Pasgt Module Prelim To Final
Pasgt Module Prelim To Final
Pasgt Module Prelim To Final
MODULE
IN
JOHN B. LACSON FOUNDATION MARITIME UNIVERSITY - MOLO, INC.
(FORMERLY ILOILO MARITIME ACADEMY)
BACHELOR OF SCIENCE IN MARINE ENGINEERING
Course outline:
PRELIM
1. Operation principles
2. Basic construction
3. Shafting Installations and Propeller
MODULE 1 (Week 1-6) 30 HRS.
1. FAN - is a powered machine used to create flow within a fluid, typically a gas such as air. A fan
consists of a rotating arrangement of vanes or blades which act on the air.
2. LOW PRESSURE COMPRESSOR - Compresses the incoming air of low pressure inside the
combustion chamber.
3. HIGH PRESSURE COMPRESSOR - Compresses the incoming air of high pressure inside the
combustion chamber.
4. DIFFUSER - slows down the compressor delivery air to reduce flow losses in the combustor.
Slower air is also required to help stabilize the combustion flame and the higher static pressure
improves the combustion efficiency.
5. IGNITER - a device for igniting a fuel mixture in an engine inside combustion chamber of gas
turbine engine.
6. COMBUSTOR - Fuel is burned continuously after initially being ignited during the engine
start. Once the air flows through the diffuser, it enters the combustion section, also called the
combustor.
7. HIGH PRESSURE TURBINE - Extracts the energy from the high-pressure, high-velocity gas
flowing from the combustion chamber and converting the gaseous energy to mechanical
energy in the form of shaft power.
8. LOW PRESSURE TURBINE - Extracts the energy from the low-pressure, high-velocity gas
flowing from the combustion chamber.
9. ROTOR - A rotating wheel or group of wheels in a turbine.
10. BEARING- is a machine element that constrains relative motion to only the desired motion,
and reduces friction between moving parts.
11. DISTRIBUTOR- Air leaves the compressor through exit guide vanes, which convert the radial
component of the air flow out of the compressor to straight-line flow. The air then enters the
diffuser section of the engine, which is a very divergent duct.
12. PRESSURE LUBRICATION-A force lubrication system serves to ensure lubrication of the
bearings and gears and to maintain sufficiently cool temperatures, mostly by eliminating
friction.
13. SHROUD - The primary function of the shrouds is to provide a cylindrical surface for
minimizing tip clearance leakage. The secondary function is to provide a high thermal
resistance between the hot gases and the comparatively cool shell.
14. INTAKE- the inlet is a duct that is required to ensure smooth airflow into the engine despite air
approaching the inlet from directions other than straight ahead.
15. EXHAUST- Turbine exhaust gases pass through the propelling nozzle to produce a high-
velocity jet. The nozzle is usually convergent with a fixed flow area. After the gas has passed
through the turbine, it is discharged through the exhaust. Though most of the gaseous energy
is converted to mechanical energy by the turbine.
A simple gas turbine is comprised of three main sections a compressor, a combustor, and a power
turbine. The gas-turbine operates on the principle of the Brayton cycle, where compressed air is mixed
with fuel, and burned under constant pressure conditions.
In an ideal gas turbine, gases undergo four thermodynamic processes: an isentropic compression, an
isobaric (constant pressure) combustion, an isentropic expansion and heat rejection. Together, these
make up the Brayton cycle .Explain in Gas control system diagram.
.
Advantages
1. Gas turbines are capable of reaching full load operation in a matter of
minutes. These engines are very popular for using as peak power plants, this
due to their ability of be taken into service during peak power demand when
and as required.
2. Furthermore, they have a very attractive initial cost as compared with steam
turbines.
3. High power-to-weight ratio.
4. Require much less water than steam turbines power plants.
5. Smaller size and weight compared to steam turbines.
6. Less space is needed for installation.
Disadvantages
1. One of the disadvantages of gas turbines is their limited ability to use different
fuels in comparison with steam turbines. In fact, just a little variation in the
fuel specs used in a gas turbine can lead to efficiency drop, increase
maintenance factor, early inspection etc.
2. Low part load efficiency.
3. Due to high operating temperatures, special and expensive materials are
needed.
4. About two thirds of the power produces is used to drive the compressor.
5. External source of power needed to start self-sustained operation.
Steam Turbine
A steam turbine is a form of heat engine that extracts energy from high-pressure steam to produce
electricity. These engines generate approximately the 90% of the electricity in the U.S. Steam cycle
power plants operation are based on the Rankine Cycle. The fundamental operation of this cycle is
described as follows. Water is pumped at high pressure into a boiler where heat from the combustion
process is used to generate steam. The steam then passes through a steam turbine that rotates a shaft
that is connected to an electrical generator. The spinning of the electrical generator produces electricity.
The low pressure and low-temperature steam coming from the turbine is then passed through a
condenser that decreases the temperature of the steam to convert it back to saturated water. The
saturated water is then pumped back to the boiler closing the cycle.
A steam turbine is a form of heat engine that extracts energy from high-pressure steam to
produce electricity. These engines generate approximately the 90% of the electricity . Steam
cycle power plants operation are based on the Rankine Cycle. The fundamental operation of this
cycle is described as follows. Water is pumped at high pressure into a boiler where heat from
the combustion process is used to generate steam. The steam then passes through a steam
turbine that rotates a shaft that is connected to an electrical generator. The spinning of the
electrical generator produces electricity. The low pressure and low-temperature steam coming
from the turbine is then passed through a condenser that decreases the temperature of the
steam to convert it back to saturated water. The saturated water is then pumped back to
the boiler closing the cycle.
Advantages
1. One of the main advantages of steam turbines is the boiler ability to burn
multiple types of fuels. The boiler is capable of burning different fuels at each
stage of the start-up process. For instance, it can use LPG for ignition, light
diesel oil for start-up and then heavy oil for continuous operation as an
example.
2. Steam turbines have a high power-to-weight ratio which makes them more
practical than reciprocating engines. Also, for a given power output, their size
is smaller and produce less vibrations than their reciprocating counterparts.
3. Power generation is not affected by atmospheric conditions as it operates on a
closed cycle.
4. Another advantages of steam turbine power plants compared to gas turbines
are the high operating efficiency, higher reliability and high operating
efficiencies.
Disadvantages
Function: Turbojet, jet engine in which a turbine-driven compressor draws in and compresses air, forcing it
into a combustion chamber into which fuel is injected. Ignition causes the gases to expand and to rush first
through the turbine and then through a nozzle at the rear.
Application: When used in a turbojet application, where the output from the gas turbine is used in a
propelling nozzle, raising the turbine temperature increases the jet velocity.
Components:
1. Compressor
2.Combustor
3. Shaft
4. Turbine,
5. Exh. Nozzle
Working Principle: Air is drawn into the engine through the inlet side by the
propeller and compressor and compressed and heated by the compressor.
Fuel is then added in the combustion chamber and ignited. The gases flow through the turbine and make it
spin. These gases bounce back and shoot out of the rear of the exhaust, pushing the plane forward.
Application: Turboprop aircraft were specifically designed to be the most efficient at low altitudes and slower
speeds under 450 mph. They are extremely efficient and burn less fuel than most light jets.
STRUT - a rod or bar forming part of a framework and designed to resist compression.
Components:
1. Propeller
2. Gearbox
3. Shaft/Strut
4. Compressor
5. Combustor
6. Turbine
7. Exh. Nozzle
3. Turbofan - The turbofan or fanjet is a type of air breathing jet engine that is
widely used in aircraft propulsion. The ratio of the mass-flow of air
by passing the engine core divided by the mass-flow of air passing
through the core is referred to as the bypass ratio.
Working Principle: Air is drawn into the engine through the inlet side by the fan blade and compressor and
compressed and heated by the compressor. Fuel is then added in the combustion chamber and ignited. The
gases flow through the turbine and make it spin. These gases bounce back and shoot out of the rear of the
exhaust, pushing the plane forward.
Application: The turbofan or fanjet is a type of air-breathing jet engine that is widely used in aircraft
propulsion.
Components:
1. Fan,
2. Low-pressure compressor
3. High-press. compressor
4. High-press. Shaft
5. Low-press. Shaft
6. Combustor
7. High-press. Turbine
8. Low-press. Turbine
9. Exh. Nozzle
2) Basic construction
At the end of the topic, the students will be able to:
Describe the types of turbine and their features
List the attached equipment and explain their features and functions in simple terms
Lesson 6 :Using visual aids to describe the three main components of gas turbine as:
• compressor
• combustion chamber
• turbine
There are three basic categories of gas turbine engine compressor: axial compressor, centrifugal compressor
and mixed flow compressor. A fourth, unusual, type is the free-piston gas generator, which combines the
functions of compressor and combustion chamber in one unit.
The compressor section of the gas turbine engine has many functions. Its primary function is to supply air in
sufficient quantity to satisfy the requirements of the combustion burners. A secondary function of
the compressor is to supply bleed-air for various purposes in the engine and aircraft.
1. axial flow compressor is a gas compressor that can continuously pressurize gases. It is a rotating,
airfoil-based compressor in which the gas or working fluid principally flows parallel to the axis of rotation, or
axially.
Compressors are typically driven by an electric motor or a steam or a gas
turbine. Axial-flow: having the fluid or gas flowing parallel to the axis axial-
flow turbine axial-flow pump — compare radial-flow
Axial compressor is usually used in gas turbine. Axial compressors are used in medium- to large-thrust gas
turbine engines, because the alternative centrifugal units would be too heavy and too large in the cross-
sectional area.
.
3. mixed flow compressor - A mixed flow compressor, or diagonal compressor, combines axial and
radial components to produce a diagonal airflow compressor stage
Combustion chambers are confined spaces in internal and external combustion engines to burn the fuel air
mixture.
In a gas turbine engine, the combustor or combustion chamber is fed high pressure air by the compression
system. The combustor then heats this air at constant pressure
There are two types of internal combustion chambers: Piston type internal combustion engines consist of a
cylinder with a piston inside and are used in cars and boats. Combustors are combustion chambers used in gas
turbines and jet engines.
Gas turbines. Many warships built since the 1960s have used gas turbines for propulsion, as have a few
passenger ships, like the jetfoil. Gas turbines are commonly used in combination with other types of engine.
Most recently, RMS Queen Mary 2 has had gas turbines installed in addition to diesel engines.
Lesson 3 :List the attached equipment and explains their feature and functions in simple
terms
SHOW VIDEO OF:
A propeller is a type of fan that transmits power by converting rotational motion into thrust. A pressure
difference is produced between the forward and rear surfaces of the airfoil-shaped blade, and a fluid (such as
air or water) is accelerated behind the blade.
A propeller is a rotating fan like structure which is used to propel the ship by using the power generated
and transmitted by the main engine of the ship. A vessel's propeller works by thrusting a column of water
away from the main body of the ship, thereby producing a reactive force that moves the boat forward. Most
naval vessels use a screw-type propeller that transmits thrust through the main shaft to the thrust bearing.
The construction process of the propeller includes attaching a number of blades to the hub or boss by
welding or forging in one piece. A marine Propeller is constructed by sections of helicoidal surfaces acting
together to rotate through water with a screw effect.
Rope guards are a protection barrier for propeller shafts shielding them against line entanglement around
main shafts. Typically attached by means of welding or bolted with locking wires in place. For every vessel
rope guards are the protection barrier for propeller shafts shielding them against line entanglement and
damage on the shaft seal system. Typically rope guards are attached by means of welding or bolted with
locking wires in place. Removal of entangled ropes and nets
The stern tube is a narrow hole in the hull structure at the rear end (aft peak) of
the ship, through which the propeller
shaft passes and connects the engine and propeller. The ship's tail shaft (or
propeller shaft), which transfers power from the main engine, runs inside the stern tube and connects to
the propeller
Stern tube bearing - a long bushing or bearing through the stern of a ship to support the after part of the
propeller shaft. The main function of stern tube bearings is to allow an unrestricted and smooth rotation of
the propeller shaft. Apart from stern bearings, the stern tube also houses water and oil sealing
glands known as the stern glands. The stern tube is a sensitive part of the ship where the sea water can easily
seep inside.
Shaft seal - are used on rotating, reciprocating, and oscillating shafts to contain oil and grease and exclude
contaminants.
intermediate shaft – supported by the thrust block, intermediate bearings and the sterntube bearing. A
sealing arrangement is provided at either end of the tailshaft with the propeller and cone completing the
arrangement.
propeller shaft -transmits power from the gearbox to the differential gear in a motor vehicle or from the
engine to the propeller in a ship or aircraft
Shaft bearing- carries the total weight of propeller shaft located inside the stern tube.
plumber block - lessen the reduction of stress due to the weight and cause propeller shafting misalignment.
Thrust bearing – with any propulsion system the thrust from the propeller must be transmitted into the hull
to drive the ship through the water. The thrust bearings in this case are mounted aft of the propulsion motors
before the shaft bearings (plummer blocks).
Lignum Vitae Water-Lubricated bearings commonly replace composite, plastic, bronze, babbit and oil
filmed bearings. The material is the oldest bearing in service with unmatched longevity in water
applications. It has tremendous load bearing qualities and unique shock absorbing qualities that no
other material can match. This material has successfully returned to the Hydro Power market and
now will return to the Marine market.
There are a few types(3 types) of major stern tube seals on the market today all with one job, to keep
the ship moving through the water, and the water out of the ship. These include;
1. labyrinth Seals
The aft seal contains three lip seals. The first two lip seals form a barrier against water ingress and
the third one prevents oil leakage from the stern tube into the surrounding water.
The general working principle of Labyrinth seals is to create a series of barriers that gradually reduce
pressure such that the final seal is not subject to a large volume of sealing media at these higher
pressures. The purposeful long and winding path that the sealing liquid must follow can then be
sealed watertight by conventional means such as an O-ring or lip seal.
While an effective means of sealing, this method has inherent issues with longevity as the final seals
are commonly elastomer based and in contact with rotating equipment at all times thus subject to
friction wear. Elastomers have a limit in terms of surface speed capabilities, which diminishes over
time. Incredibly tight tolerances are also required as the passages begin to narrow, driving
manufacturing cost and creating installation and premature failure challenges.
The common issues with the above labyrinth seals of failure due to friction has been solved by the
mechanical face seal. In order to handle the frictional loading, mechanical face seals get around the
heat caused by frictional loading by using the sealing media for a cooling and friction reducing effect..
Where friction is reduced, and where heat is reduced, so is wear. This means that mechanical face
seals are designed to run for long periods of time at high speeds.
Similar to labyrinth seals, mechanical face seals require additional support materials such as flushing
water, oil and grease to keep them running. The materials chosen are also much more robust than
some of the common ceramic based materials which are prone to breakage and cracking in harsh
usage conditions.
3. Packing Type
Perhaps the oldest and most utilized system of sealing of rotating equipment is through the use of
packing. Materials such as fibrous rope, oakum, carbon and graphite based materials have been
used for as long as there have been rotating shafts driving ships through the world’s oceans. There
have been great advances in the materials created for use in packing applications, however these
systems limit operation speed profiles, require increased maintenance and must be checked and re-
packed at frequent intervals.
Lesson 2: Describe the details of oil shaft seal and stern tube bearing including
their components
- Shaft seals also known as lip seal - are used to seal rotary elements, such as a shaft or rotating
bore. Depending on the seal type these two angles are varied to create a pressure distribution at the
seal contact point. Shaft seal in machinery it is a device that prevents the passage of fluids along a
rotating shaft.
SHAFT SEAL
- A propeller shaft - is a mechanical component for transmitting torque and
rotation, usually used to connect other components of a drive train that cannot
be connected directly because of distance or the need to allow for relative
movement between them.
Intermediate shaft - The propeller of the ship is fitted at the aft and attached to
a crankshaft coming from the main engine. The propeller shaft or tail shaft is
supported by a bearing arrangement which acts as an intermediate phase
between the sea and the ship.
-Shaft bearing - A bearing is a machine element that constrains relative motion
to only the desired motion, and reduces friction between moving parts. The
simplest form of bearing, the plain bearing, consists of a shaft rotating in a hole.
Lubrication is often used to reduce friction
- Thrust bearing - A bearing located inside the ship to transmit the propeller thrust from the shafting
to the hull structure. The thrust bearing consists of a thrust collar on the crankshaft,
a bearing support, and segments of steel with white metal.
A thrust bearing is a particular type of rotary bearing. Like other bearings they permit rotation
between parts, but they are designed to support a predominantly axial load. Thrust ball bearings,
composed of bearing balls supported in a ring, can be used in low thrust applications where there is
little axial load.
Thrust bearings absorb axial loads from rotating shafts into the stationary housings or mounts in
which they are turning.
Thrust collar
Details of oil shaft seal and stern tube bearing including their components
An oil seal normally consists of three basic components: the sealing element, the metal case
and the spring. The purpose of the sealing element is to stop the fluid from leaking between the shaft
and housing.
The main function of stern tube bearings is to allow an unrestricted and smooth rotation of the
propeller shaft. Apart from stern bearings, the stern tube also houses water and oil sealing glands
known as the stern glands. The stern tube is a sensitive part of the ship where the sea water can
easily seep inside.
There are two types of propellers in the field of professionally used ships: The controllable
pitch propeller (CPP) or swivel blade propeller. The fixed pitch propeller.
Pitch is defined as "the distance a propeller would move in one revolution if it were moving through a
soft solid, like a screw through wood." For example, a 21-pitch propeller would move forward 21
inches in one revolution.
A variable-pitch propeller or controllable-pitch propeller (CPP) is a type of propeller with blades
that can be rotated around their long axis to change the blade pitch.
1. Controllable pitch propellers can be used to run the ship in forward and astern direction
both, without the requirement to change the direction of rotation of the engine. The propeller
works on the principle of lift generated by each aero foil section of the blade.
2. Most of the propellers that are used in ships are fixed pitch propellers (FPP). It is this twist in the
blade that results in the forward motion of the propeller with each rotation. Parts of screw propeller. It
is pretty much what you see on a screw. The angle of the thread is actually what is called the
pitch angle.
Parts of 4 Blades fixed pitch propellers
1. Back of Blade
2. Face of Blade
3. Leading Edge
4. Face Pitch Angle
5. Pitch Datum Line
6. Blade Tip
7. Blade Root
8. Fairing Cone
9. Trailing Edge
10. Rake Datum Line
• diameter
• pitch
• pitch ratio
• boss ratio
• pressure side
• suction side
• leading edge
• trailing edge
blade section
• blade rake
-Diameter - Basically, a propeller design is carried out by one of the two following methods:
The different propellers tested have varied parameters such as number of blades, blade area, pitch
ratio etc. Based on these results and the requirement of the vessel, the parameters can be selected
to obtain the suitable design.
- Diameter usually increases for propellers used on slower boats and decreases
for faster boats," the manual continues.
- Pitch - Pitch is defined as "the distance a propeller would move in one revolution if it were moving
through a soft solid, like a screw through wood." For example, a 21-pitch propeller would move
forward 21 inches in one revolution.
- Pitch ratio - Typically blades are twisted to guarantee constant pitch along the blades from root to
tip. Often a pitch ratio will be supplied. This is simply the ratio of pitch to diameter, usually in
millimeters, and typically falls between 0.5
and 2.5 with an optimal value for most vessels closer to 0.8 to 1.8.
- Boss ratio -The ship propeller has two hydrodynamic surfaces: Face and Back. To put it simply,
the cross section of blades coupled with the boss when looked from behind the ship is called the
Face, also known as the 'palm'.
-Pressure side or pressure face of the blade. This is the side that faces aft (backwards) and
pushes the water when the vessel is in forward motion. The back of the blade is the low pressure side
or the suction face of the blade. This is the side that faces upstream or towards the front of the
vessel.
- Suction side. The back of the blade is the low pressure side or the suction face of the blade. This is
the side that faces upstream or towards the front of the vessel.
- Leading edge. This is the side that faces upstream or towards the front of the vessel. The leading
edge of a propeller blade or any foil is the side that cuts through the fluid. A right-
handed propeller rotates clockwise when
propelling a vessel forward, as viewed from the stern of the ship.
- Blade rake. Rake is the amount of degrees the propeller blades angle perpendicular to the
propeller hub. Rake can be
slightly negative (leaning towards the boat), or positive (leaning away from the boat). The range of
degrees could vary from -5 to +30 degrees. An average rake angle for most outboard propellers is 15
degrees.
SHOW VIDEOS
Lesson 8: Describe a highly -skewed (skew back) propeller and its advantages
A fixed-pitch propeller is a propeller whose pitch angle (the incidence of the blades with respect to
the plane of rotation) cannot be changed.
Construction: Fixed Pitch Propeller. The fixed pitch type propellers are casted and the position of
the blades and hence the position of the pitch is permanently fixed and cannot be changed during the
operation. They are normally made from copper alloy.
Design: Considerations are made to match the engine's power and shaft speed, as well as the size
of the vessel and the ship's operating speed, with an appropriately designed propeller.
Principle: It is this twist in the blade that results in the forward motion of the propeller with each
rotation. The more the pitch angle, the more distance is traveled by the screw in one rotation, that is,
the more is the pitch. Similarly, propellers act on the principle of screw. Hence the term screw
propeller.
Application: Most of the propellers that are used in merchant ships are fixed pitch propellers (FPP).
It is this twist in the blade that results in the forward motion of the propeller with each rotation.
Controllable pitch propeller (CCP) and its mechanism of changing blade angle
A controllable pitch propeller is of the built-up type with separate boss and blades, the blades being
capable of being turned through the required angle to the plane of rotation to change from full pitch
angle ahead to full pitch angle.
Pitch is defined as "the distance a propeller would move in one revolution if it were moving through a
soft solid, like a screw through wood." For example, a 21-pitch propeller would move forward 21
inches in one revolution.
Construction: A controllable pitch propeller is made up of a boss with separate blades mounted into
it. An internal mechanism enables the blades to be moved simultaneously through an arc to change
the pitch angle and therefore the pitch.
Design: A variable-pitch propeller or controllable-pitch propeller (CPP) is a type of propeller with
blades that can be rotated around their long axis to change the blade pitch.
Principle: Since the pitch of the propeller determines the amount of thrust generated by the propeller,
a change in the pitch angle can bring about a change in the speed of the ship.
Application: A controllable pitch propeller is useful in changing the speed of the ship without changing
the speed or rpm of the main engine
Blade pitch or simply pitch refers to turning the angle of attack of the blades of a propeller or
helicopter rotor into or out of the wind to control the production or absorption of power. Wind turbines
use this to adjust the rotation speed and the generated power.
- A non-reversible engine can be used for both forward and astern operation of the ship. Hence,
the weight of the engine and propulsion machinery is reduced considerably when compared to
what is required in propulsion systems equipped with fixed pitch propellers.
- Since the pitch of the propeller determines the amount of thrust generated by the propeller, a
change in the pitch angle can bring about a change in the speed of the ship. A controllable pitch
propeller is useful in changing the speed of the ship without changing the speed or rpm of the
main engine.
- Due to the above reason, the speed of the ship can be handled from the navigation bridge
directly. In case of fixed pitch propellers, the marine engineer needs to be intimidated in order to
change the ship’s speed. Therefore CPP technology is used for obtaining faster response of
speed change.
- The efficiency of astern condition in case of fixed pitch propellers is less than that of controllable
pitch propeller in astern condition. However, there are many disadvantages of using a controllable
pitch propeller to a fixed pitch propeller. It is important to know them too.
- The pitch control mechanism installed in the hub is complicated enough to demand proper
inspection at regular intervals. The installation process is also more complicated as compared to
that of fixed pitch propeller system.
- Controllable pitch propellers have a very high initial cost. And this cost increases rapidly with
increasing diameter of the propeller.
- Due to pitch control mechanisms housed inside the hub, the length and the diameter of the hub
is also high as compared to the fixed pitch propeller systems.
Show video:
Controllable Pitch Propellers, fixed pitch propeller and Bow Thruster thruster
Lesson 11: Define the cavitation of propellers and explains its generating
mechanism
The cavitation of propellers and explains its generating mechanism
propeller cavitation. Formation of vapor-filled and air-filled bubbles or cavities in water at or on the
surface of a rotating propeller, occurring when the pressure falls below the vapor pressure of water.
Cavitation is a phenomenon in which rapid changes of pressure in a liquid lead to the formation of
small vapor-filled cavities, in places where the pressure is relatively low. The process in which a void
or bubble in a liquid rapidly collapses, producing a shock wave, is called inertial cavitation.
The collapsing bubbles are filled with very low-pressure water vapor and when they collapse damage
is done to many surfaces. Cavitation is a drag on efficiency because of the increased friction. Even
worse, cavitation can cause vibration because of uneven prop loads and damage or break
equipment.
A skewed propeller is a propeller with a specialized blade design fitted to the ship in order to improve
the propulsion performance and efficiency of the propeller. Such design reduces the induced vibration
and noise due to cavitation.
Preventing cavitation: remove fouling, nicks and scratch. Increase or decrease the engine rpm
smoothly to avoid an abrupt change in thrust. Keep appropriate pitch setting for CPP.
Lesson 12: Define the propeller singing and explains its generating mechanism and
preventive measures
The propeller singing and explains its generating mechanism and preventive measures
Propeller “singing” phenomenon is defined as the resonance between the natural frequency of the
propeller blade tip and the vortex shedding frequency at trailing edge of the blade.
In fluid dynamics, vortex shedding is an oscillating flow that takes place when a fluid such as air or
water flows past a bluff (as opposed to streamlined) body at certain velocities, depending on the size
and shape of the body.
Cause of vortex shedding happens when wind hits a structure, causing alternating vortices to form at
a certain frequency. This in turn causes the system to excite and produce a vibrational load.
Historically, it has been very difficult to calculate by hand.
Some propellers in service produce a high-pitched noise, often referred to as Singing. This sound
typically is a clear harmonic tone much like a humming or ringing wine glass. Also, the less number of
blades the less cases of "singing".
The generating mechanism of propeller singing based on the theory of unsteady hydrodynamics of
cyclic spiral separated flow and points out the singing is a typical result of hydrodynamic elastic
resonance induced by Karman vortex. This can be prevented by reducing propeller blade trail edge to
1mm on the basis of compliance with class requirement.
Kármán vortex is a repeating pattern of swirling vortices, caused by a process known as vortex
shedding, which is responsible for the unsteady separation of flow of a fluid around blunt bodies. It is
named after the engineer and fluid dynamicist Theodore von Kármán, and is responsible for such
phenomena as the "singing" of suspended telephone or power lines and the vibration of a car
antenna at certain speeds.
Course outline:
MIDTERM
3. (Cont.) Shafting Installations and Propeller
4 .Fluid Flow and Characteristics of Major Systems
5. Main engine and associated auxiliaries
MODULE 2 (Week 7-12) 30 HRS.
• lubricating oil
• cooling fresh water
• cooling sea water
• Gas
The Exhaust gas from the cylinder unit is sent to exhaust gas receiver where the fluctuating pressure
generated from different cylinders are equalized. From here, the gases which are at constant
pressure are sent to turbocharger where waste heat is recovered to provide additional scavenge air to
engine.
The modern exhaust gas system of marine engines is designed in such a way that the unused gases
coming out of the cylinders are further directed to turbocharger and exhaust gas boiler to recover
most of the waste energy from the same.
To utilize the maximum energy from the waste gases, the exhaust gas system of marine engine is
provided with the following components:
Exhaust gas boiler is considered to be one of the most efficient waste heat recovery system
designed for a ship.
Silencer is used to reduce the noise level in the exhaust gas manifold and they are generally placed
after the EGB.
A spark arrester can be fitted in the exhaust piping system to prevent sparks from the exhaust gas
being spread over deckhouse. It is placed at the end of the exhaust gas system of the engine.
The expansion joints are to be chosen with an elasticity that limits the forces and the moments of
the exhaust gas outlet flange of the turbocharger as stated for each of the turbocharger makers.
• Lubricating oil
Lubrication is the process or technique employed to reduce friction between, and wear of one or both,
surfaces in proximity and moving relative to each other, by interposing a substance called a lubricant
in between them
Lubricating oil system: Lubricating oil for an engine is stored in the bottom of the crankcase, known
as the sump, or in a drain tank located beneath the engine. The oil is drawn from this tank through a
strainer, one of a pair of pumps, into one of a pair of fine filters. It is then passed through a
cooler before entering the engine and being distributed to the various branch pipes.
Cooling of engines is achieved by circulating a cooling liquid around internal passages within the
engine. The cooling liquid is thus heated up and is in turn cooled by a sea water circulated cooler.
Without adequate cooling certain parts of the engine which are exposed to very high temperatures, as
a result of burning fuel, would soon fail.
Cooling enables the engine metals to retain their mechanical properties. The usual coolant used is
fresh water: sea water is not used directly as a coolant because of its corrosive action. Lubricating oil
is sometimes used for piston cooling since leaks into the crankcase would not cause problems. As a
result of its lower specific heat however about twice the quantity of oil compared to water would be
required
Water carried in pipes is used to cool machinery. The main engine is cooled by two separate but
linked systems: an open system (sea-to-sea) in which water is taken from and returned to the sea
(seawater cooling), and a closed system where freshwater is circulated around an engine casing
(freshwater cooling).
Freshwater is used to cool machinery directly, whereas seawater is used to cool freshwater passing
through a heat exchanger. The particular feature of an engine cooling system is continuous fluid flow.
Fluid in motion causes abrasive corrosion and erosion. To reduce the effects of turbulent flows,
seawater systems incorporate large diameter mild steel pipes, the ends of which open to the sea
through sea chests where gate valves are fitted.
The various cooling liquids which circulate the engine are themselves cooled by sea water. The usual
arrangement uses individual coolers for lubricating oil, jacket water, and the piston cooling system,
each cooler being circulated by sea water. Some modern ships use what is known as a 'central
cooling system' with only one large sea-water-circulated cooler. This cools a supply of fresh water,
which then circulates to the other Individual coolers. With less equipment in contact with sea water
the corrosion problems are much reduced in this system.
Cooling sea water Diagram
From the sea suction one of a pair of sea-water circulating pumps provides sea water which
circulates the lubricating oil cooler, the jacket water cooler and the piston water cooler before
discharging overboard. Another branch of the sea water main provides sea water to directly cool the
charge air (for a direct-drive two-stroke diesel).
Lesson 1: Explain the outline of main machinery system listing associated systems including
their Components
Engines
The engine room of a motor vessel typically contains several engines for different purposes.
Main, or propulsion engines are used to turn the ship's propeller and move the ship through the
water. They typically burn diesel oil or heavy fuel oil, and may be able to switch between the two.
There are many propulsion arrangements for motor vessels, some including multiple engines,
propellers, and gearboxes.
Main engines components includes:
The power dependent lubrication of the pistons, cylinders and exhaust valve spindles is performed by
a separate cylinder lubrication system.
• Circulation System
Injection valves and fuel distributors are kept hot by circulation of heated fuel. For each cylinder there
is a separate sub-system. A hot fuel circulating line is taken from the engine’s fuel supply pipe and
the hot fuel oil is circulated through the cylinder fuel injection pump, the fuel injectors and the fuel
distribution block. After fl owing through these, the fuel enters a return circulating line and then
passes into a common return pipe. This common return pipe is connected to the booster return pipe
via an orifice, located after the pressure-retaining valve and so the fuel used for injector and
distributor heating can flow readily back to the mixing unit.
Auxiliary engines
Smaller, but still large engines drive electrical generators that provide power for the ship's electrical
systems. Large ships typically have three or more synchronized generators to ensure smooth
operation. The combined output of a ship's generators is well above the actual power requirement to
accommodate maintenance or the loss of one generator.
On a steamship, power for both electricity and propulsion is provided by one or more large boilers
giving rise to the alternate name boiler room. High pressure steam from the boiler is used to drive
reciprocating engines or turbines for propulsion, and also turbo generators for electricity. Besides
propulsion and auxiliary engines, a typical engine room contains many smaller engines, including
generators, air compressors, feed pumps, and fuel pumps. Today, these machines are usually
powered by small diesel engines or electric motors, but may also use low-pressure steam.
Air starting system for marine diesel engine
Air at a pressure of 20 to 30 bar is required for starting main and auxiliary diesel engines in motor
ships and for the auxiliary diesels of steamships. Control air at a lower pressure is required for ships
of both categories and whether derived from high pressure compressors through reducing valves or
from special control air compressors, it must be clean, dry and oil free.
A starting air system for main diesels normally has two air compressors and two reservoirs with
sufficient capacity for twelve main engine starts (six if a non-reversible engine). The receivers must
store sufficient air for the starts without the need for top up from the compressors. Safety valves are
normally fitted to the air receivers but in some installations the reservoirs are protected against
overpressure by those of the compressors. There is a requirement that if the safety valves can be
isolated from the reservoirs, the latter must have fusible plugs fitted to release the air in the event of
fire. Reservoirs are designed, built and tested under similar regulations to those for boilers.
SHOW VIDEO OF How to Prepare and Start the Ship's Main Engine
Lesson 2: State precautions, safety measures, checking procedures and points to be made as
preparations before starting up main engine
The starting procedure of marine engines requires several points to be taken into consideration. While it is
necessary that none of these points should be missed, there are a few extremely important things that should
be done without fail while starting marine engines. Ten such important points are as followed:
1. Lubrication of Main Engine : Start pre-lubrication of the engine well before starting. For main engine it
should be started before 1 hour and for auxiliary 4-stroke engines at least 15 minutes in advanced.
2. Check All Parameters: After starting the lubrication pump, check lube oil levels and all other running pump
parameters such as cooling water pressure, fuel oil temp and pressure, control and starting air pressure etc. to
ensure that all are in the accepted range.
3. Open Indicator Cocks and Blow Through: All the indicator cocks of the marine engine must be opened up
for blow through of combustion chamber prior starting to avoid hydraulic damage because of water leakage
4. Rotate the Crankshaft: Rotate the crankshaft of the marine engine by means of turning gear so that all the
parts are thoroughly lubricated before starting.
5. Manual Check Turning Gear: Ensure that the turning gear is properly disengaged by checking it locally even
when the remote signal is showing-“disengaged” sign. Some auxiliary engines are provided with tommy bar
for rotation, ensure that it is removed from the fly wheel before the engine is started.
6. Check Jacket Cooling Water Temperature: The jacket cooling water temperature of the engine should be
maintained at at least 60 deg C for the main engine and 40 deg C for the auxiliary engine (it may vary
depending upon the KW rating of the engine).
7. Warm up the Engine: The incoming ship generator should be run at no load for at least 5 mins to allow
warming up of the system.
8. Put Load Sharing Switch to Manual: When 2nd generator is started, it will try to come on load as soon as
possible due to the auto load automation provided for sharing equal load (if same rated capacity). During
starting the 2nd generator, keep in mind to put the load sharing switch to manual. This will avoid the “just
started” generator to come on load, giving it some time for warm up.
9. Avoid Excessive Opening of Exhaust Valve: When starting main engine with hydraulic oil operated exhaust
valves, open the spring air first and then start the hydraulic oil to the exhaust valve. This will avoid excessive
opening of valves.
10. Examine the Engine: Responsible engineers of the ships to be present near the engine when it is started
from remote position. Auxiliary engine to be started from local position (avoid using remote start if possible).
Smooth starting and stopping of engines not only depends on systematic procedure but also on proper
maintenance overhauling procedures of marine engines.
Lesson 3: State the need for warming up/cooling down main engine or keeping it at hot
condition unless cooling down has been done
Before a large diesel is started it must be warmed through by circulating hot water through the jackets, etc.
This will enable the various engine parts to expand in relation to one another.
When any machinery cools down or heats up all the metal expands or contracts, this obvious causes the
clearances in the engine to change, as well as introducing a lot of thermal stress.
With regard to running the engine off load to cool it down, I would do this until the exhaust temperatures and
Jacket water outlet temperatures have stabilized . If the pistons, liners and heads have been running at high
power the combustion chamber surfaces will be very hot. If the engine is stopped the heat will continue to
flow into the cooling water and, if only a small preheating pump is running you could boil your jacket water.
Warming Through
Main engines are to be warmed through gradually following a stay in port or other occasion when they have
been shut down. The jacket water circulation temperature is to be raised over a period of time to as near to
the operating temperature as possible. The period of time is dependent on the jacket water temperature prior
to the commencement of circulation, the heating medium and size of main engine etc. As a general rule
circulation should commence not less than 12 hours before the estimated time of departure. Other circulating
systems are to be put on line during this period .Lubricating oil systems. Fuel circulating systems.
Lesson 4: Explain the standard of completing warming up/cooling down main engine
All circulating systems are to be as near as is possible normal operating parameters according to the manufacturer’s
instructions for the engine type. On vessels where the engine or engines are directly coupled to the propeller or
propellers. Mainly the Marine Main Engines are Water/Oil cooled. With the advancement in technology, the cooling
system is constantly being changed. Cooling of engines is achieved by circulating a cooling liquid around internal
passages within the engine. Jacket water cooling is used for cooling the liner and cylinder head .Piston cooling is done
using oil, though water is more efficient for removing heat but if mixed with Lubricating Oil, it contaminates the L.O.
Lesson 5: Explain precautions and typical procedures for warming up/cooling down main
engine including theoretical rationale.
1. Before a large diesel is started it must be warmed through by circulating hot water through the jackets, etc.
This will enable the various engine parts to expand in relation to one another.
2. The various supply tanks, filters, valves and drains are all to be checked.
3. The lubricating oil pumps and circulating water pumps are started and all the visible returns should be
observed.
4. All control equipment and alarms should be examined for correct operation.
5. The indicator cocks are opened, the turning gear engaged and the engine turned through several complete
revolutions. In this way any water which may have collected in the cylinders will be forced out.
6. The fuel oil system is checked and circulated with hot oil.
The length of time involved in these preparations will depend upon the size of the engine.
The starting air supply has to be closed as soon as possible after stopping the engine and open the venting
valve.
The indicator cocks in the cylinder head should be opened and the turning gear engaged.
For the post-lubrication of the cylinders, the crankshaft must be turned by the turning gear. During this the
cylinder lubrication must also be switched on for the same period.
a. Close the shut off valves from the starting air receiver.
b. Where possible, keep the cooling water warm in order to prevent the engine from cooling down too much.
The jacket cooling water pump should be kept running unless required to be stopped for maintenance work.
c. Turn the engine, at intervals, through several revolution with the indicator cocks open, using the turning
gear,(possibly done daily in dump climates.) Do this with the lubricating oil pump running and operating the
cylinder oil pumps at the same time. After completing this procedure ensure that the piston rest in a different
position each time.
Lesson 6: State precautions for starting associated auxiliaries to establish each system
constructing propulsion machinery such as fuel oil, lubricating oil, cooling system and
starting air system
a) Check the level of fuel oil tanks in the engine systems including the leakage drain tanks.
b) Check that all the shut-offs valves are in the correct position.
c) Check to ensure that all systems have been correctly vented
d) Check to ensure that cut-out devices for all the fuel injection pumps are correctly positioned for
normal fuel pump operation
e) Check that the fuel regulating linkage moves freely.
f) Check if the fuel control lever is back to the position REMOTE CONTROL
LUBRICATING OIL
COOLING SYSTEMS
a) The cooling water itself and the system should be checked periodically during service, preferably once
a week
b) Check possibility of seawater penetrating into cooling water.
c) Check the system which includes sea water, for example fresh water cooler cooled by sea water.
d) Check if cooling water is contaminated by exhaust gas by ph value.
e) Fill up the system with distilled water on the expansion tank.
a) Open the air supply to the shipboard system and from the starting air receivers to the control air supply.
b) Check the pressure in the starting air receivers and open the receiver drains until any condensate has
been completely drained.
c) Open the drain and test valve on the shut-off valve for starting air until all water has been drained.
d) Close venting valve at the shut-off valve for starting air and open the main shut-off valves on the
starting air receivers.
e) Turn the hand wheel on the shut-off valve for starting air until the pointer is at the AUTOMATIC
position. The pressure gauges on the pressure gauge panel should now indicate the following pressures:
• Safety control air and standby supply for air spring air on the pressure reducing valve 23HA –
6.0kg/cm2 • Air spring air supply on the pressure reducing valve 19HA – 7.5kg/cm2 • Control air
standby supply on the pressure reducing valve 19HB – 7.0kg/cm2
f) Open the test valve of the main automatic starting air shut-off valve for a short time and listen for the
valve opening which can be heard distinctly. Close the valve again
Lesson 7: State particularly, precautions against auxiliaries repair/overhaul was carried out.
Lesson 9: State the importance of carrying out all procedures in an orderly manner in order
to prevent malfunction and damage.
Sea trials of ships are carried out usually when the ship is newly constructed and delivered by the shipyard,
the ship management is transferred from one company to another, or major repairs have been performed
in the dry dock.
Sea trials is an extremely crucial time when the “seaworthiness” of the ship is checked by finding out errors in
the ship’s structure and machinery systems. If not properly planned and executed, sea trials can turn into
serious disasters leading to horrific consequences. Mentioned below are ten points that must be considered to
ensure smooth and safe sea trials:
Lesson 10: State the need to carry out main engine trial run and necessary precautions
Mentioned below are ten points that must be considered to ensure smooth and safe sea trials:
1.Only Experienced Personnel Should Handle Machinery Systems: If the sea trial is conducted for new ship/
purchased ship, the shipyard representative, designated captain or old crew should operate the ship’s
machinery and systems, whereas the new crew must understand the operations, fine points and problems
that can arise during sea trials.
2. Masters Must Take All Proper Permissions: The ship’s master should take all the necessary permissions and
port clearance for sea trails of the ship. Port inspector will then certify the vessel’s sea worthy for sea trials.
Port Pilot schedule and tugs are also booked for sea trials by the company. The ship’s crew should know and
understand the whole plan thoroughly.
3. Inform The Surveyor: Master must ensure that the surveyor is informed about the sea trial schedule and
he/she is present onboard during sea trials.
4. Workshop In-charges To Be Present On Ships: Chief engineer and master should ensure that the workshop
in-charges are present onboard to accompany for various machinery inspection repairs in the dry dock.
5. Sufficient Manpower for Inspection: A number of teams should be made on both deck and engine sides for
checking various system, overboard valves, water tight doors and access etc. when the ship is water borne
during sea trials.
6. Prepare a List of Overhauled Machinery: All the overboard valves/ structures and system which are
overhauled or opened in the dry dock must be listed and checked locally by ship’s staff for any water leakage.
Photocopies of the list must be presented to the ship’s staff to ensure that no machinery part is missed.
7. Check Alarms And Trips Are Working: Ensure that alarms and trips of all the machinery systems, including
main engine auxiliary engine, generator etc. are set back in working order
8. Ensure LSA and FFA are in Proper Working Condition: Before the ship goes out at sea, management officers
must ensure that all LSA and FFA equipment including fire and general alarms are in good operating condition
and the crew is ready to operate them during emergency.
9. Take Enough Evidence: Take as many photos or videos as possible while machinery and systems are being
tested during sea trials. This would serve as an important reference for future use.
10. Make Proper Checks Before Clearing Any Machinery: Ship’s master and chief engineer must ensure that
clearance for any system or machinery to be approved only when the operation of the same is satisfied by the
workshop, yard or shore in charge. Also, the ship’s engine (main and auxiliary engines) must be run at least 80
% of its maximum load for some time and its parameters to be noted before declaring it “OK”.
Lesson 11: State typical procedures for main engine trial run and checking points
Typical trials
• Sea trials are fairly standardized using technical bulletins published by ITTC, SNAME, BMT, regulatory
agencies or the owners. They involve demonstrations and tests of the ship's systems and performance
• Speed trial
• In a speed trial the vessel is ballasted or loaded to a predetermined draft and the propulsion machinery
is set to the contracted maximum service setting, usually some percentage of the machinery's
maximum continuous rating. The ship's heading is adjusted to have the wind and tide as close to bow-
on as possible. The vessel is allowed to come to speed and the speed is continuously recorded using
differential GPS. The trial will be executed with different speeds including service (design) and
maximum speed. The ship is then turned through 180° and the procedure is followed again. This
reduces the impact of wind and tide. The final "Trials Speed" is determined by averaging all of the
measured speeds during each of the runs. This process may be repeated in various sea states.
• Crash stop
• To test a crash stop, the vessel is ballasted or loaded to a predetermined draft and the propulsion
machinery is set to the contracted maximum service setting, usually some percentage of the
machinery's maximum continuous rating. The trial begins once the order to "Execute Crash Stop" is
given. At this point the propulsion machinery is set to full-astern and the helm is put hard-over to
either port or starboard. The speed, position and heading are continuously recorded using differential
GPS. The final time to stop (i.e.: ship speed is 0 knots) track line, drift (distance traveled perpendicular
to the original course) and advance (distance traveled along the original course line) are all calculated.
The trial may be repeated at various starting speeds.
• Endurance
• During endurance trials the vessel is ballasted or loaded to a predetermined draft and the propulsion
machinery is set to the contracted maximum service setting, usually some percentage of the
machinery's maximum continuous rating. The fuel flow, exhaust and cooling water temperatures and
ship's speed are all recorded.
• Maneuvering trials
• Maneuvering trials involve a number of trials to determine the maneuverability and directional stability
of the ship may be conducted. These include a direct and reverse spiral manoeuvres, zig-zag, and
lateral thruster use.
• Seakeeping
• Sea keeping trials were used exclusively for passenger ships but now used in a variety of vessels.
Involves measurements of ship motions in various sea states followed by a series of analyses to
determine comfort levels, likelihood of sea sickness and hull damage. Trials are usually protracted in
nature due to the unpredictability of finding the correct sea state and the need to conduct the trials at
various headings and speeds.
Lesson 12: State procedures for changing over the propulsion machinery to the state of navigation.
It is important to learn about the basics of the engine telegraph system before operating one (Read article).
However, most of the ships are now provided with a remote control for propulsion machinery and for
controlling the pitch of the propeller (for CPP type) as they are mainly operated in UMS mode. This gives the
ease to the navigation officer to control and maintain the speed and direction of the ship as per the
navigational condition and requirement.
The propulsion machinery order given from the bridge must be indicated in the engine control room and at
the local maneuvering platform. For having a control of propulsion machinery from navigational bridge, the
system must comply as per SOLAS chapter-II with the following requirements:
1. Starting and control of the speed must be provided and performed by single starting lever or a dedicated
push button switch.
2. Remote control is possible from only one location at a time, with indication as to which location is in control
both in navigational bridge and in engine control room.
3. The transfer of control must be possible from engine control room only.
8. Following indications of the propulsion plant must be displayed on the bridge along with the alarm for the
same:
• ME alarms
• Starting and control air.
• Direction of rotation.
• Pitch position (CPP system).
• R.P.M of the engine.
9. Alarm power to be automatically changed over to standby mode (batteries) in case of power failure of the
ship occurs.
Lesson 13: Explain the critical speed/revolution caused by torsional vibration of shafting
system.
Torsional vibrations are the characteristic of nearly all rotational machines and devices. However, torsional
vibrations of internal combustion engines and their shafting are especially significant. These vibrations appear
as the result of the variable revolution of rotating parts, invisible to the human eye.
Torsional vibrations are the consequence of a number of processes. The most common are:
The excitation of torsional vibrations is significantly determined by the piston's stroke and the mean effective
pressure. The ongoing increase of these characteristics is the cause of increased vibration excitation in the
recent propulsion plants.
The propulsion plant, composed of the propulsion engine, the shafting and the propeller, denotes a vibration
system. This system, determined by the inertia of its components, as well as by the stiffness between them,
possesses its own natural frequencies and corresponding modes of vibration.
The propulsion shafting, composed of the crankshaft, the intermediate shaft and the propeller shaft, will
vibrate when excited by variable torque.
The barred speed range must be passed through rapidly. Actually, torsional vibrations need some time to fully
develop and, if the barred speed range is passed sufficiently rapidly, there is a great possibility that the full
stress level will never be reached.
The barred speed range is clearly noted in red on the tachometer, as well as on notice boards. Moreover,
more recent propulsion plants are equipped with special devices that ensure that this range is rapidly passed.
Lesson 14 :Explain how the running conditions can be evaluated if it is in good working order
in terms of running parameters, engine performance and operating range.
• After superimposing the measured parameters on the performance curves, we come to know whether
the parameters are normal or abnormal. A complete study of the parameters helps us to pin point the
problem.
• All these parameters should be recorded as accurately as possible. Parameters can be evaluated in
such a way as temperatures, pressures and levels at normal range of every equipment that is necessary
for the normal operation of the ship/ship engine.
• In addition to the engine parameters recorded through, the additional parameters will be recorded on
the generator,
• Based on the results of the sea trial, additional parameters may need to be measured to diagnose and
correct installation issues.
• - Air inlet temp at the air cleaner: Air cleaner outlet temp. The hotter the inlet air the higher exhaust
temp is for a given power level. It’s important for overall engine life to keep the inlet air temp as low as
possible. A correctly designed ventilation system will keep the engine room within 15F/9C above
ambient, which in a pleasure craft can be difficult to achieve. Locate the temperature probes at the
same location on all the air cleaners (you should not install the probes in place of the air filter
restriction indicator).
• - Ambient seawater temperature: Seawater temperature at the time of test is important to
understand the ambient conditions during the test and evaluate the cooling system performance.
• - Exhaust backpressure: High backpressure may cause higher exhaust temperatures, which will cause
higher valve temp and reduce engine life.
• - Seawater inlet restriction: Raw water pump inlet pressure (for seawater cooled engines only).
• To determine the delivered power, the torque and rotational velocity of the propeller for a given speed
can be measured. This measurement can be carried out by the SVA onboard the ship with own
measurement equipment.
• The engine power estimation was attained through three alternative methods
• 1. engine rotational speed and torque measurement – on engine flywheel,
• 2. rotational speed and torque measurement – main propulsion shaft
• 3. engine mean indicated pressure measurement – each engine cylinder.
• The main engine performance has been recorded for further analysis that includes:
• – continuous engine output shaft torque speed profile,
• – engine cylinder pressure data,
• – engine fuel oil consumption, engine operational condition parameters.
Lesson 15 : Explain how running parameters such as temperatures, pressures and levels can
be determined in normal range.
There are standard pressures and temperature checks to be carried out by the watch keeping engineer, as he
gains experience these will become second nature; the various thermometers and pressure gauges being
scanned as he walks around the engine room checking the components. This means when a rouge value turns
up it is spotted right away either on the component or the engine control station instrument board. This is
situated just above the engine control station, either in the engine room or in the modern control room. The
board contains the pressure and temperature gauges for the main systems such as; exhaust temperatures,
jacket cooling and lube-oil pressure. We used an arrow to mark the optimum temperatures and pressures on
these gauges, and endeavor to maintain them; again any rouge value will show up instantly.
The board is located above the controls, being easily consulted from here. The other main gauges and
components that are easily reached are the engine room telegraph, rev-counter, air start reservoirs pressure
gauges and of course the controls themselves. Depending on the engine manufacturer, these consist of two
levers; left hand one usually air start, right hand lever; fuel control and are used when maneuvering.
The temperature of the HFO system must be kept at the recommended value to control its viscosity. This is
important as it must not turn "waxy" when being pumped through various heaters, the fuel pump and into the
injectors.
Lube-oil System
The temperature of the lube-oil must be carefully controlled through use of the lube-oil coolers seawater inlet
valve. Remember that as the temperature of the lube-oil rises the pressure drops. Conversely, a low lube –oil
temperature will increase the oil pressure. A sudden unexplained rise in temperature could signify a bearing in
the main engine running hot.
The pressure and temperature of the jacket water cooling also need close monitoring and maintained at
optimum values as the cooling water also supplies the turbo-blower air coolers. The pressure in this case is
controlled by the circ. pump, so any change could be a faulty pump, however, down to the pump or a loss of
pressure through a faulty cylinder liner rubber sealing ring, or even a cracked liner.
Temperature is another matter; this must be kept at the recommended value. Any rise could signify a
scavenge fire a rise in sea temperature or cooler problem.
The generators temperature and pressures are checked as per the main engine ones.
This leave the thrust block, prop shaft bearings, and stern gland. Here again the sense of touch should be used
as a guide to overheating, but there will be temperature gauges on the thrust and prop bearings along with oil
- level sight gauges.
Lesson 16: Explain what malfunctions are likely to occur due to running parameters getting
out of the normal range
• The power output depends on the size and design of the engine, but also on the speed at which it is
running and the load or torque.
• Multiply the torque by the engine speed. You will be using the formula (RPM * T) / 5252=HP, where
RPM is the engine speed, T is the torque, and 5,252 is radians per second. The first calculation you
want to do is multiply the torque and the engine speed.
The principal control device on any engine is the governor. It governs or controls the engine speed at some
fixed value while power output changes to meet demand. This is achieved by the governor automatically
adjusting the engine fuel pump settings to meet the desired load at the set speed.
Governors for diesel engines are usually made up of two systems: a speed sensing arrangement and a
hydraulic unit which operates on the fuel pumps to change the engine power output.
Mechanical governor
A flyweight assembly is used to detect engine speed. Two flyweights are fitted to a plate or ballhead which
rotates about a vertical axis driven by a gear wheel . The action of centrifugal force throws the weights
outwards; this lifts the vertical spindle and compresses the spring until an equilibrium situation is reached. The
equilibrium position or set speed may be changed by the speed selector which alters the spring compression.
As the engine speed increases the weights move outwards and raise the spindle; a speed decrease will lower
the spindle. The hydraulic unit is connected to this vertical spindle and acts as a power source to move the
engine fuel controls. A piston valve connected to the vertical spindle supplies or drains oil from the power
piston which moves the fuel controls depending upon the flyweight movement. If the engine speed increases
the vertical spindle rises, the piston valve rises and oil is drained from the power piston which results in a fuel
control movement. This reduces fuel supply to the engine and slows it down. It is, in effect, a proportional
controller .
Electric governor
The electric governor uses a combination of electrical and mechanical components in its operation. The speed
sensing device is a small magnetic pick-up coil. The rectified, or d.c., voltage signal is used in conjunction with
a desired or set speed signal to operate a hydraulic unit. This unit will then move the fuel controls in the
appropriate direction to control the engine speed.
• The power output depends on the size and design of the engine, but also on the speed at which it is
running and the load or torque.
• Shaft speed measurement is made with magnetic sensor, built in combined inductive head and a
frequency-voltage converter. The number of pulses are counted for a predetermined time and divided
into number pulses per revolution to find shaft rate of revolution.
• Speed trials are conducted at the end of ship construction usually at a limited time scale. It is rarely
possible to conduct the trials at contract conditions. Therefore, measured ship speed and shaft power
must be corrected for the differences between trial conditions and the contract conditions. Hence, ship
trials have uncertainties mainly due to following sources:
• - trial measurements: engine torque and shaft revolutions, and ship speed,
• - trial analysis: necessary corrections applied to trial results.
• Important parameters for a marine main diesel engine are the rating figures, usually stated as:
continuous service rating (CSR) and maximum continuous rating (MCR). The rating which is commonly
concerns is the maximum output at which the engine will operate continuously to maintain the desired
ship service speed - fully loaded. Basically, ship operators insist that the main engines be capable of
maintaining such speed, developed at approximately 80% of rated brake power. Normally a ship will
run sea trials to meet the contract trial ship speed and the engine continuous service rating should be
applied when the vessel is in service. For each type of engine, there is a maximum power limit outside
which the engine should not be run continuously.
• This means operation of an engine at standard maximum cylinder pressure for continuous service
rating, but at lower mean effective pressure and shaft speed. This can be achieved by altering the fuel
injection timing. The similar effect for NOx emission is used and lower emission level is available.
Controls to limit exhaust gas emissions which is tightening nationally, regionally and globally led to
complicated engine system control optimization, readily available for latest electronically controlled
engine.
Lesson 21: Explain in simple words, the difference of output characteristic between diesel
engine and steam turbine
STEAM TURBINES
The steam turbine is well suited to the largest power plants, produces a uniform turning effort, burns the least
expensive fuel, and is capable of relatively high efficiencies, long endurance, long life, long mean time
between overhaul (MTBO), and reasonable maintenance. It has the inherent disadvantages of large space
requirements, a large watch-standing force, slow response time, being slow in getting under way,
intermediate energy conversion with its secondary working substance, mechanical non-reversibility, and high
turbine speed. These latter two disadvantages necessitate a separate, low-efficiency astern turbine of reduced
power and large, heavy reduction gearing to the propeller shafts. The speed reduction is needed to allow both
the turbine and the propeller to operate in their most efficient speed range.
DIESEL ENGINES
The low-speed, direct-coupled diesel engine is the most efficient of all the marine power plants, with specific
fuel consumptions as low as 0.29 Ib/hp-hr. … it is being used to power most new merchant ships
The diesel engine has the highest thermal efficiency (engine efficiency) of any practical internal or external
combustion engine due to its very high expansion ratio and inherent lean burn which enables heat dissipation
by the excess air. A small efficiency loss is also avoided compared to two-stroke non-direct-injection gasoline
engines since unburned fuel is not present at valve overlap and therefore no fuel goes directly from the
intake/injection to the exhaust. Low-speed diesel engines (as used in ships and other applications where
overall engine weight is relatively unimportant) can have a thermal efficiency that exceeds 50%.
• Primary parameters
• Ship Track DGPS [Latitude, Longitude] or [m]
• Speed over the Ground DGPS Knots
• Shaft Torque or Shaft Power Torsion meter with strain gauges,Calibrated
• permanent torque sensor. Power to be calculated from torque and RPM [kNm], [kW]
• Shaft RPM Pick-up, laser counter, ship revs counter [Hz, RPM]
• Propeller pitch Bridge replicator
• Time GPS Time, Stopwatch [s]
• Water depth Ship echo sounder + nautical charts [m]
• Rudder angle Angular potential meter, string sensor, Ship rudder
• repeater[deg]
• Ship heading Gyro compass, or DGPS [deg]
• Relative wind Ship anemometer, external anemometer [m/s], knots, [deg]
• Wave height &
• Direction Wave measuring device (i.e. radar,scanner. etc), Wave buoy,
• Hind cast, observation by multiple observers [m], [deg]
• Draughts
• Physical observation and / or calibrated draught gauges
Lesson 23: State the importance of engine-room rounds to detect sign of faults/malfunctions, emphasizing
that running sound, leaking and vibration can be detected through engine-room rounds and these factors
cannot be detected with monitoring system.
• Engine watch keeping duties include monitoring the ship's dials and gauges that can indicate
malfunction needing immediate correction. Once any abnormalities re detected it the watcher must
notify proper personnel.
• Watch keeping is an integral part of marine engineer’s duties on board ship. A lot of maintenance work
can be reduced by following an efficient watch keeping routine in the ship’s engine room. Moreover, it
can also avoid serious accidents from taking place.
• A smooth running ship is a product of efficient handling at the bridge and effective management in the
engine room under any seagoing condition. When a marine engineer is approved to be the in charge of
the engine room, he is eligible and officially authorized to handle a ship’s engine of “Unlimited Power”.
It is therefore important that the watch keeping procedure, a daily routine that has to be carried out
every single day, is done in the most systematic manner to prevent any kind of breakdown.
12 ways which will help a marine engine on board ship to master the watch keeping procedure.
• 1. Knowledge is the Base: The first and most important step to enhance your duties during a watch is
to have a very strong knowledge base. One must know the basics of the machines and their operations,
new trends and upcoming technologies, and maritime regulations along with their amendments.
• Knowledge gives a great boost to engineer’s confidence level and also results in more accurate job
decisions. Engine room operation also requires information from other domains of engineering such as
mechanical, hydraulic, pneumatic, electrical and electronic systems, refrigeration etc. Knowing these
fundamentals makes an engineer’s foundation stronger.
• 2. Follow Your Instincts: It is commonly said on ships that in order to become a good watch keeper, an
engineer must use all the 6 senses- i.e. touch, hearing, smell, visuals, taste and kinaesthetic senses (6th
Sense). All these senses when applied correctly help an engineer to understand the condition of
machines in a better way.
• Touch: Feeling a machine for its temperature can tell you about the condition inside the machinery,
for e.g. High temperature means something wrong.
• Hearing: It is always advisable to keep a track of sounds coming from different machines in the engine
room as any abnormality would result in change of the sound.
• Smell: Another powerful sense that helps to determine a problem is -smell. Burning of parts or
accessories due to increase in temperature, oil leakage, chemicals etc. can be easily identified using
this sense.
• Taste: Your tongue can identify different tastes; and you can apply this characteristic to your watch
keeping routines, for e.g. Tasting can help to identify the difference between sea water and fresh
water as both of them are used as prime mediums for cooling on ships.
• Visual: The most commonly used sense of all is the power of visualisation, helpful in identifying engine
room and machinery conditions. Whenever you enter the engine room you must start looking for any
kind of visual abnormality.
• 6th Sense: Considered to be the most powerful of all senses, your inner feeling (gut feeling) can
sometimes prove to be a lifesaver during watch keeping. Listen to it when you feel there is something
wrong in the engine room. However, don’t rely on it blindly; back it up with proper procedures.
• 3. Go By The Book: Every Engine room is provided with hundreds of documents – Manuals, operating
instruction, and safety and pollution prevention instructions just to name a few. Follow them
religiously during your watch keeping procedures.
• 4. Interpreting log book: A smart engineer would know the importance of engine room log book and
would also know how to interpret previous readings of different machines from the same. Interpreting
log means keeping a track of previous records of machinery parameters from the log book and using
them to analyse the present situation or to identify a problem.
• 5. Clear Communication: Efficient communication between maritime professionals is an important
factor for a safe and efficient operation onboard. If you are a watch keeper, you must clearly
communicate all kinds of operations and problems/ suspicions with your seniors and crew members.
An efficient engine room-bridge communication is also very important to make sure that navigational
officers at the bridge can plan their procedures or stay prepared for any kind of situation.
• 6. Take a Complete Round, Don’t Skip Any Machinery: Automation and alarm systems of machines are
always helpful in detecting early stage faults; however, it is a known fact that human vigilance is more
capable of detecting and interpreting errors more accurately. When on engine room round, all
machines on all levels must be examined for proper operation. Moreover, also make sure that you
note your findings in the log book for future reference.
• 7. Never Neglect Any Alarm: Alarm systems in the engine room are indication or pre warning of any
abnormality in the engine room machines. Sometimes due to a technical glitch such as connection or
electronic fault, an alarm would become faulty and give out audio and visual warnings after every few
minutes.
• This generates a habit among watch keepers to ignore the alarm totally and to cancel it from the
control room. However, make sure that you are able to differentiate between the faulty and normal
alarm, and also keep a track on the repairing work of faulty alarm so that you are aware when it is back
to normal condition.
• 8. Do Not Hide Faults: If you see any kind of fault while taking rounds or have committed a mistake,
never try to hide it. Remember that even the smallest fault can become dangerous if unattended at the
correct time. Always report the incident to your superiors and try to remove or repair the fault as soon
as possible.
• 9. Call for Help When in Need: In an engine room having hundreds of machines, faults are bound to
happen. Sometimes you may feel that the fault is big and a single person won’t be able to handle it
alone. In such situations, don’t hesitate to ask for help. Ship operation is all about team work and you
should respect that and know its importance.
• 10. Obey Orders: A good watch keeper must follow eligible orders from seniors, who have better
experience and understanding of machines. However, a smart watch keeper should also use his/her
own judgement when the need arises. Take inputs and advices from your seniors, but be confident
while carrying out your duties.
• 11. Follow Alcohol Policy: Never ever commence or carry out your watch under the influence of
alcohol, as it may interfere with your decision making abilities. Always follow your company alcohol
policy. In case you are under influence of alcohol, don’t be ashamed to inform your seniors.
• 12. Avoid Fatigue: Fatigue is the biggest reason behind human mistakes on ship. Always take proper
rest in your free time and avoid working when tired. Though this is tough to follow most of the time,
ask your seniors for a brief break so that you can freshen up and get back to work with more energy
and enthusiasm.
Lesson 24: Describe how to carry out the cleaning of turbocharger under way.
The Blower side of turbocharger is cleaned by fresh water. The engine is run at its full load rpm to achieve best
possible cleaning. A container is fitted with an inlet line coming from the blower discharge side and the outlet
line from the container or cylinder goes for washing blower side.
When the valve in the inlet of cylinder or container is opened, compressed air carry water with pressure and
the kinetic energy of water cleans the blower.
The Cleaning of the Turbine side and blower side is carried out at regular interval of time to remove carbon,
soot, and other exhaust deposits. The cleaning of turbocharger is carried out when the engine is running.
1) Water Washing
In this method, the engine speed is reduced until the temperature of the exhaust inlet falls below 420 °C.
Fresh Water used for washing must be slightly hot and the water is injected through a regulating valve
connected to the the turbine side. This is done to avoid thermal shock to the machinery.
While performing water washing the drain is kept open. When the water feed is closed the drain is observed
until no water comes out.
The engine is run for further 20 minutes with less rpm to dry out the turbine from water. Before increasing the
rpm, drain is shut and any abnormal vibration must be observed.
2) Dry Washing
For Dry washing carbon granules are used which are injected inside the turbine through compressed air
system.
The engine speed is not reduced as there is no risk of thermal stresses in dry washing.
Lesson 25:Explain how to keep running of main diesel engine condition of cutting fuel oil to
one cylinder or more.
• If immediate repair is not possible, the engine can be operated with one or more cylinders or
turbochargers out of operation, but with reduced speed owing to the following:
• As, in such cases, the air supply is no longer optimal, the thermal load will be higher. Therefore,
depending upon the actual circumstances, the engine will have to be operated according to the
restrictions mentioned in operating manual of the engine.
•Pressure pulsations may occur in the scavenge and exhaust receivers, which can give a reduced air
supply to any one of the cylinders, and as a result cause the respective exhaust temperatures to
increase. The fuel pump index for these cylinders must therefore be reduced to keep the exhaust
temperatures (after valves) within prescribed limits.
•Since the turbochargers will be working outside their normal range, surging may occur. This can
generally be remedied by “blowing off” from the scavenge air receiver.
•If more than one cylinder must be cut out of operation, and the engine has two or more
turbochargers, it may be advantageous to cut out one of the turbochargers.
•When cylinders are out of operation, governor hunting may occur. When this happens, the fuel pump
index must be limited by operating the electric governor on “index control”.
• With one or more cylinders out of operation, torsional vibrations, as well as other mechanical
vibrations, may occur at certain engine speeds. Should unusual noise or extreme vibrations
occur at the chosen speed, the speed must be further reduced.
•If the engine is to be run for a prolonged period with cylinders out of operation, the engine builder should
always be contacted in order to obtain advice concerning possible recommended barred speed ranges.
Lesson 26: Explain how to keep running of main diesel engine under the condition of
reducing the number of turbochargers.
How will you run engine in case of turbocharger failure ?
1.Rotor to be blocked
2.Exhaust gas to be by-passed the turbocharger
3.Run engine with reduced speed with remaining turbocharger
4.Use Auxiliary Blowe5. Maintain all temperature and pressure of fuel, cooling water and
lubrication within limit
How to Cut off Damaged Turbochargers for Engine Operation
Engines with one turbocharger (Engines with exhaust by-pass)
1.Stop the engine.
2.Lock the turbocharger rotor.
4.Remove the compensator between the compressor outlet and the scavenge air duct. This reduces
the suction resistance.
5.Run engine with 15% of MCR load and 53% speed.
Engines with one turbocharger (Engines without exhaust by-pass)
1.Stop the engine.
2.Remove the rotor and nozzle ring of the turbocharger.
3.Insert blanking plates.
4.Remove the compensator between the compressor outlet and the scavenge air duct. This reduces
the suction resistance.
5.Run engine with 15% of MCR load and 53% speed.
Engines with two or more turbochargers
1.Stop the engine.
2.Lock the rotor of the defective turbocharger.
3.Insert orifice plates in the compressor outlet and the turbine inlet. (A small air flow is required to
cool the impeller, and a small gas flow is desirable to prevent corrosion)
4.Run engine with 20% of MCR load and 58% speed
Lesson 27:Describe the conditions which create dangerous oil mists in crankcases.
Lesson 28:Describe the correct action to take when hazardous conditions are indicated in a
crankcase.
• 1. Crankcase compartment explosions, a dangerous event, and its prevention through the interruption
of the formation of oil mist
• The best method is the early recognition of the emergence of a hot spot and the interruption of the
growth of the hot spot through suitable measures (motor stop). Not only is the danger of a crankcase
compartment explosion eliminated, but catastrophic parts failure is greatly reduced and perhaps also
eliminated.
• 2. Prevention of a crankcase compartment explosion through vacuum elimination of the crankcase
atmosphere
• This route is taken in the case of high speed light craft (HSLC) engines, by replacing the atmosphere in
the crankcase compartment quickly enough through the constant removal by a vacuum.
• While doing so, the detection of oil mist is not being used as an indicator system for preventing
damage
• 3. Inert gas, a further method for the prevention of crankcase compartment explosions
• reduction of oxygen in the atmosphere of the crankcase compartment by mixing in nitrogen or carbon
dioxide. This would be done to the extent that a capability for the oil mist to be ignited no longer exists
• 4.Solely monitoring the bearing temperatures cannot be a replacement for the detection of oil mist
• The monitoring of only the bearing temperatures cannot be a replacement for a detection of oil mist,
especially if it is restricted to the main bearing as the supposed main place for the development of oil
mist.
Lesson 29: Explain the importance of keeping scavenge air spaces and supercharge air-
spaces drained and clean
• To prevent carbonized lube oil, unburnt fuel oil and carbon from the residual products of the
combustion spaces are accumulated in the scavenge spaces with the running of the engine. Under
certain faulty running condition of the engine, these may ignite causing a fire in the enclosed
scavenge space, known as scavenge fire.
Lesson 30: Describe the correct procedure and actions to take if a fire occurs in the scavenge
air space or in the supercharge air space when an engine is running.
• Once a scavenge fire starts, hit the engine room emergency button, reduce the engine to its slowest
possible revolutions this will limit the amount of fuel oil being admitted to the cylinders. It will also
reduce the amount of combustion air to the cylinders, lowering the oxygen content being supplied to
the scavenge fire.
• The fuel must be isolated to the cylinder in which the fire is occurring by lifting the relative fuel pump
plunger clear of the operating cam. The bridge should be informed and the engine room telegraph put
to dead slow ahead, recording the times and the movements in the log book for future reference.
• The watch keepers The senior engineer should remain at the controls, junior engineer adjusts the
seawater to the lube oil and jacket coolers maintaining operating temperatures.
• Other Engineers The rest of engineers should operate scavenge CO2 or mist sprays if fitted, Isolate the
fuel by lifting the pump piston rod of the offending cylinders fuel pump cam, increases lube oil to that
cylinder by hand operating the lubricator to prevent the piston seizing and, keep an eye on the exhaust
condition out of the flu, scavenge door temperature and drains to sludge tank. Once the greasers have
cleaned out the scavenge space, the senior engineer should inspect the piston rod and gland for signs
of excessive scorching. The gland may need stripping if the springs holding the scraping rings have lost
their tension through heat from the burning oil; excessive oil usually accumulating around this area.
Excessive scorching will be evident by the blue color of the gland top keep ring and set screws.
• Engine room Greasers - Once it has been determined that the fire has been extinguished, and the
scavenge space has cooled enough for cleaning, the scavenge inspection doors should be slowly and
carefully removed. The resultant carbon residue and fuel oil can now scraped away then cleaned using
rags leaving the space dry and clean. The exhaust gas boiler should be fired up to maintain boiler
steam pressure and the offending cylinder lube oil reservoir kept topped up.
Course outline:
FINAL
6. Auxiliary Prime Movers and Associated Systems (Steam Turbine)
7. Propeller and load diagrams
8. Characteristics Gas Turbines
MODULE 3 (Week 13-18) 30 HRS.
Lesson 1: State precautions before starting a steam turbine such as confirming steam line,
gland steam line, lubricating oil line, condensate water line and circulating line.
• System checks include the following where applicable: Pumps checked for power on, charged and
vented freedom of movement, cooling water supplies, guards in place, valves set. Check all Valves and
flanged joints for leaks. Coolers check for charged and vented. Filters and strainers cleaned, check for
charged and vented. Heaters check for charged and vented, when on load check water level controls
are operating.
• When plant is in service the following checks should be made, pressure, differential pressures, where
applicable, temperature, noise, vibration, flow, checks for leaks, check level control systems are
operating correctly.
Rotor: consist of HP, and LP pressure stage blades, shaft and governor pedestal components, thrust bearing,
journal bearing, Turning gear and main lube-oil system.
1. Turbine Casings
The casing shape and construction details depend on whether it is a High Pressure (HP) or Low Pressure (LP)
casings. For low and moderate inlet steam pressure up to 120 bar, a single shell casing is used. With a rise in
inlet pressure the casing thickness as to be increasing. Handling such heavy casing is very difficult also the
turbine as to slowly brought up to the operation temperature.
2. Turbine Rotors
The steam turbine rotors must be designed with the most care as it is mostly the highly stressed component in
the turbine. The design of a turbine rotor depends on the operating principle of the turbine.
• The impulse turbine, in which the pressure drops across the stationary blades. The stationary blades are
mounted in the diaphragm and the moving blades fixed or forged on the rotor. Steam leakage is in
between the stationary blades and the rotor. The leakage rate is controlled by labyrinth seals. This
construction requires a disc rotor.
• The reaction turbine has pressure drops across the moving as well as across the stationary blades. The disc
rotor would create a large axial thrust across each disc. Hence disc rotors are not used in the reaction
turbine.
Initially, the reaction turbines rotors are made by solid forged drum-type rotor. The rotors are heavy and rigid
construction. Due to this, the inertia of the rotor is very high when compare with the disc-type rotor of the
same capacity. To overcome this nowadays the hollow drum-type rotors are used instead of solid rigid rotors.
Usually, this type of rotor is made of two pieces construction. In some special cases, the rotor is made up of
multi-piece construction.
3. Turbine Blades
The efficiency of the turbine depends on more than anything else on the design of the turbine blades. The
impulse blades must be designed to convert the kinetic energy of the steam into mechanical energy.
Blade Fastening
After turbine blades are machined through the milling process. Then the blades are inserted in the rotor
groove. Depend upon the application the blade root section varies
Twisted Blades
This type of blades is used in the last stage of a large multistage steam turbine. These are the largest blade in
turbine and contribute around 10% of the turbine total output. Due to larger in size, these types of blades are
subjected to high centrifugal and bending forces. To overcome these forces twisted construction is used.
5. Shrouds
Shrouds are used to reinforce the turbine blades free ends to reduce vibration and leakage. This is done by
reverting a flat end over the blades refer figure. In some cases especially at the early stages, the shroud may
be integral with the blade.
The first turning gears turned the shaft at approximately 20 rev/mm, later increased to 40 and up to 60
rev/mm as proper lubrication is difficult to obtain at low speed; the same goes for the hydrogen seals of
generators. Some turning gears, electric or hydraulic, turn the shaft 1 800 at set times over a period of 24
hours.
Before a cold turbine is started up it should be on the barring gear for approximately three hours. When a
turbine is shut down, it should be barring for the next 24 hours. If a hydrogen-cooled generator is involved the
turbine should be kept on barring gear to prevent excessive loss of hydrogen.
Turbine Bearings
One of the steam turbine basic part is bearing. They are two types of bearings used based on the type of load
act on them
• Radial Bearing
• Thrust Bearing
Radial Bearings
For small turbines mostly equipped with anti-friction type bearings. Widely used anti-friction bearings are the
self-aligning spherical ball or roller bearing with flooded type lubrication is used.
In the case of medium turbines used plain journal bearing. They may be ring lubricated sleeve bearings with
bronze or Babbitt lining. Both flooded and force types are employed.
For larger turbines, the radial bearing will be a tilting pad type. The number of pad per bearing will be selected
based on the weight of the rotor. For these types of bearing forced lubrication is used.
Thrust Bearings
The main two purposes of the thrust bearing are:
The thrust bearing is located on the free end of the rotor or we can say at the steam inlet of the turbine. The
axial thrust force is very small for impulse turbines. This is due to the presence of pressure equalizing holes in
the rotor discs to balance the thrust force generated across the disc. A simple thrust bearing such as a ball
bearing for small turbines and radial Babbitt facing on journal bearings are commonly used in small and
medium-size turbines. Tilling pad type thrust bearings are used in the large steam turbines.
7. Turbine Seals
Seals are used to reduce the leakage of steam between the rotary and stationary parts of the steam turbine.
Depend upon the location of seal, the seals are classified as two types, they are
• Shaft Seal
• Blade Seal
Shaft Seals
Shaft seals are used to prevent the steam leakage where the shafts extend through the casing. In the case of a
small turbine carbon rings are used as shaft seal up to the surface speed of the shaft is 50m/s. The carbon ring
is made up of three segments butting together tightly under the pressure of a garter spring. The carbon rings
are free floating in the housing and an anti-rotating pin is used to prevent the rotation of carbon ring seal.
Due to the self-lubrication properties of the carbon rings, they maintain a close clearance with the shaft.
Blade Seals
Blade seals are used to prevent the steam leakage between the diaphragm and the shaft. The efficiency of the
turbine depends largely on the blade seals. Labyrinth seals are used as blade seals in the small and large
turbines. In the case of large steam turbine spring loaded labyrinth seals are used.
8. Turbine Couplings
The purpose of couplings is to transmit power from the prime mover to the driven piece of machinery. Flexible
type couplings are used in turbines. The coupling hubs are taper bore and key way to fit the tapered end of
the shaft.
9. Governor
The governor is one of the steam turbine basic parts. Its main function is to control the operation of a steam
turbine. Generally, the governor is classified as two type
• Speed-sensing governor
• Pressure sensing or load governor
• Mechanical Governor
• Hydro-mechanical Governor
• Electronic Governor
In the case of small turbine Oil relay type (Hydro-mechanical) governor NEMA class “A” is used. For the larger
turbine, electronic governor NEMA class “D” is used.
• The correct procedure ensures that no part of the machinery goes through any kind of stress- thermal
or mechanical. It also helps the ship to operate without wasting any extra time.
• The correct starting procedure for steam Turbine Generator onboard ship is as follows:
• Check turbo generator lube oil sump level and drain it for water. Replenish it if level is less than
normal.
• Start the lube oil priming pump from the local station and check the lube oil pressure. Put the priming
pump on auto.
• Check and fill up the Turbine Generator vacuum pump operating water tank to normal level.
• Check vacuum condenser condensate level from the condensate pump. Put the pump on auto so that
the level is maintained all the time.
• Operate the steam drain valve to drain any condensed water from the steam line to avoid excessive
hammering and vibration while starting turbo generator.
• Open the main steam inlet valve for turbo generator.
• Adjust the gland steam pressure to normal level.
• Check and open the sea water valves for vacuum pump cooler, T/G lube oil cooler and vacuum
condenser are opened.
• Start the vacuum pump and bring up the vacuum in the condenser.
• Open condensate pump valves and switch on the pump.
• Check whether the condensate vacuum, gland steam pressure, steam inlet pressure, and lube oil
pressure are normal.
• Start turbo generator from the local station and close the drain in the steam line.
• Check first and second stage steam pressure.
• Check condenser vacuum and water level.
• Check lube oil pressure and vibration levels.
• Check turbo generator speed, voltage, frequency, vacuum, condenser level and other parameters.
• Give control to remote station from the local control and take the TG on load.
Lesson 4: Describe briefly the control system and its components including their function.
The modern digital turbine control system (TCS) is designed to control the main steam flow to the steam
turbine in all operational conditions by means of the turbine throttle, governor, admission, and or extraction
control valves. The control functions are conducted through the use of simplex or redundant electronic
functions incorporated within the TCS software and hardware, integrated through the use of servo coil
actuators.
Master controllers automatically engage when required to ensure the appropriate rates of change match the
mode of operation of the turbine. Set point controls, open and closed-loop control functions, as well as
continuous monitoring functions associated with the TCS system prevent the turbine generator from assuming
inadmissible operating conditions.
The principle features of the turbine control system (TCS )system are summarized as follows:
• Speed Control- The speed control function provides the operational control involving the speed limiting
and acceleration functions of the unit over the entire operating speed range. The speed control system is fully
integrated with the load rejection and load anticipatory functions as required, as well as the turbine trip
system.
• Inlet/Admission Pressure Control-two channel selection which facilitates initial pressure (boiler follow
mode) and limit pressure (turbine follow mode) functions- The inlet/admission pressure control provides two
channel selection which facilitates initial pressure (boiler follow mode) and limit pressure (turbine follow
mode) functions. This automatic control function is activated when the inlet-steam pressure drops to a pre-
determined configurable set point.
• Load Control-via either a load set point command from a DCS, or can be configured to receive MW input
for utilization of the load control function developed within the system, or can be configured stand-alone as a
MW or Speed Droop function
• Frequency Influence- When the generator is on the grid and the turbine controller is in the “load”
control mode, the speed control function continues to provide a speed error (influence) input for use in
frequency regulation
• ADS (Automatic Dispatch System) Influence- The TCS system is designed to accept influencing from
an ADS controller, facilitating the remote dispatch loading and unloading of the machine along predetermined
ramp gradients. The load limit gradients are configurable through the entire range of operation via password
protection.
• Valve Lift Control- The valve lift controller integrates the min-gated valve demand reference versus valve
actual (setpoint) functions. Some vendors have standard applications oversampling rates of greater than 20
samples per cyclic event throughout the stroke of the valve to achieve the fastest possible response time.
• All main and auxiliary turbines are to be provided with over speed protective devices to prevent the design
speed from being exceeded by more than 15%.
• Arrangement is to be provided for shutting off the steam to the main turbines by suitable hand trip gear
situated at the maneuvering stand and at the turbine itself.
Hand tripping for auxiliary turbines is to be arranged in the vicinity of the turbine over speed protective
device.
• Where the main turbine installation incorporates a reverse gear, electric transmission, controllable pitch
propeller or other free-coupling arrangement, a separate speed governor in addition to the overspeed
protective device is to be fitted and is to be capable of controlling the speed of the unloaded turbine
without bringing the overspeed protective device into action.
• Where exhaust steam from auxiliary systems is led to the main turbine it is to be cut off at activation of the
overspeed protective device.
• Auxiliary turbines driving electric generators are to have both:
a speed governor which, with fixed setting, is to control the speed within the limit of 10% for momentary
variation and 5% permanent variation when the full load is suddenly taken off, and an over speed protective
device which is to be independent of speed governor, and is to prevent the design speed from being exceeded
by more than 15% when the full load is suddenly taken off.
• Main ahead turbines are to be provided with a quick acting device which will automatically shut off the
steam supply in the case of dangerous lowering of oil pressure in the bearing lubricating system. Where
deemed necessary by the Classification Society appropriate means are to be provided to protect the
turbines in case of:
1. abnormal axial rotor displacement,
2. excessive condenser pressure,
3. high condensate level.
• Auxiliary turbines having governors operated other than hydraulically in which the lubricating oil is
inherent in the system, are to be provided with an alarm device and a means of shutting off the steam
supply in the case of lowering of oil pressure in the bearing lubricating oil system.
• Main turbines are to be provided with a satisfactory emergency supply of lubricating oil which will
come into use automatically when the pressure drops below a predetermined value.
• To provide a warning to personnel in the vicinity of the exhaust end steam turbines of excessive
pressure, a sentinel valve or equivalent is to be provided at the exhaust end of all turbines.
• Non-return valves, or other approved means which will prevent steam and water returning to the
turbines, are to be fitted in bled steam connections.
• Efficient steam strainers are to be provided close to the inlets to ahead and astern high pressure
turbines or alternatively at the inlets to maneuvering valves.
• All vessels are to be fitted with means for detecting a rise of water in the machinery space bilges or
bilge wells. Bilge wells are to be large enough to accommodate normal drainage during the unattended
period.
• Where the bilge pumps start automatically, means shall be provided to indicate if the influx of liquid is
greater than the pump capacity or if the pump is operating more frequently than would normally be
expected.
The centerline of the crankshaft must be along the centerline of the propulsion shaft, and the propeller. If that
fails, the propeller will wobble about its position during running condition.
The initial calculation is to determine the load on each bearing, assuming all bearings to be in a straight line.
The computer programmed then simulates the raising of each bearing through a range and calculates, for
each small change, the increase of its own load and alteration in load on each of the other bearings.
Shaft checks
Propeller shaft, tail shaft – The aftermost section of the propulsion shafting in the stern tube in single screw
ships and in the struts of multiple screw ships to which the propeller is fitted. Propulsion shafting constitutes a
system of revolving rods that transmit power and motion from the main drive to the propeller.
Shaft bearings
Shaft bearings: The intermediate shafting between the tail shaft and main engine, gearbox or thrust block may
be supported in plain, tilting pad or roller bearings. The two former types usually have individual oil sumps,
the oil being circulated by a collar and scraper device; roller bearings are grease lubricated.
• Plain Bearing
Any oil between a static shaft and plain journal bearing in which it rests, tends to be squeezed out so that
there is metal to metal contact. At the start of the rotation the journal is inclined to roll up the bearing surface
against the direction of rotation until friction slip occurs. Then, provided there is oil in the clearance space, this
will cling to the moving surface and be dragged between the shaft and the bearing.
Replacement of the ineffective side portions of the journal by pads capable of carrying load will considerably
increase its capacity. Tilting pads based on those developed by Michell for thrust blocks are used for the
purpose.
•Roller bearing
Roller bearings are supplied in sizes to suit shafts up to the largest diameter. Flange couplings dictate that
roller bearing races must be in two parts for fitting. The section of the shaft where the split roller bearing is to
be fitted, must be machined very accurately and with good finish. The two halves of the inner and outer races
are fitted and held with clamping rings where fitted, are grease-lubricated.
Coupling bolts
The elongation of a bolt when tightened, causes a reduction in cross sectional area. The relationship between
change in length and the change of cross sectional area is summarized by Poisson's Ratio. In a clearance bolt,
this is not a problem, but with a normal fitted bolt, positive contact between the accurately machined bolt and
the reamered hole is lost when the bolt is tightened.
Stern tube
The stern tube, as the name suggests, is a hollow tube-like structure at the stern or rear part of the ship. A
ship needs a propeller to drive it forward against the waves. The propeller, located outside the ship, needs to
be connected to the engine inside the ship’s engine room.
2. Lip seals, in which a number of flexible membranes in contact with the shaft, prevent the passage of fluid
along the shaft.
3. Radial face seals, in which a wear-resistant face fitted radially around the shaft, is in contact with similar
faces fitted to the after bulkhead and to the after end of the stern tube.
Fixed Pitch propeller
The propeller is designed in a way such that, if you cut the propeller radially at any random radius from its
center, then the cut section of the propeller blades will have a certain pitch.
keyless propeller
The keyless propeller depends on the accuracy of the hub and shaft tapers and correct grip from the
stretched propeller hub on the shaft. The degree of stretch is controlled by push up. It must ensure adequate
grip despite any temperature changes and consequent differential expansion of bronze hub and steel shaft.
Flexible coupling
Where a gearbox is fitted, a torsionally flexible coupling is necessary between the medium-speed diesel and
the reduction gear. The coupling is necessary because the periodic application and reduction of torque as
engine cylinders fire in turn, tends to result in alternate loading and unloading of the gear teeth. The torsional
vibration effect is sufficient to cause serious gear tooth damage.
Lesson 1: Explain the following with the aid of sketches where applicable:
• Propeller curve
• Propeller design point
• Fouled hull, sea margin and heavy propeller
• Constant ship speed lines
• Propeller curve
Ship moves forward with some velocity when the necessary propeller thrust (T) is greater than the pertaining
resistance. The thrust of a propeller depends on its size, angle of attack of its blades, and the speed at which it
spins. By convention, propellers are described by diameter and pitch in that order. The diameter of propeller is
governed by its speed of rotation and the power of the engine rotating it.
Normally, estimates of the necessary propeller power and speed are based on theoretical calculations for
loaded ship, and often experimental tank tests, both assuming optimum operating conditions, a clean hull and
good weather. The combination of speed and power obtained may be called the ship’s propeller design point
placed on the light running propeller curve
When the ship has sailed for some time, the hull and propeller become fouled and the hull’s resistance will
increase. Consequently, the ship speed will be reduced unless the engine delivers more power to the propeller
the propeller will be further loaded and will be heavy running .
Sea margin at heavy weather
If, at the same time the weather is bad, with head winds, the ship’s resistance may increase compared to
operating at calm weather conditions. When determining the necessary engine power, it is therefore normal
practice to add an extra power margin, the so-called sea margin, which is traditionally about 15% of the
propeller design power.
When determining the necessary engine speed considering the influence of a heavy running propeller for
operating at large extra ship resistance, it is recommended - compared to the clean hull and calm weather
propeller.
The constant ship speed lines. These lines indicate the power required at various propeller speeds to keep the
same ship speed provided that the optimum propeller diameter with an optimum pitch diameter ratio is used
at any given speed, taking into consideration the total propulsion efficiency.
Lesson 1: Explain the following with the aid of sketches where applicable:
In order to achieve accuracy, the fuel consumption and power developed is always measured over a suitable
time period on a good
Effective Engine Power, Po - Say 8,130 bhp (Engine power is calculated from the performance sheet. It can
be calculated from the Indicator diagram or with fuel pump index method.
h x Pe
• Brayton cycle
• Thermal efficiency of Brayton cycle
• Heat balance of marine gas turbine plant
Brayton cycle
The Brayton cycle is a thermodynamic cycle named after George Brayton that describes the workings of a
constant-pressure heat engine. The original Brayton engines used a piston compressor and piston expander,
but more modern gas turbine engines and air breathing jet engines also follow the Brayton cycle.
Although the cycle is usually run as an open system (and indeed must be run as such if internal combustion is
used), it is conventionally assumed for the purposes of thermodynamic analysis that the exhaust gases are
reused in the intake, enabling analysis as a closed system.
Gas-turbines usually operate on an open cycle, shown up.A compressor takes in fresh ambient air (state 1),
compresses it to a higher temperature and pressure (state 2).Fuel and the higher pressure air from
compressor are sent to a combustion chamber, where fuel is burned at constant pressure. The resulting high
temperature gases are sent to a turbine (state 3).The high temperature gases expand to the ambient pressure
(state 4) in the turbine and produce power.The exhaust gases leave the turbine.Part of the work generated by
the turbine is sent to drive the compressor. The fraction of the turbine work used to drive the compressor is
called the back work ratio.
Since fresh air enters the compressor at the beginning and exhaust are thrown out at the end, this cycle is an
open cycle.
By utilizing the air-standard assumptions, replacing the combustion process by a constant pressure heat
addition process, and replacing the exhaust discharging process by a constant pressure heat rejection process,
the open cycle described above can be modeled as a closed cycle, called ideal Brayton cycle. The ideal Brayton
cycle is made up of four internally reversible processes.
• isentropic compression – ambient air is drawn into the compressor, where it is pressurized (1 → 2).
The work required for the compressor is given by WC = H2 – H1.
• isobaric heat addition – the compressed air then runs through a combustion chamber, where fuel is
burned and air or another medium is heated (2 → 3). It is a constant-pressure process, since the
chamber is open to flow in and out. The net heat added is given by Qadd = H3 - H2
• isentropic expansion – the heated, pressurized air then expands on turbine, gives up its energy. The
work done by turbine is given by WT = H4 – H3
• isobaric heat rejection – the residual heat must be rejected in order to close the cycle. The net heat
rejected is given by Qre = H4 - H1
As can be seen, we can describe and calculate ( thermodynamic efficiency) such cycles (similarly for Rankine
cycle) using enthalpies.
To calculate the thermal efficiency of the Brayton cycle (single compressor and single turbine) engineers use
the first law of thermodynamics in terms of enthalpy rather than in terms of internal energy.
dH = dQ + Vdp
➢ Heat balance of marine gas turbine plant
Gas turbine heat balance analysis uses plant measured data as input, and solves conservation of mass and
energy plus chemical combustion equations to yield additional information about the current state of the gas
turbine. The calculated heat balance data is information that can be directly inferred from the measured data,
and is as accurate as the measured data that was input to the analysis.
Exhaust Temperature
Compressor Efficiency
Turbine Efficiency
Firing Temperature
Cooling Flows
Heat Rate
Part-Load Temperatures
MapEx calculates the hot gas path temperatures into and out of each nozzle (stator) and bucket (rotor) in the
expander of the gas turbine as measured data changes. The average blade metal temperatures are
determined by the hot gas temperature, the cooling air temperature and the cooling effectiveness.
The chart shows gas turbine firing temperature and exhaust temperature as a function of GT load. Firing
temperature initially decreases as the GT goes to part-load, but then remains essentially constant while the
exhaust temperature increases under guide vane control. When the maximum exhaust temperature is
reached, the exhaust temperature remains constant and the firing temperature decreases with load.