Hydro Gloss Solid Wood

TECHNICAL DATA SHEET
HYDRO-GLOSS Updated Feb’20
Hydro-Gloss is an environmental friendly green product with low VOC (Volatile Organic Compound)
for interior use. It is formulated with a solvent-free resin to limit air pollutants and has an extremely
low odour during application and drying. Being a green product, it is ideal for use in eco-sensitive
commercial and residential areas such as hospitals, schools, residential buildings and hotels. It is
easy to apply and forms a tough paint film with durability and smooth finishing.
Hydro-Gloss special formulated with Dry film Anti-bacterial property which protects the
environment from bacteria such as MRSA, E-Coli and Staphylococcus Aureus.
Product Features:
• Environmental-friendly green paint for wood and metal substrate
• Low VOC
• Easy application
• Fungus resistance
• Excellent coverage and hiding power
Paint Type Product Finishing Recommended Substrate Pack Size

Type
Water based Interior High Gloss Wood and Metal 1 Litre, 5 Litres
Composition
Pigment : Mainly Titanium Dioxide, Iron Oxide, Carbon Black, Organic Pigments
Binder : Ambient Cross-linking Acrylic Polymer
Thinner : Water
Technical Data
Drying Time : Touch Dry : 30 minutes
: Hard Dry : 1 hour
Drying time above is based on temperature 28 – 32 °C, humidity 70 – 80%
Recoating Time : 2 – 3 hours (minimum)
Recoating time above is based on temperature 28 – 32 °C, humidity 70 – 80%
*Important Note:
Drying Time and recoating time are strongly depending on environment ventilation, paint thickness, environment
temperature, environment humidity, number of coats applied. So drying time and recoating time provided is for guide
only.
Dry Film Thickness : 30 – 40 µm per coat (based on substrate condition)
No. of Coats : 2 – 3 coats
Theoretical Coverage : 9 – 11 m2 per litre per coat (Actual coverage is dependent on substrate condition, application
method, application condition and finishing appearance).
Volume Solid : ~ 40%
Shelf Life : Up to 36 months in tight sealed container
Application Method
Brush / Roller : The paint is ready for use after thorough stirring. Dilute the paint with 5% of Water, if necessary.
Recommend to use Nippon Synthetic Brush or Nippon WB 4 Inch Roller for application.
Conventional Air Spray : Dilute the paint with 5% - 10% of water if necessary
Recommended Coating System

Wood, Steel and Iron
Sealer / Primer : Hydro-Primer : 1 Coat
Top Coat : Hydro-Gloss : 2 – 3 Coats
P a g e 1|2
TECHNICAL DATA SHEET
Aluminium and Galvanized Iron
Etching Primer : Etching Primer 120 : 1 coat
Sealer / Primer : Hydro-Primer : 1 Coat
Top Coat : Hydro-Gloss : 2 – 3 Coats
Surface Preparation
Wood
Wood must be dry and free from dirt, grease and other contaminants. Smoothen surface with sand paper, then clean off
and dry.
Metal
Surface must be dry and free from dirt, grease and other contaminants. Ferrous substrate should be sanded or wire-brushed
to remove millscales and rust. Clean off dust and dry.
Scrap off any loose and flaking paint film. Sand and smoothen defective areas. The entire surface must be dry and free from
dirt, grease and other contaminants. For the case of ferrous substrates, remove rust thoroughly. The scraped areas should
be spot-primed. Light sanding on surface would ensure better subsequent intercoat adhesion.
Cleaning
Clean up equipment with water immediately after use.
Safety Precautions
• Keep container tightly closed and keep out of reach children or away from food and drink.
• Ensure good ventilation during application and drying.
• When applying paint, it is advisable to wear eye protection.
• In case of contact with eye, rinse with plenty of water immediately and seek medical advice.
• Remove splashes from skin by using soap or water.
• Paint must always be stored in a cool place.
• When transporting paint, care must be taken. Always keep container in a secure upright position.
• Dispose any paint waste in accordance with the appropriate Environment Quality Regulations.
Note
* Theoretical Coverage is based on a mathematical formula
𝑉𝑜𝑙𝑢𝑚𝑒 𝑆𝑜𝑙𝑖𝑑 % 𝑥 10
[ ] = m2/lit/coat
𝐷𝑟𝑦 𝐹𝑖𝑙𝑚 𝑇ℎ𝑖𝑐𝑘𝑛𝑒𝑠𝑠
and does not consider LOSS FACTORS.

Variables like porosity of substrate, application method, dilution ratio, dry film thickness, opacity and so on will affect the
loss factor and can vary from 30% - 50% or even more.
The above information is given to the best of our knowledge based on laboratory tests and practical experience.
However, since we cannot anticipate or control the many conditions under which our products may be used, we can only
guarantee the quality of the product itself.
We reserve the right to alter the given without prior notice.
P a g e 2|2

Hydro Gloss Solid Wood

Uploaded by

Copyright:

Available Formats

Hydro Gloss Solid Wood

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hydro Gloss Solid Wood

Uploaded by

Copyright:

Available Formats

TECHNICAL DATA SHEET

HYDRO-GLOSS Updated Feb’20

Paint Type Product Finishing Recommended Substrate Pack Size

Recommended Coating System

and does not consider LOSS FACTORS.

You might also like