TOSHIBA BIPOLAR LINEAR INTEGRATED CIRCUIT INTEGRATED CIRCUIT TA8205AH, TA8205AL TOSHIBA TECHNICAL DATA SILICON MONOLITHIC 18W BTLx2CH AUDIO POWER AMPLIFIER The thermal resistance 6j-T of TA8205AH, TA8205AL TARZOSAR package designed for low thermal resistance, has a high = efficiency of heat radiation. ‘The temperature rise of chip can be reduced, and the influence from the degradation of the features due to ‘the temperature rise at the high output can also be reduced. This stereo audio power IC, designed for car audio use, has two built-in channels to reduce the characteristic difference between L and R channels. In addition, the functions of stand-by and muting, and a variety of protection circuits are involved. FEATURES © Low Thermal Resistance 6)-T = 1.5°C/W (Infinite Heat Sink) eee © High Power weight H2RI7E : 289 (yp) Pour (1) = 18W (Typ.)/Channel (Wec= 14.4v, f=1kHz, THD = 10%, R, =4) Pour (2) = 15W (Typ.)/Channel (ec= 13.2V, f=1kHz, THD = 10%, &, =4) © Low Distortion Ratio : THD=0.04% (Typ.) (Vec=13.2V, f= 1kHz, PoUT=1W, RL=40, Gy=50dB) © Low Noise : Vo =0.30mVrms (Typ) (Vec=13.2V, RL =42, Gy=50dB, Rg =00, BW =20H2~20kH2) © Built-in Stand-by Function (With pin@ set at LOW, power is turned OFF.) : Isp= 1A (Typ.) '® Built-in Muting Function (With pin@) set at Low, power is turned OFF.) : V (Mute) =1V (Typ.) © Built-in Various Protection Circuits Protection circuits : Thermal Shut Down, over voltage, out-»Vcc short, out-sGND short and OUT- OUT Short © Operating Supply Voltage : Vec=9~18V TAS205AH— ° (9966-17 TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TECHNICAL DATA BLOCK DIAGRAM TAB205AH, TAS20SAL (Gy TA8205AH, TA8205AL $9) aro sw PROTECTOR Cove-on) Pregho —_ Sangy SW CAUTIONS AND APPLICATION METHOD (Description is made only on the single channel.) 1. Voltage gain adjustment a amp 3. Amp 422008 Bi) Fig.1 frowerony ‘amp 3 POWER Amp (FatAmp) ‘Amp & POWER Amp (FatAMP) This IC has the amplifier construction as shown in Fig.1. The Pre-Amp. Amp 1 is provided to the primary stage, and the input voltage is amplified by the Flat Amps, Amp 3 and Amp 4 of each channel through the phase Amp. Amp 2. Since the input offset is prevented by Pre-Amp when Vcc is set to ON, this circuit can remarkably reduce the pop noise, TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA ‘The total closed loop gain Gy of this IC can be obtained by expression below when the closed loop voltage gain of Amp 1 is Gyy Gy1=2080g neem (a8) The closed loop voltage gain of POWER Amp, Amp 3 and Amp 4 is fixed at Gy3=Gyg=20d8 Therefore, the total closed circuit voltage gain Gy is a obtained through BTL connection by the expression below. al Gy=Gy1 + Gy3 +6 (da) Q g For example, when Ry=02, Gy is obtained by the = al expressions (1) and (2) as shown below. zg Gy24+20+6=50d8 g The voltage gain is reduced when Ris increased. (Fig.2) 3 With the voltage gain reduced, since (1) the oscillation ~ | stability is reduced, and (2) the pop noise changes when Vcc is set to ON, refer to the items 3 and 4 d FEEDBACK RESISTANCE (0) Fig2 2. Stand-by SW function By means of controlling pind) (Stand-by terminal) to High and Low, the power supply can be set to ON and OFF. i The threshold voltage of pin‘ is set at about 3V (Typ), “ and the Power Supply current is about 1A (Typ.) at the ‘on brower | r0ict stand-By state Pr fe Pin@ control voltage : Visa) aren Gre stanp-8y | POWER | Visa) () ON OF O=2 OFF ON 3Vee Fig.3 With pind set to High, Power is turned ON. Advantage of stand-by SW (1) Since Ve¢ can directly be controlled to ON/OFF by the microcomputer, the switching relay can be omitted, (2) Since the control current is microscopic, the switching relay of small current capacity is, satisfactory for switching. {eee 9G = = 1 ee TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA Leto cert enn ten (Conventional Method) 0. cart apa ch Bret tom mire owe (Standby Switch Method) 3. Preventive measure against oscillation For preventing the oscillation, it is advisable to use C4, the condenser of polyester film having small characteristic fluctuation of the temperature and the frequency ‘The resistance R to be series applied to Cg is effective for phase correction of high frequency, and improves the oscillation allowance. Since the oscillation allowance is varied according to the causes described below, perform the ‘temperature test to check the oscillation allowance. (1) Voltage gain to be used (Gy Setting) (2) Capacity value of condenser () kind of condenser (4) Layout of printed board In case of its use with the voltage gain Gy reduced or with the feedback amount increased, care must be taken because the phase-inversion is caused by the high frequency resulting in making the oscillation generated 4, Input offset prevention circuit at Vec-ON Having Pre-Amp (Amp 1) mounted on the primary stage, this IC contains the circuit for making the ‘Amp 1 input voltage and the NF terminal voltage equipotential Therefore, the offset voltage produced at the input stage is suppressed to prevent the pop noise at Vcc-ON. The capacity values of the input and NF condenser (C1 and C3) shall be set according to the gain to be used (Reference) (A)At Gy =50d8 (Ry =02) C14. 7uF, C2=47 uF (8) At Gy =40dB (Ry=4700) C1=3.3MF, C2=33F TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA 5, Muting function Through setting pin@® (mute terminal) at about 1V or less, muting becomes possible. The interval circuit of IC is shown in Fig.4 When pin® is set to LOW, Q1 and Q2 are turned to ON, the charge of the ripple condenser is, discharged and the bias is cut. The mute amount of 60dB or over can be obtained Since this mute function rapidly discharges the charge of the ripple filter capacitor of pin®, the pop noise is generated by the DC fluctuation of the bias section. Therefore, this muting function is not appropriate to the audio muting but it is effective in muting at VecON. 6._External parts list and description fy, RB TKR Raei04d Fig.4 Mute circuit Name | RECOM. INFLUENCE OF | MENDED | OBJECT SMALLER THAN LARGER THAN REMARKS PART | VALUE RECOMMENDED VALUE | RECOMMENDED VALUE Rela in cr | a7ae ]oc blocking — [Related to pop noise at Vcc0N. er een elated to pop noise at Voc SON an Determination of low cut-off frequency. co | ae 1 condenser = ArfURE | azar [Ripple Time constant is small [Time constant is large 3 eF [reduction at Vec0N or OFF. _| at Vec->0N or OFF. lation Made Tiabl lation allowani ca O.12pF Oscillatior lade liable to ‘Oscillation allowance Refer to item 3. prevention | oscillate. improved For filtering power supply hum and ripple. 5 | 1000, |Ripple fier | Large at using AC rectified power supply small at using DC power supply. TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA MAXIMUM RATINGS (Ta = 25°C) CHARACTERISTIC symeo. | RATING | UNIT Peak Supply Vonage (025) | Vec urge) 50 v DC Supply Voltage Vec(00) 25 Vv Operating Supply Vokage | Vcc opn 18 Vv Output Current (Peak) To (peak) 3 A Power Dissipation Pp 50 Ww Operating Temperature Tope =30~85_| “C Storage Temperature Tag =55~150 | *€ ELECTRICAL CHARACTERISTICS (Unless otherwise specified, Vec kHz, Ta =25°C) CHARACTERISTIC symsot |cur-| Test CONDITION — | min. | TYP. | Max. | UNIT cur Quiescent Supply Current Tecq | — [Vin =] 120 [250 [ma Pour | — |Vcc=14av, THD=10% | — | 18] — eaeat esas Pout @) | — [THD= 10% ais; — | ™ Total Harmonic Distortion tHo | — |Pour=1w = 4 | 04 Ratio ‘out 0.04] 04} % Voltage Gain Gy = = | 50] 52] a8 Rg=00, Output Noise Voltage Woe lees ee — | 0.30 | 0.70 |mVsms ‘ripple = 100H2, Ripple Rejection Ratio RR = |rg=soon ao} sa} — | ap Input Resistance Rin | — = =| | — [eo Output Offset Voltage Vottset | — [Vin =03 [| o[ 03 | mv Current at Stand-by State isp 7 = = ee Ry = 6000, Cross Talk cr. — |Vout=0.775Vems S| a|-|a (dBm) Stand-by OFF Pin@ Control Voltage ole 25| — | vec} v MuteON Pin Control Voltage Vewuted | — [power soe — | .w] 20] v TAB205AH—6 [1996-617 TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA TEST CIRCUIT TA8205AH, TAB205AL (Gy = 50d8) iene omer on) TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA THD - Pour THD - Pout 19} asl «| TOTAL HARMON OITORNION THD. () TOTAL MASHONE OBTORTION THD. (H) a a = a ae Soeeesseast maces 2S OO 0 or est ar Een . A : a Q no i 5 z vee= 1320 S05] e ol i Ea Ea 3 ost Z g i. i i. oo 2 TAS205AI TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA RR Af Ywo - Rg g 2 Bole | eects g 8 2 : = g 8 2 & & E . 8 rraquiner + 609 Sona SURCERESHTANEE Ag 10) AR Ry Pour _ "Vienne go) Moan : 5 g é 3 5 3 : : 3 a 3 ea Sona SOURCE RESSTANCE Ay (@ sneQUENcr + 0a) 0 = Pour t-te nal, fotkie z D wane wear anc nics sew >| io - a @ vearane inicrse 5 oun. oreranon [Yee e noice © Wo wear senor i ji ga 3 5 é i 4 § : ! H & |e i g 4 2 r § fete ry y « ® Ww 6 2 °D 1 200, court rower Pour 6 Am TPERATURE Ta CO TAS205AI TOSHIBA CORPORATIONINTEGRATED CIRCUIT TOSHIBA TA8205AH, TA8205AL TECHNICAL DATA OUTLINE DRAWING HZIP17-P Unit : mm i f 149102 Ey 3 17.0103, 10.0108 | f | 5.0203 2.5751 36.5AX. 96.0102 1 7 Weight : 9.89 (Typ.) TAS205AH — 10 {eee 9G = = 1 ee TOSHIBA CORPORATIONINTEGRATED CIRCUIT TA8205AH, TA8205AL TOSHIBA TECHNICAL DATA OUTLINE DRAWING a — 4 , by | Eee ¢ 3 gl 3 te) * ale di | | al 2.5751vP 2.0TYP, .t 7 az A 0.493 oss grasa _| {120 ie 9) sssun Weight : 9.89 (Typ.) TOSHIBA CORPORATION