®

SW- SUZUKI -L0 (SDD/SBB)

CODE: D431404XA - VERS. 3.0

GB
 INDEX

1 SUZUKI® FUNCTIONS MENU .................................................. 3

U

1.1 PROGRAMMING KEYS a .................................................................... 5

1.2 PROGRAMMING KEYS B.................................................................... 7
1.2.1 ADDING NEW KEYS ...................................................................... 8
1.2.2 ADDING OLD KEYS ..................................................................... 10
1.2.3 ERASING ALL KEYS.................................................................... 12
1.3 PROGRAMMING C KEYS ................................................................. 14
1.4 READ ERRORS ................................................................................. 17
1.5 ERASE ERRORS ............................................................................... 18
1.6 IMMO ID READING............................................................................ 18
1.7 READING NUMBER OF MEMORIZED KEYS ................................... 19

2
1 SUZUKI® FUNCTIONS MENU

ILCO KEY Position Immobil.

MODEL From To Silca REF Transponder ID OBP
REF # OBD Type

SUZUKI
ALTO 1996 SZ11RT4 TEXAS 4C 4 C13 A
ALTO 1996 SZ12T4 TEXAS 4C 4 C13 A
BALENO 1996 SZ11RT4 TEXAS 4C 4 C13 A
BALENO 1996 SZ12T4 TEXAS 4C 4 C13 A
GRAND VITARA 1996 2002 SZ11RT4 TEXAS 4C 4 C13 A
GRAND VITARA 1996 2002 SZ12T4 TEXAS 4C 4 C13 A
GRAND VITARA 2002 PH / CR 46 4 C13 A
IGNIS 2000 TEX / CR 4D 4 C13 A
IGNIS [D] 2000 TEX / CR 4D 5 C13 B
JIMNY 1999 2002 SZ11RT4 TEXAS 4C 4 C13 A
JIMNY 2002 TEX / CR 4D 4 C13 A
LIANA 2001 TEX / CR 4D 4 C13 A
SWIFT 1996 2005 SZ11RT4 TEXAS 4C 4 C13 A
SWIFT 1996 2005 SZ12T4 TEXAS 4C 4 C13 A
SWIFT 2005 PH / CR 46 4 C13 C
SWIFT [D] 2005 PH / CR 46 4 C13 B
VITARA 1996 2002 SZ11RT4 TEXAS 4C 4 C13 A
VITARA 1996 2002 SZ12T4 TEXAS 4C 4 C13 A
VITARA 2002 PH / CR 46 4 C13 A
WAGON R 1998 2000 SZ11RT4 TEXAS 4C 4 C13 A
WAGON R 2000 HU87RT17 PH / CR 40 4 C13 A
WAGON R[D] 1998 2000 SZ11RT4 TEXAS 4C 5 C13 B
WAGON R[D] 2000 HU87RT12 PH / CR 40 5 C13 B

The functions on these vehicles are:

- Programme new keys (max 4 keys in the memory);
- Read IMMO ID;
- Read the errors present;
- Delete all errors.
- Read the number of keys memorized

3
 To make use of this function, use:

SWITCH ADAPTER

CABLE OBD II [STANDARD]

Immobilizer Immobilizer
Type A – Type B Type C
New/s key/s All keys
(Max. 4) (Max. 4)

SBB CABLE/ADAPTER

CABLE OBD II [00] (STANDARD)

WHERE TO FIND THE PLUG DIAGNOSTICS

C13

4
 GENERAL INFORMATION: Suzuki immobilizer systems have idle times of approximately 2
minutes between the programming operations or between one ignition and another. The
SDD/SBB must therefore be disconnected for 2 minutes between one programming operation
and another or between one ignition and another.

SELECTING THE CAR MAKE

In this case SDD/SBB is able to recognize automatically the various central units connected and
therefore use the right communication procedure.
Simply identify:
- CAR MODEL
- YEAR OF MANUFACTURE
- SUZUKI -
ALTO (96-02)
BALENO (96- )
IGNIS (00- )
> JIMNY (99-02)

- Use the arrow keys to select the make, then press ENTER.
- Press ESC to quit.

TYPE A IMMOBILIZER FUNCTIONS MENU (56)

This section is used to carry out the functions provided, in particular:
- programme new keys in the immobilizer also when all the original keys are missing;
- erase from the memory the code of one or more missing keys;
- check how many keys have been memorized;
ATTENTION: the programming system for TYPE A SUZUKI is structured so that keys can be added
individually in the vehicle.
®
The SUZUKI functions menu is structured as follows:

- SUZUKI -
> PROG. NEW KEYS
ERASE ALL KEYS
No. KEYS MEM.

- Select and press ENTER.

1.1 PROGRAMMING KEYS A

This function is used to add keys to the immobilizer. The system can store up to a total of 4
keys; if 4 keys are already stored in the memory, new ones cannot be added.
- To activate the function, select “PROGRAMM.KEYS” and press ENTER:
The display will show:
Insert key to be
programmed.
Turn ignition on

Press any key...

- Insert the new key to be programmed into the ignition unit

- Turn the key to ON
- Press any key to continue

5
 If errors occur during communication, the display will show msg [ERROR 04 or ERROR 05] (see
Ch. ERROR MESSAGES” in the User’s Manual); if not the display will show:
Key programmed
Programme other keys?

The key has been programmed successfully.

- Press ENTER to continue with programming another key (max. 4).
- Press ESC to quit.

KEY TESTING
ATTENTION: to check whether the memorized keys work, do an ignition test on the vehicle; if the
result is negative, repeat the operation.

ARCHIVING OPERATIONS – USER DATA

At the end of the programming the display will show:

File data for this

operation?

NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the IMMOBILIZER functions menu screen.
- Yes, to memorize the data for the operation just completed.
- Select ESC to quit.

USER DATA ARCHIVE

To enter the user data the display will show:

- USER DATA -
POS.: 001
DATE: 19/07/01
> SURNAME: XXXXXXXXXX
NAME: XXXXXXXXXX
No.PLATE:XXXXXXXXXX

- SURNAME (required) (12 characters)

- NAME / NUMBER PLATE (Optional) (12 characters)

The following data will be saved automatically:

- POS.: Location where the data will be saved
- DATE: Date of the operation
- MAKE: Make of the vehicle for which the operation was performed
- MODEL: Model of the vehicle for which the operation was performed
- YEAR: of the model
- Keys Mem.: number of keys stored in memory
- PIN CODE: (if storage is confirmed by the operator)
- IMMO ID: Immobilizer ID, V.I.N., Mechanical code (on certain models only)

6
 To enter data:
- Use the keys to position the pointer on the required item;
- Press to enter and select the field in which to insert text;
- Press ENTER to confirm;
- Select ESC to quit and memorize the data.

Are the data entered

correct?
NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the data entry window.
- Yes, to store the data in the file.

TYPE B IMMOBILIZER FUNCTIONS MENU (47)

This section is used to carry out the functions provided, in particular to:
- programme new keys in the immobilizer also when all the original keys are missing;
- erase from the memory the code for one or more missing keys;
- check how many keys are in the memory;
- view immobilizer identification (IMMO ID), V.I.N. and mechanical code (only on certain
models);
- erase any anomalies found in the immobilizer memory.
®
ATTENTION: the structure of the programming system for SUZUKI TYPE B allows keys to be added
individually in the vehicle.

®
The structure of the SUZUKI TYPE B functions menu is as follows:
- SUZUKI -
> KEY PROGRAMMING
PRESENT ERRORS
ERROR RESET
IMMO ID READING

- Select and press ENTER.

1.2 PROGRAMMING KEYS B

This function is used to add keys to the immobilizer.
Is not possible to erase keys individually on the vehicle.
- To activate the function, select "PROGRAMM.KEYS" and press ENTER:

- KEY PROGRAM. (B) -

> ADD NEW KEYS
ADD OLD KEYS
ERASE ALL KEYS

7
1.2.1 ADDING NEW KEYS
This function is used to add a key that has never been programmed in the immobilizer.
- Select "ADD NEW KEYS" and press ENTER; the display will show:

- ADD NEW KEY -

STORE KEY

>NO
YES

- Select YES/NO and press ENTER.

- No, to return to the previous menu;
- Yes, to programme the new key.

The display will show:

Turn ignition off!

Turn the key to the OFF position.

PROGRAMMING THE KEY

The display will show:

INSERT THE NEW KEY

TURN IGNITION ON!

Please wait

- Enter the new key to be programmed and turn it to the ON position; after a few seconds
the display will show:

Turn ignition off!

Press any key...

- Turn the NEW key to the OFF position.

- Press any key to continue.

8
 The display will show:
Turn ignition on!

Please wait

- Turn the NEW key to the ON position.

Programming of the key on the vehicle then starts.
- After a few seconds the display will show:

The key has been

stored

Press any key

- Press a key

The display will show:

Another key to
store?

>YES
NO

- Select YES/NO, then press ENTER.

- No, to store the user data in the archive.
- Yes, to programme a new key.
At the end of the operation the display will show:

Extract the
programmed key

Press any key

- Press a key to store the user data in the archive.

-

TESTING KEYS
ATTENTION: to check that the programmed keys work properly, carry out an ignition test on the car.
If necessary repeat the operation.

9
1.2.2 ADDING OLD KEYS
This function is used to add a key that was previously erased in the immobilizer.
- Select "ADD OLD KEY" and press ENTER; the display will show:

- ADD OLD KEY -

KEY STORING

>NO
YES

- Select YES/NO and press ENTER.

- No, to return to the previous menu;
- Yes, to programme the new key. The display will show:
Turn ignition off!

- Turn the key to the OFF position; the display will show:

PROGRAMMING A KEY
The display will show:
INSERT THE NEW KEY
TURN IGNITION ON!

Please wait

- Enter the "OLD" key to be programmed and turn to the ON position; the display will
show:
Turn ignition off!

Please wait

- Turn the "OLD" key to the OFF position; the display will show:

Turn ignition on!

Please wait

10
- Turn the "OLD" key to the ON position.
The key is then programmed in the vehicle.
After a few seconds the display will show:

The key has been

stored

Press any key

- Press a key.
The display will show:
Another key to
store?

>YES
NO

- Select YES/NO, then press ENTER.

- No, to store the user data in the archive
- Yes, to store the "OLD" key in the memory again.
At the end of the operation the display will show:

Extract the
programmed key

Press any key

- Press a key to store the user data in the archive.

ARCHIVING OPERATIONS - USER DATA

At the end of the memorizing operations the following message will appear:

Do you want to save

the customer data?

NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the IMMOBILIZER function menu.
- Yes, to memorize the data relating to the operation completed.
- Select ESC to quit.

11
 USER DATA ARCHIVE
To enter the user data the display will show:

- USER DATA -
POS.: 001
DATE: 19/07/01
> SURNAME: XXXXXXXXXX
NAME: XXXXXXXXXX
REG.NO: XXXXXXXXXX

- SURNAME (required) (12 characters).

- NAME / NUMBER PLATE (optional) (12 characters).
The following data will be saved automatically:
- POS.: Location where the data will be saved
- DATE: Operation date
- MAKE: Make of the vehicle for which the operation was performed
- MODEL: Model of the vehicle for which the operation was performed
- YEAR Model year
- Keys Mem.: Number of keys stored in memory
- PIN CODE: (if storage is confirmed by an operator)
- IMMO ID: Immobilizer control unit ID
To enter the data:
- Use the keys to position on the desired item.
- Press to enter and select the field where the text is to be typed.
- Press ENTER to confirm.
- To quit and memorize the data, press ESC.

Is the information
inserted correct?
NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the data entry window.
- Yes, to store the data in the file.

1.2.3 ERASING ALL KEYS

This function is used to erase all the keys stored in the immobilizer memory; to continue enter
the PIN CODE.
- "ERASE ALL KEYS" from the “PROGRAMM. KEYS” menu and press ENTER.
The display will show:
- ERASE ALL KEYS -
All keys will be
erased.

Go on?
YES
>NO

- Select and press ENTER.

- No, to return to the previous menu.
- Yes, to erase all the keys stored in the immobilizer memory.
- Select ESC to quit.

12
The display will show:
Turn the key
in OFF position

Press any key...

- Turn the key to the OFF position and press any key.
Deletion of all the keys then takes place.
After a few seconds (10"-40") the display will show:

All keys
have been
erased

- Deletion terminated.
After a few seconds the display will show:

Turn ignition on!

Press any key...

- Turn the key to the ON position and press a key.

13
 TYPE C IMMOBILIZER FUNCTIONS MENU (60)
In this section you can carry out the functions provided, particularly:
- programme new keys in the immobilizer even if all the original keys are missing;
- check how many keys are in the memory;
ATTENZIONE: the programming system for SUZUKI® TYPE C, is structured so that keys CANNOT be
added individually. At each programming session all the keys that are to be used on the
vehicle must be re-programmed.
The functions menu for SUZUKI® is structured as follows:

- SUZUKI -
> PROG. NEW KEYS
No. KEYS MEM.

Select and press ENTER.

1.3 PROGRAMMING C KEYS

This function is used to add keys to the immobilizer. The system can memorize up to a total of 4
keys. If the system has already memorized 4 keys, new ones cannot be added.
- To activate the function, select “PROGRAMME KEYS” and press ENTER:
The display will show:
Please wait
connecting…

If errors occur during communication, the display will show msg [ERROR 04 or ERROR 05] (see
Ch. ERROR MESSAGES” in the User’s Manual) otherwise the display will show:
Key programmed

Programme other keys?

The key has been programmed successfully.

14
 Press ENTER to programme another key (max. 4).
- Press ESC to quit.

Insert key to be
programmed.

Turn ignition on

Press any key…

- Insert a new key to be programmed.
- Turn the key to the ON position.
- Press any key.
If errors occur during communication, the display will show msg [ERROR 04 or ERROR 05] (see
Ch. WARNING/ERROR MESSAGES” in the User’s Manual) otherwise the display will show:
Key programmed

Programme other keys?

The key has been programmed successfully.

- Press ENTER to programme another key (max. 4).
- Press ESC to quit.

KEY TEST
ATTENTION: to check that the memorized keys work properly, disconnect SDD/SBB and turn the
ignition for the vehicle with all the programmed keys. Wait 30 seconds between keys and
if one or more of the keys does not start the vehicle, repeat the operation for
programming new keys.

ARCHIVING OPERATIONS - USER DATA

At the end of the memorizing operations the following message will appear:

Do you want to save

the customer data?

NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the IMMOBILIZER function menu.
- Yes, to memorize the data relating to the operation completed.
- Select ESC to quit.

15
 USER DATA ARCHIVE
To enter the user data the display will show:

- USER DATA -
POS.: 001
DATE: 19/07/01
> SURNAME: XXXXXXXXXX
NAME: XXXXXXXXXX
REG.NO: XXXXXXXXXX

- SURNAME (required) (12 characters).

- NAME / NUMBER PLATE (optional) (12 characters).
The following data will be saved automatically:
- POS.: Location where the data will be saved
- DATE: Operation date
- MAKE: Make of the vehicle for which the operation was performed
- MODEL: Model of the vehicle for which the operation was performed
- YEAR Model year
- Keys Mem.: Number of keys stored in memory
- PIN CODE: (if storage is confirmed by an operator)
- IMMO ID: Immobilizer control unit ID
To enter the data:
- Use the keys to position on the desired item.
- Press to enter and select the field where the text is to be typed.
- Press ENTER to confirm.
- To quit and memorize the data, press ESC.

Is the information
inserted correct?
NO
>YES

- Select YES/NO and press ENTER.

- No, to return to the data entry window.
- Yes, to store the data in the file.

16
1.4 READ ERRORS
This function is used to check for any anomalies memorized in the immobilizer.
- Select the item "READ ERRORS" and press ENTER; the display will show:

Please wait:
present errors

NO ERRORS
If there are no anomalies in the memory, the display will show:

- ERROR READING -

NO ERROR
DETECTED

Press any key...

ERRORS FOUND
If there are anomalies in the memory, the display will show:

- ERROR READING -

Detected
XX
errors

Press any key...

The display will show how many errors (XX) there are in the immobilizer memory:

- Press any key to see:

ERR.: XXXXXXXXXXX 1/X

Description
of the error

- ERR: XXXXXXXXXXXX code for error found,

- Press  to scroll all the errors found in sequence.
- Press ESC to return to the previous menu.

17
1.5 ERASE ERRORS
- Select “ERASE ERRORS” and press ENTER, the display will show:

ERASE ERRORS
Erase
present errors:
>NO
YES

- Select and press ENTER.

- No, to return to the previous menu.
- Yes, to erase the errors in the memory.
- Select ESC to quit.
The display will show the message:

ERASING

TERMINATED

Press ESC to quit

- Select ESC to return to the main menu.

1.6 IMMO ID READING

This function is used to view immobilizer identification (ID IMMO.), a code comprising
alphanumerical characters.
- Select and press ENTER; the display will show:

- IMMO ID READING -
XX XXXXXXXX XXXX XXXX
XXXX

KEY NUMBER:

The immobilizer identification (IMMO ID) is shown

- KEY NUMBER: mechanical key code (info. available only on certain models).
- Press to continue.
- IDENTIFIER -
VIN: XXXXXXXXXXXXXXXX

Press ESC to quit

The following data are shown on this screen:
- VIN: Vehicle Identification Number.
- Press ESC to quit.

18
1.7 READING NUMBER OF MEMORIZED KEYS
This function is used to view the number of keys memorized in the vehicle.
- In the menu select the function “No. KEYS MEM” and press ENTER, the display will show:

- No. KEYS MEM. -

Keys number
in memory :
XX

Press any key...

Press any key.

19
 SILCA S.p.A.
Via Podgora, 20 (Z.I.)
31029 VITTORIO VENETO (TV)
Tel. 0438 9136 Fax 0438 913800
www.silca.it

In the United Kingdom

SILCA Ltd.
Kimpton Road - Sutton
SURREY SM3 9QP
Tel. 0208 6416515
Fax 0208 6441181
E-mail: sales@silcaltd.co.uk

In Germany
SILCA GmbH
Siemensstrasse, 33
42551 VELBERT
Tel. 02051 2710
Fax 02051 271172
E-mail: info@silca.de

In France
SILCA S.A.
78440 PORCHEVILLE
Tel. 01 30983500
Fax 01 30983501
E-mail: info@silca.fr

In Spain
SILCA KEY SYSTEMS S.A.
C/Santander 73A
BARCELONA - SPAIN
Tel. 0034 934981400
Fax 0034 932788004
E-mail: silca@silca.es

Members of the Kaba Group