MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

FLANGES & GASKETS

Most of the flanges have intelligent custom properties built into their design tables (making extensive use of the concatenate function) to populate your Bills of Materials (example below).
ITEM No. 1 QTY. 1 DESCRIPTION FLANGE RFWN - DN100 300# Sch 80 SIZE DN100mm 300# Sch 80 MATERIAL A-105 MASS (kg) 11.9

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a flange with different material properties, etc. ANSI RF WN A105 Contains over 500 configurations with sizes ranging from DN15 to 600, ratings from 150 to 2500# and the full range of wall thicknesses. ANSI RF WN S/S 304H Contains over 500 configurations with sizes ranging from DN15 to 600, ratings from 150 to 2500# and the full range of wall thicknesses. DIN RF SOW - STEEL Configurations from DN15 to DN300, ratings from PN16 to PN40.

STUB END DIN - STEEL Configurations from DN32 to DN250

FLANGE FOR STUB END DIN - GAL Configurations from DN32 to DN250

1 of 28

MAKO ENGINEERINGS PIPING LIBRARY

GASKET SEF DIN (for Stub End Flange) Configurations from DN32 to DN250 - 1.5 & 3mm thick. STUB END FLANGE SET DIN STEEL / GAL Configurations from DN32 to DN250 Made up of the above 2 components, plus gasket, nuts & bolts. DIN RF THREADED - GALVANISED Configurations from DN6 to DN150, ratings from PN6 to PN100 (DIN 2565 to 2568). DIN RF THREADED - STEEL Configurations from DN6 to DN150, ratings from PN6 to PN100 (DIN 2565 to 2568). ANSI RF BLIND A105 Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

Revision: C Date of issue: 12 February 2004

ANSI RF BLIND 316 Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

ANSI RF BLIND 316L Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

ANSI RF SOW A105 Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

2 of 28

MAKO ENGINEERINGS PIPING LIBRARY

ANSI RF SOW 316L Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

Revision: C Date of issue: 12 February 2004

ANSI RF SOW 316 Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

ANSI RF SOW 304 Configurations from DN15 to DN600, ratings of 150#, 300# & 600#

ANSI RF SOW 304L Configurations from DN15 to DN600, ratings of 150#, 300# & 600# GASKET, FULL FACE ANSI (RUBBER) Configurations from DN15 to DN600, ratings of 150# & 300# - 1.5 & 3.0mm thick (gasket shown in uncompressed state). Details per Klinger Catalogue. GASKET, FULL FACE ANSI Configurations from DN15 to DN600, ratings of 150# & 300# - 1.5 & 3.0mm thick (gasket shown in uncompressed state). Details per Klinger Catalogue. GASKET, RING ANSI Configurations from DN15 to DN600, - 1.5 & 3.0mm thick (gasket shown in uncompressed state). Details per Klinger Catalogue. GASKET, SPIRAL WOUND ANSI (S/S 304) 300+ Configurations from DN15 to DN600, ratings of 150# & 300# - 3.2, 4.4, 6.4 & 7.2mm thick (gasket shown in uncompressed state) CRIR & CR configs. Details per Klinger Catalogue. 3 of 28

MAKO ENGINEERINGS PIPING LIBRARY

GASKET, SPIRAL WOUND ANSI (S/S 316) 300+ Configurations from DN15 to DN600, ratings of 150# & 300# - 3.2, 4.4, 6.4 & 7.2 thick (gasket shown in uncompressed state) CRIR & CR configs. Details per Klinger Catalogue. AS2129 FF BLIND STEEL GR 250 Configurations from DN15 to DN600 in ratings of Table D, Table E, Table F & Table H.

Revision: C Date of issue: 12 February 2004

AS 2129 FF SOW STEEL GR 250 Configurations from DN15 to DN600 in ratings of Table D, Table E, Table F & Table H. GASKET, FULL FACE AS2129 Configurations from DN15 to DN600 in ratings of Table D, Table E, Table F & Table H 1.5 & 3.0mm thick. Details per Klinger Catalogue. INNER FLANGE CuNiFe DIN 86037 (CuNi10Fe1,6Mn) uses loose flange DIN 86037 Configurations from 20 OD to 914 OD. Details per Eucaro Catalogue. www.eucaro.de LOOSE FLANGE GAL DIN 86037 Use with inner flange DIN 86037 Configurations from 20 OD to 914 OD in ratings of PN16 & 10. Details per Eucaro Catalogue. www.eucaro.de INNER FLANGE CuNiFe VG 85387 (CuNi10Fe1,6Mn) uses loose flange VG 85387 Configurations from 38 OD to 133 OD. Details per Eucaro Catalogue. www.eucaro.de

4 of 28

MAKO ENGINEERINGS PIPING LIBRARY

LOOSE FLANGE VG 85387 (GAL & G-CuSn10) Use with inner flange VG 85387 Configurations from 38 OD to 133 OD in ratings of PN25 & 10. Details per Eucaro Catalogue. www.eucaro.de INNER FLANGE CuNiFe VG 85356 (CuNi10Fe1,6Mn) uses loose flange VG 85356 Configurations from 25 OD to 324 OD. Details per Eucaro Catalogue. www.eucaro.de LOOSE FLANGE VG 85356 (GAL & G-CuSn10) Use with inner flange VG 85356 Configurations from 25 OD to 324 OD in ratings of PN25, 16 & 10. Details per Eucaro Catalogue. www.eucaro.de DIN 86033 SOW CuNiFe (CuNi10Fe1,6Mn) Configurations from 16 OD to 108 OD in ratings of PN16/10. Details per Eucaro Catalogue. www.eucaro.de

Revision: C Date of issue: 12 February 2004

5 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

PIPES
All pipes have intelligent custom properties built into their design tables (making extensive use of the concatenate function) to populate your Bills of Materials (example below).
ITEM QTY Part No. 1 1 150mm, Schedule 40 DESCRIPTION PIPE - 150NS, SCH 40 CUT LENGTH 750mm SIZE MATERIAL ASTM A106

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a fitting with different material properties, etc. PIPE A106 DN 6 TO DN 900 SCH 10 to SCH 160 & STD to XXXS (WT per availability). PIPE A53 DN 6 TO DN 900 SCH 10 to SCH 160 & STD to XXXS (WT per availability).

PIPE API 5L DN 6 TO DN 900 SCH 10 to SCH 160 & STD to XXXS (WT per availability).

LINEPIPE DN 6 TO DN 900 SCH 10 to SCH 160 & STD to XXXS (WT per availability).

PIPE 304H To DN 300

6 of 28

MAKO ENGINEERINGS PIPING LIBRARY

PIPE DIN 2458 (ERW) DN 6 TO DN 300

Revision: C Date of issue: 12 February 2004

PIPE CuNi10Fe1.6Mn DIN 86019 (seamless) 8 OD TO 419 OD, WT from 1.0 to 10mm. Modelled from Eucaro catalogue www.eucaro.de PIPE CuNi10Fe1.6Mn DIN 86018 (welded) 324 OD TO 1620 OD, WT from 4.0 to 10mm. Modelled from Eucaro catalogue www.eucaro.de

7 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

BUTT WELD FITTINGS

All butt weld fittings have intelligent custom properties built into their design tables (making extensive use of the concatenate & VLookup functions) to populate your Bills of Materials (example below).
ITEM 1 2 3 QTY 1 1 1 DESCRIPTION FLANGE - 100 nb RFSO ANSI 150# CONCENTRIC REDUCER - DN100 x 80 SCH. 40 ELBOW 90 deg LRBW 100NS Sch 40 SIZE 100 nb-150# DN100x80 SCH. 40 100NS Sch 40 MATERIAL ASME B16.5 - A105 A-234 WPB A-234 WPB Kg EA 5.3 1.4 3.8

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a fitting with different material properties, etc. These butt weld fittings have the CPoints offset to create a 2mm weld gap. Should your companys standard require a different gap it is a simple amendment on each of the models. ELBOW- LONG RADIUS(1.5D) - DIN STEEL (45 & 90 DEG.) Configurations DN25 to DN200 in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. ELBOW SHORT RADIUS (1D) DIN STEEL (45 & 90 DEG) Configurations DN25 to DN200 in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. ELBOW- LONG RADIUS(1.5D) - DIN 86090 CuNi10Fe1,6Mn (30, 45, 60 & 90 DEG.) Configurations 20 OD to 914 OD in angles of 30, 45, 60 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. Per Eucaro catalogue www.eucaro.de ELBOW- SHORT RADIUS(1D) EHN 9603/600 CuNi10Fe1,6Mn (30, 45, 60 & 90 DEG.) Configurations 20 OD to 914 OD in angles of 30, 45, 60 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. Per Eucaro catalogue www.eucaro.de 8 of 28

MAKO ENGINEERINGS PIPING LIBRARY

ELBOW LONG RADIUS (1.5D) ANSI A234 ( 45 & 90 DEG). 430 configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability) in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. ELBOW SHORT RADIUS (1D) ANSI A234 (45 & 90 DEG). 420 configurations DN20 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability) in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. ELBOW LRBW ANSI SS304# DN15 to DN300 SCH 5S to 80S (WT per availability).

Revision: C Date of issue: 12 February 2004

ELBOW 3D ANSI A234 (45 & 90 DEG). 430 configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability) in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. ELBOW 5D ANSI A234 (45 & 90 DEG). 430 configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability) in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow.. CONCENTRIC REDUCER A234 DN20 x 15 to DN900 x 850 (950 configs) SCH 10 to 160 & STD to XXS (WT per availability).

ECCENTRIC REDUCER A234 DN20 x 15 to DN900 x 850 (950 configs) SCH 10 to 160 & STD to XXS (WT per availability).

9 of 28

MAKO ENGINEERINGS PIPING LIBRARY

CONCENTRIC REDUCER DIN - STEEL DN20 x 16 to DN300 x 250, limited wall thicknesses.

Revision: C Date of issue: 12 February 2004

CONCENTRIC REDUCER DIN 86089CuNi10Fe1,6Mn (SMLS) 20 x 16 OD to 368 x 324 OD, all pipe wall thicknesses (seamless only). Per Eucaro catalogue www.eucaro.de CONCENTRIC REDUCER 419 to 914 - DIN 86089CuNi10Fe1,6Mn (WELDED) 419 x 194 OD to 914 x 813 OD, all pipe wall thicknesses (welded only). Per Eucaro catalogue www.eucaro.de ECCCENTRIC REDUCER EHN 9603/440CuNi10Fe1,6Mn (SMLS) 20 x 16 OD to 457 x 419 OD, all pipe wall thicknesses. Per Eucaro catalogue www.eucaro.de ECCENTRIC REDUCER 508 to 914 EHN9603/450- CuNi10Fe1,6Mn (WELDED) 508 x 267 OD to 914 x 813 OD, all pipe wall thicknesses. Per Eucaro catalogue www.eucaro.de EQUAL TEE A234 DN20 to DN900 (except DN650, 700, 800 & 850) SCH 10 to 160 & STD to XXS (WT per availability). Per Tubemakers Techniref 1994

10 of 28

MAKO ENGINEERINGS PIPING LIBRARY

REDUCING TEE A234 (ANSI 16.9) DN20 x 15 to DN900 x 750 (except DN650, 700, 800 & 850) SCH 10 to 160 & STD to XXS (WT per availability). Per Tubemakers Techniref 1994 EQUAL TEE DIN STEEL DN20 to DN300, limited wall thicknesses.

Revision: C Date of issue: 12 February 2004

REDUCING TEE DIN STEEL DN20 x 16 to DN300 x 250, limited wall thicknesses.

EQUAL TEE DIN & EHN CuNi10Fe1,6Mn 20 OD to 914 OD, all pipe wall thicknesses (seamless & welded). Per Eucaro catalogue www.eucaro.de REDUCING TEE DIN & EHN CuNi10Fe1,6Mn 25 x 20 OD to 914 x 813 OD, all pipe wall thicknesses (seamless & welded). Per Eucaro catalogue www.eucaro.de END CAP- 15 to 150NB A-234 DN15 to DN150 Sch 40, to 160 & STD, to XXS (WT per availability).

END CAP 200-900 - SE A-234 DN200 to DN900 Sch 10 to 160 & STD TO XXS (WT per availability).

11 of 28

MAKO ENGINEERINGS PIPING LIBRARY

END CAP DIN 28011 CuNi10Fe1,6Mn 30 OD to 914 OD, all pipe wall thicknesses (seamless & welded). Per Eucaro catalogue www.eucaro.de BEND 180 DEG LONG RADIUS (1.5D) - A-234 200+ configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability). Note that SW cannot handle elbows greater than 90 degrees; therefore these bends have to be inserted as a fitting at the end of the route, then RMB on CPoint 2 and add to route (as per an eccentric reducer in the piping help). BEND 180 DEG SHORT RADIUS (1D) - A-234 430 configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability). Note that SW cannot handle elbows greater than 90 degrees; therefore these bends have to be inserted as a fitting at the end of the route, then RMB on CPoint 2 and add to route (as per an eccentric reducer in the piping help). BEND 180 DEG LONG RADIUS (1.5D) DIN - STEEL DN25 DN200 Note that SW cannot handle elbows greater than 90 degrees; therefore these bends have to be inserted as a fitting at the end of the route, then RMB on CPoint 2 and add to route (as per an eccentric reducer in the piping help). BEND 180 DEG 3D - A-234 200+ configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability). Note that SW cannot handle elbows greater than 90 degrees; therefore these bends have to be inserted as a fitting at the end of the route, then RMB on CPoint 2 and add to route (as per an eccentric reducer in the piping help).

Revision: C Date of issue: 12 February 2004

12 of 28

MAKO ENGINEERINGS PIPING LIBRARY

BEND 180 DEG 5D - A-234 200+ configurations DN15 TO DN900 SCH 10 to 160 & STD to XXS (WT per availability). Note that SW cannot handle elbows greater than 90 degrees; therefore these bends have to be inserted as a fitting at the end of the route, then RMB on CPoint 2 and add to route (as per an eccentric reducer in the piping help).

Revision: C Date of issue: 12 February 2004

13 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

THREADED FITTINGS
All threaded fittings have intelligent custom properties built into their design tables (making extensive use of the concatenate & VLookup functions) to populate your Bills of Materials (example below).
ITEM 1 2 3 QTY 1 1 1 DESCRIPTION HEX BUSH - 25 x 20 BSP HEX NIPPLE - 20BSP - 150lb F/F REDUCER - 20 x 15 BSP CUT LENGTH SIZE 25x20 BSP 20BSP 20 x 15 BSP MATERIAL STEEL - GALV STEEL - GALV STEEL - GALV Kg EA 0.1 0.1 0.1

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a fitting with different material properties, etc. Threaded fitting make extensive use of the remove pipe function in the route sketch, this allows multiple fittings to be screwed into each other. HEXAGON BUSH GALVANISED (END) Configurations DN8x6 to DN100x80 in BSP & NPT. This part is used to start a piping route.

HEXAGON BUSH STEEL (END) Configurations DN8x6 to DN100x80 in BSP & NPT. This part is used to start a piping route.

HEXAGON BUSH GALVANISED (IN-LINE) Configurations DN8x6 to DN100x80 in BSP & NPT. This part is dragged onto a split point in a piping route.

14 of 28

MAKO ENGINEERINGS PIPING LIBRARY

HEXAGON BUSH STEEL (IN-LINE) Configurations DN8x6 to DN100x80 in BSP & NPT. This part is dragged onto a split point in a piping route. THREADED ELBOW F/F GALVANISED (45 & 90 DEG) Configurations DN6 to DN100 in BSP & NPT in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. THREADED ELBOW F/F STEEL (45 & 90 DEG) Configurations DN6 to DN100 in BSP & NPT in both 45 & 90 deg. This allows SW Piping to automatically select the appropriate elbow. THREADED REDUCING ELBOW F/F GALV (90 DEG) Configurations DN8x6 to DN80x65 in BSP & NPT. To use this elbow you must remove the auto-radius created in your route, then insert the elbow as you would any other fitting. This allows you to toggle the elbow to achieve the correct orientation. THREADED REDUCING ELBOW F/F STEEL (90 DEG) Configurations DN8x6 to DN80x65 in BSP & NPT. To use this elbow you must remove the auto-radius created in your route, then insert the elbow as you would any other fitting. This allows you to toggle the elbow to achieve the correct orientation. THREADED ELBOW M/F GALVANISED (90 DEG) Configurations DN8 to DN80 in BSP. To use this elbow you must remove the auto-radius created in your route, then insert the elbow as you would any other fitting. This allows you to toggle the elbow to achieve the correct orientation. THREADED ELBOW M/F STEEL (90 DEG) Configurations DN8 to DN80 in BSP. To use this elbow you must remove the auto-radius created in your route, then insert the elbow as you would any other fitting. This allows you to toggle the elbow to achieve the correct orientation.

Revision: C Date of issue: 12 February 2004

15 of 28

MAKO ENGINEERINGS PIPING LIBRARY

90 DEG THREADED ELBOW ANSI B16.11 A105 Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

Revision: C Date of issue: 12 February 2004

90 DEG THREADED ELBOW- ANSI B16.11 GALVANISED Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

45 DEG THREADED ELBOW ANSI B16.11 - A105 Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

45 DEG THREADED ELBOW ANSI B16.11 GALVANISED Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

THREADED CROSS A105 Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

THREADED CROSS- GALVANISED Modified SW library part to metric DN6 to DN100 2000#, 3000# & 6000#

16 of 28

MAKO ENGINEERINGS PIPING LIBRARY

HEX NIPPLE (150#) - GALVANISED (BOTH IN-LINE & END VERSIONS) DN6 to DN100 in BSP & NPT

Revision: C Date of issue: 12 February 2004

HEX NIPPLE (150#) STEEL (BOTH IN-LINE & END VERSIONS) DN6 to DN100 in BSP & NPT This part is dragged onto a split point in a piping route. HEX REDUCING NIPPLE (150#)- GALVANISED DN 8 X 6 TO DN 100 X 80 IN BSP & NPT This part is dragged onto a split point in a piping route. HEX REDUCING NIPPLE (150#) - STEEL DN 8 X 6 TO DN 100 X 80 IN BSP & NPT This part is dragged onto a split point in a piping route. HEX HEAD PLUG GALVANISED DN6 TO DN100 IN BSP & NPT

HEX HEAD PLUG STEEL DN6 TO DN100 IN BSP & NPT

THREADED REDUCER F-F-150# - GALVANISED(IN-LINE) DN 8 X 6 TO DN 80 X 70 BSP & NPT This part is dragged onto a split point in a piping route.

17 of 28

MAKO ENGINEERINGS PIPING LIBRARY

THREADED REDUCER F-F-150# - STEEL (IN-LINE) DN 8 X 6 TO DN 80 X 70 BSP & NPT This part is dragged onto a split point in a piping route. SOCKET 150# - GALVANISED (IN-LINE) DN6 to DN 100 in BSP This part is dragged onto a split point in a piping route.

Revision: C Date of issue: 12 February 2004

SOCKET 150# - STEEL (IN-LINE) DN6 to DN 100 in BSP This part is dragged onto a split point in a piping route.

TANK (HALF) SOCKET- 150# - GALVANISED (END) DN6 TO DN100 in BSP This part is used to start a piping route.

TANK (HALF) SOCKET- 150# - STEEL (END) DN6 TO DN100 in BSP This part is used to start a piping route.

THREADED EQUAL TEE 150# - GALVANISED DN6 to DN100 BSP & NPT

18 of 28

MAKO ENGINEERINGS PIPING LIBRARY

THREADED EQUAL TEE 150# - STEEL DN6 to DN100 BSP & NPT

Revision: C Date of issue: 12 February 2004

THREADED EQUAL TEE ANSI B16.11 A105 DN8 to DN100 2000, 3000 & 6000# Modified SW library part to metric per others

THREADED EQUAL TEE ANSI B16.11 GALVANISED DN8 to DN100 2000, 3000 & 6000# Modified SW library part to metric per others

THREADED UNION ANSI B16.11 A105 (IN- LINE) DN6 to DN80 3000 & 6000# This part is dragged onto a split point in a piping route. THREADED UNION ANSI B16.11 GALVANISED (IN- LINE) DN6 to DN80 3000 & 6000# This part is dragged onto a split point in a piping route. THREADED UNION ANSI B16.11 A105 (END) DN6 to DN80 3000 & 6000# This part is used to start a piping route.

19 of 28

MAKO ENGINEERINGS PIPING LIBRARY

THREADED UNION ANSI B16.11 GALVANISED (END) DN6 to DN80 3000 & 6000# This part is used to start a piping route.

Revision: C Date of issue: 12 February 2004

THREADED UNION F/F 150# - GALVANISED (END) DN6 to DN80 BSP & NPT This part is used to start a piping route.

THREADED UNION F/F 150# - STEEL (END) DN6 to DN80 BSP & NPT This part is used to start a piping route.

THREADED UNION F/F 150# - GALVANISED (IN-LINE) DN6 to DN80 BSP & NPT This part is dragged onto a split point in a piping route. THREADED UNION F/F 150# - STEEL (IN-LINE) DN6 to DN80 BSP & NPT This part is dragged onto a split point in a piping route.

20 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

SOCKET WELD FITTINGS

All socket weld fittings have intelligent custom properties built into their design tables (making extensive use of the concatenate function) to populate your Bills of Materials (example below).
ITEM 1 2 3 QTY 1 1 1 DESCRIPTION SOCKET WELD UNION - DN40 - 6000# SOCKET WELD UNION - DN40 - 3000# PIPE - 40NS, SCH 40 CUT LENGTH SIZE DN40 - 6000# DN40 - 3000# MATERIAL ASTM A105 ASTM A105 ASTM A106 Kg EA 1.4 1.4 0.2

285.82mm

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a fitting with different material properties, etc. SOCKET WELD UNION ANSI B16.11 A105 (END) DN6 to DN80 3000 & 6000# This part is used to start a piping route.

SOCKET WELD UNION ANSI B16.11 A105 (IN-LINE) DN6 to DN80 3000 & 6000# This part is dragged onto a split point in a piping route. xxx xxx xxx XXX XXX

21 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

VALVES
All valves have intelligent custom properties built into their design tables (making extensive use of the concatenate function) to populate your Bills of Materials (example below).
ITEM 1 2 3 QTY. 1 1 1 DESCRIPTION KNIFE GATE VALVE - 250NB TABLE D BALL VALVE - DN65 BSPT BALL VALVE - 3 PIECE - DN40-NPT SIZE DN250 TABLE D DN65 BSPT DN40 NPT kg 57.3 7.9 2.9

This intelligent design table approach allows them to be quickly modified to suit your companies requirements or easily copied to create a valve with different material properties, etc. 3 Piece Ball Valve. Configurations DN8 to 50 in BSP, NPT & SW This part is dragged onto a split point in a piping route. INSTRUMENT NEEDLE VALVE Configurations 6 to 25 NPT S/S 316 With both a round and Tee handle.

BUTTERFLY VALVE, LUGGED Configurations DN50 to DN300 in ANSI 150#, BST E & BST D. Modelled from Keystone AR2 catalogue.

BUTTERFLY VALVE, LUGGED NO HANDLE Configurations DN50 to DN900 in ANSI 150# and DN50 to DN300 in BST E & BST D. Modelled from Keystone AR2 catalogue. No handle to allow use with various actuators.

22 of 28

MAKO ENGINEERINGS PIPING LIBRARY

BUTTERFLY VALVE 50 TO 300 PNEUMATIC (THIS IS AN ASSEMBLY) Configurations DN50 to DN300 in ANSI 150#, BST E & BST D with both the single & double acting F79U/E actuators. Modelled from Keystone AR2 & 79U/E catalogues.

Revision: C Date of issue: 12 February 2004

BUTTERFLY VALVE 50 TO 900 GEARED HANDWHEEL (THIS IS AN ASSEMBLY) Configurations DN50 to DN900 in ANSI 150#, BST E & BST D with geared handwheel F427 . Modelled from Keystone AR2 & F427 catalogues. FLANGE BALL VALVE PNEUMATIC (THIS IS AN ASSEMBLY) DN15 to 50, Full & Reduced Bore 150# & 300# with F79U/E actuator. Modelled from Keystone F344 & 79U/E catalogues. F79U/E PNEUMATIC ACTUATOR Sizes 003 to 036, Spring Return & Double Acting fitted with positioner.. Modelled from Keystone 79U/E catalogue. BALL VALVE DN80-200 - FLANGED DN80 to 200, 150# & 300# Modelled from Keystone F344 & F345 catalogues.

23 of 28

MAKO ENGINEERINGS PIPING LIBRARY

BALL VALVE DN65-100 REDUCED BORE DN65 to 100, BSPT, NPT, SW & Sch 40 BW - With either handle or pneumatic actuator. Modelled from Keystone F382 & 79U/E catalogues. This part is dragged onto a split point in a piping route. BALL VALVE DN15-50 - FLANGED DN15 to 50, 150# & 300# Modelled from Keystone F344 & F345 catalogues.

Revision: C Date of issue: 12 February 2004

BALL VALVE DN15-50-FLANGED FOR ACTUATOR DN15 to DN50, 150# & 300# to accept F79U/E. Modelled from Keystone F344 & F345 catalogues. GATE VALVE CAST STEEL DN50 to DN300, 150# & 300#

KNIFE GATE VALVE DN25-600 DN250 to 600, Table D. Modelled from the Keystone F952 catalogue.

24 of 28

MAKO ENGINEERINGS PIPING LIBRARY

JORDAN MK 50 BACK PRESSURE VALVE DN15 to DN50, NPT & BSP Modelled from the Jordan Treloar MK 50 catalogue.

Revision: C Date of issue: 12 February 2004

SPIRAX SARCO DCV 2 WAFER CHECK VALVE DN15 to DN100. Can be fitted between the following flanges: BS10 table E (except DN65 & 80) Table H and BS4504/DIN PN6 to 40. Modelled from the Spirax Sarco product handbook (1995-96)

25 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

MISCELLANEOUS PIPING ITEMS

All parts have intelligent custom properties built into their design tables (making extensive use of the concatenate function) to populate your Bills of Materials (example below).
ITEM 1 QTY 1 DESCRIPTION STRAUB COUPLING (W2 - EPDM) - DN80 (OD 88.9) SIZE PIPE OD 88.9 MATERIAL STRAUB METAL GRIP (W2 - EPDM) Kg EA 2

This intelligent design table approach allows them to be quickly modified to suit your companys requirements or easily copied to create a similar part with different material properties, etc. STRAUB COUPLING METAL GRIP (END) PIPE OD 30mm to 609.6 Material grades W1, W2 & W4 with both NBR & EPDM seals. This part is used to start a piping route. STRAUB COUPLING METAL GRIP (IN-LINE) PIPE OD 30mm to 609.6 Material grades W1, W2 & W4 with both NBR & EPDM seals. This part is dragged onto a split point in a piping route

26 of 28

MAKO ENGINEERINGS PIPING LIBRARY

Revision: C Date of issue: 12 February 2004

MISCELLANEOUS ASSEMBLIES
Below are a collection of assemblies that you may find useful for use in a piping / plant installation project. DISCLAIMER: Please note that any pressure containing parts/vessels MUST have the appropriate design calculations & design verification conducted by an accredited company/person to ensure that they comply with your countrys design codes and are deemed suitable for use in your piping/ pressure vessel design. Steam header assembly. Modelled using SW Piping plus a number of my library parts & assemblies and controlled by a driving part (containing the driving sketch & associated planes). Shown here with a 400nb body and nozzles ranging from 300nb to 80nb. However, this header can be copied, re-named and re-sized to suit your requirements. Steam Trap (Thermodynamic) Set. Based on Spirax Sarco thermodynamic steam trap set inlet isolating valve, strainer, steam trap, sight/check & discharge isolating valve. Has 2 configurations: 15 & 20 BSP Steam Trap (Float) Set. Based on Spirax Sarco float type steam trap set inlet isolating valve, strainer, steam trap, sight/check & discharge isolating valve. Has 2 configurations: 15 & 20 BSP

27 of 28

MAKO ENGINEERINGS PIPING LIBRARY

ELLIPTICAL INSPECTION OPENING AS 1210 (material AS1548-7-460R) Configurations: 400x300, 225x180, 180x125 & 115x90. Based on the now defunct Rheem Tank Products inspection openings..

Revision: C Date of issue: 12 February 2004

28 of 28