UPT:RRU
39 38.5 -2.6G- LegB 0 0.2 0 0.21 0.08 25 0.8 1 1 225
MOUNT a
8T8R
UPT:RRU
39 38.5 -2.6G- LegB 0 -0.2 0 0.21 0.08 25 0.8 1 1 135
MOUNT a
8T8R
UPT:L70
UPT:PANEL
39 38.5 UPT:DITO 0 2ports LegC 0 0.2 0 1.84 0.66 37.99 0.8 1 1 45
MOUNT
18.5dbi
UPT:T20
UPT:PANEL
39 38.5 UPT:DITO 20L6R01 LegC 0 -0.2 0 1.33 0.63 46.49 0.8 1 1 315
MOUNT
1
UPT:RRU
39 38.5 -2.6G- LegC 0 0.2 0 0.21 0.08 25 0.8 1 1 225
MOUNT a
8T8R
UPT:RRU
39 38.5 -2.6G- LegC 0 -0.2 0 0.21 0.08 25 0.8 1 1 135
MOUNT a
8T8R
UPT:AAU
UPT:PANEL
36 35.5 UPT:DITO -NR- LegA 0 0 0 0.48 0.19 39.99 0.8 1 1 0
MOUNT
64TR
UPT:RRU
36 35.5 -2.6G- LegA 0 0 0 0.21 0.08 25 0.8 1 1 180
MOUNT a
8T8R
UPT:AAU
UPT:PANEL
36 35.5 UPT:DITO -NR- LegB 0 0 0 0.48 0.19 39.99 0.8 1 1 0
MOUNT
64TR
UPT:RRU
36 35.5 -2.6G- LegB 0 0 0 0.21 0.08 25 0.8 1 1 180
MOUNT a
8T8R
UPT:AAU
UPT:PANEL
36 35.5 UPT:DITO -NR- LegC 0 0 0 0.48 0.19 39.99 0.8 1 1 0
MOUNT
64TR
UPT:RRU
36 35.5 -2.6G- LegC 0 0 0 0.21 0.08 25 0.8 1 1 180
MOUNT a
8T8R
UPT:MWMO
33 33 UPT:DITO UPT:Φ0.6 LegA 0 0 0 0.28 0.28 37.99 1 1 1 0
UNT
UPT:MWMO
33 33 UPT:DITO UPT:Φ0.6 LegC 0 0 0 0.28 0.28 37.99 1 1 1 0
UNT
UPT:MWMO 106.9
31 31 UPT:DITO UPT:Φ1.8 LegB 0 0 0 2.54 2.54 1 1 1 0
UNT 8
UPT:MWMO
28 28 UPT:DITO UPT:Φ1.2 LegC 0 0 0 1.13 1.13 47.99 1 1 1 0
UNT
Miscellaneous Appurtenances
Side
Front
Horiz. Lat. Vert. Area Weight Rel.
MiscElv Model Area Ks Ks
Mfg Location Offset Offset Offset (no (no ice) Ka Azi
(m) Number (no ice) (fr) (Si)
(m) (m) (m) ice) (kg) (deg)
(m2)
(m2)
Miscellaneou
40 1"x12' Centroid 0 0 1.83 0.11 0.11 18.14 1 1 1 0
s

Linear Attachments
Bottom Top lateral lateral Area (no

Attachment Weight (no
Attachment model Elevation Elevation Location Offset(of Offset(leg) ice)
ID ice) (kg/m)
(m) (m) face) (mm) (m2/m)
1 Hoop-LADDER 0 40 Leg B 0.0000 0.0000 0.0860 16.3700
Linear Appurtenances
There is no data of this type
LEG SUMMARY
Tower
Section Member Pu (Comp) Pu (Tens) Capacity Ratio
Elevation ϕc Pn(kN) ϕt Pn(kN)
ID Description (kN) (kN) (%)
(m)
1 40-35 PIP114X6.0 61.8193 567.0303 52.8173 650.4221 10.9
2 35-30 PIP140X8.0 278.5835 966.9801 257.8763 1059.9477 28.81
3 30-25 PIP168X10.0 496.4474 1486.6516 467.4163 1585.9086 33.39
4 25-20 PIP194X10.0 646.4943 1760.8403 607.3151 1846.8794 36.72
5 20-17.5 PIP203X12.0 748.4875 2078.4434 702.3315 2300.5694 36.01
6 17.5-15 PIP203X12.0 749.7377 2078.4434 700.2193 2300.5694 36.07
7 15-12.5 PIP219X12.0 886.2802 2286.6881 824.6005 2493.2886 38.76
8 12.5-10 PIP219X12.0 887.487 2286.6881 822.2026 2493.2886 38.81
9 10-7.5 PIP219X14.0 1005.0911 2637.8502 928.45 2880.7303 38.1
10 7.5-5 PIP219X14.0 1006.717 2637.8502 925.8201 2880.7303 38.16
11 5-2.5 PIP245X14.0 1120.6462 3028.3416 1026.4182 3246.0913 37.01
12 2.5-0 PIP245X14.0 1123.0583 3028.3416 1023.4387 3246.0913 37.08
LEG BOLT SUMMARY

Tower Applied
Section Member Connection Pu (Comp) Pu (Tens) Connection Capacity
Elevation Force
ID Description Type (kN) (kN) Capacity (kN) Ratio (%)
(m) (kN)
1 40-35 PIP114X6.0 Flange 61.8193 52.1418 52.1418 1462.1903 3.57
2 35-30 PIP140X8.0 Flange 278.0128 257.7196 257.7196 1462.1903 17.63
3 30-25 PIP168X10.0 Flange 496.4474 466.9865 466.9865 2526.6528 18.48
4 25-20 PIP194X10.0 Flange 646.4943 606.8145 606.8145 1251.225 48.5
5 20-17.5 PIP203X12.0 Flange 748.4875 701.0843 701.0843 1251.225 56.03

LEG BOLT SUMMARY Cont...
Tower Applied
Section Member Connection Pu (Comp) Pu (Tens) Connection Capacity
Elevation Force
ID Description Type (kN) (kN) Capacity (kN) Ratio (%)
(m) (kN)
6 17.5-15 PIP203X12.0 Flange 749.7377 698.9721 698.9721 17598.0752 3.97
7 15-12.5 PIP219X12.0 0 0 0 0 0
8 12.5-10 PIP219X12.0 Flange 887.487 820.8509 820.8509 17598.0752 4.66
9 10-7.5 PIP219X14.0 0 0 0 0 0
10 7.5-5 PIP219X14.0 Flange 1006.717 924.2583 924.2583 17598.0752 5.25
11 5-2.5 PIP245X14.0 0 0 0 0 0
LEG DETAILS
Tower Fy Fu
Section Member Area
Elevation Gov. Axis K Lu (m) r (mm) KL/r (N/m (N/m
ID Description (mm2)
(m) m2) m2)
1 40-35 PIP114X6.0 z 1 1.65 38.1728 43.2245 20.3575 355 510
2 35-30 PIP140X8.0 z 1 1.65 46.6693 35.3551 33.1752 355 510
3 30-25 PIP168X10.0 z 1 1.6575 55.871 29.666 49.6372 355 510
4 25-20 PIP194X10.0 z 1 1.6575 65.0308 25.4874 57.8053 355 510
5 20-17.5 PIP203X12.0 y 1 2.5113 67.5383 37.1836 72.0053 355 510
6 17.5-15 PIP203X12.0 y 1 2.5113 67.5383 37.1836 72.0053 355 510
7 15-12.5 PIP219X12.0 x 1 2.5113 73.1745 34.3196 78.0372 355 510
8 12.5-10 PIP219X12.0 x 1 2.5113 73.1745 34.3196 78.0372 355 510
9 10-7.5 PIP219X14.0 y 1 2.5113 72.5146 34.6319 90.1637 355 510
10 7.5-5 PIP219X14.0 y 1 2.5113 72.5146 34.6319 90.1637 355 510
11 5-2.5 PIP245X14.0 y 1 2.5113 81.6713 30.7491 101.5991 355 510
12 2.5-0 PIP245X14.0 z 1 2.5113 81.6713 30.7491 101.5991 355 510
LEG BASE PLATE SUMMARY
Clear
Section Diameter Base Plate Controlling
Anchor Rod Quantity Distance Ratio Result
ID (mm) Detail Load
(mm)
12 UPT:M48_8.8_N 48 6 0 b Axial+Shear 17.86 Pass

DIAGONAL SUMMARY
Section Tower Member Pu (Comp) Pu (Tens) Capacity Ratio

ϕc Pn (kN) ϕt Pn (kN)
ID Elevation (m) Description (kN) (kN) (%)
1 40-35 PIP76X6.0 37.4153 205.5226 37.0577 421.5707 18.2
2 35-30 PIP76X6.0 67.9772 205.5226 67.6243 421.5707 33.08
3 30-25 PIP76X6.0 44.2849 198.3845 43.8876 421.5707 22.32
4 25-20 PIP76X6.0 41.6286 174.3717 40.9708 421.5707 23.87
5 20-17.5 PIP89X6.0 49.7479 196.5573 48.6873 499.861 25.31
6 17.5-15 PIP89X6.0 54.211 182.0268 51.3853 499.861 29.78
7 15-12.5 PIP89X6.0 47.6305 182.0268 48.0865 499.861 26.17
8 12.5-10 PIP89X6.0 52.5546 166.4058 51.1454 499.861 31.58
9 10-7.5 PIP89X6.0 47.3699 166.4058 47.7681 499.861 28.47
10 7.5-5 PIP89X6.0 52.9948 150.0797 50.8962 499.861 35.31
11 5-2.5 PIP89X6.0 49.4749 150.0797 50.3127 499.861 32.97
12 2.5-0 PIP89X6.0 54.2359 135.3181 51.069 499.861 40.08
DIAGONAL SEGMENT SUMMARY
Section Segment Elevation Member Pu (Comp) Pu (Tens) Capacity

Segment ID ϕc Pn (kN) ϕt Pn (kN)
ID (m) Description (kN) (kN) Ratio (%)
1 1 40-38.3 PIP76X6.0 5.163 202.9428 4.7651 421.5707 2.54
1 2 38.3-36.65 PIP76X6.0 31.8648 205.5226 31.4867 421.5707 15.5
1 3 36.65-35 PIP76X6.0 37.4153 205.5226 37.0577 421.5707 18.2
2 1 35-33.3 PIP76X6.0 50.1623 202.9428 49.7689 421.5707 24.72
2 2 33.3-31.65 PIP76X6.0 56.2631 205.5226 55.9087 421.5707 27.38
2 3 31.65-30 PIP76X6.0 67.9772 205.5226 67.6243 421.5707 33.08
3 1 30-28.3 PIP76X6.0 44.2849 198.3845 43.8876 421.5707 22.32
3 2 28.3-26.65 PIP76X6.0 43.044 196.0707 42.6165 421.5707 21.95
3 3 26.65-25 PIP76X6.0 41.9666 191.0008 41.4973 421.5707 21.97
4 1 25-23.3 PIP76X6.0 41.1662 183.4006 40.5556 421.5707 22.45
4 2 23.3-21.65 PIP76X6.0 40.2679 180.0251 39.6697 421.5707 22.37
4 3 21.65-20 PIP76X6.0 41.6286 174.3717 40.9708 421.5707 23.87
5 1 20-17.5 PIP89X6.0 49.7479 196.5573 48.6873 499.861 25.31
6 1 17.5-15 PIP89X6.0 54.211 182.0268 51.3853 499.861 29.78
7 1 15-12.5 PIP89X6.0 47.6305 182.0268 48.0865 499.861 26.17
8 1 12.5-10 PIP89X6.0 52.5546 166.4058 51.1454 499.861 31.58
9 1 10-7.5 PIP89X6.0 47.3699 166.4058 47.7681 499.861 28.47
10 1 7.5-5 PIP89X6.0 52.9948 150.0797 50.8962 499.861 35.31
11 1 5-2.5 PIP89X6.0 49.4749 150.0797 50.3127 499.861 32.97
12 1 2.5-0 PIP89X6.0 54.2359 135.3181 51.069 499.861 40.08
DIAGONAL BOLT SUMMARY
Member
Tower Edge Gage Pu Bolt Member
Section Member Pu (Tens) Block Capacity
Elevation Dist Line (Comp Shear Bearing
ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.999 37.415
1 40-35 PIP76X6.0 30 36.8813 175.9185 0 0 21.27
7 3
37.999 67.977
2 35-30 PIP76X6.0 30 66.9623 175.9185 0 0 38.64
7 2
37.999 44.284
3 30-25 PIP76X6.0 30 42.5838 175.9185 0 0 25.17
7 9
37.999 41.628
4 25-20 PIP76X6.0 30 40.7996 175.9185 0 0 23.66
7 6
44.499 49.747
5 20-17.5 PIP89X6.0 30 48.4163 175.9185 0 0 28.28
5 9
44.499
6 17.5-15 PIP89X6.0 30 54.211 51.1143 175.9185 0 0 30.82
5
44.499 47.318
7 15-12.5 PIP89X6.0 30 48.0865 175.9185 0 0 27.33
5 8

DIAGONAL BOLT SUMMARY Cont...
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
44.499 52.554
8 12.5-10 PIP89X6.0 30 50.8041 175.9185 0 0 29.87
5 6
44.499 47.098
9 10-7.5 PIP89X6.0 30 47.7681 175.9185 0 0 27.15
5 9
44.499 52.994
10 7.5-5 PIP89X6.0 30 50.6252 175.9185 0 0 30.12
5 8
44.499 49.203
11 5-2.5 PIP89X6.0 30 50.3127 175.9185 0 0 28.6
5 9
44.499 54.235
12 2.5-0 PIP89X6.0 30 50.798 175.9185 0 0 30.83
5 9
DIAGONAL BOLT SEGMENT SUMMARY
Member
Segment Edge Gage Pu Bolt Member
Section Segmen Member Pu (Tens) Block Capacity
ID t ID Description (kN) Shear Ratio (%)
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.999
1 1 40-38.3 PIP76X6.0 30 5.163 4.592 175.9185 0 0 2.93
7
37.999 31.864
1 2 38.3-36.65 PIP76X6.0 30 31.3085 175.9185 0 0 18.11
7 8
37.999 37.415
1 3 36.65-35 PIP76X6.0 30 36.8813 175.9185 0 0 21.27
7 3
37.999 50.162
2 1 35-33.3 PIP76X6.0 30 49.6135 175.9185 0 0 28.51
7 3
37.999 56.263
2 2 33.3-31.65 PIP76X6.0 30 55.7567 175.9185 0 0 31.98
7 1
37.999 67.977
2 3 31.65-30 PIP76X6.0 30 66.9623 175.9185 0 0 38.64
7 2
37.999 44.284
3 1 30-28.3 PIP76X6.0 30 42.5838 175.9185 0 0 25.17
7 9
37.999
3 2 28.3-26.65 PIP76X6.0 30 43.044 42.3622 175.9185 0 0 24.47
7
37.999 41.966
3 3 26.65-25 PIP76X6.0 30 41.2912 175.9185 0 0 23.86
7 6
37.999 41.166
4 1 25-23.3 PIP76X6.0 30 40.4002 175.9185 0 0 23.4
7 2
37.999 40.267
4 2 23.3-21.65 PIP76X6.0 30 39.5009 175.9185 0 0 22.89
7 9
37.999 41.628
4 3 21.65-20 PIP76X6.0 30 40.7996 175.9185 0 0 23.66
7 6
44.499 49.747
5 1 20-17.5 PIP89X6.0 30 48.4163 175.9185 0 0 28.28
5 9
44.499
6 1 17.5-15 PIP89X6.0 30 54.211 51.1143 175.9185 0 0 30.82
5
44.499 47.318
7 1 15-12.5 PIP89X6.0 30 48.0865 175.9185 0 0 27.33
5 8
44.499 52.554
8 1 12.5-10 PIP89X6.0 30 50.8041 175.9185 0 0 29.87
5 6
44.499 47.098
9 1 10-7.5 PIP89X6.0 30 47.7681 175.9185 0 0 27.15
5 9
44.499 52.994
10 1 7.5-5 PIP89X6.0 30 50.6252 175.9185 0 0 30.12
5 8
44.499 49.203
11 1 5-2.5 PIP89X6.0 30 50.3127 175.9185 0 0 28.6
5 9
44.499 54.235
12 1 2.5-0 PIP89X6.0 30 50.798 175.9185 0 0 30.83
5 9

DIAGONAL DETAIL
Tower Fy Fu
Section Member Area
ID Description (cm2)
(m) m2) m2)
1 40-35 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
2 35-30 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
3 30-25 PIP76X6.0 y 1.226 2.0486 24.7941 101.3121 13.1947 355 510
4 25-20 PIP76X6.0 y 1.104 2.4616 24.7941 109.6401 13.1947 355 510
5 20-17.5 PIP89X6.0 y 1.069 3.0975 29.3678 112.7371 15.6451 355 510
6 17.5-15 PIP89X6.0 y 1.025 3.3572 29.3678 117.1573 15.6451 355 510
7 15-12.5 PIP89X6.0 y 1.025 3.3572 29.3678 117.1573 15.6451 355 510
8 12.5-10 PIP89X6.0 y 0.987 3.6451 29.3678 122.5329 15.6451 355 510
9 10-7.5 PIP89X6.0 y 0.987 3.6451 29.3678 122.5329 15.6451 355 510
10 7.5-5 PIP89X6.0 y 0.958 3.9551 29.3678 129.0257 15.6451 355 510
11 5-2.5 PIP89X6.0 y 0.958 3.9551 29.3678 129.0257 15.6451 355 510
12 2.5-0 PIP89X6.0 y 0.932 4.2825 29.3678 135.8811 15.6451 355 510
DIAGONAL DETAIL SEGMENT

Segment
Section Segment Member Area Fy Fu
Elevation Gov. Axis K Lu (m) r (mm) KL/r
ID ID Description (cm2) (N/mm2) (N/mm2)
(m)
99.773
1 1 40-38.3 PIP76X6.0 y 1.254 1.9723 24.7941 13.1947 355 510
7
1 2 38.3-36.65 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
1 3 36.65-35 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
99.773
2 1 35-33.3 PIP76X6.0 y 1.254 1.9723 24.7941 13.1947 355 510
7
2 2 33.3-31.65 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
2 3 31.65-30 PIP76X6.0 y 1.271 1.9294 24.7941 98.908 13.1947 355 510
101.31
3 1 30-28.3 PIP76X6.0 y 1.226 2.0486 24.7941 13.1947 355 510
21
102.09
3 2 28.3-26.65 PIP76X6.0 y 1.213 2.0875 24.7941 13.1947 355 510
74
103.82
3 3 26.65-25 PIP76X6.0 y 1.184 2.1734 24.7941 13.1947 355 510
97
106.45
4 1 25-23.3 PIP76X6.0 y 1.146 2.3038 24.7941 13.1947 355 510
9
107.64
4 2 23.3-21.65 PIP76X6.0 y 1.13 2.3624 24.7941 13.1947 355 510
05
109.64
4 3 21.65-20 PIP76X6.0 y 1.104 2.4616 24.7941 13.1947 355 510
01
112.73
5 1 20-17.5 PIP89X6.0 y 1.069 3.0975 29.3678 15.6451 355 510
71
117.15
6 1 17.5-15 PIP89X6.0 y 1.025 3.3572 29.3678 15.6451 355 510
73
117.15
7 1 15-12.5 PIP89X6.0 y 1.025 3.3572 29.3678 15.6451 355 510
73
122.53
8 1 12.5-10 PIP89X6.0 y 0.987 3.6451 29.3678 15.6451 355 510
29
122.53
9 1 10-7.5 PIP89X6.0 y 0.987 3.6451 29.3678 15.6451 355 510
29
129.02
10 1 7.5-5 PIP89X6.0 y 0.958 3.9551 29.3678 15.6451 355 510
57
129.02
11 1 5-2.5 PIP89X6.0 y 0.958 3.9551 29.3678 15.6451 355 510
57
135.88
12 1 2.5-0 PIP89X6.0 y 0.932 4.2825 29.3678 15.6451 355 510
11

TOPHORIZONTAL SUMMARY

5 20-17.5 EA75X75X6 12.9114 56.1982 12.9114 207.97 22.97
TOPHORIZONTAL SEGMENT SUMMARY

5 1 20-17.5 EA75X75X6 12.9114 56.1982 12.9114 207.97 22.97
TOPHORIZONTAL BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500 12.911
5 20-17.5 EA75X75X6 30 12.9114 87.9593 84.8219 71.1083 18.16
6 4
TOPHORIZONTAL BOLT SEGMENT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500 12.911
5 1 20-17.5 EA75X75X6 30 12.9114 87.9593 84.8219 71.1083 18.16
6 4
TOPHORIZONTAL DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
5 20-17.5 EA75X75X6 y 1 3.65 23.2943 156.6907 8.64 355 510
TOPHORIZONTAL DETAIL SEGMENT
Segment
(m)
156.69
5 1 20-17.5 EA75X75X6 y 1 3.65 23.2943 8.64 355 510
07
HORIZONTAL SUMMARY

1 40-35 EA63X63X6 19.4667 94.4502 19.7038 117.6424 20.61
2 35-30 EA63X63X6 35.2975 94.4502 35.8665 117.6424 37.37
3 30-25 EA63X63X6 27.0558 84.4414 29.2069 117.6424 32.04
4 25-20 EA75X75X6 30.4022 100.8557 30.6878 207.97 30.14
6 17.5-15 EA75X75X6 12.933 104.6765 12.933 207.97 12.36
10 7.5-5 EA75X75X6 17.3659 91.7732 17.3659 207.97 18.92
12 2.5-0 EA125X125X10 19.3728 268.2293 19.3728 622.0167 7.22
HORIZONTAL SEGMENT SUMMARY

1 1 40-38.3 EA63X63X6 3.0163 94.4502 2.9584 117.6424 3.19
1 2 38.3-36.65 EA63X63X6 19.4667 94.4502 19.7038 117.6424 20.61
1 3 36.65-35 EA63X63X6 19.1614 94.4502 19.349 117.6424 20.29
2 1 35-33.3 EA63X63X6 25.1688 94.4502 25.3946 117.6424 26.65
2 2 33.3-31.65 EA63X63X6 28.9309 94.4502 29.1223 117.6424 30.63
2 3 31.65-30 EA63X63X6 35.2975 94.4502 35.8665 117.6424 37.37

HORIZONTAL SEGMENT SUMMARY Cont...

3 1 30-28.3 EA63X63X6 29.8401 94.4502 29.2069 117.6424 31.59
3 2 28.3-26.65 EA63X63X6 26.4941 89.3626 26.487 117.6424 29.65
3 3 26.65-25 EA63X63X6 27.0558 84.4414 27.21 117.6424 32.04
4 1 25-23.3 EA75X75X6 27.356 117.6525 27.5366 207.97 23.25
4 2 23.3-21.65 EA75X75X6 28.3977 109.0977 28.5912 207.97 26.03
4 3 21.65-20 EA75X75X6 30.4022 100.8557 30.6878 207.97 30.14
6 1 17.5-15 EA75X75X6 12.933 104.6765 12.933 207.97 12.36
10 1 7.5-5 EA75X75X6 17.3659 91.7732 17.3659 207.97 18.92
EA125X125X1
12 1 2.5-0 19.3728 268.2293 19.3728 622.0167 7.22
0
HORIZONTAL BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499 19.648
1 40-35 EA63X63X6 30 19.6614 87.9593 50.1555 50.1941 39.2
8 7
31.499 35.297
2 35-30 EA63X63X6 30 35.8665 87.9593 50.1555 50.1941 71.51
8 5
31.499 29.840
3 30-25 EA63X63X6 30 29.2069 87.9593 50.1555 50.1941 58.23
8 1
37.500 30.402
4 25-20 EA75X75X6 30 30.6878 87.9593 84.8219 71.1083 43.16
6 2
37.500
6 17.5-15 EA75X75X6 30 12.933 12.933 87.9593 84.8219 71.1083 18.19
6
37.500 17.365
10 7.5-5 EA75X75X6 30 17.3659 87.9593 84.8219 71.1083 24.42
6 9
62.500 19.372
12 2.5-0 EA125X125X10 30 19.3728 175.9185 321.5084 331.0614 11.01
5 8
HORIZONTAL BOLT SEGMENT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 1 40-38.3 EA63X63X6 30 3.0163 2.9584 87.9593 50.1555 50.1941 5.9
8
31.499 19.648
1 2 38.3-36.65 EA63X63X6 30 19.6614 87.9593 50.1555 50.1941 39.2
8 7
31.499 19.148
1 3 36.65-35 EA63X63X6 30 19.349 87.9593 50.1555 50.1941 38.58
8 2
31.499 25.168
2 1 35-33.3 EA63X63X6 30 25.3408 87.9593 50.1555 50.1941 50.52
8 8
31.499 28.930
2 2 33.3-31.65 EA63X63X6 30 29.1223 87.9593 50.1555 50.1941 58.06
8 9
31.499 35.297
2 3 31.65-30 EA63X63X6 30 35.8665 87.9593 50.1555 50.1941 71.51
8 5
31.499 29.840
3 1 30-28.3 EA63X63X6 30 29.2069 87.9593 50.1555 50.1941 58.23
8 1
31.499 26.494
3 2 28.3-26.65 EA63X63X6 30 26.487 87.9593 50.1555 50.1941 52.81
8 1
31.499 27.055
3 3 26.65-25 EA63X63X6 30 27.21 87.9593 50.1555 50.1941 54.25
8 8
37.500
4 1 25-23.3 EA75X75X6 30 27.356 27.5021 87.9593 84.8219 71.1083 38.68
6
37.500 28.391
4 2 23.3-21.65 EA75X75X6 30 28.5912 87.9593 84.8219 71.1083 40.21
6 6

HORIZONTAL BOLT SEGMENT SUMMARY Cont...
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500 30.402
4 3 21.65-20 EA75X75X6 30 30.6878 87.9593 84.8219 71.1083 43.16
6 2
37.500
6 1 17.5-15 EA75X75X6 30 12.933 12.933 87.9593 84.8219 71.1083 18.19
6
37.500 17.365
10 1 7.5-5 EA75X75X6 30 17.3659 87.9593 84.8219 71.1083 24.42
6 9
62.500 19.372
12 1 2.5-0 EA125X125X10 30 19.3728 175.9185 321.5084 331.0614 11.01
5 8
HORIZONTAL DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
1 40-35 EA63X63X6 y 1.244 1 12.3995 100.3243 7.2 235 360
2 35-30 EA63X63X6 z 1.244 1 12.3995 100.3243 7.2 235 360
3 30-25 EA63X63X6 z 1.083 1.2764 12.3995 111.4689 7.2 235 360
4 25-20 EA75X75X6 z 1.027 1.6889 14.8239 116.9646 8.64 355 510
6 17.5-15 EA75X75X6 z 1.047 1.625 14.8239 114.8101 8.64 355 510
10 7.5-5 EA75X75X6 y 1 2.8563 23.2943 122.6159 8.64 355 510
12 2.5-0 EA125X125X10 y 1.004 2.9419 24.7065 119.5365 24 355 510
HORIZONTAL DETAIL SEGMENT

Segment
(m)
100.32
1 1 40-38.3 EA63X63X6 y 1.244 1 12.3995 7.2 235 360
43
100.32
1 2 38.3-36.65 EA63X63X6 y 1.244 1 12.3995 7.2 235 360
43
100.32
1 3 36.65-35 EA63X63X6 z 1.244 1 12.3995 7.2 235 360
43
100.32
2 1 35-33.3 EA63X63X6 z 1.244 1 12.3995 7.2 235 360
43
100.32
2 2 33.3-31.65 EA63X63X6 z 1.244 1 12.3995 7.2 235 360
43
100.32
2 3 31.65-30 EA63X63X6 z 1.244 1 12.3995 7.2 235 360
43
100.32
3 1 30-28.3 EA63X63X6 y 1.244 1 12.3995 7.2 235 360
43
105.97
3 2 28.3-26.65 EA63X63X6 z 1.152 1.1402 12.3995 7.2 235 360
97
111.46
3 3 26.65-25 EA63X63X6 z 1.083 1.2764 12.3995 7.2 235 360
89
107.64
4 1 25-23.3 EA75X75X6 z 1.13 1.4125 14.8239 8.64 355 510
27
112.37
4 2 23.3-21.65 EA75X75X6 z 1.073 1.5528 14.8239 8.64 355 510
32
116.96
4 3 21.65-20 EA75X75X6 z 1.027 1.6889 14.8239 8.64 355 510
46
114.81
6 1 17.5-15 EA75X75X6 z 1.047 1.625 14.8239 8.64 355 510
01
122.61
10 1 7.5-5 EA75X75X6 y 1 2.8563 23.2943 8.64 355 510
59
119.53
12 1 2.5-0 EA125X125X10 y 1.004 2.9419 24.7065 24 355 510
65

INNERBRACING SUMMARY

5 20-17.5 XAEs56X56X5 0.1462 32.0229 0 0 0.46
10 7.5-5 EA63X63X6 0.1211 54.5206 0.1349 122.5024 0.22
INNERBRACING SEGMENT SUMMARY

5 1 20-17.5 XAEs56X56X5 0.1462 32.0229 0 0 0.46
10 1 7.5-5 EA63X63X6 0.1211 54.5206 0.1349 122.5024 0.22
INNERBRACING BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
5 20-17.5 XAEs56X56X5 30 0.1462 0 87.9593 37.0714 41.8284 0.17
7
31.499
10 7.5-5 EA63X63X6 24 0.1211 0.1349 56.3051 49.5075 39.8261 0.34
8
INNERBRACING BOLT SEGMENT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
5 1 20-17.5 XAEs56X56X5 30 0.1462 0 87.9593 37.0714 41.8284 0.17
7
31.499
10 1 7.5-5 EA63X63X6 24 0.1211 0.1349 56.3051 49.5075 39.8261 0.34
8
INNERBRACING DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
5 20-17.5 XAEs56X56X5 z 1 1.825 11.0392 165.3207 5.35 235 360
10 7.5-5 EA63X63X6 y 1 2.8562 19.4325 146.9828 7.2 235 360
INNERBRACING DETAIL SEGMENT
Segment
(m)
165.32
5 1 20-17.5 XAEs56X56X5 z 1 1.825 11.0392 5.35 235 360
07
146.98
10 1 7.5-5 EA63X63X6 y 1 2.8562 19.4325 7.2 235 360
28
SUBINNERBRACING1 SUMMARY

10 7.5-5 XAEs56X56X5 0.0799 51.1359 0 0 0.16
SUBINNERBRACING1 SEGMENT SUMMARY

10 1 7.5-5 XAEs56X56X5 0.0799 51.1359 0 0 0.16

SUBINNERBRACING1 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
10 7.5-5 XAEs56X56X5 24 0.0799 0 56.3051 36.5314 33.1884 0.14
7
SUBINNERBRACING1 BOLT SEGMENT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
27.999
10 1 7.5-5 XAEs56X56X5 24 0.0799 0 56.3051 36.5314 33.1884 0.14
7
SUBINNERBRACING1 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
10 7.5-5 XAEs56X56X5 z 1 1.4281 11.0392 129.3691 5.35 235 360
SUBINNERBRACING1 DETAIL SEGMENT
Segment
(m)
129.36
10 1 7.5-5 XAEs56X56X5 z 1 1.4281 11.0392 5.35 235 360
91
PB6 SUMMARY

12 2.5-0 100X100X8EA 0.2717 192.7017 0.2081 318.8868 0.14
PB6 SEGMENT SUMMARY

12 1 2.5-0 100X100X8EA 0.2717 192.7017 0.2081 318.8868 0.14
PB6 BOLT SUMMARY

Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
49.999
12 2.5-0 100X100X8EA 30 0.2717 0 87.9593 124.4169 77.9403 0.31
9
PB6 BOLT SEGMENT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
49.999
12 1 2.5-0 100X100X8EA 30 0.2717 0 87.9593 124.4169 77.9403 0.31
9
PB6 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
12 2.5-0 100X100X8EA y 1.134 2.9419 31.0875 107.316 14.9916 275 430
PB6 DETAIL SEGMENT
Segment
(m)
107.31
12 1 2.5-0 100X100X8EA y 1.134 2.9419 31.0875 14.9916 275 430
6
PB7 SUMMARY

12 2.5-0 EA63X63X6 0.2568 101.0574 0 0 0.25
PB7 SEGMENT SUMMARY

12 1 2.5-0 EA63X63X6 0.2568 101.0574 0 0 0.25
PB7 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
12 2.5-0 EA63X63X6 24 0.2568 0 56.3051 49.5075 39.8261 0.46
8
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
12 1 2.5-0 EA63X63X6 24 0.2568 0 56.3051 49.5075 39.8261 0.46
8
PB7 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
12 2.5-0 EA63X63X6 z 1.41 0.8172 12.3995 92.9525 7.2 235 360
PB7 DETAIL SEGMENT

Segment
(m)
92.952
12 1 2.5-0 EA63X63X6 z 1.41 0.8172 12.3995 7.2 235 360
5
PB8 SUMMARY

12 2.5-0 EA75X75X6 0.3519 97.4252 0.1134 151.6624 0.36
PB8 SEGMENT SUMMARY

12 1 2.5-0 EA75X75X6 0.3519 97.4252 0.1134 151.6624 0.36

PB8 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500
12 2.5-0 EA75X75X6 24 0.3519 0 56.3051 59.2263 39.8261 0.63
6
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
37.500
12 1 2.5-0 EA75X75X6 24 0.3519 0 56.3051 59.2263 39.8261 0.63
6
PB8 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
12 2.5-0 EA75X75X6 z 1.044 1.6343 14.8239 115.123 8.64 235 360
PB8 DETAIL SEGMENT
Segment
(m)
115.12
12 1 2.5-0 EA75X75X6 z 1.044 1.6343 14.8239 8.64 235 360
3
PB2 SUMMARY

1 40-35 EA63X63X6 0.0892 82.3912 0.0795 122.5024 0.11
1 40-35 EA50X50X5 0.1482 63.9751 0.1468 76.7728 0.23
2 35-30 EA50X50X5 0.14 63.9751 0.1395 76.7728 0.22
3 30-25 EA63X63X6 0.1079 82.3912 0.0667 122.5024 0.13
4 25-20 EA63X63X6 0.1055 51.0509 0.0495 122.5024 0.21
6 17.5-15 XAEs56X56X5 0.2653 40.3905 0.1984 88.9228 0.66
8 12.5-10 EA63X63X6 0.2132 47.3813 0.1531 122.5024 0.45
PB2 SEGMENT SUMMARY

1 1 40-38.3 EA63X63X6 0.0892 82.3912 0.0795 122.5024 0.11
1 2 38.3-36.65 EA50X50X5 0.1482 63.9751 0.1468 76.7728 0.23
2 1 35-33.3 EA50X50X5 0.14 63.9751 0.1395 76.7728 0.22
3 1 30-28.3 EA63X63X6 0.1079 82.3912 0.0667 122.5024 0.13
4 1 25-23.3 EA63X63X6 0.1055 51.0509 0.0495 122.5024 0.21
6 1 17.5-15 XAEs56X56X5 0.2653 40.3905 0.1984 88.9228 0.66
8 1 12.5-10 EA63X63X6 0.2132 47.3813 0.1531 122.5024 0.45
PB2 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
24.999
1 40-35 EA50X50X5 24 0.1482 0.1468 56.3051 32.4811 33.1884 0.45
9

PB2 BOLT SUMMARY Cont...
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
24.999
2 35-30 EA50X50X5 24 0.14 0.1395 56.3051 32.4811 33.1884 0.43
9
31.499
3 30-25 EA63X63X6 24 0.1079 0.0667 56.3051 49.5075 39.8261 0.19
8
31.499
4 25-20 EA63X63X6 24 0.1055 0.0495 56.3051 49.5075 39.8261 0.19
8
27.999
6 17.5-15 XAEs56X56X5 24 0.2652 0.1984 56.3051 36.5314 33.1884 0.6
7
31.499
8 12.5-10 EA63X63X6 18 0.2132 0.1531 15.255 48.8595 29.4581 1.4
8
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 1 40-38.3 EA63X63X6 24 0.0892 0.0795 56.3051 49.5075 39.8261 0.2
8
24.999
1 2 38.3-36.65 EA50X50X5 24 0.1482 0.1468 56.3051 32.4811 33.1884 0.45
9
24.999
2 1 35-33.3 EA50X50X5 24 0.14 0.1395 56.3051 32.4811 33.1884 0.43
9
31.499
3 1 30-28.3 EA63X63X6 24 0.1079 0.0667 56.3051 49.5075 39.8261 0.19
8
31.499
4 1 25-23.3 EA63X63X6 24 0.1055 0.0495 56.3051 49.5075 39.8261 0.19
8
27.999
6 1 17.5-15 XAEs56X56X5 24 0.2652 0.1984 56.3051 36.5314 33.1884 0.6
7
31.499
8 1 12.5-10 EA63X63X6 18 0.2132 0.1531 15.255 48.8595 29.4581 1.4
8
PB2 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
1 40-35 EA50X50X5 y 1.3 1.1548 15.3899 97.5168 4.75 235 360
2 35-30 EA50X50X5 y 1.3 1.1548 15.3899 97.5168 4.75 235 360
3 30-25 EA63X63X6 z 1.058 1.3334 12.3995 113.7684 7.2 235 360
4 25-20 EA63X63X6 z 1 1.8834 12.3995 151.8956 7.2 235 360
6 17.5-15 XAEs56X56X5 z 1 1.625 11.0392 147.2033 5.35 235 360
8 12.5-10 EA63X63X6 z 1 1.955 12.3995 157.6679 7.2 235 360
PB2 DETAIL SEGMENT
Segment
(m)
113.76
1 1 40-38.3 EA63X63X6 z 1.058 1.3334 12.3995 7.2 235 360
84
97.516
1 2 38.3-36.65 EA50X50X5 y 1.3 1.1548 15.3899 4.75 235 360
8
97.516
2 1 35-33.3 EA50X50X5 y 1.3 1.1548 15.3899 4.75 235 360
8
113.76
3 1 30-28.3 EA63X63X6 z 1.058 1.3334 12.3995 7.2 235 360
84
151.89
4 1 25-23.3 EA63X63X6 z 1 1.8834 12.3995 7.2 235 360
56

PB2 DETAIL SEGMENT Cont...
Segment
(m)
147.20
6 1 17.5-15 XAEs56X56X5 z 1 1.625 11.0392 5.35 235 360
33
157.66
8 1 12.5-10 EA63X63X6 z 1 1.955 12.3995 7.2 235 360
79
PB3 SUMMARY

1 40-35 EA63X63X6 0.0375 106.4283 0.0366 122.5024 0.04
2 35-30 EA63X63X5 0.0353 89.5168 0.0347 103.0978 0.04
6 17.5-15 XAEs56X56X5 0.2497 25.8499 0.2954 88.9228 0.97
8 12.5-10 EA63X63X6 0.2929 30.3241 0.1577 127.3624 0.97
PB3 SEGMENT SUMMARY

1 2 38.3-36.65 EA63X63X6 0.0375 106.4283 0.0366 122.5024 0.04
2 1 35-33.3 EA63X63X5 0.0353 89.5168 0.0347 103.0978 0.04
6 1 17.5-15 XAEs56X56X5 0.2497 25.8499 0.2954 88.9228 0.97
8 1 12.5-10 EA63X63X6 0.2929 30.3241 0.1577 127.3624 0.97
PB3 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 40-35 EA63X63X6 24 0.0375 0.0366 56.3051 49.5075 39.8261 0.09
8
31.499
2 35-30 EA63X63X5 24 0.0353 0.0347 56.3051 41.2563 33.1884 0.1
8
27.999
6 17.5-15 XAEs56X56X5 24 0.2497 0.2954 56.3051 36.5314 33.1884 0.89
7
31.499
8 12.5-10 EA63X63X6 18 0.2929 0.1577 15.255 48.8595 29.4581 1.92
8
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
1 2 38.3-36.65 EA63X63X6 24 0.0375 0.0366 56.3051 49.5075 39.8261 0.09
8
31.499
2 1 35-33.3 EA63X63X5 24 0.0353 0.0347 56.3051 41.2563 33.1884 0.1
8
27.999
6 1 17.5-15 XAEs56X56X5 24 0.2497 0.2954 56.3051 36.5314 33.1884 0.89
7
31.499
8 1 12.5-10 EA63X63X6 18 0.2929 0.1577 15.255 48.8595 29.4581 1.92
8
PB3 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
1 40-35 EA63X63X6 z 1.616 0.6667 12.3995 86.885 7.2 235 360
2 35-30 EA63X63X5 z 1.621 0.6667 12.4544 86.7663 6.05 235 360
6 17.5-15 XAEs56X56X5 z 1 2.0312 11.0392 184.0042 5.35 235 360

PB3 DETAIL Cont...
Tower Fy Fu
Section Member Area
(m) m2) m2)
8 12.5-10 EA63X63X6 z 1 2.4438 12.3995 197.0848 7.2 235 360
PB3 DETAIL SEGMENT
Segment
(m)
1 2 38.3-36.65 EA63X63X6 z 1.616 0.6667 12.3995 86.885 7.2 235 360
86.766
2 1 35-33.3 EA63X63X5 z 1.621 0.6667 12.4544 6.05 235 360
3
184.00
6 1 17.5-15 XAEs56X56X5 z 1 2.0312 11.0392 5.35 235 360
42
197.08
8 1 12.5-10 EA63X63X6 z 1 2.4438 12.3995 7.2 235 360
48
PB4 SUMMARY

6 17.5-15 EA63X63X6 0.1129 79.2296 0 0 0.14
8 12.5-10 EA63X63X6 0.009 61.7127 0.0727 122.5024 0.06
PB4 SEGMENT SUMMARY

6 1 17.5-15 EA63X63X6 0.1129 79.2296 0 0 0.14
8 1 12.5-10 EA63X63X6 0.009 61.7127 0.0727 122.5024 0.06
PB4 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
6 17.5-15 EA63X63X6 24 0.1129 0 56.3051 49.5075 39.8261 0.2
8
31.499
8 12.5-10 EA63X63X6 18 0.009 0.0727 56.3051 43.6755 27.3845 0.27
8
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
6 1 17.5-15 EA63X63X6 24 0.1129 0 56.3051 49.5075 39.8261 0.2
8
31.499
8 1 12.5-10 EA63X63X6 18 0.009 0.0727 56.3051 43.6755 27.3845 0.27
8
PB4 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
6 17.5-15 EA63X63X6 z 1.023 1.4219 12.3995 117.3361 7.2 235 360
8 12.5-10 EA63X63X6 z 1 1.7106 12.3995 137.9594 7.2 235 360

PB4 DETAIL SEGMENT
Segment
(m)
117.33
6 1 17.5-15 EA63X63X6 z 1.023 1.4219 12.3995 7.2 235 360
61
137.95
8 1 12.5-10 EA63X63X6 z 1 1.7106 12.3995 7.2 235 360
94
PB1 SUMMARY

8 12.5-10 EA63X63X6 7.1562 47.3813 7.8374 122.5024 15.1
PB1 SEGMENT SUMMARY

8 1 12.5-10 EA63X63X6 7.1562 47.3813 7.8374 122.5024 15.1
PB1 BOLT SUMMARY
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
8 12.5-10 EA63X63X6 24 7.3158 7.8184 56.3051 49.5075 39.8261 19.63
8
Member
(m) (mm) (mm) ) (kN) (kN) (kN)
(kN)
31.499
8 1 12.5-10 EA63X63X6 24 7.3158 7.8184 56.3051 49.5075 39.8261 19.63
8
PB1 DETAIL
Tower Fy Fu
Section Member Area
(m) m2) m2)
8 12.5-10 EA63X63X6 z 1 1.955 12.3995 157.6679 7.2 235 360
PB1 DETAIL SEGMENT
Segment
(m)
157.66
8 1 12.5-10 EA63X63X6 z 1 1.955 12.3995 7.2 235 360
79
Tower Summary Information
Section Tower Member Controlling Capacity Ratio

Member Type Pu (kN) ϕPn (kN) Result
ID Elevation (m) Description Component (%)
1 40-35 PIP114X6.0 LEG Compression 61.8193 567.0303 10.9 Pass
4 25-20 PIP194X10.0 LEG BOLT 606.8145 1251.225 48.5 Pass
5 20-17.5 PIP203X12.0 LEG Compression 748.4875 2078.4434 36.01 Pass
5 20-17.5 PIP203X12.0 LEG BOLT 701.0843 1251.225 56.03 Pass
6 17.5-15 PIP203X12.0 LEG Compression 749.7377 2078.4434 36.07 Pass

Tower Summary Information Cont...

ANCHOR
12 2.5-0 UPT:M48_8.8_N LEG 1056.8 7211.04 17.86 Pass
ROD**
1 40-35 PIP76X6.0 DIAGONAL Compression 37.4153 205.5226 18.2 Pass
1 40-35 PIP76X6.0 DIAGONAL BOLT 37.4153 175.9185 21.27 Pass
5 20-17.5 PIP89X6.0 DIAGONAL Compression 49.7479 196.5573 25.31 Pass
5 20-17.5 PIP89X6.0 DIAGONAL BOLT 49.7479 175.9185 28.28 Pass
6 17.5-15 PIP89X6.0 DIAGONAL Compression 54.211 182.0268 29.78 Pass
6 17.5-15 PIP89X6.0 DIAGONAL BOLT 54.211 175.9185 30.82 Pass
7 15-12.5 PIP89X6.0 DIAGONAL BOLT 48.0865 175.9185 27.33 Pass
12 2.5-0 100X100X8EA PB6 Compression 0.2717 192.7017 0.14 Pass
12 2.5-0 100X100X8EA PB6 BOLT 0 77.9403 0.31 Pass
12 2.5-0 EA63X63X6 PB7 Compression 0.2568 101.0574 0.25 Pass
12 2.5-0 EA63X63X6 PB7 BOLT 0 39.8261 0.46 Pass
12 2.5-0 EA75X75X6 PB8 BOLT 0 39.8261 0.63 Pass
INNERBRACI
5 20-17.5 XAEs56X56X5 Compression 0.1462 32.0229 0.46 Pass
NG
INNERBRACI
10 7.5-5 EA63X63X6 Compression 0.1211 54.5206 0.22 Pass
NG
INNERBRACI
10 7.5-5 EA63X63X6 BOLT 0.1349 39.8261 0.34 Pass
NG
SUBINNERBR
10 7.5-5 XAEs56X56X5 Compression 0.0799 51.1359 0.16 Pass
ACING1
1 40-35 EA63X63X6 PB2 Compression 0.0892 82.3912 0.11 Pass
1 40-35 EA63X63X6 PB2 BOLT 0.0795 39.8261 0.2 Pass
1 40-35 EA50X50X5 PB2 BOLT 0.1468 32.4811 0.45 Pass
2 35-30 EA50X50X5 PB2 BOLT 0.1395 32.4811 0.43 Pass
3 30-25 EA63X63X6 PB2 BOLT 0.0667 39.8261 0.19 Pass
6 17.5-15 XAEs56X56X5 PB2 Compression 0.2653 40.3905 0.66 Pass
8 12.5-10 EA63X63X6 PB2 BOLT 0.2132 15.255 1.4 Pass
1 40-35 EA63X63X6 PB3 BOLT 0.0366 39.8261 0.09 Pass
2 35-30 EA63X63X5 PB3 BOLT 0.0347 33.1884 0.1 Pass

6 17.5-15 XAEs56X56X5 PB3 Compression 0.2497 25.8499 0.97 Pass
8 12.5-10 EA63X63X6 PB3 BOLT 0.2929 15.255 1.92 Pass
6 17.5-15 EA63X63X6 PB4 BOLT 0 39.8261 0.2 Pass
8 12.5-10 EA63X63X6 PB4 Tension 0.0727 122.5024 0.06 Pass
8 12.5-10 EA63X63X6 PB4 BOLT 0.0727 27.3845 0.27 Pass
1 40-35 EA63X63X6 HORIZONTAL Compression 19.4667 94.4502 20.61 Pass
1 40-35 EA63X63X6 HORIZONTAL BOLT 19.6614 50.1555 39.2 Pass
6 17.5-15 EA75X75X6 HORIZONTAL Compression 12.933 104.6765 12.36 Pass
6 17.5-15 EA75X75X6 HORIZONTAL BOLT 12.933 71.1083 18.19 Pass
8 12.5-10 EA63X63X6 PB1 BOLT 7.8184 39.8261 19.63 Pass
TOPHORIZO
5 20-17.5 EA75X75X6 Compression 12.9114 56.1982 22.97 Pass
NTAL
Summary
LEG(5) 56.03 Pass
LEG ANCHOR
17.86 Pass
ROD(12)
DIAGONAL
40.08 Pass
(12)
DIAGONAL
38.64 Pass
BOLT(2)
PB6(12) 0.14 Pass
PB6 BOLT(12) 0.31 Pass
PB7(12) 0.25 Pass
PB8(12) 0.36 Pass
INNERBRACI
0.46 Pass
NG(5)
INNERBRACI
0.34 Pass
NG BOLT(10)
SUBINNERBR
0.16 Pass
ACING1(10)
PB2(6) 0.66 Pass
PB3(6) 0.97 Pass
PB4(6) 0.14 Pass
HORIZONTAL
37.37 Pass
(2)
HORIZONTAL
71.51 Pass
BOLT(2)
PB1(8) 15.1 Pass


TOPHORIZO
22.97 Pass
NTAL(5)
Rating 71.51 Pass
** Anchor Rod controlling component -Axial+Shear
Deflection Profile
Critical Load Combination : C 6 - 1.2D + 1.6Wo-120°

Tilt
Twist

Summary Tower Reaction
Maximum Reaction Load Combination Moment (kNm) Axial (kN) Shear (kN)
Compression C 6 - 1.2D + 1.6Wo-120° 18 1177.74 179.23
Tension C 24 - 0.9D + 1.6Wo-300° 21.78 -1069.96 163.35
Shear C 6 - 1.2D + 1.6Wo-120° 18 1177.74 179.23
Total Overturning Moment

C 6 - 1.2D + 1.6Wo-120° 6795.97 152.22 288.53
(1.2D)

C 18 - 0.9D + 1.6Wo-120° 6793.17 114.17 288.53
(0.9D)

C 30 - 1.0D + 1.0Ws-120° 562.38 126.85 23.93
(1.0D)
Total Compression C 8 - 1.2D + 1.6Wo-180° 6503.9 152.22 275.41
Total Shear C 18 - 0.9D + 1.6Wo-120° 6793.17 114.17 288.53
Tower Reaction Summary

Overturning Overturning
Torque
Node Id Load Combination Vertical (kN) Shear x (kN) Shear z (kN) Moment Moment
(kNm)
(Mx) (kNm) (Mz) (kNm)
152 C 1 - 1.00 SW 41.3490 0.0510 5.7080 −2.4280 −0.0590 0.0080
C 2 - 1.2D + 1.6Wo-
152 1.1614e+3 3.2190 177.4450 18.2440 −9.7790 0.0810
0°
C 3 - 1.2D + 1.6Wo-
152 983.7030 −5.6350 149.9410 14.6480 24.1980 −2.3740
30°
C 4 - 1.2D + 1.6Wo-
152 574.1000 −13.1820 87.4620 7.2860 51.9910 −4.1890
60°
C 5 - 1.2D + 1.6Wo-
152 42.1460 −17.1480 6.0230 −2.6660 65.7310 −5.0030
90°
C 6 - 1.2D + 1.6Wo-
152 −497.8250 −16.7370 −77.2630 −13.4670 62.6870 −4.5960
120°
C 7 - 1.2D + 1.6Wo-
152 −889.1610 −10.8730 −136.7580 −20.3160 39.8430 −2.5800
150°
C 8 - 1.2D + 1.6Wo-
152 −1.0279e+3 −3.2620 −157.7420 −22.6310 10.0570 −0.0680
180°
C 9 - 1.2D + 1.6Wo-
152 −887.8760 5.6290 −136.6050 −20.3450 −23.7070 2.4510
210°
C 10 - 1.2D + 1.6Wo-
152 −475.1750 14.4490 −74.6380 −14.0680 −55.7460 4.2400
240°
C 11 - 1.2D + 1.6Wo-
152 66.9950 17.4210 8.9010 −3.3290 −66.4490 4.8520
270°

Tower Reaction Summary Cont...
Torque
(kNm)
C 12 - 1.2D + 1.6Wo-
152 594.8720 15.9720 89.8700 6.7350 −60.1860 4.2550
300°
C 13 - 1.2D + 1.6Wo-
152 994.7800 11.0100 151.2280 14.3580 −40.2620 2.5750
330°
C 14 - 0.9D + 1.6Wo-
152 1.1490e+3 3.2040 175.7330 18.9730 −9.7610 0.0790
0°
C 15 - 0.9D + 1.6Wo-
152 971.2980 −5.6500 148.2290 15.3770 24.2160 −2.3770
30°
C 16 - 0.9D + 1.6Wo-
152 561.6960 −13.1970 85.7490 8.0140 52.0080 −4.1910
60°
C 17 - 0.9D + 1.6Wo-
152 29.7410 −17.1630 4.3110 −1.9380 65.7480 −5.0060
90°
C 18 - 0.9D + 1.6Wo-
152 −510.2300 −16.7530 −78.9750 −12.7390 62.7050 −4.5980
120°
C 19 - 0.9D + 1.6Wo-
152 −901.5660 −10.8880 −138.4700 −19.5880 39.8600 −2.5820
150°
C 20 - 0.9D + 1.6Wo-
152 −1.0403e+3 −3.2770 −159.4540 −21.9030 10.0740 −0.0710
180°
C 21 - 0.9D + 1.6Wo-
152 −900.2810 5.6140 −138.3170 −19.6160 −23.6890 2.4490
210°
C 22 - 0.9D + 1.6Wo-
152 −487.5800 14.4340 −76.3500 −13.3400 −55.7280 4.2380
240°
C 23 - 0.9D + 1.6Wo-
152 54.5900 17.4050 7.1880 −2.6010 −66.4310 4.8500
270°
C 24 - 0.9D + 1.6Wo-
152 582.4680 15.9560 88.1570 7.4630 −60.1680 4.2530
300°
C 25 - 0.9D + 1.6Wo-
152 982.3750 10.9940 149.5160 15.0870 −40.2450 2.5730
330°
C 26 - 1.0D + 1.0Ws-
152 132.0370 0.2910 19.8310 −0.4370 −0.7980 0.0130
0°
C 27 - 1.0D + 1.0Ws-
152 117.6960 −0.4710 17.5850 −0.7620 2.1090 −0.2030
30°
C 28 - 1.0D + 1.0Ws-
152 84.3040 −1.1100 12.4140 −1.4610 4.4590 −0.3620
60°
C 29 - 1.0D + 1.0Ws-
152 40.7800 −1.4350 5.6450 −2.4090 5.5910 −0.4320
90°

Torque
(kNm)
C 30 - 1.0D + 1.0Ws-
152 −3.3530 −1.3800 −1.2630 −3.4210 5.2730 −0.3930
120°
C 31 - 1.0D + 1.0Ws-
152 −35.3560 −0.8690 −6.2080 −4.0810 3.3000 −0.2180
150°
C 32 - 1.0D + 1.0Ws-
152 −46.7250 −0.2020 −7.9580 −4.3080 0.7120 0.0020
180°
C 33 - 1.0D + 1.0Ws-
152 −35.2580 0.5630 −6.1970 −4.0830 −2.1790 0.2230
210°
C 34 - 1.0D + 1.0Ws-
152 −1.6290 1.2990 −1.0640 −3.4670 −4.8520 0.3800
240°
C 35 - 1.0D + 1.0Ws-
152 42.6710 1.5480 5.8640 −2.4590 −5.7520 0.4340
270°
C 36 - 1.0D + 1.0Ws-
152 85.8830 1.4140 12.5970 −1.5030 −5.1900 0.3810
300°
C 37 - 1.0D + 1.0Ws-
152 118.5390 0.9720 17.6840 −0.7840 −3.4390 0.2320
330°
C 38 - 1.2D + 1.0
152 158.2070 0.1320 22.3570 −2.1420 −0.2810 0.0290
seismic in 0°
C 39 - 1.2D + 1.0
152 143.6590 −0.5480 20.2800 −2.2450 2.5530 −0.1990
seismic in 30°
C 40 - 1.2D + 1.0
152 103.9130 −1.0640 14.6040 −2.5280 4.6840 −0.3700
seismic in 60°
C 41 - 1.2D + 1.0
152 49.6190 −1.2780 6.8500 −2.9130 5.5410 −0.4400
seismic in 90°
C 42 - 1.2D + 1.0
152 −4.6760 −1.1340 −0.9040 −3.2990 4.8950 −0.3900
seismic in 120°
C 43 - 1.2D + 1.0
152 −44.4220 −0.6700 −6.5800 −3.5810 2.9180 −0.2330
seismic in 150°
C 44 - 1.2D + 1.0
152 −58.9700 −0.0100 −8.6580 −3.6840 0.1400 −0.0100
seismic in 180°
C 45 - 1.2D + 1.0
152 −44.4220 0.6700 −6.5800 −3.5810 −2.6940 0.2170
seismic in 210°
C 46 - 1.2D + 1.0
152 −4.6760 1.1860 −0.9040 −3.2980 −4.8250 0.3890
seismic in 240°
C 47 - 1.2D + 1.0
152 49.6190 1.4010 6.8500 −2.9130 −5.6820 0.4590
seismic in 270°
C 48 - 1.2D + 1.0
152 103.9130 1.2560 14.6040 −2.5270 −5.0360 0.4080
seismic in 300°
Torque
(kNm)
seismic in 300°
C 49 - 1.2D + 1.0
152 143.6590 0.7920 20.2800 −2.2450 −3.0590 0.2510
seismic in 330°
C 50 - 0.9D + 1.0
152 145.8030 0.1160 20.6450 −1.4140 −0.2640 0.0270
seismic in 0°
C 51 - 0.9D + 1.0
152 131.2550 −0.5630 18.5670 −1.5170 2.5700 −0.2010
seismic in 30°
C 52 - 0.9D + 1.0
152 91.5080 −1.0790 12.8910 −1.7990 4.7020 −0.3730
seismic in 60°
C 53 - 0.9D + 1.0
152 37.2140 −1.2940 5.1370 −2.1850 5.5590 −0.4430
seismic in 90°
C 54 - 0.9D + 1.0
152 −17.0810 −1.1500 −2.6160 −2.5700 4.9120 −0.3920
seismic in 120°
C 55 - 0.9D + 1.0
152 −56.8270 −0.6850 −8.2920 −2.8530 2.9360 −0.2350
seismic in 150°
C 56 - 0.9D + 1.0
152 −71.3750 −0.0250 −10.3700 −2.9560 0.1580 −0.0130
seismic in 180°
C 57 - 0.9D + 1.0
152 −56.8270 0.6540 −8.2920 −2.8520 −2.6760 0.2150
seismic in 210°
C 58 - 0.9D + 1.0
152 −17.0800 1.1710 −2.6160 −2.5700 −4.8070 0.3860
seismic in 240°
C 59 - 0.9D + 1.0
152 37.2140 1.3850 5.1370 −2.1850 −5.6650 0.4570
seismic in 270°
C 60 - 0.9D + 1.0
152 91.5080 1.2410 12.8910 −1.7990 −5.0180 0.4060
seismic in 300°
C 61 - 0.9D + 1.0
152 131.2550 0.7770 18.5670 −1.5170 −3.0410 0.2490
seismic in 330°
151 C 1 - 1.00 SW 43.8420 −5.0250 −2.8980 1.3050 −2.2990 −0.0020
C 2 - 1.2D + 1.6Wo-
151 −522.0550 59.5630 57.8510 69.7470 24.9680 5.3620
0°
C 3 - 1.2D + 1.6Wo-
151 71.9790 −19.8960 15.5530 74.6000 39.1660 5.7690
30°
C 4 - 1.2D + 1.6Wo-
151 619.4440 −90.3440 −29.1420 59.0050 41.3490 5.0410
60°
C 5 - 1.2D + 1.6Wo-
151 1.0152e+3 −138.9860 −66.4630 30.0900 33.4550 3.1160
90°

Torque
(kNm)
C 6 - 1.2D + 1.6Wo-
151 1.1777e+3 −155.6380 −88.8760 −6.4750 16.7990 0.1900
120°
C 7 - 1.2D + 1.6Wo-
151 1.0069e+3 −126.6650 −85.5520 −40.8000 −7.4550 −2.8620
150°
C 8 - 1.2D + 1.6Wo-
151 603.0700 −68.6270 −62.3610 −64.6890 −29.9880 −4.9720
180°
C 9 - 1.2D + 1.6Wo-
151 51.9310 5.7930 −23.5900 −71.0110 −44.7870 −5.7440
210°
C 10 - 1.2D + 1.6Wo-
151 −539.9420 81.9600 23.8590 −56.5440 −47.8600 −5.3750
240°
C 11 - 1.2D + 1.6Wo-
151 −922.2910 128.1180 60.3730 −26.6430 −38.4660 −3.1050
270°
C 12 - 1.2D + 1.6Wo-
151 −1.0568e+3 140.4060 80.0170 8.6330 −20.8510 −0.1940
300°
C 13 - 1.2D + 1.6Wo-
151 −921.9090 116.8720 79.7080 43.2730 1.9270 2.8390
330°
C 14 - 0.9D + 1.6Wo-
151 −535.2080 61.0700 58.7200 69.3550 25.6570 5.3630
0°
C 15 - 0.9D + 1.6Wo-
151 58.8260 −18.3890 16.4220 74.2090 39.8560 5.7690
30°
C 16 - 0.9D + 1.6Wo-
151 606.2910 −88.8370 −28.2730 58.6130 42.0390 5.0420
60°
C 17 - 0.9D + 1.6Wo-
151 1.0020e+3 −137.4790 −65.5940 29.6980 34.1450 3.1160
90°
C 18 - 0.9D + 1.6Wo-
151 1.1646e+3 −154.1300 −88.0070 −6.8660 17.4890 0.1910
120°
C 19 - 0.9D + 1.6Wo-
151 993.7720 −125.1580 −84.6820 −41.1920 −6.7650 −2.8620
150°
C 20 - 0.9D + 1.6Wo-
151 589.9170 −67.1200 −61.4920 −65.0810 −29.2980 −4.9710
180°
C 21 - 0.9D + 1.6Wo-
151 38.7790 7.3010 −22.7210 −71.4020 −44.0970 −5.7430
210°
C 22 - 0.9D + 1.6Wo-
151 −553.0950 83.4670 24.7280 −56.9350 −47.1700 −5.3750
240°
C 23 - 0.9D + 1.6Wo-
151 −935.4440 129.6260 61.2420 −27.0340 −37.7760 −3.1040
270°
C 24 - 0.9D + 1.6Wo-
151 −1.0700e+3 141.9130 80.8870 8.2410 −20.1620 −0.1940
300°
Torque
(kNm)
300°
C 25 - 0.9D + 1.6Wo-
151 −935.0620 118.3800 80.5770 42.8810 2.6160 2.8400
330°
C 26 - 1.0D + 1.0Ws-
151 −2.9290 0.3850 2.1860 7.0710 −0.0750 0.4570
0°
C 27 - 1.0D + 1.0Ws-
151 45.3160 −6.1680 −1.2970 7.4190 1.2130 0.4960
30°
C 28 - 1.0D + 1.0Ws-
151 90.0170 −12.0110 −5.0040 6.0630 1.5010 0.4320
60°
C 29 - 1.0D + 1.0Ws-
151 122.3600 −16.0420 −8.1090 3.5890 0.9030 0.2650
90°
C 30 - 1.0D + 1.0Ws-
151 135.5450 −17.3980 −9.9680 0.5030 −0.4810 0.0130
120°
C 31 - 1.0D + 1.0Ws-
151 121.7300 −15.0170 −9.7140 −2.3620 −2.5320 −0.2490
150°
C 32 - 1.0D + 1.0Ws-
151 88.7720 −10.2060 −7.7970 −4.3140 −4.4850 −0.4300
180°
C 33 - 1.0D + 1.0Ws-
151 43.7910 −4.0370 −4.5810 −4.7740 −5.8180 −0.4970
210°
C 34 - 1.0D + 1.0Ws-
151 −4.2900 2.2420 −0.6650 −3.5040 −6.1740 −0.4610
240°
C 35 - 1.0D + 1.0Ws-
151 −35.6120 6.0840 2.3790 −0.9550 −5.4620 −0.2670
270°
C 36 - 1.0D + 1.0Ws-
151 −46.6640 7.1070 4.0260 2.0330 −4.0050 −0.0160
300°
C 37 - 1.0D + 1.0Ws-
151 −35.5830 5.1400 4.0030 4.9220 −2.0670 0.2440
330°
C 38 - 1.2D + 1.0
151 −1.6840 0.0380 1.5100 6.3160 −0.4590 0.4240
seismic in 0°
C 39 - 1.2D + 1.0
151 52.6110 −6.7800 −2.1780 6.8730 0.3050 0.4930
seismic in 30°
C 40 - 1.2D + 1.0
151 106.9050 −13.3970 −6.2140 6.0080 0.2490 0.4300
seismic in 60°
C 41 - 1.2D + 1.0
151 146.6510 −18.0400 −9.5170 3.9530 −0.6130 0.2510
seismic in 90°
C 42 - 1.2D + 1.0
151 161.2000 −19.4650 −11.2020 1.2580 −2.0500 0.0040
seismic in 120°

Torque
(kNm)
C 43 - 1.2D + 1.0
151 146.6510 −17.2900 −10.8170 −1.3540 −3.6770 −0.2450
seismic in 150°
C 44 - 1.2D + 1.0
151 106.9050 −12.0970 −8.4660 −3.1830 −5.0580 −0.4280
seismic in 180°
C 45 - 1.2D + 1.0
151 52.6110 −5.2790 −4.7780 −3.7400 −5.8220 −0.4980
seismic in 210°
C 46 - 1.2D + 1.0
151 −1.6840 1.3380 −0.7420 −2.8760 −5.7660 −0.4340
seismic in 240°
C 47 - 1.2D + 1.0
151 −41.4300 5.9810 2.5610 −0.8210 −4.9040 −0.2550
seismic in 270°
C 48 - 1.2D + 1.0
151 −55.9780 7.4060 4.2460 1.8740 −3.4670 −0.0080
seismic in 300°
C 49 - 1.2D + 1.0
151 −41.4300 5.2300 3.8610 4.4860 −1.8400 0.2400
seismic in 330°
C 50 - 0.9D + 1.0
151 −14.8360 1.5450 2.3790 5.9240 0.2300 0.4240
seismic in 0°
C 51 - 0.9D + 1.0
151 39.4580 −5.2730 −1.3080 6.4810 0.9950 0.4940
seismic in 30°
C 52 - 0.9D + 1.0
151 93.7520 −11.8900 −5.3450 5.6160 0.9380 0.4310
seismic in 60°
C 53 - 0.9D + 1.0
151 133.4990 −16.5330 −8.6480 3.5610 0.0760 0.2510
seismic in 90°
C 54 - 0.9D + 1.0
151 148.0470 −17.9570 −10.3320 0.8670 −1.3610 0.0050
seismic in 120°
C 55 - 0.9D + 1.0
151 133.4990 −15.7820 −9.9480 −1.7450 −2.9880 −0.2440
seismic in 150°
C 56 - 0.9D + 1.0
151 93.7520 −10.5900 −7.5960 −3.5750 −4.3680 −0.4280
seismic in 180°
C 57 - 0.9D + 1.0
151 39.4580 −3.7720 −3.9080 −4.1320 −5.1330 −0.4970
seismic in 210°
C 58 - 0.9D + 1.0
151 −14.8360 2.8450 0.1280 −3.2670 −5.0760 −0.4340
seismic in 240°
C 59 - 0.9D + 1.0
151 −54.5830 7.4880 3.4310 −1.2120 −4.2140 −0.2550
seismic in 270°
C 60 - 0.9D + 1.0
151 −69.1310 8.9130 5.1160 1.4820 −2.7770 −0.0080
seismic in 300°
C 61 - 0.9D + 1.0
151 −54.5830 6.7380 4.7310 4.0940 −1.1500 0.2410
seismic in 330°
Torque
(kNm)
seismic in 330°
153 C 1 - 1.00 SW 41.6630 4.9740 −2.8100 1.2800 2.1380 −0.0060
C 2 - 1.2D + 1.6Wo-
153 −487.1640 −58.8780 50.5620 54.8710 −15.4350 −4.2030
0°
C 3 - 1.2D + 1.6Wo-
153 −903.4570 −117.4050 74.1080 30.1210 6.0980 −2.3920
30°
C 4 - 1.2D + 1.6Wo-
153 −1.0413e+3 −139.9900 76.7460 1.7640 25.1570 0.1590
60°
C 5 - 1.2D + 1.6Wo-
153 −905.1220 −126.2900 59.1690 −27.1070 39.1340 2.7870
90°
C 6 - 1.2D + 1.6Wo-
153 −527.6930 −79.3590 25.1390 −50.5530 44.6530 4.7830
120°
C 7 - 1.2D + 1.6Wo-
153 34.4610 −4.7230 −18.0860 −57.7820 36.4810 5.1490
150°
C 8 - 1.2D + 1.6Wo-
153 577.0140 69.4490 −55.2970 −48.4090 19.6570 4.1660
180°
C 9 - 1.2D + 1.6Wo-
153 988.1700 127.6090 −79.9590 −27.5280 −0.9090 2.3000
210°
C 10 - 1.2D + 1.6Wo-
153 1.1673e+3 156.0520 −86.1330 0.1080 −21.0430 −0.1670
240°
C 11 - 1.2D + 1.6Wo-
153 1.0075e+3 138.4170 −66.0650 30.2690 −33.9250 −2.7550
270°
C 12 - 1.2D + 1.6Wo-
153 614.1570 88.7540 −31.0720 52.6800 −37.9950 −4.5130
300°
C 13 - 1.2D + 1.6Wo-
153 79.3540 18.2920 10.6720 61.7460 −31.6480 −5.0230
330°
C 14 - 0.9D + 1.6Wo-
153 −499.6620 −60.3700 51.4050 54.4880 −16.0770 −4.2020
0°
C 15 - 0.9D + 1.6Wo-
153 −915.9560 −118.8970 74.9510 29.7370 5.4570 −2.3900
30°
C 16 - 0.9D + 1.6Wo-
153 −1.0538e+3 −141.4820 77.5890 1.3800 24.5150 0.1600
60°
C 17 - 0.9D + 1.6Wo-
153 −917.6210 −127.7820 60.0120 −27.4910 38.4920 2.7890
90°
C 18 - 0.9D + 1.6Wo-
153 −540.1920 −80.8510 25.9820 −50.9370 44.0110 4.7850
120°

Torque
(kNm)
C 19 - 0.9D + 1.6Wo-
153 21.9620 −6.2160 −17.2420 −58.1660 35.8400 5.1510
150°
C 20 - 0.9D + 1.6Wo-
153 564.5150 67.9570 −54.4540 −48.7930 19.0150 4.1680
180°
C 21 - 0.9D + 1.6Wo-
153 975.6710 126.1160 −79.1160 −27.9120 −1.5500 2.3020
210°
C 22 - 0.9D + 1.6Wo-
153 1.1548e+3 154.5600 −85.2900 −0.2760 −21.6840 −0.1650
240°
C 23 - 0.9D + 1.6Wo-
153 995.0220 136.9250 −65.2220 29.8850 −34.5670 −2.7540
270°
C 24 - 0.9D + 1.6Wo-
153 601.6580 87.2620 −30.2290 52.2960 −38.6360 −4.5110
300°
C 25 - 0.9D + 1.6Wo-
153 66.8550 16.8000 11.5150 61.3620 −32.2890 −5.0210
330°
C 26 - 1.0D + 1.0Ws-
153 −2.2530 −0.3790 1.7120 5.9150 0.6550 −0.3760
0°
C 27 - 1.0D + 1.0Ws-
153 −36.1580 −5.2260 3.6560 3.8980 2.5320 −0.2160
30°
C 28 - 1.0D + 1.0Ws-
153 −47.4660 −7.1220 3.8570 1.4870 4.1870 0.0070
60°
C 29 - 1.0D + 1.0Ws-
153 −36.2860 −5.9910 2.3670 −1.0130 5.3670 0.2360
90°
C 30 - 1.0D + 1.0Ws-
153 −5.3380 −2.0900 −0.4870 −3.0700 5.7840 0.4090
120°
C 31 - 1.0D + 1.0Ws-
153 40.4800 4.0720 −4.0820 −3.7900 5.0400 0.4450
150°
C 32 - 1.0D + 1.0Ws-
153 84.8080 10.2220 −7.1790 −3.0970 3.5520 0.3620
180°
C 33 - 1.0D + 1.0Ws-
153 118.3210 15.0420 −9.2090 −1.3740 1.7490 0.1990
210°
C 34 - 1.0D + 1.0Ws-
153 132.7730 17.3830 −9.6790 0.9810 0.0120 −0.0180
240°
C 35 - 1.0D + 1.0Ws-
153 119.7950 15.9530 −7.9990 3.5800 −1.0850 −0.2440
270°
C 36 - 1.0D + 1.0Ws-
153 87.6350 11.8440 −5.0710 5.5580 −1.3910 −0.3990
300°
C 37 - 1.0D + 1.0Ws-
153 43.8980 6.0000 −1.5890 6.4180 −0.7870 −0.4460
330°
Torque
(kNm)
330°
C 38 - 1.2D + 1.0
153 −4.2990 −0.1700 1.5030 5.9220 0.4780 −0.3880
seismic in 0°
C 39 - 1.2D + 1.0
153 −44.0450 −5.3580 3.8700 4.1420 1.8320 −0.2120
seismic in 30°
C 40 - 1.2D + 1.0
153 −58.5930 −7.5110 4.2960 1.6630 3.3820 0.0190
seismic in 60°
C 41 - 1.2D + 1.0
153 −44.0450 −6.0520 2.6670 −0.8500 4.7140 0.2430
seismic in 90°
C 42 - 1.2D + 1.0
153 −4.2990 −1.3730 −0.5800 −2.7230 5.4700 0.4000
seismic in 120°
C 43 - 1.2D + 1.0
153 49.9950 5.2740 −4.5750 −3.4550 5.4470 0.4480
seismic in 150°
C 44 - 1.2D + 1.0
153 104.2900 12.1070 −8.2480 −2.8500 4.6530 0.3740
seismic in 180°
C 45 - 1.2D + 1.0
153 144.0360 17.2950 −10.6140 −1.0700 3.2990 0.1980
seismic in 210°
C 46 - 1.2D + 1.0
153 158.5840 19.4480 −11.0400 1.4090 1.7490 −0.0330
seismic in 240°
C 47 - 1.2D + 1.0
153 144.0360 17.9890 −9.4110 3.9220 0.4170 −0.2570
seismic in 270°
C 48 - 1.2D + 1.0
153 104.2900 13.3100 −6.1640 5.7950 −0.3390 −0.4140
seismic in 300°
C 49 - 1.2D + 1.0
153 49.9950 6.6630 −2.1690 6.5270 −0.3160 −0.4620
seismic in 330°
C 50 - 0.9D + 1.0
153 −16.7980 −1.6620 2.3470 5.5380 −0.1630 −0.3860
seismic in 0°
C 51 - 0.9D + 1.0
153 −56.5440 −6.8500 4.7130 3.7580 1.1910 −0.2100
seismic in 30°
C 52 - 0.9D + 1.0
153 −71.0920 −9.0030 5.1390 1.2790 2.7410 0.0210
seismic in 60°
C 53 - 0.9D + 1.0
153 −56.5440 −7.5440 3.5100 −1.2340 4.0730 0.2450
seismic in 90°
C 54 - 0.9D + 1.0
153 −16.7980 −2.8650 0.2630 −3.1070 4.8280 0.4020
seismic in 120°
C 55 - 0.9D + 1.0
153 37.4970 3.7820 −3.7320 −3.8390 4.8060 0.4500
seismic in 150°

Torque
(kNm)
C 56 - 0.9D + 1.0
153 91.7910 10.6150 −7.4050 −3.2340 4.0120 0.3760
seismic in 180°
C 57 - 0.9D + 1.0
153 131.5370 15.8030 −9.7710 −1.4540 2.6580 0.2000
seismic in 210°
C 58 - 0.9D + 1.0
153 146.0850 17.9560 −10.1970 1.0250 1.1070 −0.0310
seismic in 240°
C 59 - 0.9D + 1.0
153 131.5370 16.4970 −8.5680 3.5380 −0.2240 −0.2550
seismic in 270°
C 60 - 0.9D + 1.0
153 91.7910 11.8180 −5.3210 5.4110 −0.9800 −0.4120
seismic in 300°
C 61 - 0.9D + 1.0
153 37.4970 5.1710 −1.3260 6.1430 −0.9580 −0.4600
seismic in 330°

Horizontal Vertical Fy Horizontal Moment Moment Moment

Node No LoadCase Name
Fx (kN) (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
152 PLC 1 - SW 0.0509 41.3488 5.7083 -0.2023 0.0006 -0.0049
151 PLC 1 - SW -5.0247 43.8423 -2.8982 0.1088 -0.0002 -0.1916
153 PLC 1 - SW 4.9738 41.6628 -2.8101 0.1067 -0.0005 0.1782
152 PLC 2 -Wind - 0 - WindWithNoIce - 3 1.9737 694.8906 106.6222 1.1019 0.0037 -0.5057
151 PLC 2 -Wind - 0 - WindWithNoIce - 3 40.9953 -359.1663 38.3305 3.5511 0.2794 1.4441
153 PLC 2 -Wind - 0 - WindWithNoIce - 3 -40.5293 -335.7243 33.7091 2.7779 -0.2186 -0.9375
152 PLC 4 -Wind - 30 - WindWithNoIce - 3 -3.5598 583.8027 89.432 0.9147 -0.1241 1.264
151 PLC 4 -Wind - 30 - WindWithNoIce - 3 -8.6666 12.1049 11.894 3.8039 0.3006 2.1836
153 PLC 4 -Wind - 30 - WindWithNoIce - 3 -77.1085 -595.9075 48.425 1.4888 -0.1242 0.184
152 PLC 6 -Wind - 60 - WindWithNoIce - 3 -8.2769 327.8012 50.3825 0.5312 -0.2186 2.7115
151 PLC 6 -Wind - 60 - WindWithNoIce - 3 -52.6966 354.2709 -16.0404 2.9916 0.2627 2.2973
153 PLC 6 -Wind - 60 - WindWithNoIce - 3 -91.2242 -682.0721 50.0736 0.0119 0.0086 1.1766
152 PLC 8 -Wind - 90 - WindWithNoIce - 3 -10.7554 -4.6706 -0.5165 0.0129 -0.2611 3.4271
151 PLC 8 -Wind - 90 - WindWithNoIce - 3 -83.0977 601.619 -39.3659 1.4856 0.1624 1.8861
153 PLC 8 -Wind - 90 - WindWithNoIce - 3 -82.6616 -596.9485 39.0883 -1.4918 0.1455 1.9046
152 PLC 10 -Wind - 120 - WindWithNoIce - 3 -10.4991 -342.1524 -52.5705 -0.5497 -0.2398 3.2686
151 PLC 10 -Wind - 120 - WindWithNoIce - 3 -93.505 703.2077 -53.3741 -0.4188 0.01 1.0186
153 PLC 10 -Wind - 120 - WindWithNoIce - 3 -53.3295 -361.0552 17.8191 -2.713 0.2495 2.192
151 PLC 12 -Wind - 150 - WindWithNoIce - 3 -75.3974 596.4464 -51.2961 -2.2066 -0.149 -0.2446
153 PLC 12 -Wind - 150 - WindWithNoIce - 3 -6.6825 -9.7092 -9.1959 -3.0895 0.2686 1.7665
Horizontal Vertical Fy Horizontal Moment Moment Moment

Node No LoadCase Name
Fx (kN) (kN) Fz (kN) Mx (kNm) My (kNm) Mz (kNm)
151 PLC 14 -Wind - 180 - WindWithNoIce - 3 -39.1236 344.037 -36.802 -3.4508 -0.2588 -1.4182
153 PLC 14 -Wind - 180 - WindWithNoIce - 3 39.6755 329.3864 -32.4533 -2.6013 0.2174 0.8902
152 PLC 16 -Wind - 210 - WindWithNoIce - 3 3.4799 -585.9343 -89.659 -0.9079 0.1272 -1.2311
151 PLC 16 -Wind - 210 - WindWithNoIce - 3 7.3893 -0.4246 -12.5703 -3.78 -0.299 -2.189
153 PLC 16 -Wind - 210 - WindWithNoIce - 3 76.025 586.3589 -47.8671 -1.5137 0.1202 -0.181
152 PLC 18 -Wind - 240 - WindWithNoIce - 3 8.9927 -327.996 -50.9297 -0.581 0.2204 -2.8998
151 PLC 18 -Wind - 240 - WindWithNoIce - 3 54.9933 -370.3456 17.0853 -3.0265 -0.2799 -2.349
153 PLC 18 -Wind - 240 - WindWithNoIce - 3 93.802 698.3416 -51.7258 -0.0744 -0.0083 -1.2296
152 PLC 20 -Wind - 270 - WindWithNoIce - 3 10.8497 10.8603 1.2817 -0.0217 0.2522 -3.4572
151 PLC 20 -Wind - 270 - WindWithNoIce - 3 83.8424 -609.3139 39.9066 -1.4692 -0.1616 -1.8598
153 PLC 20 -Wind - 270 - WindWithNoIce - 3 82.7802 598.4536 -39.1829 1.4965 -0.1431 -1.9006
151 PLC 22 -Wind - 300 - WindWithNoIce - 3 91.5221 -693.3848 52.1844 0.3681 -0.01 -0.9423
153 PLC 22 -Wind - 300 - WindWithNoIce - 3 51.741 352.6011 -17.3124 2.6637 -0.2347 -2.1125
151 PLC 24 -Wind - 330 - WindWithNoIce - 3 76.8136 -609.0749 51.991 2.1722 0.148 0.244
153 PLC 24 -Wind - 330 - WindWithNoIce - 3 7.7021 18.3491 8.7773 3.1359 -0.2612 -1.7819
5 CONDITION OF ANALYSIS
This CALCULATION REPORT has been prepared based on the site inspection and the relevant information
and data provided to the undersigned. The conclusion and recommendation contained in this report
pertain only to the computer analysis of this structure and its load carrying capacity.

6 REFERENCES
• Association of Structural Engineers of the Philippines, National Structural Code of the Philippines 2015,
Volume I, Buildings, Towers, and Other Vertical Structures, 7th Edition. Chapter 1.
• American Concrete Institute ACI-318-14M, Building Code Requirements for Concrete Works.
• AISC Manual of Steel Construction, “Specification for Design Fabrication and Erection of Structural Steel ”
15th Edition, 2016


StructDesign (GFSST - LRFD - TIA222G) 3GT-40-330C-Z-350C

Uploaded by

Copyright:

Available Formats

StructDesign (GFSST - LRFD - TIA222G) 3GT-40-330C-Z-350C

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

StructDesign (GFSST - LRFD - TIA222G) 3GT-40-330C-Z-350C

Uploaded by

Copyright:

Available Formats

What are the design parameters and criteria considered in the structural analysis and design?

What are the design parameters and criteria considered in the structural analysis and design?

What are the results and findings of the structural analysis of the existing tower structure?

What are the results and findings of the structural analysis of the existing tower structure?

DITO TELECOMMUNITY

Structural Investigation Report of

Project Name: Design of a 40m High 3-Legged

0 12/23/21 Structural design of the proposed

Rev. Date Pages Description Approved Date

MEG Structural Design - 0

4 DESIGN COMPUTATIONS .......................................................................................... 14

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C -1- Marjie S. Erispe-Gadon

Qty Antenna Type Antenna Size, m Elev., m AGL Antenna Status

3 L700 2ports 18.5dbi 2.580x0.550x0.146 38.5 proposed

3 T2020L6R011 2.090x0.499x0.199 38.5 proposed

3 AAU-NR-64TR 0.85x0.47x0.17 35.5 proposed

9 RRU-2.6G-8T8R 0.48x0.356x0.14 38.5/35.5 proposed

2 MW Ø0.60 33.0 proposed

1 MW Ø1.80 31.0 proposed

1 MW Ø1.20 28.0 proposed

ENGR. MARJIE S. ERISPE-GADON

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 2 Marjie S. Erispe-Gadon

2 DESIGN PARAMETERS AND CRITERIA

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 3 Marjie S. Erispe-Gadon

Reinforced Concrete 24 kN/m³

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 4 Marjie S. Erispe-Gadon

2.6.1 Lateral Forces

𝐶𝐶𝑓𝑓 = 4.0𝜀𝜀2 − 5.9𝜀𝜀 + 4.0 for square tower cross section

𝐶𝐶𝑓𝑓 = 3.4𝜀𝜀2 − 4.7𝜀𝜀 + 3.4 for triangular tower cross section

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 6 Marjie S. Erispe-Gadon

2.6.2 Other Design Reaction Loads from Appurtenances and Ancillaries

Qty Antenna Antenna Size, m Elev., m Qty - - all legs -

3 L700 2ports 2.580x0.550x0.146 38.5 3 - - all legs -

3 T2020L6R011 2.090x0.499x0.199 38.5 3 - - all legs -

3 AAU-NR-64TR 0.85x0.47x0.17 35.5 3 - - all legs -

9 RRU-2.6G- 0.48x0.356x0.14 38.5/35.5 9 - - all legs -

2 MW Ø0.60 33.0 2 - - A and B -

Load Load Combination per TIA-222-G

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 7 Marjie S. Erispe-Gadon

Load Load Combination per TIA-222-G

Dead, D 1.20 1.20 0.90 0.90

Wind, W 1.60 - 1.60 -

Earthquake, E - 1.00 - 1.00

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 8 Marjie S. Erispe-Gadon

Lateral Brace Remarks(Indic

brace for work

└75x75x6 main Varies (See

└75x75x6 main Varies (See

└75x75x6 main Varies (See

└125x125x10 Varies (See

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 9 Marjie S. Erispe-Gadon

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 10 Marjie S. Erispe-Gadon

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 11 Marjie S. Erispe-Gadon

3.4 Results and Findings

Horizontal (Main Diagonal (Main Lateral Brace /

brace for work

brace for work

StructDesign(GFSST_LRFD_TIA222G) 3GT-40-330C-Z-350C 12 Marjie S. Erispe-Gadon

3.5 Conclusion and Recommendations