2015 Isuzu Truck 17.

PAGE
NPR HD, NQR, NRR Diesel Electrical Symbols

Symbol Meaning Symbol Meaning Symbol Meaning

Fuse Electronic Parts Coil (Inductor),
Solenoid Magnetic Valve

Fusible Link Resistor
Relay


Fusible Link Wire Speaker



Switch Buzzer Connector


Switch Circuit Breaker Light-Emitting Diode



Switch (Normal Close Type) Bulb Reed Switch



Contact Wiring Double-Filament Bulb Condenser



Battery Motor Horn



Diode Variable Resistor Rheostat Vacuum Switching Valve
2015 Isuzu Truck 17.2

PAGE
Abbreviations
Abbreviation Definition Abbreviation Definition
6A/T 6-speed automatic transmission IG Ignition
4A/T 4-speed automatic transmission kW Kilowatt
A/T Automatic transmission LH Left Hand
ABS Anti-lock brake system LWB Long Wheelbase
APP Accelerator pedal position M/T Manual Transmission
ATF Automatic transmission fluid M/V Magnetic valve
AUTO Automatic MAF Mass air flow
BRKT Bracket MIL Check engine light
C/B Circuit breaker OD Overdrive
CKP Crankshaft position OPT Option
CMP Camshaft position RWAL Rear Wheel Anti-lock Brake System
COMB Combination PTO Power Take Off
CONT Control RH Right Hand
D.R.L. Day time running light RR Rear
DC Direct Current SCV Suction control valve
ECM Electronic control module ST Start
ECT Engine coolant temperature STD Standard
ECU Electronic control unit SW Switch
EGR Exhaust gas recirculation SWB Short Wheelbase
EHCU Electronic and hydraulic control unit TCM Transmission Control Module
FL Fusible link V Volt
FRT Front VSV Vacuum Switching Valve
FT Fuel temperature W Watt (S)
H/L Headlight W/ With
HI High W/O Without
IAT Intake air temperature W/S Weld splice
IC Integrated circuit WOT Wide-open Throttle
LO Low

Figure 17.2.1
2015 Isuzu Truck 17.3

PAGE
Wiring
Wire Color

All wires have color-coded insulation. Wires belonging to a system’s main harness will have a single color. Wires belonging to a system’s
sub-circuits will have a colored stripe. Striped wires use the following code to show wire size and colors.

Example: 0.5 G / R

Red (Stripe Color)

Green (Base Color)

Wire Size (0.5 mm2)

Figure 17.3.1
2015 Isuzu Truck 17.4

PAGE
Abbreviations are used to indicate wire color within a circuit diagram. Refer to the following table.

Color-Coding Meaning Color-Coding Meaning

B Black BR Brown
W White LG Light Green
R Red GR Grey
G Green P Pink
Y Yellow LB Light Blue
L Blue V Violet
O Orange

Figure 17.4.1

Wire Size

The size of wire used in a circuit is determined by the amount of current (amperage), the length of the circuit, and the voltage drop allowed. The
following wire size and load capacity are specified by AWG (American Wire Gauge). (Nominal size means approximate cross sectional area.)

Figure 17.4.2
2015 Isuzu Truck 17.5

PAGE
Nominal Cross Sectional Outside Allowable AWG Size
Size Area (mm2) Diameter (mm) Current (A) (Cross reference)
0.3 0.372 1.8 9 22
0.5 0.563 2.0 12 20
0.85 0.885 2.2 16 18
1.25 1.287 2.5 21 16
2 2.091 2.9 28 14
3 3.296 3.6 37.5 12
5 5.227 4.4 53 10
8 7.952 5.5 67 8
15 13.36 7.0 75 6
20 20.61 8.2 97 4

Figure 17.5.1

Alternator Pulley Ratio NPR Diesel Engine

2.308 : 1 alternator pulley to crankshaft pulley

NPR-HD NQR NRR Diesel Engine

2.662 : 1 alternator pulley to crankshaft pulley

Additional information including complete chassis wiring schematics, connector locations, wire sizes, and pin connector diagrams can be obtained from our
service web site wwww.isuzutruckservice.com. There is a nominal fee for this service.
2015 Isuzu Truck 17.6

PAGE
Grounding Point Location

Figure 17.6.1 Figure 17.6.2

NOTICE: Abnormal phenomena of electrical components are considered resulted from defective grounding.
In repair, be sure to inspect grounding points and to tighten all fastening parts surrounding the grounding points
2015 Isuzu Truck 17.7

PAGE
Grounding Point Location

Figure 17.7.1 Figure 17.7.2

NOTICE: Abnormal phenomena of electrical components are considered resulted from defective grounding.
In repair, be sure to inspect grounding points and to tighten all fastening parts surrounding the grounding points
2015 Isuzu Truck 17.8

PAGE
(Vehicle Specifications Index Section – NPR-HD, NQR, NRR Diesel Electrical)

Grounding Point Location

Figure 17.8.1 Figure 17.8.2

NOTICE: Abnormal phenomena of electrical components are considered resulted from defective grounding.
In repair, be sure to inspect grounding points and to tighten all fastening parts surrounding the grounding points
2015 Isuzu Truck 17.9

PAGE
(Vehicle Specifications Index Section – NPR-HD, NQR, NRR Diesel Electrical)

Grounding Point Location

Figure 17.9.1 Figure 17.9.2

NOTICE: Abnormal phenomena of electrical components are considered resulted from defective grounding.
In repair, be sure to inspect grounding points and to tighten all fastening parts surrounding the grounding points
2015 Isuzu Truck 17.10

PAGE
Rear Body Lamp Switch
Rear Body Dome Lamp Switch is available as a: Port Installed Option IX2, Dealer Installed Option, and Body Company Installed Option.

Installation Procedure
PREPARATION
• Inspect and ensure all components are free from defects or damages.

Rear Body Dome Lamp Switch PROCEDURE

Part Number 8-98011-708-2 1) Remove dash cover. (Figure 1)

2) Remove top filler plug from

left side dash area. (Figure 2)

3) Insert - Rear Dome Lamp

Switch in top hole. (Figure 3)

4) Attach black connector

to switch. (Figure 4)

5) Ensure light illuminates

when pressed. Depress to
turn “OFF”. (Figure 5)

6) Re-install dash panel. (Figure 6)

7) Ensure that no scratches or

damage have been made to
dash panel.

Figure 17.10.1
2015 Isuzu Truck 17.11

PAGE
NPR HD, NQR, NRR Body Room Light, I.D. and Marker Lamp, Connector Location and Circuit Diagram (continued)

J-118 Rear Manufacture Connenctor-Connector End View

• 12010974
Connector Part Information
• 4-WAY M (BLK)

Pin Wire Color Circuit Function

Number
A LT GRN/ BLK BA48 Marker Light Voltage
B RED IA17 Power Source Voltage
C WHT/BLK IA28 Dome Light Voltage
D BLK IX13 Ground

Figure 17.11.1
Center Rear of the Last Crossmember

Packard Body Pulg Connector Parts

Chassis Housing ASM 1201-0974
Terminal 1208-9040
Terminal 1212-4587
Seal 1208-9679
Seal 1201-5193
Body Housing ASM 1201-5797
Housing 1201-5787
Connector Seal 1201-0492
Dummy Seal 1201-0300

Figure 17.11.2

Figure 17.11.3
2015 Isuzu Truck 17.12

PAGE
Fuse Location (interior)

Figure 17.12.1 Figure 17.12.2

2015 Isuzu Truck 17.13

PAGE
Relay Location (interior)

Figure 17.13.1

Figure 17.13.2
2015 Isuzu Truck 17.14

PAGE
Relay and Fuse Locations (exterior)

Figure 17.14.1

Figure 17.14.2
2015 Isuzu Truck 17.15

PAGE
Headlights Low Beam (AT)

Figure 17.15.1
2015 Isuzu Truck 17.16

PAGE
Headlights High Beam (AT)

Figure 17.16.1
2015 Isuzu Truck 17.17

PAGE
Tail lights (AT) Figure 17.17.2

The connectors that match the end

of frame tail and stop lamp harness
can now be ordered through
Isuzu dealers.

Chassis harness side

part number 897364-5300

Stop and tail lamp side

part number 897364-5310
Figure 17.17.1
Figure 17.17.3
2015 Isuzu Truck 17.18

PAGE
Roof Marker Lights (AT)

Figure 17.18.1
2015 Isuzu Truck 17.19

PAGE
Roof Clearance Lights (AT)

Figure 17.19.1
2015 Isuzu Truck 17.20

PAGE
Figure 17.20.1 Rear Turn Signal Lights (AT)
The connectors that match the end
of frame tail and stop lamp
harness can now be ordered through
Isuzu dealers.

Chassis harness side

part number 897364-5300

Stop and tail lamp side

part number 897364-5310

Figure 17.20.2 Figure 17.20.3

2015 Isuzu Truck 17.21

PAGE
Back Up Light Circuit (AT)

Figure 17.21.1
2015 Isuzu Truck 17.22

PAGE
J-111 Backup Alarm Connector End View Back up Alarm Circuit (AT)

Connector Part Information

Pin Wire Color Circuit Function

Color
1 RED/BLU KA23 Back Up Alarm Supply Voltage
2 BLK KX01 Ground
Left Inner Frame Rail, Behind the Last Crossmember

Figure 17.22.1
Back Up Alarm Connector
Chassis Side Connector
Housings 153000002 Housings 15300027
Terminal 12124977
Seal 12015899 Terminal 12084201
TPA 15300014
Matching Plug Seal 12015323
PED ASM 15300027
TPA 15300014
Figure 17.22.2
Figure 17.22.3

Figure 17.22.4 Figure 17.22.5

2015 Isuzu Truck 17.23

PAGE
Cigar Lighter Circuit (A/T)

Figure 17.23.1
2015 Isuzu Truck 17.24

PAGE
Radio Circuits

Figure 17.24.1
2015 Isuzu Truck 17.25

PAGE
(Vehicle Specifications Index Section – NPR-HD, NQR, NRR Diesel Electrical)

Auxiliary Power Source Circuit Diagram

Figure 17.25.1
2015 Isuzu Truck 17.26

PAGE
Trailer Connector Circuit Diagram

Figure 17.26.1
2015 Isuzu Truck 17.27

PAGE
Trailer Brake Circuit Diagram

Figure 17.27.1
2015 Isuzu Truck 17.28

PAGE
Model Year N-Diesel Trailer Brake Controller Wiring and Activation
and Trailer Wiring Connector
Introduction:
Begining with the 2011 Model Year NPR ECO-MAX, NPR-HD, NQR, and NRR feature integrated electronic trailer brake controller wiring and a dedicated chassis
wiring
harness for control of trailer stop, turn, and tail lamps. Note: the electronic brake controller is not supplied with the vehicle.

Integrated Electronic Brake Controller Wiring and Activation:

Wires for the electronic trailer brake controller are located behind the radio. To access these wire, remove the radio and DIN pocket from the dash, and pull out
the wiring pigtail for the trailer brake controller.

Figure 17.28.1 Figure 17.28.2

Wire Chart for the brake controller pigtail:

Wire# Wire Size Wire Size Description/Notes

Wire Color
(mm2) (AWG Approx)

Supply power for brake controller

1 Red/Green 3 12 (Fused to battery 20A; continuous max)

Output signal from brake controller

2 Red 3 12 (rated max 20A continuous)
Brake lamp signal (12V on when brake
3 Red 0.85 18 applied. Activated by relay R-9)

4 Black 0.85 18 Ground (max continuous current 10A)

The brake signal wire (Wire # 3) is activated by installation of a relay in the “R-9” position in
the center relay console located in the center of the dash just above floor level.

Figure 17.28.3
2015 Isuzu Truck 17.29

PAGE
The R9 relay (P/N 8-97173-037-1) is not supplied with the vehicle. The relay can be ordered from your Authorized Isuzu Dealer’s parts Department.
R-9 relay position:

Figure 17.29.1
The power supply for the trailer brake controller (Wire #1) is not energized from the factory.
To power the brake controller, the brake controller harness power supply must be plugged in to the chassis power supply plug.

1) Locate the trailer brake controller power supply

harness under the cab, behind the passenger-side
head light:

2) Remove tape to expose the 2 connectors. The Grey

connector is used to supply power to the trailer
brake controller (Wire #1). This connector plugs in
to the chassis trailer brake controller power supply.
The Black connector is the output signal wire from
the trailer brake controller (Wire #2).
Figure 17.29.2
2015 Isuzu Truck 17.30

PAGE
3) Unplug the harness. Connect the Black connector
(Wire #2) to an extension wire of suitable length and
route the wire to the rear of the vehicle. This wire is
the trailer brake controller output signal wire.

Figure 17.30.1
4) Remove the tape from the wire with the Grey connector (Wire #1) and route this wire underneath of the right hand frame rail.

Figure 17.30.2 Figure 17.30.3

2015 Isuzu Truck 17.31

PAGE
5) Locate the chassis side power supply harness.
This connector is located just inboard of the right
hand frame rail, beneath the ABS control module.

Figure 17.31.1

6) Remove tape and route chassis side power supply

wire to brake controller power supply wire:

Figure 17.31.2
2015 Isuzu Truck 17.32

PAGE
7) Remove protective cover, and plug chassis side
power supply harness into electronic trailer brake
controller power supply connector (Wire #1).
Secure harness to chassis with suitable tie strap.

Figure 17.32.1

Trailer Wiring Connector

There is a wiring harness that allows upfitter to con-

trol trailer lighting functions without having to splice
into the vehicle tail lamp harness. The connector is
located on the left hand frame rail (driver’s side), to
the rear of the transmission cross member. This con-
nector is illustrated on the following page.
The connector wires are the standard 4 wire electri-
cal light system that is used on the chassis (separate
stop and turn light).
If the trailer has a 3 wire electrical system (combined
stop and turn light ) a heavy duty tail light converter
box will be necessary for proper trailer light integra-
tion.

Figure 17.32.2
2015 Isuzu Truck 17.33

PAGE
Page 1 of 2

Trailer Connector diagram:

Connectors and Components
Connectors and Componets
H-172 Front Chassis Harness to Towing Converter
H-172 Front Chassis Harness to Towing Converter
Pag

• 8-Way F (BLK • R020054

Connector Part Connector Part
• Upfitter • 8-Way M (BLK)
Information Information
Connector

Wire Circuit Circuit

Pin Function Pin Wire Color Function
Color No. No.

Stop Lamp
1 1 GRN MF02
Voltage

Tail Lamp
2 2 GRN/RED BA04
Voltage
Left Turn
3 3 GRN/BLK MF04 Signal
Voltage
Right Turn
4 4 GRN/WHT MF05 signal
Voltage
5 5 BLK MU01 Ground Figure 17.33.2
6 6 - - Not Used
7 7 - - Not Used
Fuse FL-16
8 8 RED/WHT MF01 Supply
Power

Left
LeftInner Sideofofthe
Inner Side the Frame
Frame Rail,
Rail, Behind
Behind the Transmission
the Transmission Crossmember
Crossmember

Figure 17.33.1
2015 Isuzu Truck 17.34

PAGE
(Vehicle Specifications Index Section – NPR-HD, NQR, NRR Diesel Electrical)

Fuel Tank Sending Unit Resistance (In-Frame Tank & Side Frame Tank)

Fuel Tank Sending Unit Resistance (In-Frame Tank) Fuel Tank Sending Unit Resistance (Side Frame Tank)

Figure 17.34.1 Figure 17.34.2