Battery Monitor Installation Guide 20211213

Shenzhen Seplos Technology Co.
, Ltd
User Manual
SEPLOS Smart BMS 8S-16S 50A 100A 150A 200A
1
BatteryMonitor Installation Guide www.seplos.com
Battery Connection - RS485 to USB adapter
1. SEPLOS USB-RS485 adapter, just connect BMS with battery via SEPLOS
USB-RS485 adapter.
2. If the adapter needs wiring, connect the RJ45 cables according to the
following wire diagram.
3. If you buy adapters on the market, make sure the wiring diagram is as
follows, otherwise, the BatteryMonitor software can not be recognized.
2
Software Download and Installation
1. Download the newest version of SEPLOS ‘BatteryMonitor’ software
installation package with the link blow.

https://drive.google.com/drive/folders/10pxgNLHovcDZRVGrCZsSkfecBrRw-AdW?usp=sharing
2. To run the ‘BatteryMonitor’ application, make sure the computer has
installed ‘NET Framework 4.0’ and above. Download the ‘NET
Framework’ installation pack at its official website or at Google Drive site
that shared by SEPLOS.
3
NET Framework official website:
Google Drive site shared by SEPLOS:

Click the link > Click ‘02 Drive’ > Download the ‘BatteryMonitor Software Drive’
3. Double click ‘NET Framework’ to install drive first. And wait for the
progress bar to fill up. Then the BatteryMonitor software drive finished
installation.
4
4. Unzip and extract the compressed file.
Note: Some USB to RJ45 adapters need drive, please make sure you’ve
install the corresponding drive before formally run the BatteryMonitor
application.
Run the software
5. Open ‘BatteryMonitor’ folder. And double click ’BatteryMonitor.exe’
to run the application.
5
6. If a prompt dialogue box pops up, and indicates ’No agreement was
found, please load agreement’ like the following picture showed, please
click ‘OK’.
7. Then choose the ‘16S_V20_ADDR_EN.XML’ agreement (An example
of 48v 100A 16S BMS for LiFePO4 battery.) within the ‘BatteryMonitor’
folder. And click ‘OPEN’ to load the agreement.
6
8. After the prompt dialogue pops up. Click ‘OK’. And the software will
be restarted automatically (Restart time about 10 seconds).

Note: If a incompatible agreement was loaded, please re-choose the
agreement according to your BMS models.
9. The software enters into its home page.
7
10. Before connect with battery system. Make sure the ‘Decimal symbol’,
‘No. of digits after decimal’ and ‘digits grouping symbol’ as follows.
Control panel > Time & Language > Additional data, time & regional settings > Region >
Additional settings
8
11. Choose the port number, which is different for different computer
devices. Check the ports in ‘Device Manager’.
12. Baud rate is 19200. And click ‘Connect’.
Computer Manager > Device Manager > Ports
13. Different adapters may need different drive. (Some computers will
install drive automatically when the adapter is plugged in.) If there isn’t
COM No. Options. Install the drive manually.
Download the drive with the following link:

9
14. When successfully connected with the battery, the battery
information can be read and displayed on the software interface.
15. If BMS fail to connect with battery, a prompt dialogue box will pop
up indicating the connection time out. Please check the port number and
DIP address, then reconnect.
10
16. To manage the parameters, we need to login as administrator.
(Administrator account: admin; Password: admin)
17. After login successfully, choose the menu ‘upload parameter’. Then
double click the parameters that need to modify. And click ‘set all’ to
save the changes. Click ‘save as’ to export the settings for backup.
11
18. The ‘upload menu’ could also manage the ON/OFF of functions.
Double click to choose the switch status. And click ‘set all’ to save the
change.
19. Click ‘communication log’ menu. The communication information of
warning status can be checked.
12
20. Click ‘Real time’, and its background color will turn yellow. BMS will
record the battery information in real-time (Every seconds).
21. And the record data can be read and saved though the ‘Real time
record’ menu. Click ‘Real time’ again, real-time recording will stop
updating.
13
22. Click the ‘History record’. All the historical data can be read and
saved.
23. Current Calibration and Voltage Calibration is for quality control
during manufacturing. (Do not click unless being permitted, or the BMS
will be damaged, and SEPLOS will not responsible for the damage.)
电流校准和电压校准用于出厂质检，只有专业设备才能使用。（未
经允许请勿点击，否则会损坏 BMS，SEPLOS 对因此造车的损坏不承
担任何责任。）
14
24. Click ‘Calibrate’ - ‘Get time’ to get BMS time. If the date and time is
not accurate, click ‘Set time’ to updating. (Make sure the computer date
and time correctly before operating.)
25. When multiple packs in parallel, make sure the DIP address is
correctly set. Check the RS485 DIP ADDRESS SETUP.

15
26. And choose the corresponding packs before clicking ‘connect’. Or
the connection will resulted in time out.
27. Then the ‘BatteryMonitor’ installed successfully. All the cell voltage,
curent, status and historical record can be monitored in real-time.
16

Battery Monitor Installation Guide 20211213

Uploaded by

Copyright:

Available Formats

Battery Monitor Installation Guide 20211213

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Battery Monitor Installation Guide 20211213

Uploaded by

Copyright:

Available Formats

Shenzhen Seplos Technology Co.

Battery Connection - RS485 to USB adapter

following wire diagram.

follows, otherwise, the BatteryMonitor software can not be recognized.

Software Download and Installation

1. Download the newest version of SEPLOS ‘BatteryMonitor’ software

installation package with the link blow.

2. To run the ‘BatteryMonitor’ application, make sure the computer has

installed ‘NET Framework 4.0’ and above. Download the ‘NET

Framework’ installation pack at its official website or at Google Drive site

that shared by SEPLOS.

NET Framework official website:

Google Drive site shared by SEPLOS:

4. Unzip and extract the compressed file.

5. Open ‘BatteryMonitor’ folder. And double click ’BatteryMonitor.exe’

to run the application.

7. Then choose the ‘16S_V20_ADDR_EN.XML’ agreement (An example

folder. And click ‘OPEN’ to load the agreement.

be restarted automatically (Restart time about 10 seconds).

9. The software enters into its home page.

‘No. of digits after decimal’ and ‘digits grouping symbol’ as follows.

devices. Check the ports in ‘Device Manager’.

12. Baud rate is 19200. And click ‘Connect’.

Computer Manager > Device Manager > Ports

COM No. Options. Install the drive manually.

Download the drive with the following link:

14. When successfully connected with the battery, the battery

information can be read and displayed on the software interface.

DIP address, then reconnect.

16. To manage the parameters, we need to login as administrator.

(Administrator account: admin; Password: admin)

19. Click ‘communication log’ menu. The communication information of

warning status can be checked.

record the battery information in real-time (Every seconds).

23. Current Calibration and Voltage Calibration is for quality control

经允许请勿点击，否则会损坏 BMS，SEPLOS 对因此造车的损坏不承

and time correctly before operating.)

correctly set. Check the RS485 DIP ADDRESS SETUP.

26. And choose the corresponding packs before clicking ‘connect’. Or

the connection will resulted in time out.

curent, status and historical record can be monitored in real-time.

You might also like