BS en 00071-2-2020
BS en 00071-2-2020
BS en 00071-2-2020
EN 71‑2:2020
Safety of toys
Part 2: Flammability
BS EN 71‑2:2020 BRITISH STANDARD
National foreword
This British Standard is the UK implementation of EN 71‑2:2020. It
supersedes BS EN 71‑2:2011+A1:2014, which is withdrawn.
The UK participation in its preparation was entrusted to Technical
Committee CW/15, Safety of toys.
A list of organizations represented on this committee can be obtained on
request to its committee manager.
This publication does not purport to include all the necessary provisions
of a contract. Users are responsible for its correct application.
ISBN 978 0 539 01300 9
ICS 13.220.40; 97.200.50
Compliance with a British Standard cannot confer immunity from
legal obligations.
This British Standard was published under the authority of the
Standards Policy and Strategy Committee on 31 December 2020.
English Version
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 71-2:2020 E
worldwide for CEN national Members.
BS EN 71‑2:2020
EN 71-2:2020 (E)
Contents Page
European foreword....................................................................................................................................................... 4
Introduction .................................................................................................................................................................... 6
1 Scope .................................................................................................................................................................... 6
2 Normative references .................................................................................................................................... 6
3 Terms and definitions ................................................................................................................................... 7
4 Requirements ................................................................................................................................................... 9
4.1 General requirements ................................................................................................................................... 9
4.2 Toys to be worn on the head (see A. 3).................................................................................................... 9
4.2.1 General ................................................................................................................................................................ 9
4.2.2 Beards, moustaches, wigs, etc., made from pile or flowing elements which protrude
50 mm or more from the surface of the toy ........................................................................................ 10
4.2.3 Beards, moustaches, wigs, etc., made from pile or flowing elements which protrude
less than 50 mm from the surface of the toy ...................................................................................... 10
4.2.4 Full or partial moulded head masks ..................................................................................................... 10
4.2.5 Toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods,
headdresses including upward protruding items and masks not covered by 4.2.4
which partially or fully cover the head (e.g. fabric and paperboard masks, eye masks,
face masks), but excluding those items covered by 4.3.................................................................. 10
4.3 Toy disguise costumes and toys intended to be worn by a child in play (see A.4) ............... 10
4.4 Toys intended to be entered by a child (see A.5).............................................................................. 11
4.5 Soft-filled toys (see A.6) ............................................................................................................................. 11
5 Test methods ................................................................................................................................................. 11
5.1 General ............................................................................................................................................................. 11
5.1.1 Test burner ..................................................................................................................................................... 11
5.1.2 Conditioning and test chamber ............................................................................................................... 11
5.1.3 Test flame........................................................................................................................................................ 12
5.2 Test relating to beards, moustaches, wigs, etc., made from pile or flowing elements,
which protrude 50 mm or more from the surface of the toy........................................................ 12
5.2.1 Test flame........................................................................................................................................................ 12
5.2.2 Test burner position ................................................................................................................................... 12
5.2.3 Test performance ......................................................................................................................................... 12
5.3 Test relating to beards, moustaches, wigs, etc., made from pile or flowing elements,
which protrude less than 50 mm from the surface of the toy, and full or partial
moulded head masks (see A.7)................................................................................................................ 12
5.3.1 Test flame........................................................................................................................................................ 12
5.3.2 Test burner position ................................................................................................................................... 12
5.3.3 Test performance ......................................................................................................................................... 12
5.4 Test relating to toys to be worn on the head (4.2.5), hoods, headdresses including
upward protruding items and masks not covered by 4.2.4 which partially or fully
cover the head (e.g. fabric and paperboard masks, eye masks, face masks), toy
disguise costumes and toys intended to be worn or toys intended to be entered by a
child (see A.8) ................................................................................................................................................ 12
5.4.1 Preparation of test specimen ................................................................................................................... 13
5.4.2 Holding and positioning the test specimen ........................................................................................ 16
5.4.3 Test flame........................................................................................................................................................ 17
5.4.4 Test burner position ................................................................................................................................... 17
5.4.5 Test performance ......................................................................................................................................... 18
5.4.6 Results .............................................................................................................................................................. 18
2
BS EN 71‑2:2020
EN 71-2:2020 (E)
5.5 Test for soft-filled toys and certain soft-filled parts of toy disguise costumes....................... 19
5.5.1 Test flame ........................................................................................................................................................ 19
5.5.2 Test burner position .................................................................................................................................... 19
5.5.3 Test performance ......................................................................................................................................... 19
Annex A (informative) Background and rationale for this document .................................................... 20
A.1 General ............................................................................................................................................................. 20
A.2 General requirements (see 4.1) .............................................................................................................. 20
A.3 Toys to be worn on the head (see 4.2) .................................................................................................. 20
A.4 Toy disguise costumes and toys intended to be worn by a child in play (see 4.3) ................ 26
A.5 Toys intended to be entered by a child (see 4.4) .............................................................................. 27
A.6 Soft-filled toys (see 4.5) .............................................................................................................................. 27
A.7 Test relating to toy disguise costumes and toys intended to be entered by a child
(see 5.4) ............................................................................................................................................................ 28
A.8 Suggestions to help reduce rate of spread of flames for toy disguise costumes. ................... 28
A.9 Flowcharts showing how to obtain test specimens from toy disguise costumes .................. 29
Annex B (informative) Significant technical changes between this European and the
previous version ........................................................................................................................................... 32
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2009/48/EC aimed to be covered............................................... 34
Bibliography ................................................................................................................................................................. 35
3
BS EN 71‑2:2020
EN 71-2:2020 (E)
European foreword
This document (EN 71-2:2020) has been prepared by Technical Committee CEN/TC 52 “Safety of toys”,
the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2021, and conflicting national standards shall be
withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Additional information on the background and rationale for various requirements are given in Annex A.
Annex B provides details of significant technical changes between this document and the previous
edition.
This document has been prepared under mandate M/445 given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive 2009/48/EC.
For relationship with EU Directive 2009/48/EC, see informative Annex ZA, which is an integral part of
this document.
This document constitutes the second part of the EN 71 series of standards on safety of toys.
— Part 2: Flammability
— Part 13: Olfactory board games, cosmetic kits and gustative games
4
BS EN 71‑2:2020
EN 71-2:2020 (E)
NOTE 1 In addition to the above parts of EN 71, the following guidance documents have been published:
— CEN/TR 15071, Safety of toys — National translations of warnings and instructions for use in EN 71, and
— CEN/TR 16918, Safety of toys - Children’s mouthing behaviour in contact with toys
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
5
BS EN 71‑2:2020
EN 71-2:2020 (E)
Introduction
This document aims at reducing, as far as possible, those hazards which are not evident to users; it does
not cover inherent hazards that are obvious to children or the persons in charge of them. Assuming that
the toys are used in the intended manner, they should not present any further hazard to children for
whom they are intended (according to the Directive 2009/48/EC “intended for use by” means that a
parent or supervisor shall reasonably be able to assume by virtue of the functions, dimensions and
characteristics of a toy that it is intended for use by children of the stated age group). Allowance should
also be made for foreseeable use, bearing in mind the behaviour of children who do not generally share
the same degree of care as the average adult user.
As a general rule, toys are designed and manufactured for particular ages of children. Their
characteristics are related to the age and stage of development of the children, and their use presupposes
certain aptitudes.
Accidents are frequently due to a toy either being given to a child for whom it is not intended or being
used for a purpose other than that for which it was designed. Great care should therefore be taken when
choosing a toy; account should be taken of the mental and physical development of the child who will be
using it.
The requirements of this document do not release parents or carers from their responsibility of
supervising the child while he or she is playing.
1 Scope
This document specifies the categories of flammable materials which are prohibited in all toys, and
requirements concerning flammability of certain toys when they are subjected to a small source of
ignition.
The test methods described in Clause 5 are used for the purposes of determining the flammability of toys
under the particular test conditions specified. The test results thus obtained are not considered as
providing an overall indication of the potential fire hazard of toys or materials when subjected to other
sources of ignition.
This document includes general requirements relating to all toys and specific requirements and methods
of test relating to the following toys, which are considered as being those presenting the greatest hazard:
— toys to be worn on the head: beards, moustaches, wigs, etc. made from pile or flowing elements;
masks; hoods, headdresses, etc.; However, paper and paperboard hats without embellishments or
attachments are excluded;
— toys intended to be entered by a child and constructed from textiles and/or polymer sheets and films;
— soft-filled toys.
NOTE Additional requirements for flammability of electric toys are specified in EN 62115[2]
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 2431:2019, Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2019)
6
BS EN 71‑2:2020
EN 71-2:2020 (E)
EN ISO 6941:2003, Textile fabrics - Burning behaviour - Measurement of flame spread properties of
vertically oriented specimens (ISO 6941:2003)
3.1
chemical toy
toy intended for the direct handling of chemical substances and mixtures and which is used in a manner
appropriate to a given age-group and under the supervision of an adult
[SOURCE EN 71-4:2013[3]]
3.2
cleansing
wipe with dry or damp cloth to remove surface soiling
3.3
extremely flammable liquid
liquid having a flash point < 23 °C and initial boiling point ≤35 °C
3.4
flaming debris
material that becomes detached from the specimen during the test procedure and continues to flame as
it falls
3.5
flammability
ability of a material or a product to burn with a flame under specified test conditions
3.6
flammable gas
gas or gas mixture having a flammable range with air at 20 °C and a standard pressure of 101,3 kPa
3.7
flammable liquid
liquid having a flash point ≥ 23 °C and ≤ 60 °C
3.8
flowing elements
loosely hanging elements having the ability to flow like hair, to hang closely to the shape of the head and
continue to move on their own after the head is rotated then stopped
7
BS EN 71‑2:2020
EN 71-2:2020 (E)
Note 1 to entry: Imitation hair, free hanging ribbons, paper or cloth strands are examples of flowing elements.
3.9
highly flammable liquid
liquid having a flash point < 23 °C and initial boiling point > 35 °C
3.10
highly flammable solid
material with similar behaviour in fire as celluloid (cellulose nitrate), i.e. ignites instantaneously as a
result of a brief contact with a flame and proceeds to burn very rapidly
3.11
molten drips
falling droplets of molten material
3.12
moulded head mask
mask that is moulded to the contours of the head or face
3.13
soft-filled toy
toy, with soft body surfaces and filled with soft material, readily allowing compression of the main part
of the toy with the hand
3.14
surface flash
rapid spread of flame over the surface of a material without ignition of its base structure at the same time
3.15
toy disguise costume
costume intended to be worn by children to facilitate imaginative play where the child pretends to be a
character
Note 1 to entry: Costumes and garments for children less than 12 months old are not regarded as toy disguise
costumes since such children are unable to engage in character role-play (see A.4).
Note 2 to entry: A toy disguise costume can be a single article or a clothing ensemble with multiple articles. A
wizard’s cloak or a princess’s dress are examples of single article toy disguise costumes. A superhero’s cape and
bodice and gloves are examples of a clothing ensemble with multiple articles.
3.16
toys intended to be entered by a child
toy constructed from fabric and/or polymer sheets and films that are intended to fully or almost fully
enclose a child on all sides
Note 1 to entry: Tents, puppet theatres, wigwams, tepees and play tunnels are examples of toys intended to be
entered by a child.
3.17
washing
process designed to clean textile articles in an aqueous bath
8
BS EN 71‑2:2020
EN 71-2:2020 (E)
Note 1 to entry: Washing includes all or some of the following operations in relevant combinations:
— soaking, pre-washing and main washing - carried out usually with heating, mechanical action and in the
presence of detergents or other products - and rinsing;
— water extraction, i.e. spinning or wringing performed during and/or at the end of the operations mentioned
above.
4 Requirements
4.1 General requirements
— materials with a piled surface which produce surface flash when a flame is applied to the tested
material under the conditions described in 5.5. Piled surfaces showing no momentary area of flame
over the area of the piled surface remote from the test flame are considered to meet this requirement.
Specific materials to which the test flame is applied in order to check compliance of the toy with
requirements in 4.2 to 4.5 are considered to comply with the above requirements if the toy meets its
appropriate requirements in 4.2 to 4.5.
In addition, toys shall not contain flammable gases, extremely flammable liquids, highly flammable liquids,
flammable liquids and flammable gels except as provided for below:
— flammable liquids and flammable gels supplied in sealed containers having a maximum volume of
15 ml per container;
— highly flammable liquids and flammable liquids being entirely retained within a porous material in
capillary channels of writing instruments;
— flammable liquids with a viscosity greater than 260 × 10−6 m2/s corresponding to a flow time of more
than 38 s when determined in accordance with EN ISO 2431:2019 using cup No. 6;
— highly flammable liquids contained in chemical toys, and in olfactory board games, cosmetic kits and
gustative games, as defined in 2009/48/EC.
— masks;
9
BS EN 71‑2:2020
EN 71-2:2020 (E)
but not to paper or paperboard hats unless they have embellishments or attachments that form flowing
elements.
When a product incorporates several features, for example a hat with an attached mask and hair, each
part shall be tested separately to the applicable clause relevant to that particular part of the toy.
Attachments which are used for the purpose of securing a mask, hat, etc., on the head (e.g. string, elastic,
plastic strap) shall not be tested (see A.3).
4.2.2 Beards, moustaches, wigs, etc., made from pile or flowing elements which protrude 50 mm
or more from the surface of the toy
When tested according to 5.2, the duration of flaming shall not be more than 2 s after the removal of the
test flame.
In addition, if ignition occurs, the maximum-burnt length of pile, or flowing elements shall not be:
a) more than 50 % of the greatest initial length, when the initial length was 150 mm or more, or;
b) more than 75 % of the greatest initial length, when the initial length was less than 150 mm.
When determining whether materials are required to be tested under 4.2.2, the distance by which the
material protrudes shall be measured without applying tension to the protruding part, e.g. curly hair is
not straightened. Plaits or braided hair shall be fully released and combed, where possible, before testing.
4.2.3 Beards, moustaches, wigs, etc., made from pile or flowing elements which protrude less
than 50 mm from the surface of the toy
Beards, moustaches, wigs, etc. made from pile or flowing elements which protrude 5 mm or less from the
surface of the toy are regarded as headdresses and are covered by 4.2.5.
When tested in accordance with 5.3 the duration of flaming shall not be more than 2 s after the removal
of the test flame, and the maximum distance between the upper edge of the burnt area and the point of
application of the test flame shall not be more than 70 mm.
4.2.4 Full or partial moulded head masks
When tested in accordance with 5.3, the duration of flaming shall not be more than 2 s after the removal
of the test flame. The maximum distance between the upper edge of the burnt area and the point of
application of the test flame shall not be more than 70 mm.
This requirement does not apply to moulded eye masks that neither cover the chin nor a cheek as they
are covered by 4.2.5.
4.2.5 Toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses
including upward protruding items and masks not covered by 4.2.4 which partially or fully cover
the head (e.g. fabric and paperboard masks, eye masks, face masks), but excluding those items
covered by 4.3
When tested in accordance with 5.4, the rate of spread of flame of the test specimen shall not exceed
10 mm/s or the test specimen shall self-extinguish.
4.3 Toy disguise costumes and toys intended to be worn by a child in play (see A.4)
This requirement does not apply to separate toys to be worn on the head, which are supplied with a toy
disguise costume.
When tested in accordance with 5.5 parts of toy disguise costumes and toys intended to be worn by
children in play which contain loose stuffing which would fall out if tested in accordance with 5.4.1.2 shall
not exceed 30 mm/s rate of spread of flame or the test specimen shall self-extinguish.
10
BS EN 71‑2:2020
EN 71-2:2020 (E)
This requirement does not apply to soft-filled parts which, when positioned in accordance with 5.5.3,
present a maximum unhindered vertical soft-filled height of 150 mm or less.
When tested in accordance with 5.4 all other toy disguise costumes and toys intended to be worn by a
child in play (and parts thereof), shall not exceed 30 mm/s rate of spread of flame or the test specimen
shall self-extinguish.
In all cases if the rate of spread of flame is between 10 mm/s and 30 mm/s, the appropriate component(s)
of the toy and the packaging shall be permanently marked with the following warning: “Warning. Keep
away from fire”.
4.4 Toys intended to be entered by a child (see A.5)
These include for example toy tents, puppet theatres, wigwams, tepees and play tunnels.
When tested in accordance with 5.4, the rate of spread of flame of the test specimen shall not exceed
30 mm/s or the test specimen shall self-extinguish.
If the test specimen has a rate of spread of flame greater than 20 mm/s when tested in accordance with
5.4, there shall be no flaming debris or molten drips.
If the material has non-identical surfaces, both sides shall be tested.
If the rate of spread of flame is between 10 mm/s and 30 mm/s, the appropriate components(s) of the
toy and the packaging shall be permanently marked with the following warning: “Warning. Keep away
from fire”.
4.5 Soft-filled toys (see A.6)
— toys which, when positioned in accordance with 5.5.3, present a maximum unhindered vertical soft-
filled height of 150 mm or less.
When tested in accordance with 5.5, the rate of spread of flame on the surface shall not be more than
30 mm/s or the toy shall be self-extinguishing.
5 Test methods
5.1 General
5.1.1 Test burner
The test flame shall be obtained from a burner as described in EN ISO 6941:2003, Annex A and shall be
operated with butane or propane gas.
5.1.2 Conditioning and test chamber
Before each test, the toys or test specimens shall be conditioned for at least 7 h in an atmosphere having
a temperature of (20 ± 5) °C and a relative humidity of (65 ± 5) %.
Carry out the tests in a test chamber in which the movement of air is less than 0,2 m/s at the start of the
test and is not affected by operation of mechanical apparatus during the test. It is essential that the
volume of air in the test chamber is not affected by a reduction in the level of oxygen concentration. When
an open fronted chamber is used for the test, ensure that the test specimen is at least 300 mm from the
walls of the chamber. Maintain the chamber at 10 °C to 30 °C and at a relative humidity of 15 % to 80 %
prior to the test being carried out.
11
BS EN 71‑2:2020
EN 71-2:2020 (E)
The toys or test specimens shall be tested within 5 min of removal from the conditioning atmosphere.
5.1.3 Test flame
Light the burner described in 5.1.1 and pre-heat for a minimum of 2 min.
The required height of the flame shall be measured from the end of the burner tube to the top of the flame
with the burner in the vertical position.
5.2 Test relating to beards, moustaches, wigs, etc., made from pile or flowing elements,
which protrude 50 mm or more from the surface of the toy
5.2.1 Test flame
Measure the length of the pile or flowing elements and position the toy so that the largest dimension of
the pile or flowing elements hangs vertically or as near vertically as possible.
Apply the test flame for (2 ± 0,5) s to the lower edge or ends of the specimen material so that the flame
penetrates the element by approximately 10 mm.
If ignition occurs, measure the duration of flaming and the maximum burnt length, i.e. the maximum
length of the pile or flowing elements that has been burnt.
5.3 Test relating to beards, moustaches, wigs, etc., made from pile or flowing elements,
which protrude less than 50 mm from the surface of the toy, and full or partial moulded
head masks (see A.7)
5.3.1 Test flame
If ignition occurs, measure the duration of flaming and the maximum distance between the upper edge of
the burnt area and the point of application of the flame.
5.4 Test relating to toys to be worn on the head (4.2.5), hoods, headdresses including
upward protruding items and masks not covered by 4.2.4 which partially or fully cover
the head (e.g. fabric and paperboard masks, eye masks, face masks), toy disguise
12
BS EN 71‑2:2020
EN 71-2:2020 (E)
costumes and toys intended to be worn or toys intended to be entered by a child (see
A.8)
5.4.1 Preparation of test specimen
5.4.1.1 General
Each test shall be carried out on material taken from a new toy, prepared as described below. It is
acceptable to wash test specimens prepared according to 5.4.1.2 rather than the whole toy.
Toy disguise costumes shall be subjected to testing before and after washing and shall be washed in
accordance with any care instructions from the manufacturer. If there are no care instructions or an
instruction not to wash or an instruction to cleanse the surface of the toy only, then the toy disguise
costume shall be treated in accordance with 5.4.1.1 c).
For other toys, if the advice given to the consumer (for example a care label on the toy or its packaging):
a) indicates that the toy is not intended to be washed or cleansed, it shall not be washed or cleansed
before testing;
b) recommends a method of washing or cleansing the toy shall be treated once in accordance with these
recommendations;
c) gives no information relating to washing or cleansing the toy, and if it is likely to be washed during
its life, the test specimens(s) shall be treated, before testing, in accordance with the following
instructions:
Immerse the test specimens(s) in water at (20 ± 3) °C and having a calcium hardness of 8 to 14dH
(80 mg/L CaO to 140 mg/L CaO) at a ratio of at least 1:20 mass of test specimen(s) to volume of
water, and allow it/them to stand for (10 ± 1) min. Drain and repeat twice. Rinse by immersing the
test specimen(s) in demineralized water for (2 ± 0,5) min. Drain and dry by a method appropriate to
the test specimen(s) and, where appropriate, restore the pile as near as possible to its original
condition.
5.4.1.2.1 General
Take a test specimen or a combined test specimen from each different material and where possible,
ensure the lower edge of the test specimen includes the lower edge of the costume material.
NOTE Textile materials of the same fabric but a different colour are regarded as the same material.
Where there is sufficient material, cut the test specimen with the length corresponding to the vertical
direction when the toy is worn. In case of insufficient material, priority shall be given to making combined
test specimens taken in the vertical direction, rather than full-size or half-size test specimens taken in the
horizontal direction.
When preparing pieces for a combined test specimen, ensure the longer piece is taken in the vertical
direction if this is possible, and in any case, locate the longer piece in the lower half of the combined test
specimen. If a combined test specimen is formed from 2 pieces of similar size and cut in different
directions, the piece from the vertical direction shall be located in the lower half of the combined test
specimen.
When forming a combined test specimen, in order to ensure that there is no gap at the overlap, the 2
pieces shall be overlapped by (10± 2) mm and joined using vertically orientated metal staples of sufficient
13
BS EN 71‑2:2020
EN 71-2:2020 (E)
gauge to maintain the integrity of the joint when handing the test specimen (e.g. 22/6) spaced at 5
equidistant points from the edge of the test specimen holder specified in 5.4.2.
Figure 1, shows the correct orientation of combined test specimen pieces
Key
1 Piece taken in vertical orientation from the toy
2 Overlap join using 5 vertical staples
3 Piece taken in horizontal orientation
Correct orientation
Incorrect orientation
Filling materials (e.g. fibre wadding, foam fillings) which do not drop out of the test specimen shall be
regarded as a single material for the purpose of test specimen preparation (i.e. fabric plus filling). Test
specimens that include filling materials shall be prepared in accordance with 5.4.1.2.6 or 5.4.1.2.7.
Seams, decorative trims, embellishments etc. with the exception of finished lowest edges of the costume
or the cuff edges of sleeves, shall not be included in test specimens that are prepared in accordance with
5.4.1.2.2 to 5.4.1.2.5.
Obtain test specimens in the following order:
a) where possible take a full-size test specimen (5.4.1.2.2) but if there is insufficient material, make up
a combined full-size test specimen (5.4.1.2.3). Where there is insufficient material to make up a
combined full-size test specimen take a half-size test specimen (5.4.1.2.4) and if that is not possible,
make up a combined half-size test specimen (5.4.1.2.5);
b) when all test specimens have been taken in accordance with 5.4.1.2.1 a), further test specimens are
taken in accordance with 5.4.1.2.6, provided there is sufficient material;
c) when all test specimens have been taken in accordance with 5.4.1.2.1 b), further test specimens are
taken in accordance with 5.4.1.2.7, provided there is sufficient material and the material was not
previously prepared according to 5.4.1.2.1 a) and b);
14
BS EN 71‑2:2020
EN 71-2:2020 (E)
d) where there is insufficient material to make up a test specimen in accordance with 5.4.1.2.1 a) to c)
no test is performed.
Take a single piece test specimen with dimensions of at least 610 mm × 100 mm.
5.4.1.2.3 Combined full-size test specimen
Where there is insufficient material to prepare a test specimen in accordance with 5.4.1.2.2, make up a
test specimen with dimensions of at least 610 mm × 100 mm from two separate pieces of the same
material. The 2 pieces shall be orientated and joined using metal staples as described in 5.4.1.2.1.
5.4.1.2.4 Half-size test specimen
Where there is insufficient material to prepare a test specimen in accordance with 5.4.1.2.3, take a test
specimen with dimensions of at least 310 mm × 100 mm.
5.4.1.2.5 Combined half-size test specimen
Where there is insufficient material to prepare a test specimen in accordance with 5.4.1.2.4 make up a
test specimen with dimensions of at least 310 mm × 100 mm from two pieces of the same material, of
dimensions at least 160 mm x 100 mm. The 2 pieces shall be orientated and joined using metal staples as
described in 5.4.1.2.1.
5.4.1.2.6 Test specimens that include fillings or features such as seams, trims and
embellishments
Prepare full-size test specimens of materials that contain fillings or features (e.g. prints, appliques, trims,
embellishments, patchwork material, vertically orientated seams) from a single piece of material with
dimensions of at least 610 mm x 100 mm.
Where there is insufficient material to prepare a full-size test specimen prepare a half-size test specimen
with dimensions of at least 310 mm × 100 mm.
The test specimens are only taken in the vertical direction when the toy is in use. The lower edge of the
test specimen (to which the test flame will be applied) shall be representative of the lowest edge of the
costume or the cuff edge of a sleeve. If the lowest edge or sleeve cuff is not an even length (e.g. zig-zagged)
then trim the bottom edge to produce a straight edge to aid measurement and testing.
If the specimen includes a vertically orientated seam, take the test specimen so that the seam will be
located approximately in the centre of the test specimen holder specified in 5.4.2.
If the toy disguise costume has to be cut to form the test specimen the filling or feature should be placed
approximately in the centre of the test specimen.
NOTE This can mean that the trimmed bottom edge of the test specimen is not necessarily the lowest point on
the bottom edge of the toy disguise costume.
For materials that cannot be prepared in accordance with 5.4.1.2.2 to 5.4.1.2.6 cut a single test specimen
at least 310 mm × 40 mm, provided there is sufficient material. Seams, trims, embellishments etc., shall
not be included in the test specimen but fillings are permitted.
Cut the test specimen with the greater dimension corresponding to the vertical direction when the toy is
worn.
5.4.1.3 Test specimens from toys worn on the head with flowing elements (4.2.5), hoods,
headdresses including upward protruding items and masks not covered by 4.2.4 which partially
15
BS EN 71‑2:2020
EN 71-2:2020 (E)
or fully cover the head (e.g. fabric and paperboard masks, eye masks, face masks), and toys
intended to be worn (4.3) or toys intended to be entered by a child (4.4)
Cut test specimens with dimensions of at least 610 mm × 100 mm from each material available on the
toy. Each test specimen shall be made of one material. Where there is enough material, cut the test
specimen with the length corresponding to the vertical direction of the toy when in use. Where possible,
the test specimen should not include seamed edges. As seams can modify the rate of spread of flame, they
shall be placed in the upper part of the specimen holder specified in 5.4.2.
Where there is insufficient material to prepare a full-size test specimen as described above, it is
permissible to use a test specimen made up of two separate pieces of the same material measuring at
least 310 mm × 100 mm each which, when fitted together with an overlap of 10 mm, will constitute a test
specimen of at least 610 mm × 100 mm. The 2 pieces shall be joined using metal staples as described in
5.4.1.2.1.
In the case of toys to be entered by a child (4.4), if the material has non-identical surfaces, both sides shall
be tested.
5.4.2 Holding and positioning the test specimen
Mount the test specimen on the test specimen holder as shown in Figure 2.
For narrow materials prepared in accordance with 5.4.1.2.7 the test specimen shall be supported in the
holder by a stainless-steel wire mesh of (18 × 18 +4/-0 mm) grid size with a wire diameter of
(1 ± 0,4 mm). See Figure 2b)
The specimens shall be secured under slight tension to avoid creases, waving, or curling by suitable
means that do not affect ignition or flame spread.
For toys corresponding to 4.2.5 and 4.3, the outside surface of the material, when in use, shall be
positioned with their outer surface uppermost.
Attach 100 % cotton marker threads as per Figure 2a across the specimen at no more than 2 mm from
the surface of the test specimen, with a device to indicate when the marker thread is severed. In the case
of full-size test specimens use marker thread A and C. For half-size test specimens use marker thread B
and C.
Position the specimen holder at 45 (±1) ° to the horizontal.
16
BS EN 71‑2:2020
EN 71-2:2020 (E)
Dimensions in millimetres
Position the burner vertically (90 ± 2) ° to the horizontal in order to have a distance of (30 ± 2) mm
between the centre of the lower edge of the test specimen and the top of the burner (see Figure 3).
17
BS EN 71‑2:2020
EN 71-2:2020 (E)
Dimensions in millimetres
Key
A, B and C Location of 100 % cotton marker threads
1 Test specimen
2 Burner
Apply the test flame to the centre of the lower edge of the test specimen as shown in Figure 3, for (10 ± 1)
s.
If flaming occurs, start the timing device when the first marker thread is severed by the flame and stop it
when the second marker thread is severed.
5.4.6 Results
If, after applying the flame, the test specimen fails to ignite, record the material as “Did not ignite.”
If the test specimen ignites but the first marker thread is not severed, record the rate of spread of flame
as “Self-extinguished within 50 mm of flame application.”
If flaming occurs and the first marker thread is severed and the flame extinguishes before severing the
second marker thread, record the material tested as “Self-extinguishing.”
If the second marker thread is severed, note the time and calculate the rate of spread of flame in mm/s.
Round the resulting value to the nearest mm/s.
18
BS EN 71‑2:2020
EN 71-2:2020 (E)
5.5 Test for soft-filled toys and certain soft-filled parts of toy disguise costumes
5.5.1 Test flame
Determine the maximum unhindered soft-filled dimension of the toy and if this is greater than 150 mm,
position the toy so that this dimension is vertically orientated in a suitable clamp.
Soft-filled toys shall be tested as supplied, including any clothing or cover present with the toy and, if
considered to be more onerous, with the clothes or cover removed if removal can be accomplished
without damage to the clothes, cover or toy.
Applicable soft-filled parts of toy disguise costumes shall be prepared in accordance with 5.4.1.1.
Apply the test flame to the toy for (3 ± 0,5) s so that the distance between the edge of the burner tube and
the toy is (5 ± 2) mm and the test flame makes contact between 20 mm and 50 mm above the lower edge
of the most flammable soft-filled material of the toy, as predetermined, and is not less than 120 mm from
the top of the maximum soft-filled dimension of the toy.
If the test flame application point for the most flammable soft-filled material cannot be located at a
distance 120 mm or more from the top of the maximum soft-filled dimension of the toy, the next most
flammable soft-filled material located 120 mm or more from the top of the maximum soft-filled
dimension of the toy shall be chosen for the application of the test flame.
In general, predetermination of the most flammable soft-filled material should be carried out by
observation of the flame spread while the specimen is burning during the first test. Specimens that self-
extinguish with little damage occurring can be tested using a test flame application point on a different
material higher up the specimen provided that the self-extinguishing flame has been remote from the
area of new material.
After removal of the test flame, measure the time taken for the flame to spread on the surface of the toy
until the top of the flames first reach the top of the maximum soft-filled dimension of the toy.
If flaming occurs and the flame extinguishes before reaching the top of the maximum soft-filled dimension
of the toy, the tested toy is considered as self-extinguishing.
If the vertical distance between the point of application of the flame and the top of the soft-filled
dimension is 500 mm or more, the test can be stopped when the top of the flames reaches a height of
500 mm from the point of application of the test flame. The rate of spread of flame is then calculated using
the time elapsed to reach this point.
19
BS EN 71‑2:2020
EN 71-2:2020 (E)
Annex A
(informative)
A.1 General
This document sets safety requirements for those toys that could pose a significant risk of injury to a child
from the hazards presented by their potential to catch fire.
Several databases were consulted during the preparation of the initial standard, including those of the
United Kingdom’s ‘Home Accident Surveillance System’ and the United States’ Consumer Product Safety
Commission. There was no indication from these sources that accidents were occurring due to direct
contact of children with burning material in toys. It could be argued that the standards/legislation over
the years have resulted in safer toy products with respect to flammability.
20
BS EN 71‑2:2020
EN 71-2:2020 (E)
Attachments made from elastic or string which serve a functional purpose, for example, to secure a mask,
hat etc. on the head, or articulating a facial feature are not tested. Functional strings and elastic of this
type fit closely to the surface of the head.
In addition to the duration of flaming, 4.2.2 establishes requirements regarding the maximum burnt
length of pile or flowing elements, and 4.2.3 establishes requirements for the maximum burnt area
measured at the surface of a toy.
As the rate of spread of flame can be different depending on the direction of the fabric, preference is given
to cut the test specimen with the length corresponding to the vertical direction of the toy when in use.
Beards, moustaches, wigs, etc. made from pile or flowing elements, which protrudes 5 mm or less from
the surface of the toy, are regarded as presenting a flammability hazard similar to headdresses and have
therefore been considered as such.
The categories of toys covered by 4.2.5 are those not already covered by 4.2.1 to 4.2.4. If toys incorporate
several features e.g. hair, each part is tested to the applicable clause relevant to that particular part of the
toy.
As it is impossible to describe all types of toys in this category, Table A.1 has been provided to aid
assessments. Table A.1 is a list of (non-exhaustive) pictorial examples indicating the applicability of 4.1
to 4.2.5 and is based upon CEN/TR 15371-1:2017[7]
Table A.1 — Pictorial examples of toys and their application to 4.1 to 4.2.5
21
BS EN 71‑2:2020
EN 71-2:2020 (E)
22
BS EN 71‑2:2020
EN 71-2:2020 (E)
23
BS EN 71‑2:2020
EN 71-2:2020 (E)
24
BS EN 71‑2:2020
EN 71-2:2020 (E)
25
BS EN 71‑2:2020
EN 71-2:2020 (E)
A.4 Toy disguise costumes and toys intended to be worn by a child in play (see
4.3)
Toy disguise costumes include for example cowboy suits, nurses’ outfits and long flowing capes not
attached to headwear covered by 4.2.5. Costumes for children under the age of 12 months are not
considered to be toy disguise costumes because children of this age do not have any concept of the
character they are dressed as and so would not be able to engage in imaginative role play[6]
To ensure a wider range of testing, principally to cover small sizes of costumes etc., the test specimen
may be constructed from two pieces of the same material, either as a full-size combined test specimen or
as a half-size combined test specimen.
There are no specified dimensions for the 2 pieces of the combined test specimens but they shall have the
specified combined length (610 mm or 310 mm) and the longer piece shall be located in the lower part
of the test specimen holder so that it is ignited first. This ensures the longest uninterrupted burn before
the staples are reached by the flame front.
There are practical difficulties in preparing and testing toys that have seamed edges, edges decorated
with trims or contain filling or wadding materials. Unlike earlier versions of EN 71-2, this standard now
intentionally aims to test materials that contain features like seams, trims, appliques and similar
embellishments, provided there is sufficient material available in the test specimen. Materials that
contain wadding or fillings are also tested together with the filling/wadding provided it does not fall out
of the material when the test specimen is prepared.
Components of toy disguise costumes with loose stuffing that does fall out if prepared in accordance with
5.4.1.2 are tested as per the soft-filled toy method. This is to ensure those soft-filled parts are tested
appropriately in the form they present.
The standard also permits narrower strips of material to be tested (greater than 40 mm in width) by
allowing the test specimen to be supported on a wire mesh within the specimen holder. Narrow strips
are taken in the vertical direction and they do not include seams or other features, but they may include
any wadding or filling that remains attached to the test specimen.
Materials where there is insufficient material for a test specimen to be made, are not subject to testing
according to 5.4 but would still be assessed under general requirements of 4.1.
As it is impossible to describe all types of toys in this category, Table A.2 has been provided to aid
assessments. Table A.2 is a list of (non-exhaustive) pictorial examples indicating the applicability of 4.1,
4.3 and 5.4 and 5.5
26
BS EN 71‑2:2020
EN 71-2:2020 (E)
Table A.2 — Pictorial examples of toys and their application to 4.1, 4.3, 5.4 and 5.5
27
BS EN 71‑2:2020
EN 71-2:2020 (E)
A.7 Test relating to toy disguise costumes and toys intended to be entered by a
child (see 5.4)
Toy disguise costumes are likely to be treated as clothing articles in respect to washing therefore all toy
disguise costumes must be washed by immersion before testing irrespective of the manufacturers care
instruction. Toy disguise costumes which contain mechanisms that may be damaged by washing are still
required to undergo the immersion test as the mechanism is considered secondary to the play value of
the disguise costume itself (e.g. a battery powered sound effect inside a toy disguise costume may have a
play life span much lower than the costume itself which could be used long after the sound mechanism
ceases to function). Manufacturers are encouraged to make such mechanisms removable.
When testing a full-size sample, manufacturers may find it useful to also include marker B (for half-size
specimens). Toy disguise costumes can be complex in construction and burn at varying speeds as the flame
progresses. A specimen may burn at a steady rate initially but then reach an embellishment or trim that
may slow or speed up the overall burn. Manufacturers may find the addition of marker B helpful to select
materials and design toys with lower burn rates overall.
The U-shaped double frame test specimen holder has been designed to ensure that the material is secured
throughout the test. To facilitate the testing of narrow strips of material (<100 mm but ≥ 40 mm in width)
the addition of a wire mesh support is added to the specimen holder 2b).
When materials are subjected to heating, they react differently depending upon their type. There is a
tendency for some materials to shrink away from the flame source. By specifying the specimen holder,
this effect has been minimized and inconsistencies between the laboratories reduced. The important
criterion here is not the speed of ignition but the rate of flame spread.
A.8 Suggestions to help reduce rate of spread of flames for toy disguise costumes.
There are various design considerations that can be incorporated into the construction of toy disguise
costumes that may help reduce the rate of spread of flames in the unlikely event of accidental contact with
a source of ignition. Manufacturers are encouraged to review these aspects during the design and
development of toy disguise costumes. These may have the added benefit of avoiding the need for flame
retardant chemicals.
Design and Construction Considerations
Coatings / Finishes
• Glitter glue may increase flame progression. Heavy glitter printing around bottom edges (skirt hems,
sleeve ends etc.) may increase likelihood of ignition and/or flame progression This may occur if the
level of printing is either too light or too heavy and may relate to the levels of adhesive/glue used
rather than the glitter itself.
• Flame ignition and progression on fabric mesh/lattice may be quicker with added finishing chemicals
such as stiffeners etc.
Printing
• Large screen/plastisol prints (e.g. on the bodice of dresses) may increase flame progression.
28
BS EN 71‑2:2020
EN 71-2:2020 (E)
• When printing covers large areas consider testing of unprinted base materials as well as the printed
materials. Where printing increases flame progression, consider adding horizontal breaks to help
prevent the print carrying the flame along the fabric.
Fabrics
• Where possible it is preferable to use fabrics made entirely of synthetic fibres such as polyester and
nylon as they generally have lower rates of spread of flame than fabrics containing cellulosic fibres
such as cotton and viscose.
Costume Design
• Consider adding trim to (or just above) the hemline of heavily ruched type skirts.
• Fabric trims attached vertically to skirt hems can promote ignition and speed up flame spread. Trims
can be tested prior to selection to determine whether or not they promote ignition and rapid flame
spread. It is recommended that only trims which burn at less than 30 mm/s should be selected for
inclusion in disguise costume.
• Seams may burn faster than base materials especially skirt side seams and those on fabric
mesh/lattice overskirts. Consider a simple overlap at the waist as an alternative.
• Test specimens may burn at different rates depending upon the orientation of the warp and weft
directions. Manufacturers are advised to take this into account when designing, testing and
manufacturing costumes or testing swatches.
• Testing fabric swatches with 4.3 of this standard can be used to assess compliance of those materials.
Final article testing would then be required to ensure that the method of assembly and any trim,
seams and embellishments have not affected the compliance.
A.9 Flowcharts showing how to obtain test specimens from toy disguise costumes
The following flowcharts give guidance on how to select test specimens from disguise costumes in
accordance with 5.4.1.2. These flowcharts are for informative guidance only – the normative text must be
referred to.
29
BS EN 71‑2:2020
EN 71-2:2020 (E)
Figure A.1 — Obtaining test specimens from a material with no features, embellishments etc.
Figure A.2 — Obtaining test specimens from materials with features such as seams or
embellishments
30
BS EN 71‑2:2020
EN 71-2:2020 (E)
31
BS EN 71‑2:2020
EN 71-2:2020 (E)
Annex B
(informative)
Clause/paragraph/table/figure Change
32
BS EN 71‑2:2020
EN 71-2:2020 (E)
Clause/paragraph/table/figure Change
33
BS EN 71‑2:2020
prEN 71-2:2018 (E)
Annex ZA
(informative)
This European Standard has been prepared under a Commission’s standardization request M/445 to
provide one voluntary means of conforming to essential requirements of Directive 2009/48/EC of the
European Parliament and of the Council of 18 June 2009 on the safety of toys.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding essential requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2009/48/EC
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
34
BS EN 71‑2:2020
prEN 71-2:2018 (E)
Bibliography
[1] Directive 2009/48/EC of the European Parliament and of the Council of 18 June 2009 on the
safety of toys
[3] EN 71-4:2013, Safety of toys - Part 4: Experimental sets for chemistry and related activities
[4] REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of
16 December 2008 on classification, labelling and packaging of substances and mixtures,
amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation
(EC) No 1907/2006
[5] EN ISO 3758:2012, Textiles - Care labelling code using symbols (ISO 3758:2012)
[6] EUROPEAN COMMISSION GUIDANCE DOCUMENT NO. 17 on Carnival costumes (disguise costumes, fancy
dress). http://ec.europa.eu/growth/sectors/toys/safety/guidance_en
[7] CEN/TR 15371-1:2017, Safety of toys - Interpretations - Part 1: Replies to requests for
interpretation of EN 71-1, EN 71-2, EN 71-8 and EN 71-14
35
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
Buying standards PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
You can buy and download PDF versions of BSI publications, including British and revised or replaced.
adopted European and international standards, through our website at bsigroup.
com/shop, where hard copies can also be purchased. To find out more about becoming a BSI Subscribing Member and the benefits
of membership, please visit bsigroup.com/shop.
If you need international and foreign standards from other Standards Development
Organizations, hard copies can be ordered from our Customer Services team. With a Multi-User Network Licence (MUNL) you are able to host standards
publications on your intranet. Licences can cover as few or as many users as you
Copyright in BSI publications wish. With updates supplied as soon as they’re available, you can be sure your
documentation is current. For further information, email cservices@bsigroup.com.
All the content in BSI publications, including British Standards, is the property
of and copyrighted by BSI or some person or entity that owns copyright in the Revisions
information used (such as the international standardization bodies) and has
formally licensed such information to BSI for commercial publication and use. Our British Standards and other publications are updated by amendment or revision.
Save for the provisions below, you may not transfer, share or disseminate any We continually improve the quality of our products and services to benefit your
portion of the standard to any other person. You may not adapt, distribute, business. If you find an inaccuracy or ambiguity within a British Standard or other
commercially exploit or publicly display the standard or any portion thereof in any BSI publication please inform the Knowledge Centre.
manner whatsoever without BSI’s prior written consent.
Useful Contacts
Storing and using standards Customer Services
Standards purchased in soft copy format: Tel: +44 345 086 9001
• A British Standard purchased in soft copy format is licensed to a sole named Email: cservices@bsigroup.com
user for personal or internal company use only.
Subscriptions
• The standard may be stored on more than one device provided that it is Tel: +44 345 086 9001
accessible by the sole named user only and that only one copy is accessed at Email: subscriptions@bsigroup.com
any one time.
• A single paper copy may be printed for personal or internal company use only. Knowledge Centre
Tel: +44 20 8996 7004
Standards purchased in hard copy format: Email: knowledgecentre@bsigroup.com
• A British Standard purchased in hard copy format is for personal or internal
company use only. Copyright & Licensing
Tel: +44 20 8996 7070
• It may not be further reproduced – in any format – to create an additional copy.
This includes scanning of the document. Email: copyright@bsigroup.com
If you need more than one copy of the document, or if you wish to share the BSI Group Headquarters
document on an internal network, you can save money by choosing a subscription
product (see ‘Subscriptions’). 389 Chiswick High Road London W4 4AL UK