ROJAS ELECTRICAL ENGINEERING REVIEW CENTER

2nd Floor, Yap Building, 35 M. Velez St , Barangay Guadalupe, Cebu City

DIRECTION: Shade the box on your answer sheet corresponding to 13. Which of the following circuit breakers has the lowest operating
the set of your questionnaires. Do not detach the scratch papers voltage?
from the questionnaires. Avoid unnecessary writings on your answer A. SF6 circuit breakers C. Air break circuit breakers *
sheet. GOOD LUCK! ANSWER HONESTLY! B. Air blast circuit breakers D. Minimum oil circuit breakers

EXAM DURATION: 3 hours only 14. An impedance coil takes 10 A and absorbs 250 W when
connected across a 220 V, 60 Hz source. What power will it
1. A telephone receiver has an impedance of 306 ohms at 800 Hz absorb when connected across 110 V, 25 Hz mains?
and a resistance of 60 ohms. For what value of capacitance of a A. 539 W C. 239 W
capacitor in series with the coil will the power factor be unity at B. 439 W D. 339 W *
1000 Hz?
A. 0.398 F C. 0.504 F 15. A hall 35 m x 20 m is to be provided with a general illumination
B. 0.425 F * D. 0.606 F of 130 lux. If the depreciation factor is 1.4 and the coefficient of
utilization is 0.50, determine the number of fluorescent lamp
2. Large capacity generators are invariably ____ cooled. required. Assume luminous efficiency of the fluorescent tube as
A. natural air C. nitrogen 50 lumens per watt for 80-watt lamp.
B. forced air D. hydrogen * A. 62 C. 66
B. 68 D. 64 *
3. When two resistors are connected in series the total resistance is
108 ohms. When connected in parallel the equivalent resistance 16. The capital cost on an HVDC converter is _____.
is 24 ohms. What is the value of the bigger resistance? A. less than ac substation
A. 56  C. 72  * B. more than ac substation *
B. 48  D. 81  C. same as that of ac substation
D. either B or C
4. A certain amount of fuel contains 15 x 10 10 Btu of energy. What
is the corresponding energy in kcal? 17. A direct current of 1.5 A is passed through a coil of 5000 turns
A. 3.02 x 1010 C. 3.78 x 1010 * and produces a flux of 0.1 mWb. Assuming that all the flux
B. 3.62 x 1010 D. 3.96 x 1010 threads all the turns, what would be the voltage developed
across the coil if the current were interrupted in 1 ms?
5. Which of the following is NOT a source of noise? A. 500 V * C. 750 V
A. Another communication signal * B. 333.33 V D. 133.33 V
B. Atmospheric effects
C. Manufactured electrical system 18. Reactance relay is normally preferred for protection against ___.
D. Thermal agitation in electronic components A. Earth faults only * C. phase faults only
B. internal faults only D. any type of faults
6. Determine the highest speed at which two generators mounted
on the same shaft can be driven so that the frequency of one 19. A 60 Hz, 2200-V/220 V transformer is designed to operate at a
generator is 60 Hz and the frequency of the other is 25 Hz? maximum flux density of 1 W/m2 and an induced emf of 15 volts
A. 500 rpm C. 600 rpm per turn. What is the cross sectional area of the core?
B. 300 rpm * D. 400 rpm A. 563 cm2 * C. 275 cm2
2
B. 486 cm D. 358 cm2
7. Device Number 41 is ____.
A. AC circuit breaker C. Field circuit breaker * 20. For successful parallel operation of two single-phase
B. Annunciator relay D. Alarm relay transformers, the most essential condition is that their ___.
A. percent impedances are equal
8. Two impedances, Z1 = 2 + j3 and Z2 = 3 + j6, ohms respectively B. turns ratios are exactly equal
are connected in parallel across an ac source. If the total C. polarities are properly connected *
average power drawn is 1500 W, determine total reactive power D. kVA ratings are equal
drawn.
A. 1880 VAR C. 2477 VAR * 21. A three-phase load draws a current of 10 A from a 230 V, three-
B. 2190 VAR D. 2360 VAR phase source at 88% pf lagging. What is the reactive power
drawn?
9. In which of the following power plants need the least period for A. 1288 VAR C. 1298 VAR
installation? B. 1882 VAR D. 1892 VAR *
A. Nuclear power plants C. Hydroelectric power plants
B. Thermal power plants D. Diesel engine power plants* 22. Which of the following is NOT a major benefit of FM over AM?
A. Greater efficiency C. Capture effect
10. A copper conductor with a diameter of 0.10 inch has a resistance B. Noise immunity D. Lower complexity and cost*
of 1 ohm per 1000 ft. What is the resistance of 200 ft copper
wire with a diameter of 40 mils? 23. A battery of 50 cells is being charged from a dc supply of 230 V
A. 1.25 ohms * C. 1.5 ohms and negligible internal resistance. The emf of each cell on charge
B. 1.4 ohms D. 1.35 ohms is 2.3 V, its internal resistance is 0.1 ohm and the necessary
charging current is 6 A. What extra resistance must be inserted
11. Ideal voltage source have ____. in the circuit?
A. zero internal resistance * C. infinite internal resistance A. 16.6 ohms C. 12.7 ohms
B. low value of current D. large value of emf B. 18.3 ohms D. 14.2 ohms *

12. A 60 kVA, 4800/2400 V single-phase transformer gave the 24. The armature of a dc motor running at 1200 rpm carries 45 A in
following test results: Rated voltage is applied to the low voltage current. If the back emf is 130 V, what is the torque developed
winding and the high voltage winding is open circuited. Under by the armature?
this condition, the current into the low voltage winding is 2.4 A A. 46.55 N-m * C. 55.32 N-m
and the power taken from the 2400 V source is 3456 W. A B. 39.48 N-m D. 50.85 N-m
reduced voltage of 1250 V is applied to the high voltage winding
and the low voltage winding is short circuited. Under this 25. In pumped storage plant ____.
condition, the current flowing into the voltage winding is 12.5 A A. power is produced by means of pumps
and the power taken from the 1250 V source is 4375 W. B. water is stored by pumping to high pressures
Determine the efficiency when the transformer is operating at ¾ C. water is circulated through turbines
full load, 0.80 pf lagging and a terminal voltage of 2400 volts. D. downstream water is pumped upstream during off load
A. 88.17% C. 86.37% periods *
B. 85.88% * D. 87.21%

JUST BE HONEST…… Set A / Page 1/4 …THIS IS FOR YOUR PERSONAL EVALUATION ONLY!
 ROJAS ELECTRICAL ENGINEERING REVIEW CENTER
2nd Floor, Yap Building, 35 M. Velez St , Barangay Guadalupe, Cebu City

26. A short transmission line is 20 km long. The line has a per- 38. The rotor of a 220-V, 60 Hz, 4-pole induction motor has a power
phase series impedance of 0.13 + j0.45 ohm per km. The line input of 80 kW. It is observed that the rotor emf makes 90
delivers 75 MVA, 0.80 lagging power factor at 66 kV. Determine cycles per minute. Calculate the rotor copper loss.
the sending end apparent power. A. 2 kW * C. 3 kW
A. 78.12 MVA C. 81.92 MVA B. 2.4 kW D. 1.8 kW
B. 84.97 MVA * D. 79.89 MVA
39. Multiplexing is the process of ____.
27. Two coils A and B are magnetically coupled. When connected in A. several signal sources transmitting simultaneously to a
series-aiding, the total inductance is 0.137 H, and when receiver on a common frequency
connected series opposing the total inductance is 0.085 H. B. sending the same signal over multiple channels to multiple
Calculate the value of inductance on one of the coils if the destination
coefficient of coupling is 0.242. C. transmitting multiple signals over multiple channels
A. 0.111 H C. 0.092 H D. sending multiple signals simultaneously over a single
B. 0.069 H * D. 0.049 H channel*

28. A personal communication hobby for individuals is ____. 40. A power station supplies 60 kW to a load over 2,500 ft of 000
A. ham radio * C. CB radio two-conductor copper feeder the resistance of which is 0.078
B. electronic bulletin board D. cellular radio ohm per 1000 ft. The bus bar voltage is maintained constant at
600 V. Determine the efficiency of transmission.
29. An industrial plant has an average load of 900 kW at a power A. 92% C. 93% *
factor of 0.6 lagging. A synchronous motor is to be installed to B. 95% D. 94%
drive a dc generator and to raise the overall power factor to
0.92. If preliminary estimates indicate that the input to the 41. Calculate the disk constant (in watt-hour per revolutions) of a
synchronous motor will be about 250 kW, calculate its KVA input watthour meter that makes 40 revolutions in 6 min when it is
rating. measuring a constant load of 1 kW.
A. 724 C. 772 A. 2.2 C. 2.3
B. 753 * D. 792 B. 2.4 D. 2.5 *

30. An 8-pole dc generator has a simplex wave wound armature 42. Each of the conductors in the armature of a motor is 8 in. long
containing 32 coils of 6 turns each. Its flux per pole is 0.06 Wb. and is at right angles to a magnetic field whose density is 58,000
The machine is running at 250 rpm. The induced armature lines per square inch. When the current is 230 amperes,
voltage is ____. calculate the force exerted on the wire?
A. 96 V C. 192 V A. 9.44 lbs * C. 12.28 lbs
B. 768 V D. 384 V * B. 10.17 lbs D. 11.06 lbs

31. Which of the following generating station has minimum running 43. Series capacitors can be used in distribution lines ____.
cost? A. to provide reactive power compensation *
A. Nuclear C. Thermal B. to reduce the receiving end voltage under light load condition
B. Diesel D. Hydro * C. to reduce the voltage drop
D. to reduce the line losses
32. The addition of a 20 kVAR capacitor bank improved the power
factor of a certain load to 0.90 lagging. Determine the complex 44. What should be the capacitance of a capacitor, in series with a
power before the addition of the capacitors, if the final apparent 250 ohm resistor that will limit the current to 1.2 A when the
power is 185 kVA. circuit is connected to a 600-V, 60-Hz source?
A. (156.3 + j100.6) kVA C. (166.5 + j112.3) kVA A. 5.36 F C. 7.14 F
B. (166.5 + j100.6) kVA * D. (156.3 + j112.3) kVA B. 6.12 F * D. 8.33 F

33. The isolators used in the transmission lines are capable of 45. Mho relay is normally used for the protection of ___.
breaking the _____. A. long length lines * C. medium length lines
A. fault current C. charging current * B. short length lines D. any of these
B. no load current D. load current
46. A 50-ohm distortionless transmission line has a capacitance of
34. A 40 µF capacitor is charged to store 0.2 J of energy. An 10-10 F/m. What is its inductance per meter?
unchanged 60 µF capacitor is then connected in parallel with the A. 0.25 µH * C. 500 µH
first through perfectly conducting leads. What is the energy B. 5000 pH D. 50 µH
stored on the 60 µF capacitor?
A. 0.017 J C. 0.028 J 47. It is the reserved generating capacity available for service under
B. 0.021 J D. 0.048 J * emergency conditions which is not kept in operation but in
working order.
35. Three identical coils are connected in star to a 200 volt three A. Hot reserve C. Cold reserve *
phase, 50 Hz supply and each coil takes 200 W. The pf is 0.8 B. Spinning reserve D. Firm reserve
lagging. Determine the inductance of each coil.
A. 0.102 H * C. 0.112 H 48. A two-winding transformer rated 9 kVA, 120/90-V, 60 Hz is to be
B. 0.205 H D. 0.221 H connected as an autotransformer to supply a load at 120 V from
a 210-V source. What kVA load can be supplied without
36. What are cross country faults? exceeding the current rating of the windings? Assume ideal
A. A fault occurring at any point of the power system transformer.
B. Two or more faults occurring simultaneously on the power A. 90 kVA C. 36 kVA
system * B. 25 kVA D. 21 kVA *
C. Line to line fault
D. Single line to ground fault 49. In a certain country, the energy consumption is expected to
double in how many years if the average demand growth rate is
37. A natural waterfall, 50 m high, consistently discharges 1.3 m3 5%?
per second. A mini hydroelectric plant is to be constructed at the A. 11.34 years C. 13.86 years *
bottom of the waterfalls. Estimate the electric generator kW B. 6.6 years D. 6.93 years
rating, assuming 90% mechanical to electrical conversion
efficiency and water turbine design efficiency of 70%. 50. The main benefit of light wave communications over microwaves
A. 402 * C. 409 or any other communications media is _____.
B. 406 D. 418 A. wider bandwidth * C. lower cost
B. better security D. freedom from interference

JUST BE HONEST…… Set A / Page 2/4 …THIS IS FOR YOUR PERSONAL EVALUATION ONLY!
 ROJAS ELECTRICAL ENGINEERING REVIEW CENTER
2nd Floor, Yap Building, 35 M. Velez St , Barangay Guadalupe, Cebu City

51. Two dc generators are properly connected in parallel to supply a 64. A 4-pole, 50 cycle, 3-phase induction motor has a blocked rotor
common load. The open circuit terminal voltage and internal reactance per phase that is four times the rotor resistance per
resistance of A are 240 V and 0.25  respectively; those for B phase. At what speed will the motor develop maximum torque?
are 235 V and 0.3  respectively. If the normal current rating of A. 1125 rpm * C. 1275 rpm
A is 100 A and that of B is 50 A, what total power can be B. 1200 rpm D. 1050 rpm
delivered to the load without exceeding the current rating of
either machine? 65. The load flow solution is always assured in case of ____.
A. 36.9 kW C. 31.5 kW A. Newton-Raphson method
B. 44.8 kW D. 28.6 kW * B. Gauss method
C. Gauss-Seidel method
52. An 80 F capacitor in series with a 1 kΩ resistor is connected D. None of these methods guarantees *
suddenly across a 110 V dc supply. Find the value of the current
after one time constant. 66. The positive, negative and zero sequence reactances of a 20
A. 0.25 A C. 0.058 A MVA, 13.2 kV synchronous generator are 0.3 pu, 0.2 pu and 0.1
B. 0.041 A * D. 0.11 A pu respectively. The generator is solidly grounded and is not
loaded. Neglect all resistances. Determine the fault current if a
53. For stable operation of interconnected system, the passive double line to ground fault occurs at the generator terminals b
element that can be used as interconnecting element is _____. and c.
A. reactor * C. transformer A. 5620 A C. 6250 A
B. capacitor D. resistor and capacitor B. 5180 A D. 4770 A *

54. A 3-phase, 60-Hz transposed transmission line has a flat 67. Two equal resistors A and B are connected in parallel and to a
horizontal spacing. The line reactance is 0.45  per km. The 120 V source. What potential difference exists between the
conductor geometric mean radius is 1.8 cm. Determine the midpoint of A and a point that is one-third from either end of B?
phase spacing D in meter. A. 31 V C. 20 V *
A. 5.58 m * C. 6.63 m B. 23 V D. 28 V
B. 6.27 m D. 5.87 m
68. In which of the following power plants the maintenance cost is
55. Which of the following 3-phase connections of a transformer usually high?
causes interference to the nearby communication systems? A. Nuclear power plants C. Hydroelectric power plants
A. Delta-delta C. Star-delta B. Thermal power plants * D. Diesel engine power plants
B. Star-star * D. Delta-star
69. A three-phase, Y-connected, 1385.6 V synchronous motor has a
56. Three similar coils each of resistance of 20 ohms and inductance synchronous reactance of 2 ohms and a negligible resistance.
of 0.10 H are connected in delta across a three-phase, 60 Hz, The induced emf per phase is 916.5 volts, If the motor takes an
230 V source. Determine the total power absorbed. input power of 207.84 kW, determine the motor line current.
A. 1929 W C. 643 W A. 100 A * C. 90 A
B. 1750 W * D. 583W B. 75 A D. 150 A

57. Buchholz relay is used to protect against _____. 70. A cable has the following characteristics: L = 0.2 µH/m and C =
A. rotor faults C. inter-turn faults 196.2 pF/m. The velocity of wave propagation through the cable
B. external faults D. internal faults * is _____.
A. 32 m/s C. 159.63 m/µs *
58. A 460-V series motor runs at 500 rpm taking a current of 40 A. B. 1596.3 m/s D. 0.0312 m/s
Calculate the speed if the load is reduced such that the motor is
taking 30 A. Total resistance of the armature and field circuit is 71. A three-phase line has an impedance of (2 + j4) ohms. The line
0.8 ohm. Assume flux is proportional to the field current. feeds two balanced three-phase loads that are connected in
A. 679 rpm * C. 623 rpm parallel. The first load is Y-connected and has an impedance of
B. 631 rpm D. 620 rpm (30 + j40) ohms per phase. The second load is -connected and
has an impedance of (60 – j45) ohms per phase. The line is
59. If an electrical network having one or more than one voltage energized at the sending end from a three-phase balanced
source, is transformed into equivalent electrical network with a supply of line voltage 207.85 V. Determine the line to line
single current source (which is short circuit current of previous voltage at combined loads.
circuit) with parallel internal resistance of the network with all A. 172.42 V C. 193.64 V *
current source replaced by their internal resistance. The above B. 120.42 V D. 168.25 V
illustration is called ____.
A. Thevenin’s theorem C. Reciprocity theorem 72. ACSR conductors have ___
B. Norton’s theorem * D. Superposition theorem A. all conductors made of aluminum
B. outer conductors made of aluminum *
60. A 500 kVA, 2300-volt, three-phase star connected alternator has C. inner conductors made of aluminum
a full load armature resistance drop of 50 volts and an armature D. no conductors made of aluminum
reactance drop of 500 volts per phase. Calculate the percent
regulation of the alternator at 0.8 power factor leading. 73. A constant voltage is applied to a series RL circuit by closing a
A. -10.45% C. -11.28% switch. The voltage across L is 25 V at t = 0 and drops to 5 V at
B. -12.94% D. -13.32% * t = 25 ms. If L = 2H, what must be the value of R?
A. 183.41  C. 152.63 
61. Radio signals are made up of _____. B. 162.61  D. 128.76  *
A. voltages and currents C. electrons and protons
B. electric and magnetic fields * D. noise and data 74. The circuit having the same properties in either direction is
known as ____ circuit.
62. A power plant has a maximum demand of 15 MW. The annual A. bilateral * C. unilateral
load and capacity factors are 50% and 40% respectively. B. irreversible D. reversible
Determine the installed capacity of the plant in MW.
A. 18.75 * C. 20.25 75. A single circuit, 3-phase, 60-Hz transmission line consists of
B. 21.50 D. 25.75 three conductors arranged at the corners of an equilateral
triangle spaced 5 m respectively. If the conductors each have a
63. Which of the following circuits is NOT typically part of every diameter of 0.635 cm, solve the capacitive reactance to neutral
radio transmitter? per meter.
A. Carrier oscillator C. Mixer * A. 351 ohms * C. 342 ohms
B. Driver amplifier D. Final power amplifier B. 328 ohms D. 312 ohms

JUST BE HONEST…… Set A / Page 3/4 …THIS IS FOR YOUR PERSONAL EVALUATION ONLY!
 ROJAS ELECTRICAL ENGINEERING REVIEW CENTER
2nd Floor, Yap Building, 35 M. Velez St , Barangay Guadalupe, Cebu City

76. A transmission line section shows an input impedance of 36 88. Corona loss is less when the shape of the conductor is ____.
ohms and 64 ohms respectively, when short circuited and open A. circular *
circuited. What is the characteristic impedance of the B. flat
transmission line. C. oval
A. 50 ohms C. 1.78 ohms D. none of these, since it is independent of shape
B. 7.07 ohms D. 48 ohms *
89. The positive, negative and zero sequence reactances of a 15
77. The power customer has four feeder circuits of 220 V, three- MVA, 11 kV three-phase wye-connected generator are 11%, 8%
phase. The circuits have maximum demand as follows: Circuit and 3% respectively. The neutral of the generator is solidly
no. 1 = 35 A; Circuit no. 2 = 46 A; Circuit no. 3 = 72 A; Circuit grounded. If a line to ground fault occurs on phase a of the
no. 4 = 57 A. The diversity factor is 1.5, determine the generator, solve the fault current.
maximum kVA demand with the customer. A. 13,635 A C. 10,735 A *
A. 46 C. 26.5 B. 12,105 A D. 15,294 A
B. 80 D. 53 *
90. In an ac circuit, a low value of reactive volt-ampere compared
78. Bundled conductors are used in transmission lines to ____. with watts indicates ____
A. reduced the line capacitance to ground A. high power factor * C. unity power factor
B. reduce regulation B. leading power factor D. low power factor
C. reduce the weight of the lines
D. reduce corona losses * 91. A three-phase, 60 Hz induction motor has a nameplate speed of
1720 rpm. What is the rotor frequency?
79. A 200-V dc shunt motor delivers an output of 17 kW with an A. 2.7 Hz * C. 1.8 Hz
input of 20 kW. The field winding resistance is 50  and B. 4.44 Hz D. 5 Hz
armature resistance is 0.04 . Maximum efficiency will be
obtained when the total armature copper losses are equal to __. 92. The primary disadvantage of FM is its ____.
A. 2632 W * C. 3680 W A. greater efficiency
B. 3000 W D. 5232 W B. noise susceptibility
C. excessive use of spectrum space *
80. The per unit impedance of a circuit element is 0.30. If the base D. lower efficiency
kV and MVA are halved, the new value of the per unit impedance
of the circuit element will be ____. 93. A three-phase balanced load takes a total of 6360 watts. If two
A. 0.30 C. 0.15 wattmeters are connected in the circuit to measure this power
B. 0.60 * D. 0.075 and one of them registers 2120 watts, what is the load power
factor?
81. For a lossy transmission line, the characteristic impedance does A. 0.724 C. 0.823
not depend on ___. B. 0.654 D. 0.866 *
A. the operating frequency of the line
B. the conductivity of the conductors 94. A certain voltage source causes the current to an initially
C. conductivity of the dielectric separating the conductors discharged 1000-F capacitor to increase at a rate of 0.06 A/s,
D. length of the line * determine the voltage across the capacitor after 10 s.
A. 3000 V * C. 4800 V
82. Two shunt generators A and B are to be operated in parallel to B. 600 V D. 0.6 V
supply a common load. Generator A has a no-load voltage of
240 V and a voltage of 220 V when it delivers a load of 60 A. 95. Biogas plants are suitable for ____.
Generator B has no load voltage of 230 V and a voltage of 200 V A. metallurgical industries C. commercial complexes
when it delivers the same current as A. Assume straight line B. rural areas * D. coal mines
characteristics for both machines, calculate the total load in kW
when generator B is floating. 96. The following data pertain to two alternators working in parallel
A. 10.2 kW C. 8.8 kW and supplying a total load of 80 MW. Machine 1: 40 MVA with
B. 12.4 kW D. 6.9 kW * 5% speed regulation; Machine 2: 60 MVA with 5% speed
regulation. The load sharing between machine 1 and 2
83. A 5 F capacitor is connected in series with a variable inductor respectively will be __
to a 20-V, 796 cycle source. For what value of inductance will A. 48 MW, 32 MW C. 40 MW, 40 MW
the current be 2 A lagging? B. 30 MW, 50 MW D. 32 MW, 48 MW *
A. 6 mH C. 10 mH *
B. 8 mH D. 12 mH 97. Which of the following faults is the most severe fault?
A. Single line to ground fault C. Double line to ground fault
84. A receiver-transmitter station used to increase the B. Line to line fault D. Symmetrical fault *
communication range of VHF, UHF and microwave signals is
called ____. 98. A synchronous converter delivers 500 A direct current. Assuming
A. transceiver C. repeater * 100% efficiency and unity power factor, determine the ac slip
B. remitter D. amplifier ring current if the converter has 12 rings?
A. 472 A C. 707 A
85. A group of dc motors is to operate at 220 volts at a place that is B. 236 A D. 118 A *
400 ft away from 230-volt mains. What diameter (minimum) of
copper wire is to be used in connecting the motors to the main, 99. Electromagnetic waves produced primarily by heat are called ___
if the motors take a total of 75 A? A. infrared rays * C. shortwaves
A. 0.25 in * C. 0.18 in B. microwaves D. X-rays
B. 0.32 in D. 0.20 in
100. A dc shunt generator supplies a full load current of 100 A at 110
86. Which of the following matrix is used for load flow studies? V. The shunt field resistance is 55 ohms and the stray losses are
A. Null matrix C. Unit matrix 500 W. If the efficiency at full load is 86%, find the armature
B. Y bus matrix * D. Z bus matrix resistance.
A. 0.133 ohm C. 0.103 ohm *
87. A 3-phase transmission line having a series impedance of 20 + B. 0.085 ohm D. 0.058 ohm
j30 ohms deliver 7 MW at 33 kV and 0.85 lagging power factor.
Determine percent regulation. Neglect capacitance. <end of exam>
A. 24.7% C. 21.5%
B. 20.4% D. 25.3% * AFTER THE EXAM, SUBMIT YOUR QUESTIONNAIRES AND YOUR
ANSHER SHEET. IT WILL BE RETURN TO YOU NEXT WEEK,
TOGETHER WITH YOUR SCORE AFTER CHECKING THEM…

JUST BE HONEST…… Set A / Page 4/4 …THIS IS FOR YOUR PERSONAL EVALUATION ONLY!