VV-65B-R1B Product Specifications

VV-65B-R1B
4-port sector antenna, 4x 1695–2690 MHz, 65° HPBW, 1x RET and

internal Bias-T on first highband port. The two highband arrays utilize a
common tilt.
The RET interface comprises one pair of AISG input/output ports
OBSOLETE
This product was discontinued on: March 31, 2021
Replaced By:
VV-65B-R1B-V2 4-port sector antenna, 4x 1695–2690 MHz, 65° HPBW, 1x RET and internal Bias-T on first highband
port. The two highband arrays utilize a common tilt.
General Specifications
Antenna Type Sector
Band Single band
Grounding Type RF connector body grounded to reflector and mounting bracket
Performance Note Outdoor usage
Radome Material PVC
RF Connector Interface 7-16 DIN Female
RF Connector Location Bottom
RF Connector Quantity, high band 4
RF Connector Quantity, total 4
Remote Electrical Tilt (RET) Information

RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 1 female | 1 male
Input Voltage 10–30 Vdc
Internal Bias Tee Port 1
Internal RET High band (1)
Power Consumption, idle state, maximum 2W
13 W Page 1 of 5
©2022 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: August 12, 2022
VV-65B-R1B
Power Consumption, normal conditions, maximum 13 W
Protocol 3GPP/AISG 2.0 (Single RET)
Dimensions
Width 305 mm | 12.008 in
Depth 118 mm | 4.646 in
Length 1786 mm | 70.315 in
Net Weight, without mounting kit 13.4 kg | 29.542 lb
Array Layout
Port Configuration
Page 2 of 5
VV-65B-R1B
Electrical Specifications
Impedance 50 ohm
Operating Frequency Band 1695 – 2690 MHz
Polarization ±45°
Total Input Power, maximum 400 W @ 50 °C
Electrical Specifications
Frequency Band, MHz 1695–1880 1850–1990 1920–2200 2300–2500 2500–2690
Gain, dBi 18.3 18.9 19.4 19.1 19.5
Beamwidth, Horizontal, 66 66 61 61 57
degrees
Beamwidth, Vertical, degrees 5.6 5.2 4.3 4.3 4.1
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 19 19 17 17 18
Front-to-Back Ratio at 180°, 32 34 35 35 36
dB
Isolation, Cross Polarization, 30 30 30 30 30
dB
Isolation, Inter-band, dB 30 30 30 30 30
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
-153 -153 -153 -153 -153 Page 3 of 5
VV-65B-R1B
PIM, 3rd Order, 2 x 20 W, dBc -153 -153 -153 -153 -153
Input Power per Port, 350 350 350 350 300
maximum, watts
Electrical Specifications, BASTA

Frequency Band, MHz 1695–1880 1850–1990 1920–2200 2300–2500 2500–2690
Gain by all Beam Tilts, 17.9 18.5 19.1 19.1 19.2
average, dBi
Gain by all Beam Tilts ±0.5 ±0.4 ±0.4 ±0.4 ±0.5
Tolerance, dB
Gain by Beam Tilt, average, 2 ° | 17.8 2 ° | 18.3 2 ° | 19.0 2 ° | 19.0 2 ° | 19.2
dBi 7 ° | 18.0 7 ° | 18.6 7 ° | 19.3 7 ° | 19.3 7 ° | 19.5
12 ° | 17.8 12 ° | 18.3 12 ° | 18.6 12 ° | 18.6 12 ° | 18.7
Beamwidth, Horizontal ±2.9 ±1.7 ±2.6 ±2.6 ±4.3

Tolerance, degrees
Beamwidth, Vertical ±0.3 ±0.3 ±0.2 ±0.2 ±0.2
Tolerance, degrees
USLS, beampeak to 20° above 16 16 15 15 13
beampeak, dB
Front-to-Back Total Power at 25 25 27 27 26
180° ± 30°, dB
CPR at Boresight, dB 16 18 21 21 19
CPR at Sector, dB 10 10 8 8 9
Mechanical Specifications
Wind Loading @ Velocity, frontal 696.0 N @ 150 km/h (156.5 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral 163.0 N @ 150 km/h (36.6 lbf @ 150 km/h)
Wind Loading @ Velocity, rear 761.0 N @ 150 km/h (171.1 lbf @ 150 km/h)
Wind Speed, maximum 241 km/h | 149.75 mph
Packaging and Weights

Width, packed 410 mm | 16.142 in
Depth, packed 270 mm | 10.63 in
Length, packed 1955 mm | 76.969 in
Weight, gross 24 kg | 52.911 lb
Regulatory Compliance/Certifications
Agency Classification
CE Compliant with the relevant CE product directives
Page 4 of 5
VV-65B-R1B
CHINA-ROHS Above maximum concentration value
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
ROHS Compliant/Exempted
Included Products
BSAMNT-3 – Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members.
Kit contains one scissor top bracket set and one bottom bracket set.
* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance
Page 5 of 5

VV-65B-R1B Product Specifications

Uploaded by

Copyright:

Available Formats

VV-65B-R1B Product Specifications

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VV-65B-R1B Product Specifications

Uploaded by

Copyright:

Available Formats

VV-65B-R1B

4-port sector antenna, 4x 1695–2690 MHz, 65° HPBW, 1x RET and

The RET interface comprises one pair of AISG input/output ports

Band Single band

Grounding Type RF connector body grounded to reflector and mounting bracket

Performance Note Outdoor usage

Radome Material PVC

RF Connector Interface 7-16 DIN Female

RF Connector Location Bottom

RF Connector Quantity, high band 4

RF Connector Quantity, total 4

Remote Electrical Tilt (RET) Information

RET Interface, quantity 1 female | 1 male

Input Voltage 10–30 Vdc

Internal Bias Tee Port 1

Internal RET High band (1)

Power Consumption, idle state, maximum 2W

Protocol 3GPP/AISG 2.0 (Single RET)

Depth 118 mm | 4.646 in

Length 1786 mm | 70.315 in

Net Weight, without mounting kit 13.4 kg | 29.542 lb

Operating Frequency Band 1695 – 2690 MHz

Total Input Power, maximum 400 W @ 50 °C

-153 -153 -153 -153 -153 Page 3 of 5

Electrical Specifications, BASTA

Beamwidth, Horizontal ±2.9 ±1.7 ±2.6 ±2.6 ±4.3

Wind Speed, maximum 241 km/h | 149.75 mph

Packaging and Weights

Depth, packed 270 mm | 10.63 in

Length, packed 1955 mm | 76.969 in

Weight, gross 24 kg | 52.911 lb

You might also like