DieselPower Lubricity

Wilhelmsen Ships Service AS

Catalogue number: 779094 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
Safety Data Sheet L.GHS.NOR.EN

SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING

Product Identifier
Product name DieselPower Lubricity

Synonyms Additive for petroleum fuels (Long chain natural fatty acids)
Other means of
779094, 779094
identification

Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses Fuel Oil Treatment

Details of the supplier of the safety data sheet

Outback (M)SDS portal:
Wilhelmsen Ships Service AS*
Registered company name Wilhelmsen Ships Service AS http://jr.chemwatch.net/outb/account
Central Warehouse
/autologin?login=wilhelmsen
--------Use our Outback portal to obtain our
(M)SDSs in other languages and/or
Strandveien 20 Lysaker 1366 format.--------- For questions relating to our Willem Barentszstraat 50 Rotterdam
Address
Norway SDSs please use Email: Netherlands
WSS.GLOBAL.SDSINFO@wilhelmsen.com
--------- Norway
Telephone +47 67 58 40 00 Not Available +31 10 4877 777

Fax Not Available Not Available +31 10 4877888

Website http://www.wilhelmsen.com/ http://www.wilhelmsen.com http://www.wilhelmsen.com
Email wss.norway.cs@wilhelmsen.com wss.global.sdsinfo@wilhelmsen.com wss.rotterdam@wilhelmsen.com

Emergency telephone number

American Chemistry Council 24hrs
Association / Organisation Giftinformasjonssentralen - 24 timer Dutch nat. poison centre
- Chemtrec
Emergency telephone
+47 22591300 +1 703 527 3887 + 31 30 274 88 88
numbers
Other emergency
Not Available +1 800 424 9300 Not Available
telephone numbers

SECTION 2 HAZARDS IDENTIFICATION

Classification of the substance or mixture

Classification according to
regulation (EC) No Not Applicable

Page 1 continued...
Catalogue number: 779094 Page 2 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

1272/2008 [CLP] [1]

Label elements

Hazard pictogram(s) Not Applicable

SIGNAL WORD NOT APPLICABLE

Hazard statement(s)
Not Applicable

Precautionary statement(s) General

P101 If medical advice is needed, have product container or label at hand.

P102 Keep out of reach of children.

P103 Read label before use.

Precautionary statement(s) Prevention

Not Applicable

Precautionary statement(s) Response

Not Applicable

Precautionary statement(s) Storage

Not Applicable

Precautionary statement(s) Disposal

Not Applicable

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

Substances
See section below for composition of Mixtures

Mixtures
CAS No %[weight] Name Classification according to regulation (EC) No 1272/2008 [CLP]
Not Available 60-100 Non classified ingredients Not Applicable

Legend: 1. Classified by Chemwatch; 2. Classification drawn from Regulation (EU) No 1272/2008 - Annex VI; 3. Classification drawn from
C&L; * EU IOELVs available

SECTION 4 FIRST AID MEASURES

Description of first aid measures

If this product comes in contact with eyes:
Wash out immediately with water.
Eye Contact
If irritation continues, seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.

If skin or hair contact occurs:

Skin Contact Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
If fumes, aerosols or combustion products are inhaled remove from contaminated area.
Inhalation
Other measures are usually unnecessary.

Immediately give a glass of water.

Ingestion
First aid is not generally required. If in doubt, contact a Poisons Information Centre or a doctor.

Indication of any immediate medical attention and special treatment needed

Treat symptomatically.

SECTION 5 FIREFIGHTING MEASURES

Extinguishing media
Foam.
Dry chemical powder.
Continued...
Catalogue number: 779094 Page 3 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

BCF (where regulations permit).

Carbon dioxide.
Water spray or fog - Large fires only.

Special hazards arising from the substrate or mixture

Fire Incompatibility None known.

Advice for firefighters

Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Prevent, by any means available, spillage from entering drains or water course.
Fire Fighting Use water delivered as a fine spray to control fire and cool adjacent area.
Avoid spraying water onto liquid pools.
DO NOT approach containers suspected to be hot.
Cool fire exposed containers with water spray from a protected location.

Combustible.
Slight fire hazard when exposed to heat or flame.
Heating may cause expansion or decomposition leading to violent rupture of containers.
Fire/Explosion Hazard
On combustion, may emit irritating/ toxic fumes.
May emit acrid smoke.
Mists containing combustible materials may be explosive.

SECTION 6 ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures

See section 8

Environmental precautions
See section 12

Methods and material for containment and cleaning up

Remove all ignition sources.
Clean up all spills immediately.
Avoid breathing vapours and contact with skin and eyes.
Minor Spills Control personal contact with the substance, by using protective equipment.
Contain and absorb spill with sand, earth, inert material or vermiculite.
Wipe up.
Place in a suitable, labelled container for waste disposal.
Moderate hazard.
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Major Spills Wear breathing apparatus plus protective gloves.
Prevent, by any means available, spillage from entering drains or water course.
No smoking, naked lights or ignition sources.
Increase ventilation.

Personal Protective Equipment advice is contained in Section 8 of the SDS.

SECTION 7 HANDLING AND STORAGE

Precautions for safe handling

Avoid all personal contact, including inhalation.
Wear protective clothing when risk of exposure occurs.
Use in a well-ventilated area.
Safe handling Prevent concentration in hollows and sumps.
DO NOT enter confined spaces until atmosphere has been checked.
Avoid smoking, naked lights or ignition sources.
Avoid contact with incompatible materials.

Store in original containers.

Keep containers securely sealed.
No smoking, naked lights or ignition sources.
Other information Store in a cool, dry, well-ventilated area.
Store away from incompatible materials and foodstuff containers.
Protect containers against physical damage and check regularly for leaks.
Observe manufacturer's storage and handling recommendations contained within this SDS.

Continued...
Catalogue number: 779094 Page 4 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

Conditions for safe storage, including any incompatibilities

Metal can or drum
Suitable container Packaging as recommended by manufacturer.
Check all containers are clearly labelled and free from leaks.
Storage incompatibility None known

+ + + + + + +

X — Must not be stored together

0 — May be stored together with specific preventions
+ — May be stored together

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

Control parameters

OCCUPATIONAL EXPOSURE LIMITS (OEL)

INGREDIENT DATA
Not Available

EMERGENCY LIMITS

Ingredient Material name TEEL-1 TEEL-2 TEEL-3

DieselPower Lubricity Not Available Not Available Not Available Not Available

Ingredient Original IDLH Revised IDLH

Non classified ingredients Not Available Not Available

MATERIAL DATA

Exposure controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed
engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to
provide this high level of protection.
The basic types of engineering controls are:
Appropriate engineering
Process controls which involve changing the way a job activity or process is done to reduce the risk.
controls
Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation
that strategically "adds" and "removes" air in the work environment. Ventilation can remove or dilute an air contaminant if
designed properly. The design of a ventilation system must match the particular process and chemical or contaminant in use.
Employers may need to use multiple types of controls to prevent employee overexposure.

Personal protection

Safety glasses with side shields

Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy
document, describing the wearing of lenses or restrictions on use, should be created for each workplace or task. This should
Eye and face protection include a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience.
Medical and first-aid personnel should be trained in their removal and suitable equipment should be readily available. In the
event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens should
be removed at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers
have washed hands thoroughly.

Skin protection See Hand protection below

Wear general protective gloves, eg. light weight rubber gloves.
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from
manufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material
can not be calculated in advance and has therefore to be checked prior to the application.
Hands/feet protection
The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and.has to be
observed when making a final choice.
Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands
should be washed and dried thoroughly. Application of a non-perfumed moisturiser is recommended.

Continued...
Catalogue number: 779094 Page 5 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

Body protection See Other protection below

No special equipment needed when handling small quantities.
OTHERWISE:
Other protection Overalls.
Barrier cream.
Eyewash unit.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties

Appearance Yellow

Relative density (Water =

Physical state Liquid 0.895
1)

Partition coefficient
Odour Slight Not Available
n-octanol / water

Auto-ignition temperature
Odour threshold Not Available 300.1
(°C)

Decomposition
pH (as supplied) Not Available Not Available
temperature

Melting point / freezing

6 Viscosity (cSt) 35.00
point (°C)
Initial boiling point and
Not Available Molecular weight (g/mol) Not Available
boiling range (°C)
Flash point (°C) 180 Taste Not Available

Evaporation rate Not Available Explosive properties Not Available

Flammability Not Applicable Oxidising properties Not Available
Surface Tension (dyn/cm
Upper Explosive Limit (%) Not Available Not Available
or mN/m)
Lower Explosive Limit (%) Not Available Volatile Component (%vol) Not Available

Vapour pressure (kPa) 0.133 Gas group Not Available

Solubility in water Immiscible pH as a solution (1%) Not Available
Vapour density (Air = 1) Not Available VOC g/L Not Available

SECTION 10 STABILITY AND REACTIVITY

Reactivity See section 7

Chemical stability Product is considered stable and hazardous polymerisation will not occur.
Possibility of hazardous
See section 7
reactions
Conditions to avoid See section 7

Incompatible materials See section 7

Hazardous decomposition
See section 5
products

SECTION 11 TOXICOLOGICAL INFORMATION

Information on toxicological effects

The material is not thought to produce adverse health effects or irritation of the respiratory tract (as classified by EC Directives
Inhaled using animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable control
measures be used in an occupational setting.
The material has NOT been classified by EC Directives or other classification systems as "harmful by ingestion". This is because
of the lack of corroborating animal or human evidence. The material may still be damaging to the health of the individual,
following ingestion, especially where pre-existing organ (e.g liver, kidney) damage is evident. Present definitions of harmful or
Ingestion
toxic substances are generally based on doses producing mortality rather than those producing morbidity (disease, ill-health).
Gastrointestinal tract discomfort may produce nausea and vomiting. In an occupational setting however, ingestion of insignificant
quantities is not thought to be cause for concern.

Continued...
Catalogue number: 779094 Page 6 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

Skin Contact The liquid may be miscible with fats or oils and may degrease the skin, producing a skin reaction described as non-allergic
contact dermatitis. The material is unlikely to produce an irritant dermatitis as described in EC Directives .

Eye Although the liquid is not thought to be an irritant (as classified by EC Directives), direct contact with the eye may produce
transient discomfort characterised by tearing or conjunctival redness (as with windburn).
Long-term exposure to the product is not thought to produce chronic effects adverse to health (as classified by EC Directives
Chronic
using animal models); nevertheless exposure by all routes should be minimised as a matter of course.

TOXICITY IRRITATION
DieselPower Lubricity
Oral (rat) LD50: >2000 mg/kg[2] Not Available

TOXICITY IRRITATION
Non classified ingredients
Not Available Not Available

Legend: 1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2.* Value obtained from manufacturer's SDS.
Unless otherwise specified data extracted from RTECS - Register of Toxic Effect of chemical Substances

Acute Toxicity Carcinogenicity

Skin Irritation/Corrosion Reproductivity

Serious Eye
STOT - Single Exposure
Damage/Irritation

Respiratory or Skin
STOT - Repeated Exposure
sensitisation
Mutagenicity Aspiration Hazard

Legend: – Data either not available or does not fill the criteria for classification
– Data available to make classification

SECTION 12 ECOLOGICAL INFORMATION

Toxicity

ENDPOINT TEST DURATION (HR) SPECIES VALUE SOURCE

DieselPower Lubricity
LC50 96 Fish Other >100mg/L 8

ENDPOINT TEST DURATION (HR) SPECIES VALUE SOURCE

Non classified ingredients Not Not Not
Not Available Not Available
Available Available Available

Legend: Extracted from 1. IUCLID Toxicity Data 2. Europe ECHA Registered Substances - Ecotoxicological Information - Aquatic Toxicity
3. EPIWIN Suite V3.12 (QSAR) - Aquatic Toxicity Data (Estimated) 4. US EPA, Ecotox database - Aquatic Toxicity Data 5.
ECETOC Aquatic Hazard Assessment Data 6. NITE (Japan) - Bioconcentration Data 7. METI (Japan) - Bioconcentration Data 8.
Vendor Data

Harmful to aquatic organisms.

Persistence and degradability

Ingredient Persistence: Water/Soil Persistence: Air

No Data available for all ingredients No Data available for all ingredients

Bioaccumulative potential
Ingredient Bioaccumulation

No Data available for all ingredients

Mobility in soil
Ingredient Mobility

No Data available for all ingredients

Continued...
Catalogue number: 779094 Page 7 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

SECTION 13 DISPOSAL CONSIDERATIONS

Waste treatment methods

Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws
operating in their area. In some areas, certain wastes must be tracked.
A Hierarchy of Controls seems to be common - the user should investigate:
Reduction
Reuse
Recycling
Disposal (if all else fails)
This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. If it
has been contaminated, it may be possible to reclaim the product by filtration, distillation or some other means. Shelf life
Product / Packaging
considerations should also be applied in making decisions of this type. Note that properties of a material may change in use, and
disposal
recycling or reuse may not always be appropriate.
DO NOT allow wash water from cleaning or process equipment to enter drains.
It may be necessary to collect all wash water for treatment before disposal.
In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first.
Where in doubt contact the responsible authority.
Recycle wherever possible or consult manufacturer for recycling options.
Consult State Land Waste Management Authority for disposal.
Bury residue in an authorised landfill.
Recycle containers if possible, or dispose of in an authorised landfill.

SECTION 14 TRANSPORT INFORMATION

Labels Required
Marine Pollutant NO

Land transport (ADR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS

Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS

Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS

Inland waterways transport (ADN): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS

Transport in bulk according to Annex II of MARPOL and the IBC code

Not Applicable

SECTION 15 REGULATORY INFORMATION

Safety, health and environmental regulations / legislation specific for the substance or mixture

NON CLASSIFIED INGREDIENTS IS FOUND ON THE FOLLOWING REGULATORY LISTS

Not Applicable

National Inventory Status

National Inventory Status
Australia - AICS Yes

Canada - DSL Yes

Canada - NDSL Yes

China - IECSC Yes

Europe - EINEC / ELINCS /

Yes
NLP

Japan - ENCS Yes

Korea - KECI Yes

New Zealand - NZIoC Yes

Philippines - PICCS Yes

USA - TSCA Yes

Taiwan - TCSI Yes

Mexico - INSQ Yes

Vietnam - NCI Yes

Continued...
Catalogue number: 779094 Page 8 of 8 Issue Date: 22/01/2019
Version No: 1.5 Print Date: 19/04/2020
DieselPower Lubricity

Russia - ARIPS Yes

Yes = All CAS declared ingredients are on the inventory
Legend: No = One or more of the CAS listed ingredients are not on the inventory and are not exempt from listing(see specific ingredients
in brackets)

SECTION 16 OTHER INFORMATION

Revision Date 22/01/2019

Initial Date 01/10/2018

CONTACT POINT
- For quotations contact your local Customer Services - http://wssdirectory.wilhelmsen.com/#/customerservices - - Responsible for safety data sheet Wilhelmsen
Ships Service AS - Prepared by: Product HSE Manager, - Email: Email: WSS.GLOBAL.SDSINFO@wilhelmsen.com - Telephone: Tel.: +31 10 4877775

Other information
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch
Classification committee using available literature references.

The SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks
in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available
engineering controls must be considered.

For detailed advice on Personal Protective Equipment, refer to the following EU CEN Standards:
EN 166 Personal eye-protection
EN 340 Protective clothing
EN 374 Protective gloves against chemicals and micro-organisms
EN 13832 Footwear protecting against chemicals
EN 133 Respiratory protective devices

Definitions and abbreviations

PC－TWA: Permissible Concentration-Time Weighted Average
PC－STEL: Permissible Concentration-Short Term Exposure Limit
IARC: International Agency for Research on Cancer
ACGIH: American Conference of Governmental Industrial Hygienists
STEL: Short Term Exposure Limit
TEEL: Temporary Emergency Exposure Limit。
IDLH: Immediately Dangerous to Life or Health Concentrations
OSF: Odour Safety Factor
NOAEL :No Observed Adverse Effect Level
LOAEL: Lowest Observed Adverse Effect Level
TLV: Threshold Limit Value
LOD: Limit Of Detection
OTV: Odour Threshold Value
BCF: BioConcentration Factors
BEI: Biological Exposure Index

Powered by AuthorITe, from Chemwatch.

end of SDS