Fosroc Nitoseal PU40

Formerly Known as Nitoseal HP40 constructive solutions

One part polyurethane sealant

Uses
Cleaning
Nitoseal PU40 sealant is designed for sealing expansion and
Clean equipment immediately after use with Fosroc Solvent
control joints, pre-cast concrete panel joints, window
102.
perimeters, steps, risers, roof and tilt-wall joints and between
construction materials of dissimilar expansion coefficients.

Nitoseal PU40 sealant may be factory or field applied to seal Design Criteria
various construction components. Some substrate surfaces
may require priming for optimum performance. Nitoseal PU40 can be applied to joints between 6 mm and 50
mm wide and applied between 6 mm and 25 mm deep.

Advantages Joints which are expected to experience continual cyclic

movement should be designed such that the sealant is
Single component – minimizes wastage applied to an optimum width to depth ratio of 2:1subject to
the overriding recommended minimum sealant depths of: a)
Easy to Apply 6 mm for accurately formed, non-porous surfaces such as
glass and metal, b) 10 mm for precast concrete, in-situ
UV stable concrete, brick and other porous surfaces.
Strong adhesion to most common building substrates
The sealing slot should be formed using a backer rod which
supports the sealant during application and provides a bond
breaker at the base of the slot to allow movement to be
Standard compliance accommodated over the full width of the sealant.

Nitoseal PU40 sealant meets or exceeds the test Properties

requirements of:

ASTM C-920 Types S, Grade NS, Class 25, Use NT-A, Characteristic Result
Use M-A and Use 0-A. MAF: 25%
Sag
DIN EN ISO11600:2002 Type F 25LM (ASTM C639): Non sagging
Hardness Shore 'A'
(ASTM C661): 25 - 35
US Fed Spec TT-S-230a Type II
Application temperature: 5 - 50 oC
Service temperature range: -40 to 100oC
Effect of heat ageing
Description (ASTM C792): No cracking/chalking
Stain & colour change
Nitoseal PU40 sealant is a one component, moisture curing, (ASTM C510): No Stain
non-sag, gun-grade polyurethane elastomeric sealant. Tack Free Time : 18 minutes

It is designed to seal construction joints that are subject to

movement. After cure, Nitoseal PU40 forms a flexible Instruction for use
resilient rubber that has adhesion to a wide variety of
substrates. A tack-free skin is formed during the curing Preparation
process in 2 to 4 hours at normal conditions (23 oC). Cure
rates vary with changes in temperature and humidity. Ensure joint sides are square, clean and dry. Remove any
laitance, dirt or other contaminants by wire-brushing, grinding
or grit blasting.
Application
Priming
Insert sachet in to Fosroc Jumbo Gun. Cut end off sachet
and attach cap and nozzle and cut nozzle to desired bead Priming is not generally required. Highly absorbent substrate
size. Mask joint sides and insert a suitable backing rod if should be primed. Primer 7E should be used, these should
required. Extrude firmly into joint and tool off using a suitable be used as follows:
curved tool. Use only water (do not use detergent and
water). Primer 7E - For use on concrete, stone, brickwork, timber
and unglazed edges. One thin coat should be applied and
allow to dry for some time.

Page 1 of 2
Fosroc Nitoseal PU40
Estimating Precautions
Supply
Health and safety
Nitoseal PU40: 600 ml sachets
Primer 7E: 500 ml can Nitoseal PU40 may be harmful if swallowed or inhaled and
Fosroc Solvent 102: 4 litre can may cause skin and eye irritation. Product contains a very
small amount of isocyanates and low flash point solvent.
Guide to quantities
Should accidental skin contact occur, remove contaminated
Joint size Litres per Metre Metre run per
clothing and wash with warm soapy water. Do not scrub.
run 600ml sachet
6 x 10 0.06 10.00 If inhaled remove person to fresh air. Get medical advice if
12 x 10 0.12 5.00 breathing becomes difficult. In case of contact with eyes,
20 x 20 0.40 1.50 rinse immediately with plenty of clean water for at least 15
25 x 12 0.30 2.00 minutes and seek medical advice. If swallowed, give a glass
30 x 15 0.45 1.33 of water to dilute and seek medical attention immediately - do
not induce vomiting.
Storage For further information, refer to the appropriate Product
Material Safety Data Sheet.
Shelf life
12 months if stored in the original unopened sachets in a
Fire
cool dry place. Do not store in direct sunlight.
Nitoseal PU40 does not readily support flame. Prime 7E and
Limitations Solvent 102 is highly flammable liquid. Keep away from
sources of ignition. No smoking. Containers should be
Not recommended for the following: tightly sealed when not in use. In the event of fire, extinguish
with CO2 or foam. Do not use water jet.
 Unprimed joints that will be subjected to continuous water
immersion. Disposal

 Joints that are contaminated with grease, wax, corrosion, Dispose according to local authority regulations. Do not
bitumen or cement laitance. dispose down drains or into local waterways.

 Horizontal joints in floors or decks where traffic or abuse For further information on any of the above, please consult
is encountered. your local Fosroc office - as below.

 Special architectural finishes without proper testing.

Additional information
Application limitations:
Technical data - ancillary materials
 Nitoseal PU40 must not be applied to frost-bearing
Primer 7E
surfaces if temperature will be below freezing for more
than 24 hours. Flash point: 23oC
Density: 1.05 kg/litre
 Tooling techniques using solvents or soapy solutions are Coverage: 8 - 10 m2/litre
not recommended. Application
temperature: 5 to 50oC
 All surfaces must be evaluated for adhesion prior to Drying time: . 20 to 60 mins.
product acceptance. Flash point - Fosroc Solvent 102: 33oC
For further info please contact your local Fosroc office.

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation or information given by it.

Al Gurg Fosroc LLC

Post Box 657, Dubai telephone: fax: email:
United Arab Emirates (+9714) 2039699 (+9714) 2859649 agf@fosroc.com

www.fosroc.com Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai

UAE/0364/12/I