Rotary actuators

DA-H – series

HKS Unternehmensgruppe

Leipziger Straße 53-55

D-63607 Wächtersbach-Aufenau

Phone: +49 (0) 60 53 / 6163 - 0

Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2006 by HKS
 Technical informations DA-H 40
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 40
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 200
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 160
Because of the almost infinite design possibilities for Nominal torque Nm/bar 0,96
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 1567
Max. axial load N 8 000
Auxiliary equipment
Absorption volume Angle 90° dm3 0,020
- Cushioning at both ends
Angle 180° dm3 0,040
- Rotary angle adjustment up to + 4°
Angle 270° dm3 0,060
- Camshaft
Angle 360° dm3 0,080
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg approx 4,3
DIN 6885 profile
Angle 180° kg approx 4,8
Special versions Angle 270° kg approx 5,8
- Actuator shaft with spline profile to DIN Angle 360° kg approx 6,2
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 40 - 0606 E

armatures, as well as in shipbuilding, motor vehicles, Cushioning

assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2006 by HKS
Technical informations DA-H 40
Hydraulic rotary actuator

Standard version with feather key Dimension table

Typ DA-H 40
Ak6 22
DIN 5480*) W 22x1,25x16x8f
B Ø 98
Cf7 Ø 55
D 43
E Ø 65
F Ø 75
G 2,5
H DIN 6885 45
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885) I DIN 6885 8
J DIN 6885 14
K 84
L 50
M 3
N 4
O 16
P 90° 124
180° 149
270° 182
360° 210
Special version angle adjustment Special version threaded camshaft
Q 39
R 90° 28
180° 41
270° 55
360° 68,5
S 45° G 1/8"
T 60°
U Number 5
U 9
Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 26
Spline profile DIN 5463 6x11x14

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 45
J1 7,8
Special version with camshaft CH7 Ø 12
W f7 16 I1P9 4
W1 h6 10
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe N.B.: In the hollow shaft version it is
pivot
necessary to construct the shaft in a
Leipziger Straße 53-55 P1 90° 142 high strength material. A calculation
D-63607 Wächtersbach-Aufenau 180° 167 of the shaft for torsional strength is
270° 200 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 228
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2006 by HKS
 Technical informations DA-H 50
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 50
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 340
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 290
Because of the almost infinite design possibilities for Nominal torque Nm/bar 1,62
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 2976
Max. axial load N 10000
Auxiliary equipment
Absorption volume Angle 90° dm3 0,028
- Cushioning at both ends
Angle 180° dm3 0,056
- Rotary angle adjustment up to + 4°
Angle 270° dm3 0,084
- Camshaft
Angle 360° dm3 0,113
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 6
DIN 6885 profile
Angle 180° kg ca. 6,8
Special versions Angle 270° kg ca. 7,8
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 8,7
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 50 - 0606 E

armatures, as well as in shipbuilding, motor vehicles, Cushioning

assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2006 by HKS
Technical informations DA-H 50
Hydraulic rotary actuator

Standard version with feather key Dimension table

Typ DA-H 50
Ak6 28
DIN 5480*) W 28x2x12x8f
B Ø 110
Cf7 Ø 68
D 49
E Ø 72
F Ø 82
G 2
H DIN 6885 56
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885) I DIN 6885 8
J DIN 6885 17
K 90
L 60
M 3
N 4
O 18
P 90° 133
180° 164
270° 200
360° 232
Special version angle adjustment Special version threaded camshaft
Q 39
R 90° 31
180° 48
270° 65
360° 80,5
S 45° G 1/8"
T 60°
U Number 5
U 9
Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 30
Spline profile DIN 5463 6x16x20

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 55
J1 10,1
Special version with camshaft CH7 Ø 16
W f7 18 I1P9 5
W1 h6 10
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 149 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 182
the shaft for torsional strength is
270° 218 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 250
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2006 by HKS
 Technical informations DA-H 63
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 63
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 650
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 540
Because of the almost infinite design possibilities for Nominal torque Nm/bar 3,10
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 4364
Max. axial load N 14000
Auxiliary equipment
Absorption volume Angle 90° dm3 0,058
- Cushioning at both ends
Angle 180° dm3 0,117
- Rotary angle adjustment up to + 4°
Angle 270° dm3 0,176
- Camshaft
Angle 360° dm3 0,235
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 8,5
DIN 6885 profile
Angle 180° kg ca. 9,8
Special versions Angle 270° kg ca. 12,9
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 14
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 63 - 0606 E

armatures, as well as in shipbuilding, motor vehicles, Cushioning

assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2006 by HKS
Technical informations DA-H 63
Hydraulic rotary actuator

Standard version with feather key Dimension table

Typ DA-H 63
Ak6 35
DIN 5480*) W 35x2x16x8f
B Ø 128
Cf7 Ø 80
D 57
E Ø 87
F Ø 95
G 5
H DIN 6885 70
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885) I DIN 6885 10
J DIN 6885 20,5
K 108
L 80
M 3,5
N 5
O 25
P 90° 152
180° 200
270° 245
360° 284
Special version angle adjustment Special version threaded camshaft
Q 48
R 90° 37
180° 57
270° 79
360° 99
S 45° G 1/4"
T 60°
U Number 5
U 11
Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 35
Spline profile DIN 5463 6x21x25

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 65
J1 14,1
Special version with camshaft CH7 Ø 24
W f7 18 I1P9 8
W1 h6 10
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 172 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 220
the shaft for torsional strength is
270° 264,5 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 304,5
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2006 by HKS
 Technical informations DA-H 80
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 80
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 1300
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 1170
Because of the almost infinite design possibilities for Nominal torque Nm/bar 6,20
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 7875
Max. axial load N 19050
Auxiliary equipment
Absorption volume Angle 90° dm3 0,131
- Cushioning at both ends
Angle 180° dm3 0,262
- Rotary angle adjustment up to + 4°
Angle 270° dm3 0,391
- Camshaft
Angle 360° dm3 0,521
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 16,7
DIN 6885 profile
Angle 180° kg ca. 19,1
Special versions Angle 270° kg ca. 21,5
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 24
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 80 - 1208 E

armatures, as well as in shipbuilding, motor vehicles, Cushioning

assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 80
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 80
Ak6 42
DIN 5480*) W 40x2x18x8f
B Ø 150
Cf7 Ø 100
D 66
E Ø 108
F Ø 118
G 5
H DIN 6885 100
I DIN 6885 12
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 24
K 130
L 110
M 3
N 6
O 30
P 90° 187
180° 240
270° 290
360° 345
Special version angle adjustment Special version threaded camshaft
Q 57
R 90° 37
180° 74
270° 101
360° 125
S 45° G 3/8"
T 45°
U Number 7
U 11

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 40
Spline profile DIN 5463 6x26x32

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 90
J1 18,3
Special version with camshaft CH7 Ø 30
W f7 25 I1P9 8
W1 h6 16
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 212 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 262
the shaft for torsional strength is
270° 314,5 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 367,5
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 100
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 100
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 2500
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 2340
Because of the almost infinite design possibilities for Nominal torque Nm/bar 11,90
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 11250
Max. axial load N 24900
Auxiliary equipment
Absorption volume Angle 90° dm3 0,255
- Cushioning at both ends
Angle 180° dm3 0,509
- Rotary angle adjustment up to + 4°
Angle 270° dm3 0,763
- Camshaft
Angle 360° dm3 1,018
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca.24,1
DIN 6885 profile
Angle 180° kg ca.29,2
Special versions Angle 270° kg ca.34
- Actuator shaft with spline profile to DIN Angle 360° kg ca.38,5
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 100 - 1208 E

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles, Cushioning
assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 100
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 100
Am6 55
DIN 5480*) W 55x2x26x8f
B Ø 178
Cf7 Ø 115
D 80
E Ø 130
F Ø 147
G 5
H DIN 6885 100
I DIN 6885 16
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 31,5
K 155
L 110
M 4
N 6
O 31
P 90° 241
180° 311
270° 366
360° 432
Special version angle adjustment Special version threaded camshaft
Q 65
R 90° 56,5
180° 89
270° 121,5
360° 154
S 45° G 1/2"
T 45°
U Number 7
U 14

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 50
Spline profile DIN 5463 8x36x42

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 105
J1 24,3
Special version with camshaft CH7 Ø 42
W f7 25 I1P9 12
W1 h6 16
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 245 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 311
the shaft for torsional strength is
270° 381 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 442
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 125
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 125
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 5107
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 4900
Because of the almost infinite design possibilities for Nominal torque Nm/bar 24,32
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 17552
Max. axial load N 34100
Auxiliary equipment
Absorption volume Angle 90° dm3 0,518
- Cushioning at both ends
Angle 180° dm3 1,036
- Rotary angle adjustment up to + 4°
Angle 270° dm3 1,554
- Camshaft
Angle 360° dm3 2,071
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 47
DIN 6885 profile
Angle 180° kg ca. 55
Special versions Angle 270° kg ca. 63,5
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 72,5
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 125 - 1208 D

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles, Cushioning
assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 125
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 125
Am6 70
DIN 5480*) W 70x2x34x8f
B Ø 222
Cf7 Ø 150
D 94
E Ø 167
F Ø 183
G 7
H DIN 6885 125
I DIN 6885 20
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 39,5
K 195
L 140
M 4
N 8
O 37
P 90° 271,5
180° 392
270° 480
360° 532,5
Special version angle adjustment Special version threaded camshaft
Q 74
R 90° 76,2
180° 118,5
270° 162,5
360° 207
S 45° G 1/2"
T 40°
U Number 8
U 18

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 62
Spline profile DIN 5463 8x46x54

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 120
J1 31,8
Special version with camshaft CH7 Ø 55
W f7 25 I1P9 16
W1 h6 16
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 298 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 392
the shaft for torsional strength is
270° 482 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 557
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 140
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°, Technical data Type DA-H 140
270° and 360°
Max. nominal torque at 210 bars Nm 7100
- Actuator shaft with 2 feather keys or DIN
Max. nominal torque at 210 bars
5480 involute spline
- Tandem seal on the actuator shaft with camshaft Nm 6870
Nominal torque
Because of the almost infinite design possibilities for Nm/bar 33,80
Max. working pressure *
the front face almost all connection variants can be bar 210
achieved with these actuators. Max. radial load N 17800
Max. axial load N 34800
Auxiliary equipment Absorption volume Angle 90° dm3 0,759
- Cushioning at both ends Angle 180° dm3 1,518
- Rotary angle adjustment up to + 4° Angle 270° dm3 2,277
- Camshaft Angle 360° dm3 3,036
- Hollow shaft with DIN 5463, DIN 5480 or Weight Angle 90° kg ca. 74
DIN 6885 profile Angle 180° kg ca. 87
Special versions Angle 270° kg ca. 101
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 115
*) Working pressures > 210 bar on request
5463
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 140 - 1208 E

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles, Cushioning
assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 140
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 140
Am6 80
DIN 5480*) W 80x3x25x8f
B Ø 250
Cf7 Ø 160
D 105
E Ø 187
F Ø 210
G 5
H DIN 6885 140
I DIN 6885 22
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 45
K 220
L 150
M 7
N 10
O 40
P 90° 304
180° 401
270° 499
360° 597
Special version angle adjustment Special version threaded camshaft
Q 78
R 90° 82
180° 130
270° 180
360° 229
S 45° G 1/2"
T 40°
U Number 8
U 18

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 62
Spline profile DIN 5463 8x52x60

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 120
J1 34,4
Special version with camshaft CH7 Ø 60
W f7 25 I1P9 18
W1 h6 16
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 334,5 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 431
the shaft for torsional strength is
270° 529 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 627
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2006 by HKS
 Technical informations DA-H 160
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°, Technical data Type DA-H 160
270° and 360°
Max. nominal torque at 210 bars Nm 11300
- Actuator shaft with 2 feather keys or DIN
Max. nominal torque at 210 bars
5480 involute spline
- Tandem seal on the actuator shaft with camshaft Nm 10590
Nominal torque
Because of the almost infinite design possibilities for Nm/bar 53,80
Max. working pressure *
the front face almost all connection variants can be bar 210
achieved with these actuators. Max. radial load N 36300
Max. axial load N 46200
Auxiliary equipment Absorption volume Angle 90° dm3 1,145
- Cushioning at both ends Angle 180° dm3 2,290
- Rotary angle adjustment up to + 4° Angle 270° dm3 3,435
- Camshaft Angle 360° dm3 4,580
- Hollow shaft with DIN 5463, DIN 5480 or Weight Angle 90° kg ca. 114
DIN 6885 profile Angle 180° kg ca. 136
Special versions Angle 270° kg ca. 154
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 170
*) Working pressures > 210 bar on request
5463
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
The oil pressure supplied through connections P1 and P2 causes actuator
designed to customer’s requirements
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the here converted to a rotary movement by multiple helical gears in the housing,
range of rotation piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
Direction of rotation
positions
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 160 - 1208 E

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles, Cushioning
assembly platforms and in ventilation engineering.
The speed of rotation of actuator shaft G can be regulated in the limit
HKS rotary actuators are reliable and require no
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300 cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 160
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 160
Am6 100
DIN 5480*) W 100x3x32x8f
B Ø 278
Cf7 Ø 190
D 127
E Ø 206
F Ø 240
G 5
H DIN 6885 200
I DIN 6885 28
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 56
K 245
L 210
M 5
N 12
O 43
P 90° 364
180° 473,5
270° 592,5
360° 707,5
Special version angle adjustment Special version threaded camshaft
Q 94
R 90° 110
180° 168
270° 224
360° 281
S 45° G 3/4"
T 40°
U Number 8
U 22

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 82
Spline profile DIN 5463 8x62x72

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 150
J1 42,4
Special version with camshaft CH7 Ø 75
W f7 40 I1P9 20
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 394,5 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 502,5
the shaft for torsional strength is
270° 621,5 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 733,5
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 180
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°, Technical data Type DA-H 180
270° and 360°
- Actuator shaft with 2 feather keys or DINMax. nominal torque at 210 bars Nm 16200
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 15680
Nominal torque
Because of the almost infinite design possibilities for Nm/bar 77,14
Max. working pressure *
the front face almost all connection variants can be bar 210
achieved with these actuators. Max. radial load N 37600
Max. axial load N 47400
Auxiliary equipment Absorption volume Angle 90° dm3 1,678
- Cushioning at both ends Angle 180° dm3 3,356
- Rotary angle adjustment up to + 4° Angle 270° dm3 5,034
- Camshaft Angle 360° dm3 6,712
- Hollow shaft with DIN 5463, DIN 5480 or Weight Angle 90° kg ca. 150
DIN 6885 profile Angle 180° kg ca. 187
Special versions Angle 270° kg ca. 213
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 245
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
shaft G to perform a rotary movement. The linear movement of piston K is
- Rotary angle adjustment throughout the
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
Figure 1 shows the factory set position of piston K Changes of position are
- Further special versions are available
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 180 - 1208 E

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles, Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
positions by throttle check valves. Further information on the subject of
maintenance. This is demonstrated, for example, 2300
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 180
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 180
Am6 105
DIN 5480*) W 105x3x34x8f
B Ø 298
Cf7 Ø 210
D 138
E Ø 226
F Ø 270
G 5
H DIN 6885 200
I DIN 6885 28
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 58,5
K 265
L 210
M 5
N 12
O 47
P 90° 435
180° 565
270° 702
360° 880
Special version angle adjustment Special version threaded camshaft
Q 127
R 90° 114
180° 186
270° 253
360° 321
S 45° G 1"
T 40°
U Number 11
U 22

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 100
Spline profile DIN 5463 10x72x82

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 150
J1 42,4
Special version with camshaft CH7 Ø 75
W f7 32 I1P9 20
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 475 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 595
the shaft for torsional strength is
270° 742 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 900
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 200
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 200
270° and 360°
- Actuator shaft with 2 feather keys or DINMax. nominal torque at 210 bars Nm 22300
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 21400
Nominal torque
Because of the almost infinite design possibilities for Nm/bar 106,20
Max. working pressure *
the front face almost all connection variants can be bar 210
achieved with these actuators. Max. radial load N 67210
Max. axial load N 62000
Auxiliary equipment
Absorption volume Angle 90° dm3 2,261
- Cushioning at both ends
Angle 180° dm3 4,522
- Rotary angle adjustment up to + 4°
Angle 270° dm3 6,783
- Camshaft
Angle 360° dm3 9,044
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 194
DIN 6885 profile
Angle 180° kg ca. 238
Special versions Angle 270° kg ca. 264
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 306
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 200 - 1208 E

armatures, as well as in shipbuilding, motor vehicles,

Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 200
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 200
Am6 120
DIN 5480*) W 120x5x22x8f
B Ø 325
C f7 Ø 235
D 150
E Ø 255
F Ø 295
G 5
H DIN 6885 200
I DIN 6885 32
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 67
K 290
L 210
M 4
N 10
O 54
P 90° 438,5
180° 584,5
270° 725,5
360° 876,5
Special version angle adjustment Special version threaded camshaft
Q 125
R 90° 125
180° 196
270° 265,5
360° 340
S 45° G 1"
T 30°
U Number 11
U 22

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 100
Spline profile DIN 5463 10x82x92

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 175
J1 52,9
Special version with camshaft CH7 Ø 95
W f7 40 I1P9 25
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 478,5 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 632,5
the shaft for torsional strength is
270° 765,5 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 914,5
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 225
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 225
270° and 360°
- Actuator shaft with 2 feather keys or DINMax. nominal torque at 210 bars Nm 32000
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 30980
Nominal torque
Because of the almost infinite design possibilities for Nm/bar 152,38
Max. working pressure *
the front face almost all connection variants can be bar 210
achieved with these actuators. Max. radial load N 69000
Max. axial load N 63100
Auxiliary equipment
Absorption volume Angle 90° dm3 3,388
- Cushioning at both ends
Angle 180° dm3 6,676
- Rotary angle adjustment up to + 4°
Angle 270° dm3 10,014
- Camshaft
Angle 360° dm3 13,352
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Winkel 90° kg ca. 404
DIN 6885 profile
Angle 180° kg ca. 488
Special versions Angle 270° kg ca. 565
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 630
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 225 - 1208 E

armatures, as well as in shipbuilding, motor vehicles,

Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 225
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 225
Am6 140
DIN 5480*) W 120x5x26x8f
B Ø 385
C f7 Ø 260
D 224
E Ø 300
F Ø 350
G 5
H DIN 6885 250
I DIN 6885 36
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 78
K 345
L 260
M 6
N 15
O 64
P 90° 570
180° 732
270° 900
360° 1069
Special version angle adjustment Special version threaded camshaft
Q 155
R 90° 159
180° 240
270° 321
360° 403
S 45° G 1"
T 22,5°
U Number 15
U 22

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 120
Spline profile DIN 5463 10x92x102

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 175
J1 56,4
Special version with camshaft CH7 Ø 100
W f7 40 I1 P9 28
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 645 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 807
the shaft for torsional strength is
270° 975 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 1140
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 225 S
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 225 S
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 38920
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 37690
Because of the almost infinite design possibilities for Nominal torque Nm/bar 185,33
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 69000
Max. axial load N 63100
Auxiliary equipment
Absorption volume Angle 90° dm3 4,127
- Cushioning at both ends
Angle 180° dm3 8,245
- Rotary angle adjustment up to + 4°
Angle 270° dm3 12,368
- Camshaft
Angle 360° dm3 16,491
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 487
DIN 6885 profile
Angle 180° kg ca. 543
Special versions Angle 270° kg ca. 637
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 684
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
TI DA-H 225S - 1208 E

packing machines, transfer lines, manipulators,

armatures, as well as in shipbuilding, motor vehicles,
Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 225 S
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 225 S
Am6 140
DIN 5480*) W 140x5x26x8f
B Ø 385
Cf7 Ø 260
D 224
E Ø 300
F Ø 350
G 5
H DIN 6885 250
I DIN 6885 36
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 78
K 345
L 260
M 6
N 15
O 64
P 90° 690
180° 805
270° 995
360° 1220
Special version angle adjustment Special version threaded camshaft
Q 155
R 90° 175
180° 276
270° 381
360° 484
S 45° G 1"
T 22,5°
U Number 15
U 22

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 120
Spline profile DIN 5463 10x92x102

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 175
J1 56,4
Special version with camshaft CH7 Ø 100
W f7 40 I1P9 28
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 765 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 880
the shaft for torsional strength is
270° 1070 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 1295
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 250
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 250
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 44000
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 42870
Because of the almost infinite design possibilities for Nominal torque Nm/bar 209,52
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 78000
Max. axial load N 66500
Auxiliary equipment
Absorption volume Angle 90° dm3 4,607
- Cushioning at both ends
Angle 180° dm3 9,214
- Rotary angle adjustment up to + 4°
Angle 270° dm3 13,821
- Camshaft
Angle 360° dm3 18,429
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 630
DIN 6885 profile
Angle 180° kg ca. 726
Special versions Angle 270° kg ca. 815
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 912
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 250 - 1208 E

armatures, as well as in shipbuilding, motor vehicles,

Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 250
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 250
Am6 150
DIN 5480*) W 150x5x28x8f
B Ø 450
Cf7 Ø 300
D 240
E Ø 346
F Ø 385
G 10
H DIN 6885 280
I DIN 6885 36
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 83
K 400
L 300
M 6
N 20
O 90
P 90° 710
180° 875
270° 1060
360° 1261
Special version angle adjustment Special version threaded camshaft
Q 224
R 90° 155
180° 248
270° 343
360° 437
S 45° G 1"
T 22,5°
U Number 15
U 26

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 120
Spline profile DIN 5463 10x102x112

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 175
J1 61,4
Special version with camshaft CH7 Ø 110
W f7 40 I1P9 28
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 725 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 910
the shaft for torsional strength is
270° 1095 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 1286
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 280
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 280
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 60800
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 59580
Because of the almost infinite design possibilities for Nominal torque Nm/bar 289,52
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 84600
Max. axial load N 71000
Auxiliary equipment
Absorption volume Angle 90° dm3 6,348
- Cushioning at both ends
Angle 180° dm3 12,695
- Rotary angle adjustment up to + 4°
Angle 270° dm3 19,043
- Camshaft
Angle 360° dm3 25,391
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 874
DIN 6885 profile
Angle 180° kg ca. 1011
Special versions Angle 270° kg ca. 1164
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 1292
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 280 - 1208 E

armatures, as well as in shipbuilding, motor vehicles,

Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 280
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 280
Am6 170
DIN 5480*) W 170x5x32x8f
B Ø 490
Cf7 Ø 340
D 266
E Ø 394
F Ø 435
G 10
H DIN 6885 280
I DIN 6885 40
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 94
K 450
L 300
M 6
N 20
O 100
P 90° 790
180° 1000
270° 1205
360° 1408
Special version angle adjustment Special version threaded camshaft
Q 261
R 90° 183
180° 287
270° 392
360° 493
S 45° G 1"
T 18°
U Number 19
U 26

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 130
Spline profile DIN 5463 10x112x125

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 200
J1 67,4
Special version with camshaft CH7 Ø 120
W f7 40 I1P9 32
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 865 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 1075
the shaft for torsional strength is
270° 1280 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 1483
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 300
Hydraulic rotary actuator

General characteristics
Rotary actuators in the DA-H series are characterised
by their performance range. At a working pressure of
up to 210 bars, torques of up to 250,000 Nm are
possible (higher working pressures on request).
Another characteristic is the extremely low angular
clearance.

HKS rotary actuators in the DA-H series offer the

following standards:

- 20 sizes from 36 to 250000 Nm with pistons

Ø 40– Ø 450 mm Fig. 1
- 4 rotary angle rages for each size: 90°, 180°,
Technical data Type DA-H 300
270° and 360°
- Actuator shaft with 2 feather keys or DIN Max. nominal torque at 210 bars Nm 76000
5480 involute spline Max. nominal torque at 210 bars
- Tandem seal on the actuator shaft with camshaft Nm 74630
Because of the almost infinite design possibilities for Nominal torque Nm/bar 361,9
the front face almost all connection variants can be Max. working pressure * bar 210
achieved with these actuators. Max. radial load N 89400
Max. axial load N 76000
Auxiliary equipment
Absorption volume Angle 90° dm3 7,930
- Cushioning at both ends
Angle 180° dm3 15,862
- Rotary angle adjustment up to + 4°
Angle 270° dm3 23,790
- Camshaft
Angle 360° dm3 31,724
- Hollow shaft with DIN 5463, DIN 5480 or
Weight Angle 90° kg ca. 1126
DIN 6885 profile
Angle 180° kg ca. 1308
Special versions Angle 270° kg ca. 1489
- Actuator shaft with spline profile to DIN Angle 360° kg ca. 1677
5463 *) Working pressures > 210 bar on request
- Actuator shaft with second drive cog
Functional description
- Actuator shaft and mounting flange
designed to customer’s requirements The oil pressure supplied through connections P1 and P2 causes actuator
- Rotary angle adjustment throughout the shaft G to perform a rotary movement. The linear movement of piston K is
here converted to a rotary movement by multiple helical gears in the housing,
range of rotation
piston and shaft.
- Limit switch equipment
- Direct valve connection, 3 mounting
positions Direction of rotation
- All intermediate rotation angles can be With the pressure at P1 actuator shaft G1 rotates from the initial position to
supplied the left (anticlockwise).
- Range of rotation exceeding 360° A change in direction of rotation is possible in a special version.
- Sea-water resistant
- Additional bearing for high radial forces Normal position of the feather key:
- Change of direction of rotation
- Further special versions are available Figure 1 shows the factory set position of piston K Changes of position are
possible.
Typical applications

HKS rotary actuators have proved their worth Angle of rotation and its adjustment
throughout the industrial sector. For example, they In the standard version the angle of rotation may be up to 4° in the positive
are used in construction machinery, machine tools, range. An exact angle of rotation is achieved by means of an additional device
bending machines, foundry, mining, agricultural and WV.
packing machines, transfer lines, manipulators,
TI DA-H 300 - 1208 E

armatures, as well as in shipbuilding, motor vehicles,

Cushioning
assembly platforms and in ventilation engineering.
HKS rotary actuators are reliable and require no The speed of rotation of actuator shaft G can be regulated in the limit
maintenance. This is demonstrated, for example, 2300 positions by throttle check valves. Further information on the subject of
cushioning may be requested on an additional page.
mm below sea-level, whey they are used as actuators
for armatures. We reserve the right to make modifications Copyright © 2008 by HKS
 Technical informations DA-H 300
Hydraulic rotary actuator

Dimension table
Standard version with feather key
Typ DA-H 300
Am6 180
DIN 5480*) W 180x5x34x8f
B Ø 555
Cf7 Ø 380
D 285
E Ø 440
F Ø 470
G 10
H DIN 6885 280
I DIN 6885 45
Special version hollow shaft DIN 5463 Special version hollow shaft with feather key grooves (DIN 6885)
J DIN 6885 100
K 500
L 300
M 6
N 20
O 110
P 90° 840
180° 1060
270° 1285
360° 1510
Special version threaded camshaft
Special version angle adjustment
Q 271
R 90° 194
180° 302
270° 414
360° 528
S 45° G 1“
T 18°
U Number 19
U 32

Special version with female thread Special version camshaft with cog

Special version HW-hollow shaft to

DIN 5480 on request
B 140
Spline profile DIN 5472 130x145x24

Special version HWP - Hollow shaft

with key grooves (DIN 6885)
H1 200
J1 78,4
Special version with camshaft CH7 Ø 140
W f7 40 I1P9 36
W1 h6 25
Special version with angle *) Special version KW spline shaft
adjustment/camshaft/camshaft DIN is not shown
with tapped hole/camshaft with
HKS Unternehmensgruppe pivot N.B.: In the hollow shaft version it is
P1 90° 930 necessary to construct the shaft in a
Leipziger Straße 53-55 high strength material. A calculation of
D-63607 Wächtersbach-Aufenau 180° 1150
the shaft for torsional strength is
270° 1375 strongly recommended.
Phone: +49 (0) 60 53 / 6163 - 0 360° 1600
Extension Const. -11 / Sales. -21
Telefax: +49 (0) 60 53 / 6163 - 39

E-Mail: vertrieb@hks-partner.com
Internet: www.hks-partner.com We reserve the right to make modifications Copyright © 2008 by HKS