Original

16” (40cm) Stand Fan with Remote Control
Instruction Manual
AKSF-40BK
WARNING To reduce the risk for fire, electric shock or personal injury
• Do not use this fan with any solid-state speed control device.
• Unplug the fan before cleaning or servicing.
• To reduce the risk of electric shock and injury to persons, do not use in window.
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS

This fan is for residential use only. It is not intended for use in commercial or industrial
settings.
Important instructions
Read and save these important safety - Arrange cord away from traffic area and
instructions before using this fan, when where it will not be tripped over.
using electrical appliances, basic safety
precautions should always be followed
including the following:
Assembly
1. Place the base on a flat
surface. Remove the
WARNING - To reduce the risk of fire or
electrical shock, do not use this product locking mechanism from
with any solid state speed control device. the pole and insert the pole
To reduce the risk of fire or electric shock onto the base.
and injury to persons, do not use in a 2. Turn over the base with the
window. pole inserted and secure by
turning the locking
- Use this fan only as described in this mechanism clockwise until completed
fastened.
manual. Other uses not recommended
3. Place the motor assembly and
may cause fire or electric shock.
control panel onto the extension pole
- This product is intended for and secure by turning the assembly
HOUSEHOLD USE ONLY and not for knob clockwise.
commercial, industrial or outside use. To 4. Remove the rear grill mounting nut
protect against electrical shock, do not by turning it counter-clockwise.
place fan in window, immerse unit, plug
or cord in water, or spray with liquids. 5. Place the rear grill onto
- Unplug the fan from the outlet when not the motor housing
in use, when moving fan from one aligning the 3 raised
location to another and before cleaning. knobs on the top of the
- Do not operate the fan in the presence motor housing with the
of explosive and/or flammable fumes. 3 holes on the grill.
- Do not place the fan or any parts near 6. Place the rear grill
an open flame, cooking or other heating mounting nut and
appliance. tighten turning clockwise.
- Avoid contact with moving fan parts. 7. Align the blade onto the
- shaft and secure it by
To disconnect, grip the plug and pull it
from the wall outlet. Never yank the tightening the blade
cord. knob counter-clockwise.
- 8. Fix the front grill and the
The use of attachments is not
recommended and may cause hazards. rear grill with the circlip
- and fasten the ring
Always use on a dry, level surface.
around the grill. You will
- Do not operate if the fan housing is hear a click sound
removed or damaged. around the grill.
- Discard fan or return to an authorized 9. Then use the fasten clip
service facility for examination and/or to tighten the fan grill.
repair.
10. Secure further with the
- Do not run cord under carpeting. Do screw and tighten with a
not cover cord with throw rugs, runners, screw driver.
or similar coverings. Do not route cord
under furniture or appliances.
How to operate
2
1. Make sure that the fan is on a firm, 4. Do not immerse the fan in water and
level surface. never allow water to enter the Motor
2. Making sure the speed control is at Housing.
OFF position. 5. Do not use gasoline, paint thinner or
3. Plug the power cord into the socket. other chemicals to clean the fan.
4. Plug the cord set into the outlet.
On/Off:
To turn fan on, press the Power button.
Sound Level/Speed Control:

Press the Fan button repeatedly to
change level. This fan has up to five
speeds to select from.
Auto-off Timer:
This setting will automatically turn your
fan off after 2, 4, or 8 hrs.
1 hour: Press one time

2 hours: Press two times
4 hours: Press three times
8 hours: Press four times
Turn Timer off: Press five times or
press power button
5. Oscillation can be activated by pushing

the bar downward and the fan can be
made to operate in a stationary position
by gently pulling the knob.
Remote control
1. Install batteries (not supplied) as
shown. The battery is size “AAA”.
2. All the functions performed with
the Remote-Control work
identically to the Manual Controls.
3. Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel- cadmium) batteries.
4. DO NOT DISPOSE OF BATTERIES IN FIRE.
BATTERIES MAY EXPLODE OR LEAK.
Cleaning
1. Be sure your fan is in the OFF position.
2. Unplug the fan before cleaning.
3. Use only a soft, damp cloth to gently
wipe the fan.
3
Description of parts
1. Front grill
2. Grill protective ring
3. Blade knob
4. Blade
5. Rear grill mounting nut
6. Rear grill
7. Shaft
8. Motor assembly
9. Oscillating pin
10. Remote storage
11. Control panel
12. Inner pole
13. Height adjuster
14. Outer pole
15. Base
16. Base locking mechanism
17. Remote control
18. Fasten clip
Technical Specifications
Model: AKSF-40BK
Power Supply: 220-240V~ 50Hz
Rated Power: 50W
Class II
Conforms to all relevant

European Directives.

Original

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Original

Uploaded by

Copyright:

Available Formats

16” (40cm) Stand Fan with Remote Control

PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS

Sound Level/Speed Control:

1 hour: Press one time

5. Oscillation can be activated by pushing

Conforms to all relevant

You might also like