Brick Masonry
Brick Masonry
Brick Masonry
Important Point
There are a number of types of bricks and mortars that can be used to manufacture brick
masonry.
Bonding in brick masonry, which adheres to bricks simultaneously, is constructed by filling
the joints between the bricks with suitable mortar.
Special precautions must be practiced since the mortar is mixed and placed as it greatly
affects the performance and durability of the masonry structure.
Also, read: Type of Brick in Brick Masonry English Bond & Flemish Bond
There is a long list of bricks of such a special size. We will discuss the important ones here.
Squint Brick.
Splay Brick.
Coping Bricks.
Bullnose Brick.
Cownose Brick.
They are cut at a corner at an angle of more than 90 degrees. They are required to shape the
outer or inner corner in a wall.
They have a level or part, width-wise, length, or in both directions. The individual shapes are
grouped under gleaming bricks, which are also made for use indoors and windows, vents, and
plinths.
When a coping is to be provided to a wall, a particular shape may be desired. Chuffed, half-
round, and saddleback bricks are some common imitating bricks.
Bullnose bricks are used on the sides of the wall to obtain round corners. It is a standard brick
with one edge rounded.
It is similar to the bullnose, but it has both sides rounded to one side. It can also be called
double bullnose bricks. They have the same use as bullnose, but they only give additional
roundness.
Types of Bricks
There are almost as many ways of classifying bricks as there are different types of bricks.
But if you classify them based on where they go, you need only remember two: facing bricks and
backing bricks.
Facing bricks are used on the outside of buildings, which means they have to be durable
enough to endure rain, storms, and other unfavourable weather conditions.
Backing bricks, however, are placed behind facing bricks. So, while facing bricks must
be at least mildly pleasant to look at, no one cares what backing bricks look like.
If you are talking to someone about the types of bricks used in construction, there is a good
chance they will classify the bricks they use based on raw materials. In that case, you should
know five basic types.
Different Types of Brick Masonry Work Are Used in the Manufacture of Brick Masonry
Including:
Burnt-clay bricks have good resistance to moisture, insects and erosion and create a good room
environment. They are medium in cost and have medium-to-high compressive strength.
Bricks can be made with sophisticated factory methods, simple labor-intensive methods or a
range of mechanized technologies in between. Burnt clay bricks are made by placing molded
clay into a kiln and firing it up.
These bricks are kind of like white bread: They are versatile and can be used in a lot of
different ways, even if they’re not the most exciting bricks in the world.
Because they’re so popular and widely used, talking about types of brick masonry without
mentioning burnt clay can be a challenge.
There are four classes of burnt clay brick, with first-class offering the best quality and most
strength.
It is made of concrete. It is the least used bricks. It has low compression strength and is of low
quality.
Concrete brick is a mixture of cement and aggregate, usually, sand, formed in moulds and
cured.
Concrete pipe is made of cement, aggregate and cured as above. These bricks are used above
and below the damp proof course.
These bricks are used can be used for facades, fences, and internal brick-works because of
their sound reductions and heat resistance qualities. It is also called mortar brick.
These are a mix of sand, lime, and fly ash. The materials are bonded through a chemical
reaction that takes place in the middle of wet mixing.
If you are looking for a brick that can carry its own weight, try these. They are famous for their
stellar load-bearing capacity.
Fly ash clay bricks are manufactured with clay and fly ash, at about 1,000 degrees C.
Some studies have shown that these bricks tend to fail poor produce pop-outs, when bricks come
into contact with moisture and water, causing the bricks to expand.
Engineering bricks are bricks manufactured at extremely high temperatures, forming a dense and
strong brick, allowing the brick to limit strength and water absorption.
Engineering bricks offer excellent load bearing capacity damp-proof characteristics and chemical
resisting properties.
Ordinary building bricks are generally rectangular in shape, solid in structure and made of
suitable types of brick-clay.
A familiarity with this particular classification of bricks is quite important for a construction
engineer and an architect. We will discuss them below.
Also, read: Test for Compressive Strength of Brick | Water Absorption | Dimensions Test
Brickwork in Mud
Brickwork in Cement
This type of brick is construction done by laying bricks in cement mortar instead of
masonry clay used in brickwork in clay.
There are three major classes of brickwork in cement which are summarized in the table.
Quantity of cement, Sand or Mortar Required for Brickwork 1:n ratio of
cement mortar is usually used for brickwork.
After adding water to the mortar mix, it bulks and reduces the volume by 33% during
the wet condition. In order to calculate the dry volume of cement & sand or Brick
mortar add 33% of extra volume to it.
Stretcher Bond
Header bond
English bond
Flemish Bond
Stretcher bonds are typically used as a facade for the main structural building. It may look very
plain, but very effective with the introduction of other patterns.
Often this bond is used in garden walls, but when considering landscaping you should look for
other attractive bonds such as English bonds or Flemish bonds.
The header is the short face of the brick as seen in height. In a standard brick, it has a 90 mm ×
90 mm face.
In header bond brick masonry all bricks are arranged in header courses as shown in the above fig
This type of bond is useful for building a brick thick walls.
#3. English Bond–
English bond brickwork is where bricks are placed in alternating layers of headers and
stretchers.
The traditional way of laying the course is often replaced by 1 course of headers, then 3–5–7
courses between stretch courses, referred to as garden wall bonds.
Like the Flemish bond, it can be a very difficult bond to get right and will take a lot of practice.
These are alternative bricks that have been placed as headers and stretchers in every course.
Each header is placed up and down immediately in the middle of the stretcher to maintain it
evenly.
Flemish bonds, like others Bond, are rarely used on new modern buildings and are more suited to
garden walls and feature structures. This can be a very difficult bond to get hold of because it
requires great attention to detail.
Note
Brick Masonry
Brick masonry is defined as the placement of bricks in a systematic manner using mortar to
bind the bricks together and create a solid mass that can withstand a great deal of pressure.
There are different types of bricks and mortars that are used to construct brick masonry.
Masonry is a construction method that uses individual units, like brick and stone, bound together
with mortar. It is one of the most durable construction techniques in the world, and it has been
popular for centuries.
A brickmason uses bricks, concrete blocks, structural tiles, and natural and man-made stones to
build walkways, fences, walls, patios, buildings and other structures.
1. Burnt Clay Bricks: Burnt clay bricks are also known as common bricks because they are
the most abundant brick type in modern construction. These bricks are used in columns,
walls, foundations, and more with a wide variety of purposes.
2. Sun-Dried Clay Bricks: Some DIYers might prefer to make these simple sun-dried clay
bricks, which have been used as far back as 7,000 BC in southern Turkey and around the
city of Jericho in modern-day Palestine.
3. Concrete Bricks: Typically used in internal brickwork or to make facades and fences,
these bricks are made from solid concrete. The concrete is poured into custom molds,
allowing manufacturers to create a variety of sizes and shapes.
4. Engineering Bricks: As the name suggests, engineering bricks are a favorite of
structural engineers because of their high compressive strength and density, ideal
qualities for use as load-bearing materials.
5. Sand Lime Bricks: Made using a mixture of sand, lime, and possibly a color pigment to
alter the final appearance of the brick, sand lime bricks have a high compressive strength,
so they are a common option for load-bearing walls in houses and multi-storied buildings.
6. Fly Ash Bricks: Fly ash is a byproduct produced by coal-fired power plants that can
contain toxic metals like mercury, arsenic, antinomy, and chromium.
7. Firebricks: If the goal of the masonry project is to create a structure, wall, or framework
that is highly resistant to heat and fire, then firebricks are the best material.