NSSCGrades Tipos INOX

Introduction to NSSC Series Stainless Steels
Head Office
3-2-2 Nihonbashi-Hongokucho, Chuo-ku, Tokyo, Japan 103-0021
Phone +81-3-3276-4800
Sales Offices
STAI N L E SS
Osaka Sales Office
Asahi-shinbun Bldg. 11F, 3-2-4 Nakanoshima, Kita-
Nagoya Sales Office
NS Bldg. 5F, 2-13-18 Meieki-minami, Nakamura-ku,
STE E L S
ku, Osaka-shi, Osaka-fu, Japan 530-0005 Nagoya-shi, Aichi Pref., Japan 450-0003
Phone 06 (4706) 1180 Phone 052 (581) 2012 Introduction
Kyushu Sales Office Chugoku Sales Office
to NSSC Series Stainless Steels
Hakata-NS Bldg. 4F, 5-18 Tenya-machi, Hakata-ku, Central Bldg. 7F, 15-10 Hacchobori, Naka-ku,
Fukuoka-shi, Fukuoka Pref., Japan 812-8522 Hiroshima-shi, Hiroshima Pref., Japan 730-0013
Phone 092 (273) 7090 Phone 082 (511) 5115
Niigata Sales Office

Mitsuibussan Bldg. 8F, 1-4-2 Higashi Oodori,
Niigata-shi, Niigata Pref., Japan 950-0087
Phone 025 (246) 3113
Works
Hikari Works Kashima Works Yawata Works

3434 Ooaza-shimada, Hikari- 2-1 Hikari, Kashima-shi, 2108-1 Aza-hato, Ooaza-maeda,
shi, Yamaguchi Pref., Japan Ibaraki Pref., Japan 314-0014 Yawatahigashi-ku, Kitakyushu-shi,
743-8550 Phone 0299 (84) 3702 Fukuoka Pref., Japan 805-0058
Phone 0833 (71) 5004 Phone 093 (672) 2356
For further information, please contact to the following department or nearest office
Technical Division
Nippon Steel & Sumikin Stainless Steel Corporation Head Office
Phone : +81-3-3276-4890
Facsimile : +81-3-3276-4928
Printed on recycled paper
"YUS" is a registered trademark of Nippon Steel Corpration (Registered Trademark Number:701414) , as is "NAR" of Sumitomo Metal Industries, Ltd. (Registered Trademark Number:2572515). Cat.No. SE001 2006.1① 2006.1 N
N SSC SE RI E S
Austenitic Stainless Steels
The austenitic type stainless steels, as far as worked with solid solution heat
treatment, are non-magnetic and nonhardenable by heat treatment, while they
exhibit a wide range of mechanical properties and become slightly magnetic when
cold worked.
And especially, they can exhibit the maximum softness, elongation and corrosion
resistance in its annealed state; that is, rapid cooling from high temperatures.
N SSC SE RI ES
Ferritic Stainless Steels
This stainless steel is Cr-type, and 18%-Cr stainless is most typical.
It cannot be hardened by heat treatment, while it shows the maximum softness,
elongation and corrosion resistance in its annealed state.
It offers magnetism as does the martensitic-type stainless steel.
N SSC SE RI ES
Martensitic Stainless Steels
This type of stainless steel can offer heat-treatment effects similar to those of most
alloy steels.
When subjected to appropriate heat treatment, it can also exhibit wide-ranging
mechanical properties. This type features strong magnetism.
N SSC SE RI ES
Austenitic-Ferritic (Duplex) Stainless Steels
With a duplex structure of austenite and ferrite, duplex type stainless steels show
excellence in corrosion resistance and strength.
NSSC Series
Content
2 ■ Guide to Selection of Appropriate Grade of NSSC Series Stainless Steels Ferritic Stainless Steels Martensitic Stainless Steels
4 ■ NSSC Series - Chemical Composition, Mechanical Properties and Other 21 ■ High-formability ferritic heat-resistant steel NSSC 409L 38 ■ High-strength, high stain-resistant ferritic NSSC 550
Key Information 22 ■ High-formability ferritic stainless steel NSSC 430D stainless steel
23 ■ High-formability ferritic stainless steel NSSC PDX
Austenitic Stainless Steels 24 ■ High stain-resistant ferritic stainless steel NSSC 160R
8 ■ High-formability austenitic stainless steel NSSC 27A, NSSC 27AM 25 ■ High stain-resistant ferritic stainless steel NSSC 432
39 ■ High-strength, high corrosion resistant duplex NSSC DX1
NSSC 27AS 26 ■ High stain-resistant ferritic stainless steel NSSC 436S
STAINLESS STEELS stainless steel
NSSC
9 ■ Deep-drawing austenitic stainless steel NSSC 304RM2 27 ■ High stain-resistant ferritic stainless steel NSSC 180
10 ■ Ultra-soft, high-formability austenitic stainless steel NSSC 304JS 28 ■ High corrosion resistant ferritic stainless steel NSSC 190
11 ■ Non-magnetic, high-strength austenitic stainless steel NSSC 130M 29 ■ High corrosion resistant ferritic stainless steel NSSC 190L 40 ■ Material Safety Data Sheet
12 ■ Non-magnetic austenitic stainless steel NSSC 131 30 ■ High stain-resistant ferritic stainless steel NSSC 220M
13 ■ High-strength austenitic stainless steel NSSC 304N 31 ■ Oxidation resistant ferritic stainless steel NSSC 405Si
14 ■ Ultra-low-carbon austenitic stainless steel NSSC 304UL, NSSC 316UL 32 ■ Heat resistant ferritic stainless steel NSSC FHZ
Important notice
S E R I E S
15 ■ Stress corrosion cracking resistant austenitic stainless NSSC 110M 33 ■ Heat resistant ferritic stainless steel NSSC 450MS
NSSC FH11 The technical information in this document simply describes typical
steel 34 ■ Heat resistant ferritic stainless steel
characteristics and performance of the product and does not provide any
16 ■ High-strength, pitting corrosion resistant austenitic NSSC 170 35 ■ Oxidation- and electric-resistant ferritic stainless steel NSSC HOM guarantees except for the items clearly stated as specifications or standard
values.
stainless steel 36 ■ High weldability ferritic stainless steel NSSC 410W
Note that NSSC takes no responsibility whatsoever for damage resulting
17 ■ High-strength, high corrosion resistant austenitic NSSC 317LN 37 ■ High weldability ferritic stainless steel NSSC 410WM from user failure to observe the instructions presented in this document or
improper handling of the product.
stainless steel The information presented in this document is subject to change without
18 ■ Sulfuric-acid resistant austenitic stainless steel NSSC 260, NSSC 260A notice. Please contact the relevant division for the latest information.
No part of this document may be copied or reproduced in any form without
19 ■ Seawater-corrosion resistant austenitic stainless steel NSSC 270, NSSC 270R the consent of NSSC.
20 ■ Heat-resistant austenitic stainless steel NSSC 305B
Introduction to NSSC Series Stainless Steels 1

Introduction to NSSC Series Stainless Steels
Welded portion
Weldability toughness
N SSC 410W N SSC 410 WM
Oxidation
Heat resistance, Formability resistance Oxidation resistance Oxidation resistance
TP 410 N SSC 409Ｌ N SSC 40 5Si NS SC F H1 1 NSS C HOM
STAINLESS STEELS
STAINLESS STEELS
N SSC F HZ N SSC 450 MS
High-temperature strength High-temperature
strength
Corrosion resistance
N SSC 550
Formability, Weldability Formability

TP 430 N SSC 430D N SSC P DX
Stain resistance
Corrosion
resistance Corrosion resistance Corrosion resistance
N SSC 180 N SSC 4 36S N SSC 190 NSSC 220M
Cold forging Mo reduction Welded portion toughness
N SSC 160R N SSC 43 2 NS SC 1 90L
N SSC 27AM
Stress corrosion
cracking resistance
Formability Formability
TP 304 N SSC 27A N SSC 27A S
(Sheet and strip)
Season cracking
resistance
Formability
N SSC 304ＲＭ 2 N SSC 30 4JS
Intergranular
corrosion
Intergranular corrosion resistance resistance
TP 304L N SSC 30 4U L
Corrosion
resistance Intergranular
corrosion
resistance
TP 316L N SSC 31 6U L
Intergranular
Corrosion corrosion Seawater-corrosion
resistance resistance Pitting corrosion resistance NS SC 2 60 resistance NSSC 270
Sulfuric-acid resistance
TP 316 N SSC 1 70
NS SC 2 60A N SSC 270 R
Stress corrosion cracking resistance
N SSC 110M
Non-magnetism,
High strength Non-magnetism High strength
N SSC 304N N SSC 13 1 NS SC 1 30M
Heat resistance Heat resistance

TP 310S N SSC 30 5B
Pitting-, or intergranular- corrosion resistance

TP 329 N SSC DX1
2 Introduction to NSSC Series Stainless Steels Introduction to NSSC Series Stainless Steels 3
NSSC Series - Chemical Composition, Mechanical Properties and Other Key Information
P：Plate
NSSC SERIES
C：Strip in coil
Austenitic Stainless Steels W：Wire rod
Chemical composition (mass %) Mechanical properties
Corresponding Product category
Symbol of grade Typical composition Characteristics Applications Yield strength Tensile Inside radius
specifications available C Si Mn P S Ni Cr Mo N Other significant 0.2% offset strength Elongation Hardness at bending
elements N/mm 2
N/mm 2 % angle of 180°
STAINLESS STEELS
STAINLESS STEELS
NSSC 27A Kitchen sink, 6.00 16.00
（YUS 27A） 17Cr-7Ni-2Cu High formability Door knob C ≦0.08 ≦2.00 ≦2.00 ≦0.040 ≦0.030 ーー Cu:1.50 2.50 ≧205 ≧520 ≧40 Hv≦200 ー
8.00 18.00
NSSC 27AM High formability, Hot-water tank,
Stress corrosion 1.00 6.00 16.00
SUS 304J1 17Cr-7Ni-2Cu-1.5Si Dish washer C ≦0.08 ≦2.00 ≦0.040 ≦0.030 ーー Cu:1.50 2.50 ≧205 ≧520 ≧40 Hv≦200 ー
（YUS 27A-M） cracking resistance 2.00 8.00 18.00
Formability
High formability, Design oriented 6.00 15.00

NSSC 27AS 17Cr-7Ni-2Cu-LC,N C ≦0.05 ≦2.00 ≦2.00 ≦0.040 ≦0.030 ー ≦0.03 Cu:1.50 2.50 ≧155 ≧450 ≧40 Hv≦200 ー
Softness kitchen sink 8.00 18.00
NSSC 304RM2 High formability, Kitchen sink, 9.00 18.00

ー 18Cr-9Ni-1Cu Season cracking C ≦0.08 ≦1.00 ≦2.00 ≦0.045 ≦0.030 ーー Cu:0.5 1.5 ≧205 ≧540 ≧50 Hv≦188 ー
（NAR-304RM2） Beer barrel, Coin 10.00 20.00
resistance
1.50 ≦0.040 ≦0.030 7.00 16.00
SUS 304J1 High formability, Softness, Precision press
NSSC 304JS 17Cr-8Ni-3Mn-3Cu-LC,N Season cracking resistance C ≦0.03 ≦1.00 ー ≦0.03 Cu:2.00 4.00 ≧155 ≧450 ≧40 Hv≦200 ー
SUS 304J2 equipment 3.50 9.00 18.00
NSSC 130M High strength, Guide pin, 0.07 9.0 5.00 17.00 0.20
ー 18Cr-6Ni-9Mn-0.3N W ≦1.00 ≦0.030 ≦0.030 ーーーーーーー
（YUS 130M） Non-magnetism Non-magnetic bolt 0.12 10.0 6.00 19.00 0.35
High strength
NSSC 131 Non-magnetic 0.01 3.00 5.00 17.00 0.10

（YUS 131）ー 18Cr-6Ni-5Mn-0.2N Non-magnetism apparel parts, Spoke W ≦1.00 ≦0.040 ≦0.030 ーーーーーーー
0.05 7.00 6.00 19.00 0.30
NSSC 304N SUS 304N2 High-pressure equipment, 7.50 18.00 Hv≦260

18Cr-8Ni-0.2N-Nb High strength P, C ≦0.08 ≦1.00 ≦2.50 ≦0.040 ≦0.030 ー ≦0.25 Nb≦0.14 ≧345 ≧690 ≧40 ー
（YUS 304N） ASTM XM-21 Centrifugal separator 10.50 20.00 HBW≦250
NSSC 304UL Intergranular corrosion Spent nuclear fuel 9.00 18.00

SUS 304L 18Cr-10Ni-LC P ≦0.020 ≦1.00 ≦2.00 ≦0.040 ≦0.030 ーーー ≧175 ≧480 ≧40 HBW≦187 ー
（YUS 304UL） resistance reprocessing equipment 13.00 20.00
NSSC 316UL Intergranular corrosion Spent nuclear fuel 12.00 16.00 2.00
SUS 316L 17Cr-15Ni-2Mo-LC P ≦0.020 ≦1.00 ≦2.00 ≦0.040 ≦0.030 ーー ≧175 ≧480 ≧40 HBW≦187 ー
（YUS 316UL） resistance reprocessing equipment 16.00 18.00 3.00
NSSC 316C Corrosion resistance, Machine screw, 10.00 16.00 2.00

SUS 316J1 18Cr-12Ni-2Mo-Cu W ≦0.08 ≦1.00 ≦2.00 ≦0.045 ≦0.030 ー Cu:2.00 4.00 ーーーーー
（YUS 316C） Formability Nut and bolt 14.00 18.00 3.00
NSSC 110M Stress corrosion Hot-water-supply system, 1.50 9.50 17.50 0.50
C
High corrosion-resistance
SUS 315J1 18Cr-10Ni-2Cu-2Si-0.8Mo Home appliance, ≦0.08 ≦1.00 ≦0.030 ≦0.030 ー Cu:1.50 2.50 ≧205 ≧520 ≧40 Hv≦200 ー
（YUS 110M） cracking resistance 2.50 11.50 19.50 1.00
Heat exchanger
NSSC 170 Pitting corrosion resistance, Exhaust gas desulfurizer, 12.00 23.00 0.50 0.25 Hv≦260
SUS 317J2 25Cr-13Ni-0.9Mo-0.3N P,（C）, W ≦0.06 ≦1.50 ≦2.00 ≦0.040 ≦0.030 ー ≧345 ≧690 ≧40 ー
（YUS 170） High strength High temperature usage 16.00 26.00 1.20 0.40 HBW≦250
NSSC 317LN Pitting corrosion resistance, Chemical plant, 11.00 18.00 3.00 0.10
SUS 317LN 19Cr-13Ni-3.5Mo-0.2N-LC P, C ≦0.030 ≦1.00 ≦2.00 ≦0.045 ≦0.030 ー ≧245 ≧550 ≧40 HBW≦217 ー
（YUS 317LN） High strength Chemical tank 15.00 20.00 4.00 0.22
NSSC 260 20Cr-15Ni-3Mo-1.5Cu- Oxidation resistance, Chimney, 13.50 18.50 2.50 0.16
ー P ≦0.030 ≦1.50 ≦2.00 ≦0.040 ≦0.030 Cu:1.00 2.00 ≧275 ≧550 ≧35 HBW≦217 ー
（YUS 260） 0.2N-LC High strength Sulfuric acid plant 16.50 21.50 3.50 0.24
22Cr-16Ni-3.5Mo-2Cu- Oxidation resistance, 20.00 3.00 0.10

NSSC 260A ー Chemical tanker P ≦0.030 ≦1.00 ≦2.00 ≦0.040 ≦0.030 13.00 Cu:1.50 3.00 ≧315 ≧600 ≧35 HBW≦230 ー
0.2N-LC High strength 17.00 23.00 4.00 0.22
NSSC 270 SUS 312L Seawater-corrosion Seawater desalination plant, 17.00 19.00 5.50 0.16 Hv≦230
20Cr-18Ni-6Mo-0.2N-LC resistance, P, C ≦0.020 ≦0.80 ≦1.00 ≦0.030 ≦0.015 Cu:0.50 1.00 ≧300 ≧650 ≧35 ー
（YUS 270） ASTM S31254 High strength Building exterior material 19.50 21.00 6.50 0.24 HBW≦220
NSSC 270R Seawater-corrosion Corrosion resistant screw, 22.00 19.00 5.50

ー 20Cr-23Ni-6Mo-LN W ≦0.020 ≦0.80 ≦1.00 ≦0.030 ≦0.015 ≦0.05 Cu:0.50 1.00 ーーーーー
（YUS 270R） resistance nut and bolt, Wire netting 23.50 21.00 6.50
High heat-
resistance
Automotive exhaust 3.00 17.50

NSSC 305B SUS XM15J1
19Cr-13Ni-3.5Si
Heat resistance,
C ≦0.08 ≦1.00 ≦0.030 ≦0.030 12.00 ーーー ≧205 ≧540 ≧45 Hv≦200 ー
（NAR-305B） ASTM XM-15 Oxidation resistance system, Burner 4.00 15.00 20.00
NSSC Series - Chemical Composition, Mechanical Properties and Other Key Information
P：Plate
NSSC SERIES
C：Strip in coil
Ferritic Stainless Steels W：Wire rod
Chemical composition (mass %) Mechanical properties
Corresponding Product category
Symbol of grade Typical composition Characteristics Applications Yield strength Tensile Inside radius
specifications available C Si Mn P S Ni Cr Mo N Other significant 0.2% offset strength Elongation Hardness at bending
elements N/mm 2
N/mm 2 % angle of 180°
STAINLESS STEELS
STAINLESS STEELS
NSSC 409L SUH 409L 11Cr-0.2Ti-LC Automotive exhaust system, C, P ≦0.030 ≦1.00 ≦1.00 ≦0.040 ≦0.030 10.50 ≦0.015 Ti:10（C＋N） ≧175
ーー ≧360 ≧25 Hv≦180 1.0t
Formability
High formability
（YUS 409D,NAR-409L） Heat exchanger 11.75 0.75
NSSC 430D SUS 430LX Kitchen furnishings, 16.00 Ti≧0.10 and
（YUS 430D） ASTM 439 17Cr-0.4Ti-LC,N High formability C ≦0.030 ≦0.50 ≦1.00 ≦0.040 ≦0.030 ーーー Ti≧16（C＋N） ≧175 ≧360 ≧28 Hv≦180 1.0t
Gas burner 18.00
NSSC PDX SUS 430LX High formability, Combustion component, 16.00 Ti:8（C＋N）
（YUS PDX） ASTM 439 17Cr-0.2Ti-ULC,N Softness Front door of refrigerator C ≦0.010 ≦0.50 ≦1.00 ≦0.030 ≦0.030 ーーー ≧175 ≧360 ≧30 Hv≦180 1.0t
18.00 0.30
16.00
NSSC 160R ー 17Cr-0.4Cu-Nb-LC,N Cold forging Wire netting, Screw W ≦0.02 ≦1.00 ≦1.00 ≦0.040 ≦0.006 ー 18.00 ー ≦0.02 Nb:0.30 0.60 ーーーーー
Automotive muffler,
0.45
NSSC 432 ≦0.015 Ti:10（C＋N）
Corrosion resistance, 17.00
17Cr-0.5Mo-0.2Ti-LC,N Kitchen furnishings, C ≦0.010 ≦0.14 ≦0.20 ≦0.035 ≦0.006 ー ≧205 ≧390 ≧25 Hv≦170 1.0t
（YUS 432,NAR-436J1L） SUS 436J1L High formability Home appliance 18.00 0.65 0.30
High corrosion-resistance
NSSC 436S SUS 436L Corrosion resistance, Automotive muffler, 17.00 1.00 Ti:10（C＋N）
17Cr-1.2Mo-0.2Ti-LSi-LC,N C, P ≦0.010 ≦0.14 ≦0.20 ≦0.040 ≦0.006 ー ≦0.015 ≧205 ≧390 ≧25 Hv≦170 1.0t
（YUS 436S,NAR-436S） ASTM 436 High formability Structural member 18.00 1.50 0.35
NSSC 180 Cu:0.30 0.60
SUS 430J1L 19Cr-0.4Cu-0.4Nb-LC,N Stain resistance Automotive trim material, C, W ≦0.02 ≦1.00 ≦1.00 ≦0.040 ≦0.006 ≦0.60 19.00 ー ≦0.025 Nb≧10（C＋N） ≧205 ≧450 ≧22 Hv≦200 1.0t
（YUS 180） Kitchen furnishings 21.00 and 0.30 0.80
NSSC 190 Hot-water boiler, 1.75
19Cr-2Mo-Nb,Ti-LC,N Pitting corrosion Water tank, C, W 18.00 （Ti＋Nb）≧
（YUS 190） resistance ≦0.015 ≦0.50 ≦0.50 ≦0.040 ≦0.030 ー 20.00 2.25 ≦0.015 16（C＋N） ≧205 ≧450 ≧22 Hv≦200 t＜8mm:0.5t
Solar-heat collector
SUS 444
NSSC 190L Pitting corrosion resistance, Petro-chemical equipment, P,（C） 18.00 1.75 Nb≧8（C＋N） Hv≦230 t＜8mm:0.5t
（YUS 190L） 19Cr-2Mo-Nb-V-LC,N Weldability Heat exchanger, Storage tank ≦0.015 ≦0.50 ≦0.50 ≦0.040 ≦0.030 ー 20.00 2.25 ≦0.015 V≦0.20 ≧245 ≧410 ≧22 HBW≦217 t≧8mm:1.0t
NSSC 220M
（YUS 220M）
SUS 445J2 22Cr-1.5Mo-Nb,Ti-LC,N High stain-resistance Roofing, Siding C ≦0.010 ≦1.00 ≦1.00 ≦0.040 ≦0.007 ≦0.60 22.00 1.50 ≦0.020 （Ti＋Nb）≧ ≧295 ≧470 ≧22 Hv≦200 1.0t
23.00 2.50 16（C＋N）
NSSC 405Si ー 12Cr-2Si-0.15AI Oxidation resistance Heater, Burner, C ≦0.080 1.00 ≦1.00 ≦0.040 ≦0.030 ー 11.50
ーー AI:0.10 0.30 ≧295 ≧490 ≧15 Hv≦230 2.0t
Gas burner 3.00 14.50
0.80 0.20 13.00
High heat-resistance
NSSC FHZ ー 13Cr-1Si-Nb-LC High-temperature Automotive exhaust system, ≦0.020

1.20 ≦0.040 ≦0.010
C ーー ≦0.025 Nb:0.40 0.80 ≧205 ≧410 ≧25 Hv≦200 1.0t
（NAR-FH-Z） strength Exhaust gas boiler duct 1.40 15.00
NSSC 450MS High-temperature Automotive exhaust system 13.50 0.40 Ti:0.10 0.30
ー 14Cr-0.5Mo-0.3Nb-0.1Ti-LC C ≦0.015 ≦2.00 ≦2.00 ≦0.040 ≦0.030 ー 14.50 1.00 ≦0.015 Nb:0.20 0.50 ≧205 ≧390 ≧25 Hv≦200 1.0t
（YUS 450 MS） strength (incl. exhaust manifold)
NSSC FH11 Heater, Burner, 2.40 17.50
ー 18Cr-2.5Si-Nb-LC Oxidation resistance C ≦0.030
2.80 ≦1.00 ≦0.040 ≦0.030 ーーー Nb:0.20 0.50 ≧205 ≧410 ≧22 Hv≦230 1.0t
（NAR-FH-11） Gas burner 18.50
17.00 Ti:0.10 0.50
NSSC 21M SUH 21 18Cr-2Al-Ti Oxidation resistance Motorcycle muffler C ≦0.030 ≦1.00 ≦1.00 ≦0.040 ≦0.030 ー
19.00 ーー Al:1.50 2.50 ≧205 ≧410 ≧15 Hv≦230 ー
NSSC HOM Oxidation resistance, Electric-resistant 14.00
ー 15Cr-4Al-LC,N C ≦0.015 ≦1.00 ≦1.00 ≦0.040 ≦0.030 ーーー Al:3.00 5.00 ≧350 ≧520 ≧15 Hv≦230 ー
（HOM 125） Electric resistance /heat-resistant apparatus 16.00
NSSC 410W Heat-resistant 11.50
Weldability
（YUS 410W） SUS 410L 12Cr-LC Weldability apparatus P, C, W ≦0.030 ≦1.00 ≦1.00 ≦0.040 ≦0.030 ー 13.50 ーーー ≧195 ≧360 ≧22 Hv≦200 1.0t
NSSC 410WM Weldability, Marine container 10.75
SUS 410L 11Cr-Ni-LC,N P, C ≦0.030 ≦0.50 ≦1.00 ≦0.035 ≦0.025 ≦0.50 12.00 ー ≦0.025 ー ≧315 ≧430 ≧20 Hv≦240 t≦5mm:1.0t
（YUS 410W-MS） Weld zone toughness frame material （t≦5mm）
NSSC SERIES
Martensitic Stainless Steels
strength
NSSC 410DA ー 12Cr-0.07C High hardness Disc brake C Trace 11.50

≦0.08 ≦0.50 ≦1.00 ≦0.040 ≦0.010 amount ーー ≧205 ≧410 ≧20 Hv≦200 ー
ー
High
13.50
NSSC 550 High hardness, Self-tapping screw, 0.10 1.00 12.50 1.80 0.05
（YUS 550）ー 13Cr-2Ni-2Mo High stain-resistance Nail of high-strength W 0.20 ≦1.00 ≦1.00 ≦0.040 ≦0.010 2.40 14.00 2.30 0.15 ーーーーーー
NSSC SERIES
corrosion-
resistance
NSSC DX1 SUS 329J3L High strength, Pitting-corrosion Chemical plant, 4.50 21.00 2.50 0.08
22Cr-5Ni-3Mo-LC-0.13N P ≦0.03 ≦1.00 ≦2.00 ≦0.030 ≦0.020 3.50 ー ≧450 ≧620 ≧25 HBW≦290 ー
（YUS-DX1） 6.50 23.00 0.20
High
DIN 1.4462 /intergranular-corrosion resistance Energy-related plat
NSSC SERIES NSSC SERIES
AUSTENITIC High-formability austenitic stainless steel AUSTENITIC

Deep-drawing austenitic stainless steel
NSSC 27A, NSSC 27AM,
27AM, NSSC 27AS NSSC 304RM2
17Cr-7Ni-2Cu-（1.5Si）（
- LC,N）／Corresponding specification:SUS 304J1 18Cr-9Ni-1Cu
■Features
Features and Applications ■Features
Features and Applications
STAINLESS STEELS
STAINLESS STEELS
NSSC 27A: Superior to SUS304 in deep drawability and strechability Superior to SUS 304 in formability and season cracking resistance
NSSC 27AM: High performance in stress corrosion cracking resistance, exceeding that of NSSC 27A 1. Superior to SUS 304 in press working as deep-drawing
NSSC 27AS: High performance in formability, a feature drawn out by softening process of NSSC 27A 2. Superior to SUS 304 in season cracking resistance
［Typical Applications］ Kitchen sink, door knob（NSSC 27A）［Typical Applications］ Kitchen sink both for domestic and business use, beer barrel, coin for game machine
［Typical Applications］ Hot-water tank, dish washer（NSSC 27AM）
［Typical Applications］ Design oriented kitchen sink（NSSC 27AS）
■Chemical
Chemical composition（mass
mass %
%）
■Chemical
mass %
%） C Si Mn P S Ni Cr Cu
AUSTENITIC
AUSTENITIC
C Si Mn P S Ni Cr Cu 9.00 18.00 0.5

Specification ≦0.08 ≦1.00 ≦2.00 ≦0.045 ≦0.030
NSSC 27A and 27AM Specification ≦0.08 ≦2.00 ≦2.00 ≦0.040 ≦0.030 6.00 8.00 16.00 18.00 1.50 2.50 10.00 20.00 1.5
NSSC 27A Typical type 0.05 0.44 1.00 0.028 0.001 6.50 17.36 2.25 Typical type 0.05 0.41 0.91 0.031 0.002 9.11 18.22 1.0
NSSC 27AM Typical type 0.04 1.50 1.06 0.026 0.001 6.84 16.87 2.23
NSSC 27AS Specification ≦0.05 ≦2.00 ≦2.00 ≦0.040 ≦0.030 6.00 8.00 15.00 18.00 1.50 2.50
■Characteristics
Characteristics
NSSC 27AS Typical type 0.02 0.43 1.15 0.028 0.001 7.78 16.64 1.83
NSSC 27A,AM
NSSC 304RM2
［Mechanical properties］
NSSC 27AS
Yield strength 0.2% offset Tensile strength Elongation Hardness

■Characteristics
Characteristics N/mm2 N/mm2 % Hv
［Mechanical properties］［Stress corrosion cracking resistance］ Specification ≧205 ≧540 ≧50 ≦188
Yield strength Tensile Erichsen Immersed in 42％MgCl 2 solution, at boiling point Typical type
0.2% offset strength
Elongation Hardness 272 594 57 150
value 8
N/mm2 N/mm2 % Hv mm
NSSC 27A and 27AM ：Applied stress15kgf/mm2
≧205 ≧520 ≧40 ≦200 ー
Rupture time （hr）
Specification 7 ：Applied stress20kgf/mm2 ［Season cracking resistance］

NSSC 27A Typical type 257 629 56 146 14.4 6
NSSC 27AM Typical type 281 657 60 163 14.0 5
Grade NSSC 304RM2 SUS 304
SUS 304
NSSC 27AS Specification ≧155 ≧450 ≧40 ≦200 ー 4
NSSC 27AS Typical type 238 550 52 159 14.2 Result of test No cracking Cracking within 24 hours
3
SUS 304 Typical type 298 668 52 159 11.8 NSSC 27AM
2 Thickness of test specimens: 1.5mm Drawing ratio: 2.25 Cracking
［Drawability］ Immersed in hot water of 80℃ for 360 hours, after cup drawing
1 NSSC 27A
Drawing ratio 0
2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 50 52 54 56 58 60
45 Elongation （%）
〈Press conditions〉
Thickness：0.4mm
Drawable depth（mm）
Punch： 4 0 ×4 R p
40 Dies： 4 2 ×4 R d
Lubricant： JW♯122
35 Blank holding ［Stress corrosion cracking resistance at welded portion］
force ：1ton
（Test conditions）
30 NSSC 27A Immersed in42％MgCl2 solution, at boiling point, 4hours, NSSC 304RM2 SUS 304
NSSC 27AM Test specimens : ring bead of TIG welding without filler
25
NSSC 27A NSSC 27AM SUS 304
20
SUS 304
15
10
78 80 82 84 86 88 90 92 94 96 98
Blank diameter（mm）
AUSTENITIC Ultra-soft, high-formability austenitic stainless steel AUSTENITIC Non-magnetic, high-strength austenitic stainless steel
NSSC 304JS NSSC 130M
17Cr-8Ni-3Mn-3Cu-LC,N／Corresponding grade：SUS 304J1,J2 18Cr-6Ni-9Mn-0.3N
■Features
STAINLESS STEELS
STAINLESS STEELS
A brand-new grade of austenitic stainless steel of ultra-softness（as well as of reduced yield strength and of 1. can obtain hardness of 500Hv and over through cold working
restrained work hardening） 2. Non-magneticsm and low permeability of less than 1.01 even after tough working
1. High performance in secondary work after multistage drawings or press work with only a minimal spring back followed 3. Equal level of corrosion resistance to seawater as SUS 304
2. High level of season cracking resistance 4. Proof against cold working of 70% or more
3. Extremely smaller magnetism than SUS 304 after formation
4. The line-up includes a pre-coated, high lubrication sheet of oil-free ［Typical Applications］ Guide pins, non-magnetic bolts, non-magnetic apparel parts
■Chemical
mass %
%） ■Chemical
mass %
%）
C Si Mn P S Ni Cr Cu N C Si Mn P S Ni Cr N
AUSTENITIC
AUSTENITIC
Specification ≦0.03 ≦1.00 1.50 3.50 ≦0.040 ≦0.030 7.00 9.00 16.00 18.00 2.00 4.00 ≦0.03 Specification 0.07 0.12 ≦1.00 9.0 10.0 ≦0.030 ≦0.030 5.00 6.00 17.00 19.00 0.20 0.35
Typical type 0.01 0.46 2.67 0.032 0.002 8.02 17.42 2.71 0.01 Typical type 0.09 0.47 9.43 0.027 0.005 5.61 18.18 0.30
■Characteristics
Characteristics ■Characteristics
Characteristics
［Mechanical properties］［Mechanical properties］- after solution heat treatment -
Yield strength Tensile Elongation Hardness Pressure buldge Yield strength
0.2% offset n value Tensile strength Elongation
NSSC 304JS
strength height
NSSC 130M
0.2% offset
N/mm2 N/mm2 ％ Hv mm N/mm2 N/mm2 %
Specification ≧155 ≧450 ≧40 ≦200 ーー Typical type 500 850 42.5
Typical type 201 492 59 109 0.39 42.2
SUS 304 Typical type 274 680 59 170 0.49 40.3
［Work hardening characteristics］
（Surface finish: No. 2D, Thickness: 1.5mm） -relationship between reduction of area by wire drawing and mechanical properties -
■Formability
Formability
［Cup drawing formability ］［Multistage cup drawing formability］ 2000 600
（N/mm2）
Thickness：1.5mm Thickness：0.8mm Lubricant：Johnson-Wax #122 1800 Tensile strength
Blank diameter：90mmφ, Punch diameter：50mmφ Initial blank diameter：96mmφ 1600 500
Drawing depth：25mm Punch diameter：48mmφ （1st stage）-22mmφ
（7th stage）
Hardness（Hv ）
1400
1200 60 400
Tensile strength
18 SUS 304 exhibited
1000 50 Hardness
a season cracking
（％）
16 at the 3rd stage 800 40 300
drawing. 600
Elongation
30
14
400 20 200
Elongation
12 200 10
Press load（ton）
0 0 100
10 20 40 60 80
Reduction of area by wire drawing（％）
8
6 ［Permeability］- after wire drawing -

NSSC 304JS SUS 304
4 Seven-stage drawings Two-stage drawings
（drawing ratio: 4.4）（drawing ratio: 2.2）
2 2.00
［Shape - fixability in hat bending］ SUS 304
Permeability
0 Thickness：0.8mm Forming height：70mm Blank holding force：5ton
Pre-coating Lubricant Lubricant 1.40
lubricant film oil oil
NSSC 304JS SUS 304 1.01 NSSC 130M

SUS 304
20 40 60 80
NSSC 304JS
（NSSC 304JS exhibits only a minimal spring back after press.）
AUSTENITIC Non-magnetic austenitic stainless steel AUSTENITIC High-strength austenitic stainless steel
NSSC 131 NSSC 304N
18Cr-6Ni-5Mn-0.2N 18Cr-8Ni-0.2N-Nb／Corresponding grade:SUS 304N2
■Features
STAINLESS STEELS
STAINLESS STEELS
1. Non-magnetism even after tough working（permeability≦1.02） Nitrogen-added grade which exhibits much higher strength（yield strength 0.2% offset is particularly high）and
2. Equal level of corrosion resistance to seawater as SUS 304 provides with advantages over SUS 304 in potential of structural designs
3. Proof against cold working of 80% or more 1. Remarkably higher strength at room to elevated temperatures and fatigue strength than those of SUS 304
2. Equal level of corrosion resistance, heat resistance and physical properties as SUS 304
［Typical Applications］ Non-magnetic apparel parts, Non-magnetic nail, Spoke 3. High performance of weldability, and especially of the welded joint, with use of welding materials of similar
composition
［Typical Applications］ High-pressure equipment, Centrifugal separator, equipment employing SUS 304
■Chemical
mass %
%）
C Si Mn P S Ni Cr N
■Chemical
AUSTENITIC
AUSTENITIC
mass %
%）
Specification 0.01 0.05 ≦1.00 3.00 7.00 ≦0.040 ≦0.030 5.00 6.00 17.00 19.00 0.10 0.30
Typical type 0.03 0.42 5.21 0.027 0.001 5.61 17.90 0.16 C Si Mn P S Ni Cr Nb N
Specification ≦0.08 ≦1.00 ≦2.50 ≦0.040 ≦0.030 7.50 10.50 18.00 20.00 ≦0.14 ≦0.25
■Characteristics
Characteristics Typical type 0.05 0.71 0.84 0.028 0.001 7.73 19.06 0.11 0.17
［Mechanical properties］- after solution heat treatment -
NSSC 304N
NSSC 131
Yield strength
0.2% offset Tensile strength Elongation
N/mm2 N/mm2 % ■Characteristics
Characteristics
Typical type 600 780 26 ［Mechanical properties］
Yield strength Tensile Elongation
strength Hardness
0.2% offset
［Work hardening characteristics］ N/mm2 N/mm2 % HBW
-relationship between reduction of area by wire drawing and mechanical properties-
Specification ≧345 ≧690 ≧40 ≦250
NSSC 304N
Tensile strength（N/mm2）
2000 30 Typical type 481 814 49 170

Tensile strength
（％）
25 Specification ≧205 ≧520 ≧40 ≦187

1500 SUS 304
20 Typical type 255 579 63 126
Elongation
1000 15
10
500 Elongation ［High-temperature strength］［Corrosion resistance］
5
Test conditions NSSC 304N SUS
304
Yield strength 0.2% offset（N/mm 2 ）, Tensile strength（N/mm 2 ）

0 0 Solution Temperature Period Base metal Welded portion Base metal
0 20 40 60 80 100 g/m2/hr g/m2/hr g/m2/hr
composition ℃ hr
Reduction of area by wire drawing（％） 800
Reduction acid 2% H2SO4 Boil 6 184.8 172.4 206.0
Reduction acid 1% HCI ″ ″ 83.5 57.9 25.0
NSSC 304N
［Permeability］- after wire drawing - Reduction acid 10% HCI 25 24 1.60 1.70 0.81
600
Oxidizing acid 65% HNO3 Boil 48 0.22 0.26 0.15
1.2 （5cycle）
SUS 304 20% 6 0.03 0.05 0.17
Organic acid ″
Yield strength Tensile strength

CH3COOH
0.5M
400 Pitting corrosion FeCI3
25 48 4.75 8.08 9.80
Permeability
（Test specimens：2mm×30mm×30mm）
1.1 NSSC 304N
200
1.0
0 SUS 304
20 40 60 80 100
0 200 400 600
Temperature（℃）
AUSTENITIC Ultra-low-carbon austenitic stainless steel AUSTENITIC Stress corrosion cracking resistant austenitic stainless steel
ＮＳＳＣ 304UL, ＮＳＳＣ 316UL NSSC 110M
18Cr-10Ni-LC, 17Cr-15Ni-2Mo-LC／Corresponding grade : SUS 316L 18Cr-10Ni-2Cu-2Si-0.8Mo／Corresponding grade : SUS 315J1
■Features
STAINLESS STEELS
STAINLESS STEELS
Superior to SUS 304 and SUS 316L in intergranular corrosion resistance Exquisite performance of stress corrosion cracking resistance against neutral chlorides
Secured safety against intergranular corrosion realized with ultra-low carbon content（C≦0.020% ） 1 High performance in pitting corrosion resistance and chink corrosion resistance, in addition to stress
corrosion cracking resistance
［Typical Applications］ Spent nuclear fuel reprocessing equipment, Various equipments susceptible to intergranular
2. Equal level of formability as SUS 316
［Typical Applications］ corrosion
3. Superior to SUS 316 in oxidation resistance
■Chemical
mass %
%）［Typical Applications］ Hot-water related equipment as hot-water-supply system or heat exchanger,
［Typical Applications］ Flexible pipe or other components of automotive exhaust system, Any other corrosion-
C Si Mn P S Ni Cr Mo ［Typical Applications］ sensitive equipment
Specification ≦0.020 ≦1.00 ≦2.00 ≦0.040 ≦0.030 9.00 13.00 18.00 20.00 ー
AUSTENITIC
AUSTENITIC
ＮＳＳＣ
304UL
Typical type 0.014 0.74 1.15 0.024 0.007 10.27 18.51 ー ■Chemical
mass %
%）
ＮＳＳＣ Specification ≦0.020 ≦1.00 ≦2.00 ≦0.040 ≦0.030 12.00 16.00 16.00 18.00 2.00 3.00 C Si Mn P S Ni Cr Mo Cu
316UL
Typical type 0.011 0.70 0.80 0.025 0.004 15.30 16.80 2.35 Specification 1.50 9.50 17.50 0.50 1.50
≦0.08 2.50 ≦1.00 ≦0.030 ≦0.030 11.50 19.50 1.00 2.50
Typical type 0.03 1.90 0.61 0.020 0.001 10.25 17.70 0.69 2.02
NSSC 304UL
NSSC 316UL
■Characteristics
Characteristics
NSSC 110M
Yield strength Tensile
0.2% offset strength Elongation Hardness ■Characteristics
Characteristics
N/mm2 N/mm2 ％ HBW ［Mechanical properties］- Formability-
Specification ≧175 ≧480 ≧40 ≦187 Yield strength Tensile Elongation
ＮＳＳＣ 0.2% offset strength Limit drawing ratio buldge height Erichsen value
304UL N/mm2 N/mm2 ％ L.D.R. mm mm
Typical type 235 549 66 131
Specification ≧205 ≧520 ≧40 ― ― ―
NSSC
ＮＳＳＣ Specification ≧175 ≧480 ≧40 ≦187 110M 320 640 2.3 40.0 12.0
Typical type 52
316UL
Typical type 235 510 65 121 SUS 304 300 680 50 2.3 43.5 13.6
比較例
SUS 316 300 620 46 2.2 40.4 12.4
［Intergranular corrosion resistance］-65% Nitric Acid Corrosion Test; JIS G 0573-
Effects of carbon on susceptibility to intergranular corrosion Effects of heating time on susceptibility to intergranular corrosion
Sensitizing conditions：650℃× 2hr, A.C ［Stress corrosion cracking resistance］
1.5
65%HNO3 Boil 48hr×5 times Test conditions: Spot welding clearance, 200ppm of Cl- ion, 7days
12 65%HNO3 Boil 48hr×5times
Corrosion rate（g/m 2 /hr）
170 No cracking
Corrosion rate（g/m 2 /hr）
Cr:17.9-18.9% 10 Cracking
1.1
Ni:10.2-11.8%
8 150
Test temperature（℃）
6 SUS 304L
0.5 130
4
2 110
ＮＳＳＣ 304UL
0.01 0.02 0.03

0 2 4 6 8 10 12 14 16 90
C（%）
Heating time at 650℃（hr）
70
50
SUS 304 SUS 316 NSSC 110M
AUSTENITIC High-strength, pitting corrosion resistant austenitic stainless steel AUSTENITIC High-strength, high corrosion resistant austenitic stainless steel
NSSC 170 NSSC 317LN
25Cr-13Ni-0.9Mo-0.3N／Corresponding grade : SUS 317J2 19Cr-13Ni-3.5Mo-0.2N-LC／Corresponding grade : SUS 317LN
■Features
STAINLESS STEELS
STAINLESS STEELS
Largely improved resistance to pitting corrosion, one of the critical drawbacks of stainless steels 1. Superior to SUS 316 and SUS 316L in pitting corrosion resistance as well as in chink corrosion resistance
1. Superior to SUS 316 or SUS 317L in pitting corrosion resistance as well as in chink corrosion resistance 2. High performance also in corrosion resistance to acids such as sulfur acid, phosphoric acid or organic acid, etc.
2. Superior to SUS 316 and SUS 317L in oxidation resistance against sulfur acid or hydrochloric acid, etc. and 3. Higher yield strength and tensile strength than SUS 317L and equal level of elongation to SUS 317L
durable to higher acid concentration or higher temperature 4. Equal level of weldability as conventional austenitic stainless steel
3. One and a half times greater high strength than SUS 304, providing with advantage in potential of strength- 5. Corrosion resistance at weld zone is almost equal to that of base metal, with use of welding materials of
oriented designs similar composition
4. High performance also in formability and in weldability
［Typical Applications］ Tank, vessel, chemical plant and others which require higher corrosion resistance than
［Typical Applications］ Exhaust gas desulfurizer, Waste liquid treatment equipment, Sludge treatment equipment, ［Typical Applications］ SUS317L as well as high strength
AUSTENITIC
AUSTENITIC
［Typical Applications］ High temperature usage（cement plant and others）, Plant equipment in general
■Chemical
mass %
%）
■Chemical
mass %
%） C Si Mn P S Ni Cr Mo N
Specification ≦0.030 ≦1.00 ≦2.00 ≦0.045 ≦0.030 11.00 15.00 18.00 20.00 3.00 4.00 0.10 0.22
C Si Mn P S Ni Cr Mo N
Typical type 0.020 0.60 1.38 0.024 0.001 13.18 18.49 3.49 0.14
Specification ≦0.06 ≦1.50 ≦2.00 ≦0.040 ≦0.030 12.00 16.00 23.00 26.00 0.50 1.20 0.25 0.40
Typical type 0.02 0.92 0.55 0.030 0.001 12.91 24.75 0.80 0.34
NSSC 317LN
NSSC 170
■Characteristics
Characteristics
Yield strength Tensile Elongation Hardness
■Characteristics
Characteristics Yield strength
0.2% offset
Tensile strength Elongation Hardness
0.2% offset
N/mm2
strength
N/mm2 % HBW
［Mechanical properties］ N/mm2 N/mm2 % HBW
Specification ≧345 ≧690 ≧40 ≦250 Typical type（t=11.5mm） 314 608 49 158
［Pitting corrosion resistance］［High-temperature strength］

（ASTM G 48 Method B）［High-temperature strength］
［Chink corrosion resistance］
（Test conditions） 700 SUS 316LN
50g/l FeCl3＋1/20N HCI（50℃×48hr） Shape of test piece10mm ×50mm
0.2%Yield strength（N/mm2）, Tensile strength（N/mm2）
（N/mm 2 ）,Tensile strength（N/mm 2）

Test solution：100g FeCl3・6H2O+900ml H2O（6%FeCl3）
15
Test temperature：0 30℃ by 2.5℃ NSSC 317LN
12 NSSC 170 600
800 Test period：72hr
Tensile strength
SUS 316L
Tensile strength
（10 15）
NSSC 304N
10 Grade Base metal Welded joint
SUS 304 Test NSSC 317N SUS 316L 500
600 temperature NSSC 317LN SUS 316L （SMAW）（SMAW）
Corrosion rate（g/m2/hr）
8 SUS 310S 25 × × × ×
（6.9） 400
22.5 × × × ×
0.2%Yield strength
（2-6）
6 400 20 × × × ×
300
17.5 × × × ×
Yield strength
4
15 × × × ×
Yield strength 0.2% offset
0.2% offset
（2.4） 200
12.5 200
2 × × × ×
（0 1）
10 ○ × ○ ×
0
0 7.5 ○ × ○ × 100
NSSC SUS 317M※ SUS SUS 0 200 400 600 800 1,000 1,200
170 329J1 310S 316 5 ○ × ○ ×
2.5 ○ × ○ × 0
※ 317M………………18Cr-16Ni-5Mo 0 100 200 300 400 500
0 ○ × ○ × Temperature（℃）
○：No chink corrosion ×：Generation of chink corrosion
AUSTENITIC Sulfuric-acid resistant austenitic stainless steel AUSTENITIC Seawater-corrosion resistant austenitic stainless steel
NSSC 260,
260, NSSC 260A NSSC 270, NSSC 270R
20Cr-15Ni-3Mo-1.5Cu-0.2N-LC, 22Cr-16Ni-3.5Mo-2Cu-0.2N-LC 20Cr-18Ni-6Mo-0.2N-LC／Corresponding grade : SUS 312L, ASTM S31254
20Cr-23Ni-6Mo-LN
■Features
STAINLESS STEELS
STAINLESS STEELS
1. Exquisite performance in sulfuric-acid resistance 1. Exquisite performance in seawater-corrosion resistance
2. High performance in localized corrosion resistance such as pitting corrosion resistance or chink corrosion resistance 2. High performance also in corrosion resistance to sulfur acid or organic acid
3. One and a half times greater high strength than SUS 304 or SUS 316L 3. Superior to SUS 316 and duplex stainless steels in stress corrosion cracking resistance against chlorides
4. Equal level of weldability as conventional austenitic stainless steel and high performance of welded joint, with 4. One and a half times greater high strength than SUS 304 or SUS 316 in room temperature
use of welding materials of similar composition 5. Equal level of weldability as conventional austenitic stainless steels, with use of welding materials of inconel 625serias
5. NSSC 260A is most suitable for chemical tanker 6. NSSC 270R is most suitable for bar and rod which require cold working
［Typical Applications］ Chimney lining, Exhaust gas desulfurizer ［Typical Applications］ Seawater desalination plant, Seawater heat exchanger, Roofing, Food manufacturing plant,
［Typical Applications］ Corrosion resistant screw, nut and bolt, Wire netting
■Chemical
mass %
%）
AUSTENITIC
AUSTENITIC
C Si Mn P S Ni Cr Mo N Cu ■Chemical
mass %
%）
Specification ≦0.030 ≦1.50 ≦2.00 ≦0.040 ≦0.030 13.50 16.50 18.50 21.50 2.50 3.50 0.16 0.24 1.00 2.00 C Si Mn P S Ni Cr Mo N Cu
NSSC
260 Typical type 0.020 0.50 0.50 0.022 0.001 15.31 20.37 3.20 0.19 1.70 Specification ≦0.020
NSSC ≦0.80 ≦1.00 ≦0.030 ≦0.015 17.00 19.50 19.00 21.00 5.50 6.50 0.16 0.24 0.50 1.00
Specification ≦0.030 ≦1.00 ≦2.00 ≦0.040 ≦0.030 13.00 17.00 20.00 23.00 3.00 4.00 0.10 0.22 1.50 3.00 270 Typical type 0.011 0.49 0.45 0.023 0.001 18.83 20.19 6.13 0.19 0.63
NSSC
260A Typical type 0.018 0.46 0.45 0.021 0.001 16.85 22.26 3.23 0.18 1.72 Specification ≦0.020 ≦0.80 ≦1.00 ≦0.030 ≦0.015 22.00 23.50 19.00 21.00 5.50 6.50 ≦0.05 0.50 1.00
NSSC
NSSC 260A
NSSC 270R
270R
NSSC 260
NSSC 270
Typical type 0.011 0.24 0.59 0.019 0.001 22.72 20.11 6.13 0.02 0.53
■Characteristics
Characteristics
［Mechanical properties］ ■Characteristics
Characteristics
Yield strength Tensile ［Mechanical properties］
Elongation Hardness
0.2% offset strength Yield strength
N/mm2 N/mm2 % HBW Tensile strength Elongation Hardness
0.2% offset
N/mm2 N/mm2 % HBW Hv
NSSC Specification ≧300 ≧650 ≧35 ≦220 ≦230
260 Typical type（t=8mm） 380 705 47 172 NSSC t=10mm 363 755 51 170 ―
〃（t=3.2mm） 370 735 47 191 270 Typical type t=4mm 412 804 45 175 ―
Specification ≧315 ≧600 ≧35 ≦230 t=1.2mm 461 843 39 ― 192
NSSC
260A Typical type（t=16mm） 333 675 52 159 NSSC 270R Typical type（Wire rod） 230 560 47 ― ―
［Localized corrosion resistance］［General corrosion resistance］［Pitting corrosion resistance］

Critical pitting corrosion temperature（CPT）and Critical Arrangement of corrosion rate of various stainless steels Effects of［Ｃｌ-］concentration and temperature to pitting corrosion electric potential
chink corrosion temperature（CCT） by use of general corrosion resistance index（GI）
Test conditions：ASTM G48 Method B NSSC 270 25Cr-7Ni-3Mo（Duplex Stainless Steels） SUS 317
50%H2SO4＋ 1000ppm [CI-],80℃,6hr 1600 1600 1600
100
100
100
Test solution：100g FeCl3・6H2O＋900ml H2O（6％FeCl3） 10 5 Cl- concentration Cl- concentration Cl- concentration
Pitting corrosion potential Vc’

1400 1400 1400
Test period：72hr 10 4 （ppm）（ppm）（ppm）
Fe3＋ 1000ppm 100ppm 1200 1200 1200
20 20 20
CPT（℃） CCT（℃） 10 3 1000ppm 1000 200 1000 1000
200 200
（mV vs SCE）
（mV vs SCE）
（mV vs SCE）
4
10 10000ppm 800 2000 800 2000 800 2000
NSSC 260 40 20 10 2 600 20000 600 20000 600 20000
DX-1
C.R
400 56000 400 56000 56000

400
NSSC 270 70 50 10 1
304 200 200 200
10 3
Corrosion rate（mm/y）
SUS 329JI 55 35 170 0 0 0 0

10
−200 −200 −200
SUS 317L 20 5 329J4L 10 -1
STEN 0 50 100 150 NSSC 170 SUS 316L SUS 444
SUS 316L 15 0 10 2
GI 1600 1600 1600
100
100
100
316C 317LN Cl-concentration Cl- concentration Cl- concentration

1400 1400 1400
270 （ppm）（ppm）（ppm）
260 1200 1200 1200
10 1 B625 20 20 20
1000
（mV vs SCE）
（mV vs SCE）
（mV vs SCE）
1000 200 1000 200
200
316L 800 2000 800 2000 800 2000
317L 600 20000 600 20000 600 20000
316J１L 4563 825 400 56000 400 56000 400 56000
10 0
60 Carpenter20 200 200 200
0 0 0
−200 −200 −200
10 ー1 10 20 30 40 50 60 70 80 90 100 10 20 30 40 50 60 70 80 90 100 10 20 30 40 50 60 70 80 90 100
0 50 100 150 200 Temperature（℃） Temperature（℃） Temperature（℃）
GI＝［Cr］
＋3.6［Ni］
＋4.7［Mo］
＋11.5［Cu］
AUSTENITIC Heat-resistant austenitic stainless steel FERRITIC High-formability ferritic heat-resistant steel
NSSC 305B NSSC 409L
19Cr-13Ni-3.5Si／Corresponding grade : SUS XM15J1 11Cr-0.2Ti-LC／Corresponding grade : SUH 409L
■Features
STAINLESS STEELS
STAINLESS STEELS
Superior to SUS 310S in oxidation resistance in high temperatures Superior to Ti-containing 11Cr heat-resistant steels such as ASTMTP409 or SUH 409 in formability and weldability
Superior to SUS 311S also in high-temperature strength and creep strength 1. High performance in oxidation resistance in high temperatures up to around 750℃
2. With extra-low carbon ferritic structure, it exhibits higher performance in formability and weldability than conventional
［Typical Applications］ Automotive exhaust system, Industrial oven component, Incinerator similar grades
［Typical Applications］ Automotive exhaust system（front pipe, converter, muffler, etc.）, Equipments requiring oxidation
■Chemical
mass %
%）［Typical Applications］ resistance such as heat exchanger or others, Farm machinery, Transformer cases
C Si Mn P S Ni Cr
■Chemical
mass %
%）
≦0.08 3.00 4.00 ≦1.00 ≦0.030 ≦0.030 12.00 15.00 17.50 20.00
AUSTENITIC
Specification
FERRITIC
0.05 3.30 0.90 0.025 0.001 13.23 19.05 C Si Mn P S Cr Ti
Typical type
Specification ≦0.030 ≦1.00 ≦1.00 ≦0.040 ≦0.030 10.50 11.75 10
（C＋N） 0.75
Typical type 0.005 0.45 0.35 0.024 0.001 11.05 0.23
■Characteristics
Characteristics
Yield strength
■Characteristics
Characteristics
0.2% offset ［Mechanical properties］
NSSC 409L
（Thickness：1.2mm）
NSSC 305B
N/mm2 N/mm2 % Hv
Yield strength Tensile Elongation Hardness
Specification ≧205 ≧540 ≧45 ≦200 0.2% offset strength
N/mm2 N/mm2 % Hv
［Oxidation resistance］［Oxidation resistance］

（in air）（in combustion gas）
12
（＊：Occurrence of abnormal oxidation）
Oxidation test Weight loss by oxidation（mg/cm2）
SUS Grade ［High-temperature strength］［Strechability］
0 100 200
Weight amount（mg/cm2 ）
10 ＊ 310S conditions
SUS 304
1200℃ EX.GAS
AIR
8
NSSC 305B EX.GAS 14
1100℃ AIR SPCC
6 NSSC
305B EX.GAS 400
1000℃ AIR 13
EX.GAS NSSC 409L NSSC 409L
Tensile strength（N/mm ）
Erichsen value（mm）
4 1200℃ AIR
2
12
SUS 310S EX.GAS 300
1100℃ AIR
2 SUS 304
11
1000℃ EX.GAS
AIR
0
800 900 1000 1100 1200 EX. GAS: Exhaust gas, intermittent heating（heating for 30 minutes and SUS 430
cooling for 30 minutes）,200 cycles
200 10
Test temperature（℃） AIR: Continuous heating in air for 100 hours SPCC
9
［High-temperature creep rupture characteristics］ 100
10 98 8
Stress （kgf/mm2）
8 Test temperature 800℃

Stress（N/mm2）
6
5 49 0
NSSC 305B 39 7
4 200 400 600 800 0.5 1.0 1.5 2.0
34
3 SUS 310S Temperature（℃ ） Thickness（mm）
2
1 9.8
10 100 1000
Rupture time（hr）
FERRITIC High-formability ferritic heat-resistant steel FERRITIC High-formability ferritic stainless steel
NSSC 430D NSSC PDX
17Cr-0.4Ti-LC,N／Corresponding grade : SUS 430LX 17Cr-0.2Ti-ULC,N／Corresponding grade : SUS 430LX
■Features
STAINLESS STEELS
STAINLESS STEELS
1. Exquisite performance in formability, especially in deep drawability and strechability, a feature of ultra-low- 17% Cr ferritic stainless steel in which high-formability has been realized owing to technological advancement
carbon stainless steel both for steel fineness and for steel sheet producing.
2. Superior to SUS 430 in corrosion resistance 1. High work-limitation and minimal press rising（surface streaks）
3. High performance in corrosion resistance and formability at weld zone. 2. Metal mold for ordinary steel can be applicable, owing to its softness
3. Superior to SUS 430 in corrosion resistance
［Typical Applications］ Home appliance（washing machine's drum, etc.）, Kitchen furnishings, Door knob, Gas burner
4. High performance of weldability and excellence of corrosion resistance and formability at weld zone.
［Typical Applications］ Combustion component, Front door of refrigerator, Battery case, Structural hardware
■Chemical
mass %
%）
C Si Mn P S Cr Ti
■Chemical
mass %
%）
FERRITIC
FERRITIC
≦0.030 ≦0.50 ≦1.00 ≦0.040 ≦0.030 16.00 18.00 Ti≧0.10 and
Specification Ti≧16（C＋N） C Si Mn P S Cr Ti N
Typical type 0.005 0.10 0.11 0.025 0.002 16.39 0.29 Specification ≦0.010 ≦0.50 ≦1.00 ≦0.030 ≦0.030 16.00 18.00 8（C＋N） 0.30 ―
Typical type 0.003 0.06 0.08 0.014 0.002 16.47 0.16 0.009
■Characteristics
Characteristics
■Characteristics
Characteristics
NSSC 430D
NSSC PDX
Yield strength ［Mechanical properties］（Thickness：1.0mm）
0.2% offset Yield strength Tensile
N/mm2 N/mm 2 % Hv Elongation Hardness
Grade 0.2% offset strength
N/mm2 N/mm2 % Hv
Typical type 296 436 32 144 NSSC PDX
SUS 430
［Formability］（Thickness：0.7mm）［Drawability］

［Formability］（Thickness：0.5mm）［Limit drawing ratio -TZP test-］
Ｘ
r value ｎvalue Erichsen value Conical-cup （Test conditions） 65Ｒ
250
540
mm value Blank size（ｍｍ）：see the right figure Erichsen value Ridging rank （Test conditions）
・Thickness of test specimens：0.5mm
250 Grade r value ｎvalue
Press conditions：blank holding force of 35 tons mm ・Blank diameter：80 130mmφ
NSSC 430D 1.67 0.27 10.0 27.0
Lubricant ：Johnson Wax ＃122 ・Punch diameter：50mmφ
NSSC PDX 2.0 0.27 11.2 A
SUS 430 1.18 0.23 9.3 28.4 540 ・Punch shoulder Ｒ：5mm
SUS 430 1.1 0.18 9.3 B
20R ＨＨ Ridging rank A: surface streaks of ≦10μm at tensile test

6R 2.5
180 ［Characteristics of welded portion（in case of TIG weld）］

1st draw
2.32
［Corrosion resistance］ 160 Erichsen value Results of intergranular
Limit drawing ratio（LDR）

corrosion resistance test 2.3
（mm）（Strauss test）
3% solution of salt; 3% solution of salt; 140 2nd draw（restrike）
Grade
dip & dry immersed
Drawing depth（mm）
120 Blank holding force NSSC PDX 10.2 No intergranular corrosion

NSSC 430D ○ ○ 45Ton
○ ○ （SUS 304） SUS 430 3.0 Generation of intergranular 2.1
100 corrosion（desulfurization）
SUS 430 △ △ NSSC 430D
△ ○ 2.08 2.08
80 SUS
430
Remarks）○: Ratio of rusted area is less than 1%
60 1.9
Remarks）△: Ratio of rusted area is between 1% and 5%
40
20
1.7
0 NSSC PDX SUS 430 SUS 304
50 70 90 110 130 150
Blank size（Xmm）
FERRITIC High stain-resistant ferritic stainless steel FERRITIC High stain-resistant ferritic stainless steel
NSSC 160R NSSC 432
17Cr-0.4Cu-Nb-LC,N 17Cr-0.5Mo-0.2Ti-LC,N ／Corresponding grade : SUS 436J1L
■Features
STAINLESS STEELS
STAINLESS STEELS
Developed as material for wire rod of advanced stain resistance without adding Ni or Mo Lower cost than SUS 436L by reduction of Mo content
1. Superior to existing SUS 430 in stain resistance 1. Equal level of formability as SUH 409L, while slightly inferior to SUS 436S in application performance such as
2. Less work hardening than SUS 304 and superior to it in elongation condensate corrosion resistance, salt corrosion resistance etc.
3. High performance of weldability, especially of corrosion resistance around weld zone and extensibility ［Typical Applications］ Automotive exhaust system, Kitchen furnishings, Home appliance, Building interior material, Gate, Handrail
［Typical Applications］ A variety of wire nettings, Fastening products, Precision machine component, Automotive component
■Chemical
mass %）
%
■Chemical
mass %
%）
C Si Mn P S Cr Mo Ti N
C Si Mn P S Cr Cu Nb N Nb/
（C＋N）
Specification ≦0.010 ≦0.14 ≦0.20 ≦0.035 ≦0.006 17.00 18.00 0.45 0.65 10（C＋N） 0.30 ≦0.015
NSSC 160R ≦0.02 ≦1.00 ≦1.00 ≦0.040 ≦0.006 16.00 18.00 0.30 0.60 0.30 0.60 ≦0.02 ≧10 Typical type 0.005 0.10 0.12 0.026 0.001 17.20 0.50 0.22 0.010
FERRITIC
FERRITIC
Typical type 0.01 0.40 0.50 0.035 0.005 16.10 0.40 0.50 0.01 20
■Characteristics
Characteristics
■Characteristics
Characteristics
［Mechanical properties］［Formability］
［Mechanical properties］［Physical properties］
Thermal Elongation Hardness r value ｎ value
Yield strength Tensile Wire Electric resistivity Thermal Specific 0.2% offset strength
strength Elongation Drawing Density expansion ratio conductivity N/mm2 N/mm2 % Hv
0.2% offset （μΩ-xcm）（/℃）（W/m・℃） heat
（g/cm3）
NSSC 160R
NSSC 432
N/mm2 N/mm2 % % ［20℃］［0 800℃］（100℃）（J/kg/℃） Specification ≧205 ≧390 ≧25 ≦170 NSSC 432 1.74 0.26
Typical type 260 430 32 82 Typical type 7.70 62 11.8x10-6 26.0 460 Typical type 245 450 34 134 NSSC 436S 1.61 0.24
（Data of 5.5φ wire rod） NSSC 409L 1.30 0.24
［Stain resistance］［Formability］
Salt spray test（SST） 100
Limit working ratio to shear crack（％）※
5％NaCl, 35℃, 1000h Area of shear ［Corrosion resistance］
crack occurrence
（inferior） Stain resistance rating （superior） 95 （1）Salt spray test
Maximum pitting-corrosion depth（μm）

F E D C B A （Test conditions） 1000 NSSC 409L
NSSC 160R Artificial seawater/ASTM standard
90 800
One cycle consists of 'spraying for 4 hours,
SUS 430 drying for 2 hours and wetting for 2 hours' 600
SUS 304
85 400
200 NSSC 432

80 NSSC SUS SUS NSSC 436S
160R 304J3 XM7
100 200 300 400 500
Number of cycles
Austenitic Stainless
※Limit working ratio to shear crack after two-stepped cold
（2）Automotive exhaust gas test
（μm）
forging of wire edge（as mimic working of screw head）
using mimic condensate
■Application
Application Examples 500
Maximum pitting-corrosion depth

Stainless steel fasteners（screw, nail, bolt, etc.） Wire netting（for industrial machinery or building materials, etc.） 400 NSSC 409L
One cycle consists of 'partial immersion in condensate,
heating at 130℃ for 4 hours and cooling'
300
Condensate: 50ppm［Cl-］,100ppm［SO 2-4 ］, NSSC 432
500ppm［CO 2- ］,220ppm［NH-］,
3 4 200 NSSC 436S
pH8.5
100
0
30 60 90 120 150
Number of cycles
・Replacement from nickel-based stainless steel（VA）・Replacement from nickel-based stainless steel（VA）
・Replacement from plated steel products（improved durability）・Replacement from plated steel products（improved durability）
・Magnetic tools compatible ・Enabling magnetic detection and removal of fragments in wire netting
FERRITIC High stain-resistant ferritic stainless steel FERRITIC High stain-resistant ferritic stainless steel
NSSC 436S NSSC 180
17Cr-1.2Mo-0.2Ti-LSi-LC,N／Corresponding grade : SUS 436L 19Cr-0.4Cu-0.4Nb-LC, N／Corresponding grade : SUS 430J1L
■Features
STAINLESS STEELS
STAINLESS STEELS
High performance of corrosion resistance, especially pitting corrosion resistance, and weldability met in this Stepped up stain resistance with no Mo addition
grade which has been developed by adding Mo and Ti to high purity ferritic base material. 1. Almost equal level of stain resistance as SUS 304
1. Superior to SUS 430LX in corrosion resistance and high performance of weldability owing to its softness 2. Superior to SUS 430 in extensibility and formability as a feature of low-carbon stainless steel
2. High performance of intergranular corrosion resistance as well as drawability in weld zone 3. Exquisite performance in high-temperature characteristics such as oxidation resistance, high-temperature strength, etc.
［Typical Applications］ Automotive exhaust system, Kitchen furnishings, Home appliance, Building interior material, Gate, Handrail ［Typical Applications］ Automotive trim material, Automotive exhaust system, Kitchen furnishings, Home appliance,
［Typical Applications］ Solar-heat collector, Gate, Handrail
■Chemical
mass %
%）
■Chemical
mass %
%）
C Si Mn P S Cr Ｍｏ Ti N
C Si Mn P S Ni Cr Cu Nb N
FERRITIC
FERRITIC
Specification ≦0.010 ≦0.14 ≦0.20 ≦0.040 ≦0.006 17.00 18.00 1.00 1.50 10（C＋N） 0.35 ≦0.015
≧10（C＋N）and
Typical type 0.005 0.10 0.09 0.022 0.002 17.20 1.22 0.23 0.011 Specification ≦0.02 ≦1.00 ≦1.00 ≦0.040 ≦0.006 ≦0.60 19.00 21.00 0.30 0.60 0.30 0.80 ≦0.025
Typical type 0.013 0.51 0.12 0.024 0.002 0.30 19.15 0.41 0.40 0.017
■Characteristics
Characteristics
［Mechanical properties］［Formability］（Thickness：1.2mm）
Yield strength Tensile ■Characteristics
Characteristics
NSSC 436S
Conical-cup
Elongation Hardness ｎ value Erichsen value
NSSC 180
0.2% offset strength ｒvalue mm
N/mm2 N/mm2 % Hv mm ［Mechanical properties］［Formability］（Thickness：0.8mm）
Yield strength Tensile Marginal
Specification ≧205 ≧390 ≧25 ≦170 NSSC 436S 1.61 0.24 10.7 45.6 Elongation Hardness ｒvalue contraction Buldge height Erichsen value
N/mm2 N/mm2 % Hv ratio mm mm
NSSC 180 1.14 0.24 9.9 46.8 ≧205 ≧450 ≧22 ≦200
Specification
NSSC 180 1.41 2.3 31.5 9.6
NSSC 409L 1.30 0.24 ― ― Typical type 314 500 32 153
［Corrosion resistance］
（1）Measurement of pitting corrosion potential （2）Salt spray test ［Formability / Limiting deformation curve］［Stain resistance］
（Test conditions）（Test conditions）
Measurement conditions: 30℃, 3.5% NaCl solution, Ar deaeration Artificial seawater/ASTM standard
0.5%NaCl＋0.2%H2O2, 35℃, 24ｈ
ｒ Based on JIS Z 2371
Potential sweep rate：20ｍＶ/ｍｉ
ｎ One cycle consists of 'spraying for 4 hours, drying for 2 hours
ex : strain to X axis
and wetting for 2 hours' 80
ey : strain to Y axis Grade Surface（superior） Stain resistance rating （inferior）
ex（％）
finishes A ＢＣＤ E F
300 1000 70
NSSC 409L 2B
Pitting corrosion potential（mV vs SCE）
800 60 SUS 304

NSSC 180 BA
600 50 NSSC 180 HL
250 SUS 430
400 40 2B
n
436S NSSC 180 itio
n itio SUS 430 BA
200 nd
30 c ond n co
NSSC 436S in sio HL
stra ten
ne ial
200 100 200 300 400 500 Pla x 2B
Number of cycles Uniaxial tension 10 Dia
SUS 304 BA
condition
HL
-20 -10 0 10 20 30 40
（3）Automotive exhaust gas test using mimic condensate ey（％）
150
One cycle consists of 'partial immersion in condensate,
heating at 250℃ for 3 hours and cooling'
100 , NO -3］, pH 8.9
Condensate：1000ppm［Cl-］,5000ppm［SO 24-］,100ppm each of［CO23-］［
17
15 19 21 23
Cr＋3×Mo（%） 300 NSSC 409L
NSSC 180
200
NSSC 436S
100
0 10 20 30 40 50
Number of cycles
FERRITIC High corrosion resistant ferritic stainless steel FERRITIC High corrosion resistant ferritic stainless steel
NSSC 190
190 NSSC 190
190 L
19Cr-2Mo-Nb,Ti-LC,N／Corresponding grade : SUS 444 19Cr-2Mo-Nb-V-LC,N／Corresponding grade : SUS 444
■Features
STAINLESS STEELS
STAINLESS STEELS
Much higher performance of stress corrosion cracking resistance than austenitic stainless steels as well as Developed on the basis of NSSC 190, exclusively for the usage as heavy plate, it exhibits high performance of
highly improved performance of intergranular-, pitting- and chink- corrosion resistances（NSSC 190 is suitable toughness and weldability in the shape of plate with large thickness
for sheets or wire rod, while NSSC 190L is suitable for plates.） 1. High performance of toughness in both base metal and weld zone at the temperature of 0℃ or more
1. Exquisite performance of stress corrosion cracking resistance and intergranular corrosion resistances 2. Exquisite performance of stress corrosion cracking resistance
2. Superior to SUS 304 in pitting corrosion resistance and chink corrosion resistance 3. Higher level of pitting corrosion resistance or chink corrosion resistance than SUS 304, and especially as high
3. High performance of formability and weldability performance of pitting corrosion resistance as SUS 316
4. Superior to SUS 304 in oxidation resistance, and to SUS 316 in organic acid resistance
［Typical Applications］ Hot-water boiler, Solar-heat collector, Water tank 5. Recommended as material for end plate, welded tube, clad plate or others because of its high performance of
weldability and formability
■Chemical
mass %
%）
FERRITIC
［Typical Applications］Petroleum refining equipment, Petro-chemical equipment, Desalinization equipment,
FERRITIC
C Si Mn P S Cr Mo N Ti＋Nb
［Typical Applications］Industrial heat exchanger, Town gas manufacturing facility, Cl- containing device, Hot water tank
Specification ≦0.015 ≦0.50 ≦0.50 ≦0.040 ≦0.030 18.00 20.00 1.75 2.25 ≦0.015 ≧16（C＋N）
Typical type 0.007 0.14 0.12 0.030 0.002 18.77 1.90 0.011 0.421
■Chemical
mass %
%）
C Si Mn P S Cr Mo Nb V N
■Characteristics
Characteristics Specification ≦0.015 ≦0.50 ≦0.50 ≦0.040 ≦0.030 18.00 20.00 1.75 2.25 ≧8（C＋N） ≦0.20 ≦0.015
［Mechanical properties］［Stress corrosion cracking resistance］
N S S C 19 0 L
Typical type 0.004 0.07 0.07 0.025 0.003 18.75 1.82 0.156 0.06 0.008
N S S C 19 0
Yield strength Tensile Elongation

Hardness （1）42%MgCl2 Solution
N/mm2 N/mm2 % Hv
Load stress ■Characteristics
Characteristics
Specification ≧205 ≧450 ≧22 ≦200 Grade Rupture time
（kgf/mm2）（N/mm2）［Mechanical properties］
Typical type 358 533 29 172 27 265 No rupture after 1,000 hours Yield strength Tensile Elongation Hardness Bending
NSSC 190 30 294 〃 N/mm2 N/mm2 % HBW 180°
32 314 〃 Specification ≧245 ≧410 ≧22 ≦217 t＜8 0.5t, t≧8 1.0t
［Pitting corrosion resistance］ 15 147 Rupture after 3 hours
SUS 304 t=6mm 412 500 35 166 No cracking
20 196 Rupture after 1 hours Typical type
5%FeCl3+N/20 HCI Test (48 hours) 15 147 Rupture after 7 hours t=12mm 392 500 35 170 No cracking
50.0 SUS 316
20 196 Rupture after 4 hours
［Pitting corrosion resistance］［Stress corrosion cracking resistance in High-temperature chloride solution］
（2）High-temperature chloride solution
（Test conditions）（Test conditions）
（Test conditions） Test solution：50g/l FeCl3＋HCｌ Cl-：600ppm and NaCl added（Test solution was renewed every 100 hours）
10.0 Pure water and NaCl (Cl- concentration: 30/600ppm),300℃（87㎏/mm2） Test period：48hr Test temperature：300℃
Test piece：1mmt×15mmw×100mmL（10R U-Bend） Test piece：6mmt×30mmφ Pressure：87kg/cm2
5.0
Cracking Surface finish：Full surface finished with #320 polish Test piece：U-bent type for stress test
Grade Heat treatment Cl-concentration
100hr 200hr 300hr Welding Welding Heat input Result of microscopic
30 ○○○○○○ Base metal material observation
method kJ/cm
Solution TIG welding Anneal SUS 304L
Grade 600 ○○○○○○
condition condition NSSC 190 SUS 316L 10.8 No occurrence of stress corrosion cracking
30 ○○○○○○ 30
1.0 NSSC 190 Sens
600 ○○○○○○
NSSC 190L 14.4 No occurrence of stress corrosion cracking
SUS 430 TIG
0.5 SUS 304 30 ○○○○○○ NSSC 190L D316UL 19.3 No occurrence of stress corrosion cracking
Anneal
SUS 316 600 ○××−−− 24.0 No occurrence of stress corrosion cracking
SUS 304
30 ○○××−− 20
20 30 40 50 Sens Arc manual welding 13.4 No occurrence of stress corrosion cracking
600 ○××−−−
Temperature（℃） Arc manual Transgranular-type stress corrosion
30 ○○○○○○ SUS 304L D308L 15.0
Anneal welding cracking in base metal
600 ××−−−−
SUS 316 SUS 304L Arc manual Transgranular-type stress corrosion
SUS 316L
30 ○○○○○× 10 SUS 316L D316L 15.0
Sens welding cracking in base metal and weld zone
600 −−−−−−
（Heat treatment）
Anneal：no further working as produced NSSC 190L
Sensitizing conditions：NSSC 190 1200℃×5min, A.C.
Sensitizing conditions：SUS 304,316 650℃×2hr, A.C. 0
20 30 40 50 60
FERRITIC High stain-resistant ferritic stainless steel FERRITIC Oxidation resistant ferritic stainless steel
NSSC 220M NSSC 405Si
22Cr-1.5Mo-Nb, Ti-LC,N ／Corresponding grade : SUS 445J2 12Cr-2Si-0.15Al
■Features
STAINLESS STEELS
STAINLESS STEELS
High performance of stain resistance is available in this grade which has been developed by combined addition 1. Exquisite performance of oxidation resistance at high temperatures
of Ti and Nb to 22%Cr-2%Mo ferritic base material. 2. Insignificant thermal deformation owing to its low thermal expansion coefficient
1. Superior to SUS 316 in stain resistance 3. High formability which facilitates cold working and welding
2. Owing to its low thermal expansion coefficient, suitable for such applications that require high resistance to
thermal expansion or contraction as roof, exterior wall, etc. ［Typical Applications］ Combustion tube of oil-burning stove, Component of burners or firing furnaces
3. Exhibits a little higher hardness than SUS 304
■Chemical
mass %
%）
［Typical Applications］ Building exterior materials such as roofing, siding or others
C Si Mn P S Cr Al
Specification ≦0.080 1.00 3.00 ≦1.00 ≦0.040 ≦0.030 11.50 14.50 0.10 0.30
■Chemical
mass %
%）
0.07 1.75 0.12 0.021 0.004 13.02 0.12
Typical type
FERRITIC
FERRITIC
C Si Mn P S Cr Ni Mo N （Ti＋Nb）
（C＋N）
/
Specification ≦0.010 ≦1.00 ≦1.00 ≦0.040 ≦0.007 22.00 23.00 ≦0.60 1.50 2.50 ≦0.020 ≧16
Typical type 0.005 0.10 0.13 0.026 0.001 22.29 0.10 1.63 0.013 28.92
■Characteristics
Characteristics
■Characteristics
Characteristics ［Mechanical properties］
NSSC 405Si
NSSC 220M
［Mechanical and physical properties］ Yield strength Tensile Elongation Hardness

Yield strength Tensile Elongation Hardness Bending N/mm2 N/mm2 % Hv
Average thermal expansion coefficient
N/mm2 N/mm2 % Hv 180° （multiplied by10-6/℃） ≧295 ≧490 ≧15 ≦230
Specification
Specification ≧295 ≧470 ≧22 ≦200 1.0t ― 530 660 19 210
Typical Hot-rolled sheet
Typical type 370 516 30 175 No cracking 10.4 （30 100℃） type Cold-rolled sheet 345 560 28 180
［Corrosion resistance］
（1）Stain resistance and content of Cr and Mo
（Test conditions）［Oxidation resistance］

：Generation of rust 5% NaCl solution, 60℃
3 Oxidation test inside an oil-burning stove Intermittent oxidation test in the air
：No rust Repetition of a cycle of spraying,
The figure below shows the relationship between oxidation
wetting and drying by 100 times Surface
Mo content（％）
Grade finishes 50ｈ 100ｈ 200ｈ 600ｈ amount and repetitive reheating to 1,000℃ for 30 minutes.
（one cycle takes 24hours）
2
NSSC 405Si #400 polished ○ ○ ○ ○
Oxidation amount（mg/cm 2）
SUS 430 2Ｂ × × × × 20
1 Heating pattern
SUS 430
SUH 409 2Ｂ × × × × 1000℃×30min
15 Occurrence of (in the air)
abnormal oxidation Air cooling
Hanged from combustion tube of a small-sized oil-burning stove with reflex mirrors 10
0
○：No rust ×：Generation of red rust Room
temperature 15min
15 20 25
5
Cr content（％） NSSC 405Si
0
（2）Repetitive drying and wetting accelerated corrosion test -100
SUS 304
（Test method） -200
Repetition of a cycle of seawater spraying in room temperature, drying at 60℃ for 30 minutes -300
and wetting at 50℃, 100%, for RH 30minutes by 10 times 100 200 300
Ratio of rusted area（%）
Numbers of heating cycle

100
SUS 304
80
SUS 316
60 NSSC 220M
40
20
0
0 1 2 3 4 5 6 7 8 9 10
Number of cycles
FERRITIC Heat resistant ferritic stainless steel FERRITIC Heat resistant ferritic stainless steel
NSSC FHZ NSSC 450MS
13Cr-1Si-Nb-LC 14Cr-0.5Mo-0.3Nb-0.1Ｔｉ-LC
■Features
STAINLESS STEELS
STAINLESS STEELS
Stepped up high-temperature characteristics by addition of Nb Stepped up high-temperature characteristics by combined addition of Nb, Ti and Mo
1. Endowed with high performance of high-temperature strength and thermal fatigue characteristics by addition of Nb 1. Superior to NSSC 180 in thermal fatigue characteristics in high-temperature and high-temperature strength
2. Superior to SUH 409L in oxidation resistance because of its high content of Si 2. Exquisite performance of oxidation resistance in high-temperature air up to around 950℃
3. Superior to NSSC 180 also in formability such as strechability and drawability
［Typical Applications］ Automotive exhaust system（exhaust manifold，front pipe，etc．），
［Typical Applications］ Plant component（waste-heat boiler duct of power plan and others）［Typical Applications］ Automotive exhaust system（exhaust manifold，etc．
），Smoke duct，Heat exchanger，
［Typical Applications］ Heat-resistant apparatus
■Chemical
mass %
%）
C Si Mn P S Cr Nb N ■Chemical
mass %
%）
Specification ≦0.020 0.80 1.40 0.20 1.20 ≦0.040 ≦0.010 13.00 15.00 0.40 0.80 ≦0.025 C Si Mn P S Cr Mo Nb Ti N
FERRITIC
FERRITIC
Typical type 0.010 1.12 0.45 0.022 0.001 13.21 0.43 0.006 Specification ≦0.015 ≦2.00 ≦2.00 ≦0.040 ≦0.030 13.50 14.50 0.40 1.00 0.20 0.50 0.10 0.30 ≦0.015
Typical type 0.010 0.94 0.95 0.029 0.005 13.90 0.50 0.30 0.13 0.010
■Characteristics
Characteristics
［Mechanical properties］ ■Characteristics
Characteristics
NSSC 450MS
Yield strength Tensile Elongation Hardness ［Mechanical properties］
NSSC FHZ

N/mm2 N/mm2 % Hv Yield strength Tensile Elongation Hardness
Hv r value
Specification ≧205 ≧410 ≧25 ≦200 N/mm2 N/mm2 %
Typical type 311 492 34 152 Specification ≧205 ≧390 ≧25 ≦200 ー
Typical type 297 471 34 160 1.28
［Oxidation resistance］［Thermal fatigue characteristics］［Oxidation resistance］［High-temperature tensile characteristics］
Intermittent oxidation test at 950℃
Yield strength 0.2% offset

Continuous oxidation test in air（200 hours） 400
Oxidation amount（mg / cm2）

2.0
0
950℃-in air NSSC 180
（N/mm2）
300
Minimum temperature = 200℃, 30min.in high temp.
1.5
50％ restrained（n=0.5） NSSC 450MS
Thermal fatigue lifetime（cycles）
SUH 409L 200

80 A.C.
1.0 100
NSSC 450MS
0
60 0 200 400 600 800 1000
103 0.5
tensile strength （N/mm ） Tensile strength（N/mm ）

500
2
0.0 400 NSSC 450MS
40 0 100 200 300 NSSC 180
Number of cycles 300
：NSSC FHZ
200
：SUS 430J1L
20 100
：SUH 409L
SUS 430J1L ［Thermal fatigue characteristics］ 0
0 200 400 600 800 1000
→
→ （Test conditions）
←
0 NSSC FHZ
2mmt, 100％ restrained, 900℃/200℃ 50
2
102 NSSC 180
800 900 1000 700 800 900 1000 TS
40 NSSC 450MS
NSSC 180 0.2％
Yield strength 0.2% offset/

Temperature（℃） Maximum temperature Tmax（℃） NSSC NSSC 450MS PS
450MS 30
20
NSSC
180 10
0 200 400 600 800 1000 800 900 1000
Thermal fatigue lifetime in cycles（cycles） Temperature（℃）
FERRITIC Heat resistant ferritic stainless steel FERRITIC Oxidation- and electric-resistant ferritic stainless steel
NSSC FH11 NSSC HOM
18Ｃｒ-2.5Sｉ-Ｎｂ-ＬC 15Cr-4Al-LC,N
■Features
STAINLESS STEELS
STAINLESS STEELS
Stepped up high-temperature characteristics by addition of Si and Nb 1. Distinguished performance of oxidation resistance owing to its forming of alumina oxide on surface in high-
1. High performance of rust resistance in burning atmosphere as well as in high-temperature humid atmosphere temperature atmosphere
2. Superior to SUS 430 in high-temperature strength 2. Insignificant thermal deformation caused by heating or cooling owing to its low thermal expansion ratio
3. Large scale of electric resistivity
［Typical Applications］ Combustion parts of heater, etc.
［Typical Applications］ Combustion tube of oil-burning stove，Grid resister of cars or ships
■Chemical
mass %
%） ■Chemical
mass %
%）
C Si Mn P S Cr Nb C Si Mn P S Cr Aｌ
Specification ≦0.030 2.40 2.80 ≦1.00 ≦0.040 ≦0.030 17.50 18.50 0.20 0.50 Specification ≦0.015 ≦1.00 ≦1.00 ≦0.040 ≦0.030 14.00 16.00 3.00 5.00
FERRITIC
FERRITIC
Typical type 0.020 2.59 0.29 0.022 0.001 18.22 0.31 Typical type 0.003 0.20 0.12 0.024 0.001 15.00 4.60
■Characteristics
Characteristics
［Mechanical properties］［Mechanical properties］
Yield strength Tensile Elongation in Hardness in Yield strength Tensile
NSSC FH11
Elongation Hardness
NSSC HOM
0.2% offset in strength in 0.2% offset strength
N/mm2 N/mm2 % Hv/1kg % Hv
N/mm2 N/mm2
Specification ≧205 ≧410 ≧22 ≦230 Specification ≧350 ≧520 ≧15 ≦230
Typical type 431 588 29 203 Typical type 493 656 24 208
［Oxidation resistance］［Physical properties］

Specific gravity Electric resistivity Average thermal expansion coefficient
（High-temperature humid atmosphere）（Air atmosphere）
2.0 7.20 125±6μΩ・cm（at 20℃） 11.5×10-６
（1/ ℃）
（20 500℃）
Atmosphere：5%O2-20%H2O-Ar 110 Continuous heating for 200 hours in air
Period：20hr （* denotes abnormal oxidation）
90
＊（* denotes rust generation）
SUH 409 SUS 304 ［Oxidation resistance］
70 ＊＊
Intermittent oxidation test in the air
SUS 430 50
1.0 ＊ SUS 430 （Test condition）
30 ＊＊ Heating conditions: One cycle consists of '30 minutes at 1200℃ and 30 minutes at room temperature'
NSSC 405Si
＊ NSSC SN9 Test specimens: thickness×20×50mm
10 ＊
＊ 5
NSSC FH11
4 ＋2
0
3 ＊ NSSC HOM
NSSC FH11 0
2
Weight loss（g）
1
ー2
SUS 430
0 Complete oxidation
600 700 800 600 700 800 900 1000 1100
ー4
Temperature（℃） Temperature（℃）
ー6
ー8
SUS 304
Complete oxidation
0 20 40 60 80 100 200 300 400

Number of cycles
FERRITIC High weldability ferritic stainless steel FERRITIC High weldability ferritic stainless steel
NSSC 410W NSSC 410WM（YUS
YUS 410W-MS
410W-MS）
12Cr-LC／Corresponding grade : SUS 410L 11Cr-Ni-LC,N／Corresponding grade : SUS 410L
■Features
STAINLESS STEELS
STAINLESS STEELS
Stepped up welding workability and mechanical properties at weld zone High performance of yield strength, weldability and weld zone characteristics and therefore suitable for welded
1. High performance of weldability which enables MIG welding and arc welding without pre- and post- heating. structure of thickness over 3mm above all
2. High performance of bending workability and toughness of welded joint 1. Distinguished performance of weldability which enables welding without pre- and post- heating.
3. Exhibits wide range of mechanical properties according to choice of heat-treating conditions 2. High performance of bending workability and toughness of welded joint
4. Equal level of corrosion resistance and high-temperature oxidation resistance as conventional grade as SUS 410L 3. Superior to SUS 410 in yield strength which provides with advantage in potential of strength-oriented designs
4. YUS 410W-MS is an accredited grade of Article 37 of the Construction Standard Act
［Typical Applications］ Heat-resistant equipment, Other equipments or building materials used in environmental
［Typical Applications］ conditions which don't require highest level of corrosion resistance ［Typical Applications］ Marine container frame material，Structural construction material，Other materials which
［Typical Applications］ require both high yield strength and bending workability
FERRITIC
FERRITIC
■Chemical
mass %
%） ■Chemical
mass %
%）
C Si Mn P S Cr
C Si Mn P S Ni Cr N
Specification ≦0.030 ≦1.00 ≦1.00 ≦0.040 ≦0.030 11.50 13.50
Specification ≦0.030 ≦0.50 ≦1.00 ≦0.035 ≦0.025 ≦0.50 10.75 12.00 ≦0.025
Typical type 0.020 0.48 0.53 0.022 0.002 11.75
Typical type 0.022 0.12 0.85 0.021 0.002 0.38 10.85 0.008
（YUS 410W-MS）
NSSC 410W
NSSC 410WM
■Characteristics
Characteristics
［Mechanical properties］［Mechanical properties］
Yield strength Tensile Elongation Hardness Bending Yield strength Tensile
0.2% offset strength Elongation Hardness
% Hv Angle Inside radius 0.2% offset strength
N/mm2 N/mm2 N/mm2 N/mm2 % Hv
Specification ≧195 ≧360 ≧22 ≦200 180° 1.0t Specification Plate thickness ≧315 ≧430 ≧20 ≦240
Typical type 284 462 30 145 No cracking t=4.5mm 412 510 28 157
Typical type
t=6.4mm 392 490 31 153
［Mechanical properties after temper heat treatment］
Tempering Yield strength Tensile Elongation Bending Hardness
temperature 0.2% offset strength
Hv ［Bendability］
℃ N/mm2 N/mm2 % (r=1t)
Thickness Bending Inside
700 481 627 22.0 No cracking 187 Judgment
（mm） angle radius
750 320 523 27.6 No cracking 170
t≦5.0 90° 1.0t No cracking on outside bent zone
800 285 490 32.8 No cracking 136
Specification 5.0＜t≦6.4 〃 1.5t 〃
（Thickness：8mm）
6.4＜t 〃 2.0t 〃
［Mechanical properties of welded joints］
t=4.5 〃 1.0t No cracking
Rupture impact test * Typical type
Tensile t=6.4 〃 1.5t No cracking
Welding Welding Thickness strength Rupture
Grade vE0 vE20 vTrs Bending test **
method materials mm N/mm2 location
J J ℃ （Test specimens: JIS No.4）
Base metal − 9.5 549 − 51.0 61.8 ＜−100 r＝1.0t No cracking ［Toughness］
MIG YM-309 〃 Dle Base metal 66.7 74.5 −60 r＝2.0t No cracking NSSC 410WM TP 409
NSSC 410W Thickness
Arc hand 309R 〃 557 〃 54.9 69.6 −18 r＝2.0t No cracking Direction vE0 vE20 vTrs vE0 vE20 vTrs
（mm） J J ℃ J J ℃
〃 410Nb 〃 556 〃 44.1 59.8 ＋32 r＝2.0t No cracking ＊1 L 29 28 ー86 ーーー
Base metal − 7.0 − − 30.4 32.4 −35 4.5
C 30 29 ー82 ーーー
SUS 405 Arc hand 309R 〃 500 Base metal − 6.9 − ＊2 L 64 73 ー80 32.4 37.3 ー32
〃 410Nb 〃 504 〃 − − − 6.5
C 49 53 ー85 23.5 29.4 ー32
（*Impact test piece: L direction, subsize 5 JIS No.4 **Bending test: L direction, roller bend test）
*1: Subsize 3mm, Charpy test specimens（2mm V-notch）
*2: Subsize 5mm, Charpy test specimens (3mm V-notch)
MARTENSITIC High-strength, high stain-resistant ferritic stainless steel AUSTENITIC-

MARTENSITIC
High-strength, high corrosion resistant duplex stainless steel
NSSC 550 NSSC DX1
13Cr-2Ni-2Mo 22Cr-5Ni-3Mo-LC-0.13N／Corresponding grade : SUS 329J3L, DIN 1.4462
■Features
STAINLESS STEELS
STAINLESS STEELS
1. Superior to SUS 304 in corrosion resistance by appropriate addition of Cr and Mo as well as by control of trace elements Exquisite performance of high-strength and high corrosion resistance corresponding DIN 1.4462
2. Superior to SUS 304 in performances of wire drawing as well as cold-heading 1. Superior to SUS 316 or SUS 317 in pitting corrosion resistance as well as in chink corrosion resistance
2. High performance of yield strength which is twice as high as SUS 304 or SUS 317 at room temperature
［Typical Applications］ Self-tapping screw，High-strength nail，Various kinds of pins，High-strength chain and 3. Equal level of weldability as conventional austenitic stainless steel with use of welding materials of similar composition
［Typical Applications］ other applications requiring high hardness and high stain resistance
［Typical Applications］ A variety of equipments for chemical plant, Body of revolution for centrifugal separator
■Chemical
mass %
%） ■Chemical
mass %
%）
-MARTENSITIC
MARTENSITIC
AUSTENITIC
Specification ≦0.03 ≦1.00 ≦2.00 ≦0.030 ≦0.020 4.50 6.50 21.00 23.00 2.50 3.50 0.08 0.20
Specification 0.10 0.20 ≦1.00 ≦1.00 ≦0.040 ≦0.010 1.00 2.40 12.50 14.00 1.80 2.30 0.05 0.15
Typical type 0.02 0.46 1.75 0.020 0.001 5.15 21.68 2.93 0.13
■Characteristics
Characteristics
［Mechanical properties］［Cold workability］［Mechanical properties］
NSSC DX1
NSSC 550
Longitudinal elastic Transverse elastic Density Thermal expansion 1800 Elongation Hardness Charpy absorbed energy vEo
Tensile strength
modulus modulus coefficient % HBW J

Drawing（％）（N/mm2 ）
g/mm2 1600 N/mm2 N/mm2

N/mm2 N/mm2 cm/℃
1400 Specification ≧450 ≧620 ≧25 ≦290 −
2.05×105 7.94×104 7.75 11.5×10-6 1200
1000 t=6.0mm 588 784 35 216 −
800
Typical type t=12.7mm 549 774 40 224 304
60
［Mechanical properties］ 50 t=20.0mm 510 745 39 226 314
Yield strength Tensile Elongation Hardness Impact 40
0.2% offset strength value 30
N/mm2 N/mm2 % Hv J/cm2 0 10 20 30 40 50 60 70 80 90 100
［Chink corrosion resistance］
After annealing − 872 61 283 − Drawing fabrication rate %
（Test conditions）ASTM G48 Method B
After tempering
at 200℃ （Test conditions）Test temperature：0 25℃
following 1150 1750 29 550 80 （Test conditions）Test solution：100g FeCl3・6H2O＋900ml H2O（6% FeCl3）
annealing
at 1,150℃ （Test conditions）Test period：72hr
Grade NSSC DX1 welds

Test NSSC DX1 SUS 316L SUS 316LN SUS 317L
［Stain resistance］ temperature SMAW SAW SAW
Base metal （12.7t）（12.7t）（20.0t） Base metal Base metal Base metal
（℃）
Pitting corrosion potential Salt spray test 25.0 × × × × × × ×
（Test conditions）（Test conditions）JIS Z 2371, 240 hours
22.5 × × × × × × ×
Solution of 3.5％ NaCl, Ar deaeration at 30℃
NSSC 550 SUS 304 SUS 410 20.0 × × × × × × ×
Pitting corrosion potential（mV vs. SCE）
-100 0 +100 +200 +300 +400 17.5 ○ × ○ ○ × × ×
15.0 ○ ○ ○ ○ × × ×
NSSC 550 12.5 ○ ○ ○ ○ × × ×
10.0 ○ ○ ○ ○ × ○ ○
7.5 ○ ○ ○ ○ × ○ ○
SUS 304
5.0 ○ ○ ○ ○ × ○ ○
2.5 ○ ○ ○ ○ × ○ ○
SUS 410
0 ○ ○ ○ ○ × ○ ○
（○：No chink corrosion ×：Generation of chink corrosion）
Material Safety Data Sheet
Prepared on 1-October-03
1 Product and company identification 5 Fire-fighting measures 11 Toxicological information

Fine particles may be combustible and explosive. At present, we have no effective epidemiological information
［ Product name ］ on the toxicological (health) effects of this steel product. For
Stainless steel sheets and strip some of alloying elements, however, toxicological effects may
Heat-resistant steel sheets and strip 6 Accidental be pointed out, for example, in cases where the concentration
［ Supplier］
release measures of respective element exceeds a certain level (e.g., allowable
concentration) during the operations described in Section 8.
The toxicological information is obtained from, for example, the
Nippon Steel & Sumikin Stainless Steel Corporation As the product is a solid, it is not released under general
ICSC (supervised by the Environmental Health Bureau,
Address ：3-2-2 Nihonbashi-Hongokucho, Chuo-ku, Tokyo conditions.
Ministry of Health and Welfare), etc.
Division in charge ：Technical Division
Telephone number：03-3276-4890
Facsimile number ：03-3276-4928
7 Handling and storage 12 Ecological information
Emergency address and telephone number：Same as above Avoid unnecessary wetting with water, contact with acids and
At present, we have no effective ecological information. For
high-temperature and high-humidity environments. In the case
some of alloying elements, however, environmental effects
of heavy product, take precautions to prevent the possibility of
2 Composition/information on ingredients falling.
may be pointed out. The ecological information is obtained, for
example, from the ICSC (supervised by the Environmental
Health Bureau, Ministry of Health and Welfare). etc.
Substance or preparation Preparation (Alloy)
8 Exposure controls/
Main ingredients personal protection 13 Disposal considerations
Ingredient Name Conc.（％） CAS No. ICSC No. At present, we have no effective information on exposure Basically, disposal is entrusted to legally approved industrial
Iron [ Fe ] Balance 7439-89-6 − controls and personal protection under general conditions. waste management contractors. If there is any substance
Silicon [Si] Under 5 7440-21-3 − When performing welding, autogenous cutting, grinding, adhering to the waste to be disposed of, the contractor is
[Mn] cutting, etc., wear masks, goggles, gloves, work clothes, etc. selected, paying attention to the adhering substance.
Manganese Under 12 7439-96-5 0174
for prevention of fume inhalation and irritation to the mucous
Nickel [Ni] Under 37 7440-02-0 0062
membrane and for protection from arcs and cutting chips.
Chromium
Molybdenum
[Cr]
[Mo]
Under 32
Under 7
7440-47-3
7439-98-7
0029
−
14 Transport information
Copper [Cu]
[Nb]
Under 5 7440-50-8 0240 9 Physical and In the case of heavy product, exercise care for prevention of
Niobium Under 2 7440-03-1 − load shifting. It is desirable to cover the product with tarpaulin
Titanium [ Ti ] Under 3 7440-32-6 −
chemical properties or the like to prevent infiltration of rain water, etc.
Aluminum [Al] Under 5 7429-90-5 − Physical state A silver-white solid under general conditions
｡
Tungsten
Cobalt
[W]
[Co]
Under 3
Under 21
7440-33-7
7440-48-4
−
−
Physical properties Fusion point : 1,455 ~ 1,535 C
Density : Approx. 7.7~8.0 g/cm3
15 Regulatory information
No specific information
3 Hazards identification 4 First-aid measures 10 Stability and reactivity

The product is stable with low reactivity under general
16 Other information
At present, we have no effective information on hazards After receiving the first-aid measure required, consult a conditions. However, rust may appear if the product comes For inquiries, refer to Technical Div., Nippon Steel & Sumikin
identification under general conditions. However, the fumes physician if necessary. Examples of first-aid measures are into contact with water or an oxidizing substance. This rusting Stainless Corporation. phone : +81-3-3276-4890, Facsimile ;
resulting from welding, autogenous cutting, etc. and the fine given below. may be accompanied with a deficiency of oxygen or the +81-3-3276-4928
particles resulting from grinding, etc. may irritate the respiratory ◆ If respiration becomes difficult due to fumes or the like, generation of hydrogen.
organs, the mucous membrane of the eye, etc. Burns may apply a respiratory aid and consult a physician immediately.
result from arcing. Moreover, cutting chips or the like may be ◆ When a burn is caused by arcing or the like, cool the
injurious to the skin. affected part and receive medical treatment if necessary. This data sheet has been drawn up in accordance with ISO information" for securing safe handling of the product.
◆ If the mucous membrane of the eye or the like is irritated by 11014-1 "Safety Data Sheet for Chemical Products", Part 1 Referring to this data sheet, the users should take appropriate
fumes, fine particles, etc., wash the affected part with water "Content and Order of Sections" (hereinafter referred to as safety measures on their own responsibility depending on the
and consult a physician immediately. "ISO"). The definitions of terms conform to ISO. actual state of handling. This data sheet is not intended for
◆ When the skin is injured by cutting chips or the like, keep In this data sheet, the information which is available at assuring the safety of the product. There is a possibility of
the wound clean and receive medical treatment if Nippon Steel & Sumikin Stainless Steel Corp. at the time of hazards which are not described in this data sheet and for
necessary. sheet preparation is furnished to the users as the "reference which our company does not have any specific information.

NSSCGrades Tipos INOX

Uploaded by

Copyright:

Available Formats

NSSCGrades Tipos INOX

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NSSCGrades Tipos INOX

Uploaded by

Copyright:

Available Formats

Introduction to NSSC Series Stainless Steels

Niigata Sales Office

Hikari Works Kashima Works Yawata Works

Printed on recycled paper

Introduction to NSSC Series Stainless Steels 1

Formability, Weldability Formability

Cold forging Mo reduction Welded portion toughness

N SSC 160R N SSC 43 2 NS SC 1 90L

Heat resistance Heat resistance

Pitting-, or intergranular- corrosion resistance

High formability, Design oriented 6.00 15.00

NSSC 304RM2 High formability, Kitchen sink, 9.00 18.00

NSSC 131 Non-magnetic 0.01 3.00 5.00 17.00 0.10

NSSC 304N SUS 304N2 High-pressure equipment, 7.50 18.00 Hv≦260

NSSC 304UL Intergranular corrosion Spent nuclear fuel 9.00 18.00

NSSC 316C Corrosion resistance, Machine screw, 10.00 16.00 2.00

22Cr-16Ni-3.5Mo-2Cu- Oxidation resistance, 20.00 3.00 0.10

NSSC 270R Seawater-corrosion Corrosion resistant screw, 22.00 19.00 5.50

Automotive exhaust 3.00 17.50

NSSC FHZ ー 13Cr-1Si-Nb-LC High-temperature Automotive exhaust system, ≦0.020

NSSC 410DA ー 12Cr-0.07C High hardness Disc brake C Trace 11.50

DIN 1.4462 /intergranular-corrosion resistance Energy-related plat

AUSTENITIC High-formability austenitic stainless steel AUSTENITIC

C Si Mn P S Ni Cr Cu 9.00 18.00 0.5

Yield strength 0.2% offset Tensile strength Elongation Hardness

Specification 7 ：Applied stress20kgf/mm2 ［Season cracking resistance］

6 ［Permeability］- after wire drawing -

NSSC 304JS SUS 304 1.01 NSSC 130M

（NSSC 304JS exhibits only a minimal spring back after press.）

［Mechanical properties］- after solution heat treatment -

2000 30 Typical type 481 814 49 170

25 Specification ≧205 ≧520 ≧40 ≦187

Yield strength 0.2% offset（N/mm 2 ）, Tensile strength（N/mm 2 ）

Yield strength Tensile strength

0.01 0.02 0.03

［Pitting corrosion resistance］ ［High-temperature strength］

（N/mm 2 ）,Tensile strength（N/mm 2）

Yield strength 0.2% offset

［Localized corrosion resistance］ ［General corrosion resistance］ ［Pitting corrosion resistance］

Pitting corrosion potential Vc’

Pitting corrosion potential Vc’

Pitting corrosion potential Vc’

400 56000 400 56000 56000

SUS 329JI 55 35 170 0 0 0 0

Pitting corrosion potential Vc’

Pitting corrosion potential Vc’

［Oxidation resistance］ ［Oxidation resistance］

8 Test temperature 800℃

［Formability］ （Thickness：0.7mm） ［Drawability］

20R Ｈ Ｈ Ridging rank A: surface streaks of ≦10μm at tensile test

180 ［Characteristics of welded portion（in case of TIG weld）］

Limit drawing ratio（LDR）

120 Blank holding force NSSC PDX 10.2 No intergranular corrosion

Maximum pitting-corrosion depth（μm）

200 NSSC 432

Maximum pitting-corrosion depth

800 60 SUS 304

Yield strength Tensile Elongation

［Mechanical and physical properties］ Yield strength Tensile Elongation Hardness

［Pitting corrosion resistance］［High-temperature strength］

［Localized corrosion resistance］［General corrosion resistance］［Pitting corrosion resistance］

［Oxidation resistance］［Oxidation resistance］

［Formability］（Thickness：0.7mm）［Drawability］

20R ＨＨ Ridging rank A: surface streaks of ≦10μm at tensile test

（Test conditions）［Oxidation resistance］

［Oxidation resistance］［Physical properties］