Spacial - SFM - MCC

www.schneider-electric.
com
Spacial SFM Compartmentalised enclosure

for Motor Control Centres
Fixed compartmentalised swithchboards
The Spacial SFM compartmentalised functional fixed system can be used for motor
control centres in industrial environments (IP54).
It has been tested taking into account device characteristics.
This ensures a high degree of reliability in system operation and optimum safety.
Devices can be mounted on universal mounting plates on a workcut-out to simplify
installation in the switchboard.
Fixed functional system for Motor Control

The fixed functional system for Motor Control Centres is designed for installation
PB502998-75
of motor starters up to 250 kW.
326
UE16MK16.indb 326 21/09/2016 14:21

www.schneider-electric.com

Motor protection
In addition to the motor power and the starter type (direct, reversing, star-delta…),
4 main criteria have to be taken into account when choosing a motor starter:
b the operational voltage,
b the type of thermal protection, electro-mechanical or electronical,
b the type of magnetic protection, according to the switchboard’s Isc,
b the type of installation, according to the required availability level.
Operational voltage
Network’s operational voltage is a decisive parameter in the choice of motor protection.
Indeed, the operational voltage will have an impact on the device’s performances
and the installation constraints.
For instance, the voltage will influence:
b the breaking performances,
b the safety areas.
Motor protection
Protecting the motors to extend their lifetime
b Overheating in electrical motors is caused by copper and ferro-magnetic losses:
v the current I is proportional to the motor’s load. Copper losses are proportional
DD405318_SE
to I2 (stator and rotor),

v hysteresis cycles in ferro-magnetic materials and the induced Foucault currents
cause overheating, which is in particular proportional to frequency.
b The consequence of abnormal overheatings is a reduced isolation capacity of the
materials, thus leading to a significant shortening of the motor lifetime, as shown in
the opposite diagram.
b In continuous or semi-continuous processes, availability is a major issue. It is
therefore decisive to observe accurately the operating conditions of the motors.
b Motor protection relays are the components dedicated to this task. They provide
various levels of accuracy and functionalities, in order to meet the expectations
of the process manager.
Supervising finely the motors to improve process availability

b An electrical motor transforms electrical energy in mechanical energy.
When the voltage, current and frequency change, the speed and torque of the motor
change too. And conversely, any changes in charge have a direct impact on the
DD405340
electrical parameters.
b Electromechanical thermal relays protect the motor against overloads.
b Electronical relays protect the motor against overloads, on the basis of very
sophisticated and highly accurate thermal patterns.
v These relays are able to make out several cases of motor overload, and to
transmit the information, thus allowing the operator to have a better understanding
of the true nature of the problem,
v These relays report for many complementary parameters, providing useful
informations to the operator, therefore giving him the opportunity to avoid motor
stops, or to re-start quickly if a stop has occurred.
v Examples:
- motor under-load can be the signal of a pump cavitation,
- phase inversion can be the indication of a maintenance error, that should be hard
to diagnose without that sign.
v In addition to the observation of currents, the electronical relays can monitor
the voltage, and consequently the power and the power factor. They can also watch
the leakage currents and measure the actual coil temperature whenever it has a
built-in sensor.
DD405342_SE
All these informations give an additional level of anticipation and shrewdness

to help coping with problems.
v Finally, electronical relays can take on information-processing functions, like state
and faults statistics. They are also able to suggest logical solutions, and to react in a
process-specific way.
327
UE16MK16.indb 327 21/09/2016 14:21


Motor protection
Magnetic protection: circuit-breakers and fuses

Schneider Electric have chosen to put forward circuit-breakers each time it is
possible, as they have advantages in terms of maintenance and capacity of
quick re-operating.
The advantages of magnetic circuit breakers over fuses are listed below:
b universal solution that can be exported to all countries, unlike the fuses,
which standards are not coordinated,
b reduced dimensions,
b limited temperature rise,
b faster maintenance,
b no risk of over-rating the fuse cartridge (causing the motor destruction)
or underrating (untimely tripping).
Spacial SFM: a combination for control motor starter
Circuit breaker
PB103219-14
NS80
GV2-GV3
GV7
NSX100-630 Power supply

NS100H
and network
105533-19
103283-16_SE
LC1D
LC1F
LRD
Relay
Contactors Feeder
328
UE16MK16.indb 328 21/09/2016 14:21


Coordination
DD383428
Coordination, what is it about?

A "motor starter" can be made up of 1, 2, or 3 different devices. They have to be
coordinated in a way they ensure an optimal operation of the installation.
Aims of coordination
In case of a fault, the coordination’s purposes are:
b to protect of the people and the equipment,
b to permit continuity of service,
b to reduce maintenance costs (manpower and replacement equipment).
Type 1 coordination
Types of coordination as per IEC 60947-4-1
b Type 1 coordination: basic solution
v no continuity of service,
DD383429
v important maintenance costs in case of a fault (manpower and equipment).

b Type 2 coordination: solution ensuring continuity of service
v reduced machine shutdown time,
v reduced cost of replacement equipment.
b Total coordination, as per IEC 60947-6-2:
v no damage nor resetting of devices following a fault,
v installation immediate return to operation.
Type 2 coordination
DD383430
Total coordination
Schneider Electric’s choice as regards coordination

For applications in Spacial SFM high availability switchboard, Schneider Electric
has accepted:
type 2 or total coordination on grounds of:
b a low cost for repairing the equipment,
b a reduced machine shutdown time,
and dismissed:
type 1 coordination and non-coordoned feeders because of:
b an expensive return to operation,
b a long machine shutdown time.
329
UE16MK16.indb 329 21/09/2016 14:21


Motor starter solutions
PD405140-30
2-component motor starter

Thermomagnetic circuit-breaker + contactor
b Advantages
v Very economic solutions.
v Suitable for all types of diagrams.
v Manual reset following a thermal fault.
v Type 2 coordination.
b Applications
v Manufacturing and continuous and semi-continuous processes.

PD405141-30
b Advantages
v Wide choice of solutions.
v Suitable for all types of diagrams.
v Manual or automatic reset following a thermal fault.
v 2 starting classes (10 and 20).
v Type 2 coordination.
v Segregation of thermal and magnetic faults.
b Magnetic circuit-breaker + contactor + thermal protection
v For manufacturing and continuous and semi-continuous processes.
b Switch-disconnector fuse + contactor + thermal protection
v For all types of machines.
v For manufacturing and continuous and semi-continuous processes.
330
UE16MK16.indb 330 21/09/2016 14:21


Enclosures
PB502987-70
Presentation
The Spacial SFM compartmentalised enclosures system used for MCC are based
on the Spacial SF range.
They offer the same functions:
b Different possible configurations, combined side-by-side or back-to-back.
b The built-in partial doors and panels design allow to meet the required degree
of protection.
And the same advantages:
b Save time through all assembly phases.
b Enclosure robustness.
Modularity and Versatility

They offer 36 vertical modules, each 50 mm high, of useful space.
They have 4 different enclosure dimensions and 2 additional chambers for
distribution busbars or cabling management.
They can also be coupled with Spacial SFP for power distribution switchboards.
The functional system

A metal structure
PB502985-32
The switchboard is made up of one or more frameworks combined side-by-side

or back-to-back, on which a complete selection of cover panels and partial doors
can be mounted.
They are used to build IP54 configurations and see ClimaSys offer options
for ventilation.
Electrical continuity is achieved using earthing braids.
Plain partial doors are reversible for quick left or right-hand mounting by a single
person, 120º opening.
The robustness of the locking system allows naturally the good alingment of
the assembly. From 1 to 4 locking points system with 5 mm double-bar insert
as standard supply with possibility to replace it by other shape insert.
A distribution system
Vertical busbars positioned in a lateral compartment and horizontal busbars are
used to distribute electricity throughout the switchboard.
Complete functional units

The functional unit need to be composed by:
b motor control and protection devices,
b a dedicated plain mounting plate for device installation,
b up to form 4b thanks to the gland boxes for the terminal isolation on the back of
the switchboard or on the side of the cabling chamber,
b devices for on-site connections.
The functional units are modular and designed for installation one on top of another.
The system includes everything required for functional unit mounting, supply and
onsite connection.
The components of the Spacial SFM compartmentalised system and those of the
functional units in particular have been designed and tested taking into account
device characteristics. This design approach ensures a high degree of reliability in
system operation and optimum safety for personnel.
Electrical switchboards built using Schneider Electric recommendations fully comply
with international standard IEC 61439-1&2 and IEC 62208.
331
UE16MK16.indb 331 21/09/2016 14:21


Enclosures
Withstand to the most demanding environements

b IP54 degree of protection for the dusty and/or damp industrial environments.
b Seismic withstand.
b Optional forced ventilation for environments with ambient temperatures hotter
than 45°C or for devices sith considerable heat loss (see ClimaSys offer options).
Type tested
Spacial SFM compartmentalised is totally type-tested in accordance with
IEC 61439-1&2.
b Certified by independant lab.
b As well as by a permanent control in Schneider Electric test laboratories.
b Type-tests are carried out:
v temperature-rise limit,
v dielectric properties,
v short-circuit withstand,
v effectiveness of the protective circuit,
v conformity of the clearance and creepage distances,
v mechanical operation,
v degree of protection.
Partitioning
PB502988-62
Partitioning is essential to ensure the utmost protection of the installation and

personnel carrying out work in the switchboard.
Used in conjunction with the standard protection (terminal shields, factory-built
connections), partitioning prevents any direct contact with live parts.
Form 2b
b Terminals for external conductors separated
from busbars.
b The functional units and the terminals are
separated from the busbars.
Form 3b
Separation of busbars from the functional units and
separation of all functional units from one another.
Separation of the terminals for external conductors
from the functional units, but not from each other.
b Protection against contact with live parts.
b Reduction in the risk of faults between the functional
units (propagation of electrical arcs, etc.).
Form 4b
Terminals for external conductors not in the same
compartment as the associated functional unit,
but in individual, separate, enclosed protected
spaces or compartments.
332
UE16MK16.indb 332 21/09/2016 14:21


Fix enclosures
General data
PB502999-71
Applications MCC
Standards IEC 61439-1&2
Internal arc No
Seismic 3G
Installation Indoor
Mechanical data
Cable inlet Top / Bottom
Access Front / Rear Side
IP 54
IK 10
Form 4b type 7
Withdrability FFF
Dimensions H 2000 / W 600 & 800 / D 600 & 800
Color RAL 7035
Electrical data
Insulation voltage (Ui) 1000 V
Voltage rating(Ue) 415 V
Coordination Type 2
Frequency 50/60 Hz
Auxiliary circuit voltage 230 V
Degree of pollution 3
Rated current (IP>31) 2500 A (with Copper & Linergy)
Short circuit (Icw - 1s) 85 kA
333
UE16MK16.indb 333 21/09/2016 14:21


Mounting plates for fixed
MCC switchboards
Motor control functional units
PB502989-60
The plain mounting plates can be used to install all the devices making up an
MCC motor starter on a single support.
Easy installation
Motor feeders can be prepared on a bench making the cut-outs needed.
PB502990-58
The quick-fixing system allows to hold the mounting plate during device installation
and wiring. The mounting plate can be fixed on the side partitions in adjustable depth
with a pitch of 50 mm.
Switchboard upgradeability
b Functional units with form partitioning 3b and 4b.
PB502991-66
b Sides and Rear accessibility.

b Separation panels with pre-cuts for cable-glands ref. 01215.
Functional unit reliability

b The unit of height for the mounting plates is the 50 mm module.
b 3 to 24 module (150 to 1200 mm) mounting plates are installed in 600 and 800 mm
wide cubicles.
b Capacity of Spacial SFM cubicles: 36 modules (50 mm each).
b Cables are run in dedicated 300 or 400 mm wide lateral compartments.
Plain mounting plates
Fixing kit
Mounting plate
Dimension of the compartment References

Number of Rate Width Mounting plate Fixing kit
modules (mm) (mm)
3M 150 600 NSYMP3M6 NSYMPFIX
800 NSYMP3M8
4M 200 600 NSYMP4M6
800 NSYMP4M8
5M 250 600 NSYMP5M6
800 NSYMP5M8
8M 250 600 NSYMP8M6
800 NSYMP8M8
9M 450 600 NSYMP9M6
800 NSYMP9M8
12M 600 600 NSYMP12M6
800 NSYMP12M8
16M 800 600 NSYMP16M6
800 NSYMP16M8
18M 800 600 NSYMP18M6
800 NSYMP18M8
20M 800 600 NSYMP20M6
800 NSYMP20M8
24M 800 600 NSYMP24M6
800 NSYMP24M8
334
UE16MK16.indb 334 21/09/2016 14:21


Direct on line and reversing GV2, GV3 and GV7
Selection of recommended combinations
Iq (kA) Motor characteristics Motor starter solution Mounting plate

Number of modules (1M = 50 mm)
Without limiter With GV1L3 P max (kW) I max (A) Circuit breaker Contactor (1) DOL Reversing
GV2
85 - 0.18 0.6 GV2-P04 LC1D09 3M 3M
85 - 0.25 0.9 GV2-P05 LC1D09 3M 3M
85 - 0.37 1.1 GV2-P06 LC1D09 3M 3M
85 - 0.55 1.5 GV2-P06 LC1D09 3M 3M
85 - 0.75 1.8 GV2-P07 LC1D09 3M 3M
85 - 1.1 2.6 GV2-P08 LC1D09 3M 3M
85 - 1.5 3.4 GV2-P08 LC1D09 3M 3M
85 - 2.2 4.8 GV2-P10 LC1D09 3M 3M
85 - 3 6.5 GV2-P14 LC1D09 3M 3M
85 - 4 8.2 GV2-P14 LC1D18 3M 3M
50 85 5.5 11 GV2-P16 LC1D25 3M 3M

50 85 7.5 14 GV2-P20 LC1D25 3M 3M
50 85 10 19 GV2-P21 LC1D32 3M 3M
50 85 11 21 GV2-P22 LC1D32 3M 3M
50 85 15 28 GV2-P32 LC1D32 3M 3M
50 - 18.5 34 GV3-P40 LC1D50A 3M 4M
50 - 22 40 GV3-P50 LC1D50A 3M 4M
50 - 30 55 GV3-P65 LC1D65 3M 4M
70 - 15 28 GV7-RS40 LC1D40 3M 6M
70 - 18.5 34 GV7-RS40 LC1D50 3M 6M
70 - 22 40 GV7-RS50 LC1D80 3M 6M
70 - 30 55 GV7-RS80 LC1D80 3M 6M
70 - 37 66 GV7-RS80 LC1D80 3M 6M
70 - 45 80 GV7-RS100 LC1D115 4M 9M
70 - 55 100 GV7-RS150 LC1D150 6M 9M
70 - 75 135 GV7-RS150 LC1F185 9M 12M
70 - 90 160 GV7-RS220 LC1F225 9M 12M
70 - 110 200 GV7-RS220 LC1F265 9M 12M
(1) 2xLC1-D for reversing
Selection of the mounting plate

modules (mm) (mm)
800 NSYMP3M8
4M 200 600 NSYMP4M6
800 NSYMP4M8
6M 300 600 NSYMP6M6
800 NSYMP6M8
9M 450 600 NSYMP9M6
800 NSYMP9M8
12M 600 600 NSYMP12M6
800 NSYMP12M8
335
UE16MK16.indb 335 21/09/2016 14:21


Ue
415 V
IP
≤ IP54
Ambiant temperature
35°C
Direct on line and reversing GV2 and GV3

Without With P max I max Circuit Contactor (1) Thermal relay DOL Reversing
limiter LA9LB920 (kW) (A) breaker
85 - 0.18 0.6 GV2-L04 LC1D09 LRD04 3M 3M
85 - 0.25 0.9 GV2-L05 LC1D09 LRD05 3M 3M
85 - 0.37 1.1 GV2-L06 LC1D09 LRD06 3M 3M
85 - 0.55 1.5 GV2-L06 LC1D09 LRD06 3M 3M
85 - 0.75 1.8 GV2-L07 LC1D09 LRD07 3M 3M
85 - 1.1 2.6 GV2-L08 LC1D09 LRD08 3M 3M
85 - 1.5 3.4 GV2-L08 LC1D09 LRD08 3M 3M
85 - 2.2 4.8 GV2-L10 LC1D09 LRD10 3M 3M
85 - 3 6.5 GV2-L14 LC1D09 LRD12 3M 3M
85 - 4 8.2 GV2-L14 LC1D18 LRD14 3M 3M
50 85 5.5 11 GV2-L16 LC1D25 LRD16 3M 3M

50 85 7.5 14 GV2-L20 LC1D25 LRD21 3M 3M
50 85 10 19 GV2-L21 LC1D32 LRD22 3M 3M
50 85 11 21 GV2-L22 LC1D32 LRD22 3M 3M
50 85 13 24 GV2-L32 LC1D32 LRD32 3M 3M
50 - 18.5 34 GV3-L40 LC1D50A LRD340 3M 4M

50 - 22 40 GV3-L50 LC1D50A LRD350 3M 4M
50 - 26 49 GV3-L65 LC1D65A LRD365 3M 4M
(1) 2xLC1-D for reversing.

modules (mm) (mm)
800 NSYMP3M8
4M 200 600 NSYMP4M6
800 NSYMP4M8
336
UE16MK16.indb 336 21/09/2016 14:21


Ue
415 V
IP
≤ IP54
Ambiant temperature
35°C
Direct on line and reversing NS80H and NSX

P max (kW) I max (A) Circuit breaker Contactor (1) Thermal relay DOL Reversing
70 18.5 34 NS80H-MA LC1D50 LRD3355 3M 6M
70 22 40 NS80H-MA LC1D50 LRD3357 3M 6M
70 30 55 NS80H-MA LC1D65 LRD3359 3M 6M
70 37 66 NS80H-MA LC1D80 LRD3363 3M 6M
(2) 18.5 34 NSX100 MA LC1D80 LRD3355 3M 6M

(2) 22 40 NSX100 MA LC1D80 LRD3357 3M 6M
(2) 30 55 NSX100 MA LC1D80 LRD3359 3M 6M
(2) 37 64 NSX100 MA LC1D80 LRD3363 3M 6M
(2) 45 80 NSX100 MA LC1D115 LR9D5367 6M 9M
(2) 55 100 NSX160 MA LC1D150 LR9D5369 6M 9M
(2) 75 135 NSX160 MA LC1F185 LR9F5369 9M 12M
(2) 90 160 NSX250 MA LC1F225 LR9F5371 9M 12M
(2) 100 187 NSX250 MA LC1F265 LR9F5371 9M 12M
(2) 132 230 NSX400 1.3-M LC1F330 LR9F7375 12M 16M
(2) 160 270 NSX400 1.3-M LC1F330 LR9F7375 12M 16M
(2) 200 361 NSX630 1.3-M LC1F500 LR9F7379 16M 16M
(2) 220 380 NSX630 1.3-M LC1F500 LR9F7379 16M 16M
(2) 250 430 NSX630 1.3-M LC1F500 LR9F7379 16M 16M
(1) 2xLC1-D for reversing
(2) NSX...F = 36 kA
NSX...N = 50 kA
NSX...H = 70 kA
NSX...S = 85 kA
NSX400L = 150 kA
NSX630L = 150 kA

modules (mm) (mm)
800 NSYMP3M8
6M 300 600 NSYMP6M6
800 NSYMP6M8
9M 450 600 NSYMP9M6
800 NSYMP9M8
12M 600 600 NSYMP12M6
800 NSYMP12M8
16M 800 600 NSYMP16M6
800 NSYMP16M8
337
UE16MK16.indb 337 21/09/2016 14:21


Ue
415 V
IP
≤ IP54
Ambiant temperature
35°C
Star-delta GV2, GV3 and GV7

Number of modules
(1M = 50 mm)
Without limiter With GV1L3 P max (kW) I max (A) Circuit breaker Contactor Star-delta
85 - 0.37 1.1 GV2-P06 3xLC1D09 4M
85 - 0.55 1.5 GV2-P06 3xLC1D09 4M
85 - 0.75 1.8 GV2-P07 3xLC1D09 4M
85 - 1.1 2.6 GV2-P08 3xLC1D09 4M
85 - 1.5 3.4 GV2-P08 3xLC1D09 3M
85 - 2.2 4.8 GV2-P10 3xLC1D18 4M
85 - 3 6.5 GV2-P14 3xLC1D18 3M
85 - 4 8.2 GV2-P14 3xLC1D18 4M
50 85 5.5 11 GV2-P16 3xLC1D25 4M

50 85 7.5 14 GV2-P20 3xLC1D25 4M
50 85 10 19 GV2-P21 3xLC1D32 5M
50 85 11 21 GV2-P22 3xLC1D32 4M
35 85 15 28 GV2-P32 3xLC1D32 4M
50 - 18.5 34 GV3-P40 3xLC1D50A 5M

50 - 22 40 GV3-P50 3xLC1D50A 5M
50 - 30 55 GV3-P65 3xLC1D65A 5M
70 - 15 28 GV7-RS40 3xLC1D80 9M
70 - 18.5 34 GV7-RS40 3xLC1D50 9M
70 - 22 40 GV7-RS50 3xLC1D80 9M
70 - 30 55 GV7-RS80 3xLC1D80 9M
70 - 45 80 GV7-RS100 3xLC1D115 12M
70 - 55 100 GV7-RS150 3xLC1D150 12M
70 - 75 135 GV7-RS150 3xLC1F185 16M
70 - 90 160 GV7-RS220 3xLC1F225 16M
70 - 110 200 GV7-RS220 3xLC1F265 16M

modules (mm) (mm)
800 NSYMP3M8
4M 200 600 NSYMP4M6
800 NSYMP4M8
5M 250 600 NSYMP5M6
800 NSYMP5M8
9M 450 600 NSYMP9M6
800 NSYMP9M8
12M 600 600 NSYMP12M6
800 NSYMP12M8
16M 800 600 NSYMP16M6
800 NSYMP16M8
338
UE16MK16.indb 338 21/09/2016 14:21


Ue
415 V
IP
≤ IP54
Ambiant temperature
35°C
Star-delta GV2 and GV3

Number of modules
(1M = 50 mm)
Without limiter With LA9LB920 P max (kW) I max (A) Circuit breaker Contactor Thermal relay Star-delta
85 - 0.37 1.1 GV2-L06 3xLC1D09 LRD06 4M
85 - 0.55 1.5 GV2-L06 3xLC1D09 LRD06 4M
85 - 0.75 1.8 GV2-L07 3xLC1D09 LRD07 4M
85 - 1.1 2.6 GV2-L08 3xLC1D09 LRD08 4M
85 - 1.5 3.4 GV2-L08 3xLC1D09 LRD08 4M
85 - 2.2 4.8 GV2-L10 3xLC1D18 LRD10 4M
85 - 3 6.5 GV2-L14 3xLC1D18 LRD12 4M
85 - 4 8.2 GV2-L14 3xLC1D18 LRD14 4M
50 85 5.5 11 GV2-L16 3xLC1D25 LRD16 4M

50 85 7.5 14 GV2-L20 3xLC1D25 LRD21 4M
50 85 10 19 GV2-L21 3xLC1D32 LRD22 4M
50 85 11 21 GV2-L22 3xLC1D32 LRD22 4M
35 85 15 24 GV2-L32 3xLC1D32 LRD32 4M
50 - 18.5 34 GV3-L40 3xLC1D50A LRD340 5M

50 - 22 40 GV3-L50 3xLC1D50A LRD350 5M
50 - 30 49 GV3-L65 3xLC1D65A LRD365 5M

modules (mm) (mm)
800 NSYMP4M8
5M 250 600 NSYMP5M6
800 NSYMP5M8
339
UE16MK16.indb 339 21/09/2016 14:21


Ue
415 V
IP
≤ IP54
Ambiant temperature
35°C
Star-delta NS80H and NSX

Number of modules
(1M = 50 mm)
P max (kW) I max (A) Circuit breaker Contactor Thermal relay Star-delta
70 18.5 34 NS80H-MA 3xLC1D50 LRD3355 9M
70 22 40 NS80H-MA 3xLC1D50 LRD3357 9M
70 30 55 NS80H-MA 3xLC1D65 LRD3359 9M
70 37 66 NS80H-MA 3xLC1D80 LRD3363 9M
(1) 18.5 34 NSX100 MA 3xLC1D80 LRD3355 9M

(1) 22 40 NSX100 MA 3xLC1D80 LRD3357 9M
(1) 30 55 NSX100 MA 3xLC1D80 LRD3359 9M
(1) 37 64 NSX100 MA 3xLC1D80 LRD3363 9M
(1) 45 80 NSX100 MA 3xLC1D115 LR9D5367 12M
(1) 55 100 NSX160 MA 3xLC1D150 LR9D5369 12M
(1) 75 135 NSX160 MA 3xLC1F185 LR9F5369 16M
(1) 90 160 NSX250 MA 3xLC1F225 LR9F5371 16M
(1) 110 187 NSX250 MA 3xLC1F265 LR9F5371 16M
(1) 132 230 NSX400 1.3-M 3xLC1F330 LR9F7375 20M
(1) 160 270 NSX400 1.3-M 3xLC1F330 LR9F7375 20M
(1) 200 361 NSX630 1.3-M 3xLC1F500 LR9F7379 24M
(1) 220 380 NSX630 1.3-M 3xLC1F500 LR9F7379 24M
(1) 250 430 NSX630 1.3-M 3xLC1F500 LR9F7379 24M
(1) NSX...F = 36 kA
NSX...N = 50 kA
NSX...H = 70 kA
NSX...S = 85 kA
NSX400L = 150 kA
NSX630L = 150 kA

modules (mm) (mm)
800 NSYMP9M8
12M 600 600 NSYMP12M6
800 NSYMP12M8
16M 800 600 NSYMP16M6
800 NSYMP16M8
20M 1000 600 NSYMP20M6
800 NSYMP20M8
24M 1200 600 NSYMP24M6
800 NSYMP24M8
340
UE16MK16.indb 340 21/09/2016 14:21


Linergy distribution systems
Linergy LGYE-LGY
a breakthrough in busbar systems
Safe, reliable, The Linergy LGYE-LGY busbar system now includes
flexible, and horizontal busbars, for greater electrical switchboard

enclosure performance, reliability, and costeffectiveness.
flexible with
the highest Manufactured using a revolutionary process, patented
level of Linergy busbars are unique on the market, taking your
performance electrical switchboard installations a giant leap
into the future.
PB502992-103
Discover how
Linergy LGYE-LGY
can place the next

generation of low-voltage
switchboards in your
hands.
341
UE16MK16.indb 341 21/09/2016 14:21


Innovative technology
from an energy expert you can trust
Patented Linergy LGYE-LGY is backed by Schneider Electric’s decades
of expertise in electrical distribution systems and is certified IEC 61439-2
compliant by ASEFA.
Linergy unique profile was designed Linergy LGYE-LGY busbars

with the ratings you need, a commitment to performances are identical or better than
performance backed by regular testing up to traditional all Linergy BS busbars.
4000 A.
Heat is dissipated by conduction Unlike tin-plated aluminum

and radiation for performance only a market busbars, rugged Linergy LGYE-LGY
leader can bring you. busbars are resistant to scratching during
assembly to ensure optimal connection quality
and reliability.
PB502993-68
PB502994-72
High Velocity Oxy-Fuel, unique

on the busbar market
Patented Linergy LGYE-LGY uses a supersonic high-temperature
coating process for a robust copper contact surface.
342
UE16MK16.indb 342 21/09/2016 14:21


A revolutionary design
for greater efficiency
The Linergy line now includes horizontal busbars, helping you achieve
better electrical switchboard performance while optimizing busbar layout
and facilitating assembly.
Schneider ElectricTM has drawn upon 30 years

of expertise in electrical distribution systems
Attractive
and a decade of hands-on experience with the The revolutionary copper contact strips,
proven and reliable Linergy line of products. anodized aluminum surface, and unique
It brings you a revolutionary design featuring shapes give a modern appearance and a soft
a high-quality copper contact surface that touch.
delivers even better results than traditional
Linergy BS-to-Linergy BS connections. IEC standards-compliant
Linergy LGYE-LGY busbars offer a number of The latest standards were factored in from
benefits to help you enhance performance and the early design stages to ensure that
boost your competitiveness. temperatures are kept below the IEC61439-2
standard requirements, for optimal performance
regardless of the switchboard configuration.
Lightweight
Linergy is half the weight of equivalent-
rated Linergy BS bars for more fuel-efficient Environmentally-friendly
transport, easier handling, and smoother Instead of increasingly-scarce copper, Linergy
installation. LGYE is made from 70% recycled raw materials
offering the same performance as primary raw
materials.
Higher-capacity
A single Linergy LGYE bar can withstand
ratings up to 2500 A. It would take two or three Cost-effective
Linergy BS bars per pole to achieve similar Linergy LGYE-LGY helps you achieve cost
ratings. savings now and provides protection against
fluctuating copper prices in the future, plus all
the advantages of a raw material that is easy
Robust and flexible to purchase and store.
Linergy LGYE bars are extruded for a unique
profile that includes both closed and ribbed
sections, improving rigidity, thermal dissipation,
and resistance to short circuits, with a
shortcircuit withstand capacity (lcw) of 85
kA/1s for SFM and 100 kA / 1s for Spacial SFP.
Linergy LGYE Reduce costs

is 50% and assembly
lighter than times over
Linergy BS Linergy BS busbars
343
UE16MK16.indb 343 21/09/2016 14:21


Linergy accessories are also

evolving!
Linergy LGYE is a full-featured busbar system that includes all
the connections, screws, bolts, isolating supports, and other
accessories you need for drill-free assembly.
IMG_0167-158
IMG_0116-13
PD384627-13
IMG_0121-13
IMG_0119-14
PD384625-25
PD384626-28
PD384628
Panel builders, we’ve thought of everything

to make your life easier!
t L
inergy LGYE-LGY busbars are lightweight, making t Linergy LGYE-LGY busbars offer a unique shape
them easy to transport and handle in the workshop. with no sharp edges for safer, smoother handling
and installation the bars simply slide right in
t W
ith Linergy LGYE-LGY, you can continue to use
to the busbar supports.
the familiar Spacial SFP busbar supports you
already know for Linergy BS bars. t Existing Linergy LGY vertical busbars are easy
There’s no new system to learn. to connect to Linergy LGYE with ready-toinstall
IMG_9657-48
accessories like vertical connectors.

t L
inergy LGYE-LGY offers single bars for each
rating, making handling during installation faster t Linergy materials are easy to recycle via
and more convenient. well-established aluminum recycling services
already in use for materials like aluminum cans,
t L
inergy LGYE-LGY bars are fast and easy to
coffee capsules, door and window frames,
position without drilling, thanks to a sliding bolt
and engine blocks.
and track system.
t L
inergy screws let you add extra outgoing
connections without drilling new holes or
dismounting previous connections or busbar
supports, saving you time and giving you greater
flexibility in the event of last-minute changes.
344
UE16MK16.indb 344 21/09/2016 14:21


Linergy also offers the most

advanced busbar solutions
while remaining simple.
PB502995-140
Linergy LGYE / LGY /BS > Solutions available up to 2500 A

Power busbars for Spacial SFM up to 4 000 A
for Spacial SFP.
> Connection everywhere without
drilling (with LGY and LGYE profile).
345
UE16MK16.indb 345 21/09/2016 14:21


Lateral Linergy busbars up to 1600 A
Busbar calculation
The following table indicates:
b the catalogue numbers of the bars to be used, depending on the permissible
current level in the busbars,
b the number of supports required, depending on the rated short-time withstand
current (Icw in kA rms / 1 second).
Linergy Cat. Permissible No. of supports

busbars no. current Icw (kA rms / 1 s)
at 35 °C for
switchboard
IP IP ≤ 25 ≤ 30 ≤ 40 ≤ 50 ≤ 60 ≤ 65 ≤ 75 ≤ 85
≤ 31 > 31
Linergy 630 04502 630 590
Linergy 800 04503 800 760
Linergy 1000 04504 1000 950 3
Linergy 1250 04505 1250 1170 4 5
Linergy 1600 04506 1600 1480 7 8
Note: the permissible current values for the busbars are given for an ambient
temperature of 35°C around the switchboard.
The bottom support also maintains the bars in position.
Each catalogue number represents one bar.
Busbar selection
Linergy busbars, L = 1670 mm
DB300923
Cat. no. selection

See the table below.
Each bar is supplied with a stop for the bottom support.
DD384147b
DD384148b
DD384149b
Bar 630 A. Bar 800 A. Bar 1000 A.

Cat. no. 04502 Cat. no. 04503 Cat. no. 04504
DD384150b
DD384151b
Bar 1250 A. Bar 1600 A.

Busbars up to 1600 A.
Cat. no. 04505 Cat. no. 04506
The bottom support also maintains the bars in position.
346
UE16MK16.indb 346 21/09/2016 14:21


Linergy LGY - Lateral profiles up to 1600 A
Linergy LGY profiles

Up to 1600 A (single busbar)
In Spacial SF busbar chamber W300
Linergy profile, 1670 mm length
Dd381233-LIN-7
DD381234-LIN-7
DD381235-LIN-7
DD381236-LIN-7
DD381237-LIN_7
630 A 800 A 1000 A 1250 A 1600 A
Permissible current for an ambient temp. of IP y 31 680 A 840 A 1040 A 1290 A 1650 A
35°C around the switchboard IP > 31 590 A 760 A 950 A 1170 A 1480 A
Number of profiles per phase 1
Cat. no. 04502 04503 04504 04505 04506
Busbar supports
DD380741-LIN
DD385383-EN
387.5 mm
max. Fixed support 04651
Characteristics An end stop must be fitted on the bottom support:
DD380742-LIN-12
01109 (sold in lots of 12)

700 mm
max.
Number depending y 25 3
700 mm
max.
on Icw y 30 - 3
(kA rms/1 s) y 40 - 3
y 50 - 4
y 60 - 5
y 65 - 5
y 75 - 7
y 85 - 8
Cat. no. 04651 (set of 2 upright adapters NSYSFPA and set of 2 40 mm universal cross-rail
NSYSUCR40200 for installation in Spacial SF busbar chamber)
Connections to the Linergy BS horizontal busbar
DD385409
Characteristics Supplied with mounting hardware.

Reference include 1 connection only. Order 1 connection per phase.
Cat. no 5 mm thick 04634 04635
according to 10 mm thick Width y 80 mm 04636
horizontal
busbar size
Connections to the Linergy LGYE horizontal busbar

DD385387
y 1600 A
Characteristics Supplied with mounting hardware.
Reference include 1 connection only. Order 1 connection per phase.
Cat. no. 04602 (vertical connection)
04603 (vertical shifted connection) (1)
(1) Dedicated connection 04603 for Linergy LGYE busbar in 150 mm busbar chamber with horizontal jointing.
347
UE16MK16.indb 347 21/09/2016 14:21


Linergy LGY - Horizontal profiles up to 2500 A
Linergy LGYE profiles

Installation in Spacial SFM Up to 1600 A Up to 2500 A
compartmentalised
Linergy profile, 2000 mm length
DD385352_1
DD385351_1
DD385350_1
DD385355_1
DD385354_1
DD385349_1
DD385353_1
60 60 60 60 60
100 100
23 23 23 23 23
31 31
630 A 800 A 1000 A 1250 A 1600 A 2000 A 2500 A

Permissible current for an ambient temp. 530 A 680 A 850 A 1050 A 1480 A 1650 A 2100 A
of 35°C around the switchboard
Number of profiles per phase 1
Total number of vertical modules (50 mm) 3 3
Cat. no. 04560 04561 04562 04563 04564 04565 04566
Busbar supports
DB300926
DD381225-LIN
DB300925
Fixed support Free support
Characteristics 2 fixed supports for Spacial SF wide cublicle are compulsory according compartment depth (400 or 500 mm).
1 fixed support for Spacial SF 300/400 wide chamber are compulsory. Fixed directly on framework.
If more supports are needed, add free supports.
In cubicle SFM: Number of y 15 2
W600/800 supports y 25 2
Busbar supports depending y 30 2
75 mm distance on Icw
between (kA rms/1 s) y 40 - 2
y 50 - 2
y 60 - 2+1 2
y 65 - 2+1
y 75 - 2+1
y 85 - 2+1
Cat. no. Fixed support D400 NSYMBHS4
D500 NSYMBHS5
Cat. no. Free support 04662
In busbar Number of y 15 1
chamber SF: supports y 25 1
W300/400 depending y 30 1
Busbar supports on Icw
y 40 1
75 mm distance (kA rms/1 s)
between y 50 1
y 60 1
y 65 1+1
y 75 1+1
y 85 1+1
Cat. no. Fixed support D600 NSYBHS600 NSYBHS600
D800 NSYBHS800 NSYBHS800
Cat. no. Free support 04662 04662
Joints
Up to 1600 A Up to 2500 A
630 A 800 A 1000 A 1250 A 1600 A 2000 A 2500 A
DD385380b
DD385382b
DD385381b
04620 04624
Cat. no. 3 x 04620 (3P) 3 x 04621 (3P)
4 x 04620 + 04624 (4P) 4 x 04621 + 04624 (4P)
Note Reference 04624 is compulsory when installing jointed Linergy LGYE 4P busbars and must be fitted where the
frames meet. When installed at the bottom of a cubicle, the busbar must be partitioned.
Note: for accessories, see page 351.
348
UE16MK16.indb 348 21/09/2016 14:21


Linergy BS - Lateral flat busbars up to 2500 A
Flat busbars
Up to 1600 A Up to 2500 A
In Spacial SF busbar chamber W300 D500/600/800 W300 D500/600/800
Pre-slotted copper, DD381505-LIN-EN
1675 mm length
Permissible current for an ambient IP > 31 750 A 900 A 1250 A 1600 A 1080 A 1250 A 1600 A 1850 A 2000 A 2500 A
temp. of 35°C around the switchboard
Busbar cross-section (mm) 60 x 5 80 x 5 60 x 5 80 x 5 50 x 10 60 x 10 80 x 10 50 x 10 60 x 10 80 x 10
Number of busbars per phase 1 2 1 2
Cat. no. 04516 04518 04516 04518 04525 04526 04528 04525 04526 04528
Busbar supports
100 mm
Description 3 fixed supports are compulsory to hold the busbar in position.
DD385370
max.
If more than 3 supports are needed, use free supports (in addition).
The bottom wedge support is used to place the busbar and ensure it is in the correct position.
350 mm
It does not count as a busbar support.
max.
350 mm
max. Number y 15 3 3
of supports y 25 3+2 3 3
350 mm
depending y 30 3+2 3+2 3
max.
on Icw
(kA rms/1 s) y 40 3+4 3+2 3+2
350 mm
y 50 3+4 3+2
max.
y 60 3+4 3+2
y 65 3+4 3+2
100 mm y 75 3+6 3+4
max.
y 85 3+4
Cat. no. of Spacial SF W300, D600 NSYBVS600 (fixed) + 04662 (free) + NSYAS600 (end stop support)
supports busbar chamber W300, D800 NSYBVS800 (fixed) + 04662 (free) + NSYAS800 (end stop support)
depending 75 mm distance
on distance between bars
between bars
and busbar
chamber
depth
Connections to the Linergy BS horizontal busbar

DB300924
DD385384
Characteristics For a busbar with 75 mm distance References 04636, 04637 are supplied individually:
between bars, the bars must be 1 connection per phase.
completely covered. Reference 04642 consists of 2 M8 x 140 screws which
Staggered assembly points between can replace the original M8 x 120 screws.
one bar and the next, to maintain the
necessary clearance distances.(1)
DD383399
1 vertical bar per 2 vertical bars 1 vertical bar per phase 2 vertical bars per phase
phase per phase
60 x 5 80 x 5 60 x 5 80 x 5 50 x 10 60 x 10 80 x 10 50 x 10 60 x 10 80 x 10
Cat. no. of the connection y 80 mm 04645 04636 04637 04637
piece depending on
horizontal busbar size
(1) Drill hole dimensions for 5 mm thick horizontal busbars. Drill hole dimensions for 10 mm thick horizontal busbars.
DD385424-EN
12.5
DD384320-LIN-EN
50/60/80/100
35 35 12.5
55 11 55
75 75
111 111
60
80
100
349
UE16MK16.indb 349 21/09/2016 14:21


Linergy BS - Horizontal flat busbars up to 2500 A
Flat busbars
Installation in Spacial SFM compartmentalised Hasta 1600 A Hasta 2500 A
Copper bar, 2000 mm length
Permissible current for an ambient temp. of 35°C 750 A 900 A 1250 A 1600 A 1600 A 1850 A 2000 A 2500 A
around the switchboard
Busbar cross-section (mm) 60 x 5 80 x 5 60 x 5 80 x 5 80 x 10 50 x 10 60 x 10 80 x 10
Number of busbars per phase 1 1 2 2 1 2 2 2
Total number of vertical modules (50 mm) 3
Nº cat. 04536 04538 04536 04538 04548 04545 04546 04548
Busbar supports
DD381225-LIN-15
DB300927
DB300926
Fixed support Free support
In cubicle SFM: Characteristics 2 fixed supports for Spacial SF wide cublicle are compulsory according compartment depth (400 or 500 mm).
W600/800 with 1 fixed support for Spacial SF 300/400 wide chamber are compulsory. Fixed directly on framework.
75 mm distance If more supports are needed, add free supports.
between bars Number of y 15 2
supports y 25 2+1 2
depending on Icw y 30 2+1 2
(kA rms/1 s)
y 40 2+1 2
y 50 - 2+1 2
y 60 - 2+1
y 65 - 2+1
y 75 - 2+2 2+1
y 85 - - 2+1
Cat. no. Fixed support NSYMBHS4 (D400)
or NSYMBHS5 (D500)
Free support 04662
In busbar Number y 30 1
chamber SF: depending on Icw y 50 1+1 1
W300/400 with (kA rms/1 s) y 85 - 2
75 mm distance
Cat. no. Fixed support NSYBHS600 (D600) NSYBHS600 (D600)
between bars
depending on or NSYBHS800 (D800) or NSYBHS800 (D800)
depth Free support 04662 04662
Joints
Installation in Spacial SFP Up to 1600 A Up to 2500 A
1 vertical bar per phase 2 vertical bars per phase 1 vert. bar 2 vertical bars per phase
per phase
Busbar cross-section (mm) 60 x 5 80 x 5 60 x 5 80 x 5 80 x 10 50 x 10 60 x 10 80 x 10
Sliding joints with self-breaking lock nut 04640 04641
DD385385b
DD385386b
Cat. no. 04640 04641 04640 04641 04641 04640 04640 04641
Note: When installed at the bottom of a cubicle, the busbar must be partitioned.
350
UE16MK16.indb 350 21/09/2016 14:21


Accessories
Accessories
DD381218-LIN-15
DD381219-LIN-15
DD381222-LIN-10
Linergy screw Plain washer Identification
Linergy screw Characteristics Sold in lots of 20: 20 screws + 20 nuts + 20 contact washers, class 8.8.
The screws slide into the profile and are then locked in the desired position.
Cat. no. 25 mm length see the table "Connections on Linergy LGYE & LGY" below
39 mm length
Steel plain Characteristics M8 sold in lots of 20.
washers Cat. no. ext. Ø20 mm 04772
ext. Ø24 mm 04773
ext. Ø28 mm 04774
Brass plain Characteristics M8 sold in lots of 20 for connection of y 25 mm2 lugs to Linergy.
washers Cat. no. ext. Ø20 mm 04775
Identification Characteristics 12 clip-on supports + N, L1, L2, L3, PE, PEN labels.
Cat. no. 04794
Characteristics Linergy LGYE busbar screw plate kit after sales service.
Cat. no. 01130
M8 bolts
DD380737b
Linergy BS, Characteristics Set of 20 bolts + 20 nuts + 40 contact washers.

20 bolts Cat. no. M8 x 20 04782
8.8 class M8 x 25 04783
M8 x 30 04784
M8 x 35 04785
M8 x 40 04786
M8 x 45 04787
M8 x 50 04788
Torque nuts
DD380735b
20 M8 Characteristics Can be used to obtain the correct tightening torque (28 Nm) recommended by then manufacturer, without
torque nuts using a torque wrench. Torque nuts may be used for all electrical connections.
Cat. no. 04759
Voltage tap-offs
DD380736b
20 M10 voltage Characteristics For small lugs (on low-current cables or measurement tap-offs), insert a conducting washer (cat. no. 04775)
tap-offs for two between the busbar and the lug.
6.35 mm tab Cat. no. 04229
connectors
Connections on Linergy LGYE & LGY

InA (A) Connection on Linergy Utilisation Cat no.
0 to 630 Cable Use the 25 mm Linergy screw Recommended 04766
Insulated flexible bar Use the 39 mm Linergy screw Possible 04767 (1)
800 to 1250 5 mm thick bar Use the 25 mm Linergy screw Recommended 04766
Use the 39 mm Linergy screw Possible 04767 (1)
Use the flat plate screw with 2 studs Possible 04768
1600 to 2500 5 or 10 mm thick bar Use the flat plate screw with 2 studs Recommended 04768
Use the 39 mm Linergy screw Possible 04767 (1)
3200 to 4000 10 mm thick bar Use the flat plate screw with 3 studs Recommended 04769
(1) 04767 is only compatible with Linergy LGY.
351
UE16MK16.indb 351 21/09/2016 14:21


Partitioning Form 2
Separation of busbars from the functional units:

b protection against contact with live parts upstream of the outgoing circuits,
b protection against penetration of foreign solid bodies.
Form 2 partitioning
Lateral partitioning Rear partitioning
DB300928
DB300929
Diagramas
300/400 600/800 300/400 600/800
DB300962
DB300963
600/800 600/800
Características b Set of 2 vertical metallic separation which guarantees good b Vertical metallic separation which guarantee good insulation of the
insulation of the sides of the compartment (IP2x). back of the compartment (IP2x).
b Top and bottom ends have knock-outs for installation of horizontal b Pre-cuts of 40 x 70 mm for cable-glands using grommets ref 01215
busbars and pre-cuts of 40 x 70 mm for cable-glands using grommets when Form 4b is required on back installation.
ref 01215 when Form 4b is required. b Direct fixing on structure of enclosure.
b Partition extension required for D800 mm.
b Direct fixing on structure of enclosure.
Nº cat. D600: NSYMSC206 W600: NSYMBC206
D800: NSYMSC206 + NSYMSC202 W800: NSYMBC208
Front and Rear busbar barrier Horizontal busbar barriers

DB300930
DB300960
DB300961
Diagramas
600/800 300/400 300/400 600/800 300/400
DB300964
DB300965
600/800
W300 W400 W600 W800

Características b Front protection is realized by the b Set of 2 slotted barriers (front & rear), b Horizontal protection by the association of
association of the door W300 and this barrier. plus horizontal panel to be used when slotted front barrier and horizontal partition for
Metallic barrier, composed of 2 parts H850, busbars cross the cable chamber. ef¿cient natural conYection in the switchboard.
pre-cut at both ends
b Rear protection is realized by the
association of the back panel of the enclosure.
b The set can be used to partition horizontal busbar at the top or bottom of the cubicle.
b The space required for the busbars is not increased.
Nº cat. W300: 06540 D600: 06561 D600: NSYHPF2B3M4 D400: NSYHPF2B3M64 D400: NSYHPF2B3M84
W400: NSYVPF2B4 D800: 06563 D800: NSYHPF2B3M4 D500: NSYHPF2B3M65 D500: NSYHPF2B3M85
Note: when the busbars are at the bottom of the cubicle, gland plates are mandatory.
352
UE16MK16.indb 352 21/09/2016 14:22


Partitioning Form 3
Separation of busbars from the functional units and separation of all functional units
from one another.
Separation of the terminals for external conductors from the functional units, but not
from each other.
b protection against contact with live parts
b reduction in the risk of faults between the functional units (propagation of
electrical arcs, etc.).
Form 3 partitioning
Horizontal partitioning
DB300931
W600 W800
Characteristics b A horizontal metal partition to separate functional units from one another and guarantees insulation of the compartments (IP2x).
b It is fixed to the front uprights of the enclosure and the side partitions.
b Quick fixing system with intermediate crossbar to ensure the degree of protection of the partial doors.
b Order by multiples of 2 (2, 4, 6…).
Cat. no. D400: NSYMTR64 D400: NSYMTR84
D500: NSYMTR65 D500: NSYMTR85
353
UE16MK16.indb 353 21/09/2016 14:22


Partitioning Form 4
Separation of busbars from the functional units and separation of all functional units
from one another, including the terminals for external conductors which are an
integral part of the functional unit:
b Protection against contacts with live parts and reduction in the risk of faults
between the functional units (propagation of electrical arcs, etc.).
b Form 4a: terminal for external conductors in the same compartment as the
associated.
b Form 4b: Terminals for external conductors not in the same compartment as the
associated functional unit, but in individual, separate, enclosed protected spaces
or compartments.
Form 4b boxes
DB300932
DB300933
Characteristics b Metallic plain box composed by 2 parts that can be easily installed for side or rear connection to separate the terminals for external
conductors of the functional unit.
b Quick fixing system on the side or on the back partition.
b Available in 6 heights:
Cat. no. 3M: NSYBF4B3M 4M: NSYBF4B4M 5M: NSYBF4B5M 6M: NSYBF4B6M 8M: NSYBF4B8M 9M: NSYBF4B9M
Other universal common accessories
Rail support bracket

PB502723-20
Characteristics b Bracket for fixing rails at an angle of 45º.

b Reference by unit. Order by multiples of 10 (10, 20, 30…).
Cat. no. NSYFB45
Mounting & Cable management acc.

PB500964-20
PB500864-36
Cat. no. See on Universal Enclosure catalogue
354
UE16MK16.indb 354 21/09/2016 14:22


Selection of Spacial enclosures
Common characteristics
b Spacial SFM framework with compartmentalised system that can be combined
side-by-side with busbar and cable chambers.
b Receive the cover panels and partial doors IP54.
b Material: steel.
b Finish: painted with epoxy-polyester resin.
b Colour: RAL 7035 grey.
b Possibility to order it assembled or kit supply.
Compartmentalised enclosure
Assembled supply
PB500207-16 Kit supply
PB500129-7
PB500127-13
PB500128-16
W600 W800 W600 W800
Characteristics b Structure: Top and bottom frame and vertical uprights H2000 mm.
b Useful height for doors H1800 mm /36M, when are installed the top and bottom fix panels for
modularity (mandatory for installation of partial doors).
b Equipped with removable roof, external fixing rear panel and top & bottom fixed panels
(H100 mm) to allow modularity of partial doors.
b 4 dimensions available.
Cat. no. D600: NSYSF20660M D600: NSYSF20860M - -
D800: NSYSF20680M D800: NSYSF20880M
Vertical uprights H2000 mm - - NSYSFV20 NSYSFV20
Top & Bottom frame with roof - - D600: NSYSFC66 D600: NSYSFC86
D800: NSYSFC68 D800: NSYSFC88
Rear panel - - NSYBP206 NSYBP208
Fixed panels for modularty H100 mm /2M - - See table below See table below
(intermediate crossbars included)
External claddings
Front Fix panel for modularity Frontal partial doors Side panels
PB500114-17
PB500640-50
PB500637-27
W600 W800 W600 W800 D600 D800

Characteristics b Top & bottom fix panel to obtain modularity b Plain partial door with lock 5 mm double-bar b Set of 2 side panels fixed to the outside
required to install partial doors. insert. of the enclosure.
b If there is no horizontal partitioning on top b They are fixed to the uprights of the framework b Captive screws pre-mounted on
or bottom, the intermediate crossbar has to be by means of hinges. the panels.
ordered separately, ref. NSYMIC6 (W600 mm) b Drilling template for uprights ref. NSYMDT b Available in 2 depths (mm).
or NSYMIC8 (W800 mm). (Only 1 drilling template by order is needed).
b 2M fixed panels are delivered as standard b Opening to right or left.
for the compartmentalized enclosure. b 1, 2 or 4 locking points according different heights.
Possibility to order it separately for b Possibility to replace locking insert
Spacial SFM framework in kit supply. (see page 357).
b Available in 2 heights(M) (1). b Available in following heights(M) (1).
Cat. no. 2M: NSYMFP2M6 2M: NSYMFP2M8 3M: NSYMPD3M6 3M: NSYMPD3M8 NSY2SP206 NSY2SP208
5M: NSYMFP5M6 5M: NSYMFP5M8 4M: NSYMPD4M6 4M: NSYMPD4M8
5M: NSYMPD5M6 5M: NSYMPD5M8
(1) Heights according modularity (1M = 50 mm).
355
UE16MK16.indb 355 21/09/2016 14:22


Selection of Spacial enclosures
Busbar & cabling chambers
Assembled supply Kit supply
PB500739-14
PB500129-7
PB500130-7
PB500127-13
PB500128-16
W300 W400 W300 W400
Characteristics b Structure: Top and bottom frame and vertical uprights H2000 mm.
b Equipped with removable roof, external fixing rear panel and front plain door with 4 point locking
system with handle and DB 5 mm insert.
b 4 dimensions available.
Cat. no. D600: NSYSF20360 D600: NSYSF20460 - -
D800: NSYSF20380 D800: NSYSF20480
Vertical uprights H2000 mm - - NSYSFV20 NSYSFV20
Top & Bottom frame with roof - - D600: NSYSFC36 D600: NSYSFC46
D800: NSYSFC38 D800: NSYSFC48
Rear panel - - NSYBP203 NSYBP204
Front plain door - - NSYSFD203 NSYSFD204
356
UE16MK16.indb 356 21/09/2016 14:22


Spacial accessories
Other composition accessories

Cable-gland plates Plinth (100 mm height) Plinth (200 mm height)
PB502578-21
PB502581-13
PB502580-12
PB500115-15
PB502579-21
PB500116-15
PB500117-15
H (mm) W (mm) D (mm) Plain 1 entry 2 entries Front kit Side kit Front kit Side kit
2000 600 600 NSYEC66 NSYEC661 NSYEC662 NSYSPF6100 NSYSPS6100 NSYSPF6200 NSYSPS6200
2000 300 600 NSYEC36 NSYEC361 - NSYSPF3100 NSYSPS6100 NSYSPF3200 NSYSPS6200
2000 300 800 - NSYEC381 - NSYSPF3100 NSYSPS8100 NSYSPF3200 NSYSPS8200
Coupling kit 4 lifting eyebolts 4 lifting brackets Earthing cable Locks for partial doors
(3)
Possibility to replace standard insert by
one from the table below (CRN range) and
NSYFELB-12
PB500217-18
DD384440-18
PB502553-12
by keeping the standard latch.

Type of lock Insert references Key references
3 mm NSYTDBCRN* NSYLDB5
double bar
Characteristics b Side-by-side b Use a set of lifting b When two b For 6 mm NSYTC6CRN NSYLC7
combination. eyebolts rings for cubicles with NSYEL166D8:
7 mm NSYTC7CRN NSYLC7
b Back-to-back each framework (4). devices have been Length 160 mm,
(2)
combination . combined, use a Section 6 mm2, 8 mm NSYTC8CRN NSYLC8
lifting brackets. Terminal 8.3 mm.
b For 6.5 mm NSYTT6CRN NSYLT8
NSYEL3525D8:
Length 350 mm, 7 mm NSYTT7CRN NSYLT8
Section 25 mm2,
Terminal 8.3 mm. 8 mm NSYTT8CRN NSYLT8
Cat. no. NSYSFBK19 NSYSFEB NSYSFELB NSYEL166D8 /
NSYEL3525D8 * Delivered with 1 metal key.
(2) Back to back association must be shipped individually and combined during on-site installation.
(3) An earthing braid must be installed between the roof and the frame.
(4) For 2 columns: For 3 columns:
Lifting eyebolts
Lifting brackets
300/400 600/800 300/400 600/800 300/400
For more than 3 colomuns, lenghts > 1600 mm, see Lifting bars options on
Universal Enclosures catalogue.
357
UE16MK16.indb 357 21/09/2016 14:22


Standard IEC 61439
The main 10 functions of standard IEC 61439

For each of the following 10 functions, the standard IEC 61439 requires design
Both the point of arrival verifications from the system manufacturer - mainly through type-tests - and routine
of energy and a device verifications on each panel from the Panel Builder to achieve 3 basic goals: safety,
for distribution to the site continuity of service and compliance with end-user requirements.
applications, the LV switchboard
is the intelligence of the Safety
system, central to the electrical
b Voltage stresses withstand capability
installation. To withstand long term voltages, and transient and temporary overvoltages
It plays an essential role in the availability of according to the insulation coordination principles
electric power, while meeting the needs of and requirements.
personal and property safety. b Current-carrying capability
Its definition, design and installation are To protect against burns and to withstand temperature rise:
based on precise rules; there is no place for v when any circuit is continuously loaded, alone, to the specified current
improvisation. The IEC 61439 standard aims v when the assembly is loaded to the specified current according to the specified
to better define "low-voltage switchgear and load pattern (between circuits and/or as a function of the time).
controlgear assemblies", ensuring that the b Short-circuit withstand capability
specified performances are reached. It To withstand the stresses resulting from the prospective short-circuit current and
specifies in particular: from the associated data (High forces between conductors, temp. rise in a very short
b the responsibilities of each player, time, air ionization, overpressure).
distinguishing those of the original b Protection against electric shock
equipment manufacturer; the organization v Hazardous-live-parts not to be accessible (basic protection).
that performed the original design and v Accessible conductive parts not to become hazardous-live (fault protection).
associated verification of an assembly in b Protection against risk of fire or explosion
accordance with the standard, v Resistance to internal glowing elements.
and of the assembly manufacturer - the Note: Protection of persons, and optional protection of the assembly, against arcing
organization taking responsibility for the due to internal fault can be specified through a "special test" according to IEC 61641.
finished assembly
b the design and verification rules,
constituting a benchmark for product
certification
All the component parts of the electrical
switchboard are concerned by the IEC 61439 Continuity of service
standard. Equipment produced in
accordance with the requirements of this b Maintenance and modification capability
switchboard standard ensures the safety and Capability to preserve continuity of supply without impairing safety during assembly
reliability of the installation. maintenance or modification.
v Electrical condition of the assembly or various circuits.
v Speed of exchange of the functional units.
v Test facilities…
b Electro-Magnetic compatibility
To properly function (immunity) and not to generate EM disturbances (emission)
in specified environmental conditions:
v Industrial networks or locations (Environment A).
v Domestic, commercial, and light industrial locations (Environment B).
Compliance with end-user requirements

b Capability to operate the electrical installation
To properly function, according to:
v the electrical diagram of the overall system and related
information (voltages, coordination…),
v the specified operating facilities (e.g. free or restricted access
to Man Machine Interfaces, isolation of the outgoing circuits…).
b Capability to be installed on site
v To withstand handling, transport, storage… and installation constraints.
v Capability to be erected and connected (type of enclosure, type, material and
cross sectional areas of external conductors).
b Protection of the assembly against mechanical and atmospheric
environmental conditions
v Presence of water or solid foreign bodies (IP according to IEC 60529).
v External mechanical impacts (optional IK according to IEC 62262).
v Indoor or outdoor installation (humidity, UV).
358
UE16MK16.indb 358 21/09/2016 14:22


Enclosure standards
IEC 62208 and EN 50298
Standards IEC 62208 and EN 50298

Empty enclosures for low-voltage switchgear
and controlgear assemblies
General rules for empty enclosures
Standards IEC 62208 and EN 50298 lay down definitions, classifications,
characteristics and test requirements for the enclosures used for assemblies.
They apply to empty enclosures before installation of the devices by the panel
builder, as supplied by the manufacturer.
They apply to one-piece enclosures and to enclosures supplied in kit form.
Type tests
1 - Static load
2 - Hoisting
3 - Axial loads of metal inserts
4 - IK code
5 - IP code
6 - Thermal stability
7 - Resistance to heat
8 - Resistance to abnormal heat and to fire
9 - Dielectric strength
10 - Protective-circuit continuity
11 - Weather resistance
12 - Corrosion resistance
13 - Marking
359
UE16MK16.indb 359 21/09/2016 14:22

Spacial - SFM - MCC

Uploaded by

Copyright:

Available Formats

Spacial - SFM - MCC

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Spacial - SFM - MCC

Uploaded by

Copyright:

Available Formats

www.schneider-electric.

Spacial SFM Compartmentalised enclosure

Fixed functional system for Motor Control

UE16MK16.indb 326 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

to I2 (stator and rotor),

Supervising ﬁnely the motors to improve process availability

All these informations give an additional level of anticipation and shrewdness

UE16MK16.indb 327 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Magnetic protection: circuit-breakers and fuses

Spacial SFM: a combination for control motor starter

NSX100-630 Power supply

UE16MK16.indb 328 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Coordination, what is it about?

v important maintenance costs in case of a fault (manpower and equipment).

Schneider Electric’s choice as regards coordination

UE16MK16.indb 329 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

2-component motor starter

3-component motor starter

UE16MK16.indb 330 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Modularity and Versatility

The functional system

The switchboard is made up of one or more frameworks combined side-by-side

Complete functional units

UE16MK16.indb 331 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Withstand to the most demanding environements

Partitioning is essential to ensure the utmost protection of the installation and

UE16MK16.indb 332 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

UE16MK16.indb 333 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

b Sides and Rear accessibility.

Functional unit reliability

Plain mounting plates

Dimension of the compartment References

UE16MK16.indb 334 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Iq (kA) Motor characteristics Motor starter solution Mounting plate

50 85 5.5 11 GV2-P16 LC1D25 3M 3M

Selection of the mounting plate

Dimension of the compartment References

UE16MK16.indb 335 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Iq (kA) Motor characteristics Motor starter solution Mounting plate

50 85 5.5 11 GV2-L16 LC1D25 LRD16 3M 3M

50 - 18.5 34 GV3-L40 LC1D50A LRD340 3M 4M

Selection of the mounting plate

Dimension of the compartment References

UE16MK16.indb 336 21/09/2016 14:21

Spacial SFM Compartmentalised enclosure

Iq (kA) Motor characteristics Motor starter solution Mounting plate

(2) 18.5 34 NSX100 MA LC1D80 LRD3355 3M 6M

Selection of the mounting plate

Dimension of the compartment References