104-10T

PARTS BOOK
AND INSTRUCTION MANUAL
 INDEX

1. SPECIFICATIONS .............................................................................. 2
2. DESCRIPTION ................................................................................... 2
3. SPEED ................................................................................................ 2
4. TO OIL THE MACHINE ...................................................................... 3
5. NEEDLES, NIPPLE AND THREAD ................................................... 4
6. TO REMOVE, REPLACE AND SET NEEDLE AND NIPPLE ............ 5
7. TO THREAD THE MACHINE ............................................................. 7
8. LEARNING TO OPERATE THE MACHINE ....................................... 10
9. TO OPERATE THE MACHINE ........................................................... 10
10. TO REGULATE THE PRESSURE ON THE PRESSER FOOT .......... 11
11. TENSIONS .......................................................................................... 11
12. TO ADJUST THE LENGTH OF STITCH ............................................ 12
13. TO REGULATE THE PRESSURE ON THE NIPPLE ......................... 12
14. THE LOOPER ..................................................................................... 13
15. TO SET THE LOOPER ....................................................................... 14
16. TO ADJSUT THE NUMBER OF THE BRAIDING .............................. 14
17. TO ADJUST THE TENSION OF THE BRAIDING .............................. 15
18. RAY STTICH ....................................................................................... 15
19. PILE OR MOSS STITCH .................................................................... 16
20. PARTS LIST ....................................................................................... 17~

1
1. SPECIFICATIONS

Stitch specification : Single thread, chainstitch

Speed : 1500 stitches per minute
Feed : Universal feed movement
Stitch Length : Maximum 5 m/m
Presser foot lift : 7 m/m
Needle bar stroke : 14 m/m
Needle used : System 137 x 1(chainstitch)
137 *1 SM (Moss stitch)
Motor : 200W(1/4HP), Single or three phase, 4 poles, clutch

2. DESCRIPTION

Embroidery machine makes the braiding stitch and also can make the single
thread chainstitch, the tape attaching, the ray stitch and pile or moss stitch. It is
designed for ornamenting or embroidering ladies’ cloaks and suits, millinery,
uniforms, draperies, table cover, etc.

The read may be of cotton, wool, worsted, silk, metal and other threads of similar
adaptability. A large variety of fabrics can be embroidered, ranging from fine chiffon
to china silk and cloth.

The usual method of producing embroidered designs is to follow a pattern that

has been perforated, stamped or traced on the fabric, but with practice the operator
can produce embroidery designs without premarking the fabric.

3. SPEED

When first operating this machine, the best results can be obtained by running
the machine approximately 800 stitches per minute. The speed can be increased
as the operator becomes more proficient and nature of the work permits.

2
4. TO OIL THE MACHINE (Fig. 1, 2, 11 & 12)

To insure easy running and prevent unnecessary wear of the parts which are in
movable contact, the machine requires oiling.
Oil should be applied to the places designated by unlettered arrows in Fig.
1,2,11and 12.

3
 Fig. 2 shows the arm cover removed for the purpose of oiling. This arm cover can
be removed after taking out thumb screw, Fig. 10. If the machine is used
continuously, oil should be applied at least once each day.

5. NIPPLES, NIPPLES AND THREAD (Fig. 3)

Needles for embroidery machine are system 137 x 1 and are available in sizes
from 1 to 12. These needles have hooks similar in appearance to those of hand
crochet needles.

The needle must be selected according to the thickness and the style of the
thread to be used. The thread must not only fill the opening of the hook in the
needle but must slide freely therein.

To correspond with the needle used in the machine a suitable nipple must be
selected, as the needle in forming the stitch has to operate through the nipple. The

4
needle must fit in the nipple and slide freely without side play. Nipples are available
in size numbers similar to those of the needles, and for general work the number of
the nipple should be the same as that of the needle.

The nipples for embroidery machine are available in the following kinds, as per
Fig. 3.

(a) : For chainstitch and moss stitch

(b) : For tape attaching
(c) : For braiding stitch and ray stitch

6. TO REMOVE, REPLACE AND SET NEEDLE AND NIPPLE (Fig. 4)

When it is necessary to change the needle and nipple on the machine, first select
another needle and corresponding nipple. Then lower the presser foot lifter (J),
loosen screw (B) and remove needle bar (A) and needle from top of machine.
Remove nipple holder (O), loosening screw by screwdriver.

Select the correct needle hole in needle plate (D).

NOTE: The needle hole should be slightly larger than the needle, so that the

5
 needle, when laid around the needle, will have sufficient space to pass
without touching the sides of the needle hole.

Loosen thumb screw (L) and turn plate (D) until correct needle hole is in line with
needle, then tighten thumb screw (L).

Next, insert the selected nipple (N) into the lower part of nipple holder (O) and
tighten screw securely with the screwdriver, Insert the nipple holder (O) into the
nipple carrier (Fig. 3) and tighten screw securely. Screw selected needle into
needle bar (A) and tighten with pliers provided. Replace needle bar (A) down into
sleeve and adjust its height so that the fabric to be embroidered can just pass under
the point of the needle.

Be sure handle (K) is as far to the front as possible and that the hook of the
needle faces the front. Then tighten screw (B), which also should face the front.

NOTE: Do not tighten screw (B) except when needle bar (A) is in its place. If the
screw is tightened when needle bar (A) is not in its place, needle bar operating
collar is transformed and needle bar does not enter into the collar.

6
 A. Needle bar
B. Needle bar operating collar set screw
C. Presser foot slide bar thumb screw
D. Needle plate
E. Tension regulating lever
F. Tension regulating plate
G. Tension complete
H. Tension bracket
I. Tension controller spring
J. Presser foot lifter
K. Stitch rotating hand lever handle
L. Needle plate thumb screw
M. End of looper shaft
N. Nipple
O. Nipple holder
P. Nipple carrier thumb screw

7. TO THREAD THE MACHINE (Figs. 5, 6 & 7)

1) For the thread (Figs. 5 & 6)

Place the cone of thread in a convenient position on the floor.

Three thread eyelets are furnished with the machine. These eyelets should be
fastened to the underside of the table as shown at (1), (2) and (3), Fig. 5. Eyelet (1)
should be located directly above the cone of thread.

Pass the thread up from the cone and through eyelets (1), (2) and (3), then
through hole (1), over between tension discs (5), through thread controller spring
(6). Turn handle (A), Fig. 6 to the front or slightly to the left, raise presser foot and
insert threading wire (B) in the forward hole (7) of needle plate. With the left hand,
catch thread on hook of threading wire (B) and draw wire and thread up through
hole needle plate. With the left hand, hold end of thread with a slight tension.

7
 With the right hand, turn handle (A) straight to the left, having started the
machine, quickly bear down and up on handle (A) so the needle will pick up the
thread for one stitch. Keep handle (A) in same position and with the threading wire
(B), draw thread directly toward you, laying end of thread loosely on needle plate
after t comes up thread needle hole.

2) For the cord (Fig. 7)

Wind the cord on the cord spool , using the spool winder spindle on the
pulley. Place it on the cord spool bracket . Inter the cord into the top of needle
bar with the threading wire (large) and pass it below the end of nipple
carrier 6, then through to the hole of the nipple .

3) For the braid (Fig. 7)

Wind the braid on the braid spool , using the spool winder spindle on the
pulley. Place it on the braid spool bracket . Pass the braid through the braid
guide of the bracket and through the hole of the braid leader rod and
the hole of the braid leader bracket, then through the forward hole of the
braid leader guide.

Now the machine is ready for operation.

8
9
8. LEARNING TO OPERATE THE MACHINE (Fig.8)

Note: When in operation the machine pulley must always turn over away from
operator.

Mark a design (see Fig.8) on 30cm (12 inch) square piece of cloth. Place cloth
under presser foot so that the needle will enter cloth as at point 1. Turn handle ,
Fig. 6 to the right and the hook of the needle will be turned in the same direction.
Lower presser foot, start machine pulley by turning it over away from you, grasp
handle and pull it down to start the machine. With handle pressed and to the
right, cloth will be fed to point , then turn handle to the front and cloth will be fed
to point turn handle to the left and cloth will be fed to point etc.

To stop machine raise handle . Machine will stop with needle as its highest
point.

9. TO OPERATE THE MACHINE (Fig. 9)

The operator should practice embroidering designs similar to those illustrated

below.

These designs can be sketched on white material such as lawn, and by following
them, the operator can soon become proficient enough to attempt more intricate
designs or patterns.

10
10. TO REGULATE THE PRESSURE ON THE PRESSER FOOT (Fig.4)

The pressure on the presser foot is regulated by the thumb screw , Fig.4. To
increase the pressure, turn the thumb screw over to the right or downward. To
decrease the pressure, turn the thumb screw over to the left or upward.

11. TENSIONS (Fig.5)

If stitches are too tight, raise needle bar approximately 1.5 m/m (1/16 inch).

Various effects can be produced by changing the height of the needle bar as well
as by adjusting the length of stitch.

The tension on the thread is regulated by the thumb nut , Fig. 5 at the left of
the tension discs. To increase the tension turn this nut over toward you. To
decrease the tension turn this nut over from you . this tension should be only tight
enough to prevent the skipping of stitch.

11
12. TO ADJUST THE LENGTH OF STITCH (Fig. 10)

The length of stitch is adjusted by screw , Fig. 10. To lengthen the stitch,
loosen locking lever and turn screw over to the left or upward, then tighten
locking lever .

To shorten the stitch, loosen locking lever and turn the screw over to the
right or downward, then tighten locking lever .

13. TO REGULATE THE PRESSURE ON THE NIPPLE (Fig.10 & 11)

The pressure on the nipple is regulated by the thumb screw , Fig. 10 at the top
of the machine. To increase the pressure, turn this thumb screw over to the right or
downward. To decrease the pressure, turn this thumb screw over to the left or
upward.

Note: Too much pressure on the nipple may cause the thread to break.

When sewing fine net, it is sometimes necessary to prevent the nipple from
touching the needle plate.

12
 To raise the nipple, insert a screwdriver in hole , Fig. 11 and loosen the set
screw therein. The eccentric adjusting stud can then be turned by the wrench
provided so that nipple can be set at desired height, then tighten the set screw in
hole .

14. THE LOOPER (Fig. 12)

Allow the stop motion to throw the machine out of action and make sure that it is
securely held in its looking position. Raise the needle holder to avoid breaking the
point of the needle, remove the needle plate after removing the thumb screw ,
Fig. 12, and observe the notch in the looper which, when in its correct position,
should be at the rear slightly to the right of the needle, while the handle is
toward the front.

13
15. TO SET THE LOOPER (Fig. 4 & 12)

Turn the machine back on its hinges and turn handle , Fig. 12 and screw ,
Fig. 4 to the front. Loosen set screw , Fig. 12 of the operating worm gear .
And turn the gear slightly, until the notch in the looper is in its correct position as
instructed above. After having set the worm gear flush with the end of the looper
shaft , tighten the set screw .

16. TO ADJUST THE NUMBER OF THE BRAIDING (Fig. 10)

The number of the braiding can be adjusted by the lever , Fig. 10, which is
located on the top of the machine frame. At the number 0, the gears do not engage
and the machine will be operated as chainstitch, moss stitch or tape attaching
embroidery.

In case of the number 1, one braiding (roll) per one stitch

In case of the number 2, 1/2 braiding (roll) per one stitch
In case of the number 3, 1/3 braiding (roll) per one stitch
In case of the number 4, 1/4 braiding (roll) per one stitch

The bigger the number is set, the coarser the internal of the braiding will be.
Therefore, set the number 1 for normal braiding stitch.

14
 Note: Do not change the lever while the clutch is engaging. If do so, it may cause
the machine to damage.

17. TO ADJSUT THE TENSION OF THE BRAIDING (Fig. 10)

It is the best for the normal braiding embroidery works that the braid spool
bracket , Fig. 10 is set in the left while the handle is at the front.

To adjust as above, bring the handle to front, hold the handle by the knee as
it does not turn round, then press the gear changing lever , Fig. 10 to right and
turn the braid spool bracket to the above position.

To increase the tension of the braiding, turn the braid spool bracket over from
you. To decrease the tension to the braiding, turn the braid spool bracket over
toward you.

If the gears do not engage after the above adjustment, hold the braid spool
bracket by the left hand and turn the pulley by the right hand.

Note: Do not press the gear changing lever while the clutch is engaging. If
do so , it may cause the machine to damage.

The additional adjustment will be made by the braid spool adjusting thumb nut
, Fig. 7 and the braid leader guide , Fig. 10.

18. RAY STITCH (Fig. 4 & 7)

The ray stitch can be done by adjusting the tensions of the thread loose, the
tensions of the cord and the braid slightly tight as you like.

(1) For loosening thread (Fig. 4)

Loosen the screw , Fig. 4 and lift the needle bar so that the thread

15
 loosens.

(2) For tightening cord (Fig. 7)

Tighten the screw , Fig. 7 so that the rotation of the cord spool becomes
slow.

(3) For tightening braid (Fig. 7)

Tighten the screw , Fig. 7 so that the rotation of the braid spool becomes
slow.

Then, set the lever , Fig. 10 to the number 1.

19. PILE OR MOSS STITCH (Fig. 4, 10 & 12)

The raised pile or moss stitch is produced by adjusting the machine so that it will
drop the stitches in loose loops on the materials. To accomplish this, turn handle (K),
Fig. 4 to the front, loosen the screw (B) and turn the needle bar (A) so that the hook
of the needle will point directly to the back of the machine, then tighten the screw
(B). Reach under the bed of the machine with the left hand, grasp the knurled end
, Fig. 12 of the operating worm gear draw the worm gear to the left and while
holding it turn handle around to the right directly to the back, then release the
knurled end of the gear.

The looper will then be set in the opposite direction to that which is required for
the chain stitch, or with the notch of the looper at the front of the needle while
handle , Fig. 10 is at the front. Change the presser foot to the presser foot
(spur).

By operating the machine and turn handle rapidly, so as to make very small
circles of dropped stitch loops laid one on the other, raised pile work is produced.
The higher the needle is set the longer the loop will be. The size of the thread and
thickness of the material used will have to be considered when adjusting the
machine for pile stitching.

16
1. MACHINE FRAME & COVERS COMPONENTS

17
REF. NO. PARTS NO. DESCRIPTION
P1-1 AM1114-10 MACHINE FRAME
P1-2 8181 ARM TOP SCREW
P1-3 8470 ARM HEAD COVER
P1-4 5227 ARM HEAD COVER THUMB SCREW
P1-5 8466-A SPOOL CARRIER DRIVING GEAR COVER
P1-6 4015 SPOOL CARRIER DEIVING GEAR COVER SET SCREW
P1-7 8434 ARM SIDE COVER
P1-8 8150 ARM SIDE COVER POSITION PIN
P1-9 8483 ARM SIDE COVER THUMB SCREW
P1-10 S-8445 CORD SPOOL BRACKET SUPPORTING ARM WITH NEEDLE BEARING
P1-11 8172 CORD SPOOL BRACKET SUPPORTING ARM CLAMP SCREW
P1-12 8146 CORD SPOOL BRACKET SUPPORTING ARM POSITION PIN

18
3. ARM SHAFT MECHANISM COMPONENTS

19
REF. NO. PARTS NO. DESCRIPTION
P3-1 8403 ARM SHAFT BUHSING
P3-2 98-A ARM SHAFT BUSHING SET SCREW
P3-3 8404 DRIVING PULLEY SLEEVE BUSHING
P3-4 131 DRIVING PULLEY SLEEVE BUSHING SET SCREW
P3-5 8406 ARM SHAFT GEAR SLIDING KEY
P3-6 8407 ARM SHAFT GEAR SLIDING KEY SPRING
P3-7 824 ARM SHAFT ASSEMBLY WITH REF. NOS. 8-10
P3-8 8008 STOP CAM
P3-9 8163-B STOP CAM DRIVING STUD
P3-10 8005-A NEEDLE DRIVING CAM POSITION SCREW
P3-11 8006 NEEDLE DRIVING CAM ROLLER
P3-12 5266 ARM SHAFT COLLAR
P3-13 132-C ARM SHAFT COLLAR SET SCREW
P3-14 8405 ARM SHAFT GROOVED COLLAR
P3-15 8480-A ARM SHAFT GROOVED COLLAR SET SCREW
P3-16 8408 ARM SHAFT GEAR (NO.1)
P3-17 8412 ARM SHAFT GEAR WASHER
P3-18 8409 ARM SHAFT GEAR (NO.2)
P3-19 8410 ARM SHAFT GEAR (NO.3)
P3-20 8411 ARM SHAFT GEAR (NO.4)
P3-21 8009-A STOP CAM SPRING
P3-22 8010 STOP CAM SPRING COLLAR
P3-23 132 STOP CAM SPRING COLLAR SET SCREW
P3-24 8012 ARM SHAFT DRIVING FLANGE
P3-25 8013 ARM SHAFT DRIVING FLANGE POSITION SCREW
P3-26 8014 ARM SHAFT DRIVING FLANGE SET SCREW
P3-27 8017-B DRIVING PULLEY
P3-28 8015 DRIVING PULLEY SLEEVE
P3-29 8018 DRIVING PULLEY SLEEVE SCREW

20
5. ARM HEAD PARTS COMPONENTS (NO.1)

21
REF. NO. PARTS NO. DESCRIPTION
P5-1 8472 ARM HEAD
P5-2 8020 ARM HEAD SCREW (UPPER) (LONG)
P5-3 8021 ARM HEAD SCREW (UPPER) (SHORT)
P5-4 8022 ARM HEAD SCREW (LOWER)
P5-5 8150 ARM HEAD POSITION PIN
P5-6 8145 ARM HEAD POSITION PIN
P5-7 S-8462 SPOOL CARRIER DRIVING GEAR GUIDE WITH REF. NO.8
P5-8 11152 SPOOL CARRIER DRIVING GEAR GUIDE SCREW
P5-9 4031 SPOOL CARRIER DRIVING GEAR GUIDE SET SCREW
P5-10 8474 SPOOL CARRIER DRIVING GEAR COVER BRACKET
P5-11 4015 SPOOL CARRIER DRIVING GEAR COVER BRACKET SET SCREW
P5-12 8452-A NIPPLE CARRIER SLEEVE WITH SCREWS
P5-13 8465 NIPPLE CARRIER SLEEVE BUSHING
P5-14 8464 SPOOL CARRIER DRIVING GEAR
P5-15 8461 SPOOL CARRIER DRIVING IDLER GEAR
P5-16 8475-C SPOOL CARRIER DRIVING IDLER GEAR STUD
P5-17 2553-A SPOOL CARRIER DRIVING IDLER GEAR STUD SET SCREW
P5-18 8463 SPOOL CARRIER IDLER GEAR SUPPORTING BLOCK
P5-19 113-A SPOOL CARRIER IDLER GEAR SUPPORTING BLOCK SET SCREW
P5-20 8320-A NIPPLE HOLDER
P5-21 8339 NIPPLE HOLDER SET SCREW
P5-22 8498-A-3 NIPPLE (FOR BRAIDING)
P5-23 8335 NIPPLE SET SCREW
P5-24 8510-AA NEEDLE BAR
P5-25 8027-3 NEEDLE (137*1 #3)
P5-26 8449 ARM HEAD SLEEVE
P5-27 831 NEEDLE BAR GUIDE BLOCK & COLLAR WITH REF. NOS. 28-29
P5-28 8477 NEEDLE BAR GUIDE BLOCK SET SCREW (LARGE)
P5-29 8476 NEEDLE BAR GUIDE BLOCK SET SCREW (SMALL)
P5-30 8308 ARM HEAD SLEEVE CAP
P5-31 5176-A ARM HEAD SLEEVE CAP SCREW
P5-32 8030 ARM HEAD SLEEVE GEAR
P5-33 129-B ARM HEAD SLEEVE GEAR SET SCREW
P5-34 S-8456 FEED ROTATING SHAFT & GEAR
P5-35 8311 FEED SLIDE BLOCK
P5-36 8312 FEED LEVER
P5-37 8314 FEED LEVER HINGE PIN
P5-38 8313 FEED LEVER BRACKET
P5-39 124 FEED LEVER BRACKET SET SCREW
P5-40 8335 FEED LEVER BRACKET SET SCREW
P5-41 8037 FEED RECOVERING SPRING (RIGHT)
P5-42 8036 FEED RECOVERING SPRING (LEFT)
P5-43 8038 FEED RECOVERING SPRING SCREW

22
7. ARM HEAD PARTS COMPONENTS (NO.2)

23
REF. NO. PARTS NO. DESCRIPTION
P7-1 8067 PRESSER FOOT SLIDE BAR THUMB SCREW
P7-2 8161 PRESSER FOOT SLIDE BAR THUMB SCREW NUT
P7-3 8065 PRESSER FOOT SLIDE BAR SPRING
P7-4 8066 PRESSER FOOT SLIDE BAR SPRING PLUNGER
P7-5 8322-A PRESSER FOOT SLIDE BAR
P7-6 8139 PRESSER FOOT SLIDE BAR ADJUSTING SCREW
P7-7 8063 PRESSER FOOT SLIDE BAR GUIDE
P7-8 8138 PRESSER FOOT SLIDE BAR GUIDE SET SCREW
P7-9 8064 PRESSER FOOT SLIDE BAR SPRING STOP
P7-10 8140 PRESSER FOOT SLIDE BAR SPRING STOP SCREW
P7-11 8069-A PRESSER FOOT LEVER SWIVEL
P7-12 8188 PRESSER FOOT LEVER SWIVEL STOP SCREW
P7-13 8070-A PRESSER FOOT LEVER SWIVEL HINGE SCREW
P7-14 S-8453 PRESSER FOOT LEVER
P7-15 8072 PRESSER FOOT CLAMP
P7-16 8481-A PRESSER FOOT CLAMP THUMB SCREW
P7-17 8454-A PRESSER FOOT
P7-18 8073-B PRESSER FOOT SHOE (RUBBER)
P7-19 8315 FEED LEVER BRACKET GUIDE
P7-20 8316 FEED LEVER BRACKET GUIDE CAP
P7-21 8136 FEED LEVER BRACKET GUIDE CAP SCREW
P7-22 8310-A FEED SLIDE BAR
P7-23 8428 FEED SLIDE BAR BLOCK
P7-24 4173 FEED SLIDE BAR BLOCK SET SCREW
P7-25 8317 NIPPLE CARRIER
P7-26 8051 NIPPLE CARRIER LIFTING SCREW STUD
P7-27 8055 NIPPLE CARRIER GUIDE
P7-28 8182 NIPPLE CARRIER GUIDE SCREW
P7-29 8054 NIPPLE CARRIER THUMB SCREW
P7-30 8160 NIPPLE CARRIER THUMB SCREW NUT
P7-31 8052 NIPPLE CARRIER SPRING
P7-32 8053 NIPPLE CARRIER EXTENSION
P7-33 8047 FEED REGULATING SCREW
P7-34 8048 FEED REGULATING SCREW LOCK LEVER NUT

24
9. ARM HEAD PARTS (NO.3), BRAID LEADER & SPOOL CARRIER
COMPONENTS

25
REF. NO. PARTS NO. DESCRIPTION
P9-1 8042 FEED BELL CRANK
P9-2 8044 FEED BELL CRANK ROLLER
P9-3 8045 FEED BELL CRANK ROLLER SCREW
P9-4 8046 FEED BELL CRANK SPRING
P9-5 8043 FEED BELL CRANK HINGE STUD
P9-6 5225-C FEED BELL CRANK HINGE STUD SET SCREW
P9-7 8057 NIPPLE CARRIER BELL CRANK
P9-8 8455 NIPPLE CARRIER BELL CRANK HINGE STUD
P9-9 5225-C NIPPLE CARRIER BELL CRANK HINGE STUD SET SCREW
P9-10 8059 PRESSER FOOT SLIDE BELL CRANK
P9-11 8455 PRESSER FOOT SLIDE BELL CRANK HINGE STUD
P9-12 5225-C PRESSER FOOT SLIDE BELL CRANK HINGE STUD SET SCREW
P9-13 8060-A PRESSER FOOT LIFTER
P9-14 8061 PRESSER FOOT LIFTER HINGE SCREW
P9-15 8304 NEEDLE BAR OPERATING SLIDE
P9-16 827 BRAID LEADER ASSEMBLY WITH REF. NOS.17-18
P9-17 827-1 BRAID LEADER GUIDE
P9-18 4185 BRAID LEADER GUIDE SET SCREW
P9-19 8484 BRAID LEADER THUMB SCREW
P9-20 826 SPOOL CARRIER ASSEMBLY
P9-21 124 SPOOL CARRIER SET SCREW
P9-22 8467 BRAID SPOOL (METAL)

26
11. GEAR CHANGE LEVER, SPOOL CARRIER DISENGAGING
LEVER & INTERMEDIATE GEAR PARTS COMPONENTS

27
REF. NO. PARTS NO. DESCRIPTION
P11-1 8439 GEAR CHANGE LEVER COVER
P11-2 8440 GEAR CHANGE LEVER COVER SET SCREW
P11-3 8441 GEAR CHANGE GRADUATED PLATE
P11-4 8435 GEAR CHANGE LEVER BASE
P11-5 113-B GEAR CHANGE LEVER BASE SET SCREW
P11-6 8437-1 GEAR CHANGE LEVER
P11-7 8437-2 GEAR CHANGE LEVER SPRING
P11-8 8437-3 GEAR CHANGE LEVER BALL
P11-9 8438 GEAR CHANGE LEVER SET SCREW
P11-10 8490 SPOOL CARRIER DISENGAGING LEVER
P11-11 5162-B SPOOL CARRIER DISENGAGING LEVER SPRING
P11-12 4105 SPOOL CARRIER DISENGAGING LEVER SPRING SCREW
P11-13 8488 SPOOL CARRIER DISENGAGING LEVER BRACKET
P11-14 8491 SPOOL CARRIER DISENGAGING LEVER BRACKET SET SCREW
P11-15 8489 SPOOL CARRIER DISENGAGING LEVER STUD
P11-16 5207 SPOOL CARRIER DISENGAGING LEVER STUD NUT
P11-16' 8514 SPOOL CARRIER DISENGAGING LEVER COVER
P11-17 8416 INTERMEDIATE GEAR (NO.1)
P11-18 129-B INTERMEDIATE GEAR SET SCREW
P11-19 S-8417 INTERMEDIATE GEAR ASSEMBLY (NO. 2-4)
P11-20 129-A INTERMEDIATE GEAR SET SCREW
P11-21 8415 INTERMEDIATE GEAR SHAFT
P11-22 8414 INTERMEDIATE GEAR BRACKET
P11-23 114-B INTERMEDIATE GEAR BRACKET SET SCREW
P11-24 8146 INTERMEDIATE GEAR BRACKET POSITION PIN

28
13. FEED ROTATING GEAR & STOP BRACKET PARTS
COMPONENTS

29
REF. NO. PARTS NO. DESCRIPTION
P13-1 8424 FEED ROTATING SHAFT BRACKET
P13-2 113-A FEED ROTATING SHAFT BRACKET SET SCREW
P13-3 8146 FEED ROTATING SHAFT BRACKET POSITION PIN
P13-4 8423-A FEED ROTATING GEAR (REAR)
P13-5 8142 FEED ROTATING GEAR SET SCREW
P13-6 8420 STITCH ROTATING SHAFT
P13-7 8422-A STITCH ROTATING GEAR (UPPER)
P13-8 8142 STITCH ROTATING GEAR SET SCREW
P13-9 8112-B STITCH ROTATING GEAR (LOWER)
P13-10 821 STOP BRACKET ASSEMBLY (REF. NOS.11-23)
P13-11 8442 STOP BRACKET
P13-12 8079 STOP BRACKET INTERLOCKING ROD
P13-13 8486 STOP BRACKET INTERLOCKING ROD SPRING
P13-14 8081 STOP BRACKET INTERLOCKING STOP BLOCK
P13-15 121 STOP BRACKET INTERLOCKING STOP BLOCK SCREW
P13-16 8443 STARTING TRIP LEVER SLIDE
P13-17 8083 STARTING TRIP LEVER SLIDE CAP
P13-18 124 STARTING TRIP LEVER SLIDE CAP SCREW
P13-19 8084 STARTING TRIP LEVER SLIDE SPRING
P13-20 8077 STOP CAM ROLLER
P13-21 8078 STOP CAM ROLLER SCREW STUD
P13-22 8075 STOP CAM ROCKING LEVER
P13-23 8076 STOP CAM ROCKING LEVER HINGE SCREW
P13-24 8473 STOP BRACKET SET SCREW (LONG)
P13-25 8172 STOP BRACKET SCREW (SHORT)
P13-26 8159 STOP BRACKET POSITION PIN

30
15. FEED ROTATING SHAFT MECHANISM COMPONENTS

31
REF. NO. PARTS NO. DESCRIPTION
P15-1 8110-A SPOOL CARRIER GEAR DRIVING BEVEL GEAR
P15-2 8142 SPOOL CARRIER GEAR DRIVING BEVEL GEAR SET SCREW
P15-3 8458 SPOOL CARRIER GEAR DRIVING GEAR SHAFT
P15-4 8459 SPOOL CARRIER GEAR DRIVING GEAR SHAFT BUSHING
P15-5 4078 SPOOL CARRIER GEAR DRIVING GEAR SHAFT BUSHING SET SCREW
P15-6 8460 SPOOL CARRIER GEAR DRIVING GEAR
P15-7 129-A SPOOL CARRIER GEAR DRIVING GEAR SET SCREW
P15-8 8097-A SPOOL CARRIER GEAR DRIVING BEVEL GEAR
P15-9 129-B SPOOL CARRIER GEAR DRIVING BEVEL GEAR SET SCREW
P15-10 8457 SPOOL CARRIER GEAR DRIVING BEVEL GEAR SLEEVE
P15-11 8097 SPOOL CARRIER GEAR DRIVING BEVEL GEAR
P15-12 8142 SPOOL CARRIER GEAR DRIVING BEVEL GEAR SET SCREW
P15-13 8427 SPOOL CARRIER GEAR DRIVING BEVEL GEAR
P15-14 8496 SPOOL CARRIER GEAR DRIVING BEVEL GEAR SET SCREW
P15-15 8429 SPOOL CARRIER GEAR DRIVING BEVEL GEAR BRACKET
P15-16 8146 SPOOL CARRIER GEAR DRIVING BEVEL GEAR BRACKET TAPER PIN
P15-17 8495 SPOOL CARRIER GEAR DRIVING BEVEL GEAR BRACKET WASHER
P15-18 S-8425 SPOOL CARRIER GEAR DRIVING SLEEVE GEAR ASSEMBLY
P15-19 8492-T SPOOL CARRIER GEAR DRIVING SLEEVE GEAR SPRING
P15-20 8504 SPOOL CARRIER GEAR DRIVING SLEEVE GEAR THRUST BEARING
P15-21 8433 FEED ROTATING SHAFT GEAR (SMALL)
P15-22 129-B FEED ROTATING SHAFT GEAR SET SCREW
P15-23 8432 FEED ROTATING SHAFT GEAR (LARGE)
P15-24 8431 FEED ROTATING SHAFT BLOCK
P15-25 8479 FEED ROTATING SHAFT BLOCK SET SCREW
P15-26 8430 FEED ROTATING SHAFT BLOCK PIN
P15-27 5262 FEED ROTATING SHFAT BLOCK PIN SET SCREW
P15-28 10017-A FEED ROTATING SHAFT COLLAR
P15-29 8142 FEED ROTATING SHAFT COLLAR SET SCREW
P15-30 8421 FEED ROTATING SHAFT

32
17. LOOPER OPERATING MECHANISM COMPONENTS

33
P17-12 8099 LOOPER BRACKET
P17-13 8152 LOOPER COLLAR
P17-14 129-B LOOPER COLLAR SET SCREW
P17-15 8158 LOOPER BRACKET SET SCREW
P17-16 8150 LOOPER BRACKET POSITION PIN
P17-17 822 LOOPER OPERATING CONNECTION ASSEMBLY (REF. NOS. 18-28)
P17-18 S-8444 LOOPER OPERATING CONNECTION
P17-19 8174 LOOPER OPERATING CONNECTION JOINT PITMAN
P17-20 8175 LOOPER OPERATING CONNECTION JOINT PITMAN NUT (UPPER)
P17-21 8176 LOOPER OPERATING CONNECTION JOINT PITMAN NUT (LOWER)
P17-22 8177 LOOPER OPERATING CONNECTION JOINT
P17-23 8178 LOOPER OPERATING CONNECTION JOINT HINGE STUD
P17-24 8179 LOOPER OPERATING CONNECTION JOINT HINGE STUD
SPRING WASHER
P17-25 5207 LOOPER OPERATING CONNECTION JOINT HINGE STUD NUT
P17-26 8089-A LOOPER OPERATING BELL CRANK
P17-27 8092 LOOPER OPERATING BELL CRANK HINGE BLOCK
P17-28 8093 LOOPER OPERATING BELL CRANK HINGE BLOCK SCREW
P17-29 8090 LOOPER OPERATING BELL CRANK HINGE SCREW
P17-30 8091 LOOPER OPERATING BELL CRANK HINGE SCREW NUT
P17-31 8088 LOOPER OPERATING BELL CRANK BRACKET
P17-32 8143 LOOPER OPERATING BELL CRANK BRACKET SET SCREW
P17-33 8149 LOOPER OPERATING BELL CRANK BRACKET POSITION PIN
P17-34 8094 LOOPER OPERATING SHAFT
P17-35 8097-A LOOPER OPERATING SHAFT BEVEL GEAR (LEFT)
P17-36 8142 LOOPER OPERATING SHAFT BEVEL GEAR SET SCREW
P17-37 8096-A LOOPER OPERATING SHAFT BEVEL GEAR (RIGHT)
P17-38 8095-B LOOPER OPERATING SHAFT SLEEVE
P17-39 8098-B LOOPER OPERATING SHAFT GUIDE BLOCK
P17-40 129-B LOOPER OPERATING SHAFT GUIDE BLOCK SET SCREW

34
19. TENSION REGULATING PARTS & STITCH ROTATING HAND
LEVER PARTS COMPONENTS

35
REF. NO. PARTS NO. DESCRIPTION
P19-1 811 TENSION BRACKET ASSEMBLY (REF. NOS. 2-17)
P19-2 8127 TENSION REGULATING PLATE
P19-3 8128 TENSION REGULATING PLATE HINGE SCREW
P19-4 8129-A TENSION REGULATING SPRING
P19-5 8130-A TENSION REGULATING SPRING SCREW STUD
P19-6 8125 TENSION BRACKET
P19-7 8131 TENSION REGULATING LEVER
P19-8 8132-A TENSION REGULATING LEVER HINGE SCREW
P19-9 4140-A TENSION REGULATING LEVER HINGE SCREW SPRING WASHER
P19-10 8133-A THREAD CONTROLLER SPRING
P19-11 121 THREAD CONTROLLER SPRING SCREW
P19-12 810 TENSION ASSEMBLY (REF. NOS.13-17)
P19-13 81 TENSION THUMB NUT
P19-14 5267-A TENSION SPRING
P19-15 5190-A TENSION DISC
P19-16 8164 TENSION STUD
P19-17 8207 TENSION STUD NUT
P19-18 8143 TENSION BRACKET SET SCREW
P19-19 8117 STITCH ROTATING GEAR BRACKET SHAFT (INTERMEDIATE)
P19-20 8110-A STITCH ROTATING GEAR BRACKET SHAFT GEAR
P19-21 8142 STITCH ROTATING GEAR BRACKET SHAFT GEAR SET SCREW
P19-22 8114-A STITCH ROTATING HAND LEVER SHAFT
P19-23 8096-A STITCH ROTATING HAND LEVER SHAFT GEAR
P19-24 8142 STITCH ROTATING HAND LEVER SHAFT GEAR SET SCREW
P19-25 8113 STITCH ROTATING GEAR BRACKET
P19-26 8143 STITCH ROTATING GEAR BRACKET SET SCREW
P19-27 8149 STITCH ROTATING GEAR BRACKET POSITION PIN
P19-28 8122 STARTING TRIP LEVER ROD
P19-29 8123 STARTING TRIP LEVER (INTERMEDIATE)
P19-30 8124 STARTING TRIP LEVER HINGE SCREW
P19-31 808 STITCH ROTATING HAND LEVER HANDLE ASSEMBLY
(REF. NOS.31-40)
P19-32 8119 STARTING TRIP LEVER
P19-33 8045 STARTING TRIP LEVER HINGE SCREW
P19-34 8120 STARTING TRIP LEVER BLOCK
P19-35 8121 STARTING TRIP LEVER BLOCK SCREW STUD
P19-36 S-8115-A STITCH ROTATING HAND LEVER WITH PIN & SCREW
P19-37 5176-A STITCH ROTATING HAND LEVER SET SCREW
P19-38 8118 STITCH ROTATING HADN LEVER HANDLE
P19-39 8116 STITCH ROTATING HAND LEVER HANDLE SLEEVE
P19-40 5070 STITCH ROTATING HAND LEVER HANDLE SLEEVE WASHER
P19-41 8141 STITCH ROTATING HAND LEVER HANDLE SLEEVE SCREW

36
21. CORD SPOOL & BELT COVER COMPONENTS

37
 REF. NO. PARTS NO. DESCRIPTION
P21-1 8336 CORD SPOOL
P21-2 8331 CORD SPOOL SPINDLE
P21-3 7012-A CORD SPOOL SPINDLE WASHER
P21-4 8332 CORD SPOOL SPINDLE THUMB NUT
P21-5 8487 CORD SPOOL BRACKET
P21-6 8329 CORD SPOOL FRICTION SPRING
P21-7 8140 CORD SPOOL FRICTION SPRING SCREW
P21-8 4356 CORD SPOOL FRICTION SPRING ADJUSTING SCREW
P21-9 8448 CORD SPOOL BRACKET SLEEVE WITH SCREWS
P21-10 98 CORD SPOOL BRACKET SLEEVE SET SCREW
P21-11 8446 CORD SPOOL BRACKET SLEEVE THRUST BEARING
※ P21-12 830 BELT COVER ASSEMBLY (REF. NOS.12-19)
※ P21-13 8503-1 BELT COVER (LEFT)
※ P21-14 8503-2 BELT COVER (RIGHT)
※ P21-15 5276 BELT COVER SET SCREW
※ P21-16 8185 BELT COVER WASHER
※ P21-17 11554 BELT COVER BRACKET
※ P21-18 5233 BELT COVER BRACKET SET SCREW
※ P21-19 11557 BELT COVER BRACKET WOOD SCREW
※ P21-20 8184 BELT COVER WOOD SCREW

※ EXTRA ACCESSORIES

38
23. STANDARD ACCESSORIES

39
REF. NO. PARTS NO. DESCRIPTION
P23-1 AC-01 SCREW DRIVER (LARGE)
P23-2 AC-02 SCREW DRIVER (MEDIUM)
P23-3 AC-03 SCREW DRIVER (SMALL)
P23-4 AC-04A OILER
P23-5 AC-05 OIL
P23-6 AC-08 ACCESSORY BOX
P23-7 8166 SCREW EYE
P23-8 8157 BED CLAMPING THUMB SCREW
P23-9 8165 MACHINE HINGE CONNECTION
P23-10 8493 TOOL (FOR ADJUSTING HINGE STUD #8455)
P23-11 8126 SPOOL SCREW STUD
P23-12 8171 PLIERS
P23-13 8168 THREAD KNIFE
P23-14 8170 TWEEZERS
P23-15 8169 MACHINE REST PIN (WOOD)
P23-16 8499 CLEANING WIRE
P23-17 8156 THREADER WIRE
P23-18 8497 SPOOL WINDER SPINDLE
P23-19 5249 SPOOL WINDER SPINDLE WASHER
P23-20 8073-B PRESSER FOOT SHOE (RUBBER)
P23-21 8027-3 NEEDLE (137*1 #3)
P23-22 8501-4 NIPPLE (FOR CHAINSTITCHING)
P23-23 8321-4 NIPPLE (FOR TAPE-ATTACHING)
P23-24 8505 PRESSER FOOT (SPUR)
P23-25 8467 BRAID SPOOL (METAL)
P23-26 8502 SPOOL (WOOD)
P23-27 AC-06 WRENCH (3MM)

40
 USA
web: www.consew.com

Specifications subject to change without notice. ©2017 Consew USA