Stucor Me8594-Wo

DOWSNTULCOORAADPPED FROM
STUCOR APP
words, the vector sum of all external forces acting upon a system of rigid bodies is
zero. The vector sum of all external moments and inertia torques acting upon a
system of rigid bodies is also separately zero.
6.What is the purpose of flywheel? How will you differentiate the function of
governor in engine with flywheel? (Nov / Dec 2016, Nov / Dec 2011 , Nov / Dec
2012)
 The function of a governor is to regulate the mean speed of an
engine, when there are variations in the load.
 The function of a flywheel is to reduce the fluctuations of speed
caused by the fluctuation of the engine turning moment during each cycle
of operation.
7. Distinguish between static force and inertia force. ( May /June 2013)
 While analyzing the mechanism, if mass of the body and inertia force are not
considered, then it is called static force.
 Inertia Force Is A Fictitious Force Which When Acts Upon A Rigid
Body, Brings It In An Equilibrium
8. What is engine shaking force? (May /June 2013)

The force produces in an engine due to the mass of the piston, and mass
of the connecting rod is called engine shaking force.
9. Write the conditions for any distributed mass have the same dynamical
properties. (Nov / Dec 2013)
(i) The mass of the rigid body must equal to the sum of masses of two
concentrated masses, i.e. m1 +m2 = m
(ii) The centre of gravity of the two masses must concide with the centre of
gravity of the rigid body. i.e., m1 × l1 = m2 × l2
(iii) The sum of mass moment of inertia of two masses about their centre of
gravity is equal to the mass moment of the rigid body.
10. The length of the crank and connecting rod of vertical reciprocating engine are
300mm and 1.5 m respectively. If the crank rotates at 200 rpm, Find the
velocity of the piston at θ = 400 (Nov / Dec 2015)
Given Data:
= 300mm = 0.3m
= 1.5m
N = 200 rpm
θ = 400
11
STUCOR
DOWNLOADED FROM STUCOR
STUCOR APP
To find:
The velocity of the piston
Solution
= = = 20.93rad/s
= = = 0.2
Velocity of the piston when θ = 400
= 1.5 × 20.93
= 97.01m/s
PART B
1). The length of crank and connecting rod of the horizontal reciprocating engine
are 300mm and 1.2 m respectively. The cylinder bore is 0.5 m and the mass of
the reciprocating parts is 250 kg. The crank is rotating at 250 rpm. When the
crank has turned through 60° degree from the IDC, the difference of the
pressure between the cover and piston end is 0.35N/mm 2. Calculate i) Thrust
on sides of the cylinder walls.
ii) Thrust in the connecting rod.
iii) crank-pin effort
iv) Turning moment on crank shaft
(Nov / Dec 2010, Nov / Dec 2012, May /June 2014)
Given
r = 300mm = 0.3m
l =
1.2m
m = 250Kg
θ = 600
P1 - P2 = 0.35 N/mm2
D = 0.5m
N = 250 rpm
Solution:-
12
STUCOR
STUCOR APP
= 26.2 rad / s
1) Thrust on sides of the cylinder walls.
FN = Fp tanф
FP = FL – FI
= [ (P1-P2) D2 – [ m ω2r ( ]
= 68730 – 19306
FP = 49.424 KN
FN = FP tanф = 10.96 KN
2) Thrust in the connecting rod.
FQ = = 50.62KN
3) Tangential force on the crank – pin
FT = FQ
4) Turning moment on the crank shift
T = Fr × r = 14.484 KN-m
2). A petrol engine with 100mm stroke and connecting rod length 200mm runs at
1800rpm.The reciprocating engine has a mass of 1kg and the piston rod is 80
mm diameter. At a point during the power stroke, the pressure on the piston 0.7
N/mm2, when it has moved 10mm from inner dead centre.
i) Net load on the gudgeon pin,
ii) Thrust in the connecting rod,
iii) Reaction between the piston and cylinder,
iv) The engine speed at which in the above values becomes zero
(Nov / Dec 2015, May /June 2016)
Given
N = 1800 rpm
r = 50mm = 0.05m
l = 200mm
D = 80mm
mR = 1 Kg
P = 0.7 N/mm2
x = 10mm
Solution :
13
STUCOR
STUCOR APP
= 188.52 rad /sec

1) Net load on the gudgeon pin
FP = FL – FI = 1840 N
FL = D2 × p = 3520 N
FI = mR ω 2 r = 1671 N
2) Thurst in the connecting rod
FQ = = 1866.3 N
3) Reaction between the piston and cylinder,
FN = FP tanф = 254 N
4) Engine speed at which the above values until become zero
FP = FL – FI
0 = FL – FI
FL = FI
m r (ω1)2 r = D2 P
ω12 = 74894 => ω1 = 273.6 rad/sec
N1 = 2612 rpm.
3). The turning moment diagram for a petrol engine is drawn to the following
scales: Turning moment, 1mm=5 N-m: crank angle, 1 mm=1°.The turning
moment diagram repeats itself at every half revolution of the engine and areas
above and below the mean turning moment line taken in order are 295, 685, 40,
340, 960, 270 mm2.The rotating parts are equivalent to a mass of 36 kg at a
radius of gyration of 150mm.Determine the coefficient of fluctuation of speed
when the engine runs at 1800r.p.m.
(Nov / Dec 2009, May/June 2009, Nov / Dec 2015)
Given
m=36kg
k =150mm = 0.15 m
N = 1800 rpm
ω = 188.52 rad/sec
Solution:
Scale :
1) Turning moment 1mm = 5N-m
2) Crank angle 1mm = 10
14
STUCOR
STUCOR APP
Moment .. . Turning moment = 5 x = = 0.08722 N-m
Turning
T mean
Where
Crank angle (θ)
A=E
B= E+295
C = E +295 – 685
D = E +295 – 685 + 40
E = E +295 – 685 + 40 – 340
F = E +295 – 685 + 40 – 340 +960
G = E +295 – 685 + 40 – 340 +960 – 270
Maximum energy at B = E+295
Minimum energy at E = E – 690
∆E = ( maximum energy ) – (minimum energy)
= (E+295) – (E – 690) [ 1mm2 = 0.0872 N-
m]
= 985 mm2
∆E = 985 × 0.0872 = 85.892 N-m
∆E = m k 2 ω 2 cs
85.892 = 36×0.522 × ((2π×1800)/60) × cs
Cs = 0.003 (or) 0.3%
4). A shaft fitted with a flywheel rotates at 250r.p.m and drives a machine. The
torque of machine varies in a cyclic manner over a period of 3 revolutions.
The torque rises from 750 N-m to 3000 N-m uniformly during ½ revolution
and remains constant for the following revolution. It then falls uniformly to
750N-m during the next ½ revolution and remains constant for one
revolution, the cycle being repeats thereafter. Determine the power required
to drive the machine and percentage fluctuation in speed, if the driving
torque applied to the shaft is constant and the mass of the flywheel is 500kg
15
STUCOR
STUCOR APP
with radius of gyration of 600mm.
(May/June 2014, Nov / Dec 2009)
Given
N = 250 rpm
M = 500Kg
K = 600 mm = 0.6m
ω= = 26.2 rad/s
Solution
Torque required for one complete cycle = Area of figure OABCDEF
= Area OAEF + Area ABG + Area BCHG + Area CDH
= ( OFx OA) + ½ (AGxBG)+(GHxCH) + ½ (HDxCH)
= 11250 Π N-m
T mean = = 1875 N.m.
B C
30
0
P
Turning moment N-
0
Tmean
L M N
D E
7
5 G H
0
F
2 3 4 5 6
π π π
π π π
(i) Power required to angle

Crank drive(θ)the machine
P = Tmean x ω = 49.125 KW
(ii) Total flucation of the Speed
From the Triangle ABG & LBM
=
LM = 1.570
16
STUCOR
STUCOR APP
From the Triangle NCP & HCD

=
NP = 1.570
From the Rectangle BMCN

BM = CN = 1125 N-m
∆E = Area LBCP
= Triangle LBM + Rectangle BMCN + Triangle CNP.
= ( ½ * LM * BM ) + ( BM * CN) + ( ½ * CN*NP)
= ( ½ *1.57 * 1125) + ( 1125 * 2π) + ( ½ * 1125*π)
∆E = 8837 N-m
∆E = m K2 ω 2 cs
Cs = 0.071 *100
Cs = 7.1%
5).The turning moment curve for an engine is represented by the equation,

T=(20000+9500 sin2θ-5700cos 2θ)N-m, where θ is the angle moved by the
crank from inner dead centre.
If the resisting torque is constant, find:
1. Power developed by the engine
2. Moment of inertia of flywheel in kg-m2, if the total fluctuation of speed is
not to exceed 1% of mean speed which is 180r.p.m and
3. Angular acceleration of the flywheel when the crank has turned through
45° from inner dead centre.
(Nov / Dec 2012, Nov / Dec 2014)
Given data:
T= (20000+9500 sin 2θ – 5700 cos2θ) N-m
N = 180rpm
ω = 18.85rad/sec
θ = 450
CS = 1% or 0.01
Solution :
Power developed by the engine work done per revolution =
=
17
STUCOR
STUCOR APP
= 40,000 Π N-m
Tmean = workdone per revolution / 2Π = 20,0000 N-m
P = T mean× ω = 377 KW.
Moment of inertia of flywheel (I) kg-m2

T = Tmean
(20000+9500 sin 2θ – 5700 cos2θ) = 20000
9500 sin 2θ – 5700 cos2θ = 20000 – 20000
9500 sin 2θ = 5700 cos2θ
sin 2θ / cos2θ = 5700 / 9500
tan 2θ = 0.6
2θ = tan-1 0.6
2θ = 30.96
θ = 30.96 / 2
θB= 15.480. ( θB = 15.5 , θC = 90+ 15.5 = 105.50 )
θB = 15.50 and θC = 105.50
∆E =
∆E = 11078 N-m
∆E = I ω2 Cs
11078 = I * 18.852 *0.01
I = 3121 Kg.m2
Angular acceleration of flywheel (α) ( θ =450)

T excess = T – Tmean
T excess = 9500 sin 2θ – 5700 cos2θ
T excess = I x α
9500 sin 2(45) – 5700 cos2(45) = 3121 * α
α = 3.044 rad/s2
PART-C
1. A vertical, single cylinder, single acting diesel engine has a cylinder
diameter300 mm, stroke length 500 mm, and connecting rod length 4.5
times the crank length. The engine runs at 180 r.p.m. The mass of the
reciprocating parts is 280 kg. The compression ratio is 14 and the pressure
remains constant during the injection of the oil for 1/10th of the stroke. If
the compression and expansion follows the law p.V1.35 = constant, find:1.
18
STUCOR
STUCOR APP
Crank-pin effort, 2. Thrust on the bearings, and 3. Turning moment on the
crank shaft, when the crank displacement is 45° from the inner dead centre
position during expansion stroke. The suction pressure may be taken as 0.1
N/mm2.
Solution.
Given : D = 300 mm = 0.3 m ;L = 500 mm = 0.5 m or r = 0.25 m ; l = 4.5 r
or n = l / r = 4.5; N = 180 r.p.m. or ω = 2π × 180/60 = 18.85 rad/s ; mR = 280 kg
V1/ V2= 14; θ = 45°; p1 = 0.1 N/mm2
The pressure-volume (i.e. p-V) diagram for a diesel engine is shown in Fig, in
which 1-2 represents the compression, 2-3 represents the injection of fuel, 3-4
represents the expansion, and 4-1 represents the exhaust.
Let
P1, P2, P3, and P4 = Pressures corresponding to points 1, 2, 3 and 4 respectively,
V1, V2, V3, and V4 = Volumes corresponding to points 1, 2, 3 and 4 respectively.
Since the compression follows the law PV 1.35 = constant, therefore
1.35 1.35
P1 (V1) = P2 (V2 ) or
P 2 = P1 (V1/V2) 1.35
= 0.1 x (14)1.35 = 3.526 N/mm2
We know that swept volume
V S = π / 4 x D2 = π / 4 x (0.3)2 x 0.5 = 0.035 m3
Since the injection of fuel takes place at constant pressure (i.e. p2 = p3) and
19
STUCOR
STUCOR APP
continues up to 1/10th of the stroke, therefore volume at the end of the injection of
fuel,
When the crank displacement is 45° (i.e. when θ = 45°) from the inner dead centre
during expansion stroke, the corresponding displacement of the piston (marked by
point 4' on the p-V diagram) is given by
Since the expansion follows the law P.V 1.35 = constant, therefore
Difference of pressures on two sides of the piston,
∴
Net load on the piston,
Inertia force on the reciprocating parts,
We know that net force on the piston or piston effort,
1. Crank-pin effort
Let φ = Angle of inclination of the connecting rod to the line of stroke.
20
STUCOR
STUCOR APP
We know that crank-pin effort
2. Thrust on the bearings
3. Turning moment on the crankshaft
21
STUCOR
STUCOR APP
UNIT II BALANCING
PART A
1. Differentiate: Static and Dynamic Balancing. (May „16), (Nov „12)
Static Balancing:-
The net dynamic force acting on the shaft is equal to zero. This requires that the
line of action of three centrifugal forces must be the same. This is the condition
for static balancing.
Dynamic Balancing:-
The net couple due to the dynamic forces acting on the shaft is equal to zero,
provides the condition for dynamic balancing.
2. What is meant by balancing of rotating masses? (May ' 16)

The process of providing the second mass in order to counteract the effect of the
centrifugal force of the first mass is called balancing of rotating masses.
3. State the reasons for choosing multi - cylinder engine in comparison with
that of the single cylinder engine. (Nov „15)
The multi - cylinder engine is choose in compassion with that of the single
cylinder engine because of
 Complete balancing of primary and secondary forces are possible
whereas
 In case of single cylinder engine, partial balancing alone is possible.
4. What do you mean by partial balancing single cylinder engine? (Nov „15)
The unbalanced force due to reciprocating masses (mω2r cos, and mω2r
cos2/n,) varies in magnitude because of  , but constant in direction while due
to the revolving masses, the unbalanced force is constant in magnitude but
rates in direction in known as partial balancing of single cylinder engine.
5. When is a system said to be completely balanced? (May „14)

Condition for complete balance
I. The resultant centrifugal force must be zero.
II. The resultant couple must be zero.
6. What is tractive force? (May “14)
It is the resultant unbalanced force due to the two cylinders along the line
of stoke.
7. Define swaying couple. (Nov “14)
22
STUCOR
STUCOR APP
The unbalanced forces along the line of stroke for the two cylinders
constitute a couple about the centre line YY between the cylinders.
This couple has swaying effect about a vertical axis, and tends to sway the
engine alternatively in clockwise and anticlockwise. This couple is known as
“swaying couple".
8. Define hammer blow in locomotives. (Ap/May 2017, Nov 16,

Nov‟13) It is defined as the maximum magnitude of the unbalanced force along
the perpendicular to the line of stroke.
9. How does firing order affect the balancing of incline multi cylinder engine?
(May‟11)
With respect to firing order, unbalanced primary and secondary couple
will vary in its magnitude and direction. Because firing order represents, the
position of an engine in plane position diagram. If position charges, respective
couple will vary.
10. Define the term shaking or unbalanced force.

It is defined as the resultant of all the forces acting on the body of the
engine due to inertia forces only is known as unbalanced force or shaking force.
Part B
1. A,B,C and D are four masses carried by a rotating shaft at radii 100 , 125,
200 and 150 mm respectively. The planes in which the masses revolve are
spaced 600 mm apart and the masses of B ,C and D are 10 kg, 5 kg and 4
kg respectively. Find the required mass A and the relative angular settings
of the four masses so that the shaft shall be in complete balance.
[NOV „ 12, May „ 14 ,NOV „ 15]
Given data:
rA = 100 mm = 0.1 m
rB= 125 mm = 0.125 m mB = 10 kg
rC = 200 mm = 0.2 m mC = 5 kg
rD = 150 mm = 0.15 m mD = 4 kg
To find:
23
STUCOR
STUCOR APP
 Mass of A (mA)
 Angular settings (˂BOA)
Solution:
The position of planes is shown in fig.
Plane Mass Radius Centrifuga Distance Couple † ω2

l force
(m) (r) from plane (mrl)
N A (l)
Kg m Kg m2
“m”
A mA 0.1 0.1 mA 0 0
B 10 0.125 1.25 0.6 0.75
C 5 0.2 1 1.2 1.2
D 4 0.15 0.6 1.8 1.08
Result :
24
STUCOR
STUCOR APP
a) Mass A mA= 7 kg
b) Angular setting A = 1550 (anticlockwise Direction)
(2).The following data apply to an outside cylinder uncoupled locomotive:
Mass of rotating parts per cylinder = 360Kg ;

Mass of reciprocating parts per cylinder = 300 kg
; Angle b/w cranks = 900 ; Crank radius = 0.3 m ;
Cylinder centers = 1.75 m ,
Radius of balance masses = 0.75 m, Wheel centres = 1.45 m.
If whole of the rotating and two- thirds of reciprocating parts are to
be balanced in planes of the driving wheels, find:
1. Magnitude and angular positions of balance masses,
2.speed in kilometres per hour at which the wheel will left off the rails
when the load on each driving wheel is 30 kN and the diameter of tread of
driving wheels is 1.8 m , and
3. swaying couple at speed arrived at in (2) above. (NOV '' 13)
Given data:
m1 = 360 kg, m2 = 300 kg ,
< AOD =900 , rA= rB = 0.3 m,
a = 1.75 m, rB=rC =0.75 m,
c = 2/3
To Find :
1. Magnitude and angular position of balance masses (i.e., mB,
mC & B ,C)
2. Speed (v)
3. Swaying couple
Solution:
Plane Mass Radius(r) Centrifugal Distance Couple

(m) m force from † ω2
Kg N plane (mrl)
A (l) Kg m2
“m”
A 560 0.3 168 -0.15 -25.2
B(R.P) mB 0.75 0.75 mB 0 0
C Mc 0.75 0.75 mc 1.45 1.08 mc
D 560 0.3 168 1.6 268.8
The equivalent mass of the rotating parts to be balanced per cylinder
m = mA = mD = m1 + c. m2
25
STUCOR
STUCOR APP
= 360+ (2/3) 300
= 560 kg
From fig (c) couple polygon, by measurement
1.08 mC = 269.6 kg - m2
mC = (269.6/1.08)
= 249 kg
From fig (d) couple polygon, by measurement
C = 2750
From Fig (d) Force polygon, the vector o represent the balancing force, by
measurement
0.75 mB = 186.75 kg - m
mB = 249 kg
From vector OB , by measurement
 B = 174.50
26
STUCOR
STUCOR APP
Determine of V:
Given P = 30 kN = 30×103 N, D = 1.8 m, Balancing masses mB =mC = 249 kg
Balancing mass for reciprocating parts,
B= ×249
= × ×249
= 89 kg
WKT
ω= = =21.2 rad/s
velocity = r ω = ×21.2 = 19.08 m/s =68.7 km/h
Determination of swaying couple:
swaying couple = ×m2r ω2
=16.68 KN-m
(3). A four crank engine has two outer cranks set at 120 0 to each other and their
reciprocating masses are each 400 kg. The distance between the planes of
rotation of adjacent cranks are 450 mm , 750 mm and 600 mm. if the engine
is to be in complete primary balance, find the reciprocating mass and the
relative angular position for each of the inner cranks.
If the length of each crank is 300 mm, the length of each connecting
rod is 1.2 m and the speed of rotation is 240 rpm.what is the maximum
secondary unbalanced force? (Nov '12 ,May '14)
Given data:
m1 = m4 = 400 kg ;
r = 0.3 m , l = 1.2 m, N = 240 rpm
ω= = 25.14 rad/s
To find:
27
STUCOR
STUCOR APP
1. Reciprocating mass, its relative angular position
2. Maximum secondary unbalanced force
Solution:
Let m2 & m3 = Reciprocating mass for then inner cranks 2 & 3 resp.
2 & 3 = Angular position of the cranks 2& 3 with respect to crank 1

resp.
STUCOR
STUCOR APP
m3
4 400 0.3 120 1.35 162
From Fig (c) the primary couple polygon, the reciprocating mass for crank 3 is
determined
0.225 mB = 196
mB = 871 kg
Its angular position wrt crank 1 in the counter clockwise direction is
3 = 3260
From fig (d) the primary force polygon the reciprocating mass for crank 2, is
determined as follows:
0.3 m2 = 284 kg-m
m2 = 947 kg
Its angular position wrt crank 1 in the counter clockwise direction is
2 = 1680
Determination of maximum secondary unbalanced force.
The secondary crank positions obtained by rotating the primary cranks at twice
the angle, is shown in fig(e).
The secondary force polygon is drawn to suitable scale providing the closing
side represents the maximum secondary unbalanced force.
Maximum secondary unbalanced force is

29
STUCOR
STUCOR APP
= 582× = 582×
= 91.96 × 103 N
Result :
1. The reciprocating mass m2 = 947 kg
m3= 871 kg
2. Its angular position 2 = 1680
3 = 3260
3. Maximum secondary unbalanced force is 91.9 kN
(4) The three cylinders of an air compressor have their axes 1200 to one
another, and their connecting rods are coupled to a single crank. The stroke
is 100 mm and length of each connecting rod is 150 mm. The mass of the
reciprocating parts per cylinder is 1.5 kg. Find the maximum primary and
secondary forces acting on the frame of the compressor when running at
3000rpm.(Nov '13)
Given data:
Stroke L = 100 mm = 0.1 m

Radius r = L/2 = 0.05 m
Length of connecting rod (l) = 150 mm
Mass of reciprocating parts per cylinder (m) = 1.5 kg
Speed N = 3000 rpm ; ω = = 314.2 rad/s

To find:
(1) Maximum primary force acting on the frame of the compressor
(2) Maximum secondary force acting on the frame of the compressor.
Solution:
The position of three cylinders is shown below
Let the common crank be along the inner dead centre of cylinder 1.
30
STUCOR
STUCOR APP
Since common crank rotates clockwise,  is  ve.
Determination of (i)
The primary direct and reverse crank positions are shown in Fig (b) and (c)
when  = 00 for cylinder 1, both the primary direct and reverse cranks will
coincide with the common crank.
when  = 1200 for cylinder 2, the primary direct crank is 1200

clockwise and the primary reverse crank is120 0 anticlockwise from the line of
stroke of cylinder 2.
when  = 2400 for cylinder 3, the primary direct crank is 240 0 clockwise and
the primary reverse crank is 2400 anticlockwise from the line of stroke of
cylinder 3.
From Fig (c) the primary reverse cranks form a balanced system.
There is no unbalanced primary force due to the reverse cranks.
From Fig (b) the resultant primary force is equivqlent to the centrifugal force of
mass 3 (m/2) attached to the end of the crank.
Maximum primary force = r
= 0.05
= 11.11 kN
31
STUCOR
STUCOR APP
The maximum primary force may be balanced by a mass attached diametrically
opposite to the crank pin and rotating with the crank of magnitude B1 at radius b1
B1b1 = r= 0.05
= 0.1125 Nm.
Determination of (ii)
The secondary direct and reverse crank position are shown in fig (a) & (b)
diagram given below
Maximum secondary force =
= 3702 N
Balanced by mass B2,
B2b2 = = 0.009Nm.
Result:
1) Maximum primary Force = 11.1kN
2) Maximum Secondary force = 3.7 kN.
(5) A vee - twin engine has the cylinder axes right angles and the connecting
rods operate a common crank. The reciprocating mass per cylinder is 11.5
kg and the crank radius is 15mm. The length of the connecting rod is 0.3 m.
show that the may be balanced for primary forces by means of a revolving
balance mass.
32
STUCOR
STUCOR APP
If the engine speed is 500 rpm. What is the value of maximum resultant
secondary force/ (Nov '15)
Given data:
2 = 900, = 450 , m = 11.5 kg , r = 75 mm = 0.075 m
l = 0.3 m ,N = 500 rpm, ω = = 52.37 rad/s
To Find:
Maximum resultant secondary force
Solution:
We known that the resultant primary force (FP)
FP = 2 m ω2r
= 2 m ω2r
FP = m ω2r
Since the resultant primary force m ω2r is the centrifugal force of mass m at the
crank radius "r" when rotating at ω rad/s
The engine may be balanced by a rotating balanced mass.
Maximum resultant secondary force:
WKT, theresultant secondary force (FS)
FS = r sin 2 (when 2 = 900)
sin 2 = 1 ( Maximum)
  = 450 or 1350
 FS = r=
= 836 N
Result: The maximum secondary resultant force = 836 N
33
STUCOR
STUCOR APP
PART-C
1. A shaft has three eccentrics, each 75 mm diameter and 25 mm thick, machined
in one piece with the shaft. The central planes of the eccentric are 60 mm
apart. The distance of the centres from the axis of rotation is 12 mm, 18 mm
and 12 mm and their angular positions are 120° apart. The density of metal is
7000 kg/m3. Find the amount of out-of-balance force and couple at 600 r.p.m. If
the shaft is balanced by adding two masses at a radius 75 mm and at distances
of 100 mm from the central plane of the middle eccentric, find the amount of
the masses and their angular positions.
Solution.
Given : D = 75 mm = 0.075 m ; t = 25 mm = 0.025 m ; rA = 12 mm = 0.012 m ;
rB = 18 mm = 0.018 m ; rC = 12 mm = 0.012 mm ; ρ = 7000 kg/m3 ; N = 600 r.p.m.
ω = 2π × 600/60 = 62.84 rad/s ; rL = rM = 75 mm = 0.075 m
We know that mass of each eccentric,
Let L and M be the planes at distances of 100 mm from the central plane of middle
eccentric. The position of the planes and the angular position of the three eccentrics
is shown in Fig. (a) and (b) respectively. Assuming L as the reference plane and
mass of the eccentric A in the vertical direction, the data may be tabulated as below :
34
STUCOR
STUCOR APP
Out-of-balance force
The out-of-balance force is obtained by drawing the force polygon, as shown in Fig. (c), from
the data given in Table (column 4). The resultant oc represents the out-of-balance force.
Since the centrifugal force is proportional to the product of mass and radius (i.e. m.r),
therefore by measurement.
Out-of-balance force = vector oc = 4.75 × 10–3 kg-m
Out-of-balance couple
The out-of-balance couple is obtained by drawing the couple polygon from the data
given in Table (column 6), as shown in Fig. (d). The resultant o′c′ represents the out-of
balance
couple. Since the couple is proportional to the product of force and distance (m.r.l), therefore
by measurement,
Out-of-balance couple = vector o′c′ = 1.1 × 10–3 kg-m2
Amount of balancing masses and their angular positions

The vector c′o′ (in the direction from c′ to o′ ), as shown in Fig. (d) represents the
balancing couple and is proportional to 15 × 10–3 mM, i.e.
35
STUCOR
STUCOR APP
In order to find the balancing mass (mL), a force polygon as shown in Fig. (e) is
drawn. The closing side of the polygon i.e. vector do (in the direction from d to o) represents
the balancing force and is proportional to 75 × 10–3 mL. By measurement, we find that
75 × 10–3 mL = vector do = 5.2 ×10–3 kg-m
mL = 0.0693 kg
Draw OL in Fig. (b), parallel to vector do. By measurement, we find that the angular
position of mass (mL) is 124° from mass A in the clockwise direction.
36
STUCOR
STUCOR APP
UNIT III SINGLE DEGREE FREES VIBRATION
PART – A
1. What are the different types of vibratory motions? (May/June 2016)

1. Free vibrations
a) Longitudinal vibration, b) Transverse vibration, and c) Torsional
vibration.
2. Forced vibrations, and
3. Damped vibration.
2. Define degree of freedom in Vibrating systems?

The number of independent co-ordinates required to completely define the
motion of the system is known as degree of freedom of system.
3. List out the various methods of finding the natural frequency of free
longitudinal vibrations. (Nov/Dec 2005)
1. Energy method,
2. Equilibrium method and
3. Rayleigh‟s method.
4. Distinguish between critical damping and large damping. (Nov/Dec 2006)

If system is critically damped, the mass moves back very quickly to its
equilibrium position within no time. Whereas in large damping, the mass moves
slowly to the equilibrium position.
5. Define critical or whirling or whipping speed of a shaft. (May/June 2016)

The speed at which resonance occurs is called critical speed of the shaft.
In other words, the speed at which the shaft runs so that the additional deflection
of the shaft from the axis of rotation becomes infinite is known as critical speed.
6. Give the limit beyond which damping is detrimental. Why?

(May/June 2013)
When damping factor ξ > 1, the aperiodic motion is resulted. That is,
aperiodic motion means the system cannot vibrate due to over damping. Once
the system is disturbed, it will take infinite time to come back to equilibrium
position.
7. Define damping ratio or damping factor. (Nov/Dec 2013)

It is defined as the ratio of actual damping coefficient to the critical
damping coefficient.
37
STUCOR
STUCOR APP
Damping factor = =
8. Define logarithmic decrement. (May/June 2016)

Logarithmic decrement is defined as the natural logarithm of the
amplitude reduction factor. The amplitude reduction factor is the ratio of any
two successive amplitudes on the same side of the mean position.
9. Determine the natural frequency of mass of 10kg suspended at the bottom

of the two springs (of stiffness 5N/mm and 8 N/mm) in series.
(May/June 2013)
Given:
Mass m = 10kg;
S1= 5N/mm;
S2= 8N/mm
Solution:
Equivalent spring stiffness Seq= S1+ S2=5 + 8= 13N/mm
Natural Frequency fn =
= = 5.74 Hz
10. Define torsional equivalent shaft.

A shaft having variable diameter for different lengths can be theoretically
replaced by an equivalent shaft of uniform diameter such that they have the same
total angle of twist when equal opposing torques are applied at their ends. Such
a theoretically replaced shaft is known as torsionally equivalent shaf
PART – B
1. A vertical shaft of 5 mm diameter is 200 mm long and is supported in long

bearings at its ends. A disc of mass 50 kg is attached to the center of the
shaft. Neglecting any increase in stiffness due to the attachment of the disc
to the shaft, find the critical speed of rotation and the maximum bending
stress when the shaft is rotating at 75% of the critical speed. The center of
the disc is 0.25 mm from the geometric axis of the shaft. E = 200 GN/m2.
38
STUCOR
STUCOR APP
(Nov/Dec 2014, May/June 2013)
Given:
d = 5 mm = 0.005
m; l = 200 mm = 0.2
m; m = 50 kg;
e = 0.25 mm = 0.25 × 10–3 m;
E = 200 GN/m2 = 200 × 109 N/m2
To find:
Critical speed of rotation
Maximum bending stress
Solution:
We know that moment of inertia of the shaft,
= = 30.7 X 10 -12 m4
Since the shaft is supported in long bearings, it is assumed to be fixed at

both ends. We know that the static deflection at the centre of the shaft due to a
mass of 50 kg,
δ=
= 3.33 X m
We know that critical speed of rotation (or natural frequency of transverse

vibrations),
Nc =
= 8.64 r.p.s
Maximum bending stress

Let ζ= Maximum bending stress in N/m2, and
N = Speed of the shaft = 75% of critical speed = 0.75 Nc . . . (Given)
When the shaft starts rotating, the additional dynamic load (W1) to which
the shaft is subjected, may be obtained by using the bending equation,
= (or) M =
39
STUCOR
STUCOR APP
We know that for a shaft fixed at both ends and carrying a point load
(W1) at the centre, the maximum bending moment
M=
W1 = )= x
= 0.49 x ζN
Additional deflection due to load W1,
y= (δ) = X 3.33X10-3
= 3.327 X 10-12
y= =
3.327 X 10-12 ζ = =
= 0.0962 N/m2 (Taking +ve Sign)
= 96.2 x 106 N/m2
96.2 MN/m2
2. Derive the expression for the natural frequency of free transverse or

longitud inal vibrations by using any two methods. (May/June 2016)
i. Equilibrium Method
Consider a constraint (i.e. spring) of negligible mass in an unstrained position, as
shown in Figure
Let s = Stiffness of the constraint. It is the force required to produce unit d
isplacement in the direction of vibration. It is usually expressed in N/m.
m = Mass of the body suspended from the constraint in kg
W = Weight of the body in newtons = m.g,
δ= Static deflection of the spring in metres due to weight W newtons, and
40
STUCOR
STUCOR APP
x = Displacement given to the body by the external force, in metres.
Restoring force =W - s (δ + x) =W - s.δ - s.x
= s.δ - s.δ - s. x = -s.x (since W = s.δ). . (i)

(Taking upward force as negative)
And Accelerating force = Mass × Acceleration = m x .... (ii)
(Taking downward force as +ve)
Equating Restoring force and accelerating force
mx = -s.x
mx + s.x = 0
+ .x = 0........(iii)
We know that the fundamental equation of simple harmonic motion

is
+ .x = 0.......(iv)
Time period, tp = = 2π
Natural frequency, fn = = =
41
STUCOR
STUCOR APP
Taking the value of g as 9.81 m/s2 and δ in metres,
fn = = Hz
ii) Energy Method:
The kinetic energy is due to the motion of the body and the potential energy is
with respect to a certain datum position which is equal to the amount of work
required to move the body from the datum position.
In the case of vibrations, the datum position is the mean or equilibrium position
at which the potential energy of the body or the system is zero. In the free
vibrations, no energy is transferred to the system or from the system. Therefore
the summation of kinetic energy and potential energy must be a constant quantity
which is same at all the times.
K.E = ;
P.E = x=
=0
+ =0
The time period and the natural frequency may be obtained as

discussed in the previous method.
3). A machine of mass 75 kg is mounted on springs and is fitted with a dashpot

to damp out vibrations. there are three springs each of stiffness 10 N/mm and
it is found that the amplitude if vibrations diminishes from 38.4 mm to 6.4 mm
in two complete oscillations. Assuming that the damping force varies as the
velocity, determine: 1.The resistance of the dash pot at unit velocity; 2.The
ratio of the frequency of the damped vibration to the frequency of the
undamped vibration; and 3.The periodic time of the damped vibration.
(May/June 2013)
42
STUCOR
STUCOR APP
Given:
m = 75 kg;
s = 10 N/mm = 10 ×103 N/m ;
x1 = 38.4 mm = 0.0384 m ;
x3 = 6.4 mm =0.0064 m
Solution:
Since the stiffness of each spring is 10 × 103 N/m and there are 3 springs,
therefore total stiffness,
s = 3×10×103 = 30×103 N/m
Natural circular frequency of motion,
a. Resistance of the dashpot at unit velocity
Let
x2 = Amplitude after one complete oscillation in metres, and
x3 = Amplitude after two complete oscillations in metres.
c = Resistance of the dashpot in newtons at unit velocity i.e. in N/m/s,
43
STUCOR
STUCOR APP
Squaring on both sides:
0.8 =
= 7.94
a=2.8
a=c/2m
c=2am=2(2.8) (75) =420N/m/s
b. Ratio of the frequency of the damped vibration to the frequency of

undamped vibration
Let
= Frequency of damped vibration

=
= Frequency of damped vibration

=
= 0.99
c. Periodic time of damped vibration (tp)
= = = = 0.32s
4).The mass of a single degree damped vibrating system is 7.5 kg and makes 24
free oscillations in 14 seconds when disturbed from its equilibrium position.
The amplitude of vibration reduces to 0.25 of its initial value after five
oscillations. Determine: 1.Stiffness of the spring 2.Logarithmic decrement, and
3.damping factor, i.e. the ratio of the system damping to critical damping.
(Nov/Dec 2012)
Given:
m = 7.5 kg
44
STUCOR
STUCOR APP
Solution:
Since 24 oscillations are made in 14 seconds, therefore frequency of free vibrations,
fn = 24/14 = 1.7
n = 2π× fn = 2 π ×1.7 = 10.7 rad/s
a. Stiffness of the spring
Let s = Stiffness of the spring in N/m.
or s = = 10.72(7.5) = 860 N/m
b. Logarithmic decrement
Let x1 = Initial amplitude,
x6 = Final amplitude after five oscillations = 0.25 x1
= 4 1/5 = 1.32
Logarithmic decrement:
c. Damping factor
Let c = Damping coefficient for the actual system, and
cc = Damping coefficient for the critical damped system.
Logarithmic decrement (δ):
0.28 = =
0.0784 = (Squaring on both sides)

45
STUCOR
STUCOR APP
8.977 – 0.0784a2 = 39.5a2
a2 = 0.227
a = 0.476
Damping coefficient for the actual system (c):
a = c / 2m or c = a x 2m = 0.476 x 2 x 7.5 = 7.2 N/m/s
Damping coefficient for the critical damped system (cc):
cc = 2mn = 2 x 7.5 x 10.7 = 160.5N/m/s
Damping Factor = = 7.2 / 160.5 = 0.045
5). A steel shaft 1.5 m long is 95 mm in diameter for the first 0.6 m of its length,
60 mm in diameter for the next 0.5 m of the length and 50 mm in diameter for
the remaining 0.4 m of its length. The shaft carries two flywheels at two ends,
the first having a mass of 900 kg and 0.85 m radius of gyration located at the 95
mm diameter end and the second having a mass of 700 kg and 0.55 m radius of
gyration located at the other end. Determine the location of the node and the
natural frequency of free torsional vibration of the system. The modulus of
rigidity of shaft material may be taken as 80 GN/m2.
(May/June 2016 model)
Given:
L = 1.5 m,
d1= 95mm,
l1=0.6 m, d2 =60mm,
l2 = 0.5m, d3 = 50 mm,
l3 = 0.4m, mA= 900kg,
KA = 0.85m,
mB = 700kg,
KB = 0.85m,
C = 80 X 109N/m2
46
STUCOR
STUCOR APP
Solution:
a. Equivalent shaft Diagram:
4 4
4 4
b. Location of the node:
= = 650Kgm2
= = 212Kgm2
= = = 0.326
Also,
47
STUCOR
STUCOR APP
Hence the node lies at 2.2m from flywheel A on the equivalent shaft.
c. Position of the node on the original shaft:
4
=
4
=
Position of the node on the original shaft = 0.855m
Natural frequency of free torsional vibrations J = = 0.0954= 8 x 10-6 m4
Natural frequency
= = =3.37 Hz
Part C
(1) A vertical steel shaft 15 mm diameter is held in long bearings 1 metre apart
and carries at its middle a disc of mass 15 kg.the eccentricity of the centre of
gravity of the disc from the centre of the rotor is 0.30 mm.
The modulus of elasticity for the shaft material is 200 GN/m2 and the
permissible stress is 70 MN/m2. Determine : 1.The critical speed of the shaft
and 2. The range of speed over which it is unsafe to run the shaft. Neglect the
mass of the shaft.
48
STUCOR
STUCOR APP
{ For a shaft with fixed end carrying a concentrated load (W) at the centre δ =
, and M = where δ and M are maximum deflection and bending

moment respectively}
Given:
d = 15 mm = 0.015 m;
l = 1m;
m = 15 kg;
e = 0.3 mm = 0.3 × 10–3 m;
E = 200 GN/m2 = 200 × 109 N/m2
ζ = 70 MN/m2 = 70 × 106 N/m2
To find:
Critical speed of shaft
Range of speed
Solution:
We know that moment of inertia of the shaft,
Since the shaft is held in long bearings, it is assumed to be fixed at both

ends. We know that the static deflection at the centre of the shaft.
Natural frequency of transverse vibrations,.
We know that critical speed of rotation (or natural frequency of transverse

vibrations),
49
STUCOR
STUCOR APP
Range of speed
Let N1 and N2 = Minimum and Maximum speed respectively.

When the shaft starts rotating, the additional dynamic load (W1) to which the shaft is
subjected, may be obtained by using the bending equation,
We know that
50
STUCOR
STUCOR APP
Hence the range of speed is from 718 r.p.m to 843 r.p.m.
51
STUCOR
STUCOR APP
UNIT – IV FORCED VIBRATION
PART- A
1. Define isolation factor. [Nov2012]
 It is defined as the ratio of the force transmitted (FT) to the force
applied (F) of the spring support.
 It is also known as “Transmissibility ratio”.
 It is denoted by the Greek letter “ε” (epsilon).
2. Write down the expression for amplitude of forced vibration. [Nov2012]

The amplitude of the forced vibration is given by
xmax  F
(C 2 2 (S  m 2 )2 )
Where F = Centrifugal force or the static force,

C = Damping Resistance,
ω = Angular velocity,
m = Mass of the body,
S = Stiffness.
3. Define step input and harmonic forcing function. [Nov 2013]

 It is defined as the constant force applied to the mass of a
vibrating system.
 The equation of motion mx  Sx  F
is
 The harmonic forcing function is given F(t)  Fo sin(t)
by
4. Define magnification factor as applied to forced vibration.

[May 2014, May 2016]
 It is the ratio of maximum displacement of the forced
vibration (xmax) to the deflection due to the static force F (xo).
 It is also known as dynamic magnifier.
5. List out the sources of the excitation in forced vibration. [May 2014]
a) Periodic forces like harmonic and non-harmonic,
b) Impulsive forces, and
c) Random forces like seismic waves.
STUCOR
STUCOR APP 52
STUCOR
STUCOR APP
6. Define the term “Logarithmic decrement” as applied to damped vibration.
[Nov 2014]
It is defined as the natural logarithm of the amplitude reduction factor.
The amplitude reduction factor is the ratio of any two successive amplitudes on
the same side of the mean position.
7. Classify vibration. [Nov 2015]

Vibration is classified into two types:
1. Free vibration, and
2. Forced vibration.
Further the free vibration is classified into
a) Longitudinal vibration,
b) Transverse vibration, and
c) Torsional vibration.
8. Define whirling speed. (Nov/Dec 2012)

The speed at which the shaft runs so that the additional deflection of the
shaft from the axis of rotation becomes infinite is known as whirling or critical
speed.
Mathematically,
S g
n  C  m 

9. Define damping ratio. (May/June 2014)

The ratio of the actual damping coefficient (C) to the critical damping
coefficient (Cc) is known as damping ratio or damping factor.
Mathematically,
Damping factor C C
= 
CC 2mn
10. What is meant by forced vibration? [May 2016]

When the body vibrates under the action of external force, then the body
is said to be under forced vibration. The external force applied to the body is
periodic disturbing force created by unbalance.
53
STUCOR
STUCOR APP
PART – B
1. A single cylinder vertical petrol engine of total mass of 200Kg is mounted
upon a steel chassis frame and causes a vertical static deflection of 2.4mm.
the reciprocating parts of the engine has a mass of 9Kg and move through a
vertical stroke of 160mm with SHM. A dashpot is provided whose damping
resistance is directly proportional to the velocity and amounts to 1.5
KN/mm/s , calculate at steady state
a) The amplitude of forced vibrations at 500 rpm engine speed, and
b) The speed of the driving shaft at which resonance will occur.
[Nov 2015, May 2016]
Given data
Mass of petrol engine m = 200 kg,
Deflection δ = 2.4 mm,
Mass of reciprocating parts m1 = 9 kg,
Stroke l = 160
mm,
Damping resistance C = 1
N/mm/s, Speed N = 500 r.p.m.
To find
a) The amplitude of forced vibrations at 500 rpm engine speed (xmax), and
b) The speed of the driving shaft at which resonance will occur (N).
Solution
a) Determination of xmax
The amplitude of the forced vibration is given by
xmax  F
(C22 (S  m2 )2 )
Where
F = Centrifugal force or the static force,
F = m1  2 r = 9 X 52.32X(l/2) = 24.6X103X(160/2)
F = 1.97 MN
C = Damping Resistance = 1 N/mm/s
ω = Angular velocity = (2πN/60) = 52.3
rad/s m = Mass of the body = 9 kg
S = Stiffness = (m . g)/ δ = 981 N/mm
Substituting all the values in the above equation, we get

Xmax = 6 mm
54
STUCOR
STUCOR APP
b) Determination of N
Let N be the speed of the driving shaft at which resonance occurs in r.p.m.
wkt, the angular speed at which resonance occurs
S g
n  C  m 

981X103
n  C  240  63.9rad / s
wkt,
2
N  63.9
60
N = 610 r.p.m
Result
a) The amplitude of forced vibrations at 500 rpm engine speed (xmax) = 6 mm,
and
b) The speed of the driving shaft at which resonance will occur (N) = 610 rpm.
2. A mass of 10 kg is suspended from one end of helical spring, the other end is
being fixed. The stiffness of the spring is 10 N/mm. The viscous damping
causes the amplitude to decrease to one-tenth of the initial value in four
complete oscillations. If a periodic force of 150 Cos 50t (N) is applied at the
mass in the vertical direction, find the amplitude of the forced vibrations.
What is its value of resonance? [Nov 2014]
Given data
Mass m = 10 kg,
Stiffness δ = 10 N/mm = 10x103 N/m
X5 = x1 /10 (since amplitude decreases to one-tenth of initial value in 4
complete oscillations).
Periodic force Fx = 150 Cos 50 t = F Cos ωt
Static force F = 150 N,
Angular velocity ω = 50 rad/s.
To find
a). Amplitude of the forced vibrations (xmax), and
b). Resonance value (xmax)
55
STUCOR
STUCOR APP
Solution
wkt, the angular speed at which resonance occurs
S g
n  C  m 

n  C  10X103  31.6rad / s
10
Since the amplitude decreases to 1/10th of the initial value in 4 complete
oscillations, therefore the ratio of initial amplitude (x1) to the final amplitude
after 4 complete oscillations (x5) is given
4
by
X X X X X X  X X
1
 1
. 2
. 3
. 4
 1 since = 2

X5 X2 X3 X4 X X2 X2 X3
5

 
X 1 =  X 1  14 = X 1  1 1
 4 =(10) 4
X 2  X 5  X1 
1/10
 
X1
 1.78
X2
wkt
 X1  2
loge  =a*
X 2 
(n 2  a 2
2a
loge 1.78 =
(31.6 2  a 2
2a
0.576 =
1000  a 2
a = 2.87
wkt
a = c 2m
c = 2ma = 2 X 10X 2.87
c = 57.74 N/m/s
Deflection of the system produced by the static force F
F
X0 = 150X103
S  10 0.015m
wkt , amplitude of the forced vibration is
xmax  F
(C 22 (S  m2 )2 )
Substituting the values we get xmax = 9.8mm
STUCOR
STUCOR APP 56
STUCOR
STUCOR APP
b) Determination of xmax at resonance
wkt , the amplitude of forced vibrations at resonance,
xmax = X0 S
c n
10X103
=
0.015* 57.54X 31.6
xmax = 82.2mm
Result
Amplitude of the forced vibration is 9.8mm,
Amplitude of the forced vibration at resonance is 82.2mm.
3). A machine part of mass 2kg vibrates in a viscous medium. Determine the
damping coefficient when a harmonic exciting force of 25N results in resonant
amplitude of 12.5mm with a period of 0.2seconds. if the system is excited by a
harmonic force of frequency 4Hz what will be the percentage increase in the
amplitude of vibration when damper is removed as compared with that damping.
[NOV 2014]
Given data
Mass = 2 Kg
Force = 25 N
Resonant Xmax =12.5mm
Time period tp = 0.26
Frequency f = 4 Hz.
To find
Damping coefficient (C)
Percentage increase in amplitude.
Solution
a). Determination of C
Let C = damping Coefficient in N/m/s
wkt, Natural circular frequency of the exciting force
2 2
n   0.2  31.42 rad/s
tp
wkt, the maximum amplitude of vibration at resonance
xmax = F
c n
0.0125 = 25
c*
STUCOR
3STUCOR APP
1
.
4
2
5
7
STUCOR
STUCOR APP
c = 63.7 N/m/s
b). Determination of % increase in amplitude
Exciting frequency (f) = 4Hz
Circular frequency ω = 2πf = 25.14 rad/s
wkt, the maximum amplitude of vibration with damping,
xmax  F
(C22 (S  m2 )2 )
25

((63.72 X 25.142 )  ((2x31.42  2x25.142 )2 )
xmax = 0.0143 m
The maximum amplitude of vibration when damper is removed
xmax = F
m[ 2
2
n
]
= 0.035m
Therefore, percentage increase in amplitude = 35.2  14.3
14.3  1.46 or
= 146%
Result
Damping coefficient is 63.7 N/m/s
Percentage increase in amplitude is 146%
4). A machine has a total mass of 90Kg and unbalanced reciprocating parts of
mass 2Kg which moves through a vertical stroke of 100mm with SHM. The
machine is mounted on four springs. The machine is having only one degree of
freedom and can undergo vertical displacement only. Calculate
(i). The combined stiffness is the force transmitted to the foundation is one
thirteenth of the applied force. Neglect damping and take the speed of rotation of
the machine crank shaft as 1000 r.p.m. when the machine is actually supported on
the springs, it is found that the damping reduces the amplitude of the successive
free vibrations by 30%. Find (ii). The force transmitted to the foundation at 900
r.p.m. [NOV 2015]
Given data
Total mass of machine (m1 ) = 90Kg
Unbalanced reciprocating parts mass(m2) = 2 Kg
Stroke length (l) = 100mm = 0.1m
Transmissiblity (or) isolation factor (ε) = 1/30
Speed (N) = 1000 r.p.m
Angular velocity (ω) 2N
 104.7rad / s
= 60
STUCOR
STUCOR APP 58
STUCOR
STUCOR APP
To find
i) Combined stiffness of springs (S),
ii) Force transmitted to the foundation at 1000r.p.m,
Solution
(i)Determination of stiffness of the spring
2
Transmissibility ε = n
2   2
n
2
1 
n
 2
30 104.72  
n
2
104.7 – ωn2 = 30 ωn2
31 ωn2= 104.72
ωn = 18.8 rad/s
wkt,
S S
ωn =  90
m1
S = 18.82 x 90
S = 31.78 x 103 N/m
(ii) Determination of FT
Since the damping reduces the amplitude of successive free vibrations by 30% .
therefore the final amplitude of vibration
x2 = 0.70x1
 X1  2
loge  =a*
X2 (n 2  a 2
 X1  2a
loge
0.704  =
(18.82  a2
2a
loge (1.42) =
353.4  a2
Solving we get
a = 0.45
wkt,
c = a*2m1 = 0.45 *2*90
c = 81 N/m/s
critical damping coefficient cc = 2mωn = 2 x 90 x 18.8
cc= 3384 N/m/s
59
STUCOR
STUCOR APP
Therefore actual value of transmissibility ratio (ε)
2
 2c 
1  c  
2 c n 
ε=  2c  
2
2
   1   2
 cc n   n 
1.104
ε=  0.044
25.08
wkt, the maximum unbalanced force on the m/c due to reciprocating parts
F = m2ω2r = 2 x 104.72 x (0.1/2)
F = 1096.2 N
Force transmitted to the foundation
FT = εF = 0.044 x 1096.2
FT = 48.23 N
RESULT:
i) Combined stiffness of springs is 31780 N/m
ii) Force transmitted to the foundation at 1000r.p.m is 48N.
5). Derive the equation of vibration isolation factor or transmissibility ratio

[MAY 2016]
The ratio of the force transmitted (FT) to the force applied (F) is known as the
transmissibility ratio of the spring support.
The force transmitted to the foundation consists of the following two forces:
(i) spring force or elastic force = S.xmax and
(ii) Damping force = cωxmax
The forces are perpendicular to each other therefore
FT = (S.x max ) 2  (c xmax )2
= xmax (S 2  (c)2 )
Transmissibility ratio or isolation factor is
FT
ε= = xmax S 2  (c)2
F
F
wkt, xmax = x0 * D = F * D
S
εD
=
S 2  c22
S
=D since c  2c

ε = Dc22
1 S ccn
S2
STUCOR
 2c 2
1  
DOWSNTULCOORAADPPED FROM c  c n 
STUCOR APP
60
STUCOR
STUCOR APP
wkt the magnification factor
1
D=
 2c 2   2 2
   1  2 
 ccn   n 
Substitute the magnification factor in „ε‟ we get
2
 2c 
1  c  

2 c n 
ε=  2c  
2
2
   1   2 
 c c n   n 
when the damper is not provided , then c=0 and
1
ε=

1    
2
 n 
 
from above, when    >1 ε is negligible i.e there is a phase difference of 180
 n 
degree between the transmitted and the disturbing force (Fcosωt).
PART C
(1) Define „ Dynamic Magnifier‟ and derive the relationship for the
dynamic magnifier.
It is the ratio of maximum displacement of the forced vibration (x max) to the
deflection due to the static force F (x0). We have proved in the previous article that
the maximum displacement or the amplitude of force vibration,.
61
STUCOR
STUCOR APP
Fig : Relationship between magnification factor and phase angle for different values
of ω/ ωn.
Magnification factor or Dynamic magnifier,
The magnification factor or dynamic magnifier gives the factor by which the
static deflection produced by a force F must be multiplied in order to obtain
the maximum amplitude of the forced vibration by the harmonic force F
cos ω.t.
From the Fig shows the relationship between the magnification factor (D) and
62
STUCOR
STUCOR APP
phase angle ɸ for different value of ω/ ωn. and for the values of damping factors
Notes: 1. If there is no damping (i.e. if the vibration is undamped),then c= 0,In that

case, magnification factor
2. At resonance ω = ωn.therefore magnification factor
63
STUCOR
STUCOR APP
UNIT V MECHANISM FOR CONTROL
PART A
1. Define sensitiveness of governors. [NOV/DEC 2014]

The sensitiveness is defines as the ratio of the mean speed to the
difference between the maximum and minimum speeds.
Sensitiveness = N/N1 – N2 = 2(N1 + N2)/ (N1 – N2)
N1 – Max Speed : N2 – Min Speed
2. What is meant by isochronous condition in governors? [MAY/JUNE 2013]

A governor with zero range of speed is known as an isochronous
governor. Actually the isochronisms are the stage of infinite sensitivity. i.e.,
when the equilibrium speed is constant for all radii of rotation of rotation of the
balls within the working range, the governor is said to be in isochronisms.
3. What is meant by hunting? [NOV/DEC 2015]

The phenomenon of continuous fluctuation of the engine speed above and
below the mean speed is termed as hunting. This occurs in over-sensitive
governors.
4. Differentiate the functions of flywheel and governor. [APRIL/MAY 2015]
S.no Flywheels Governors
1 The function of flywheel is to Its function is to control the

reduce the fluctuations of speed mean speed a period for output
during a cycle above over and load variations
below the mean value for
constant load from the prime
mover.
2 It works continuously from cycle Its works intermittently i.e. only

to cycle. when there is change in the
load.
3 It has no influence on mean It has no influence over cyclic

speed of the prime mover. speed Fluctuations
64
STUCOR
STUCOR APP
5. Define coefficient of sensitiveness in governors
It is the ratio between range of speed and mean speed
N1  N 2
Coefficient of sensitiveness = range of speed/ mean speed
N
=
6. What is meant by gyroscopic couple? [MAY/JUNE 2014]

If a body having moment of inertia I and rotating about its own axis at ω
rad/s is also caused to turn at ωp rad/s about an axis perpendicular to the axis of
spin, then it experiences a gyroscopic couple of magnitude (1.ω. ωp) in an axis
which is perpendicular to both the axis of spin and axis of precession.
7. Why there is no effect of the gyroscopic couple acting on the body of a

ship during rolling?
For the effect of gyroscopic couple to occur, the axis of procession
should always be perpendicular to the axis of the spin. In case of rolling of a
ship, the axis of precession is always parallel to the axis of spin for all positions.
Hence there is no effect of the gyroscopic Couple acting on a body of the ship
during rolling.
8. Discuss the effect of the gyroscopic couple on a 2 wheeled vehicle when

taking a turn. [NOV/DEC 14,
15]
The gyroscopic couple will act over the vehicle outwards. The tendency
of this couple is to overturn the vehicle in outward direction.
9. The engine of an aero plane rotates in clockwise direction when seen from
the tail end and the aero plane takes a turn to the left. What will be the
effect of the gyroscopic couple on the aero plane? [MAY/JUNE 2016]
The effect of gyroscopic couple will be to raise the nose and dip the tail.
10. What is the effect of friction on the governors? [NOV/DEC 2005]

The effect of friction on the governors is to increase the range of speed ,
governor effort and power of the governor
STUCOR
STUCOR APP 65
STUCOR
STUCOR APP
PART B
1) A spring loaded governor of the hartnell type has equal arms. The balls rotate
in a circle of 15 cm diameter when the sleeve is in the mid position and the ball
arms are vertical. The equilibrium speed for this position is 500rpm.the maximum
sleeve movement is to be 3cm and the maximum variation of speed taking in
account the friction to be ±5% of the mid position speed. The mass of the sleeve is
5kg and the friction force may be considered to arise out of an equivalent 3kg mass
at the sleeve. The power of the governor must be sufficient to overcome the friction
by 1% change of speed either way from mid position. Determine:
i) The rotating masses
ii) The spring stiffness
iii) The initial compression of the spring, neglect the obliquity
effect of arms. [APRIL/MAY 2015]
Given data:
x=y,d=150mm=0.15m, N = 500 rpm, h=30mm, M=5kg, F=3*9.81= 29.43 N
To find:
Mass (m),spring stiffness(S), initial compression of the spring.
Solution:
(i) Mass of each rotating balls (m)
=
= 52.34 rad/sec
Since the change of speed at mid position to overcome friction is
1%. Minimum speed at mid position.
1= ω – 0.01ω = 0.99ω
= 0.99 ω = 0.99(52.34) =51.81

Maximum speed at mid position
1= ω + 0.01ω = 1.01ω
= 1.01 ω = 1.01(52.34) =52.86

Therefore centrifugal force at the minimum speed
Fc1 = mω2r = m(51.81)2(0.075)
=201.32 m
Fc2 = mω2r = m(52.86)2(0.075)
=209.56 m
For minimum speed at mid position,
S + (M.g - F) = 2 Fc1 (x/y)
S +[(5*9.81)-29.43] = 2(201.32 m)(1) [since x/y =1]
S = 402.64 m – 19.62-------------------[1]
66
STUCOR
STUCOR APP
For maximum speed at mid position,
S + (M.g + F) = 2 Fc1 (x/y)
S +[(5*9.81)+29.43] = 2(209.56 m)(1) [since x/y =1]
S = 419.12 m – 78.48-------------------[2]
By solving [1] & [2]

S = 402.64 m – 19.62
S = 419.12 m – 78.48
=-16.48 m + 58.68
58.68 =16.48 m
m =3.56 kg
(ii) Spring stiffness (s)
Since maximum speed variation, considering friction is ± 5% of the mid position
speed.
Therefore minimum speed considering friction
1= ω – 0.05ω = 0.995ω
=0.95 (52.34)=49.72
Maximum speed considering friction
2= ω + 0.05ω = 1.05ω
=1.05(52.34)=54.96
Centrifugal force at minimum
speed Fc1` = 1m 2r
r1 =r – h1(x/y)
=0.075-(0.03/2)(1)
=0.06
Fc1` = m 2
1
r = 3.56(49.72)2(0.06)
=529.81N
Centrifugal force at maximum
speed Fc2` = 2m 2r
r2 =r + h2(x/y)
=0.075+(0.03/2)(1)
=0.09
Fc2` = m 2
2
r = 3.56(54.76)2(0.09)
=964N
For minimum speed considering friction
S1 + (M.g - F) = 2 Fc1` (x/y)
S1+[(5*9.81)-29.43] =2(529.81)(1)
S1+19.62 =1059.62
S1 =1040 N
For minimum speed considering friction
67
STUCOR
STUCOR APP
S1 + (M.g - F) = 2 Fc1` (x/y)
S1+[(5*9.81)-29.43] =2(529.81)(1)
S1+19.62 =1059.62
S1 =1040 N
For maximum speed considering friction
S2 + (M.g + F) = 2 Fc1` (x/y)
S2+[(5*9.81)+29.43] =2(964)(1)
S2+78.48 =1928
S2 =1849.52 N
Stiffness of the spring (S)
S = (S2- S1)/h
=(1849.52 – 1040)/0.03
=26984 N/m = 26.98KN/m
iii) initial compression of the spring
= S1/S
=1040 / 26.98*103
=0.0385 m
RESULT:
(i) m = 3.56 kg.
(ii) S = 26.98 KN/m
(iii) S1/S=38.5mm
2). A porter governor has all four arms 300mm long. The upper arms are pivoted
on the axis of rotation and the lower arms are attached to the sleeve at a distance
of 35mm from the axis. Each ball has a mass of 7kg and the sleeve mass is 55kg.If
the extreme radii of rotation of the balls are 200mm and 250mm,determine the
range of speed of the governor? [NOV/DEC 2015,May/June 2016]
Given data:
AB=BC=300mm,
CE = 35mm,
m= 7kg,
M = 55kg
r1=200mm,
r2=250mm
Solution:
Minimum speed when r1= 200mm
From the geometry
h1 = AD =
68
STUCOR
STUCOR APP
=
=0.224 m
BF = BD – FD
=200-35
=165 mm
CF =
=
= 0.25m
From Δ le ABD
Tan α1 = =
= 0.893
Tan α1 = =
= 0.66
q = =
= 0.739
The minimum speed is given by
N21 = (895/h1)
= (895/0.224)
= 31292.2
N1 = 176.89 rpm
For Maximum speed

From the geometry
h2 = AD =
69
STUCOR
STUCOR APP
=
=0.166 m
BF = BD – FD
=250-35
=215 mm
CF =
=
= 0.209m
From Δ le ABD
Tan α1 = =
= 1.506
Tan β1 = =
= 1.029
q = =
= 0.683
The maximum speed is given by
N22 = (895/h2)
= (895/0.166)
N2 = 202.59 rpm
Range of
speed = max.speed – min.speed
= 202.58 – 176.89
= 25.69 rpm
70
STUCOR
STUCOR APP
3. A proell governor has equal arms of length 250mm.the upper and lower ends of
the arms are pivoted on the axis of the governor. The extension arms of the
lower links are each 90mm long and parallel to the axis. When the radii of
rotation of the balls are 130mm and 175mm. The mass of each ball is 8.5 kg and
the mass of the central load is 85 kg. Determine the range of speed of the governor
[MAY 2014]
Given data:
AB=BC=250mm,
EB=90mm,
r1=130mm,
r2=175mm,
m=8.5kg,
M=85kg
For minimum speed when r1=130mm
h1 = AD =
=
=0.2135m
BM=DC=AD=0.2135m
α=β so q = 1
N2 1 = (895/h1)
= (895/0.2135)
=32438.2
N1 =180.1 rpm
For maximum speed when r2=175mm
h2 = AD =
STUCOR
STUCOR APP 71
STUCOR
STUCOR APP
=
=0.1785m
BM=DC=AD=0.1785m
EM=EB+BM
=0.09+0.1785
=0.2685m
α=β so q = 1
N2 2 = (895/h2)
= (895/0.1785)
=36666.67
N1 =191.48 rpm
Range of speed = maximum speed – minimum speed
=191.48-180.1
=11.38rpm
4) The turbine rotor of a ship has a 2.4 tonnes and rotates at 1750 rpm when
viewed from the left. The radius of gyration of the rotor is 300mm.Determine
gyroscopic couple and its effect when
(i) The ship turns right at a radius of 250m with a speed of 22kmph.
(ii) The ship pitches with the bow rising at an angular velocity of 0.85
rad/sec.
(iii) The ship rolls at an angular velocity of 0.15rad/sec [NOV/DEC 2013]
Given data:
m = 2.4 t = 2400kg, N=1750rpm , k= 300mm , v= 22kmph = 22*(5/18)=6.11m/s
R = 250m.
Solution:
72
STUCOR
STUCOR APP
Mass moment of inertia I = mk2
= 2400(0.3)2
= 216 kg-m2
Angular velocity(ω)
= 183.26 rad/sec
1. When ship takes right turn
Angular velocity of precession (ωp)
ωp = V / R = 6.11 / 250
= 0.0244 rad /sec
Gyroscopic couple (C)
C = I ω ωp
=216(183.26)(0.0244)
=967.44N-m
The effect is to lower the bow (fore) and raise the stern (aft)when the ship turns right.
2. When ship pitches with bow rising
Angular velocity of precession (ωp)
ωp = 0.85 rad/sec
C = I ω ωp
=216(183.26)(0.85)
=33.64N-m
The effect of the reaction couple when the bow is raising is to turn the ship towards
right
3. When ship rolls
Angular velocity of precession(ωp)
ωp = 0.15 rad/sec
C = I ω ωp
=216(183.26)(0.15)
=5937.6N-m
As the axis of spin is always parallel to the axis of precession for all position, there is no
gyroscopic effect on the ship.
5).The driving axle of a locomotive with two wheels has a moment of inertia of 175
kg/m2.The diameter of the wheel treads is 1.7m and the distance between wheel
centers is 1.5m. When the locomotive is travelling on a level track @ 88km/hr,
defective ballasting causes one wheel to fall 5mm and rise again in a total time of
73
STUCOR
STUCOR APP
0.1 sec, if the displacement of the wheel takes place with simple harmonic motion.
Find
1. Gyroscopic couple setup
2. The reaction between the wheel and rail due to this couple.
[April/May 2015]
Given data:
I = 175kg/m2 ,dw = 1.7m, x=1.5m, v = 88km/hr =88*(5/18) =24.44m/s tp=0.1 sec
fall = 0.005mm
Solution:
1. Gyroscopic couple setup(C)
Angular velocity (ω)
= V / rw
=24.44 / 0.85
=28.75 rad/sec
Since the defective ballasting causes one wheel to fall 5mm and rise again in a
total time of 0.1sec
Therefore amplitude A = ½(fall)= ½(rise)
= ½(0.005)
=0.0025 mm
Maximum velocity while falling
Vmax=(2π/tp)A
=(2π/0.1)0.0025
=0.157 m/s
Gyroscopic couple setup (C)
C = I ω ωp
=175(28.75)(0.105)
=528.28 N-m
2. Reaction between the wheel and rail due to the gyroscopic couple.
P = C/x = 528.18 / 1.5
= 352.2 N
PART C
(1). A spring loaded governor is shown in figure the two balls,each of

mass 6 kg, are connected across by two springs. An auxiliary spring B provides
an additional force at the sleeve through the medium of a lever which pivots
about a fixed centre at its left hand end. In the mean position, the radius of the
governor balls is 120 mm and the speed is 600 r.p.m. the tension in each spring
is then 1 kN. Find the tension in the spring B for this position.
74
STUCOR
STUCOR APP
When the sleeve moves up 15 mm, the speed is to be 630 r.p.m.Find
the necessary stiffness of the spring B, if the stiffness of each spring A is 10
kN/m.Neglect the moment produced by the mass of the balls.
Given Data:
m = 6 kg
r =r1 = 120 mm = 0.12 m
N =N1 = 600 rpm
To Find:
Tension in spring B
Stiffness of the spring B
Solution:
Let consider
SB1 = Spring force
M.g = Total load at the sleeve
We know that centrifugal force at the minimum
speed Fc1 = m (ω1)2 r1 = 6 (62.84)2 0.12 =
2843 N
STUCOR
STUCOR APP 75
STUCOR
STUCOR APP
Since the tension in each spring A is 1 kN and there are two
springs,therefore Total spring force in spring A,
SA1 = 2 x 1 = 2000 N
Taking moments about the pivot P(neglecting the moment produced by the mass
of balls) in order to find the force Mg on the sleeve,in the mean position as
shown in Fig
Now taking moments about point Q,
Stiffness of the spring B
Given : h = 15 mm = 0.015 m; N2 = 630 r.p.m ; SA = 10 kN/m
76
STUCOR
STUCOR APP
First of all, let us find the maximum radius of rotation (r2) when the sleeve moves up
by 0.015 m. we know that
Centrifugal force at the maximum speed,
We know that extension of the spring A,
= 2 ( r2 –r1) x No.of springs
= 2 (0.135-0.12)2 = 0.06 m
Total spring force in spring A,
SA2 = SA1 + Extension of springs x Stiffness of springs
= 2000 + 0.06 x 10x 103 = 2600N
Now taking moments about P, neglecting the obliquity of arms,
Again taking moments about point Q in order to find the spring force SB2 when
sleeve rises as shown in figure in maximum
When the sleeve rises 0.015 m , the extension in spring B
Stiffness of the spring B ,
STUCOR
STUCOR APP
Industrial/ practical connectivity of the subject:
The dynamic analysis of machines begins with a rigid-body model to determine reactions at
the bearings, at which point the elasticity effects are included. The rigid-body dynamics studies
the movement of systems of interconnected bodies under the action of external forces. The
formulation and solution of rigid body dynamics is an important tool in the computer
simulation of mechanical systems.
Dynamic loads and undesired oscillations increase with higher speed of machines. At the
same time, industrial safety standards require better vibration reduction. Typical dynamic
effects, such as the gyroscopic effect, damping and absorption, shocks, resonances of higher
order, nonlinear and self-excited vibrations may be observed in machines like manipulators,
flywheels, gears, mechanisms, motors, rotors, hammers, block foundations, presses, high speed
spindles, cranes, and belts.
78
STUCOR
STUCOR APP
Question Bank
Reg. No
Question paper code: 31568
B.E/ B.Tech. DEGREE EXAMINATION, NOVEMBER / DECEMBER 2013.
FIFTH SEMESTER
MECHANICAL ENGINEERING
ME 2302/ ME 52/ ME 1301 / 10122 ME 503 – DYNAMICS OF MACHINERY
(REGULATION 2008/2010)
( COMMON TO PTME 2302 – DYNAMICS OF MACHINERY FOR B.E. (PART TIME) FOURTH SEMESTER
MECHANICAL ENGINEERING – REGULATION 2009)
TIME ; THREE HOURS MAXIMUM : 100 HOURS
ANSWER ALL QUESTIONS.
PART – A (10×2 = 20 MARKS)
1. Define shaking force. (Page No: 10 Q.No – 8)

2. Write the conditions for any distributed mass have the same dynamical properties.
(Page No: 10 Q.No – 8)
3. Define hammer blow in locomotives. (Page No: 19 Q.No – 8)
4. What are the conditions required for complete balancing of reciprocating parts?
5. Define damping factor and damping coefficient. (Page No: 31 Q.No – 7)
6. What is nodal section in two rotor system?
7. Define step input and harmonic forcing function. (Page No: 42 Q.No – 3)
8. Define transmissibility.
9. Define sensitiveness of a governor. (Page No: 51 Q.No – 1)
10. List some of the terms related to motion of ships using gyroscopic principle.
Part B – (5× 16 = 80 marks)

11. (a) (i) Derive the equation of forces on the reciprocating parts of an engine neglecting the
weight of the connecting rod. (12)
(ii) What is turning moment diagram and draw it ‘s for four stroke IC engine? (4)
Or
(b) A single cylinder, single acting, four stroke gas engine develops 25kw at 320 rpm. The work done by
the gases during the expansion stroke is three times the work done on the gases during the
compression stroke. The works done during the suction and exhaust stroke being negligible. The
fluctuation of speed is not to exceed ±2% of the speed. The turning moment diagram during
compression and expansion is assumed to be triangular in shape. Find the weight of the flywheel if
its radius of gyration is 0.5m (16)
79
STUCOR
STUCOR APP
12.(a) The following data refer to an outside cylinder uncoupled locomotive(Pg No: 21 Q.No – 2)
Mass of rotating parts per cylinder = 350kg

Mass of reciprocating parts per cylinder =
300kg Angle between cranks = 900
Crank radius = 0.3m
Cylinder centers = 1.8m
Radius of balance masses = 0.8m
Wheel centers = 1.5m
If whole of the rotating and 2/3 rd of the reciprocating parts are to be balanced in planes of
the driving wheels, find (i) magnitude and angular positions of balance masses, (ii) speed
in km/hr at which the wheel will lift off the rails when the load on each driving wheels is
30 KN and the diameter of tread driving wheels is 1.8m and (iii) swaying couple at speed
found in plane. (16)
Or
(b) The axes of the three cylinder air compressor are at 1200 to one another and their
connecting rods are coupled to a single crank. The length of each connecting rods is 240
mm and the stroke is 160 mm. the reciprocating parts have a mass of 2.4 kg per cylinder.
Determine the primary and secondary forces if the engine runs at 2000rpm. (16)
13. (a) (i) A machine weighs 18kg and is supported on springs and dashpots. The total stiffness of
the springs is 12 N/mm and damping is 0.2 N/mm/s the system is initially at rest and a
velocity of 120mm/s is imparted to the mass. Determine (i) the displacement and velocity
of mass as a function of time (ii) the displacements and velocity after 0.4s (12)
(ii) Describe the types of vibration with simple sketch. (4)
Or
(b) A torsional system is shown in fig. find the frequencies of trosional vibration and thepositions
of the nodes also find the amplitudes of vibrations G = 84 ×109 N/m2 (16)
Flywheel
Engine C Propeller
A B
45mm 40mm
30 kg.m2 90 50
2. k 4. kg.
0 g 0 m2
m .
m
m
2
STUCOR
STUCOR APP 80
STUCOR
STUCOR APP
14 (a) (i) Derive the relation for the displacement of mass from the equilibrium position of a
damped vibration system with harmonic forcing. (12)
(ii) Define the term vibration isolation. (4)

Or
(b) (i) Discuss the forcing due to support motion. (10)
(ii) What is meant by magnification factor in case of forced vibrations? (6)
15. (a) (i) Explain the function of a proell governor with the help of a neat sketch. Derive the
realationship among the various forces acting on the link. (12)
(ii) What are centrifugal governors ? how do they differ from inertia governors ? (4)
Or
(b) (i) The turbine rotor of a ship has mass of 2.2 tonnes and rotates at 1800 rpm clockwise when
viewed from the aft. The radius of gyration of the rotor is 320 rpm. Determine gyroscopic
couple and its effect when
(1) The ship turns right at a radius of 250 m with a speed of 25 Km/h.
(2) The ship pitches with the bow rising at an angular velocity of 0.8 rad/sec.
(3) The ship rolls at an angular velocity of 0.1 rad/sec. (Page No: 60 Q.No – 4) (12)
(ii) What is the effect of gyroscopic couple on the stability of a two wheel vehicle taking a turn?
(4)(4)
81
STUCOR
STUCOR APP
Reg No:
Question paper code:516410
B.E/ B.Tech DEGREE EXAMINATION, MAY/JUNE 2014.
Fifth Semester
Mechanical Engineering
ME2302/ME52/ME1301/10122 ME503 – DYNAMICS OF MACHINERY
(Regulation 2008/2010)
(Common to PTME2302- Dynamics of machinery for B.E. ( Part –Time)
Fourth semester Mechanical Engineering –Regulation 2009)
Time: Three hours Maximum : 100

Marks
Answer ALL questions
PART – A (10*2=20
MARKS)
1. What are the requirements of an equivalent dynamical system?

2. Define the terms coefficient of fluctuation of speed and coefficient of fluctuation of energy.
3. When is a system said to be completely balanced? (Page No: 18 Q.No – 5)
4. What is tractive force? (Page No: 18 Q.No – 6)
5. Define damping factor or damping ratio. (Page No: 43 Q.No – 9)
6. What is meant by logarithmic decrement?
7. Define magnification factor as applied to forced vibrations.
8. List out the sources of excitation in forced vibration. (Page No: 42 Q.No – 5)
9. Differentiate between isochronous governors and sensitiveness of governors.
10. What is meant by reactive gyroscopic couple? (Page No: 53 Q.No – 6)
PART –B -95*16=80)
11. (a) A horizontal steam engine runni9ng at 120 rpm has a bore of 250 mm and a stroke of 400
mm. the connecting rod is 0.6 m and the mass of the reciprocating parts is 60 kg. when the
crank has turned through an angle of 45 o from the inner dead centre, the steam pressure on
the cover end side is 550 KN/m 2 and that on the crank end side is 70 KN/m 2 considering the
diameter of the piston rod equal to 50 mm, determine:
(i) Turning moment on the crankshaft,
(ii) Thrust on the bearing, and
(iii) Acceleration of the flywheel, if the power of the engine is 20KW, mass of the
flywheel 60Kg and radius of gyration 0.6m. (16)
STUCOR
STUCOR APP 82
STUCOR
STUCOR APP
Or
(b) A shaft fitted with a flywheel rotates at 250 rpm and drives a machine. The torque of the
machine varies in acyclic manner over a period of 3 revolutions. The torque rises from
750Nm to 3000 Nm uniformly during ½ revolutions and remains constant for the following
revolution. It then falls uniformly to 750 Nm during next half revolution and remains
constant for one revolution, the cycle being repeated thereafter. (16)
12. (a) A,B,C and D are four masses carried by a rotating shaft at radii 100,125’200 and 150 mm
respectively. The planes in which the masses revolve are spaced 600 mm apart and the
mass of B,C and D are 10Kg,5Kg AND 4Kg respectively.
Find the required mass A and the relative angular settings of the four masses so that the
shaft shall be in complete balance. (16)
Or
(b) A four crank engine has the two outer cranks set at 120o to each other, and their
reciprocating masses are each 400 Kg. the distance between the planes of rotation of
adjacent cranks are 450 mm, 750 mm and 600 mm. if the engine is to be in complete
primary baklance,find the reciprocating mass and the relative angular position for each of
the inner crank.
If the length of each crank is 300 mm, the length of each connecting rod is 1.2 m and the
speed of rotation is 240 rpm, what is the maximum secondary unbalanced force?
(16)
13. (a) (i) Explain the term whirling speed or critical speed of a shaft. Prove that the whirling
speed for a rotating shaft is the same as the frequency of natural transverse
vibration. (8)
(ii) Derive an expression for the natural frequency of free transverse and longitudinal
vibration by equilibrium method. (8)
Or
(b) A steel shaft ABCD 1.5 m long has flywheel at its ends A and D. the mass of the flywheel A is
600 Kg and has a radius of gyration of 0.6 m. the mass of flywheel D is 800 Kg and has a radius
of gyration of 0.9 m. the connecting shaft has a diameter of 50 mm for the portion AB which is
0.4 m long; and has a diameter of 60 mm for the portion BC which is 0.5 m long; and has a
diameter of d mm for the portion CD which is 0.6 m long. Determine:
(i) The diameter d of the portion CD so that the node of the tensional vibration of the system will
be at the centre of the length BC; and
(ii) The natural frequency of the torsional vibrations.
(iii) The modulus of rigidity for the shaft material is 80 GN/m2. (16)
14.(a) A mass of 10 Kg is suspended from one end of a helical spring, the other end being fixed.
The stiffness of the spring is 10 N/mm the viscous damping causes the amplitude ton decrease
to one tenth of the initial value in four complete oscillations. If a periodic force of 150 Cos 50t
N is applied at the mass in the vertical direction, find the amplitude of the forced vibrations.
What is its value of resonance? (16)
83
STUCOR
STUCOR APP
Or
(b) (i) Establish an expression for the amplitude of forced vibrations. (8)
(ii) What do you understand by vibration isolation and transmissibility? Explain with suitable
examples. (8)
15. (a) The radius of rotations of the balls of a hartnell governor is 80 mm at the minimum speed
of 300 rpm. Neglecting gravity effect , determine the speed after the sleeve has lifted by 60
mm. also determine the initial compression of the spring, the governor effort and the power,
the particular of the governor are given below:
Length of ball arm = 150 mm, length of sleeve arm = 100 mm, mass of each ball = 4Kg, and
stiffness of the spring =m 25 N/mm. (Page No: 54 Q.No – 1)
(16)
Or
(b) The turbine rotor of the ship has a mass of 3500 Kg. it has a radius of gyration of 0.45 m
and a speed of 3000 rpm clockwise when looking from stern. Determine the gyroscopic
couple and its effect upon the ship:
(i) When the ship is steering to the left on a curve of 100 m radius at a speed of 36 Km/h.
(ii) When the ship is pitching in a simple harmonic motion, the bow falling with its maximum
velocity. The period of pitching is 40 seconds and the total angular displacement between
the two extreme positions of pitching is 12 degrees. (16)
84
STUCOR
STUCOR APP
REG.NO
QUESTION PAPER CODE : 91652

B.E/B.Tech DEGREE EXAMINATIONS , NOVEMBER /DECEMBER 2014
Fifth semester
Mechanical
Engineering
ME 2302/ ME 52 – DYNAMICS OF MACHINERY
Time : Three hours Maximum : 100 marks
Answer All Questions
PART -A (10×2=20Marks)
1. What is the purpose of the flywheel used in an engine?

2. Draw the turning moment diagram of a single cylinder double acting steam engine.
3. How the different masses rotating in different planes are balanced?
4. Define Swaying couple. (Page No: 19 Q.No – 7)
5. What are the causes and effects of vibrations?
6. Define the term “dynamic magnifier”.
7. What do you meant by transmissibility?
8. Define the term “logarithmic decrement” as applied to damped vibrations.
9. What are the effects of the gyroscopic couple on a two wheeled vehicle when
taking a turn?
10. Define sensitiveness of governors. (Page No: 51 Q.No – 1)
85
STUCOR
STUCOR APP
PART -B (5×16 = 80Marks)
11. (a) The equation of the turning moment curve of a three crank engine is (5000 +
1500 sin 3θ) N-m where θ is the crank and in radians. The moment of inertia of the
flywheel is 1000 kg – m2 and the mean speed is 300 rpm. Calculate:
(i) Power of the engine, and (8)
(ii) The maximum fluctuation of the speed of the flywheel in percentage
When
(1) The resisting torque is constant, and (4)
(2) The resisting torque is (5000 + 600 sin θ) N-m (4)
Or
(b)A certain machine requires a torque of (5000 + 500 sin θ) N-m to drive it, where
θ is the angle of rotation of shaft measured from certain datum. The machine is
directly coupled to an engine which produces a torque of (5000 + 600 sin 2θ)N-
m. The flywheel and the other rotating parts attached to the engine have a mass
of 500 kg at a radius of gyration of 0.4 m. If the mean speed is 150 r.p.m., find:
(i) The fluctuation energy, (6)
(ii) The total percentage fluctuation of speed, and (5)
(iii) The maximum and minimum angular acceleration of the flywheel and the
corresponding shaft position. (5)
12.(a) A Shaft carries four masses in parallel planes A, B, C and D in this order along its
length. The masses at B and C are 18 kg and 12.5 kg respectively. And each has
an eccentricity of 80 mm. The angle between the masses at B and A is190 0,both
being measured in the same direction. The axial distance between the planes A
and B is 100 mm and that between B and C is 200 mm. If the shaft is in complete
dynamic balance, Determine : (i) the magnitude of the masses at A and D; (ii) The
distance between the planes A and D; and (iii) The angular position of the mass at
D. (16)
Or
(b) A five cylinder in-line engine running at 750 r.p.m has successive cranks
1440apart, the distance between the cylinder centre lines being 375 mm. the
piton stroke is 225 mm and the ratio of the connecting rod to the crank is 4.
Examine the engine for balance of primary and secondary forces and couples.
Find the maximum values of these and the position of the central crank at which
these maximum values occur. The reciprocating mass for each cylinder is 15 kg.
(16)
13.(a) A vertical steel shaft 15 mm diameter is held in along bearings 1 m apart and
carries at its middle a disc of mass 15 kg. The eccentricity of the centre of
gravity of the disc from the centre of the rotor is 0.30 mm. the modulus of
elasticity for the shaft material is 200 GN/m 2 and the permissible stress is 70
MN/m2.Determine
86
STUCOR
STUCOR APP
(i) The critical speed of the shaft and (ii) The range of speed over which it is
unsafe to run the shaft. Neglect the mass of the shaft. (16)
Or
(b) The vertical shaft of 5 mm diameter is 200 mm long and is supported in long
bearings at its ends. The disc of mass 50 kg is attached to the centre of the shaft.
Neglecting any increase in stiffness due to the attachment of the disc to the shaft.
Find the critical speed of rotation and the maximum bending stress when the
shaft is rotating at 75 % of the critical speed. The centre of the disc is 0.25 mm
from the geometric axis of the shaft. E = 200 GN/m2. (16)
14.(a) A mass of 10 kg is suspended from one end of a helical spring, the other end
being fixed, the stiffness of a spring is 10 N/mm. the viscous damping causes the
amplitude to decrease to one-tenth of the initial value in four complete
oscillations. If a periodic force of a 150 cos50 N is applied at the mass in the
vertical direction, and find the amplitude of the forced vibrations. What is its
value of resonance? (Page No: 45 Q.No – 2) (16)
Or
(b) A machine part of mass 2 kg vibrates in a viscous medium. Determine the
damping coefficient when a harmonic exciting force of 35 N results in resonant
amplitude of 12.5 mm with aperiod of 0.2 sec. if the system is excited by a
harmonic force of frequency 4 Hz, what will be the percentage increase in the
amplitude of vibration when damper is removed as compared with that damping.
(Page No: 47 Q.No – 3) (16)
15.(a) Explain the effect of the gyroscopic couple on the reaction of the four wheels
of a vehicle negotiating a curve. (16)
Or
(b) In an engine governor of the porter type, the upper and lower arms are 200 mm
and 250 mm respectively and pivoted on the axis of rotation. The mass of the
central load is 15 kg, the mass of each ball is 2 kg and friction of the sleeve
together with the resistance of the operating gear is equal to a load of 24 N at the
sleeve. If the limiting inclinations of the upper arms to the vertical are 300 and
0
40 . Find ; taking friction into account, range of speed of the governor.(16)
87
STUCOR
STUCOR APP
Reg No :
B.E/B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2015

Question Paper Code : 27378
Fourth/Fifth Semester
ME6505 – DYNAMIICS OF MACHINES
(Common to Mechanical Engineering(Sandwich)/B.E Mechatronics Engineering)
(Regulations 2013)
Time: Three Hours Maximum : 100 Marks
Answer ALL questions.

PART – A (10 X 2 = 20 Marks)
1. Define D‟Alembert‟s principle for translation and hence define inertia force. (Page No:
9 Q.No – 4&5)
2. Define coefficient of fluctuation of energy of a flywheel. (Page No: 9 Q.No – 2)
3. Define Static balancing of shaft.

4. State the reason for choosing multi cylinder engine in comparison with that of
the single cylinder engine. (Page No: 18 Q.No – 3)
5. Write the mathematical expression for a free vibration system with viscous damping.
6. Write the expression for estimation of the natural frequency of free torsional
vibration of a shaft.
7. What is the phase difference between the transmitted force and the disturbing
force system if ω/ωn > 1.
8. Write the equation of motion for the forced damped vibration.
9. What is meant by hunting in a governors. (Page No: 52 Q.No – 3)
10. What is the angular speed of precession of the shaft(whose mass moment of inertia is
20 kg-m2) if it spins about its axis and torque of 100N-m applied about an axis normal
to it.
27378
88
STUCOR
STUCOR APP
PART – B (5 X 16 = 80 Marks)
11. (a) During a trail on steam engine, it is found that the acceleration of the piston is
36m/s2 when the crank has moved 30o from the inner dead centre position. The
net effective steam pressure on the piston is 0.5 M Pa and the frictional
resistance is equivalent to a force of 600 N. The diameter of the piston is
300mm and the mass of the reciprocating parts is 180kg. If the length of the
crank is 300mm and the ratio of the connecting rod length to the crank length is
4.5.Find (i)reaction on the guide bars (ii) thrust on the crank shaft bearings and
(iii) Turning moment on the crank shaft. (Page No: 11 Q.No – 1) (16)
OR
(b) A single cylinder double acting engine develops 150 KW at a mean speed of 80
rpm. The coefficient of fluctuation of energy is 0.1 and the fluctuation of speed
is ±2% of mean speed. If the mean diameter of the flywheel rim is 2m and the
hub and spokes provide 5% of the rotational inertia of the flywheel, find the
mass and cross -sectional area of the flywheel rim. Assume the density of the
flywheel material(which is cast iron )as 7200 kg/m3. (16)
12. (a) A,B,C and D are four masses carried by a rotating shaft at radii 100,125,200
and 150mm respectively. The planes in which the masses revolve are spaced
600mm apart and the mass of B,C and D are 10 kg, 5kg and 4 kg respectively.
Find the required mass A and the relative angular setting of the four masses so
that the shaft shall be in complete balance. (Page No: 19 Q.No – 1) (16)
OR
(b) A 90o V engine has two cylinders which are placed symmetrically. The two
connecting rods operate a common crank. The length of connecting rod are
320mm each and crank radius is 80mm.The reciprocating mass per cylinder
is 12kg. If the engine speed is 600rpm,then find the resultant primary and
secondary forces. Also find the maximum resultant secondary forces. (16)
13. (a) Determine (i) the critical damping coefficient, (ii) the damping factor, (iii) the
natural frequency of damped vibrations, (iv) the logarithmic decrement and (v) the
ratio of two consecutive amplitudes of a vibrating systems which consists of mass
of 25kg, a spring of stiffness 15KN/m and a damper. The damping provided is only
15% of the critical value. (16)
Or
(b) A shaft of length 1.25m is 75mm in diameter for the first 275mm of its length,
125mm in diameter for the next 500mm length, 87.5 mm in diameter for the
89
STUCOR
STUCOR APP
next 375 mm length and 175mm in diameter for the remaining 100mm of its
length. The shaft carries two rotors at two ends. The mass moment of inertia of
the first rotor is 75 kg/m2 where as of the second rotor is 50 kg/m 2. Find the
frequency of natural torsional vibrations of the system. The modulus of rigidity
of the shaft material may be taken as 80GPa. (Page No: 39 Q.No – 5) (16)
14. (a) A single cylinder vertical petrol engine has a mass of 200kg and is mounted
upon a steel chassis frame. The vertical static deflection of the frame is 2.4mm due
to the weight of the engine. The reciprocating parts of the engine has a mass of 9kg
and move through avertical stroke of 160mm with simple harmonic motion. A
dshpot with a damping coefficient of 1N/mm/s is also used to dampen the
vibrations, considering that the steady state of vibration is reached, Determine:
(i) Amplitude of the forced vibration if the driving shaft rotates at 500rpm and
(ii) The speed of the driving shaft at which resonance will occur. (16)
OR
(b) A machine has a total mass of 90kg and unbalanced reciprocating parts of mass
2kg which moves through a vertical stroke of 100mm with simple harmonic
motion. The machine is mounted on four springs. The machine is having only
one degree of freedom and can undergo vertical displacement only.
Calculate(i) the combined stiffness of the springs if the force transmitted to the
foundation is one thirteenth of the applied force. Neglect damping and take the
speed of rotation of the machine crank shaft as 1000rpm.
When the machine is actually supported on the springs, it is found that the
damping reduces the amplitude of the successive free vibrations by 30%. Find
(ii) the force transmitted to the foundation at 900 rpm. (16)
15. (a)Calculate the minimum speed,maximum speed and range of the speed of a
porter governor, Which has equal arms 200mm long and pivoted on the axis of
rotation. The mass of each ball is 4kg and the central mass on the sleeve is 20 kg.
The radius of rotation of the ball is 100mm when the governor begins to lift and
130mm when the governor is at maximum speed. (16)
90
STUCOR
STUCOR APP
OR
(b) The turbine rotor of a ship has a 3500 kg and rotates at 3000 rpm when viewed
from stern. The radius of gyration of the rotor is 450mm.Determine
(i) The ship turns left at a radius of 100m with a speed of 36kmph.
(ii) When the ship is pitching in a simple harmonic motion the bow falling with
its maximum velocity. The speed of pitching is 40 seconds and the total
angular displacement between the two extreme positions of pitching is 12o.
(Page No: 60 Q.No – 4) (16)
91
STUCOR
STUCOR APP
Reg.No.
B.E/B.Tech. Question Paper Code : 51640

DEGREE EXAMINATION, MAY/JUNE 2014
Fourth Semester
ME2302/ME 52 – DYNAMIICS OF MACHINERY
(Common to PTME 2302 – Dynamics of machinery for B.E (Part time) Fourth
Semester Mechanical Engineering - Regulation 2009)
Time : Three Hours Maximum : 100 Marks

PART – A (10 X 2 = 20 Marks)
1. What are the requirements of an equivalent dynamical system?
2. Define the terms `coefficient of fluctuation of speed` and coefficient of fluctuation
of energy.
3. When is a system said to be a completely balanced? (Page No: 18 Q.No – 5)
4. What is tractive force? (Page No: 18 Q.No – 6)
5. Define damping factor or damping ratio. (Page No: 43 Q.No – 9)
6. What is meant by logarithmic decrement?
7. Define magnification factor as applied to forced vibrations.
8. List out the sources of excitation in forced vibration. (Page No: 42 Q.No – 5)
9. Differentiate between isochronous governors and sensitiveness of governors.
10. What is meant by reactive gyroscopic couple? (Page No: 53 Q.No – 6)
51640
92
STUCOR
STUCOR APP
PART – B (5 X 16 = 80 Marks)
11. (a)A horizontal steam engine running at 120 rpm has a bore of 250mm and a
stroke of 400 mm. The connecting rod is 0.6m and mass of the reciprocating parts is
60kg. When the crank has turned through an angle of 45o from the inner dead centre,
the steam pressure on the cover end side is 550KN/m2 and that on the crank side is
70KN/m2 considering the diameter of the piston rod equal to 50mm. Determine:
(i) Turning moment on the crank shaft
(ii) Thrust on the bearing
(iii) Acceleration of the flywheel, if the power of the engine is 20 KW.
Mass of the flywheel; 60 kg and radius of gyration 0.6m (16)
OR
(b) A shaft fitted with a flywheel rotates at 250 rpm and drives a machine. The
torque of machine varies in a cyclic manner over a period of 3 revolutions. The Torque
rises from 750 Nm to 3000 Nm uniformly during ½ revolution and remain constant for
the following revolution. It then falls uniformly to 750 Nm during next ½ revolution
and remain constant for one revolution, the cycle being repeated thereafter.
Determine the power required to drive the machine and percentage fluctuation in
speed,if the driving torque applied to the shaft is constant and the mass of the flywheel
is 500kg with radius of gyration of 600mm. (16)
12. (a) A, B, C and D are four masses are carried by a rotating shaft at radii
100,125,200and 150 mm respectively. The planes in which the masses revolve are
spaced 600mm apart and the mass of B, C and D are 10kg, 5kg and 4 kg
respectively
Find the required mass A and the relative angular settings of the four masses so
that the shaft shall be in complete balance. (16)
Or
(b) A four crank engine has the two outer cranks set at 120oto each other, and their
reciprocating masses are each 400kg. The distance between the planes of rotation of
adjacent cranks are 450 mm, 750 mm and 600 mm. If the engine is to be in complete
primary balance, find the reciprocating mass and the relative angular position for each
of the inner crank.
93
STUCOR
STUCOR APP
If the length of each crank is 300 mm, the length of each connecting rod is 1.2 m and the
speed of rotation is 240 rpm, What is the maximum secondary unbalanced force? (16)
13. (a) (i) Explain the term `whirling speed` or `critical speed` of a shaft. Prove that the
Whirling speed for a rotating shaft is the same as the frequency of natural
transverse vibrations.
(ii) Derive an expression for the natural frequency of free transverse and
longitudinal vibration by equilibrium method. (16)
OR
(b) A steel shaft ABCD 1.5m long has flywheel at its end A and D. The mass of
The flywheel A is 600 kg and has a radius of gyration of 0.6 m. The mass of the
flywheel D is 800 kg and has a radius of gyration of 0.9m. the connecting shaft has a
diameter of 50mm for the portion AB which is 0.4m long and has a diameter of 60 mm
for the portion BC which is 0.5 m long and has a diameter of d mm for the portion CD
which is 0.6 m long. Determine:
(i) The diameter d of the portion CD so that the node of the torsional vibration
of the system will be at the centre of the length BC; and
(ii) The natural frequency of the torsional vibrations.
(iii) The modulus of rigidity for the shaft material is 80GN/m2. (16)
14. (a) A mass of 10 kg is suspended from one end of a helical spring, the other end
being fixed. The stiffness of the spring is 10 N/mm the viscous damping causes the
amplitude to decrease to one tenth of the initial value in four complete oscillations.
If a periodic force of 1150 Cos 50t N is applied at the mass in the vertical direction,
find the amplitude of the forced vibrations. What is its value of resonance?
(16)
OR
(b) (i) Establish an expression for the amplitude of forced vibrations. (8)
(ii)What do you understand by vibration isolation and transmissibility? Explain
with suitable examples. (8)
94
STUCOR
STUCOR APP
15. (a)The radius of rotation of the balls of a Hartnell governor is 80 mm at the
minimum speed of 300 rpm. Neglecting gravity effect, determine the speed
after the sleeve has lifted by 60 mm. Also determine the initial compression of the
spring, the governor effort and the power. The particular of the governor are given
below:
Length of the ball arm = 150mm, Length of sleeve arm = 100mm, mass of each ball
= 4 kg, and stiffness of the spring = 25 N/mm. (Page No: 54 Q.No – 1) (16)
OR
(b) The turbine rotor of a ship has a 3500 kg and rotates at 3000 rpm when viewed
from stern. The radius of gyration of the rotor is 450mm.Determine
(i) The ship turns left at a radius of 100m with a speed of 36kmph.
(ii) When the ship is pitching in a simple harmonic motion the bow falling
with its maximum velocity. The speed of pitching is 40 seconds and the
total angular displacement between the two extreme positions of
pitching is 12o (16)
51640
95
STUCOR
STUCOR APP
Reg.No.
B.E/B.Tech. Question Paper Code : 57572

DEGREE EXAMINATION, MAY/JUNE 2016
Fourth Semester
Mechatronics Engineering
ME6505 – DYNAMIICS OF MACHINES
(Common to Fourth Semester Mechanical Engineering)
(Regulations 2013)

PART – A (10 X 2 = 20 Marks)
1. Distinguish between crank effort and piston effort.
2. Define D‟Alembert‟s principle. (Page No: 09 Q.No – 5)
3. Differentiate: Static and Dynamic balancing. (Page No: 18 Q.No – 1)
4. What is meant by balancing of rotating masses? (Page No: 18 Q.No – 2)
5. Define the term logarithmic decrement. (Page No: 31 Q.No – 8)
6. What are the different types of vibratory motions? (Page No: 30 Q.No – 1)
7. Define magnification factor. (Page No: 42 Q.No – 4)
8. What is the effect of inertia on the shaft in longitudinal and transverse vibrations?
9. Write short note on “hunting of governors”.
10. The engine of an aeroplane rotates in clockwise direction when seen from the tail end
and the aeroplane takes a turn to the left. What will be the effect of gyroscopic
couple on the aeroplane? (Page No: 53 Q.No – 9)
52572
96
STUCOR
STUCOR APP
PART – B (5 X 16 = 80 Marks)
11. (a) The ratio of the connecting rod length to crank for a vertical petrol engine is 4 : 1.
The bore/stroke is 80/100 mm and mass of the reciprocating part is 1kg. The gas
pressure on the piston is 0.5 N/mm 2 when it has moved 10 mm from the TDC on its
power stroke. Determine the net head on the gudgeon pin. The engine runs at 1800 rpm.
What engine speed will this load be zero? (Page No: 12 Q.No – 2) (16)
OR
(b) (i) Derive the equation of forces on the reciprocating parts of an engine, neglecting
the weight of the connecting rod. (10)
(ii) What is turning moment diagram and draw it for 4 stroke IC engine. (6)
12. (a) Three masses are attached to a shaft as follows: 10 kg at 90 mm radius; 15 kg at 120
mm radius and 9 kg at 150 mm radius. The masses are to be arranged so that shaft is in
static balance. Determine the angular position of masses relative to 10 kg mass. All the
masses are in the same plane. (16)
OR
(b) (i) What is meant by swaying couple? Deduce the expression for its magnitude
and explain its influence. (10)
(ii) State the methods of force balancing of linkages by Lowen and Berk of
method. (6)
13. (a)Derive the expression for the natural frequency of free transverse or
longitudinal vibrations by (i) Equilibrium method, (ii) Energy method. (Page No: 33 Q.No –
2) (16)
OR
52572
(b) Find the equation of motion for the spring-mass-dashpot system shown in fig. For cases,
when (i) ξ = 2. (ii) ξ = 1, and (iii) ξ =0.3. The mass „m‟ is displaced by a distance of 30 mm
and released. (16)
97
STUCOR
STUCOR APP
14. (a) A single vertical petrol engine of total mass of 200 kg is mounted upon a steel
chassis frame. The vertical static deflection of the frame is 2.4 mm due to the weight of
the engine. The mass of the reciprocating parts is 9kg and the stroke of the piston is 160
mm with S.H.M. If dashpot of damping coefficient of 1N/mm/s is used to dampen the
vibrations, calculate at steady state: (16)
(i) The amplitude of forced vibrations at 500 rpm engine speed and
(ii) The speed of the driving shaft at which resonance will occur.
OR
(b) (i) Derive the equation of vibration isolation factor or transmissibility ratio. (Page No: 50
Q.No – 5) (10)
(ii) Write short notes on (1) frequency response curve and (2) phase frequency
response curve. (6)
15. (a) (i) Discuss the effect of the gyroscopic couple on a two wheeled vehicle while
taking a turn. (6)
(ii) A turbine of a ship has a mass of 20 tonnes and a radius of gyration of 0.75m. Its speed
is 2000 rpm. The ship pitches 6 ° above and below the horizontal position. One complete
oscillation takes 20 seconds and the motion is simple harmonic. Calculate the maximum
couple tending to shear the holding down bolts of the turbine and the maximum angular
acceleration of the ship during pitching. (10)
98
STUCOR
STUCOR APP
OR
(b) A porter governor has all four arms 300 mm long. The upper arms are pivoted on the
axis of rotation and lower arms are attached to the sleeve at distance of 3.5 mm from
the axis. The mass of each ball is 7 kg and mass on the sleeve is 54kg. If extreme
radii of rotation of the balls are 200 mm and 250 mm. Determine the range of speed
of governor. (Page No: 56 Q.No – 2) (16)
57572
99
STUCOR
STUCOR APP
Reg. No.
B.E./B.Tech. DEGREEQuestion Paper Code: APRIL/MAY

EXAMINATION, 71855 2015
Fifth Semester
Mechanical
Engineering
ME 2302/ME52/ME1301/10122 ME 503 – DYNAMICS OF MACHINERY
(Regulations 2008/2010)
(Common to PTME 2302/10122 ME 503- Dynamics of Machinery for B.E. (Part-Time)

Fourth semester Mechanical Engineering- Regulations 2009/2010)
Time – Three hours Maximum:

100 Marks
Answer all questions
Part – A (10 X 2 = 20
marks)
1. State the principle of virtual work.
2. Define inertia and inertia force.
3. List out two conditions required for complete external balancing of a rotating system.
4. What is known as hammer blow in reciprocating engines? (Page No: 19 Q.No – 8)
5. Write the vibration characteristics.
6. Differentiate coulomb damping and viscous damping.
7. Define vibration isolation.
8. What is fundamental frequency?
9. Enlist the difference between a governor and a flywheel. (Page No: 52 Q.No – 4)
10. Depict the effect of gyroscopic couple in ships during pitching. (Page No: 53 Q.No – 8)
STUCOR
STUCOR APP 100
STUCOR
STUCOR APP
PART – B (5 X 16 = 80 marks)
11. a) Refer Fig.11 (a). Determine the couple on a crank 2 to be applied for equilibrium of
the system, when a force of 500 N acts on the connecting rod at point C as shown. Also
determine the resultant of forces exerted on the frame of the engine. (16)
Fig.11(a)
Or
b) The lengths of crank and connecting rod of a horizontal reciprocating engine are 100 mm
and 500 mm respectively. The crank is rotating at 400 rpm. When the crank has turned
30˚ from the inner dead centre, find analytically i) acceleration of the piston, ii) velocity
of the piston, iii) angular velocity of the connecting rod and iv) angular acceleration of
the connecting rod.
12. a) The following data are related to a two cylinder locomotive with cranks at 90˚:
i) Mass of the reciprocating parts/cylinder = 300 kg,
ii) Crank radius = 300 mm,
iii) Diameter of driving wheel = 1800 mm,
iv) Distance between cylinder axis = 600 mm
v) Distance between the driving wheel = 1600
mm Determine:
1) The fraction of the reciprocating masses to be balanced if the hammer

blow is not to exceed 45 kN at 95 kmph,
2) The variation in tractive effort.
3) The maximum swaying couple.
Or
b) A shaft carries four masses A,B,C and D of magnitude 200 kg, 300 kg, 400 kg and 200
kg respectively and revolving at radii 80 mm, 70 mm, 60 mm and 80 mm in planes
101
STUCOR
STUCOR APP
measured from A at 300 mm, 400 mm and 700 mm. The angles between the cranks
measured anticlockwise are A to B 45˚, B to C 70˚ and C to D 120˚. The balancing
masses are to be placed in planes X and Y. the distance between the planes A and X is
100 mm between X and Y is 400 mm between Y and D is 200 mm. if the balancing
masses revolve at a radius of 100 mm. find their magnitudes and angular positions.
13. a) A spring loaded governor of the Hartnell type has equal arms. The balls rotate in a
circle of 15 cm dia when the sleeve is in the mid position and the ball arms are vertical.
The equilibrium speed for this position is 500 rpm. The maximum sleeve movement is
to be 3 cm and the maximum variation of speed taking in account the friction to be ±5%
of the mid position speed. The mass of the sleeve is 5 kg and frictio force may be
consideration to arise out of an equivalent 3 kg mass at the sleeve. The power of the
governor must be sufficient to overcome the friction by 1% change of speed either way
from mid position.
Determine :
i) The rotating mass,
ii) The spring stiffness,
iii) The initial compression of
spring. Neglect the obliquity effect of arms.
Or
b) The driving axle of a locomotive with two wheels has a mass moment of inertia of 350
kg m2. The wheels are 1.8 mm diameter. The distance between the planes of the wheels
is 1.5 m. when travelling at 100 km/hr the locomotive passes over a defective rail which
causes the right hand wheel to fall 10 mm and rise again in a total time of 0.1 sec, the
vertical movement of the wheel being with SHM. Find the maximum gyroscopic torque
caused. Determine the direction in which it acts when the wheel is failing. Let the linear
motion of the right hand wheel is α cos qt, where α = 0.005m and q = (2π/0.1) rad/sec
14. a) A flywheel having a mass of 35 kg was allowed to swing as pendulum about a knife-
edge at the inner side of the rim, as shown in Fig.14(a). If the measured time period of
oscillation was 1.25 second, determine the moment of inertia of the flywheel about its
geometric axis.
102
STUCOR
STUCOR APP
Fig.14(a). Flywheel as Pendullum

Or
b) The disc of a torsional pendulum has a moment of inertia of 0.068kg-m2 and it immersed
in a viscous fluid. The brass shaft (G = 40 GN/m2) attached to it is of 10 mm diameter
and 380 mm length, when the pendulum is vibrating the amplitudes on the same side of
the rest position for successive cycles are 5˚,3˚ and 1.8˚. determine i) the logarithmic
decrement, ii) the damping torque at unit velocity, iii) the periodic time of vibration.
What would be the frequency of vibrations if the disc were removed from the viscous
fluid?
15. a) The diagram shows a mass-spring-dashpot system. The support is moved with a motion
of y = 6 sin (40 t) mm. determine the amplitude of the mass and the phase angle.
Or
b) The time of free vibration of a mass hung from the end of a helical spring is 0.8s. when
the mass is stationary, the upper end is made to move upwards with displacement Y
mm given by Y = 16 sin 2πt, where t is time in seconds measured from the beginning
of the motion. Neglecting the mass of spring and damping effect, determine the vertical
distance through which the mass is moved in the first 0.3seconds.
103
STUCOR
STUCOR APP
. Reg. No
Question PaperNOVEMBER/DECEMBER
B.E./B.Tech. DEGREE EXAMINATION, Code: 21855 2015
Fifth Semester
Mechanical
Engineering
ME 2302/ME52/ME1301/10122 ME 503 – DYNAMICS OF MACHINERY
(Regulations 2008/2010)
(Common to PTME 2302/10122 ME 503- Dynamics of Machinery for B.E. (Part-Time)

Fourth semester Mechanical Engineering- Regulations 2009/2010)
Time – Three hours Maximum:

100 Marks
Answer all questions
Part – A (10 X 2 = 20
marks)
1. The length of crank and connecting rod of vertical reciprocating engine are 200 mm and
1.5 m respectively. If the crank rotates at 200 rpm. Find the velocity of piston at θ =
40˚. (Page No: 10 Q.No – 10)
2. Why the weight of flywheel for single cylinder engine is heavier than that of
some powered multi cylinder engine?
3. What do you mean by partial balancing of single cylinder engine? (Page No: 18 Q.No – 4)
4. In case of balancing of rotary masses in different planes, how many planes in

which balance masses will be kept?
5. Why transient sloution is not conisered in the response of forced damped

vibrating system?
6. If a damper exerts a force of 30 kN at a speed of 2m/s movement, determine

the damping coefficient.
7. Define transmissibility.
8. Classify vibration. (Page No: 43 Q.No – 7)
9. Why too sensitivity governors are not useful?
10. What is the function of active gyrocouple?
104
STUCOR
STUCOR APP
PART – B (5 X 16 = 80 marks)
11. a) A vertical petrol engine 150 mm diameter and 200 mm stroke has a connecting rod
350 mm long. The mass of the piston is 1.6 kg and engine speed is 1800 rpm. On the
expansion stroke with crank angle 30˚ from top dead centre, the gas pressure is 750
kN/m2. Determine the net thrust on the piston.
Or
b) The turning moment diagram for multi cylinder engine has been drawn to a vertical scale
of 1 mm = 650 Nm and a horizontal scale of 1 mm = 4.5˚. the area above and below the
mean torque line are -28, +380, -260, +310, - 300, + 242, -380, +265 and -229 mm 2, the
fluctation of speed is limited to ± 1.8% of the mean speed which is 400 rpm. Density of
rim material is 700 kg/m3 and width of the rim is 4.5 times its thickness. The hoop
stress in the rim material is limited to 6 N/mm2. Neglecting the effect of the boss and
arms, determine diameter and cross section of flywheel rim. (Page No: 13 Q.No – 3)
12. a) Data of three unbalance masses A,B and C are given below Ma = 4 kg, Mb = 3 kg Mc
= 2.5 kg, Ra = 75 mm, Rb = 85 mm, Rc = 50 mm, θa = 45˚, θb = 135˚, θc = 240˚( θ
measured from right horizontal axis at the origin) the shaft length is 800 mm between
bearings. These three masses are completely balanced by two counter masses located 75
mm from each bearings. The axial distances of the threee unbalanced masses are L a =
150 mm, Lb = 350 mm, Lc = 525 mm from the right hand side of the contour mass
plane. Determine the masses and angular position s of the countour masses, if the radial
location of the contour masses are Rb1 = 75 mm and Rb2 = 40 mm.
Or
b) The following data are related to a single cylinder reciprocating engine:
Mass of the reciprocating parts = 40 kg,
Mass of revolving parts = 30 kg at 180 mm
radius, Speed = 150 rpm, stroke = 350 mm.
If 60% of the reciprocating parts and all the revolving parts are to be balanced.
Determine:
i) The balance mass required at radius of 320 mm,
ii) The unbalanced force when the crank has turned 45˚ from the top dead centre.
13. a) A rotor has mass of 12 kg and is mounted midway on a 24 mm diameter horizontal

shaft supported at the ends by two bearings. The bearings are 1 m apart. The shft rotates
at 2400 rom. If the centre of mass of the rotor is 0.11 mm above from the geometric
centre of the rotor due to a certain manufacturing defects, find the amplitude of the
study state vibration and the dynamic force transmitted to the bearing. Take E = 200
GN/m2.
Or
105
STUCOR
STUCOR APP
b) The shaft carries two masses. The mass A is 300 kg with radius of gyration of 0.75 m
and the mass B is 500 kg with radius of gyration of 0.9 m the shaft is a stepped shaft
having 100 mm diameter for 300 mm length, 150 mm diameter for 160 mm length, 120
mm diameter for 125 mm length and 90 mm diameter for 400 mm length. Determine
the frequency of the natural torsional vibration. It is desired to have node at the mid
section of shaft of 120 mm diameter by changing the diameter of the section having 90
mm diameter, what will be the new diameter. Take C = 84 GN/m2.
14. a) A machine with a mass of 500 kg has an amplitude of vibration 0.01m when operating
at a speed of 49 Hz. If the machine is critically damped and spring stiffness
coefficient is 10 x 103 N/m. Find the amount of unbalance.
Or
b) The static deflection of an electric motor of mass 400 kg supported by a system of four
parallel springs and the static deflection is found to be 50 mm. if the electric motor has rotating
unbalance of 20 kgm. Determine
i) The amplitude of vibration at 2000 rpm
ii) The force transmitted to the ground.
15. a) In a spring loaded governor, the controlling force curve is a straight line. The balls are
400 mm apart, when the controlling force is 1500 N and 240 mm when it is 800 N. the
mass of each ball is 10 kg. Determine the speed at which the governor runs, when the
balls are 300 mm apart. By how much should the initial tension be increased to make
the governor isochronous? Also find the isochronous speed.
Or
b) The turbine rotor of a ship has mass of 2.2 tones and rotates at 1800 rom clockwise
when viewed from the aft. The radius of gyration of rotor is 320 mm. determine
the gyroscopic couple and its effect when
i) The ship turns right at a radius of 250 m with a speed of 25 km/hr,
ii) The ship pitches with the bow rising at an angular velocity of 0.8 rad/s,
iii) The ship rolls at an angular velocity of 0.1 rad/sec.
106
STUCOR
STUCOR APP
Reg.No.
B.E/B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2012

Question Paper Code : 11528
Fifth Semester
Mechatronics Engineering
ME 2302/ME 52/ME 1301 – DYNAMIICS OF MACHINERY
(Common to PTME 230 – Dynamics of Machinery for B.E (Part-Time)Fourth Semester
Mechanical Engineering)
(Regulations 2008)

PART – A (10 X 2 = 20 Marks)
1. Distinguish “piston effort” and “crank effort”. (Page No: 09 Q.No – 1)
2. What is the function of a flywheel? How does it differ from that of a governor? (Page
No: 10 Q.No – 6)
3. Differentiate: Static and Dynamic balancing. (Page No: 18 Q.No – 9)
4. Define hammer blow.
5. What is difference between damping and viscous damping? (Page No: 30 Q.No – 4)
6. What is meant by whirling speed of the shaft? (Page No: 30,43 Q.No – 5,8)
7. Define isolation factor. (Page No: 42 Q.No – 2)
8. Write down the expression for amplitude of forced vibration.
9. Define “hunting of a governors”. (Page No: 52 Q.No – 3)
10. What is the effect of gyroscopic on an automobile taking a turn? (Page No: 53 Q.No – 8)
107
STUCOR
STUCOR APP
11528
PART – B (5 X 16 = 80 Marks)
11. (a) Deduce an expression for the inertia force in the reciprocating parts, neglecting the
weight of the connecting rod. (16)
OR
(b) (i) The turning moment curve for an engine is representd by the equation,
T=(20,000 + 9500 sin 2θ – 5700 cos 2θ ) N-m, where θ is the angle moved by the crank
from inner dead centre. If the resisting torque is constant, find
(i) power developed by the engine,
(ii) Moment of inertia of flywheel in kg-m2,if the total fluctuation of speed is not the
exceed 1% of mean speed which is 180 rpm,and
(iii) Angular acceleration of the flywheel when the crank has turned through 450 from
inner dead centre. (Page No: 16 Q.No – 5) (16)
12. (a) A,B,C and D are four masses carried by a rotating shaft at radii 100, 125, 200 and
150 mm respectively. The planes in which the masses revolve are spaced 600 mm apart
and the mass B,C and D are 10 kg, 5 kg and 4kg respectively.
Find the required mass A and the relative angular setting of the four masses so that the
shaft shall be in complete balance. (16)
OR
(b) A four crank engine has the two outer cranks set at 120 0 to each other, and their
reciprocating masses are each 400 kg. The distance between the planes of rotation of
adjacent cranks are 450 mm, 750 mm and 600 mm. If the engine is to be in complete
primary balance, find the reciprocating mass and relative angular position for each of
the inner cranks. If the length of each crank is 300 mm, the length of each connecting
rod is 1.2 m and the speed of rotation is 240 rpm. What is the maximum secondary
unbalanced force? (Page No: 23 Q.No – 3) (16)
13. (a) The mass of a single degree damped vibrating system is 7.5 kg and makes 24 free
oscillations in 14 seconds when disturbed from its equilibrium position. The amplitude
of vibration reduces to 0.25 of its initial value after five oscillations. Determine (i)
Stiffness of the spring,
(ii) Logarithmic decrement and
(iii) Damping factor. (Page No: 38 Q.No – 4) (16)
108
STUCOR
STUCOR APP
OR
(b) (i) Derive an expression for the frequency of free torsional vibrations for a shaft
fixed at one end and carrying a load on the free end. (8)
(ii) What is meant by torsionally equivqlent length of a shaft as referred to a stepped
shaft? Derive the expression for the equivqlent length of a shaft which has several
steps. (8)
14. (a) A vibratory body of mass 150 kg supported on springs of total stiffness 1050 kN/m
has a rotating unbalance force of 525 N at a speed of 6000 rpm. If the damping factor is
0.3,determine
i. The amplitude caused by the unbalance and its phase angle
ii. The transmissibility, and
iii. The actual force transmitted and its phase angle. (16)
OR
(b) What do you understand by transmissibility? Describe the method of finding the
transmissibility ratio from unbalanced machine supported with foundation. (16)
15. (a) The radius of rotation of the balls of a Hartnell governor is 80 mm at the minimum
speed after the sleeve has lifted by 60 mm. also determine the initial compression of the
spring, the governor effort and the power. The particulars of the governor are given
below: Length of the ball arm = 150 mm, length of sleeve arm = 100 mm, mass of each
ball = 4kg, and stiffness of the spring = 25 N/mm. (16)
OR
(b) A ship is propelled by a turbine rotor which has a mass of 5 tonnes and a speed of 2100
rpm. The rotor has a radius of gyration of 0.5 m and rotates in a clockwise direction
when viewed from the stern. Find the gyroscopic effect in the following conditions: (i)
The ship sails at a speed of 30 km/hr and steers to the left in a curve having 60m radius.
(ii) The ship pitches 60 above and 60 below the horizontal position. The bow is
descending with its maximum velocity. The motion due to pitching is simple harmonic
and the periodic time is 0 seconds. (iii) The ship rolls and at a certain instant it has an
angular velocity of 0.03 rad/s clockwise when viewed from stern.
Determine also the maximum angular acceleration during pitching. Explain how the
direction of motion due to gyroscopic effect is determined in each case. (16)
109
STUCOR
STUCOR APP
Reg .No:
B.E/B.TECH .DEGREE EXAMINATION, NOVEMBER/DECEMBER 2016

Question Paper code: 80665
Fifth semester
Mechanical
Engineering
ME 6505 – DYNAMICS OF MACHINES
(Common to Fourth Semester Mechanical Engineering (Sandwhich and Mechatronics

Engineering)
(Regulation 2013)
Time: Three hours Maximum: 100 marks
PART A – (10 X 2 =20
Marks)
1. Define inertia and inertia force.
2. What is the purpose of flywheel in an engine?
3. A flywheel has an unbalanced mass of 0.15 kg at a radius of 0.4 m from the axis of rotation.
Calculate the unbalanced force if the shaft rotates at 200 rpm.
4. What is hammer blow in locomotives?
5. What are the different types of damped vibration?
6. Define logarithmic decrement.
7. Define Vibration Isolation.
8. Write down the equation for forced vibrations.
9. Define sensitivity of governors.
10. Find the angular precession of a disc spinning on its axis at 220 rad/s, when a torque
100 N-m is applied about an axis normal to it. Mass moment of inertia of the disc is the 1
kg- m2.
PART B – (5 X 16 = 80 Marks)
11. (a) The Crank and the connecting rod of a vertical single cylinder gas engine running at 1800
rpm are 60 mm and 240 mm respectively. The diameter of the piston is 80 mm and the
mass of the reciprocating parts is 1.2 kg. At a point during the power stroke when the
piston has moved 20 mm from the top dead centre, the pressure on the piston is 800
kN/m2. Determine the
110
STUCOR
STUCOR APP
(i) Net force on the piston
(ii) Thrust in the connecting rod
(iii) Thrust on the sides of the cylinder walls
(iv) The engine speed at which the above values are zero.
Or
(b) The turning moment diagram for a multi cylinder engine has been drawn to scale 1 mm =
600 N-m vertically and 1 mm = 30 horizontally. The intercepted areas between the output
torque curve and the mean resistance line, taken in order from one end, are as follows:
+52, -124,+92, -140, +85, -72 and +107 mm2, when the engine is running at a speed of 600
r.p.m. If the total fluctuation of speed is not to exceed ± 1.5 % of the mean, find the
necessary mass of the flywheel of radius 0.5 m.
12. (a) (i) Difference between static and dynamic balancing. (4)
(ii) A circular disc mounted on a shaft carries three attached masses 4 kg, 3 kg and 2.5
kg at radial distances 75 mm, 85 mm and 50 mm and at the angular positions of
450, 1350 and 2400 respectively. The angular positions are measured counter
clockwise from the reference line along x-axis. Determine the amount of the
counter mass at a radial distance of 75 mm required for the static balance. (12)
Or
(b) An inside cylinder locomotive has its cylinder centre lines 0.7 m apart and has a stroke of
0.6 m. The rotating masses per cylinder are equivalent to 150 kg at the crank pin, and the
reciprocating masses per cylinder to 180 kg. The wheel centre lines are 1.5 m apart. The
cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses
are to b e balanced by masses are to be balanced by masses placed at a radius of 0.6 m.
Find the magnitude and direction of the balancing masses.
13.(a) A gun is so designed that on firing the barrel recoils against a spring. A dash pot at the
end of the recoil, allows the barrel to come back to its initial position within the minimum
time without any oscillation. The gun barrel has a mass of 500 kg and a recoil spring of
300 N/mm. The barrel recoils 1 m on firing. Determine:
(i) The initial velocity of the gun barrel, and (8)
(ii) The critical damping co-efficient of the dash pot engaged at the end of the recoil
stroke. (8)
Or
(b) The following data relate to a shaft held in long bearings.
Length of the shaft - 1.2 m
Diameter of the shaft - 14 mm
111
STUCOR
STUCOR APP
Mass of a rotor at midpoint - 16 kg
Eccentricity of centre of mass of rotor from centre of rotor - 0.4 mm
Modulus of elasticity of shaft material - 200 GN/mm2
Permissible stress in shaft material - 70 x 106 N/mm2
Determine the critical speed of the shaft and the range of the speed over which it is unsafe
to run the shaft. Assume the shaft to be mass less.
14. (A) A single cylinder vertical diesel engine has a mass of 400 kg and is mounted on a steel
chassis frame. The static deflection owing to the weights of the chassis is 2.4 mm. the
reciprocating mass of the engine amounts to 18 kg and the stroke of the engine is 160 mm.
a dashpot with a damping coefficient of 2 Ns/mm is also used to dampen the vibrations. In
the steady state of the vibrations, determine:
(i) The amplitude of the vibrations if the driving shaft rotates at 500 rpm
(ii) The speed of the driving shaft when the resonance occurs.
Or
(b) The mass of an electric motor is 120 kg and it runs at 1500 r.p.m. The armature mass is 35
kg and its C.G lies 0.5 mm from the axis of rotation. The motor is mounted on five springs
of negligible damping so that the force transmitted is one - eleventh of the impressed
force. Assume that the mass of the motor is equally distributed among the five springs.
Determine :
(i) stiffness of each spring;
(ii) dynamic force transmitted to the base at the operating speed; and
(iii) natural frequency of the system.
15.(a) In porter governor, each of the four arms is 400 mm long. The upper arms are pivoted on
the axis of the sleeve, whereas the lower arms are attached to the sleeve at a distance of
45 mm from the axis of the rotation. Each ball has a mass of 8 kg and the load on the
sleeve is 60 kg. What will be the equilibrium speeds for the two extreme radii of 250 mm
and 300 mm of rotation of the governor balls?
Or
(b)A four wheeled motor car of mass 200kg has a wheel base 2.5 m, track width 1.5 m and
height of centre of gravity 500 mm above the ground level and lies at 1 m from the front
axle. Each wheel has an effective diameter of 0.8 m and a moment of inertia of 0.8 kg-m 2.
The drive shaft, engine flywheel and transmission are rotating at 4 times the speed of road
wheel, in a clockwise direction when viewed from the front, and is equivalent to a mass of
75 kg having a radius of gyration of 100 mm. if the car is taking a right turn of 60 m radius
at 60km/h, find the load on each wheel.
112
STUCOR
STUCOR APP
Reg .No:
Question
B.E/B.TECH Paper
.DEGREE code: 72157
EXAMINATION, APRIL/MAY 2017
Fifth semester
Mechanical
Engineering
ME 6505 – DYNAMICS OF MACHINES
(Common to Fourth Semester Mechanical Engineering (Sandwhich and Mechatronics

Engineering)
(Regulation 2013)
Time: Three hours Maximum: 100 marks
PART A – (10 X 2 =20
Marks)
1. What is meant by piston effort?
2. List the uses of turning moment diagram?
3. Why is balancing is necessary?
4. What is hammer blow in engines with reciprocating masses?
5. Write the expression for the equivalent stiffness of two springs connected in series.
6. List the types of damping.
7. Quote two examples of forced vibration.
8. What is vibration isolation?
9. Define governor effort.
10.What is gyroscopic couple?
PART B – (5 X 16 = 80 Marks)
11. (a) The crank pin circle radius of a horizontal engine is 300 mm. The mass of the
reciprocating parts is 250 kg. When the crank has travelled 60 0 from I.D.C the difference
between centers is 1.2 m and the cylinder bore is 0.5 m. If the engine runs at 250 rpm and
if the effect of piston rod diameter is neglected, calculate the pressure on slide bars, the
113
STUCOR
STUCOR APP
thrust in the connecting rod, the tangential force on the crank pin and the turning moment
on the crank shaft.
Or
(b) The turning moment diagram for multi cylinder engine has been drawn to a vertical scale
of 1 mm = 650 Nm and a horizontal scale of 1 mm = 4.5 0. the areas above and below the
mean torque line are -28, +380, -260, +310, -300, +242,-380, +265 and -229 mm 2. The
fluctuation of speed is limited to ± 1.8 % of the mean speed which is 400 rpm. The density
of the rim material is 7000 kg/m 3 and the width of the rim is 4.5 times its thickness. The
centrifugal stress in the rim material is limited to 6 N/mm 2. Neglecting the effect of the
boss, and the arms, determine the diameter and the cross section of the flywheel rim.
12.(a) A circular disc mounted on a shaft carries three attached masses of 4 kg, 3 kg and 2.5 kg at
radial distances of 75 mm, 85 mm and 50 mm at an angular positions of 450, 1350 and
2400 respectively. The angular positions are measured counter clockwise from the
reference line along X-axis. Determine the amount of the counter mass at a radial distance
of 75 mm required for the static balance.
Or
(b) The following data refer to two cylinder with cranks at 900 reciprocating mass per
cylinder = 300 kg, crank radius = 0.3 m; driving wheel diameter = 1.8 m; distance between
cylinder centre lines = 0.65 m; distance between the driving wheel central planes = 1.55
m. determine the fraction of the reciprocating masses to be balanced, if the hammer blow
is not to exceed 46 kN at 96.5 km/hr, the variation in tractive effort and the maximum
swaying couple.
13.(a) (i)A mass of 5 kg hangs from a spring and makes damped oscillations. If the time of 50
complete oscillations is found to be 20 s, and the ratio of the first downward displacement
to the sixth is found to be 22.5, find the stiffness of the spring and the damping coefficient.
(5)
(ii) A vibrating system has the following constants: m= 17.5 kg, k= 7 N/mm and c= 70
Ns/m. Estimate the damping factor and the natural frequency of the damped free
vibrations logarithmic decrement and the ratio of any two consecutive oscillations.
(8)
Or
(b) A rotor of mass 4 kg is mounted midway on a 10 mm diameter horizontal shaft simply

supported on a span of 0.5 m. The C.G of the rotor is 0.025 mm away from the geometric
centre of the rotor. The shaft rotates at 2500 rpm. Find the amplitude of steady state
vibrations and the dynamic force transmitted to the bearings. Take E = 205 Gpa.
114
STUCOR
STUCOR APP
14.(a) A vehicle of mass 1200 kg is travelling on a road, the surface of which varies sinusoidally
with an amplitude of 0.05 m and wave length of 6 m. The suspension system has a spring
constant of 400 kN/m and a damping factor of 0.5. If the vehicle speed is 100 km/hr,
determine the displacement amplitude of the vehicle.
Or
(b) A centrifugal fan of mass 5 kg has a rotating unbalance of 0.258 kg m. When dampers
having damping factor of 0.2 are used, specify the springs for mounting such that only 10
% of the unbalance force is transmitted to the floor. The fan is running at a constant speed
of 1000 rpm.
15. (a) The arms of a porter governor are 250 mm long. The upper arms are pivoted on the axis
of revolution, but he lower arms are attached to a sleeve at a distance of 50 mm from the
axis of rotation. The weight of each ball is 80 N. determine the equilibrium speed when the
radius of rotation of the balls is 150 mm. if the friction is equivalent to a load of 25 N at the
sleeve, determine the range of speed for this position.
Or
(b)A ship is propelled by a turbine rotor of mass 500 kg and has a speed of 2400 rpm. The
rotor has a radius of gyration of 0.5 m and rotates in clockwise direction when viewed
from the stern. Find the gyroscopic effects in the following cases:
(i) The ship runs at a speed of 15 knots (1 knot = 1860 m/hr). It steers to left in a
curve of 60 m radius.
(ii) The ship pitches ± 50 from the horizontal position with the time period of 20 s of
simple harmonic motion.
(iii) The ship rolls with angular velocity of 0.04 rad/s clockwise when viewed from
stern. Also find the maximum acceleration during pitching.
PART C – (1 X 15 = 15Marks)
16.(a) The following data refer to the transmission gear of a motor ship: Moment of inertia of
flywheel is 4800 kg.m2. Movement of inertia of propeller is 3200 kg.m2, modulus of
rigidity of shaft material is 80 Gpa and assuming the diameter of the torsionally equivalent
crankshaft to be 320 mm and treating the arrangement as a three rotor system, determine
the frequency of the free torsional vibrations.
Or
(b) A governor of the proell type has each arm 250 mm long. The pivots of the upper and
lower arms are 25 mm from the axis. The central load acting on the sleeve has a mass of
25 kg and the each rotating ball has a mass of 3.2 kg. When the governor sleeve is in mid
position, the extension like of the lower arm is vertical and the radius of the path of
rotation of the masses is 175 mm. the vertical height of the governor is 200 mm. if the
governor speed is 160 rpm when in mid position, find the length of the extension link and
the tension in the upper arm.
115
STUCOR

Stucor Me8594-Wo

Uploaded by

Copyright:

Available Formats

Stucor Me8594-Wo

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Stucor Me8594-Wo

Uploaded by

Copyright:

Available Formats

DOWSNTULCOORAADPPED FROM

8. What is engine shaking force? (May /June 2013)

Velocity of the piston when θ = 400

= 188.52 rad /sec

(i) Power required to angle

From the Triangle NCP & HCD

From the Rectangle BMCN

5).The turning moment curve for an engine is represented by the equation,

Moment of inertia of flywheel (I) kg-m2

Angular acceleration of flywheel (α) ( θ =450)

Difference of pressures on two sides of the piston,

Inertia force on the reciprocating parts,

We know that net force on the piston or piston effort,

We know that crank-pin effort

2. Thrust on the bearings

3. Turning moment on the crankshaft

2. What is meant by balancing of rotating masses? (May ' 16)

5. When is a system said to be completely balanced? (May „14)

8. Define hammer blow in locomotives. (Ap/May 2017, Nov 16,

10. Define the term shaking or unbalanced force.

[NOV „ 12, May „ 14 ,NOV „ 15]

rB= 125 mm = 0.125 m mB = 10 kg

The position of planes is shown in fig.

Plane Mass Radius Centrifuga Distance Couple † ω2

b) Angular setting A = 1550 (anticlockwise Direction)

(2).The following data apply to an outside cylinder uncoupled locomotive:

Mass of rotating parts per cylinder = 360Kg ;

Plane Mass Radius(r) Centrifugal Distance Couple

From fig (c) couple polygon, by measurement

From fig (d) couple polygon, by measurement

From vector OB , by measurement

Given P = 30 kN = 30×103 N, D = 1.8 m, Balancing masses mB =mC = 249 kg

Balancing mass for reciprocating parts,

velocity = r ω = ×21.2 = 19.08 m/s =68.7 km/h

Determination of swaying couple:

swaying couple = ×m2r ω2

r = 0.3 m , l = 1.2 m, N = 240 rpm

2. Maximum secondary unbalanced force

2 & 3 = Angular position of the cranks 2& 3 with respect to crank 1

4 400 0.3 120 1.35 162

Its angular position wrt crank 1 in the counter clockwise direction is

0.3 m2 = 284 kg-m

Its angular position wrt crank 1 in the counter clockwise direction is

Determination of maximum secondary unbalanced force.

Maximum secondary unbalanced force is

Stroke L = 100 mm = 0.1 m

Speed N = 3000 rpm ; ω = = 314.2 rad/s

when  = 1200 for cylinder 2, the primary direct crank is 1200

There is no unbalanced primary force due to the reverse cranks.

Maximum primary force = r

Maximum secondary force =

Balanced by mass B2,

1) Maximum primary Force = 11.1kN

2) Maximum Secondary force = 3.7 kN.

2 = 900, = 450 , m = 11.5 kg , r = 75 mm = 0.075 m

l = 0.3 m ,N = 500 rpm, ω = = 52.37 rad/s

Maximum resultant secondary force

We known that the resultant primary force (FP)

The engine may be balanced by a rotating balanced mass.