SECTION 2 STRUCTURE AND FUNCTION

GROUP 1 PUMP DEVICE

1. STRUCTURE
The pump device consists of main pump, regulator and gear pump.

Pi1

A3

B3

Dr P1
a4 Pi2
Qmin adjusting screw Qmax adjusting screw Qmax adjusting screw

Regulator Regulator

Pi1 Pi2

Dr
Dr B3

B1
a3

a1 a2
Front pump Port block Rear pump Gear pump

a1 A1 P1 a4 A2 a2 Port Port name Port size

A1,2 Delivery port SAE6000psi 1"

B1 Suction port SAE2500psi 3"
Dr Drain port PF 3/4 - 20
Pi1 Pi2 Power shift port
P1 (For decreasing)
PF 1/4 - 15

Pi1,i2 Pilot port PF 1/4 - 15

M
Dr a3 a1,2,3,4 Gauge port PF 1/4 - 15

B1 B3 A3 A3 Gear pump delivery port PF 1/2 - 19

B3 Gear pump suction port PF 3/4 - 20

2-1
1) MAIN PUMP(1/2)
The main pump consists of two piston pump(front & rear) and valve block.

A
789 532 548 724 792 954
732 214 531 702 534 901 719
535
808
953
886
717
406
261
824

111
774
127
710

123 251 401 211 156 157 313 312 725 314 468 141 152 113
490 212 153 158 114 124 466 885 728 151 271

111 Drive shaft(F) 271 Pump casing 719 O-ring

113 Drive shaft(R) 312 Valve block 724 O-ring
114 Spline 313 Valve plate(R) 725 O-ring
123 Roller bearing 314 Valve plate(L) 726 O-ring
124 Needle bearing 325 Casing 728 O-ring
127 Bearing spacer 401 Hexagon socket bolt 732 O-ring
141 Cylinder block 406 Hexagon socket bolt 774 Oil seal
151 Piston 466 VP Plug 789 Back up ring
152 Shoe 468 VP Plug 792 Back up ring
153 Push plate 490 VP Plug 808 Hexagon head nut
156 Bushing 531 Tilting pin 824 Snap ring
157 Cylinder spring 532 Servo piston 885 Pin
158 Spacer 534 Stopper(L) 886 Spring pin
211 Shoe plate 535 Stopper(S) 901 Eye bolt
212 Swash plate 548 Pin 953 Hexagon socket screw
214 Bushing 702 O-ring 954 Set screw
251 Support plate 710 O-ring
261 Seal cover(F) 717 O-ring

2-2
 MAIN PUMP(2/2)

544

542

543

545

541 (079)

725

466
725

325

407
VIEW A

325 Valve casing 542 Spacer 725 O-ring

407 Hexagon socket bolt 543 Stopper 1 (079) Proportional reducing valve
466 Plug 544 Stopper 2
541 Seat 545 Steel ball

2-3
2) REGULATOR(1/2)

412 875 874

755
A
897 858
B
614
612

615
613
A 611
B

A
KR3H-9N29
P2
438 Pf

801 Pi

924

641 730 643 708 644 645 646 728

SECTION B-B B

413 438

438

656
Port name port size
Pi
735 A Delivery port 1"
B Suction port 3"
Pi Pilot port PF 1/4-15
Pf Powershift port PF 1/4-15
P2 Companion delivery port -
496 724 725 436

2-4
 REGULATOR(2/2)

734 653 654 836 651 652 601 624 629 630 628
655

641 801

814 925

898

631 627

732

733
732

622

621 623 625 626 887 763 756

SECTION A-A

412 Hexagon socket screw 630 Lock Nut 732 O-ring

413 Hexagon socket screw 631 Sleeve, pf 733 O-ring
436 Hexagon socket screw 641 Pilot cover 734 O-ring
438 Hexagon socket screw 643 Pilot piston 735 O-ring
496 Plug 644 Spring seat(Q) 755 O-ring
601 Casing 645 Adjust stem(Q) 756 O-ring
611 Feed back lever 646 Pilot spring 763 O-ring
612 Lever(1) 651 Sleeve 801 Nut
613 Lever(2) 652 Spool 814 Snap ring
614 Fulcrum plug 653 Spring seat 836 Snap ring
615 Adjust plug 654 Return spring 858 Snap ring
621 Compensator piston 655 Set spring 874 Pin
622 Piston case 656 Block cover 875 Pin
623 Compensator rod 708 O-ring 887 Pin
624 Spring seat(C) 722 O-ring 897 Pin
625 Outer spring 724 O-ring 898 Pin
626 Inner spring 725 O-ring 924 Set screw
627 Adjust stem(C) 727 O-ring 925 Adjust screw(QI)
628 Adjust screw(C) 728 O-ring
629 Cover(C) 730 O-ring

2-5
 3) GEAR PUMP

700 354 351 433

434

850
311
312
355
732
307

309
710 435 361 353 310 308 434 466
725

307 Poppet 353 Drive gear 466 Plug

308 Seat 354 Driven gear 700 Ring
309 Spring seat 355 Filter 710 O-ring
310 Spring 361 Front case 725 O-ring
311 Screw 433 Flange socket 732 O-ring
312 Nut 434 Flange socket 850 Snap ring
351 Gear case 435 Flange socket

2-6
2. FUNCTION
1) MAIN PUMP
The pumps may classified roughly into the rotary group performing a rotary motion and working as
the major part of the whole pump function: the swash plate group that varies the delivery rates: and
the valve cover group that changes over oil suction and discharge.

(1) Rotary group

The rotary group consists of drive shaft
(F)(111), cylinder block(141),piston
shoes(151,152), set plate(153), spherical 124
313
bush(156), spacer(158) and cylinder 141
spring(157). The drive shaft is supported 158
151 156
by bearing(123,124) at its both ends. 152 153
The shoe is caulked to the piston to form
111
a spherical coupling. It has a pocket to 157
relieve thrust force generated by loading 123
211
pressure and to take hydraulic balance so
that it slides lightly over the shoe
plate(211). The sub group composed by
a piston and a shoe is pressed against
the shoe plate by the action of the
cylinder spring via a retainer and a
spherical bush.
Similarly, the cylinder block is pressed
against valve plate(313) by the action of
the cylinder spring.
531
(2) Swash plate group 548
The swash plate group consists of swash 214
plate(212), shoe plate(211), swash plate
support(251), tilting bush(214), tilting 212
pin(531) and servo piston(532). 251 211
The swash plate is a cylindrical part
formed on the opposite side of the sliding
surface of the shoe and is supported by
the swash support.
532 ҄
If the servo piston moves to the right and
left as hydraulic force controlled by the
regulator is admitted to hydraulic
chamber located on both sides of the ҄
servo piston, the swash plated slides over
the swash plate support via the spherical
part of the tilting pin to change the tilting
angle(ѭ ).

2-7
(3) Valve block group
The valve block group consists of valve
block(312), valve plate(313) and valve
plate pin(885).
The valve plate having two melon-shaped
ports is fixed to the valve block and feeds 312
and collects oil to and from the cylinder
block. 313
885
The oil changed over by the valve plate is
connected to an external pipeline by way
of the valve block.
Now, if the drive shaft is driven by a prime
mover(electric motor, engine, etc), it
rotates the cylinder block via a spline
linkage at the same time. If the swash
plate is tilted as in Fig(previous page) the
pistons arranged in the cylinder block
make a reciprocating motion with respect
to the cylinder block, while they revolve
with the cylinder block.
If you pay attention to a single piston, it
performs a motion away from the valve
plate(oil sucking process) within 180
degrees, and makes a motion towards
the valve plate(or oil discharging process)
in the rest of 180 degrees. When the
swash plate has a tilting angle of zero,
the piston makes no stroke and
discharges no oil.

2-8
2) REGULATOR
Regulator consists of the negative flow control, total horse power control and power shift control
function.

(1) Negative flow control

By changing the pilot pressure Pi, the
pump tilting angle(delivery flow) is
regulated arbitrarily, as shown in the
figure.
This regulator is of the negative flow

Delivery flow, Q
control in which the delivery flow Q
decreases as the pilot pressure Pi rises.
With this mechanism, when the pilot
pressure corresponding to the flow
required for the work is commanded, the
pump discharges the required flow only,
and so it does not consume the power Pilot press, Pi
uselessly.

2-9
‫ ڸ‬Flow reducing function

643 654 651 652 613 646

P1 CL
B(E)
874
897
C
A

875

611

Servo piston Small diameter

Large diameter D chamber
chamber 548
531

As the pilot pressure Pi rises, the pilot piston(643) moves to the right to a position where the
force of the pilot spring(646) balances with the hydraulic force.
The groove(A) in the pilot piston is fitted with the pin(875) that is fixed to lever 2(613). Therefore,
when the pilot piston moves, lever 2 rotates around the fulcrum of point B [fixed by the fulcrum
plug(614) and pin(875)]. Since the large hole section(C) of lever 2 contains a protruding
pin(897) fixed to the feedback lever(611), the pin(897) moves to the right as lever 2 rotates.
Since the opposing-flat section(D) of the feedback lever is fitted with the pin(548) fixed by the
tilting pin(531) that swings the swash plate, the feedback lever rotates around the fulcrum of
point D, as the pin(897) moves.
Since the feedback lever is connected with the spool(652) via the pin(874), the spool moves to
the right.
The movement of the spool causes the delivery pressure P1 to connect to port CL through the
spool and to be admitted to the large diameter section of the servo piston. The delivery
pressure P1 that is constantly admitted to the small diameter section of the servo piston moves
the servo piston to the right due to the area difference, resulting in decrease of the tilting angle.
When the servo piston moves to the right, point D also moves to the right. The spool is fitted
with the return spring(654) and is tensioned to the left at all times, and so the pin(897) is pressed
against the large hole section(C) of lever 2.
Therefore, as point D moves, the feedback lever rotates around the fulcrum of point C, and the
spool is shifted to the left. This causes the opening between the sleeve(651) and spool(652) to
close slowly, and the servo piston comes to a complete stop when it closes completely.

2-10
‫ ڹ‬Flow increasing function

643 654 651 652 613 646

P1 CL
B(E)
874
897
C

875
611

Small diameter
Servo piston D chamber
Large diameter 548
chamber
531

As the pilot pressure Pi decreases, the pilot piston(643) moves to the left by the action of the
pilot spring(646) and causes lever 2(613) to rotate around the fulcrum of point B. Since the
pin(897) is pressed against the large hole section(C) of lever 2 by the action of the return
spring(654) via the spool(652), pin(874), and feedback lever(611), the feedback lever rotates
around the fulcrum of point D as lever 2 rotates, and shifts the spool to the left. Port CL opens
a way to the tank port as the spool moves. This deprives the large diameter section of the
servo piston of pressure, and shifts the servo piston to the left by the discharge pressure P1 in
the small diameter section, resulting in an increase in the flow rate.
As the servo piston moves, point D also moves to the left, the feedback lever rotates around the
fulcrum of point C, and the spool moves to the right till the opening between the spool and
sleeve is closed.

2-11
‫ ں‬Adjustment of flow control characteristic
The flow control characteristic can be
adjusted with the adjusting screw.
Adjust it by loosening the hexagon 801
924
nut(801) and by tightening(or loosening)
the hexagonal socket head screw(924).
Tightening the screw shifts the control
chart to the right as shown in the figure.
Ɠ Adjusting values are shown in table.

Adjustment of flow control

characteristic
Speed
Tightening Flow control Flow change
amount of control change

Delivery flow, Q
adjusting starting amount
screw(924) pressure
change
amount

(min -1) (Turn) (kgf/cm2) (֤/min)

1900 +1/4 +2 +16

Pilot press, Pi

2-12
(2) Total horsepower control
The regulator decreases the pump tilting
angle(delivery flow) automatically to limit
the input torque within a certain value

Delivery flow, Q
with a rise in the delivery pressure P1 of
the self pump and the delivery pressure
P2 of the companion pump.
(The input horsepower is constant when
the speed is constant.)
Since the regulator is of the simul
Delivery press, (P1+P2)
taneous total horsepower type that
operates by the sum of load pressures of
the two pumps in the tandem double-
pump system, the prime mover is
automatically prevented from being
overloaded, irrespective of the load
condition of the two pumps, when
horsepower control is under way.
Since this regulator is of the simultaneous
total horsepower type, it controls the
tilting angles(displacement volumes) of
the two pumps to the same value as
represented by the following equation :
Tin = P1ţq/2ॏ + P2ţq/2ॏ
= (P1+P2)ţq/2ॏ
The horsepower control function is the
same as the flow control function and is
summarized in the following.(For detailed
behaviors of respective parts, refer to the
section of flow control).

2-13
‫ ڸ‬Overload preventive function

621 651 652 623 612 601 625 626

P1 CL
B(E)
897

P2 P1
875

611

Large diameter Servo piston

chamber Small diameter
D chamber

When the self pump delivery pressure P1 or the companion pump delivery pressure P2 rises, it
acts on the stepped part of the compensating piston(621). It presses the compensating
rod(623) to the right till the force of the outer spring(625) and inner spring(626) balances with
the hydraulic force. The movement of the compensating rod is transmitted to lever 1(612) via
pin(875).
Lever 1 rotates around the pin(875) (E) fixed to the casing(601).
Since the large hole section(F) of lever 1 contains a protruding pin(897) fixed to the feedback
lever(611), the feedback lever rotates around the fulcrum of point D as lever 1 rotates, and then
the spool(652) is shifted to the right. As the spool moves, the delivery pressure P1 is admitted
to the large diameter section of the servo piston via port CL, causes the servo piston move to
the right, reduces the pump delivery, flow rate, and prevents the prime mover from being
overloaded.
The movement of the servo piston is transmitted to the feedback lever via point D. Then the
feedback lever rotates around the fulcrum of point F and the spool is shifted to the left. The
spool moves till the opening between the spool(652) and sleeve(651) is closed.

2-14
‫ ڹ‬Flow reset function

621 651 652 623 612 601 625 626

P1 CL
B(E)
897

P2 P1

875

Large diameter Small diameter

chamber Servo piston D chamber

As the self pump delivery pressure P1 or the companion pump delivery pressure P2 decreases,
the compensating rod(623) is pushed back by the action of the springs(625 & 626) to rotate
lever 1(612) around point E. Rotating of lever 1 causes the feedback lever(611) to rotate
around the fulcrum of point D and then the spool(652) to move to the left. As a result, port CL
opens a way to the tank port.
This causes the servo piston to move to the left and the pump's delivery rate to increase.
The movement of the servo piston is transmitted to the spool by the action of the feedback
mechanism to move it till the opening between the spool and sleeve is closed.

2-15
‫ ں‬Low tilting angle(low flow) command preferential function
As mentioned above, flow control and horsepower control tilting angle commands are
transmitted to the feedback lever and spool via the large-hole sections(C & F) of levers 1 and 2.
However, since sections C and F have the pins(٤4) protruding from the large hole(٤8), only the
lever lessening the tilting angle contacts the pin(897) ; the hole(٤8) in the lever of a larger tilting
angle command is freed without contacting the pin(897). Such a mechanical selection method
permits preference of the lower tilting angle command of the flow control and horsepower
control.
‫ ڻ‬Adjustment of input horsepower
Since the regulator is of total cumulative horsepower type, adjust the adjusting screws of both
the front and rear pumps, when changing the horsepower set values. The pressure change
values by adjustment are based on two pumps pressurized at the same time, and the values will
be doubled when only one pump is loaded.

a. Adjustment of outer spring

Adjust it by loosening the hexagon 625 626 630 628
nut(630) and by tightening(or
loosening) the adjusting screw C(628).
Tightening the screw shifts the control 801
chart to the right and increases the
925
input horsepower as shown in the
figure. Since turning the adjusting
screw C by N turns changes the setting
of the inner spring(626), return the
adjusting screw QI(925) by NţA turns
at first.(A=2.2)
Ɠ Adjusting values are shown in table.

Adjustment of outer spring

Speed
Tightening Compens- Input torque
Delivery flow, Q

amount of ating control change

adjusting starting amount
screw(C) pressure
(924) change
amount

(min -1) (Turn) (kgf/cm2) (kgfňm)

1900 +1/4 +18 +6 Delivery press, (P1+P2)

2-16
b. Adjustment of inner spring
626
Adjust it by loosening the hexagon nut
(801) and by tightening(or loosening)
the adjusting screw QI(925).
801
Tightening the screw increases the flow
and then the input horsepower as
925
shown in the figure.
Ɠ Adjusting valves are shown in table.

Adjustment of outer spring

Speed
Tightening Compens- Input torque
amount of ating control change
adjusting starting amount
screw(QI) pressure
(925) change
amount

Delivery flow, Q
(min -1) (Turn) (kgf/cm2) (kgfňm)

1900 +1/4 +18 +4

Delivery press, (P1+P2)

2-17
(3) Power shift control

621 651 652 623 612 625 626

898 P1 CL
B(E)
897

Pf
P2 P1
875

611

Large diameter Small diameter

chamber Servo piston D chamber

The set horsepower valve is shifted by

varying the command current level of
the proportional pressure reducing valve
Delivery flow, Q

attached to the pump.

Only one proportional pressure reducing Pf=
valve is provided. MIN
Pf= .
However, the secondary pressure Pf MA
X.
(power shift pressure) is admitted to the
horsepower control section of each
pump regulator through the pump's Delivery press, (P1+P2)
internal path to shift it to the same set
horsepower level.
This function permits arbitrary setting of the pump output power, thereby providing the optimum
power level according to the operating condition.
The power shift pressure Pf controls the set horsepower of the pump to a desired level, as
shown in the figure.
As the power shift pressure Pf rises, the compensating rod(623) moves to the right via the
pin(898) and compensating piston(621).
This decreases the pump tilting angle and then the set horsepower in the same way as
explained in the overload preventive function of the hosepower control. On the contrary, the
set horsepower rises as the power shift pressure Pf falls.

2-18
(4) Adjustment of maximum and minimum flows
‫ ڸ‬Adjustment of maximum flow 808
Adjust it by loosening the hexagon
954
nut(808) and by tightening(or loosening)
the set screw(954).
The maximum flow only is adjusted
without changing other control
characteristics.

Adjustment of outer spring

Speed

Delivery flow, Q
Tightening amount Flow change
of adjusting screw amount
(953)

(min -1) (Turn) (֤/min)

1900 +1/4 -6 Delivery press, Pi

‫ ڹ‬Adjustment of minimum flow

Adjust it by loosening the hexagon
nut(808) and by tightening(or loosening)
the hexagonal socket head set screw
(953). Similarly to the adjustment of the
maximum flow, other characteristics are
not changed.
However, remember that, if tightened too
much, the required horsepower during
the maximum delivery pressure(or during
relieving) may increase.

Adjustment of outer spring

Speed
Delivery flow, Q

Tightening amount Flow change

of adjusting screw amount
(953)

(min -1) (Turn) (֤/min)

1900 +1/4 +6 Delivery press, Pi

2-19