1564473186374-Question Bank SrDME DSL
1564473186374-Question Bank SrDME DSL
1564473186374-Question Bank SrDME DSL
a) Woodward Governor,
b) MCBG, Answer - a
c) EH Governor,
d) None of the above.
27. HHP Locomotive has a –
a) Two stroke engine,
b) Four stroke engine, Answer - a
c) Multi stroke engine,
d) None of the above.
28. In HHP Locomotive, TSC is fitted in the –
a) Front end of the engine,
b) Rear end of the engine, Answer - b
c) Front or Rear of the engine,
d) None of the above.
29. During EPD testing at idle engine normally shut down in –
a) 120 second, b) 40 second, c) 60 second, d) 35 second. Answer - c
30. EPU Fitted on –
a) Harmonic damper,
b) Starter motor bracket, Answer - b
c) Main alternator,
d) Companion alternator.
31. No. of Radiator fitted in WDP4D Locomotive is –
a) 1, b) 2, c) 4, d) None of the above. Answer - b
32. Radiator fan mounting bolt is torque at –
a) 450 ft-lbs, b) 100 ft-lbs, c) 250 ft-lbs, d) 50 ft-lbs. Answer - b
33. During injector rack setting governor rack should be kept at –
a) 1.00”, b) 1.02”, c) 1.96”, d) 0.62”. Answer - a
34. Power assembly is consisting of –
a) Cylinder liner,
b) Cylinder head, Answer - d
c) Piston, ring, carrier & con rod assembly,
d) All of the above.
35. Liner of HHP Locomotive made of –
a) Cast iron with brazed on outer sleeves,
b) Cast iron alloy with tin plating, Answer - a
c) Stainless steel with chrome plated,
d) Cast iron.
36. Which type of CBC is fitted in WDG4D Locomotive?
a) E-type, b) F-type, c) H-type, d) None of the above. Answer - a
37. At present, which of the following crankcase oils are approved for application in HHP Diesel Engines?
a) Servo RR 520 MG of M/s IOC,
b) MAX RR 517 M of M/s BPC, Answer - d
c) HP RR 817 M of M/s HPC,
d) All of the above.
38. Scavenging pump is a –
a) Reciprocating pump,
b) Centrifugal pump, Answer - c
c) Positive displacement with helical gear type pump,
d) None of the above.
39. No. of starter motor fitted in WDP4D Locomotive is –
a) 1, b) 2, c), 4, d) None of the above. Answer - b
40. Starter Motors of HHP Locomotive is –
a) AC Motor,
QUESTION BANK ON DIESEL LOCOMOTIVES 4
b) DC Series Motor,
c) 3 phase AC Motor, Answer - b
d) None of the above.
41. Starter motors of HHP Locomotive is connected in –
a) Series, b) Parallel, c) Series-parallel, d) None of the above. Answer - b
42. Starter motor used in HHP Locomotive is –
a) 32 volt motors, b) 64 volt motors, Answer - b
c) 72 volts motors, d) None of the above.
43. For starting of HHP Locomotive –
a) Single electric motor is used,
b) Duel electric motor is used, Answer - b
c) Duel air starting motor is used,
d) None of the above.
44. Rating of starting fuse is –
a) 400A, b) 800A, c) 500A, d) None of the above. Answer - b
45. Starting fuse is used –
a) Only during engine starting,
b) Only during engine running, Answer - a
c) Only during engine shutdown,
d) None of the above.
46. How many piston rings are fitted in the HHP Engine Piston?
a) 2, b) 4, c) 5, d) 6. Answer - d
47. In MEDHA Control System if starting fuse is removed during running then -
a) Engine will shut down,
b) Engine will come to idle, Answer - d
c) TE will come to Zero,
d) There will be no effect on engine.
48. Purpose of starting fuse is –
a) To protect the LV (Low voltage) control circuit,
b) To protect the HV (High voltage) control circuit, Answer - c
c) To protect the starter motors from current overload,
d) All of the above.
49. Black light test is related to –
a) Power assembly,
b) Fuel system, Answer - b
c) Turbo supercharger,
d) Lube oil system.
50. No of teeth in starter motor pinion is –
a) 10, b) 15, c) 11, d) None of the above. Answer - c
51. During engine starting, do not hold the fuel prime/engine start switch (FP/ES) to ENGINE START position for more than –
a) 20 seconds, b) 30 seconds,
c) 60 seconds, d) None of the above. Answer - a
52. Backlash to be maintained in between ring gear and starter motor pinion is –
a) 0.008”-0.016”, b) 0.007”-0.025”,
c) 0.015”-0.040”, d) 0.020”-0.030” Answer - c
53. Compressor of HHP Locomotive is –
a) Electrical driven,
b) Mechanical driven, Answer - b
c) Electromagnetic driven,
d) None of the above.
54. What is the meaning of starting abutment?
a) It means starting motor pinion not coming out,
b) It means starting motor pinion not-disengaging with ring gear, Answer - a
QUESTION BANK ON DIESEL LOCOMOTIVES 5
87. In HHP Locomotive, what is the relation between crankshaft & camshaft rpm?
a) Due to two stroke engine, rpm of camshaft = rpm of crankshaft. Answer -a
b) Due to two stroke engine, rpm of camshaft = 1/2 of the rpm of crankshaft.
c) Due to four stroke engine, rpm of camshaft = ½ of the rpm of right crankshaft.
d) None.
88. No. of critical main bearing in HHP Locomotive are –
a) 2, b) 4, c) 5, d) 6. Answer - b
89. Water drain cock is located in –
a) Accessory room,
b) Under truck at loco right side, Answer - a
c) Under truck at loco right side,
d) None.
90. HHP Locomotive is a –
a) Left Hand Driven Locomotive.
b) Right Hand Driven Locomotive. Answer - a
c) Both Hand Driven Locomotive.
d) None of the above.
91. ECC – 4 is found in –
a) WDP4, b) WDG4, c) WDP4B, d) WDG4D. Answer - d
92. Torque valve of Alternator mounting bolt is –
a) 295 ft-lbs, b) 650 ft-lbs, c) 1400 ft-lbs, d) 2400 ft-lbs. Answer - c
93. Which Oil is filled in HHP Loco Fuel Tank?
a) High Speed Diesel Oil,
b) Arctic Diesel Oil, Answer - a
c) Synthetic Diesel Oil,
d) All.
94. What is the height of Rail Guard of HHP Locomotive from Rail Level?
a) 4½”, b) 5½”, c) 6½”, d) None. Answer - a
95. How many Air Inlet Ports are in a power assembly?
QUESTION BANK ON DIESEL LOCOMOTIVES 8
119. In spectrographic analysis of engine lube oil normal range of Sodium (Na) is –
a) 0 – 75 ppm, b) 0 – 50 ppm, c) 0 -30 ppm, d) 0 – 20 ppm. Answer - c
120. In HHP Locomotive which model compressor is used –
a) WLN, b) WLG, c) WBG, d) WBO. Answer - a
121. Which model diesel engine is fitted in HHP Locomotive?
a) 645 G3B, b) 710 G3B, c) 710 G3C, d) None of these. Answer - b
122. “Finger tightness check” is related to –
a) Power assembly,
b) Fuel system, Answer - a
c) Turbo Supercharger,
d) Lube Oil System.
123. In HHP Locomotive, handbrake apply in which wheel?
a) R1 & R2, b) R4 & R5, c) L1 & L2, d) L4 & L5. Answer - b
124. WLN model compressor has –
a) 3 cylinders, b) 4 cylinders, c) 6 cylinders, d) None of these. Answer - a
125. WLN model compressor has –
a)Two low pressure and one high pressure cylinder,
b)Two high pressure and one low pressure cylinder, Answer - a
c)Four low pressure and two high pressure cylinder,
d)Four high pressure and two low pressure cylinder.
126. How many “labyrinth” seals are used in HHP TSC?
a) 1, b) 2, c) 3, d) 4. Answer - c
127. How many spin on filters are fitted in HHP Locomotive?
a) 1, b) 2, c) 3, d) 3 or 4. Answer - d
128. Roller clutch test is done at –
a) 269 rpm, b) 400 rpm, c) 700 rpm, d) 904 rpm. Answer - c
129. TSC of HHP Locomotive is cooled by –
a) Water, b) Lube oil, c) Air, d) Natural Cool. Answer - b
130. How many brake cylinders are fitted in HHP Locomotive?
a) 4, b) 6, c) 8, d) 16. Answer – c
QUESTION BANK ON DIESEL LOCOMOTIVES 10
131. How many 10” expansion joint are fitted in HHP Locomotive?
a) 1, b) 3, c) 4, d) None of these. Answer - a
132. HOD operates when –
a) Cooling water temp rises to 121 - 126 c.
b) Lube Oil temp rises to 121c – 126c. Answer - b
c) Fuel Oil temp rises to 121c - 126c.
d) None of the above.
133. How many dowels are in fork rod and basket assembly?
a) 1, b) 2, c) 3, d) 4. Answer - d
134. Fork rod power assembly is located in which side of engine?
a) Left side, b) Right side, c) Both side, d) None of these. Answer - a
135. Blade rod power assembly is located in which side of engine?
a) Left side, b) Right side, c) Both side, d) None of these. Answer - b
136. What is the pick-up time between one radiator fan to another?
a) 10 seconds, b) 20 seconds, c) 30 seconds, d) None of these. Answer - b
137. Which one is not required for injector rack setting?
a) Concerned power assembly to be kept at TDC.
b) Governor rack to be locked at 1”. Answer - a
c) Rack setting tool to be required.
d) Rotate injector rack adjusting lock nut clockwise direction to lose it.
138. Which type of water pump is fitted in HHP Locomotive?
a) Centrifugal type,
b) Reciprocating type, Answer - a
c) positive displacement type,
d) None of these.
139. Oil separator of HHP Locomotive is cleaned in which schedule?
a) T-30 & above,
b) T-90 & above, Answer - b
c) T-180 & above,
d) T-Yearly & above.
140. How many oil control rings are fitted in the HHP Engine piston?
a) 1, b) 2, c) 3, d) 4. Answer - b
141. What is the discharge capacity of FPM?
a) 5 GPM, b) 7 GPM, c) 10 GPM, d) None of these. Answer - b
142. Maximum permissible height of Diesel Locomotive over Mumbai division is –
a) 4270 mm, b) 4280 mm, c) 4290mm, d) None of these. Answer - a
143. Minimum engine cranking speed needed for starting is –
a) 45 – 50 rpm, b) 60 – 75 rpm, c) 75 – 90 rpm, d) 100 – 120 rpm. Answer -a
144. Maximum speed of WDP4 Locomotive is –
a) 100kmph, b) 105kmph, c) 135kmph, d) 160kmph. Answer - d
145. What is the value of backlash between water pump and governor drive gear?
a) 0.007” – 0.025”,
b) 0.008” – 0.016”, Answer - b
c) 0.010” - 0.025”,
d) 0.006: - 0.018”.
146. What is the minimum engine lube oil viscosity (KV) of HHP Locomotive?
a) 12.8 cst at 100c,
b) 13.0 cst at 100c, Answer - b
c) 18.8 cst at 100c,
d) None of these.
QUESTION BANK ON DIESEL LOCOMOTIVES 11
160. What is the low idle RPM of the WDP4D Locomotive engine?
a) 200, b) 269, c) 350, d) 904 Answer - a
161. What is the height of cattle guard of HHP Locomotive from rail level?
a) 41/2“, b) 51/2”, c) 61/2”, d) None of these. Answer - c
162. How many after cooler are fitted in HHP Locomotive?
a) 1, b) 2, c) 4, d) None of these. Answer - b
163. What is the delivery rate of soak pump in HHP engine?
a) 27 LPM, b) 57 LPM, c) 75 LPM, d) None of these. Answer - b
164. Weight of WDG4D Locomotive is –
a) 126 T, b) 123 T, c) 121.2 T, d) 130.2 T. Answer - d
165. Which oil is fitted in HHP Locomotive compressor?
a) RR 460, b) SP 100, c) RR 606, d) SP 57. Answer - b
166. POP Test is related to –
a) Power assembly,
b) Fuel system, Answer - b
c) Turbo supercharger,
d) Lube oil system.
167. No. of teeth in No. 1 idler Gear is –
a) 58, b) 64, c) 69, d) 79. Answer - b
168. In HHP Locomotive compressor is cooled by –
a) Water, b) Lube oil, c) Air, d) Natural cool. Answer - a
169. Pre-lubrication is related to –
a) Power assembly,
b) Fuel system, Answer - d
c) Turbo supercharger,
d) Lube oil system.
170. Crush height is measured by –
a) Vernier caliper,
b) Outside micrometer, Answer - c
c) Filler gauge,
d) Height gauge.
171. In HHP Locomotive specified limit of exhaust gas temperature is –
a) 315c - 400c, b) 435c - 535c,
c) 490c - 590c, d) None of these. Answer - a
172. Torque value of Exhaust manifold to expansion joint bolts is –
a) 50 ft-lbs, b) 75 ft-lbs, c) 80 ft-lbs, d) 190 ft-lbs. Answer - c
173. In spectrographic analysis of engine lube oil, high range of Copper (Cu) indicates –
a) Internal water leakage,
b) inefficient air filtration, Answer - d
c) cylinder liner wear,
d) bush & bearing wear.
174. Kinematic viscosity is checked at –
a) 40c temp, b) 100c temp, c) 40f temp, d) both a & b. Answer - d
175. Unit of Kinematic viscosity is –
a) CST, b) UST, c) MST, d) PPM. Answer - a
176. In HHP Locomotive compressor lube oil pump is –
a) Belt driven,
b) Gear driven, Answer - b
c) Chain and sprocket driven,
d) All of these.
QUESTION BANK ON DIESEL LOCOMOTIVES 13
177. What is the idle notch RPM of the WDP4D Locomotive engine?
a) 269, b) 904, c) 954, d) 1050. Answer - a
178. How many marks are in HHP Loco Compressor oil dipstick (modified) gauge?
a) 2, b) 3, c) 4, d) None of these. Answer - b
179. Off load condition TSC is driven up to ________ through gear train.
a) 5th Notch, b) 6th Notch, c) 7th Notch, d) 8th Notch. Answer - d
180. Which control system is used in HHP Locomotive?
a) EMD Control System,
b) Medha Control System, Answer - d
c) Siemens Control System,
d) All.
181. Shot peening process is done ins piston ring to improve –
a) Fatigue strength,
b) Tensile strength, Answer - a
c) Compressive strength,
d) None of the above.
182. In MEDHA control system, during pre-lubrication TLPM run for –
a) 120 seconds, b) 900 seconds,
c) 2100 seconds, d) None of these. Answer - b
183. Gear case oil capacity of WDP4D Locomotive is –
a) 7.5 ltrs, b) 8.5 ltrs, c) 9.5 ltrs, d) 9.8 ltrs. Answer - b
184. Gear case oil capacity of WDG4D Loco is –
a) 7.5 ltrs, b) 8.5 ltrs, c) 9.5 ltrs, d) 9.8 ltrs. Answer - a
185. In HHP Locomotive value of cylinder head valve seat angle is –
a) 3000’-3015’,
b) 4500-4515’, Answer - a
c) 6000’-6015’,
d) None of the above.
186. POP Test is conducted to –
a) Check the performance of injector.
b) Check the performance of TSC. Answer - a
c) Check the performance of lash adjuster.
d) Check the performance of air dryer.
187. Water leakage from air box drain pipe indicates –
a) Water inlet tube may be cracked.
b) Cylinder head / liner may be cracked. Answer - d
c) After cooler tube may be punctured.
d) All of the above.
188. VCD Cycle consists of –
a) T0 – Vigilance cycle.
b) T1 & T2 – Warning cycle. Answer - d
c) T3 & T4 – Penalty brake cycle & Penalty brake reset.
d) All of the above.
189. Minimum lube oil level of HHP Loco compressor is –
a) 5 ltrs, b) 6 ltrs, c) 8 ltrs, d) 9.8 ltrs. Answer - b
190. T0 – VCD cycle is called –
a) Vigilance cycle,
b) Warning cycle, Answer - a
c) Penalty brake cycle,
d) All of these.
191. T1 – VCD cycle is called –
a) Vigilance cycle,
QUESTION BANK ON DIESEL LOCOMOTIVES 14
b) Warning cycle,
c) Penalty brake cycle, Answer - b
d) All of these.
192. T2 – VCD cycle is called –
a) Vigilance cycle,
b) Warning cycle, Answer - b
c) Penalty brake cycle,
d) All of these.
193. T3 – VCD cycle is called –
a) Vigilance cycle,
b) Warning cycle, Answer - c
c) Penalty brake cycle,
d) All of these.
194. T4 – VCD cycle is called –
a) Vigilance cycle,
b) Warning cycle, Answer - c
c) Penalty brake reset cycle,
d) All of these.
195. Duration of T0 Cycle is –
a) 60 second, b) 8 ± 2 second,
c) 34 ± 2 second, d) None of these. Answer - a
196. Duration of T1 Cycle is –
a) 60 second, b) 8 ± 2 second,
c) 34 ± 2 second, d) None of these. Answer - b
197. Duration of T3 Cycle is –
a) 60 second, b) 8 ± 2 second,
c) 34 ± 2 second, d) None of these. Answer - b
198. At present, which of the following crankcase oils are approved for application in HHP Diesel engines?
a) Servo RR 520 MG & RR 606 MG Plus II of M/s IOC,
b) MAX RR 517 M of M/s BPC, Answer - d
c) HP RR 817 M of M/s HPC,
d) All of these.
199. In HHP Locomotive duration of suction period is –
a) 87, b) 113, c) 16.6, d) 138. Answer - a
200. FPM of HHP Locomotive is a –
a) AC Motor,
b) DC Series Motor, Answer - c
c) 3 phase AC Motor,
d) None of these.
201. Air dryer is fitted -
a) Before MR1 Reservoir,
b) Between MR1 & MR2 Reservoir, Answer - b
c) Between MR2 & CCB System,
d) After MR2 Reservoir.
202. Shot peening is related to –
a) Lube oil cooler,
b) Piston ring, Answer - b
c) Turbo supercharger,
d) Clutch gear assembly.
203. Final torque value of crab nut is -
a) 250 ft-lbs, b) 400 ft-lbs, c) 450 ft-lbs, d) 2400 ft-lbs. Answer - d
204. Crush height is related to –
a) Power assembly,
QUESTION BANK ON DIESEL LOCOMOTIVES 15
b) Fuel system,
c) Turbo supercharger, Answer - a
d) Lube oil system.
205. In spectrographic analysis of engine lube oil normal range of copper (Cu) is –
a) 0 – 75 ppm, b) 0 – 50 ppm, c) 0 – 20 ppm, d) 0 – 15 ppm. Answer - a
206. Compressor lube oil dipstick is located on the –
a) Left side of the Locomotive.
b) Right side of the Locomotive. Answer - a
c) Both side of the Locomotive.
d) None of these.
207. Length of WDP4D Locomotive is –
a) 22.98 meters, b) 21.24 meters,
c) 21.7 meters, d) None of these. Answer - a
208. In HHP Locomotive compressor air intake filter is changed during –
a) T-30 & above schedule.
b) T-60 & above schedule. Answer - d
c) T-90 & above schedule.
d) T-180 & above schedule.
209. Free air delivery of GD compressor is –
a) 4000 LPM, b) 5000 LPM, c) 6000 LPM, d) 9000 LPM. Answer - c
210. OSTA of HHP (4500 HP) locomotive is set at –
a) 1035-1050 rpm,
b) 1035-1075 rpm, Answer - c
c) 1085-1100 rpm,
d) 1185-1220 rpm.
211. OSTA of HHP (4000 HP) locomotive is set at –
a) 1035-1050 rpm, b) 1035-1075 rpm,
c) 1085-1100 rpm, d) 1185-1220 rpm. Answer - a
212. HHP Locomotive brake block is made of –
a) Cast Iron, b) Fiber, c) Composite material, d) None of these. Answer - c
213. In HHP Locomotive pilot stud of liner is located at –
a) 05 o’clock, b) 06 o’clock, c) 12 o’clock, d) 13 o’clock. Answer - a
214. Maximum speed of WDG4D Locomotive is –
a) 100 kmph, b) 105 kmph, c) 135 kmph, d) 160 kmph. Answer - b
215. In HHP Locomotive, when OSTA is set, reset handle rest at –
a) 11’ O clock position,
b) 13’ O clock position, Answer - a
c) 12’ O clock position,
d) None of these.
216. In HHP Locomotive Lube Oil Strainer is fitted on –
a) Right side, Front end of the Engine,
b) Right side, Rear end of the Engine. Answer - a
c) Left side, Front end of the Engine.
d) Left side, Rear end of the Engine.
217. In HHP Locomotive, bearing to crankpin maximum clearance is –
a) 0.010”, b) 0.015”, c) 0.020”, d) 0.0205”. Answer - b
218. In HHP Locomotive Brake Cylinder pressure is adjusted at –
a) 1.8kg/cm2, b) 3.5kg/cm2, c) 5.2kg/cm2, d) None of these. Answer - c
219. In HHP Locomotive compression stroke end at –
a) BDC, b) 43.5 after BDC, c) TDC, d) 67 after TDC. Answer - c
220. Torque the rocker arm adjusting screw lock nut approximately –
QUESTION BANK ON DIESEL LOCOMOTIVES 16
a) 70 – 75 ft-lbs, b) 75 – 80 ft-lbs,
c) 80 – 85 ft-lbs, d) 85 – 90 ft-lbs. Answer - c
221. POH of HHP Locomotive done after –
a) 8 years, b) 12 years, c) 15 years, d) 18 years. Answer - d
222. Cylinder head seat ring minimum permissible thickness is –
a) 4.67mm, b) 4.44 mm, c) 1.73mm, d) None of these. Answer - a
223. From initial to final torque value, crab nut rotates approximately –
a) 120 ± 35, b) 200 ± 35, c) 250 ± 35, d) 360 ± 35. Answer - b
224. Fuel tank capacity of WDP4D Locomotive is –
a) 5000 ltrs, b) 6000 ltrs, c) 6500 ltrs, d) None of these. Answer - a
225. What is the function of the compression ring? Answer - b
a) Pull the piston down when cylinder is not firing.
b) Prevent the compressed air and gases enter into the crankcase.
c) Prevent the lube oil entering into the air box and combustion chamber.
d) All of the above.
226. Maximum permissible limit of fuel dilution in HHP Lube Oil is –
a) 2 per cent, b) 3 per cent, c) 5 per cent, d) 10 per cent. Answer - c
227. Maximum permissible limit of water contamination in HHP Lube Oil is –
a) 2 per cent, b) 3 per cent, c) 5 per cent, d) 0 per cent. Answer - d
228. In HHP Locomotive, the following model Woodward Governor is fitted –
a) PGR, b) PGEV, c) PGR & PGEV, d) None of these. Answer - b
229. Which of the following valve is not fitted in HHP Locomotive compressed air system?
a) Duplex check valve, b) FT1 Feed Valve,
c) NRV, d) None of these. Answer - a
230. In HHP Locomotive A9 handle is called –
a) Auto brake handle,
b) Direct brake handle, Answer - a
c) Bail of ring,
d) None of these.
231. Fuel oil primary filter conditioning gauge needle in green zone indicates fuel oil –
a) Differential pressure is 20 ± 2 psi.
b) Differential pressure is 25 ± 2 psi. Answer - a
c) Differential pressure is 30 ± 2 psi.
d) None of the above.
232. Thrust washer is made of –
a) Cast iron with brazed on outer sleeves.
b) Cast iron alloy with tin plating. Answer - d
c) Stainless steel with chrome plated.
d) Copper.
233. In HHP Locomotive which type torsional damper is fitted – Answer - b
a) Spring pack type, b) Gear type, c) Viscous type, d) Pendulum type.
234. In HHP Locomotive Inlet port open at –
a) 43.5 before BDC,
b) 107.5 after TDC, Answer - a
c) 180 after TDC,
d) 67 after BDC.
266. Before re-cranking engine, wait for minimum _________ minutes to cool starter motor –
a) 1, b) 2, c) 3, d) 4. Answer -c
267. How many sand boxes are fitted in HHP Locomotive?
a) 4, b) 8, c) 12, d) 16. Answer - b
268. Minimum Flash Point of RR – 520 is –
a) 35c, b) 194c, c) 240c, d) None of these. Answer - b
269. To increase OSTA Tripping rpm –
a) OSTA adjusting spring tension to be increased.
QUESTION BANK ON DIESEL LOCOMOTIVES 19
276. In Siemens, Control System during dynamic braking, engine raise to – Answer - b
a) 2nd Notch rpm, b) 4th Notch rpm, c) 6th Notch rpm, d) None of these.
277. How many planet gears are fitted in HHP TSC?
a) 1, b) 2, c) 3, d) 4. Answer - c
278. Which of the following operation is performed during “Crush Height Check”?
a) Do finger tightness check and tight upper basket bolt to 35 ft-lbs.
b) Tight lower basket bolt to 10 ft-lbs. Answer - d
c) Measure basket flange joint gap with filler gauge. Flange joint gap should be in between 0.008” to 0.017”.
d) All of the above.
279. During torqueing of crab nut –
a) Torque outboard nuts first then the inboard nut.
b) Torque inboard nuts first then the outboard nut. Answer - a
c) Torque the four crab nuts of power assembly crosswise only.
d) All of the above.
280. “Crush Height Check” is done to avoid the failure of –
a) Con-rod bearing seizure,
b) Main bearing seizure, Answer - a
c) Thrust collar seizure,
d) All.
281. In HHP Locomotive engine cylinders are cooled by –
a) Water, b) Air, c) Supercharged air and water, d) Lube oil. Answer - c
282. Maximum tractive effort of WDG4 Locomotive is –
a) 42 tones, b) 23 tones, c) 53 tones, d) 39 tones. Answer - c
283. Cam of HHP Locomotive is checked in which schedule?
a) T-30 & above schedule,
QUESTION BANK ON DIESEL LOCOMOTIVES 20
296. Don’t off ___________ circuit breaker immediate after engine shut down –
a) Computer and TLPM, b) Battery knife switch.
c) Local control, d) GBPM. Answer - a
297. Don’t crank the engine without external pre-lubrication if engine has not been cranked for more than –
a) 24 hours, b) 36 hours, c) 48 hours, d) 72 hours. Answer - c
298. Don’t try to raise the engine before engine coolant temperature has been raised –
a) 42, b) 52, c) 62, d) 72. Answer - b
299. Purging cycle of air dryer is – Answer - c
QUESTION BANK ON DIESEL LOCOMOTIVES 21
458. Bubbles in the fuel return sight glass during priming indicates –
a) Air draw in suction side of the fuel booster pump,
b) The leaky fuel injector, Answer - a
c) Insufficient fuel supply,
d) None of these.
459. Bubbles in the fuel return sight glass after cranking the engine indicates –
a) Air draw in suction side of the fuel booster pump,
b) The leaky fuel injector, Answer - b
c) Insufficient fuel supply,
d) None of these.
460. Bubbles in the fuel return sight glass in higher notch with full load indicates -
a) Air draw in suction side of the fuel booster pump,
b) The leaky fuel injector, Answer - c
c) Insufficient fuel supply,
d) None of these.
461. To charge feed pipe at 6kg/cm2 air pressure which valve is fitted –
a) F2 Feed Valve, b) FT1 Feed Valve,
c) C2N Feed Valve, d) Any one of these. Answer - d
462. Auto brake valve handle has –
a) 2 positions, b) 3 positions, c) 5 positions, d) None of these. Answer - c
463. In HHP Locomotive wheel to brake block clearance is –
a) 10 mm, b) Depend upon the location of the wheel,
c) Independent on the location of the wheel, d) None of these. Answer - b
464. In HHP Locomotive, FP Pressure is set at –
a) 6.0 ± 0.1kg/cm2, b) 6.1 ± 0.1kg/cm2, Answer - a
c) 6.2 ± 0.1kg/cm2, d) None of these.
465. In HHP Locomotive fuel oil spin on filter is fitted on –
a) Right side, Front end of the Engine,
b) Right side, Rear end of the Engine, Answer - a
c) Left side, Front end of the Engine,
d) None of these.
466. During DBI Testing of MR Tank of HHP Locomotive, hydraulic testing is done at –
a) 1 time working pressure,
b) 1.5 times working pressure, Answer - b
c) 2 times working pressure,
d) None of these.
467. In HHP Locomotive, exhaust valve close at –
a) 43.5º before BDC,
b) 43.5º after BDC, Answer - d
c) 107.5º after TDC,
d) 67º after BDC.
468. To operate ABD, air supply is received from –
a) MR-1, b) MR-2, c) MR-4, d) None of these. Answer - a
469. TM Blower air duct (bellow) is changed at –
a) T – 360 schedule, b) T – 720 schedule,
c) 3 yearly schedules, d) 6 yearly schedules. Answer - d
470. VCD alarm sound during –
a) T0 Cycle, b) T1 Cycle, c) T2 cycle, d) T4 cycle. Answer - c
471. In which VCD Cycle, yellow flashing light is glow –
a) T1 Cycle, c) T2 cycle, d) T3 cycle, d) All of these. Answer - d
472. Engine Lube Oil sample analysis is done in –
a) T – 30 & above schedule,
QUESTION BANK ON DIESEL LOCOMOTIVES 31
535. At the time of Dynamic braking the Grid resistance takes from –
a) Generator/Alternator, b) Traction Motor, Answer -
c) Both Generator and Alternator, d) None of these.
536. At the time of Dynamic braking the Main Generator gives supply to –
a) Traction Motor Field, b) TM Armature,
c) Both Traction Motor and Field, d) None of the above. Answer -
537. At the time of Dynamic braking the Traction Motor –
a) Not working, b) Working as Motor, Answer -
c) Working as Generator, d) None of these.
538. Which of the following normally Minimum and Maximum voltage?
a) 1.8/28V, b) 08/28V, c) 53//40V, d) 4/35V. Answer -
539. At the time of Dynamic braking all TM field connected as in –
a) Series connection, b) Parallel Connection,
c) Series – Parallel Connection, d) None of these. Answer -
540. What is the condemning size of BKBL Carbon brush –
a) ½ inch, b) 1inch, c)11/2 inch, d) None Answer -
541. BKBL Motor is a –
a) DC Series Motor, b) DC Shunt Motor,
c) AC Series Motor, d) None of these. Answer -
542. What happened if BKBL opened at the time of Dynamic braking –
a) Low Grid current, b) Max. Grid current,
c) No braking effort, d) None of these. Answer -
543. No. of carbon brush in BKBL Motor –
a) 6 nos., b) 8 nos., c) 2 nos. d) None of the above. Answer -
544. How many holders in Traction Generator (BHEL)? – a) 12, b) 10, c) 9. Answer -
QUESTION BANK ON DIESEL LOCOMOTIVES 35
567. Diameter of the Governor lube oil pressure sensing pipe line is -
QUESTION BANK ON DIESEL LOCOMOTIVES 36
571. Which of the following position are in Driver’s backup brake valve – Answer - d
a) V – Emergency Position, b) III – Lap Position, c) II – Running Position, d) All of these.
583. No. of teeth in Governor Drive Gear is – a) 37, b) 131, c) 80, d) 113. Answer - d
586. No. of teeth in Camshaft Drive Gear is – a) 26, b) 37, c) 79, d) 113. Answer - c
602. Lube oil consumption of HHP Loco compressor should not be more than –
a) 1.5 ltrs/month, b) 2 ltrs/month, c) 3 ltrs/month, ) 3.5 ltrs/month. Answer - a
603. In HHP Loco compressor discharge air temp. at HP outlet may allowed upto –
a) 100ºc, B) 150ºc, C) 200ºc, D) 250ºc. Answer - c
604. In HHP MU, loading and unloading of compressor of both loco is synchronized by –
a) MVCC of leading loco, b) MVCC of trailing loco,
c) CMPSYN relay, d) None of these. Answer - c
605. In HHP Locomotive, LP and HP cylinders of compressor are arranging with an angle of –
a) 30º between them, b) 45º between them,
c) 60º between them, d) 90º between them. Answer - c
606. Rising copper levels in lubrication oil is a concern of high -
a) Thrust washer wear, b) Piston wear,
c) Liner wear, d) None of the above. Answer - a
607. Maximum allowable wear limit of thrust washer is -
a) 0.070” – Based on change in lead wear reading, Answer - c
b) 0.080” – Based on absolute snap ring clearance reading,
c) Both a & b,
d) None of these.
608. Thrust washer wear in a power pack can be determined by –
a) Change in lead wear reading, b) Absolute snap ring clearance,
c) both a & b, d) None. Answer - c
609. To check Thrust washer wear by “absolute snap ring clearance” method concerned piston to be kept in –
a) TDC, b) BDC, c) 45º after TDC, d) 221/2º after TDC. Answer - b
610. Which pressure is adjusted by limiting valve
a) F-1 pressure b) BP pressure,
c) FP pressure, d) Synchronization pressure Answer - d
611. When emergency brake application is done through A-9 in flasher light modified loco the condition of loco will be-
a) Loco comes to idle and nothing else happens,
b) Loco comes to idle, flasher light is on,
c) Loco comes to idle, flasher light is on & buzzer blows, Answer - a
d) Loco does not come to idle, flasher light is on & buzzer blows.